Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC platform updates from Olof Johansson:
 "SoC updates, mostly refactorings and cleanups of old legacy platforms.

  Major themes this release:

   - Conversion of ixp4xx to a modern platform (drivers, DT, bindings)

   - Moving some of the ep93xx headers around to get it closer to
     multiplatform enabled.

   - Cleanups of Davinci

  This also contains a few patches that were queued up as fixes before
  5.1 but I didn't get sent in before release"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
  ARM: debug-ll: add default address for digicolor
  ARM: u300: regulator: add MODULE_LICENSE()
  ARM: ep93xx: move private headers out of mach/*
  ARM: ep93xx: move pinctrl interfaces into include/linux/soc
  ARM: ep93xx: keypad: stop using mach/platform.h
  ARM: ep93xx: move network platform data to separate header
  ARM: stm32: add AMBA support for stm32 family
  MAINTAINERS: update arch/arm/mach-davinci
  ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
  ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
  soc: ixp4xx: qmgr: Add DT probe code
  soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
  soc: ixp4xx: npe: Add DT probe code
  soc: ixp4xx: Add DT bindings for IXP4xx NPE
  soc: ixp4xx: qmgr: Pass resources
  soc: ixp4xx: Remove unused functions
  soc: ixp4xx: Uninline several functions
  soc: ixp4xx: npe: Pass addresses as resources
  ARM: ixp4xx: Turn the QMGR into a platform device
  ARM: ixp4xx: Turn the NPE into a platform device
  ...

arch/arm/boot/dts/Makefile

@@ -229,6 +229,9 @@ dtb-$(CONFIG_ARCH_HIX5HD2) += \
 dtb-$(CONFIG_ARCH_INTEGRATOR) += \
 	integratorap.dtb \
 	integratorcp.dtb
+dtb-$(CONFIG_ARCH_IXP4XX) += \
+	intel-ixp42x-linksys-nslu2.dtb \
+	intel-ixp43x-gateworks-gw2358.dtb
 dtb-$(CONFIG_ARCH_KEYSTONE) += \
 	keystone-k2hk-evm.dtb \
 	keystone-k2l-evm.dtb \

arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi

@@ -88,6 +88,7 @@
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
 		enable-active-high;
 	};
 
@@ -99,6 +100,7 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
 		enable-active-high;
 		regulator-always-on;
 	};
@@ -216,7 +218,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-duration = <10>;
 	phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	phy-supply = <&reg_enet>;

arch/arm/boot/dts/imx6dl-riotboard.dts

@@ -92,7 +92,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/boot/dts/imx6q-ba16.dtsi

@@ -171,7 +171,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 

arch/arm/boot/dts/imx6q-marsboard.dts

@@ -110,7 +110,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6q-tbs2910.dts

@@ -98,7 +98,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-apf6.dtsi

@@ -51,7 +51,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-duration = <10>;
 	phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	status = "okay";

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -292,7 +292,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;

arch/arm/boot/dts/imx6qdl-sabresd.dtsi

@@ -202,7 +202,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-sr-som.dtsi

@@ -53,7 +53,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-duration = <2>;
 	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
 	status = "okay";

arch/arm/boot/dts/imx6qdl-wandboard.dtsi

@@ -224,7 +224,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/boot/dts/imx6sx-sabreauto.dts

@@ -75,7 +75,7 @@
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	fsl,magic-packet;
 	status = "okay";

arch/arm/boot/dts/imx6sx-sdb.dtsi

@@ -191,7 +191,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
 	phy-supply = <&reg_enet_3v3>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
 	status = "okay";

arch/arm/boot/dts/imx7d-pico.dtsi

@@ -92,7 +92,7 @@
 			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
 	fsl,magic-packet;
 	phy-reset-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;

arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts

@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Linksys NSLU2
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)";
+	compatible = "linksys,nslu2", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-status {
+			label = "nslu2:red:status";
+			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+		led-ready {
+			label = "nslu2:green:ready";
+			gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+		led-disk-1 {
+			label = "nslu2:green:disk-1";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led-disk-2 {
+			label = "nslu2:green:disk-2";
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-power {
+			wakeup-source;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		};
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_ESC>;
+			label = "reset";
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@6f {
+			compatible = "xicor,x1205";
+			reg = <0x6f>;
+		};
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+		timeout-ms = <5000>;
+	};
+
+	/* The first 16MB region on the expansion bus */
+	flash@50000000 {
+		compatible = "intel,ixp4xx-flash", "cfi-flash";
+		bank-width = <2>;
+		/*
+		 * 8 MB of Flash in 0x20000 byte blocks
+		 * mapped in at 0x50000000
+		 */
+		reg = <0x50000000 0x800000>;
+
+		partitions {
+			compatible = "redboot-fis";
+			/* Eraseblock at 0x7e0000 */
+			fis-index-block = <0x3f>;
+		};
+	};
+};

arch/arm/boot/dts/intel-ixp42x.dtsi

@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP 42x series. This series has 32 interrupts.
+ */
+#include "intel-ixp4xx.dtsi"
+
+/ {
+	soc {
+		interrupt-controller@c8003000 {
+			compatible = "intel,ixp42x-interrupt";
+		};
+
+		/*
+		 * This is the USB Device Mode (UDC) controller, which is used
+		 * to present the IXP4xx as a device on a USB bus.
+		 */
+		usb@c800b000 {
+			compatible = "intel,ixp4xx-udc";
+			reg = <0xc800b000 0x1000>;
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+	};
+};

arch/arm/boot/dts/intel-ixp43x-gateworks-gw2358.dts

@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Gateworks IXP43x-based Cambria GW2358
+ */
+
+/dts-v1/;
+
+#include "intel-ixp43x.dtsi"
+
+/ {
+	model = "Gateworks Cambria GW2358";
+	compatible = "gateworks,gw2358", "intel,ixp43x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 128 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-user {
+			label = "gw2358:green:LED";
+			gpios = <&pld1 0 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hwmon@28 {
+			compatible = "adi,ad7418";
+			reg = <0x28>;
+		};
+		rtc: ds1672@68 {
+			compatible = "dallas,ds1672";
+			reg = <0x68>;
+		};
+		eeprom@51 {
+			compatible = "atmel,24c08";
+			reg = <0x51>;
+			pagesize = <16>;
+			size = <1024>;
+			read-only;
+		};
+		pld0: pld@56 {
+			compatible = "gateworks,pld-gpio";
+			reg = <0x56>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+		/* This PLD just handles the LED and user button */
+		pld1: pld@57 {
+			compatible = "gateworks,pld-gpio";
+			reg = <0x57>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+
+	flash@50000000 {
+		compatible = "intel,ixp4xx-flash", "cfi-flash";
+		bank-width = <2>;
+		/*
+		 * 32 MB of Flash in 0x20000 byte blocks
+		 * mapped in at 0x50000000
+		 */
+		reg = <0x50000000 0x2000000>;
+
+		partitions {
+			compatible = "redboot-fis";
+			/* Eraseblock at 0x1fe0000 */
+			fis-index-block = <0xff>;
+		};
+	};
+};

arch/arm/boot/dts/intel-ixp43x.dtsi

@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP 43x series. This series has 64 interrupts and adds a few more
+ * peripherals over the 42x series.
+ */
+#include "intel-ixp4xx.dtsi"
+
+/ {
+	soc {
+		interrupt-controller@c8003000 {
+			compatible = "intel,ixp43x-interrupt";
+		};
+	};
+};

arch/arm/boot/dts/intel-ixp45x-ixp46x.dtsi

@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP45x and IXP46x series. This series has 64 interrupts and adds a
+ * few more peripherals over the 42x and 43x series so this extends the
+ * basic IXP4xx DTSI.
+ */
+#include "intel-ixp4xx.dtsi"
+
+/ {
+	soc {
+		interrupt-controller@c8003000 {
+			compatible = "intel,ixp43x-interrupt";
+		};
+
+		/*
+		 * This is the USB Device Mode (UDC) controller, which is used
+		 * to present the IXP4xx as a device on a USB bus.
+		 */
+		usb@c800b000 {
+			compatible = "intel,ixp4xx-udc";
+			reg = <0xc800b000 0x1000>;
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		i2c@c8011000 {
+			compatible = "intel,ixp4xx-i2c";
+			reg = <0xc8011000 0x18>;
+			interrupts = <33 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+	};
+};

arch/arm/boot/dts/intel-ixp4xx.dtsi

@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Intel XScale Network Processors
+ * in the IXP 4xx series.
+ */
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+		interrupt-parent = <&intcon>;
+
+		qmgr: queue-manager@60000000 {
+			compatible = "intel,ixp4xx-ahb-queue-manager";
+			reg = <0x60000000 0x4000>;
+			interrupts = <3 IRQ_TYPE_LEVEL_HIGH>, <4 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		uart0: serial@c8000000 {
+			compatible = "intel,xscale-uart";
+			reg = <0xc8000000 0x1000>;
+			/*
+			 * The reg-offset and reg-shift is a side effect
+			 * of running the platform in big endian mode.
+			 */
+			reg-offset = <3>;
+			reg-shift = <2>;
+			interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <14745600>;
+			no-loopback-test;
+		};
+
+		gpio0: gpio@c8004000 {
+			compatible = "intel,ixp4xx-gpio";
+			reg = <0xc8004000 0x1000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		intcon: interrupt-controller@c8003000 {
+			/*
+			 * Note: no compatible string. The subvariant of the
+			 * chip needs to define what version it is. The
+			 * location of the interrupt controller is fixed in
+			 * memory across all variants.
+			 */
+			reg = <0xc8003000 0x100>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		timer@c8005000 {
+			compatible = "intel,ixp4xx-timer";
+			reg = <0xc8005000 0x100>;
+			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		npe@c8006000 {
+			compatible = "intel,ixp4xx-network-processing-engine";
+			reg = <0xc8006000 0x1000>, <0xc8007000 0x1000>, <0xc8008000 0x1000>;
+		};
+	};
+};

arch/arm/boot/dts/ls1021a-twr.dts

@@ -145,7 +145,7 @@
 };
 
 &enet0 {
-	tbi-handle = <&tbi1>;
+	tbi-handle = <&tbi0>;
 	phy-handle = <&sgmii_phy2>;
 	phy-connection-type = "sgmii";
 	status = "okay";
@@ -225,6 +225,13 @@
 	sgmii_phy2: ethernet-phy@2 {
 		reg = <0x2>;
 	};
+	tbi0: tbi-phy@1f {
+		reg = <0x1f>;
+		device_type = "tbi-phy";
+	};
+};
+
+&mdio1 {
 	tbi1: tbi-phy@1f {
 		reg = <0x1f>;
 		device_type = "tbi-phy";

arch/arm/boot/dts/ls1021a.dtsi

@@ -729,7 +729,7 @@
 		};
 
 		mdio0: mdio@2d24000 {
-			compatible = "gianfar";
+			compatible = "fsl,etsec2-mdio";
 			device_type = "mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -737,6 +737,15 @@
 			      <0x0 0x2d10030 0x0 0x4>;
 		};
 
+		mdio1: mdio@2d64000 {
+			compatible = "fsl,etsec2-mdio";
+			device_type = "mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2d64000 0x0 0x4000>,
+			      <0x0 0x2d50030 0x0 0x4>;
+		};
+
 		ptp_clock@2d10e00 {
 			compatible = "fsl,etsec-ptp";
 			reg = <0x0 0x2d10e00 0x0 0xb0>;

arch/arm/boot/dts/sun8i-a23-a33.dtsi

@@ -169,6 +169,8 @@
 			clock-names = "ahb", "mod";
 			resets = <&ccu RST_BUS_NAND>;
 			reset-names = "ahb";
+			pinctrl-names = "default";
+			pinctrl-0 = <&nand_pins &nand_pins_cs0 &nand_pins_rb0>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;