Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits)
  regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
  regulator: max8925: fix enabled/disabled judgement mistake
  regulator: add regulator_bulk_force_disable function
  regulator: pass regulator_register of_node in fixed voltage driver
  regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR
  regulator: Enable supply regulator if child rail is enabled.
  regulator: mc13892: Convert to devm_kzalloc()
  regulator: mc13783: Convert to devm_kzalloc()
  regulator: Fix checking return value of create_regulator
  regulator: Fix the error handling if create_regulator fails
  regulator: Export regulator_is_supported_voltage()
  regulator: mc13892: add device tree probe support
  regulator: mc13892: remove the unnecessary prefix from regulator name
  regulator: Convert wm831x regulator drivers to devm_kzalloc()
  regulator: da9052: Staticize non-exported symbols
  regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
  regulator: Update da9052-regulator for DT changes
  regulator: DA9052/53 Regulator support
  regulator: pass device_node to of_get_regulator_init_data()
  regulator: If a single voltage is set with device tree then set apply_uV
  ...

Documentation/devicetree/bindings/regulator/fixed-regulator.txt

@@ -0,0 +1,29 @@
+Fixed Voltage regulators
+
+Required properties:
+- compatible: Must be "regulator-fixed";
+
+Optional properties:
+- gpio: gpio to use for enable control
+- startup-delay-us: startup time in microseconds
+- enable-active-high: Polarity of GPIO is Active high
+If this property is missing, the default assumed is Active low.
+
+Any property defined as part of the core regulator
+binding, defined in regulator.txt, can also be used.
+However a fixed voltage regulator is expected to have the
+regulator-min-microvolt and regulator-max-microvolt
+to be the same.
+
+Example:
+
+	abc: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 16 0>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+		regulator-boot-on
+	};

Documentation/devicetree/bindings/regulator/regulator.txt

@@ -0,0 +1,54 @@
+Voltage/Current Regulators
+
+Optional properties:
+- regulator-name: A string used as a descriptive name for regulator outputs
+- regulator-min-microvolt: smallest voltage consumers may set
+- regulator-max-microvolt: largest voltage consumers may set
+- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops
+- regulator-min-microamp: smallest current consumers may set
+- regulator-max-microamp: largest current consumers may set
+- regulator-always-on: boolean, regulator should never be disabled
+- regulator-boot-on: bootloader/firmware enabled regulator
+- <name>-supply: phandle to the parent supply/regulator node
+
+Example:
+
+	xyzreg: regulator@0 {
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+		vin-supply = <&vin>;
+	};
+
+Regulator Consumers:
+Consumer nodes can reference one or more of its supplies/
+regulators using the below bindings.
+
+- <name>-supply: phandle to the regulator node
+
+These are the same bindings that a regulator in the above
+example used to reference its own supply, in which case
+its just seen as a special case of a regulator being a
+consumer itself.
+
+Example of a consumer device node (mmc) referencing two
+regulators (twl_reg1 and twl_reg2),
+
+	twl_reg1: regulator@0 {
+		...
+		...
+		...
+	};
+
+	twl_reg2: regulator@1 {
+		...
+		...
+		...
+	};
+
+	mmc: mmc@0x0 {
+		...
+		...
+		vmmc-supply = <&twl_reg1>;
+		vmmcaux-supply = <&twl_reg2>;
+	};