| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113 |
- # SPDX-License-Identifier: GPL-2.0-only
- #
- # Phy drivers for TI platforms
- #
- config PHY_DA8XX_USB
- tristate "TI DA8xx USB PHY Driver"
- depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
- select GENERIC_PHY
- select MFD_SYSCON
- help
- Enable this to support the USB PHY on DA8xx SoCs.
- This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
- config PHY_DM816X_USB
- tristate "TI dm816x USB PHY driver"
- depends on ARCH_OMAP2PLUS || COMPILE_TEST
- depends on USB_SUPPORT
- select GENERIC_PHY
- select USB_PHY
- help
- Enable this for dm816x USB to work.
- config PHY_AM654_SERDES
- tristate "TI AM654 SERDES support"
- depends on OF && (ARCH_K3 || COMPILE_TEST)
- depends on COMMON_CLK
- select GENERIC_PHY
- select MULTIPLEXER
- select REGMAP_MMIO
- select MUX_MMIO
- help
- This option enables support for TI AM654 SerDes PHY used for
- PCIe.
- config PHY_J721E_WIZ
- tristate "TI J721E WIZ (SERDES Wrapper) support"
- depends on OF && (ARCH_K3 || COMPILE_TEST)
- depends on HAS_IOMEM && OF_ADDRESS
- depends on COMMON_CLK
- select GENERIC_PHY
- select MULTIPLEXER
- select REGMAP_MMIO
- select MUX_MMIO
- help
- This option enables support for WIZ module present in TI's J721E
- SoC. WIZ is a serdes wrapper used to configure some of the input
- signals to the SERDES (Sierra/Torrent). This driver configures
- three clock selects (pll0, pll1, dig) and resets for each of the
- lanes.
- config OMAP_CONTROL_PHY
- tristate "OMAP CONTROL PHY Driver"
- depends on ARCH_OMAP2PLUS || COMPILE_TEST
- help
- Enable this to add support for the PHY part present in the control
- module. This driver has API to power on the USB2 PHY and to write to
- the mailbox. The mailbox is present only in omap4 and the register to
- power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
- additional register to power on USB3 PHY/SATA PHY/PCIE PHY
- (PIPE3 PHY).
- config OMAP_USB2
- tristate "OMAP USB2 PHY Driver"
- depends on ARCH_OMAP2PLUS || ARCH_K3
- depends on USB_SUPPORT
- select GENERIC_PHY
- select USB_PHY
- select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST
- help
- Enable this to support the transceiver that is part of SOC. This
- driver takes care of all the PHY functionality apart from comparator.
- The USB OTG controller communicates with the comparator using this
- driver.
- config TI_PIPE3
- tristate "TI PIPE3 PHY Driver"
- depends on ARCH_OMAP2PLUS || COMPILE_TEST
- select GENERIC_PHY
- select OMAP_CONTROL_PHY
- help
- Enable this to support the PIPE3 PHY that is part of TI SOCs. This
- driver takes care of all the PHY functionality apart from comparator.
- This driver interacts with the "OMAP Control PHY Driver" to power
- on/off the PHY.
- config PHY_TUSB1210
- tristate "TI TUSB1210 ULPI PHY module"
- depends on USB_ULPI_BUS
- select GENERIC_PHY
- help
- Support for TI TUSB1210 USB ULPI PHY.
- config TWL4030_USB
- tristate "TWL4030 USB Transceiver Driver"
- depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
- depends on USB_SUPPORT
- depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y'
- select GENERIC_PHY
- select USB_PHY
- help
- Enable this to support the USB OTG transceiver on TWL4030
- family chips (including the TWL5030 and TPS659x0 devices).
- This transceiver supports high and full speed devices plus,
- in host mode, low speed.
- config PHY_TI_GMII_SEL
- tristate
- select GENERIC_PHY
- select REGMAP
- help
- This driver supports configuring of the TI CPSW Port mode depending on
- the Ethernet PHY connected to the CPSW Port.
|
