8a01b9d7ec
Add ini support to configure traffic shaping for COEX i.e. coex_tput_shaping_enable.Host sends this INI to Firmware via WMI_COEX_CONFIG_ENABLE_TPUT_SHAPING. Based on this enabled value, FW will do power save with AP when BT page scan is enabled. The default behaviour is to do a free run without notifying a power save to the AP during the BT Page scan. Change-Id: I4934c98911b66c7c834899ad7cdc72063e9c5153 CRs-Fixed: 3066980
423 Zeilen
8.9 KiB
C
423 Zeilen
8.9 KiB
C
/*
|
||
* Copyright (c) 2012 - 2021 The Linux Foundation. All rights reserved.
|
||
* Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
|
||
*
|
||
* Permission to use, copy, modify, and/or distribute this software for
|
||
* any purpose with or without fee is hereby granted, provided that the
|
||
* above copyright notice and this permission notice appear in all
|
||
* copies.
|
||
*
|
||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
|
||
* WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
|
||
* WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE
|
||
* AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL
|
||
* DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
|
||
* PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
|
||
* TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
|
||
* PERFORMANCE OF THIS SOFTWARE.
|
||
*/
|
||
|
||
/**
|
||
* DOC: This file contains centralized definitions of converged configuration.
|
||
*/
|
||
|
||
#ifndef __CFG_COEX_H
|
||
#define __CFG_COEX_H
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetBTCMode - Config BTC mode
|
||
* @Min: 0
|
||
* @Max: 2
|
||
* @Default: 0
|
||
*
|
||
* 0 - TDD
|
||
* 1 - FDD
|
||
* 2 - Hybrid
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BTC_MODE CFG_INI_UINT( \
|
||
"gSetBTCMode", \
|
||
0, \
|
||
2, \
|
||
0, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"BTC mode")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetAntennaIsolation - Set Antenna Isolation
|
||
* @Min: 0
|
||
* @Max: 255
|
||
* @Default: 25
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_ANTENNA_ISOLATION CFG_INI_UINT( \
|
||
"gSetAntennaIsolation", \
|
||
0, \
|
||
255, \
|
||
25, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"Antenna Isolation")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetMaxTxPowerForBTC - Set Max WLAN Tx power in COEX scenario
|
||
* @Min: 0
|
||
* @Max: 100
|
||
* @Default: 100
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_MAX_TX_POWER_FOR_BTC CFG_INI_UINT( \
|
||
"gSetMaxTxPowerForBTC", \
|
||
0, \
|
||
100, \
|
||
100, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"Max Tx Power for BTC")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetWlanLowRssiThreshold - Set WLAN low RSSI threshold for BTC mode switching
|
||
* @Min: -100
|
||
* @Max: 0
|
||
* @Default: -80
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_WLAN_LOW_RSSI_THRESHOLD CFG_INI_INT( \
|
||
"gSetWlanLowRssiThreshold", \
|
||
-100, \
|
||
0, \
|
||
-80, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"WLAN Low RSSI Threshold")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetBtLowRssiThreshold - Set BT low RSSI threshold for BTC mode switching
|
||
* @Min: -100
|
||
* @Max: 0
|
||
* @Default: -80
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BT_LOW_RSSI_THRESHOLD CFG_INI_INT( \
|
||
"gSetBtLowRssiThreshold", \
|
||
-100, \
|
||
0, \
|
||
-80, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"BT Low RSSI Threshold")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetBtInterferenceLowLL - Set lower limit of low level BT interference
|
||
* @Min: -100
|
||
* @Max: 100
|
||
* @Default: -25
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BT_INTERFERENCE_LOW_LL CFG_INI_INT( \
|
||
"gSetBtInterferenceLowLL", \
|
||
-100, \
|
||
100, \
|
||
-25, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"BT Interference Low LL")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetBtInterferenceLowUL - Set upper limit of low level BT interference
|
||
* @Min: -100
|
||
* @Max: 100
|
||
* @Default: -21
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BT_INTERFERENCE_LOW_UL CFG_INI_INT( \
|
||
"gSetBtInterferenceLowUL", \
|
||
-100, \
|
||
100, \
|
||
-21, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"BT Interference Low UL")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetBtInterferenceMediumLL - Set lower limit of medium level BT interference
|
||
* @Min: -100
|
||
* @Max: 100
|
||
* @Default: -20
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BT_INTERFERENCE_MEDIUM_LL CFG_INI_INT( \
|
||
"gSetBtInterferenceMediumLL", \
|
||
-100, \
|
||
100, \
|
||
-20, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"BT Interference Medium LL")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetBtInterferenceMediumUL - Set upper limit of medium level BT interference
|
||
* @Min: -100
|
||
* @Max: 100
|
||
* @Default: -16
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BT_INTERFERENCE_MEDIUM_UL CFG_INI_INT( \
|
||
"gSetBtInterferenceMediumUL", \
|
||
-100, \
|
||
100, \
|
||
-16, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"BT Interference Medium UL")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetBtInterferenceHighLL - Set lower limit of high level BT interference
|
||
* @Min: -100
|
||
* @Max: 100
|
||
* @Default: -15
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BT_INTERFERENCE_HIGH_LL CFG_INI_INT( \
|
||
"gSetBtInterferenceHighLL", \
|
||
-100, \
|
||
100, \
|
||
-15, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"BT Interference High LL")
|
||
|
||
/*
|
||
* <ini>
|
||
* gSetBtInterferenceHighUL - Set upper limit of high level BT interference
|
||
* @Min: -100
|
||
* @Max: 100
|
||
* @Default: -11
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BT_INTERFERENCE_HIGH_UL CFG_INI_INT( \
|
||
"gSetBtInterferenceHighUL", \
|
||
-100, \
|
||
100, \
|
||
-11, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"BT Interference High UL")
|
||
|
||
#ifdef FEATURE_MPTA_HELPER
|
||
/*
|
||
* <ini>
|
||
* gMPTAHelperEnable - Enable MPTA Helper
|
||
* @Min: 0
|
||
* @Max: 1
|
||
* @Default: 0
|
||
*
|
||
* This ini is used to enable or disable coex MPTA Helper.
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_COEX_MPTA_HELPER CFG_INI_BOOL( \
|
||
"gMPTAHelperEnable", \
|
||
0, \
|
||
"Enable/Disable MPTA Helper")
|
||
|
||
#define COEX_MPTA_HELPER_CFG CFG(CFG_COEX_MPTA_HELPER)
|
||
#else
|
||
#define COEX_MPTA_HELPER_CFG
|
||
#endif
|
||
|
||
/*
|
||
* <ini>
|
||
* gBtScoAllowWlan2GScan - Allow wlan 2g scan when BT SCO connection is on
|
||
* @Min: 0
|
||
* @Max: 1
|
||
* @Default: 1
|
||
*
|
||
* 0 - Disable
|
||
* 1 - Enable
|
||
*
|
||
* This ini is used to enable or disable wlan 2g scan
|
||
* when BT SCO connection is on.
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BT_SCO_ALLOW_WLAN_2G_SCAN CFG_INI_BOOL( \
|
||
"gBtScoAllowWlan2GScan", \
|
||
1, \
|
||
"Bt Sco Allow Wlan 2G Scan")
|
||
|
||
/*
|
||
* <ini>
|
||
* ble_scan_coex_policy - Ini to configure coex policy
|
||
* @Min: 0
|
||
* @Max: 1
|
||
* @Default: 0
|
||
*
|
||
* 0 - Better BLE Advertiser reception performance
|
||
* 1 - Better WLAN performance
|
||
*
|
||
* This ini is used to control the performance of ble scan case,’0’ to place
|
||
* more emphasis on BLE Scan results , ‘1’ to place more emphasis on WLAN
|
||
* performance
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_BLE_SCAN_COEX_POLICY CFG_INI_BOOL( \
|
||
"ble_scan_coex_policy", \
|
||
0, \
|
||
"BLE scan Coex policy")
|
||
|
||
#ifdef FEATURE_COEX_CONFIG
|
||
/*
|
||
* <ini>
|
||
* gThreeWayCoexConfigLegacyEnable - Enable coex config legacy feature
|
||
* @Min: 0
|
||
* @Max: 1
|
||
* @Default: 0
|
||
*
|
||
* This ini is used to enable or disable three way coex config legacy feature.
|
||
* This feature is designed only for non-mobile solution.
|
||
* When the feature is disabled, Firmware use the default configuration to
|
||
* set the coex priority of three antenna(WLAN, BT, ZIGBEE).
|
||
* when enable this feature, customer can use the vendor command to set antenna
|
||
* coex priority dynamically.
|
||
*
|
||
* Supported Feature: three way coex config
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_THREE_WAY_COEX_CONFIG_LEGACY CFG_INI_BOOL( \
|
||
"gThreeWayCoexConfigLegacyEnable", \
|
||
0, \
|
||
"Enable/Disable COEX Config Legacy")
|
||
|
||
#define THREE_WAY_COEX_CONFIG_LEGACY_CFG CFG(CFG_THREE_WAY_COEX_CONFIG_LEGACY)
|
||
#else
|
||
#define THREE_WAY_COEX_CONFIG_LEGACY_CFG
|
||
#endif
|
||
|
||
#ifdef FEATURE_BTC_CHAIN_MODE
|
||
/*
|
||
* <ini>
|
||
* gSetInitChainModeForBTC - Used to set init chain mode for BTC
|
||
* @Min: 0
|
||
* @Max: 0xFF
|
||
* @Default: 0xFF
|
||
*
|
||
* This ini is used to set init chain mode for BTC, default value
|
||
* should be set to the same as macro WLAN_COEX_BTC_CHAIN_MODE_UNSETTLED(0xFF),
|
||
* only below values can be set:
|
||
* 0 - init WLAN 2.4G to support 2x2.
|
||
* It means chains of BT and WLAN 2.4G are shared, or BT is OFF.
|
||
* 1 - init WLAN 2.4G as 1x1, chains of BT and WLAN 2.4G are separated,
|
||
* fixed FDD.
|
||
* 2 - init WLAN 2.4G as 1x1, chains of BT and WLAN 2.4G are separated,
|
||
* hybrid mode
|
||
* 0xFF - no need to send init chain mode for BTC to firmware.
|
||
*
|
||
* Supported Feature: init chain mode for BTC
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_SET_INIT_CHAIN_MODE_FOR_BTC CFG_INI_UINT( \
|
||
"gSetInitChainModeForBTC", \
|
||
0, \
|
||
0xFF, \
|
||
0xFF, \
|
||
CFG_VALUE_OR_DEFAULT, \
|
||
"Init Chain Mode For BTC")
|
||
|
||
#define SET_INIT_CHAIN_MODE_FOR_BTC_CFG CFG(CFG_SET_INIT_CHAIN_MODE_FOR_BTC)
|
||
#else
|
||
#define SET_INIT_CHAIN_MODE_FOR_BTC_CFG
|
||
#endif
|
||
|
||
#ifdef FEATURE_COEX_TPUT_SHAPING_CONFIG
|
||
/*
|
||
* <ini>
|
||
* coex_tput_shaping_enable - Ini to enable wifi configure traffic shaping
|
||
* @Min: 0
|
||
* @Max: 1
|
||
* @Default: 0
|
||
*
|
||
* 0 - traffic shaping is disable
|
||
* 1 - traffic shaping is enable
|
||
*
|
||
* This ini is used to enable and disable wifi traffic shaping
|
||
*
|
||
* Usage: External
|
||
*
|
||
* </ini>
|
||
*/
|
||
#define CFG_TPUT_SHAPING_ENABLE CFG_INI_BOOL( \
|
||
"coex_tput_shaping_enable", \
|
||
0, \
|
||
"coex_tput_shaping_enable")
|
||
#define TPUT_SHAPING_ENABLE_CFG CFG(CFG_TPUT_SHAPING_ENABLE)
|
||
#else
|
||
#define TPUT_SHAPING_ENABLE_CFG
|
||
#endif
|
||
|
||
#define CFG_COEX_ALL \
|
||
CFG(CFG_BTC_MODE) \
|
||
CFG(CFG_ANTENNA_ISOLATION) \
|
||
CFG(CFG_MAX_TX_POWER_FOR_BTC) \
|
||
CFG(CFG_WLAN_LOW_RSSI_THRESHOLD) \
|
||
CFG(CFG_BT_LOW_RSSI_THRESHOLD) \
|
||
CFG(CFG_BT_INTERFERENCE_LOW_LL) \
|
||
CFG(CFG_BT_INTERFERENCE_LOW_UL) \
|
||
CFG(CFG_BT_INTERFERENCE_MEDIUM_LL) \
|
||
CFG(CFG_BT_INTERFERENCE_MEDIUM_UL) \
|
||
CFG(CFG_BT_INTERFERENCE_HIGH_LL) \
|
||
CFG(CFG_BT_INTERFERENCE_HIGH_UL) \
|
||
COEX_MPTA_HELPER_CFG \
|
||
CFG(CFG_BT_SCO_ALLOW_WLAN_2G_SCAN) \
|
||
THREE_WAY_COEX_CONFIG_LEGACY_CFG \
|
||
SET_INIT_CHAIN_MODE_FOR_BTC_CFG \
|
||
CFG(CFG_BLE_SCAN_COEX_POLICY) \
|
||
TPUT_SHAPING_ENABLE_CFG
|
||
#endif
|