Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input layer updates from Dmitry Torokhov:
 - a bunch of new drivers (DA9052/53 touchscreenn controller, Synaptics
   Navpoint, LM8333 keypads, Wacom I2C touhscreen);
 - updates to existing touchpad drivers (ALPS, Sntelic);
 - Wacom driver now supports Intuos5;
 - device-tree bindings in numerous drivers;
 - other cleanups and fixes.

Fix annoying conflict in drivers/input/tablet/wacom_wac.c that I think
implies that the input layer device naming is broken, but let's see.  I
brough it up with Dmitry.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
  Input: matrix-keymap - fix building keymaps
  Input: spear-keyboard - document DT bindings
  Input: spear-keyboard - add device tree bindings
  Input: matrix-keymap - wire up device tree support
  Input: matrix-keymap - uninline and prepare for device tree support
  Input: adp5588 - add support for gpio names
  Input: omap-keypad - dynamically handle register offsets
  Input: synaptics - fix compile warning
  MAINTAINERS: adjust input-related patterns
  Input: ALPS - switch to using input_mt_report_finger_count
  Input: ALPS - add semi-MT support for v4 protocol
  Input: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
  Input: atmel_mxt_ts - dump each message on just 1 line
  Input: atmel_mxt_ts - do not read extra (checksum) byte
  Input: atmel_mxt_ts - verify object size in mxt_write_object
  Input: atmel_mxt_ts - only allow root to update firmware
  Input: atmel_mxt_ts - use CONFIG_PM_SLEEP
  Input: sentelic - report device's production serial number
  Input: tl6040-vibra - Device Tree support
  Input: evdev - properly handle read/write with count 0
  ...

Documentation/devicetree/bindings/input/spear-keyboard.txt

@@ -0,0 +1,20 @@
+* SPEAr keyboard controller
+
+Required properties:
+- compatible: "st,spear300-kbd"
+
+Optional properties, in addition to those specified by the shared
+matrix-keyboard bindings:
+- autorepeat: bool: enables key autorepeat
+- st,mode: keyboard mode: 0 - 9x9, 1 - 6x6, 2 - 2x2
+
+Example:
+
+kbd@fc400000 {
+	compatible = "st,spear300-kbd";
+	reg = <0xfc400000 0x100>;
+	linux,keymap = < 0x00030012
+			 0x0102003a >;
+	autorepeat;
+	st,mode = <0>;
+};

Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt

@@ -0,0 +1,16 @@
+* NXP LPC32xx SoC Touchscreen Controller (TSC)
+
+Required properties:
+- compatible: must be "nxp,lpc3220-tsc"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: The TSC/ADC interrupt
+
+Example:
+
+	tsc@40048000 {
+		compatible = "nxp,lpc3220-tsc";
+		reg = <0x40048000 0x1000>;
+		interrupt-parent = <&mic>;
+		interrupts = <39 0>;
+	};

Documentation/devicetree/bindings/input/twl6040-vibra.txt

@@ -0,0 +1,37 @@
+Vibra driver for the twl6040 family
+
+The vibra driver is a child of the twl6040 MFD dirver.
+Documentation/devicetree/bindings/mfd/twl6040.txt
+
+Required properties:
+- compatible : Must be "ti,twl6040-vibra";
+- interrupts: 4, Vibra overcurrent interrupt
+- vddvibl-supply: Regulator supplying the left vibra motor
+- vddvibr-supply: Regulator supplying the right vibra motor
+- vibldrv_res: Board specific left driver resistance
+- vibrdrv_res: Board specific right driver resistance
+- viblmotor_res: Board specific left motor resistance
+- vibrmotor_res: Board specific right motor resistance
+
+Optional properties:
+- vddvibl_uV: If the vddvibl default voltage need to be changed
+- vddvibr_uV: If the vddvibr default voltage need to be changed
+
+Example:
+/*
+ * 8-channel high quality low-power audio codec
+ * http://www.ti.com/lit/ds/symlink/twl6040.pdf
+ */
+twl6040: twl6040@4b {
+	...
+	twl6040_vibra: twl6040@1 {
+		compatible = "ti,twl6040-vibra";
+		interrupts = <4>;
+		vddvibl-supply = <&vbat>;
+		vddvibr-supply = <&vbat>;
+		vibldrv_res = <8>;
+		vibrdrv_res = <3>;
+		viblmotor_res = <10>;
+		vibrmotor_res = <10>;
+	};
+};