Merge tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Fix a few memoryleaks
   - Minor improvements to the card initialization sequence
   - Partially support sleepy GPIO controllers for pwrseq eMMC

  MMC host:
   - alcor: Work with multiple-entry sglists
   - alcor: Enable DMA for writes
   - meson-gx: Improve tuning support
   - meson-gx: Avoid clock glitch when switching to DDR modes
   - meson-gx: Disable unreliable HS400 mode
   - mmci: Minor updates for support of HW busy detection
   - mmci: Support data transfers for the stm32_sdmmc variant
   - mmci: Restructure code to better support different variants
   - mtk-sd: Add support for version found on MT7620 family SOCs
   - mtk-sd: Add support for the MT8516 version
   - mtk-sd: Add Chaotian Jing as the maintainer
   - sdhci: Reorganize request-code to convert from tasklet to workqueue
   - sdhci_am654: Stabilize support for lower speed modes
   - sdhci-esdhc-imx: Add HS400 support for iMX7ULP
   - sdhci-esdhc-imx: Add support for iMX7ULP version
   - sdhci-of-arasan: Allow to disable DCMDs via DT for CQE
   - sdhci-of-esdhc: Add support for the ls1028a version
   - sdhci-of-esdhc: Several fixups for errata
   - sdhci-pci: Fix BYT OCP setting
   - sdhci-pci: Add support for Intel CML
   - sdhci-tegra: Add support for system suspend/resume
   - sdhci-tegra: Add CQE support for Tegra186 WAR
   - sdhci-tegra: Add support for Tegra194
   - sdhci-tegra: Update HW tuning process

  MEMSTICK:
   - I volunteered to help as a maintainer for the memstick subsystem,
     which is reflected by an update to the MAINTAINERS file. Changes
     are funneled through my MMC git and we will use the linux-mmc
     mailing list.

  MEMSTICK host:
   - A few minor cleanups"

* tag 'mmc-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (87 commits)
  mmc: sdhci-pci: Fix BYT OCP setting
  dt-bindings: mmc: add DT bindings for ls1028a eSDHC host controller
  mmc: alcor: Drop pointer to mmc_host from alcor_sdmmc_host
  mmc: mtk-sd: select REGULATOR
  mmc: mtk-sd: enable internal card-detect logic.
  mmc: mtk-sd: add support for config found in mt7620 family SOCs.
  mmc: mtk-sd: don't hard-code interrupt trigger type
  mmc: core: Fix tag set memory leak
  dt-bindings: mmc: Add support for MT8516 to mtk-sd
  mmc: mmci: Prevent polling for busy detection in IRQ context
  mmc: mmci: Cleanup mmci_cmd_irq() for busy detect
  mmc: usdhi6rol0: mark expected switch fall-throughs
  mmc: core: Verify SD bus width
  mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP
  mmc: sdhci-esdhc-imx: add pm_qos to interact with cpuidle
  dt-bindings: mmc: fsl-imx-esdhc: add imx7ulp compatible string
  mmc: meson-gx: add signal resampling tuning
  mmc: meson-gx: remove Rx phase tuning
  mmc: meson-gx: avoid clock glitch when switching to DDR modes
  mmc: meson-gx: disable HS400
  ...

drivers/mmc/core/host.c

@@ -363,11 +363,11 @@ int mmc_of_parse_voltage(struct device_node *np, u32 *mask)
 	int num_ranges, i;
 
 	voltage_ranges = of_get_property(np, "voltage-ranges", &num_ranges);
-	num_ranges = num_ranges / sizeof(*voltage_ranges) / 2;
 	if (!voltage_ranges) {
 		pr_debug("%pOF: voltage-ranges unspecified\n", np);
 		return 0;
 	}
+	num_ranges = num_ranges / sizeof(*voltage_ranges) / 2;
 	if (!num_ranges) {
 		pr_err("%pOF: voltage-ranges empty\n", np);
 		return -EINVAL;
@@ -429,8 +429,6 @@ struct mmc_host *mmc_alloc_host(int extra, struct device *dev)
 
 	if (mmc_gpio_alloc(host)) {
 		put_device(&host->class_dev);
-		ida_simple_remove(&mmc_host_ida, host->index);
-		kfree(host);
 		return NULL;
 	}
 

drivers/mmc/core/mmc_ops.c

@@ -184,11 +184,7 @@ int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
 		if (err)
 			break;
 
-		/* if we're just probing, do a single pass */
-		if (ocr == 0)
-			break;
-
-		/* otherwise wait until reset completes */
+		/* wait until reset completes */
 		if (mmc_host_is_spi(host)) {
 			if (!(cmd.resp[0] & R1_SPI_IDLE))
 				break;
@@ -200,6 +196,16 @@ int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
 		err = -ETIMEDOUT;
 
 		mmc_delay(10);
+
+		/*
+		 * According to eMMC specification v5.1 section 6.4.3, we
+		 * should issue CMD1 repeatedly in the idle state until
+		 * the eMMC is ready. Otherwise some eMMC devices seem to enter
+		 * the inactive mode after mmc_init_card() issued CMD0 when
+		 * the eMMC device is busy.
+		 */
+		if (!ocr && !mmc_host_is_spi(host))
+			cmd.arg = cmd.resp[0] | BIT(30);
 	}
 
 	if (rocr && !mmc_host_is_spi(host))

drivers/mmc/core/pwrseq_emmc.c

@@ -30,19 +30,14 @@ struct mmc_pwrseq_emmc {
 
 #define to_pwrseq_emmc(p) container_of(p, struct mmc_pwrseq_emmc, pwrseq)
 
-static void __mmc_pwrseq_emmc_reset(struct mmc_pwrseq_emmc *pwrseq)
-{
-	gpiod_set_value(pwrseq->reset_gpio, 1);
-	udelay(1);
-	gpiod_set_value(pwrseq->reset_gpio, 0);
-	udelay(200);
-}
-
 static void mmc_pwrseq_emmc_reset(struct mmc_host *host)
 {
 	struct mmc_pwrseq_emmc *pwrseq =  to_pwrseq_emmc(host->pwrseq);
 
-	__mmc_pwrseq_emmc_reset(pwrseq);
+	gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
+	udelay(1);
+	gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
+	udelay(200);
 }
 
 static int mmc_pwrseq_emmc_reset_nb(struct notifier_block *this,
@@ -50,8 +45,11 @@ static int mmc_pwrseq_emmc_reset_nb(struct notifier_block *this,
 {
 	struct mmc_pwrseq_emmc *pwrseq = container_of(this,
 					struct mmc_pwrseq_emmc, reset_nb);
+	gpiod_set_value(pwrseq->reset_gpio, 1);
+	udelay(1);
+	gpiod_set_value(pwrseq->reset_gpio, 0);
+	udelay(200);
 
-	__mmc_pwrseq_emmc_reset(pwrseq);
 	return NOTIFY_DONE;
 }
 
@@ -72,14 +70,18 @@ static int mmc_pwrseq_emmc_probe(struct platform_device *pdev)
 	if (IS_ERR(pwrseq->reset_gpio))
 		return PTR_ERR(pwrseq->reset_gpio);
 
-	/*
-	 * register reset handler to ensure emmc reset also from
-	 * emergency_reboot(), priority 255 is the highest priority
-	 * so it will be executed before any system reboot handler.
-	 */
-	pwrseq->reset_nb.notifier_call = mmc_pwrseq_emmc_reset_nb;
-	pwrseq->reset_nb.priority = 255;
-	register_restart_handler(&pwrseq->reset_nb);
+	if (!gpiod_cansleep(pwrseq->reset_gpio)) {
+		/*
+		 * register reset handler to ensure emmc reset also from
+		 * emergency_reboot(), priority 255 is the highest priority
+		 * so it will be executed before any system reboot handler.
+		 */
+		pwrseq->reset_nb.notifier_call = mmc_pwrseq_emmc_reset_nb;
+		pwrseq->reset_nb.priority = 255;
+		register_restart_handler(&pwrseq->reset_nb);
+	} else {
+		dev_notice(dev, "EMMC reset pin tied to a sleepy GPIO driver; reset on emergency-reboot disabled\n");
+	}
 
 	pwrseq->pwrseq.ops = &mmc_pwrseq_emmc_ops;
 	pwrseq->pwrseq.dev = dev;

drivers/mmc/core/queue.c

@@ -472,6 +472,7 @@ void mmc_cleanup_queue(struct mmc_queue *mq)
 		blk_mq_unquiesce_queue(q);
 
 	blk_cleanup_queue(q);
+	blk_mq_free_tag_set(&mq->tag_set);
 
 	/*
 	 * A request can be completed before the next request, potentially

drivers/mmc/core/sd.c

@@ -221,6 +221,14 @@ static int mmc_decode_scr(struct mmc_card *card)
 
 	if (scr->sda_spec3)
 		scr->cmds = UNSTUFF_BITS(resp, 32, 2);
+
+	/* SD Spec says: any SD Card shall set at least bits 0 and 2 */
+	if (!(scr->bus_widths & SD_SCR_BUS_WIDTH_1) ||
+	    !(scr->bus_widths & SD_SCR_BUS_WIDTH_4)) {
+		pr_err("%s: invalid bus width\n", mmc_hostname(card->host));
+		return -EINVAL;
+	}
+
 	return 0;
 }