proprietary_vendor_samsung_e1q/proprietary/vendor/etc/libese-nxp.conf

##This file needs to be pushed into /vendor/etc/libese-nxp.conf

###############################################################################
# Application options
SE_DEBUG_ENABLED=1


#Timeout in secs
NXP_SWP_RD_TAG_OP_TIMEOUT=0xFF

#WTX Count in secs
NXP_WTX_COUNT_VALUE=180

#Max WTX Count in OSU mode in secs
NXP_OSU_MAX_WTX_COUNT=60

#Delay(us) to recover if invalid data received
RNACK_RETRY_DELAY=7000

# PN67T_PWR_SCHEME          0x01
# PN80T_LEGACY_PWR_SCHEME   0x02
# PN80T_EXT_PMU_SCHEME      0x03
NXP_POWER_SCHEME=0x02

# For SOF = 0x5A            0x01
# For SOF = 0x00            0x02
NXP_SOF_WRITE=0x01

#SPI Thorughput measurement log enabled(1)/disabled(0) in kernel
NXP_TP_MEASUREMENT=0x00

#Enable/Disable interface reset as part of SPI open
NXP_SPI_INTF_RST_ENABLE=0x01

###############################################################################
# SPI WRITE TIMEOUT for RF event synchronization
NXP_SPI_WRITE_TIMEOUT=0x14

###############################################################################
# SPI Device Node name
NXP_ESE_DEV_NODE="/dev/p61"

#MAX NO OF R_NACK RETRY ALLOWED IN CASE OF CRC FAILURE
NXP_MAX_RNACK_RETRY=0x03
NXP_VISO_DPD_ENABLED=0x01
#NXP_NAD_POLL_RETRY_TIME is in 100's of us
# e.g. 0x05 --> 500 us dealy
NXP_NAD_POLL_RETRY_TIME=0x05
###############################################################################
# P61 interface options for JCOP Download
# NFC 0x01
# SPI 0x02
NXP_P61_JCOP_DEFAULT_INTERFACE=0x01

###############################################################################
# IFS adjustment configuration value of IFSD for eSE
# Any value set which is greater than IFSC value will be R-NACKed from JCOP
# Default IFSC: 0x00FE = (0x0102 - 0x4(header))(As agreed with JCOP)
#
NXP_ESE_IFSD_VALUE=0x0200

###############################################################################
# IFS adjustment configuration value of IFSD for eUICC
# Any value set which is greater than IFSC value will be R-NACKed from JCOP
# Default IFSC: 0x00FE = (0x0102 - 0x4(header))(As agreed with JCOP)
#
NXP_EUICC_IFSD_VALUE=0x0200

###############################################################################
# Interface to perform the eSE cold reset
# Possible value can be 0x00 or 0x01
# 0x00 = ESE_HAL
# 0x01 = NFC_HAL
NXP_P61_COLD_RESET_INTERFACE=0x00

###############################################################################
# Assign terminal number to each interface based on system config
NXP_SPI_SE_TERMINAL_NUM="eSE1"

###############################################################################
# Identify the CHIP/OS version for which this config file is targeted
# Possible value can be as below
# 0x01 = JCOP_4_0
# 0x02 = JCOP_5_1
# 0x03 = JCOP_5_2
NXP_OS_VERSION=0x03

###############################################################################