Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

arch/arm/mach-pxa/sleep.S

@@ -0,0 +1,194 @@
+/*
+ * Low-level PXA250/210 sleep/wakeUp support
+ *
+ * Initial SA1110 code:
+ * Copyright (c) 2001 Cliff Brake <cbrake@accelent.com>
+ *
+ * Adapted for PXA by Nicolas Pitre:
+ * Copyright (c) 2002 Monta Vista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License.
+ */
+
+#include <linux/config.h>
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/hardware.h>
+
+#include <asm/arch/pxa-regs.h>
+
+		.text
+
+/*
+ * pxa_cpu_suspend()
+ *
+ * Forces CPU into sleep state
+ */
+
+ENTRY(pxa_cpu_suspend)
+
+	mra	r2, r3, acc0
+	stmfd	sp!, {r2 - r12, lr}		@ save registers on stack
+
+	@ get coprocessor registers
+	mrc	p14, 0, r3, c6, c0, 0		@ clock configuration, for turbo mode
+	mrc	p15, 0, r4, c15, c1, 0		@ CP access reg
+	mrc	p15, 0, r5, c13, c0, 0		@ PID
+	mrc 	p15, 0, r6, c3, c0, 0		@ domain ID
+	mrc 	p15, 0, r7, c2, c0, 0		@ translation table base addr
+	mrc	p15, 0, r8, c1, c1, 0           @ auxiliary control reg
+	mrc 	p15, 0, r9, c1, c0, 0		@ control reg
+
+	bic	r3, r3, #2			@ clear frequency change bit
+
+	@ store them plus current virtual stack ptr on stack
+	mov	r10, sp
+	stmfd	sp!, {r3 - r10}
+
+	@ preserve phys address of stack
+	mov	r0, sp
+	bl	sleep_phys_sp
+	ldr	r1, =sleep_save_sp
+	str	r0, [r1]
+
+	@ clean data cache
+	bl	xscale_flush_kern_cache_all
+
+	@ Put the processor to sleep
+	@ (also workaround for sighting 28071)
+
+	@ prepare value for sleep mode
+	mov	r1, #3				@ sleep mode
+
+	@ prepare to put SDRAM into self-refresh manually
+	ldr	r4, =MDREFR
+	ldr	r5, [r4]
+	orr	r5, r5, #MDREFR_SLFRSH
+
+	@ prepare pointer to physical address 0 (virtual mapping in generic.c)
+	mov	r2, #UNCACHED_PHYS_0
+
+	@ Intel PXA255 Specification Update notes problems
+	@ about suspending with PXBus operating above 133MHz
+	@ (see Errata 31, GPIO output signals, ... unpredictable in sleep
+	@
+	@ We keep the change-down close to the actual suspend on SDRAM
+	@ as possible to eliminate messing about with the refresh clock
+	@ as the system will restore with the original speed settings
+	@
+	@ Ben Dooks, 13-Sep-2004
+
+	ldr	r6, =CCCR
+	ldr	r8, [r6]		@ keep original value for resume
+
+	@ ensure x1 for run and turbo mode with memory clock
+	bic	r7, r8, #CCCR_M_MASK | CCCR_N_MASK
+	orr	r7, r7, #(1<<5) | (2<<7)
+
+	@ check that the memory frequency is within limits
+	and	r14, r7, #CCCR_L_MASK
+	teq	r14, #1
+	bicne	r7, r7, #CCCR_L_MASK
+	orrne	r7, r7, #1			@@ 99.53MHz
+
+	@ get ready for the change
+
+	@ note, turbo is not preserved over sleep so there is no
+	@ point in preserving it here. we save it on the stack with the
+	@ other CP registers instead.
+	mov	r0, #0
+	mcr	p14, 0, r0, c6, c0, 0
+	orr	r0, r0, #2			@ initiate change bit
+
+	@ align execution to a cache line
+	b	1f
+
+	.ltorg
+	.align	5
+1:
+
+	@ All needed values are now in registers.
+	@ These last instructions should be in cache
+
+	@ initiate the frequency change...
+	str	r7, [r6]
+	mcr	p14, 0, r0, c6, c0, 0
+
+	@ restore the original cpu speed value for resume
+	str	r8, [r6]
+
+	@ put SDRAM into self-refresh
+	str	r5, [r4]
+
+	@ force address lines low by reading at physical address 0
+	ldr	r3, [r2]
+
+	@ enter sleep mode
+	mcr	p14, 0, r1, c7, c0, 0
+
+20:	b	20b				@ loop waiting for sleep
+
+/*
+ * cpu_pxa_resume()
+ *
+ * entry point from bootloader into kernel during resume
+ *
+ * Note: Yes, part of the following code is located into the .data section.
+ *       This is to allow sleep_save_sp to be accessed with a relative load
+ *       while we can't rely on any MMU translation.  We could have put
+ *       sleep_save_sp in the .text section as well, but some setups might
+ *       insist on it to be truly read-only.
+ */
+
+	.data
+	.align 5
+ENTRY(pxa_cpu_resume)
+	mov	r0, #PSR_I_BIT | PSR_F_BIT | MODE_SVC	@ set SVC, irqs off
+	msr	cpsr_c, r0
+
+	ldr	r0, sleep_save_sp		@ stack phys addr
+	ldr	r2, =resume_after_mmu		@ its absolute virtual address
+	ldmfd	r0, {r3 - r9, sp}		@ CP regs + virt stack ptr
+
+	mov	r1, #0
+	mcr	p15, 0, r1, c8, c7, 0   	@ invalidate I & D TLBs
+	mcr	p15, 0, r1, c7, c7, 0		@ invalidate I & D caches, BTB
+
+#ifdef CONFIG_XSCALE_CACHE_ERRATA
+	bic     r9, r9, #0x0004			@ see cpu_xscale_proc_init
+#endif
+
+	mcr	p14, 0, r3, c6, c0, 0		@ clock configuration, turbo mode.
+	mcr	p15, 0, r4, c15, c1, 0		@ CP access reg
+	mcr	p15, 0, r5, c13, c0, 0		@ PID
+	mcr 	p15, 0, r6, c3, c0, 0		@ domain ID
+	mcr 	p15, 0, r7, c2, c0, 0		@ translation table base addr
+	mcr	p15, 0, r8, c1, c1, 0           @ auxiliary control reg
+	b	resume_turn_on_mmu		@ cache align execution
+
+	.align 5
+resume_turn_on_mmu:
+	mcr 	p15, 0, r9, c1, c0, 0		@ turn on MMU, caches, etc.
+
+	@ Let us ensure we jump to resume_after_mmu only when the mcr above
+	@ actually took effect.  They call it the "cpwait" operation.
+	mrc	p15, 0, r1, c2, c0, 0		@ queue a dependency on CP15
+	sub	pc, r2, r1, lsr #32		@ jump to virtual addr
+	nop
+	nop
+	nop
+
+sleep_save_sp:
+	.word	0				@ preserve stack phys ptr here
+
+	.text
+resume_after_mmu:
+#ifdef CONFIG_XSCALE_CACHE_ERRATA
+	bl	cpu_xscale_proc_init
+#endif
+	ldmfd	sp!, {r2, r3}
+	mar	acc0, r2, r3
+	ldmfd	sp!, {r4 - r12, pc}		@ return to caller
+
+