android_kernel_samsung_sm8650-modules/fw/htt.h

/*
 * Copyright (c) 2011-2021 The Linux Foundation. All rights reserved.
 *
 * Previously licensed under the ISC license by Qualcomm Atheros, Inc.
 *
 *
 * Permission to use, copy, modify, and/or distribute this software for
 * any purpose with or without fee is hereby granted, provided that the
 * above copyright notice and this permission notice appear in all
 * copies.
 *
 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
 * WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE
 * AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL
 * DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
 * PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
 * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
 * PERFORMANCE OF THIS SOFTWARE.
 */

/*
 * This file was originally distributed by Qualcomm Atheros, Inc.
 * under proprietary terms before Copyright ownership was assigned
 * to the Linux Foundation.
 */

/**
 * @file htt.h
 *
 * @details the public header file of HTT layer
 */

#ifndef _HTT_H_
#define _HTT_H_

#include <htt_deps.h>
#include <htt_common.h>

/*
 * Unless explicitly specified to use 64 bits to represent physical addresses
 * (or more precisely, bus addresses), default to 32 bits.
 */
#ifndef HTT_PADDR64
    #define HTT_PADDR64 0
#endif

#ifndef offsetof
#define offsetof(type, field)   ((unsigned int)(&((type *)0)->field))
#endif

/*
 * HTT version history:
 * 1.0  initial numbered version
 * 1.1  modifications to STATS messages.
 *      These modifications are not backwards compatible, but since the
 *      STATS messages themselves are non-essential (they are for debugging),
 *      the 1.1 version of the HTT message library as a whole is compatible
 *      with the 1.0 version.
 * 1.2  reset mask IE added to STATS_REQ message
 * 1.3  stat config IE added to STATS_REQ message
 *----
 * 2.0  FW rx PPDU desc added to RX_IND message
 * 2.1  Enable msdu_ext/frag_desc banking change for WIFI2.0
 *----
 * 3.0  Remove HTT_H2T_MSG_TYPE_MGMT_TX message
 * 3.1  Added HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND message
 * 3.2  Added HTT_H2T_MSG_TYPE_WDI_IPA_CFG,
 *            HTT_H2T_MSG_TYPE_WDI_IPA_OP_REQUEST messages
 * 3.3  Added HTT_H2T_MSG_TYPE_AGGR_CFG_EX message
 * 3.4  Added tx_compl_req flag in HTT tx descriptor
 * 3.5  Added flush and fail stats in rx_reorder stats structure
 * 3.6  Added frag flag in HTT RX INORDER PADDR IND header
 * 3.7  Made changes to support EOS Mac_core 3.0
 * 3.8  Added txq_group information element definition;
 *      added optional txq_group suffix to TX_CREDIT_UPDATE_IND message
 * 3.9  Added HTT_T2H CHAN_CHANGE message;
 *      Allow buffer addresses in bus-address format to be stored as
 *      either 32 bits or 64 bits.
 * 3.10 Add optional TLV extensions to the VERSION_REQ and VERSION_CONF
 *      messages to specify which HTT options to use.
 *      Initial TLV options cover:
 *        - whether to use 32 or 64 bits to represent LL bus addresses
 *        - whether to use TX_COMPL_IND or TX_CREDIT_UPDATE_IND in HL systems
 *        - how many tx queue groups to use
 * 3.11 Expand rx debug stats:
 *        - Expand the rx_reorder_stats struct with stats about successful and
 *          failed rx buffer allcoations.
 *        - Add a new rx_remote_buffer_mgmt_stats struct with stats about
 *          the supply, allocation, use, and recycling of rx buffers for the
 *          "remote ring" of rx buffers in host member in LL systems.
 *          Add RX_REMOTE_RING_BUFFER_INFO stats type for uploading these stats.
 * 3.12 Add "rx offload packet error" message with initial "MIC error" subtype
 * 3.13 Add constants + macros to support 64-bit address format for the
 *      tx fragments descriptor, the rx ring buffer, and the rx ring
 *      index shadow register.
 * 3.14 Add a method for the host to provide detailed per-frame tx specs:
 *        - Add htt_tx_msdu_desc_ext_t struct def.
 *        - Add TLV to specify whether the target supports the HTT tx MSDU
 *          extension descriptor.
 *        - Change a reserved bit in the HTT tx MSDU descriptor to an
 *          "extension" bit, to specify whether a HTT tx MSDU extension
 *          descriptor is present.
 * 3.15 Add HW rx desc info to per-MSDU info elems in RX_IN_ORD_PADDR_IND msg.
 *      (This allows the host to obtain key information about the MSDU
 *      from a memory location already in the cache, rather than taking a
 *      cache miss for each MSDU by reading the HW rx descs.)
 * 3.16 Add htt_pkt_type_eth2 and define pkt_subtype flags to indicate
 *      whether a copy-engine classification result is appended to TX_FRM.
 * 3.17 Add a version of the WDI_IPA_CFG message; add RX_RING2 to WDI_IPA_CFG
 * 3.18 Add a PEER_DEL tx completion indication status, for HL cleanup of
 *      tx frames in the target after the peer has already been deleted.
 * 3.19 Add HTT_DBG_STATS_RX_RATE_INFO_V2 and HTT_DBG_STATS_TX_RATE_INFO_V2
 * 3.20 Expand rx_reorder_stats.
 * 3.21 Add optional rx channel spec to HL RX_IND.
 * 3.22 Expand rx_reorder_stats
 *      (distinguish duplicates within vs. outside block ack window)
 * 3.23 Add HTT_T2H_MSG_TYPE_RATE_REPORT to report peer justified rate.
 *      The justified rate is calculated by two steps. The first is to multiply
 *      user-rate by (1 - PER) and the other is to smooth the step 1's result
 *      by a low pass filter.
 *      This change allows HL download scheduling to consider the WLAN rate
 *      that will be used for transmitting the downloaded frames.
 * 3.24 Expand rx_reorder_stats
 *      (add counter for decrypt / MIC errors)
 * 3.25 Expand rx_reorder_stats
 *      (add counter of frames received into both local + remote rings)
 * 3.26 Add stats struct for counting rx of tx BF, MU, SU, and NDPA frames
 *      (HTT_DBG_STATS_TXBF_MUSU_NDPA_PKT, rx_txbf_musu_ndpa_pkts_stats)
 * 3.27 Add a new interface for flow-control. The following t2h messages have
 *      been included: HTT_T2H_MSG_TYPE_FLOW_POOL_MAP and
 *      HTT_T2H_MSG_TYPE_FLOW_POOL_UNMAP
 * 3.28 Add a new interface for ring interface change. The following two h2t
 *      and one t2h messages have been included:
 *      HTT_H2T_MSG_TYPE_SRING_SETUP, HTT_H2T_MSG_TYPE_RX_RING_SELECTION_CFG,
 *      and HTT_T2H_MSG_TYPE_SRING_SETUP_DONE
 * 3.29 Add definitions of htt_tx_msdu_desc_ext2_t descriptor and other
 *      information elements passed from the host to a Lithium target,
 *      Add definitions of the HTT_H2T ADD_WDS_ENTRY and DELETE_WDS_ENTRY
 *      messages and the HTT_T2H MAP_FLOW_INFO message (for use with Lithium
 *      targets).
 * 3.30 Add pktlog flag inside HTT_T2H RX_IN_ORD_PADDR_IND message
 * 3.31 Add HTT_H2T_MSG_TYPE_RFS_CONFIG
 * 3.32 Add HTT_WDI_IPA_OPCODE_SHARING_STATS, HTT_WDI_IPA_OPCODE_SET_QUOTA and
 *      HTT_WDI_IPA_OPCODE_IND_QUOTA for getting quota and reporting WiFi
 *      sharing stats
 * 3.33 Add HTT_TX_COMPL_IND_STAT_DROP and HTT_TX_COMPL_IND_STAT_HOST_INSPECT
 * 3.34 Add HW_PEER_ID field to PEER_MAP
 * 3.35 Revise bitfield defs of HTT_SRING_SETUP message
 *      (changes are not backwards compatible, but HTT_SRING_SETUP message is
 *      not yet in use)
 * 3.36 Add HTT_H2T_MSG_TYPE_EXT_STATS_REQ and HTT_T2H_MSG_TYPE_EXT_STATS_CONF
 * 3.37 Add HTT_PEER_TYPE and htt_mac_addr defs
 * 3.38 Add holes_no_filled field to rx_reorder_stats
 * 3.39 Add host_inspected flag to htt_tx_tcl_vdev_metadata
 * 3.40 Add optional timestamps in the HTT tx completion
 * 3.41 Add optional tx power spec in the HTT tx completion (for DSRC use)
 * 3.42 Add PPDU_STATS_CFG + PPDU_STATS_IND
 * 3.43 Add HTT_STATS_RX_PDEV_FW_STATS_PHY_ERR defs
 * 3.44 Add htt_tx_wbm_completion_v2
 * 3.45 Add host_tx_desc_pool flag in htt_tx_msdu_desc_ext2_t
 * 3.46 Add MAC ID and payload size fields to HTT_T2H_MSG_TYPE_PKTLOG header
 * 3.47 Add HTT_T2H PEER_MAP_V2 and PEER_UNMAP_V2
 * 3.48 Add pdev ID field to HTT_T2H_MSG_TYPE_PPDU_STATS_IND and
 *      HTT_T2H_MSG_TYPE_PKTLOG
 * 3.49 Add HTT_T2H_MSG_TYPE_MONITOR_MAC_HEADER_IND def
 * 3.50 Add learning_frame flag to htt_tx_msdu_desc_ext2_t
 * 3.51 Add SW peer ID and TID num to HTT TX WBM COMPLETION
 * 3.52 Add HTT_T2H FLOW_POOL_RESIZE msg def
 * 3.53 Update HTT_T2H FLOW_POOL_RESIZE msg def
 * 3.54 Define mcast and mcast_valid flags within htt_tx_wbm_transmit_status
 * 3.55 Add initiator / responder flags to RX_DELBA indication
 * 3.56 Fix HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE bit-mask defs
 * 3.57 Add support for in-band data within HTT_T2H_MSG_TYPE_CFR_DUMP_COMPL_IND
 * 3.58 Add optional MSDU ack RSSI array to end of HTT_T2H TX_COMPL_IND msg
 * 3.59 Add HTT_RXDMA_HOST_BUF_RING2 def
 * 3.60 Add HTT_T2H_MSG_TYPE_PEER_STATS_IND def
 * 3.61 Add rx offset fields to HTT_H2T_MSG_TYPE_RX_RING_SELECTION_CFG msg
 * 3.62 Add antenna mask to reserved space in htt_rx_ppdu_desc_t
 * 3.63 Add HTT_HTT_T2H_MSG_TYPE_BKPRESSURE_EVENT_IND def
 * 3.64 Add struct htt_tx_compl_ind_append_tx_tsf64 and add tx_tsf64
 *      array to the end of HTT_T2H TX_COMPL_IND msg
 * 3.65 Add fields in htt_tx_msdu_desc_ext2_t to allow the host to provide
 *      a "cookie" to identify a MSDU, and to specify to not apply aggregation
 *      for a MSDU.
 * 3.66 Add HTT_T2H_MSG_TYPE_TX_OFFLOAD_DELIVER_IND msg.
 *      Add PKT_CAPTURE_MODE flag within HTT_T2H TX_I_ORD_PADDR_IND msg.
 * 3.67 Add drop threshold field to HTT_H2T RX_RING_SELECTION_CFG msg.
 * 3.68 Add ipa_drop threshold fields to HTT_H2T_MSG_TYPE_SRING_SETUP
 * 3.69 Add htt_ul_ofdma_user_info_v0 defs
 * 3.70 Add AST1-AST3 fields to HTT_T2H PEER_MAP_V2 msg
 * 3.71 Add rx offload engine / flow search engine htt setup message defs for
 *      HTT_H2T_MSG_TYPE_RX_FSE_SETUP_CFG, HTT_H2T_MSG_TYPE_RX_FSE_OPERATION_CFG
 * 3.72 Add tx_retry_cnt fields to htt_tx_offload_deliver_ind_hdr_t and
 *      htt_tx_data_hdr_information
 * 3.73 Add channel pre-calibration data upload and download messages defs for
 *      HTT_T2H_MSG_TYPE_CHAN_CALDATA and HTT_H2T_MSG_TYPE_CHAN_CALDATA
 * 3.74 Add HTT_T2H_MSG_TYPE_RX_FISA_CFG msg.
 * 3.75 Add fp_ndp and mo_ndp flags in HTT_H2T_MSG_TYPE_RX_RING_SELECTION_CFG.
 * 3.76 Add HTT_H2T_MSG_TYPE_3_TUPLE_HASH_CFG msg.
 * 3.77 Add HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE msg.
 * 3.78 Add htt_ppdu_id def.
 * 3.79 Add HTT_NUM_AC_WMM def.
 * 3.80 Add add WDS_FREE_COUNT bitfield in T2H PEER_UNMAP_V2 msg.
 * 3.81 Add ppdu_start_tsf field in HTT_TX_WBM_COMPLETION_V2.
 * 3.82 Add WIN_SIZE field to HTT_T2H_MSG_TYPE_RX_DELBA msg.
 * 3.83 Shrink seq_idx field in HTT PPDU ID from 3 bits to 2.
 * 3.84 Add fisa_control_bits_v2 def.
 * 3.85 Add HTT_RX_PEER_META_DATA defs.
 * 3.86 Add HTT_T2H_MSG_TYPE_FSE_CMEM_BASE_SEND def.
 * 3.87 Add on-chip AST index field to PEER_MAP_V2 msg.
 * 3.88 Add HTT_H2T_MSG_TYPE_HOST_PADDR_SIZE def.
 * 3.89 Add MSDU queue enumerations.
 * 3.90 Add HTT_T2H_MSG_TYPE_MLO_TIMESTAMP_OFFSET_IND def.
 * 3.91 Add HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP, _UNMAP defs.
 * 3.92 Add HTT_H2T_MSG_TYPE_RXDMA_RXOLE_PPE_CFG def.
 * 3.93 Add HTT_T2H_MSG_TYPE_PEER_MAP_V3 def.
 * 3.94 Add HTT_H2T_MSG_TYPE_VDEVS_TXRX_STATS_CFG,
 *      HTT_T2H_MSG_TYPE_VDEVS_TXRX_STATS_PERIODIC_IND defs.
 */
#define HTT_CURRENT_VERSION_MAJOR 3
#define HTT_CURRENT_VERSION_MINOR 94

#define HTT_NUM_TX_FRAG_DESC  1024

#define HTT_WIFI_IP_VERSION(x,y) ((x) == (y))

#define HTT_CHECK_SET_VAL(field, val) \
    A_ASSERT(!((val) & ~((field ## _M) >> (field ## _S))))

/* macros to assist in sign-extending fields from HTT messages */
#define HTT_SIGN_BIT_MASK(field) \
    ((field ## _M + (1 << field ## _S)) >> 1)
#define HTT_SIGN_BIT(_val, field) \
    (_val & HTT_SIGN_BIT_MASK(field))
#define HTT_SIGN_BIT_UNSHIFTED(_val, field) \
    (HTT_SIGN_BIT(_val, field) >> field ## _S)
#define HTT_SIGN_BIT_UNSHIFTED_MINUS_ONE(_val, field) \
    (HTT_SIGN_BIT_UNSHIFTED(_val, field) - 1)
#define HTT_SIGN_BIT_EXTENSION(_val, field) \
    (~(HTT_SIGN_BIT_UNSHIFTED(_val, field) | \
    HTT_SIGN_BIT_UNSHIFTED_MINUS_ONE(_val, field)))
#define HTT_SIGN_BIT_EXTENSION_MASK(_val, field) \
    (HTT_SIGN_BIT_EXTENSION(_val, field) & ~(field ## _M >> field ## _S))


/*
 * TEMPORARY:
 * Provide HTT_H2T_MSG_TYPE_MGMT_TX as an alias for
 * DEPRECATED_HTT_H2T_MSG_TYPE_MGMT_TX until all code
 * that refers to HTT_H2T_MSG_TYPE_MGMT_TX has been
 * updated.
 */
#define HTT_H2T_MSG_TYPE_MGMT_TX DEPRECATED_HTT_H2T_MSG_TYPE_MGMT_TX

/*
 * TEMPORARY:
 * Provide HTT_T2H_MSG_TYPE_RC_UPDATE_IND as an alias for
 * DEPRECATED_HTT_T2H_MSG_TYPE_RC_UPDATE_IND until all code
 * that refers to HTT_T2H_MSG_TYPE_RC_UPDATE_IND has been
 * updated.
 */
#define HTT_T2H_MSG_TYPE_RC_UPDATE_IND DEPRECATED_HTT_T2H_MSG_TYPE_RC_UPDATE_IND

/*
 * htt_dbg_stats_type -
 * bit positions for each stats type within a stats type bitmask
 * The bitmask contains 24 bits.
 */
enum htt_dbg_stats_type {
    HTT_DBG_STATS_WAL_PDEV_TXRX              =  0, /* bit 0  ->    0x1 */
    HTT_DBG_STATS_RX_REORDER                 =  1, /* bit 1  ->    0x2 */
    HTT_DBG_STATS_RX_RATE_INFO               =  2, /* bit 2  ->    0x4 */
    HTT_DBG_STATS_TX_PPDU_LOG                =  3, /* bit 3  ->    0x8 */
    HTT_DBG_STATS_TX_RATE_INFO               =  4, /* bit 4  ->   0x10 */
    HTT_DBG_STATS_TIDQ                       =  5, /* bit 5  ->   0x20 */
    HTT_DBG_STATS_TXBF_INFO                  =  6, /* bit 6  ->   0x40 */
    HTT_DBG_STATS_SND_INFO                   =  7, /* bit 7  ->   0x80 */
    HTT_DBG_STATS_ERROR_INFO                 =  8, /* bit 8  ->  0x100 */
    HTT_DBG_STATS_TX_SELFGEN_INFO            =  9, /* bit 9  ->  0x200 */
    HTT_DBG_STATS_TX_MU_INFO                 = 10, /* bit 10 ->  0x400 */
    HTT_DBG_STATS_SIFS_RESP_INFO             = 11, /* bit 11 ->  0x800 */
    HTT_DBG_STATS_RX_REMOTE_RING_BUFFER_INFO = 12, /* bit 12 -> 0x1000 */
    HTT_DBG_STATS_RX_RATE_INFO_V2            = 13, /* bit 13 -> 0x2000 */
    HTT_DBG_STATS_TX_RATE_INFO_V2            = 14, /* bit 14 -> 0x4000 */
    HTT_DBG_STATS_TXBF_MUSU_NDPA_PKT         = 15, /* bit 15 -> 0x8000 */
    /* bits 16-23 currently reserved */

    /* keep this last */
    HTT_DBG_NUM_STATS
};

/*=== HTT option selection TLVs ===
 * Certain HTT messages have alternatives or options.
 * For such cases, the host and target need to agree on which option to use.
 * Option specification TLVs can be appended to the VERSION_REQ and
 * VERSION_CONF messages to select options other than the default.
 * These TLVs are entirely optional - if they are not provided, there is a
 * well-defined default for each option.  If they are provided, they can be
 * provided in any order.  Each TLV can be present or absent independent of
 * the presence / absence of other TLVs.
 *
 * The HTT option selection TLVs use the following format:
 *     |31                             16|15             8|7              0|
 *     |---------------------------------+----------------+----------------|
 *     |        value (payload)          |     length     |       tag      |
 *     |-------------------------------------------------------------------|
 * The value portion need not be only 2 bytes; it can be extended by any
 * integer number of 4-byte units.  The total length of the TLV, including
 * the tag and length fields, must be a multiple of 4 bytes.  The length
 * field specifies the total TLV size in 4-byte units.  Thus, the typical
 * TLV, with a 1-byte tag field, a 1-byte length field, and a 2-byte value
 * field, would store 0x1 in its length field, to show that the TLV occupies
 * a single 4-byte unit.
 */

/*--- TLV header format - applies to all HTT option TLVs ---*/

enum HTT_OPTION_TLV_TAGS {
    HTT_OPTION_TLV_TAG_RESERVED0                = 0x0,
    HTT_OPTION_TLV_TAG_LL_BUS_ADDR_SIZE         = 0x1,
    HTT_OPTION_TLV_TAG_HL_SUPPRESS_TX_COMPL_IND = 0x2,
    HTT_OPTION_TLV_TAG_MAX_TX_QUEUE_GROUPS      = 0x3,
    HTT_OPTION_TLV_TAG_SUPPORT_TX_MSDU_DESC_EXT = 0x4,
};

PREPACK struct htt_option_tlv_header_t {
    A_UINT8 tag;
    A_UINT8 length;
} POSTPACK;

#define HTT_OPTION_TLV_TAG_M      0x000000ff
#define HTT_OPTION_TLV_TAG_S      0
#define HTT_OPTION_TLV_LENGTH_M   0x0000ff00
#define HTT_OPTION_TLV_LENGTH_S   8
/*
 * value0 - 16 bit value field stored in word0
 * The TLV's value field may be longer than 2 bytes, in which case
 * the remainder of the value is stored in word1, word2, etc.
 */
#define HTT_OPTION_TLV_VALUE0_M   0xffff0000
#define HTT_OPTION_TLV_VALUE0_S   16

#define HTT_OPTION_TLV_TAG_SET(word, tag)           \
    do {                                            \
        HTT_CHECK_SET_VAL(HTT_OPTION_TLV_TAG, tag); \
        (word) |= ((tag) << HTT_OPTION_TLV_TAG_S);  \
    } while (0)
#define HTT_OPTION_TLV_TAG_GET(word) \
    (((word) & HTT_OPTION_TLV_TAG_M) >> HTT_OPTION_TLV_TAG_S)

#define HTT_OPTION_TLV_LENGTH_SET(word, tag)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_OPTION_TLV_LENGTH, tag); \
        (word) |= ((tag) << HTT_OPTION_TLV_LENGTH_S);  \
    } while (0)
#define HTT_OPTION_TLV_LENGTH_GET(word) \
    (((word) & HTT_OPTION_TLV_LENGTH_M) >> HTT_OPTION_TLV_LENGTH_S)

#define HTT_OPTION_TLV_VALUE0_SET(word, tag)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_OPTION_TLV_VALUE0, tag); \
        (word) |= ((tag) << HTT_OPTION_TLV_VALUE0_S);  \
    } while (0)
#define HTT_OPTION_TLV_VALUE0_GET(word) \
    (((word) & HTT_OPTION_TLV_VALUE0_M) >> HTT_OPTION_TLV_VALUE0_S)

/*--- format of specific HTT option TLVs ---*/

/*
 * HTT option TLV for specifying LL bus address size
 * Some chips require bus addresses used by the target to access buffers
 * within the host's memory to be 32 bits; others require bus addresses
 * used by the target to access buffers within the host's memory to be
 * 64 bits.
 * The LL_BUS_ADDR_SIZE TLV can be sent from the target to the host as
 * a suffix to the VERSION_CONF message to specify which bus address format
 * the target requires.
 * If this LL_BUS_ADDR_SIZE TLV is not sent by the target, the host should
 * default to providing bus addresses to the target in 32-bit format.
 */
enum HTT_OPTION_TLV_LL_BUS_ADDR_SIZE_VALUES {
    HTT_OPTION_TLV_LL_BUS_ADDR_SIZE32 = 0x0,
    HTT_OPTION_TLV_LL_BUS_ADDR_SIZE64 = 0x1,
};
PREPACK struct htt_option_tlv_ll_bus_addr_size_t {
    struct htt_option_tlv_header_t hdr;
    A_UINT16 ll_bus_addr_size; /* LL_BUS_ADDR_SIZE_VALUES enum */
} POSTPACK;

/*
 * HTT option TLV for specifying whether HL systems should indicate
 * over-the-air tx completion for individual frames, or should instead
 * send a bulk TX_CREDIT_UPDATE_IND except when the host explicitly
 * requests an OTA tx completion for a particular tx frame.
 * This option does not apply to LL systems, where the TX_COMPL_IND
 * is mandatory.
 * This option is primarily intended for HL systems in which the tx frame
 * downloads over the host --> target bus are as slow as or slower than
 * the transmissions over the WLAN PHY.  For cases where the bus is faster
 * than the WLAN PHY, the target will transmit relatively large A-MPDUs,
 * and consquently will send one TX_COMPL_IND message that covers several
 * tx frames.  For cases where the WLAN PHY is faster than the bus,
 * the target will end up transmitting very short A-MPDUs, and consequently
 * sending many TX_COMPL_IND messages, which each cover a very small number
 * of tx frames.
 * The HL_SUPPRESS_TX_COMPL_IND TLV can be sent by the host to the target as
 * a suffix to the VERSION_REQ message to request whether the host desires to
 * use TX_CREDIT_UPDATE_IND rather than TX_COMPL_IND.  The target can then
 * send a HTT_SUPPRESS_TX_COMPL_IND TLV to the host as a suffix to the
 * VERSION_CONF message to confirm whether TX_CREDIT_UPDATE_IND will be used
 * rather than TX_COMPL_IND.  TX_CREDIT_UPDATE_IND shall only be used if the
 * host sends a HL_SUPPRESS_TX_COMPL_IND TLV requesting use of
 * TX_CREDIT_UPDATE_IND, and the target sends a HL_SUPPRESS_TX_COMPLE_IND TLV
 * back to the host confirming use of TX_CREDIT_UPDATE_IND.
 * Lack of a HL_SUPPRESS_TX_COMPL_IND TLV from either host --> target or
 * target --> host is equivalent to a HL_SUPPRESS_TX_COMPL_IND that
 * explicitly specifies HL_ALLOW_TX_COMPL_IND in the value payload of the
 * TLV.
 */
enum HTT_OPTION_TLV_HL_SUPPRESS_TX_COMPL_IND_VALUES {
    HTT_OPTION_TLV_HL_ALLOW_TX_COMPL_IND = 0x0,
    HTT_OPTION_TLV_HL_SUPPRESS_TX_COMPL_IND = 0x1,
};
PREPACK struct htt_option_tlv_hl_suppress_tx_compl_ind_t {
    struct htt_option_tlv_header_t hdr;
    A_UINT16 hl_suppress_tx_compl_ind; /* HL_SUPPRESS_TX_COMPL_IND enum */
} POSTPACK;

/*
 * HTT option TLV for specifying how many tx queue groups the target
 * may establish.
 * This TLV specifies the maximum value the target may send in the
 * txq_group_id field of any TXQ_GROUP information elements sent by
 * the target to the host.  This allows the host to pre-allocate an
 * appropriate number of tx queue group structs.
 *
 * The MAX_TX_QUEUE_GROUPS_TLV can be sent from the host to the target as
 * a suffix to the VERSION_REQ message to specify whether the host supports
 * tx queue groups at all, and if so if there is any limit on the number of
 * tx queue groups that the host supports.
 * The MAX_TX_QUEUE_GROUPS TLV can be sent from the target to the host as
 * a suffix to the VERSION_CONF message.  If the host has specified in the
 * VER_REQ message a limit on the number of tx queue groups the host can
 * supprt, the target shall limit its specification of the maximum tx groups
 * to be no larger than this host-specified limit.
 *
 * If the target does not provide a MAX_TX_QUEUE_GROUPS TLV, then the host
 * shall preallocate 4 tx queue group structs, and the target shall not
 * specify a txq_group_id larger than 3.
 */
enum HTT_OPTION_TLV_MAX_TX_QUEUE_GROUPS_VALUES {
    HTT_OPTION_TLV_TX_QUEUE_GROUPS_UNSUPPORTED = 0,
    /*
     * values 1 through N specify the max number of tx queue groups
     * the sender supports
     */
    HTT_OPTION_TLV_TX_QUEUE_GROUPS_UNLIMITED = 0xffff,
};
/* TEMPORARY backwards-compatibility alias for a typo fix -
 * The htt_option_tlv_mac_tx_queue_groups_t typo has been corrected
 * to  htt_option_tlv_max_tx_queue_groups_t, but an alias is provided
 * to support the old name (with the typo) until all references to the
 * old name are replaced with the new name.
 */
#define htt_option_tlv_mac_tx_queue_groups_t htt_option_tlv_max_tx_queue_groups_t
PREPACK struct htt_option_tlv_max_tx_queue_groups_t {
    struct htt_option_tlv_header_t hdr;
    A_UINT16 max_tx_queue_groups; /* max txq_group_id + 1 */
} POSTPACK;

/*
 * HTT option TLV for specifying whether the target supports an extended
 * version of the HTT tx descriptor.  If the target provides this TLV
 * and specifies in the TLV that the target supports an extended version
 * of the HTT tx descriptor, the target must check the "extension" bit in
 * the HTT tx descriptor, and if the extension bit is set, to expect a
 * HTT tx MSDU extension descriptor immediately following the HTT tx MSDU
 * descriptor.  Furthermore, the target must provide room for the HTT
 * tx MSDU extension descriptor in the target's TX_FRM buffer.
 * This option is intended for systems where the host needs to explicitly
 * control the transmission parameters such as tx power for individual
 * tx frames.
 * The SUPPORT_TX_MSDU_DESC_EXT TLB can be sent by the target to the host
 * as a suffix to the VERSION_CONF message to explicitly specify whether
 * the target supports the HTT tx MSDU extension descriptor.
 * Lack of a SUPPORT_TX_MSDU_DESC_EXT from the target shall be interpreted
 * by the host as lack of target support for the HTT tx MSDU extension
 * descriptor; the host shall provide HTT tx MSDU extension descriptors in
 * the HTT_H2T TX_FRM messages only if the target indicates it supports
 * the HTT tx MSDU extension descriptor.
 * The host is not required to provide the HTT tx MSDU extension descriptor
 * just because the target supports it; the target must check the
 * "extension" bit in the HTT tx MSDU descriptor to determine whether an
 * extension descriptor is present.
 */
enum HTT_OPTION_TLV_SUPPORT_TX_MSDU_DESC_EXT_VALUES {
    HTT_OPTION_TLV_TX_MSDU_DESC_EXT_NO_SUPPORT = 0x0,
    HTT_OPTION_TLV_TX_MSDU_DESC_EXT_SUPPORT = 0x1,
};
PREPACK struct htt_option_tlv_support_tx_msdu_desc_ext_t {
    struct htt_option_tlv_header_t hdr;
    A_UINT16 tx_msdu_desc_ext_support; /* SUPPORT_TX_MSDU_DESC_EXT enum */
} POSTPACK;

typedef struct {
    union {
        /* BIT [11 :  0]   :- tag
         * BIT [23 : 12]   :- length
         * BIT [31 : 24]   :- reserved
         */
        A_UINT32 tag__length;
        /*
         * The following struct is not endian-portable.
         * It is suitable for use within the target, which is known to be
         * little-endian.
         * The host should use the above endian-portable macros to access
         * the tag and length bitfields in an endian-neutral manner.
         */
        struct {
            A_UINT32 tag      :      12, /* BIT [11 :  0] */
                     length   :   12,    /* BIT [23 : 12] */
                     reserved :  8;      /* BIT [31 : 24] */
        };
    };
} htt_tlv_hdr_t;

typedef enum {
    HTT_STATS_TX_PDEV_CMN_TAG                      = 0,  /* htt_tx_pdev_stats_cmn_tlv */
    HTT_STATS_TX_PDEV_UNDERRUN_TAG                 = 1,  /* htt_tx_pdev_stats_urrn_tlv_v */
    HTT_STATS_TX_PDEV_SIFS_TAG                     = 2,  /* htt_tx_pdev_stats_sifs_tlv_v */
    HTT_STATS_TX_PDEV_FLUSH_TAG                    = 3,  /* htt_tx_pdev_stats_flush_tlv_v */
    HTT_STATS_TX_PDEV_PHY_ERR_TAG                  = 4,  /* htt_tx_pdev_stats_phy_err_tlv_v */
    HTT_STATS_STRING_TAG = 5,                            /* htt_stats_string_tlv */
    HTT_STATS_TX_HWQ_CMN_TAG = 6,                        /* htt_tx_hwq_stats_cmn_tlv */
    HTT_STATS_TX_HWQ_DIFS_LATENCY_TAG              = 7,  /* htt_tx_hwq_difs_latency_stats_tlv_v */
    HTT_STATS_TX_HWQ_CMD_RESULT_TAG                = 8,  /* htt_tx_hwq_cmd_result_stats_tlv_v */
    HTT_STATS_TX_HWQ_CMD_STALL_TAG                 = 9,  /* htt_tx_hwq_cmd_stall_stats_tlv_v */
    HTT_STATS_TX_HWQ_FES_STATUS_TAG                = 10, /* htt_tx_hwq_fes_result_stats_tlv_v */
    HTT_STATS_TX_TQM_GEN_MPDU_TAG                  = 11, /* htt_tx_tqm_gen_mpdu_stats_tlv_v */
    HTT_STATS_TX_TQM_LIST_MPDU_TAG                 = 12, /* htt_tx_tqm_list_mpdu_stats_tlv_v */
    HTT_STATS_TX_TQM_LIST_MPDU_CNT_TAG             = 13, /* htt_tx_tqm_list_mpdu_cnt_tlv_v */
    HTT_STATS_TX_TQM_CMN_TAG = 14,                       /* htt_tx_tqm_cmn_stats_tlv */
    HTT_STATS_TX_TQM_PDEV_TAG                      = 15, /* htt_tx_tqm_pdev_stats_tlv_v */
    HTT_STATS_TX_TQM_CMDQ_STATUS_TAG               = 16, /* htt_tx_tqm_cmdq_status_tlv */
    HTT_STATS_TX_DE_EAPOL_PACKETS_TAG              = 17, /* htt_tx_de_eapol_packets_stats_tlv */
    HTT_STATS_TX_DE_CLASSIFY_FAILED_TAG            = 18, /* htt_tx_de_classify_failed_stats_tlv */
    HTT_STATS_TX_DE_CLASSIFY_STATS_TAG             = 19, /* htt_tx_de_classify_stats_tlv */
    HTT_STATS_TX_DE_CLASSIFY_STATUS_TAG            = 20, /* htt_tx_de_classify_status_stats_tlv */
    HTT_STATS_TX_DE_ENQUEUE_PACKETS_TAG            = 21, /* htt_tx_de_enqueue_packets_stats_tlv */
    HTT_STATS_TX_DE_ENQUEUE_DISCARD_TAG            = 22, /* htt_tx_de_enqueue_discard_stats_tlv */
    HTT_STATS_TX_DE_CMN_TAG = 23,                        /* htt_tx_de_cmn_stats_tlv */
    HTT_STATS_RING_IF_TAG = 24,                          /* htt_ring_if_stats_tlv */
    HTT_STATS_TX_PDEV_MU_MIMO_STATS_TAG            = 25, /* htt_tx_pdev_mu_mimo_sch_stats_tlv */
    HTT_STATS_SFM_CMN_TAG = 26,                          /* htt_sfm_cmn_tlv */
    HTT_STATS_SRING_STATS_TAG                      = 27, /* htt_sring_stats_tlv */
    HTT_STATS_RX_PDEV_FW_STATS_TAG                 = 28, /* htt_rx_pdev_fw_stats_tlv */
    HTT_STATS_RX_PDEV_FW_RING_MPDU_ERR_TAG         = 29, /* htt_rx_pdev_fw_ring_mpdu_err_tlv_v */
    HTT_STATS_RX_PDEV_FW_MPDU_DROP_TAG             = 30, /* htt_rx_pdev_fw_mpdu_drop_tlv_v */
    HTT_STATS_RX_SOC_FW_STATS_TAG                  = 31, /* htt_rx_soc_fw_stats_tlv */
    HTT_STATS_RX_SOC_FW_REFILL_RING_EMPTY_TAG      = 32, /* htt_rx_soc_fw_refill_ring_empty_tlv_v */
    HTT_STATS_RX_SOC_FW_REFILL_RING_NUM_REFILL_TAG = 33, /* htt_rx_soc_fw_refill_ring_num_refill_tlv_v */
    HTT_STATS_TX_PDEV_RATE_STATS_TAG               = 34, /* htt_tx_pdev_rate_stats_tlv */
    HTT_STATS_RX_PDEV_RATE_STATS_TAG               = 35, /* htt_rx_pdev_rate_stats_tlv */
    HTT_STATS_TX_PDEV_SCHEDULER_TXQ_STATS_TAG      = 36, /* htt_tx_pdev_stats_sched_per_txq_tlv */
    HTT_STATS_TX_SCHED_CMN_TAG                     = 37, /* htt_stats_tx_sched_cmn_tlv */
    HTT_STATS_TX_PDEV_MUMIMO_MPDU_STATS_TAG        = 38, /* htt_tx_pdev_mu_mimo_mpdu_stats_tlv */
    HTT_STATS_SCHED_TXQ_CMD_POSTED_TAG             = 39, /* htt_sched_txq_cmd_posted_tlv_v */
    HTT_STATS_RING_IF_CMN_TAG                      = 40, /* htt_ring_if_cmn_tlv */
    HTT_STATS_SFM_CLIENT_USER_TAG                  = 41, /* htt_sfm_client_user_tlv_v */
    HTT_STATS_SFM_CLIENT_TAG = 42,                       /* htt_sfm_client_tlv */
    HTT_STATS_TX_TQM_ERROR_STATS_TAG               = 43, /* htt_tx_tqm_error_stats_tlv */
    HTT_STATS_SCHED_TXQ_CMD_REAPED_TAG             = 44, /* htt_sched_txq_cmd_reaped_tlv_v */
    HTT_STATS_SRING_CMN_TAG = 45,                        /* htt_sring_cmn_tlv */
    HTT_STATS_TX_SELFGEN_AC_ERR_STATS_TAG          = 46, /* htt_tx_selfgen_ac_err_stats_tlv */
    HTT_STATS_TX_SELFGEN_CMN_STATS_TAG             = 47, /* htt_tx_selfgen_cmn_stats_tlv */
    HTT_STATS_TX_SELFGEN_AC_STATS_TAG              = 48, /* htt_tx_selfgen_ac_stats_tlv */
    HTT_STATS_TX_SELFGEN_AX_STATS_TAG              = 49, /* htt_tx_selfgen_ax_stats_tlv */
    HTT_STATS_TX_SELFGEN_AX_ERR_STATS_TAG          = 50, /* htt_tx_selfgen_ax_err_stats_tlv */
    HTT_STATS_TX_HWQ_MUMIMO_SCH_STATS_TAG          = 51, /* htt_tx_hwq_mu_mimo_sch_stats_tlv */
    HTT_STATS_TX_HWQ_MUMIMO_MPDU_STATS_TAG         = 52, /* htt_tx_hwq_mu_mimo_mpdu_stats_tlv */
    HTT_STATS_TX_HWQ_MUMIMO_CMN_STATS_TAG          = 53, /* htt_tx_hwq_mu_mimo_cmn_stats_tlv */
    HTT_STATS_HW_INTR_MISC_TAG                     = 54, /* htt_hw_stats_intr_misc_tlv */
    HTT_STATS_HW_WD_TIMEOUT_TAG                    = 55, /* htt_hw_stats_wd_timeout_tlv */
    HTT_STATS_HW_PDEV_ERRS_TAG                     = 56, /* htt_hw_stats_pdev_errs_tlv */
    HTT_STATS_COUNTER_NAME_TAG                     = 57, /* htt_counter_tlv */
    HTT_STATS_TX_TID_DETAILS_TAG                   = 58, /* htt_tx_tid_stats_tlv */
    HTT_STATS_RX_TID_DETAILS_TAG                   = 59, /* htt_rx_tid_stats_tlv */
    HTT_STATS_PEER_STATS_CMN_TAG                   = 60, /* htt_peer_stats_cmn_tlv */
    HTT_STATS_PEER_DETAILS_TAG                     = 61, /* htt_peer_details_tlv */
    HTT_STATS_PEER_TX_RATE_STATS_TAG               = 62, /* htt_tx_peer_rate_stats_tlv */
    HTT_STATS_PEER_RX_RATE_STATS_TAG               = 63, /* htt_rx_peer_rate_stats_tlv */
    HTT_STATS_PEER_MSDU_FLOWQ_TAG                  = 64, /* htt_msdu_flow_stats_tlv */
    HTT_STATS_TX_DE_COMPL_STATS_TAG                = 65, /* htt_tx_de_compl_stats_tlv */
    HTT_STATS_WHAL_TX_TAG = 66,                          /* htt_hw_stats_whal_tx_tlv */
    HTT_STATS_TX_PDEV_SIFS_HIST_TAG                = 67, /* htt_tx_pdev_stats_sifs_hist_tlv_v */
    HTT_STATS_RX_PDEV_FW_STATS_PHY_ERR_TAG         = 68, /* htt_rx_pdev_fw_stats_phy_err_tlv */
    HTT_STATS_TX_TID_DETAILS_V1_TAG                = 69, /* htt_tx_tid_stats_v1_tlv */
    HTT_STATS_PDEV_CCA_1SEC_HIST_TAG               = 70, /* htt_pdev_cca_stats_hist_tlv (for 1 sec interval stats) */
    HTT_STATS_PDEV_CCA_100MSEC_HIST_TAG            = 71, /* htt_pdev_cca_stats_hist_tlv (for 100 msec interval stats) */
    HTT_STATS_PDEV_CCA_STAT_CUMULATIVE_TAG         = 72, /* htt_pdev_stats_cca_stats_tlv */
    HTT_STATS_PDEV_CCA_COUNTERS_TAG                = 73, /* htt_pdev_stats_cca_counters_tlv */
    HTT_STATS_TX_PDEV_MPDU_STATS_TAG               = 74, /* htt_tx_pdev_mpdu_stats_tlv */
    HTT_STATS_PDEV_TWT_SESSIONS_TAG                = 75, /* htt_pdev_stats_twt_sessions_tlv */
    HTT_STATS_PDEV_TWT_SESSION_TAG                 = 76, /* htt_pdev_stats_twt_session_tlv */
    HTT_STATS_RX_REFILL_RXDMA_ERR_TAG              = 77, /* htt_rx_soc_fw_refill_ring_num_rxdma_err_tlv_v */
    HTT_STATS_RX_REFILL_REO_ERR_TAG                = 78, /* htt_rx_soc_fw_refill_ring_num_reo_err_tlv_v */
    HTT_STATS_RX_REO_RESOURCE_STATS_TAG            = 79, /* htt_rx_reo_debug_stats_tlv_v */
    HTT_STATS_TX_SOUNDING_STATS_TAG                = 80, /* htt_tx_sounding_stats_tlv */
    HTT_STATS_TX_PDEV_TX_PPDU_STATS_TAG            = 81, /* htt_tx_pdev_stats_tx_ppdu_stats_tlv_v */
    HTT_STATS_TX_PDEV_TRIED_MPDU_CNT_HIST_TAG      = 82, /* htt_tx_pdev_stats_tried_mpdu_cnt_hist_tlv_v */
    HTT_STATS_TX_HWQ_TRIED_MPDU_CNT_HIST_TAG       = 83, /* htt_tx_hwq_tried_mpdu_cnt_hist_tlv_v */
    HTT_STATS_TX_HWQ_TXOP_USED_CNT_HIST_TAG        = 84, /* htt_tx_hwq_txop_used_cnt_hist_tlv_v */
    HTT_STATS_TX_DE_FW2WBM_RING_FULL_HIST_TAG      = 85, /* htt_tx_de_fw2wbm_ring_full_hist_tlv */
    HTT_STATS_SCHED_TXQ_SCHED_ORDER_SU_TAG         = 86, /* htt_sched_txq_sched_order_su_tlv */
    HTT_STATS_SCHED_TXQ_SCHED_INELIGIBILITY_TAG    = 87, /* htt_sched_txq_sched_eligibility_tlv */
    HTT_STATS_PDEV_OBSS_PD_TAG                     = 88, /* htt_pdev_obss_pd_stats_tlv */
    HTT_STATS_HW_WAR_TAG                           = 89, /* htt_hw_war_stats_tlv */
    HTT_STATS_RING_BACKPRESSURE_STATS_TAG          = 90, /* htt_ring_backpressure_stats_tlv */
    HTT_STATS_LATENCY_PROF_STATS_TAG               = 91, /* htt_latency_prof_stats_tlv */
    HTT_STATS_LATENCY_CTX_TAG                      = 92, /* htt_latency_prof_ctx_tlv */
    HTT_STATS_LATENCY_CNT_TAG                      = 93, /* htt_latency_prof_cnt_tlv */
    HTT_STATS_RX_PDEV_UL_TRIG_STATS_TAG            = 94, /* htt_rx_pdev_ul_trigger_stats_tlv */
    HTT_STATS_RX_PDEV_UL_OFDMA_USER_STATS_TAG      = 95, /* htt_rx_pdev_ul_ofdma_user_stats_tlv */
    HTT_STATS_RX_PDEV_UL_MIMO_USER_STATS_TAG       = 96, /* htt_rx_pdev_ul_mimo_user_stats_tlv */
    HTT_STATS_RX_PDEV_UL_MUMIMO_TRIG_STATS_TAG     = 97, /* htt_rx_pdev_ul_mumimo_trig_stats_tlv */
    HTT_STATS_RX_FSE_STATS_TAG                     = 98, /* htt_rx_fse_stats_tlv */
    HTT_STATS_PEER_SCHED_STATS_TAG                 = 99, /* htt_peer_sched_stats_tlv */
    HTT_STATS_SCHED_TXQ_SUPERCYCLE_TRIGGER_TAG     = 100, /* htt_sched_txq_supercycle_triggers_tlv_v */
    HTT_STATS_PEER_CTRL_PATH_TXRX_STATS_TAG        = 101, /* htt_peer_ctrl_path_txrx_stats_tlv */
    HTT_STATS_PDEV_CTRL_PATH_TX_STATS_TAG          = 102, /* htt_pdev_ctrl_path_tx_stats_tlv */
    HTT_STATS_RX_PDEV_RATE_EXT_STATS_TAG           = 103, /* htt_rx_pdev_rate_ext_stats_tlv */
    HTT_STATS_TX_PDEV_DL_MU_MIMO_STATS_TAG         = 104, /* htt_tx_pdev_dl_mu_mimo_sch_stats_tlv */
    HTT_STATS_TX_PDEV_UL_MU_MIMO_STATS_TAG         = 105, /* htt_tx_pdev_ul_mu_mimo_sch_stats_tlv */
    HTT_STATS_TX_PDEV_DL_MU_OFDMA_STATS_TAG        = 106, /* htt_tx_pdev_dl_mu_ofdma_sch_stats_tlv */
    HTT_STATS_TX_PDEV_UL_MU_OFDMA_STATS_TAG        = 107, /* htt_tx_pdev_ul_mu_ofdma_sch_stats_tlv */
    HTT_STATS_PDEV_TX_RATE_TXBF_STATS_TAG          = 108, /* htt_tx_peer_rate_txbf_stats_tlv */
    HTT_STATS_UNSUPPORTED_ERROR_STATS_TAG          = 109, /* htt_stats_error_tlv_v */
    HTT_STATS_UNAVAILABLE_ERROR_STATS_TAG          = 110, /* htt_stats_error_tlv_v */
    HTT_STATS_TX_SELFGEN_AC_SCHED_STATUS_STATS_TAG = 111, /* htt_tx_selfgen_ac_sched_status_stats_tlv */
    HTT_STATS_TX_SELFGEN_AX_SCHED_STATUS_STATS_TAG = 112, /* htt_tx_selfgen_ax_sched_status_stats_tlv */
    HTT_STATS_TXBF_OFDMA_NDPA_STATS_TAG            = 113, /* htt_txbf_ofdma_ndpa_stats_tlv */
    HTT_STATS_TXBF_OFDMA_NDP_STATS_TAG             = 114, /* htt_txbf_ofdma_ndp_stats_tlv */
    HTT_STATS_TXBF_OFDMA_BRP_STATS_TAG             = 115, /* htt_txbf_ofdma_brp_stats_tlv */
    HTT_STATS_TXBF_OFDMA_STEER_STATS_TAG           = 116, /* htt_txbf_ofdma_steer_stats_tlv */
    HTT_STATS_STA_UL_OFDMA_STATS_TAG               = 117, /* htt_sta_ul_ofdma_stats_tlv */
    HTT_STATS_VDEV_RTT_RESP_STATS_TAG              = 118, /* htt_vdev_rtt_resp_stats_tlv */
    HTT_STATS_PKTLOG_AND_HTT_RING_STATS_TAG        = 119, /* htt_pktlog_and_htt_ring_stats_tlv */
    HTT_STATS_DLPAGER_STATS_TAG                    = 120, /* htt_dlpager_stats_tlv */
    HTT_STATS_PHY_COUNTERS_TAG                     = 121, /* htt_phy_counters_tlv */
    HTT_STATS_PHY_STATS_TAG                        = 122, /* htt_phy_stats_tlv */
    HTT_STATS_PHY_RESET_COUNTERS_TAG               = 123, /* htt_phy_reset_counters_tlv */
    HTT_STATS_PHY_RESET_STATS_TAG                  = 124, /* htt_phy_reset_stats_tlv */
    HTT_STATS_SOC_TXRX_STATS_COMMON_TAG            = 125, /* htt_t2h_soc_txrx_stats_common_tlv */
    HTT_STATS_VDEV_TXRX_STATS_HW_STATS_TAG         = 126, /* htt_t2h_vdev_txrx_stats_hw_stats_tlv */
    HTT_STATS_VDEV_RTT_INIT_STATS_TAG              = 127, /* htt_vdev_rtt_init_stats_tlv */
    HTT_STATS_PER_RATE_STATS_TAG                   = 128, /* htt_tx_rate_stats_per_tlv */
    HTT_STATS_MU_PPDU_DIST_TAG                     = 129, /* htt_pdev_mu_ppdu_dist_tlv */
    HTT_STATS_TX_PDEV_MUMIMO_GRP_STATS_TAG         = 130, /* htt_tx_pdev_mumimo_grp_stats_tlv */

    HTT_STATS_MAX_TAG,
} htt_tlv_tag_t;

#define HTT_STATS_TLV_TAG_M 0x00000fff
#define HTT_STATS_TLV_TAG_S 0
#define HTT_STATS_TLV_LENGTH_M 0x00fff000
#define HTT_STATS_TLV_LENGTH_S 12

#define HTT_STATS_TLV_TAG_GET(_var) \
    (((_var) & HTT_STATS_TLV_TAG_M) >> \
     HTT_STATS_TLV_TAG_S)

#define HTT_STATS_TLV_TAG_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_STATS_TLV_TAG, _val); \
        ((_var) |= ((_val) << HTT_STATS_TLV_TAG_S)); \
    } while (0)

#define HTT_STATS_TLV_LENGTH_GET(_var) \
    (((_var) & HTT_STATS_TLV_LENGTH_M) >> \
     HTT_STATS_TLV_LENGTH_S)
#define HTT_STATS_TLV_LENGTH_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_STATS_TLV_LENGTH, _val); \
        ((_var) |= ((_val) << HTT_STATS_TLV_LENGTH_S)); \
    } while (0)


/*=== host -> target messages ===============================================*/

enum htt_h2t_msg_type {
    HTT_H2T_MSG_TYPE_VERSION_REQ           = 0x0,
    HTT_H2T_MSG_TYPE_TX_FRM                = 0x1,
    HTT_H2T_MSG_TYPE_RX_RING_CFG           = 0x2,
    HTT_H2T_MSG_TYPE_STATS_REQ             = 0x3,
    HTT_H2T_MSG_TYPE_SYNC                  = 0x4,
    HTT_H2T_MSG_TYPE_AGGR_CFG              = 0x5,
    HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG    = 0x6,
    DEPRECATED_HTT_H2T_MSG_TYPE_MGMT_TX    = 0x7, /* no longer used */
    HTT_H2T_MSG_TYPE_WDI_IPA_CFG           = 0x8,
    HTT_H2T_MSG_TYPE_WDI_IPA_OP_REQ        = 0x9,
    HTT_H2T_MSG_TYPE_AGGR_CFG_EX           = 0xa, /* per vdev amsdu subfrm limit */
    HTT_H2T_MSG_TYPE_SRING_SETUP           = 0xb,
    HTT_H2T_MSG_TYPE_RX_RING_SELECTION_CFG = 0xc,
    HTT_H2T_MSG_TYPE_ADD_WDS_ENTRY         = 0xd,
    HTT_H2T_MSG_TYPE_DELETE_WDS_ENTRY      = 0xe,
    HTT_H2T_MSG_TYPE_RFS_CONFIG            = 0xf,
    HTT_H2T_MSG_TYPE_EXT_STATS_REQ         = 0x10,
    HTT_H2T_MSG_TYPE_PPDU_STATS_CFG        = 0x11,
    HTT_H2T_MSG_TYPE_RX_FSE_SETUP_CFG      = 0x12,
    HTT_H2T_MSG_TYPE_RX_FSE_OPERATION_CFG  = 0x13,
    HTT_H2T_MSG_TYPE_CHAN_CALDATA          = 0x14,
    HTT_H2T_MSG_TYPE_RX_FISA_CFG           = 0x15,
    HTT_H2T_MSG_TYPE_3_TUPLE_HASH_CFG      = 0x16,
    HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE  = 0x17,
    HTT_H2T_MSG_TYPE_HOST_PADDR_SIZE       = 0x18,
    HTT_H2T_MSG_TYPE_RXDMA_RXOLE_PPE_CFG   = 0x19,
    HTT_H2T_MSG_TYPE_VDEVS_TXRX_STATS_CFG  = 0x1a,

    /* keep this last */
    HTT_H2T_NUM_MSGS
};

/*
 * HTT host to target message type -
 * stored in bits 7:0 of the first word of the message
 */
#define HTT_H2T_MSG_TYPE_M      0xff
#define HTT_H2T_MSG_TYPE_S      0

#define HTT_H2T_MSG_TYPE_SET(word, msg_type)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_H2T_MSG_TYPE, msg_type); \
        (word) |= ((msg_type) << HTT_H2T_MSG_TYPE_S);  \
    } while (0)
#define HTT_H2T_MSG_TYPE_GET(word) \
    (((word) & HTT_H2T_MSG_TYPE_M) >> HTT_H2T_MSG_TYPE_S)

/**
 * @brief host -> target version number request message definition
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_VERSION_REQ
 *
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |                     reserved                     |    msg type    |
 *     |-------------------------------------------------------------------|
 *     :                    option request TLV (optional)                  |
 *     :...................................................................:
 *
 * The VER_REQ message may consist of a single 4-byte word, or may be
 * extended with TLVs that specify which HTT options the host is requesting
 * from the target.
 * The following option TLVs may be appended to the VER_REQ message:
 *   - HL_SUPPRESS_TX_COMPL_IND
 *   - HL_MAX_TX_QUEUE_GROUPS
 * These TLVs may appear in an arbitrary order.  Any number of these TLVs
 * may be appended to the VER_REQ message (but only one TLV of each type).
 *
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a version number request message
 *     Value: 0x0 (HTT_H2T_MSG_TYPE_VERSION_REQ)
 */

#define HTT_VER_REQ_BYTES 4

/* TBDXXX: figure out a reasonable number */
#define HTT_HL_DATA_SVC_PIPE_DEPTH         24
#define HTT_LL_DATA_SVC_PIPE_DEPTH         64

/**
 * @brief HTT tx MSDU descriptor
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_TX_FRM
 *
 * @details
 *  The HTT tx MSDU descriptor is created by the host HTT SW for each
 *  tx MSDU.  The HTT tx MSDU descriptor contains the information that
 *  the target firmware needs for the FW's tx processing, particularly
 *  for creating the HW msdu descriptor.
 *  The same HTT tx descriptor is used for HL and LL systems, though
 *  a few fields within the tx descriptor are used only by LL or
 *  only by HL.
 *  The HTT tx descriptor is defined in two manners: by a struct with
 *  bitfields, and by a series of [dword offset, bit mask, bit shift]
 *  definitions.
 *  The target should use the struct def, for simplicitly and clarity,
 *  but the host shall use the bit-mast + bit-shift defs, to be endian-
 *  neutral.  Specifically, the host shall use the get/set macros built
 *  around the mask + shift defs.
 */
#define HTT_TX_MSDU_DESC_RAW_SUBTYPE_80211_HDR_S   0
#define HTT_TX_MSDU_DESC_RAW_SUBTYPE_80211_HDR_M   0x1
#define HTT_TX_MSDU_DESC_RAW_SUBTYPE_NO_AGGR_S     1
#define HTT_TX_MSDU_DESC_RAW_SUBTYPE_NO_AGGR_M     0x2
#define HTT_TX_MSDU_DESC_RAW_SUBTYPE_NO_ENCRYPT_S  2
#define HTT_TX_MSDU_DESC_RAW_SUBTYPE_NO_ENCRYPT_M  0x4
#define HTT_TX_MSDU_DESC_RAW_SUBTYPE_NO_CLASSIFY_S 3
#define HTT_TX_MSDU_DESC_RAW_SUBTYPE_NO_CLASSIFY_M 0x8

#define HTT_TX_VDEV_ID_WORD 0
#define HTT_TX_VDEV_ID_MASK 0x3f
#define HTT_TX_VDEV_ID_SHIFT 16

#define HTT_TX_L3_CKSUM_OFFLOAD      1
#define HTT_TX_L4_CKSUM_OFFLOAD      2

#define HTT_TX_MSDU_LEN_DWORD 1
#define HTT_TX_MSDU_LEN_MASK 0xffff;

/*
 * HTT_VAR_PADDR macros
 * Allow physical / bus addresses to be either a single 32-bit value,
 * or a 64-bit value, stored as a little-endian lo,hi pair of 32-bit parts
 */
#define HTT_VAR_PADDR32(var_name) \
    A_UINT32 var_name
#define HTT_VAR_PADDR64_LE(var_name)        \
    struct {                                \
        /* little-endian: lo precedes hi */ \
        A_UINT32 lo;                        \
        A_UINT32 hi;                        \
    } var_name

/*
 * TEMPLATE_HTT_TX_MSDU_DESC_T:
 * This macro defines a htt_tx_msdu_descXXX_t in which any physical
 * addresses are stored in a XXX-bit field.
 * This macro is used to define both htt_tx_msdu_desc32_t and
 * htt_tx_msdu_desc64_t structs.
 */
#define TEMPLATE_HTT_TX_MSDU_DESC_T(_paddr_bits_, _paddr__frags_desc_ptr_)     \
PREPACK struct htt_tx_msdu_desc ## _paddr_bits_ ## _t                          \
{                                                                              \
    /* DWORD 0: flags and meta-data */                                         \
    A_UINT32                                                                   \
        msg_type: 8, /* HTT_H2T_MSG_TYPE_TX_FRM */                             \
                                                                               \
        /* pkt_subtype -                                                       \
         * Detailed specification of the tx frame contents, extending the      \
         * general specification provided by pkt_type.                         \
         * FIX THIS: ADD COMPLETE SPECS FOR THIS FIELDS VALUE, e.g.            \
         *     pkt_type    | pkt_subtype                                       \
         *     ==============================================================  \
         *     802.3       | bit 0:3    - Reserved                             \
         *                 | bit 4: 0x0 - Copy-Engine Classification Results   \
         *                 |              not appended to the HTT message      \
         *                 |        0x1 - Copy-Engine Classification Results   \
         *                 |              appended to the HTT message in the   \
         *                 |              format:                              \
         *                 |              [HTT tx desc, frame header,          \
         *                 |              CE classification results]           \
         *                 |              The CE classification results begin  \
         *                 |              at the next 4-byte boundary after    \
         *                 |              the frame header.                    \
         *     ------------+-------------------------------------------------  \
         *     Eth2        | bit 0:3    - Reserved                             \
         *                 | bit 4: 0x0 - Copy-Engine Classification Results   \
         *                 |              not appended to the HTT message      \
         *                 |        0x1 - Copy-Engine Classification Results   \
         *                 |              appended to the HTT message.         \
         *                 |              See the above specification of the   \
         *                 |              CE classification results location.  \
         *     ------------+-------------------------------------------------  \
         *     native WiFi | bit 0:3    - Reserved                             \
         *                 | bit 4: 0x0 - Copy-Engine Classification Results   \
         *                 |              not appended to the HTT message      \
         *                 |        0x1 - Copy-Engine Classification Results   \
         *                 |              appended to the HTT message.         \
         *                 |              See the above specification of the   \
         *                 |              CE classification results location.  \
         *     ------------+-------------------------------------------------  \
         *     mgmt        | 0x0 - 802.11 MAC header absent                    \
         *                 | 0x1 - 802.11 MAC header present                   \
         *     ------------+-------------------------------------------------  \
         *     raw         | bit 0: 0x0 - 802.11 MAC header absent             \
         *                 |        0x1 - 802.11 MAC header present            \
         *                 | bit 1: 0x0 - allow aggregation                    \
         *                 |        0x1 - don't allow aggregation              \
         *                 | bit 2: 0x0 - perform encryption                   \
         *                 |        0x1 - don't perform encryption             \
         *                 | bit 3: 0x0 - perform tx classification / queuing  \
         *                 |        0x1 - don't perform tx classification;     \
         *                 |              insert the frame into the "misc"     \
         *                 |              tx queue                             \
         *                 | bit 4: 0x0 - Copy-Engine Classification Results   \
         *                 |              not appended to the HTT message      \
         *                 |        0x1 - Copy-Engine Classification Results   \
         *                 |              appended to the HTT message.         \
         *                 |              See the above specification of the   \
         *                 |              CE classification results location.  \
         */                                                                    \
        pkt_subtype: 5,                                                        \
                                                                               \
        /* pkt_type -                                                          \
         * General specification of the tx frame contents.                     \
         * The htt_pkt_type enum should be used to specify and check the       \
         * value of this field.                                                \
         */                                                                    \
        pkt_type: 3,                                                           \
                                                                               \
        /* vdev_id -                                                           \
         * ID for the vdev that is sending this tx frame.                      \
         * For certain non-standard packet types, e.g. pkt_type == raw         \
         * and (pkt_subtype >> 3) == 1, this field is not relevant/valid.      \
         * This field is used primarily for determining where to queue         \
         * broadcast and multicast frames.                                     \
         */                                                                    \
        vdev_id: 6,                                                            \
        /* ext_tid -                                                           \
         * The extended traffic ID.                                            \
         * If the TID is unknown, the extended TID is set to                   \
         * HTT_TX_EXT_TID_INVALID.                                             \
         * If the tx frame is QoS data, then the extended TID has the 0-15     \
         * value of the QoS TID.                                               \
         * If the tx frame is non-QoS data, then the extended TID is set to    \
         * HTT_TX_EXT_TID_NON_QOS.                                             \
         * If the tx frame is multicast or broadcast, then the extended TID    \
         * is set to HTT_TX_EXT_TID_MCAST_BCAST.                               \
         */                                                                    \
        ext_tid: 5,                                                            \
                                                                               \
        /* postponed -                                                         \
         * This flag indicates whether the tx frame has been downloaded to     \
         * the target before but discarded by the target, and now is being     \
         * downloaded again; or if this is a new frame that is being           \
         * downloaded for the first time.                                      \
         * This flag allows the target to determine the correct order for      \
         * transmitting new vs. old frames.                                    \
         * value: 0 -> new frame, 1 -> re-send of a previously sent frame      \
         * This flag only applies to HL systems, since in LL systems,          \
         * the tx flow control is handled entirely within the target.          \
         */                                                                    \
        postponed: 1,                                                          \
                                                                               \
        /* extension -                                                         \
         * This flag indicates whether a HTT tx MSDU extension descriptor      \
         * (htt_tx_msdu_desc_ext_t) follows this HTT tx MSDU descriptor.       \
         *                                                                     \
         * 0x0 - no extension MSDU descriptor is present                       \
         * 0x1 - an extension MSDU descriptor immediately follows the          \
         *       regular MSDU descriptor                                       \
         */                                                                    \
        extension: 1,                                                          \
                                                                               \
        /* cksum_offload -                                                     \
         * This flag indicates whether checksum offload is enabled or not      \
         * for this frame. Target FW use this flag to turn on HW checksumming  \
         *  0x0 - No checksum offload                                          \
         *  0x1 - L3 header checksum only                                      \
         *  0x2 - L4 checksum only                                             \
         *  0x3 - L3 header checksum + L4 checksum                             \
         */                                                                    \
        cksum_offload: 2,                                                      \
                                                                               \
        /* tx_comp_req -                                                       \
         * This flag indicates whether Tx Completion                           \
         * from fw is required or not.                                         \
         * This  flag is only relevant if tx completion is not                 \
         * universally enabled.                                                \
         * For all LL systems, tx completion is mandatory,                     \
         * so this flag will be irrelevant.                                    \
         * For HL systems tx completion is optional, but HL systems in which   \
         * the bus throughput exceeds the WLAN throughput will                 \
         * probably want to always use tx completion, and thus                 \
         * would not check this flag.                                          \
         * This flag is required when tx completions are not used universally, \
         * but are still required for certain tx frames for which              \
         * an OTA delivery acknowledgment is needed by the host.               \
         * In practice, this would be for HL systems in which the              \
         * bus throughput is less than the WLAN throughput.                    \
         *                                                                     \
         * 0x0 - Tx Completion Indication from Fw not required                 \
         * 0x1 - Tx Completion Indication from Fw is required                  \
         */                                                                    \
        tx_compl_req: 1;                                                       \
                                                                               \
                                                                               \
        /* DWORD 1: MSDU length and ID */                                      \
        A_UINT32                                                               \
            len: 16, /* MSDU length, in bytes */                               \
            id:  16; /* MSDU ID used to identify the MSDU to the host,         \
                      * and this id is used to calculate fragmentation         \
                      * descriptor pointer inside the target based on          \
                      * the base address, configured inside the target.        \
                      */                                                       \
                                                                               \
        /* DWORD 2 (or 2-3): fragmentation descriptor bus address */           \
        /* frags_desc_ptr -                                                    \
         * The fragmentation descriptor pointer tells the HW's MAC DMA         \
         * where the tx frame's fragments reside in memory.                    \
         * This field only applies to LL systems, since in HL systems the      \
         * (degenerate single-fragment) fragmentation descriptor is created    \
         * within the target.                                                  \
         */                                                                    \
        _paddr__frags_desc_ptr_;                                               \
                                                                               \
        /* DWORD 3 (or 4): peerid, chanfreq */                                 \
        /*                                                                     \
         * Peer ID : Target can use this value to know which peer-id packet    \
         *           destined to.                                              \
         *           It's intended to be specified by host in case of NAWDS.   \
         */                                                                    \
        A_UINT16 peerid;                                                       \
                                                                               \
        /*                                                                     \
         * Channel frequency: This identifies the desired channel              \
         * frequency (in mhz) for tx frames. This is used by FW to help        \
         * determine when it is safe to transmit or drop frames for            \
         * off-channel operation.                                              \
         * The default value of zero indicates to FW that the corresponding    \
         * VDEV's home channel (if there is one) is the desired channel        \
         * frequency.                                                          \
         */                                                                    \
        A_UINT16 chanfreq;                                                     \
                                                                               \
        /* Reason reserved is commented is increasing the htt structure size   \
         * leads to some wierd issues. Contact Raj/Kyeyoon for more info       \
         * A_UINT32 reserved_dword3_bits0_31;                                  \
         */                                                                    \
} POSTPACK
/* define a htt_tx_msdu_desc32_t type */
TEMPLATE_HTT_TX_MSDU_DESC_T(32, HTT_VAR_PADDR32(frags_desc_ptr));
/* define a htt_tx_msdu_desc64_t type */
TEMPLATE_HTT_TX_MSDU_DESC_T(64, HTT_VAR_PADDR64_LE(frags_desc_ptr));
/*
 * Make htt_tx_msdu_desc_t be an alias for either
 * htt_tx_msdu_desc32_t or htt_tx_msdu_desc64_t
 */
#if HTT_PADDR64
    #define htt_tx_msdu_desc_t htt_tx_msdu_desc64_t
#else
    #define htt_tx_msdu_desc_t htt_tx_msdu_desc32_t
#endif

/* decriptor information for Management frame*/
/*
 * THIS htt_mgmt_tx_desc_t STRUCT IS DEPRECATED - DON'T USE IT.
 * BOTH MANAGEMENT AND DATA FRAMES SHOULD USE htt_tx_msdu_desc_t.
 */
#define HTT_MGMT_FRM_HDR_DOWNLOAD_LEN    32
extern A_UINT32 mgmt_hdr_len;
PREPACK struct htt_mgmt_tx_desc_t {
    A_UINT32    msg_type;
#if HTT_PADDR64
    A_UINT64    frag_paddr; /* DMAble address of the data */
#else
    A_UINT32    frag_paddr; /* DMAble address of the data */
#endif
    A_UINT32    desc_id;    /* returned to host during completion
                             * to free the meory*/
    A_UINT32    len;    /* Fragment length */
    A_UINT32    vdev_id; /* virtual device ID*/
    A_UINT8     hdr[HTT_MGMT_FRM_HDR_DOWNLOAD_LEN]; /* frm header */
} POSTPACK;

PREPACK struct htt_mgmt_tx_compl_ind {
    A_UINT32    desc_id;
    A_UINT32    status;
} POSTPACK;

/*
 * This SDU header size comes from the summation of the following:
 *  1. Max of:
 *     a.  Native WiFi header, for native WiFi frames: 24 bytes
 *         (frame control, duration / ID, addr1, addr2, addr3, seq ctrl, addr4)
 *     b.  802.11 header, for raw frames: 36 bytes
 *         (frame control, duration / ID, addr1, addr2, addr3, seq ctrl, addr4,
 *         QoS header, HT header)
 *     c.  802.3 header, for ethernet frames: 14 bytes
 *         (destination address, source address, ethertype / length)
 *  2. Max of:
 *     a.  IPv4 header, up through the DiffServ Code Point: 2 bytes
 *     b.  IPv6 header, up through the Traffic Class: 2 bytes
 *  3. 802.1Q VLAN header: 4 bytes
 *  4. LLC/SNAP header: 8 bytes
 */
#define HTT_TX_HDR_SIZE_NATIVE_WIFI 30
#define HTT_TX_HDR_SIZE_802_11_RAW 36
#define HTT_TX_HDR_SIZE_ETHERNET 14

#define HTT_TX_HDR_SIZE_OUTER_HDR_MAX HTT_TX_HDR_SIZE_802_11_RAW
A_COMPILE_TIME_ASSERT(
    htt_encap_hdr_size_max_check_nwifi,
    HTT_TX_HDR_SIZE_OUTER_HDR_MAX >= HTT_TX_HDR_SIZE_NATIVE_WIFI);
A_COMPILE_TIME_ASSERT(
    htt_encap_hdr_size_max_check_enet,
    HTT_TX_HDR_SIZE_OUTER_HDR_MAX >= HTT_TX_HDR_SIZE_ETHERNET);

#define HTT_HL_TX_HDR_SIZE_IP 1600    /* also include payload */
#define HTT_LL_TX_HDR_SIZE_IP 16      /* up to the end of UDP header for IPv4 case */

#define HTT_TX_HDR_SIZE_802_1Q 4
#define HTT_TX_HDR_SIZE_LLC_SNAP 8


#define HTT_COMMON_TX_FRM_HDR_LEN \
     (HTT_TX_HDR_SIZE_OUTER_HDR_MAX + \
     HTT_TX_HDR_SIZE_802_1Q + \
     HTT_TX_HDR_SIZE_LLC_SNAP)

#define HTT_HL_TX_FRM_HDR_LEN \
     (HTT_COMMON_TX_FRM_HDR_LEN + HTT_HL_TX_HDR_SIZE_IP)

#define HTT_LL_TX_FRM_HDR_LEN \
     (HTT_COMMON_TX_FRM_HDR_LEN + HTT_LL_TX_HDR_SIZE_IP)

#define HTT_TX_DESC_LEN  sizeof(struct htt_tx_msdu_desc_t)

/* dword 0 */
#define HTT_TX_DESC_PKT_SUBTYPE_OFFSET_BYTES 0
#define HTT_TX_DESC_PKT_SUBTYPE_OFFSET_DWORD 0
#define HTT_TX_DESC_PKT_SUBTYPE_M      0x00001f00
#define HTT_TX_DESC_PKT_SUBTYPE_S      8

#define HTT_TX_DESC_NO_ENCRYPT_OFFSET_BYTES 0
#define HTT_TX_DESC_NO_ENCRYPT_OFFSET_DWORD 0
#define HTT_TX_DESC_NO_ENCRYPT_M      0x00000400
#define HTT_TX_DESC_NO_ENCRYPT_S      10

#define HTT_TX_DESC_PKT_TYPE_OFFSET_BYTES 0
#define HTT_TX_DESC_PKT_TYPE_OFFSET_DWORD 0
#define HTT_TX_DESC_PKT_TYPE_M         0x0000e000
#define HTT_TX_DESC_PKT_TYPE_S         13

#define HTT_TX_DESC_VDEV_ID_OFFSET_BYTES 0
#define HTT_TX_DESC_VDEV_ID_OFFSET_DWORD 0
#define HTT_TX_DESC_VDEV_ID_M          0x003f0000
#define HTT_TX_DESC_VDEV_ID_S          16

#define HTT_TX_DESC_EXT_TID_OFFSET_BYTES 0
#define HTT_TX_DESC_EXT_TID_OFFSET_DWORD 0
#define HTT_TX_DESC_EXT_TID_M          0x07c00000
#define HTT_TX_DESC_EXT_TID_S          22

#define HTT_TX_DESC_POSTPONED_OFFSET_BYTES 0
#define HTT_TX_DESC_POSTPONED_OFFSET_DWORD 0
#define HTT_TX_DESC_POSTPONED_M        0x08000000
#define HTT_TX_DESC_POSTPONED_S        27

#define HTT_TX_DESC_EXTENSION_OFFSET_BYTE 0
#define HTT_TX_DESC_EXTENSION_OFFSET_DWORD 0
#define HTT_TX_DESC_EXTENSION_M        0x10000000
#define HTT_TX_DESC_EXTENSION_S        28

#define HTT_TX_DESC_CKSUM_OFFLOAD_OFFSET_BYTES 0
#define HTT_TX_DESC_CKSUM_OFFLOAD_OFFSET_DWORD 0
#define HTT_TX_DESC_CKSUM_OFFLOAD_M 0x60000000
#define HTT_TX_DESC_CKSUM_OFFLOAD_S 29

#define HTT_TX_DESC_TX_COMP_OFFSET_BYTES 0
#define HTT_TX_DESC_TX_COMP_OFFSET_DWORD 0
#define HTT_TX_DESC_TX_COMP_M 0x80000000
#define HTT_TX_DESC_TX_COMP_S 31

/* dword 1 */
#define HTT_TX_DESC_FRM_LEN_OFFSET_BYTES 4
#define HTT_TX_DESC_FRM_LEN_OFFSET_DWORD 1
#define HTT_TX_DESC_FRM_LEN_M          0x0000ffff
#define HTT_TX_DESC_FRM_LEN_S          0

#define HTT_TX_DESC_FRM_ID_OFFSET_BYTES 4
#define HTT_TX_DESC_FRM_ID_OFFSET_DWORD 1
#define HTT_TX_DESC_FRM_ID_M           0xffff0000
#define HTT_TX_DESC_FRM_ID_S           16

/* dword 2 */
#define HTT_TX_DESC_FRAGS_DESC_PADDR_OFFSET_BYTES 8
#define HTT_TX_DESC_FRAGS_DESC_PADDR_OFFSET_DWORD 2
/* for systems using 64-bit format for bus addresses */
#define HTT_TX_DESC_FRAGS_DESC_PADDR_HI_M 0xffffffff
#define HTT_TX_DESC_FRAGS_DESC_PADDR_HI_S 0
#define HTT_TX_DESC_FRAGS_DESC_PADDR_LO_M 0xffffffff
#define HTT_TX_DESC_FRAGS_DESC_PADDR_LO_S 0
/* for systems using 32-bit format for bus addresses */
#define HTT_TX_DESC_FRAGS_DESC_PADDR_M    0xffffffff
#define HTT_TX_DESC_FRAGS_DESC_PADDR_S    0

/* dword 3 */
#define HTT_TX_DESC_PEER_ID_OFFSET_BYTES_64 16
#define HTT_TX_DESC_PEER_ID_OFFSET_BYTES_32 12
#define HTT_TX_DESC_PEER_ID_OFFSET_DWORD_64 \
        (HTT_TX_DESC_PEER_ID_OFFSET_BYTES_64 >> 2)
#define HTT_TX_DESC_PEER_ID_OFFSET_DWORD_32 \
        (HTT_TX_DESC_PEER_ID_OFFSET_BYTES_32 >> 2)

#if HTT_PADDR64
#define HTT_TX_DESC_PEER_ID_OFFSET_BYTES HTT_TX_DESC_PEER_ID_OFFSET_BYTES_64
#define HTT_TX_DESC_PEER_ID_OFFSET_DWORD HTT_TX_DESC_PEER_ID_OFFSET_DWORD_64
#else
#define HTT_TX_DESC_PEER_ID_OFFSET_BYTES HTT_TX_DESC_PEER_ID_OFFSET_BYTES_32
#define HTT_TX_DESC_PEER_ID_OFFSET_DWORD HTT_TX_DESC_PEER_ID_OFFSET_DWORD_32
#endif

#define HTT_TX_DESC_PEER_ID_M 0x0000ffff
#define HTT_TX_DESC_PEER_ID_S 0
    /*
     * TEMPORARY:
     * The original definitions for the PEER_ID fields contained typos
     * (with _DESC_PADDR appended to this PEER_ID field name).
     * Retain deprecated original names for PEER_ID fields until all code that
     * refers to them has been updated.
     */
    #define HTT_TX_DESC_PEERID_DESC_PADDR_OFFSET_BYTES \
        HTT_TX_DESC_PEER_ID_OFFSET_BYTES
    #define HTT_TX_DESC_PEERID_DESC_PADDR_OFFSET_DWORD \
        HTT_TX_DESC_PEER_ID_OFFSET_DWORD
    #define HTT_TX_DESC_PEERID_DESC_PADDR_M \
        HTT_TX_DESC_PEER_ID_M
    #define HTT_TX_DESC_PEERID_DESC_PADDR_S \
        HTT_TX_DESC_PEER_ID_S

#define HTT_TX_DESC_CHAN_FREQ_OFFSET_BYTES_64 16 /* to dword with chan freq */
#define HTT_TX_DESC_CHAN_FREQ_OFFSET_BYTES_32 12 /* to dword with chan freq */
#define HTT_TX_DESC_CHAN_FREQ_OFFSET_DWORD_64 \
        (HTT_TX_DESC_CHAN_FREQ_OFFSET_BYTES_64 >> 2)
#define HTT_TX_DESC_CHAN_FREQ_OFFSET_DWORD_32 \
        (HTT_TX_DESC_CHAN_FREQ_OFFSET_BYTES_32 >> 2)

#if HTT_PADDR64
#define HTT_TX_DESC_CHAN_FREQ_OFFSET_BYTES HTT_TX_DESC_CHAN_FREQ_OFFSET_BYTES_64
#define HTT_TX_DESC_CHAN_FREQ_OFFSET_DWORD HTT_TX_DESC_CHAN_FREQ_OFFSET_DWORD_64
#else
#define HTT_TX_DESC_CHAN_FREQ_OFFSET_BYTES HTT_TX_DESC_CHAN_FREQ_OFFSET_BYTES_32
#define HTT_TX_DESC_CHAN_FREQ_OFFSET_DWORD HTT_TX_DESC_CHAN_FREQ_OFFSET_DWORD_32
#endif

#define HTT_TX_DESC_CHAN_FREQ_M 0xffff0000
#define HTT_TX_DESC_CHAN_FREQ_S 16

#define HTT_TX_DESC_PKT_SUBTYPE_GET(_var) \
    (((_var) & HTT_TX_DESC_PKT_SUBTYPE_M) >> HTT_TX_DESC_PKT_SUBTYPE_S)
#define HTT_TX_DESC_PKT_SUBTYPE_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_PKT_SUBTYPE, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_PKT_SUBTYPE_S)); \
    } while (0)

#define HTT_TX_DESC_NO_ENCRYPT_GET(_var) \
    (((_var) & HTT_TX_DESC_NO_ENCRYPT_M) >> HTT_TX_DESC_NO_ENCRYPT_S)
#define HTT_TX_DESC_NO_ENCRYPT_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_NO_ENCRYPT, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_NO_ENCRYPT_S)); \
    } while (0)

#define HTT_TX_DESC_PKT_TYPE_GET(_var) \
    (((_var) & HTT_TX_DESC_PKT_TYPE_M) >> HTT_TX_DESC_PKT_TYPE_S)
#define HTT_TX_DESC_PKT_TYPE_SET(_var, _val)            \
    do {                                                \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_PKT_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_PKT_TYPE_S)); \
    } while (0)

#define HTT_TX_DESC_VDEV_ID_GET(_var) \
    (((_var) & HTT_TX_DESC_VDEV_ID_M) >> HTT_TX_DESC_VDEV_ID_S)
#define HTT_TX_DESC_VDEV_ID_SET(_var, _val)            \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_VDEV_ID, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_VDEV_ID_S)); \
    } while (0)

#define HTT_TX_DESC_EXT_TID_GET(_var) \
    (((_var) & HTT_TX_DESC_EXT_TID_M) >> HTT_TX_DESC_EXT_TID_S)
#define HTT_TX_DESC_EXT_TID_SET(_var, _val)            \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_EXT_TID, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_EXT_TID_S)); \
    } while (0)

#define HTT_TX_DESC_POSTPONED_GET(_var) \
    (((_var) & HTT_TX_DESC_POSTPONED_M) >> HTT_TX_DESC_POSTPONED_S)
#define HTT_TX_DESC_POSTPONED_SET(_var, _val)            \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_POSTPONED, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_POSTPONED_S)); \
    } while (0)

#define HTT_TX_DESC_EXTENSION_GET(_var) \
    (((_var) & HTT_TX_DESC_EXTENSION_M) >> HTT_TX_DESC_EXTENSION_S)
#define HTT_TX_DESC_EXTENSION_SET(_var, _val)            \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_EXTENSION, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_EXTENSION_S)); \
    } while (0)

#define HTT_TX_DESC_FRM_LEN_GET(_var) \
    (((_var) & HTT_TX_DESC_FRM_LEN_M) >> HTT_TX_DESC_FRM_LEN_S)
#define HTT_TX_DESC_FRM_LEN_SET(_var, _val)            \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_FRM_LEN, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_FRM_LEN_S)); \
    } while (0)

#define HTT_TX_DESC_FRM_ID_GET(_var) \
    (((_var) & HTT_TX_DESC_FRM_ID_M) >> HTT_TX_DESC_FRM_ID_S)
#define HTT_TX_DESC_FRM_ID_SET(_var, _val)            \
    do {                                              \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_FRM_ID, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_FRM_ID_S)); \
    } while (0)

#define HTT_TX_DESC_CKSUM_OFFLOAD_GET(_var) \
    (((_var) & HTT_TX_DESC_CKSUM_OFFLOAD_M) >> HTT_TX_DESC_CKSUM_OFFLOAD_S)
#define HTT_TX_DESC_CKSUM_OFFLOAD_SET(_var, _val)            \
    do {                                              \
        HTT_CHECK_SET_VAL(HTT_TX_DESC_CKSUM_OFFLOAD, _val);  \
        ((_var) |= ((_val) << HTT_TX_DESC_CKSUM_OFFLOAD_S)); \
    } while (0)

#define HTT_TX_DESC_TX_COMP_GET(_var) \
    (((_var) & HTT_TX_DESC_TX_COMP_M) >> HTT_TX_DESC_TX_COMP_S)
#define HTT_TX_DESC_TX_COMP_SET(_var, _val)             \
     do {                                               \
         HTT_CHECK_SET_VAL(HTT_TX_DESC_TX_COMP, _val);  \
         ((_var) |= ((_val) << HTT_TX_DESC_TX_COMP_S)); \
     } while (0)

#define HTT_TX_DESC_PEER_ID_GET(_var) \
    (((_var) & HTT_TX_DESC_PEER_ID_M) >> HTT_TX_DESC_PEER_ID_S)
#define HTT_TX_DESC_PEER_ID_SET(_var, _val)             \
     do {                                               \
         HTT_CHECK_SET_VAL(HTT_TX_DESC_PEER_ID, _val);  \
         ((_var) |= ((_val) << HTT_TX_DESC_PEER_ID_S)); \
     } while (0)

#define HTT_TX_DESC_CHAN_FREQ_GET(_var) \
    (((_var) & HTT_TX_DESC_CHAN_FREQ_M) >> HTT_TX_DESC_CHAN_FREQ_S)
#define HTT_TX_DESC_CHAN_FREQ_SET(_var, _val)             \
     do {                                               \
         HTT_CHECK_SET_VAL(HTT_TX_DESC_CHAN_FREQ, _val);  \
         ((_var) |= ((_val) << HTT_TX_DESC_CHAN_FREQ_S)); \
     } while (0)


/* enums used in the HTT tx MSDU extension descriptor */
enum {
    htt_tx_guard_interval_regular = 0,
    htt_tx_guard_interval_short   = 1,
};

enum {
    htt_tx_preamble_type_ofdm = 0,
    htt_tx_preamble_type_cck  = 1,
    htt_tx_preamble_type_ht   = 2,
    htt_tx_preamble_type_vht  = 3,
};

enum {
    htt_tx_bandwidth_5MHz   = 0,
    htt_tx_bandwidth_10MHz  = 1,
    htt_tx_bandwidth_20MHz  = 2,
    htt_tx_bandwidth_40MHz  = 3,
    htt_tx_bandwidth_80MHz  = 4,
    htt_tx_bandwidth_160MHz = 5, /* includes 80+80 */
};

/**
 * @brief HTT tx MSDU extension descriptor
 * @details
 *  If the target supports HTT tx MSDU extension descriptors, the host has
 *  the option of appending the following struct following the regular
 *  HTT tx MSDU descriptor (and setting the "extension" flag in the regular
 *  HTT tx MSDU descriptor, to show that the extension descriptor is present).
 *  The HTT tx MSDU extension descriptors allows the host to provide detailed
 *  tx specs for each frame.
 */
PREPACK struct htt_tx_msdu_desc_ext_t {
    /* DWORD 0: flags */
    A_UINT32
        valid_pwr:            1, /* bit 0: if set, tx pwr spec is valid */
        valid_mcs_mask:       1, /* bit 1: if set, tx MCS mask spec is valid */
        valid_nss_mask:       1, /* bit 2: if set, tx Nss mask spec is valid */
        valid_guard_interval: 1, /* bit 3: if set, tx guard intv spec is valid*/
        valid_preamble_type_mask: 1, /* 4: if set, tx preamble mask is valid */
        valid_chainmask:      1, /* bit 5: if set, tx chainmask spec is valid */
        valid_retries:        1, /* bit 6: if set, tx retries spec is valid */
        valid_bandwidth:      1, /* bit 7: if set, tx bandwidth spec is valid */
        valid_expire_tsf:     1, /* bit 8: if set, tx expire TSF spec is valid*/
        is_dsrc:              1, /* bit 9: if set, MSDU is a DSRC frame */
        reserved0_31_7:      22; /* bits 31:10 - unused, set to 0x0 */

    /* DWORD 1: tx power, tx rate, tx BW */
    A_UINT32
        /* pwr -
         * Specify what power the tx frame needs to be transmitted at.
         * The power a signed (two's complement) value is in units of 0.5 dBm.
         * The value needs to be appropriately sign-extended when extracting
         * the value from the message and storing it in a variable that is
         * larger than A_INT8.  (The HTT_TX_MSDU_EXT_DESC_FLAG_PWR_GET macro
         * automatically handles this sign-extension.)
         * If the transmission uses multiple tx chains, this power spec is
         * the total transmit power, assuming incoherent combination of
         * per-chain power to produce the total power.
         */
        pwr: 8,

        /* mcs_mask -
         * Specify the allowable values for MCS index (modulation and coding)
         * to use for transmitting the frame.
         *
         * For HT / VHT preamble types, this mask directly corresponds to
         * the HT or VHT MCS indices that are allowed.  For each bit N set
         * within the mask, MCS index N is allowed for transmitting the frame.
         * For legacy CCK and OFDM rates, separate bits are provided for CCK
         * rates versus OFDM rates, so the host has the option of specifying
         * that the target must transmit the frame with CCK or OFDM rates
         * (not HT or VHT), but leaving the decision to the target whether
         * to use CCK or OFDM.
         *
         * For CCK and OFDM, the bits within this mask are interpreted as
         * follows:
         *     bit  0 -> CCK 1 Mbps rate is allowed
         *     bit  1 -> CCK 2 Mbps rate is allowed
         *     bit  2 -> CCK 5.5 Mbps rate is allowed
         *     bit  3 -> CCK 11 Mbps rate is allowed
         *     bit  4 -> OFDM BPSK modulation, 1/2 coding rate is allowed
         *     bit  5 -> OFDM BPSK modulation, 3/4 coding rate is allowed
         *     bit  6 -> OFDM QPSK modulation, 1/2 coding rate is allowed
         *     bit  7 -> OFDM QPSK modulation, 3/4 coding rate is allowed
         *     bit  8 -> OFDM 16-QAM modulation, 1/2 coding rate is allowed
         *     bit  9 -> OFDM 16-QAM modulation, 3/4 coding rate is allowed
         *     bit 10 -> OFDM 64-QAM modulation, 2/3 coding rate is allowed
         *     bit 11 -> OFDM 64-QAM modulation, 3/4 coding rate is allowed
         *
         * The MCS index specification needs to be compatible with the
         * bandwidth mask specification.  For example, a MCS index == 9
         * specification is inconsistent with a preamble type == VHT,
         * Nss == 1, and channel bandwidth == 20 MHz.
         *
         * Furthermore, the host has only a limited ability to specify to
         * the target to select from HT + legacy rates, or VHT + legacy rates,
         * since this mcs_mask can specify either HT/VHT rates or legacy rates.
         */
        mcs_mask: 12,

        /* nss_mask -
         * Specify which numbers of spatial streams (MIMO factor) are permitted.
         * Each bit in this mask corresponds to a Nss value:
         *     bit 0: if set, Nss = 1 (non-MIMO) is permitted
         *     bit 1: if set, Nss = 2 (2x2 MIMO) is permitted
         *     bit 2: if set, Nss = 3 (3x3 MIMO) is permitted
         *     bit 3: if set, Nss = 4 (4x4 MIMO) is permitted
         * The values in the Nss mask must be suitable for the recipient, e.g.
         * a value of 0x4 (Nss = 3) cannot be specified for a tx frame to a
         * recipient which only supports 2x2 MIMO.
         */
        nss_mask: 4,

        /* guard_interval -
         * Specify a htt_tx_guard_interval enum value to indicate whether
         * the transmission should use a regular guard interval or a
         * short guard interval.
         */
        guard_interval: 1,

        /* preamble_type_mask -
         * Specify which preamble types (CCK, OFDM, HT, VHT) the target
         * may choose from for transmitting this frame.
         * The bits in this mask correspond to the values in the
         * htt_tx_preamble_type enum.  For example, to allow the target
         * to transmit the frame as either CCK or OFDM, this field would
         * be set to
         *     (1 << htt_tx_preamble_type_ofdm) |
         *     (1 << htt_tx_preamble_type_cck)
         */
        preamble_type_mask: 4,

        reserved1_31_29: 3; /* unused, set to 0x0 */

    /* DWORD 2: tx chain mask, tx retries */
    A_UINT32
        /* chain_mask - specify which chains to transmit from */
        chain_mask: 4,

        /* retry_limit -
         * Specify the maximum number of transmissions, including the
         * initial transmission, to attempt before giving up if no ack
         * is received.
         * If the tx rate is specified, then all retries shall use the
         * same rate as the initial transmission.
         * If no tx rate is specified, the target can choose whether to
         * retain the original rate during the retransmissions, or to
         * fall back to a more robust rate.
         */
        retry_limit: 4,

        /* bandwidth_mask -
         * Specify what channel widths may be used for the transmission.
         * A value of zero indicates "don't care" - the target may choose
         * the transmission bandwidth.
         * The bits within this mask correspond to the htt_tx_bandwidth
         * enum values - bit 0 is for 5 MHz, bit 1 is for 10 MHz, etc.
         * The bandwidth_mask must be consistent with the preamble_type_mask
         * and mcs_mask specs, if they are provided.  For example, 80 MHz and
         * 160 MHz can only be enabled in the mask if preamble_type == VHT.
         */
        bandwidth_mask: 6,

        reserved2_31_14: 18; /* unused, set to 0x0 */

    /* DWORD 3: tx expiry time (TSF) LSBs */
    A_UINT32 expire_tsf_lo;

    /* DWORD 4: tx expiry time (TSF) MSBs */
    A_UINT32 expire_tsf_hi;

    A_UINT32 reserved_for_future_expansion_set_to_zero[3];
} POSTPACK;

/* DWORD 0 */
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR_M                0x00000001
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR_S                0
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_MCS_MASK_M           0x00000002
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_MCS_MASK_S           1
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_NSS_MASK_M           0x00000004
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_NSS_MASK_S           2
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_GUARD_INTERVAL_M     0x00000008
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_GUARD_INTERVAL_S     3
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PREAMBLE_TYPE_MASK_M 0x00000010
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PREAMBLE_TYPE_MASK_S 4
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_CHAIN_MASK_M         0x00000020
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_CHAIN_MASK_S         5
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_RETRIES_M            0x00000040
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_RETRIES_S            6
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_BANDWIDTH_M          0x00000080
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_BANDWIDTH_S          7
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_EXPIRE_TIME_M        0x00000100
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_EXPIRE_TIME_S        8
#define HTT_TX_MSDU_EXT_DESC_FLAG_IS_DSRC_M                  0x00000200
#define HTT_TX_MSDU_EXT_DESC_FLAG_IS_DSRC_S                  9

/* DWORD 1 */
#define HTT_TX_MSDU_EXT_DESC_PWR_M                           0x000000ff
#define HTT_TX_MSDU_EXT_DESC_PWR_S                           0
#define HTT_TX_MSDU_EXT_DESC_MCS_MASK_M                      0x000fff00
#define HTT_TX_MSDU_EXT_DESC_MCS_MASK_S                      8
#define HTT_TX_MSDU_EXT_DESC_NSS_MASK_M                      0x00f00000
#define HTT_TX_MSDU_EXT_DESC_NSS_MASK_S                      20
#define HTT_TX_MSDU_EXT_DESC_GUARD_INTERVAL_M                0x01000000
#define HTT_TX_MSDU_EXT_DESC_GUARD_INTERVAL_S                24
#define HTT_TX_MSDU_EXT_DESC_PREAMBLE_TYPE_MASK_M            0x1c000000
#define HTT_TX_MSDU_EXT_DESC_PREAMBLE_TYPE_MASK_S            25

/* DWORD 2 */
#define HTT_TX_MSDU_EXT_DESC_CHAIN_MASK_M                    0x0000000f
#define HTT_TX_MSDU_EXT_DESC_CHAIN_MASK_S                    0
#define HTT_TX_MSDU_EXT_DESC_RETRY_LIMIT_M                   0x000000f0
#define HTT_TX_MSDU_EXT_DESC_RETRY_LIMIT_S                   4
#define HTT_TX_MSDU_EXT_DESC_BANDWIDTH_MASK_M                0x00003f00
#define HTT_TX_MSDU_EXT_DESC_BANDWIDTH_MASK_S                8


/* DWORD 0 */
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_MCS_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_MCS_MASK_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_VALID_MCS_MASK_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_MCS_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_FLAG_VALID_MCS_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_FLAG_VALID_MCS_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_GUARD_INTERVAL_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_GUARD_INTERVAL_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_VALID_GUARD_INTERVAL_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_GUARD_INTERVAL_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL( \
             HTT_TX_MSDU_EXT_DESC_FLAG_VALID_GUARD_INTERVAL, _val); \
         ((_var) |= ((_val) \
             << HTT_TX_MSDU_EXT_DESC_FLAG_VALID_GUARD_INTERVAL_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PREAMBLE_TYPE_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PREAMBLE_TYPE_MASK_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PREAMBLE_TYPE_MASK_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PREAMBLE_TYPE_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL( \
             HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PREAMBLE_TYPE_MASK, _val); \
         ((_var) |= ((_val) \
             << HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PREAMBLE_TYPE_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_CHAIN_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_CHAIN_MASK_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_VALID_CHAIN_MASK_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_CHAIN_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_FLAG_VALID_CHAIN_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_FLAG_VALID_CHAIN_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_RETRIES_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_RETRIES_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_VALID_RETRIES_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_RETRIES_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_FLAG_VALID_RETRIES, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_FLAG_VALID_RETRIES_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_BANDWIDTH_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_BANDWIDTH_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_VALID_BANDWIDTH_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_BANDWIDTH_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_FLAG_VALID_BANDWIDTH, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_FLAG_VALID_BANDWIDTH_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_EXPIRE_TIME_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_EXPIRE_TIME_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_VALID_EXPIRE_TIME_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_VALID_EXPIRE_TIME_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_FLAG_VALID_EXPIRE_TIME, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_FLAG_VALID_EXPIRE_TIME_S));\
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_FLAG_IS_DSRC_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_IS_DSRC_M) >> \
    HTT_TX_MSDU_EXT_DESC_FLAG_IS_DSRC_S)
#define HTT_TX_MSDU_EXT_DESC_FLAG_IS_DSRC_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_FLAG_IS_DSRC, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_FLAG_IS_DSRC_S)); \
     } while (0)


/* DWORD 1 */
#define HTT_TX_MSDU_EXT_DESC_PWR_GET_BASE(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_PWR_M) >> \
    HTT_TX_MSDU_EXT_DESC_PWR_S)
#define HTT_TX_MSDU_EXT_DESC_PWR_GET(_var) \
    (HTT_TX_MSDU_EXT_DESC_PWR_GET_BASE(_var)  | \
    HTT_SIGN_BIT_EXTENSION_MASK(_var, HTT_TX_MSDU_EXT_DESC_PWR))
#define HTT_TX_MSDU_EXT_DESC_PWR_SET(_var, _val) \
    ((_var) |= (((_val) << HTT_TX_MSDU_EXT_DESC_PWR_S)) & \
    HTT_TX_MSDU_EXT_DESC_PWR_M)

#define HTT_TX_MSDU_EXT_DESC_MCS_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_MCS_MASK_M) >> \
    HTT_TX_MSDU_EXT_DESC_MCS_MASK_S)
#define HTT_TX_MSDU_EXT_DESC_MCS_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_MCS_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_MCS_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_NSS_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_NSS_MASK_M) >> \
    HTT_TX_MSDU_EXT_DESC_NSS_MASK_S)
#define HTT_TX_MSDU_EXT_DESC_NSS_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_NSS_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_NSS_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_GUARD_INTERVAL_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_GUARD_INTERVAL_M) >> \
    HTT_TX_MSDU_EXT_DESC_GUARD_INTERVAL_S)
#define HTT_TX_MSDU_EXT_DESC_GUARD_INTERVAL_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_GUARD_INTERVAL, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_GUARD_INTERVAL_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_PREAMBLE_TYPE_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_PREAMBLE_TYPE_MASK_M) >> \
    HTT_TX_MSDU_EXT_DESC_PREAMBLE_TYPE_MASK_S)
#define HTT_TX_MSDU_EXT_DESC_PREAMBLE_TYPE_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_PREAMBLE_TYPE_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_PREAMBLE_TYPE_MASK_S)); \
     } while (0)


/* DWORD 2 */
#define HTT_TX_MSDU_EXT_DESC_CHAIN_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_CHAIN_MASK_M) >> \
    HTT_TX_MSDU_EXT_DESC_CHAIN_MASK_S)
#define HTT_TX_MSDU_EXT_DESC_CHAIN_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_CHAIN_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_CHAIN_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_RETRY_LIMIT_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_RETRY_LIMIT_M) >> \
    HTT_TX_MSDU_EXT_DESC_RETRY_LIMIT_S)
#define HTT_TX_MSDU_EXT_DESC_RETRY_LIMIT_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_RETRY_LIMIT, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_RETRY_LIMIT_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT_DESC_BANDWIDTH_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_BANDWIDTH_MASK_M) >> \
    HTT_TX_MSDU_EXT_DESC_BANDWIDTH_MASK_S)
#define HTT_TX_MSDU_EXT_DESC_BANDWIDTH_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT_DESC_BANDWIDTH_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT_DESC_BANDWIDTH_MASK_S)); \
     } while (0)


typedef enum {
    HTT_11AX_HE_LTF_SUBTYPE_1X,
    HTT_11AX_HE_LTF_SUBTYPE_2X,
    HTT_11AX_HE_LTF_SUBTYPE_4X,
} htt_11ax_ltf_subtype_t;

typedef enum {
    HTT_TX_MSDU_EXT2_DESC_PREAM_OFDM,
    HTT_TX_MSDU_EXT2_DESC_PREAM_CCK,
    HTT_TX_MSDU_EXT2_DESC_PREAM_HT ,
    HTT_TX_MSDU_EXT2_DESC_PREAM_VHT,
    HTT_TX_MSDU_EXT2_DESC_PREAM_HE_SU,
    HTT_TX_MSDU_EXT2_DESC_PREAM_HE_EXT_SU,
} htt_tx_ext2_preamble_type_t;

#define HTT_TX_MSDU_EXT2_DESC_BW_5MHZ_M      0x00000001
#define HTT_TX_MSDU_EXT2_DESC_BW_5MHZ_S      0
#define HTT_TX_MSDU_EXT2_DESC_BW_10MHZ_M     0x00000002
#define HTT_TX_MSDU_EXT2_DESC_BW_10MHZ_S     1
#define HTT_TX_MSDU_EXT2_DESC_BW_20MHZ_M     0x00000004
#define HTT_TX_MSDU_EXT2_DESC_BW_20MHZ_S     2
#define HTT_TX_MSDU_EXT2_DESC_BW_40MHZ_M     0x00000008
#define HTT_TX_MSDU_EXT2_DESC_BW_40MHZ_S     3
#define HTT_TX_MSDU_EXT2_DESC_BW_80MHZ_M     0x00000010
#define HTT_TX_MSDU_EXT2_DESC_BW_80MHZ_S     4
#define HTT_TX_MSDU_EXT2_DESC_BW_160MHZ_M    0x00000020
#define HTT_TX_MSDU_EXT2_DESC_BW_160MHZ_S    5

/**
 * @brief HTT tx MSDU extension descriptor v2
 * @details
 *  In Lithium, if htt_tx_tcl_metadata->valid_htt_ext is set, this structure
 *  is received as tcl_exit_base->host_meta_info in firmware.
 *  Also there is no htt_tx_msdu_desc_t in Lithium since most of those fields
 *  are already part of tcl_exit_base.
 */
PREPACK struct htt_tx_msdu_desc_ext2_t {
    /* DWORD 0: flags */
    A_UINT32
        valid_pwr            : 1, /*  if set, tx pwr spec is valid */
        valid_mcs_mask       : 1, /*  if set, tx MCS mask is valid */
        valid_nss_mask       : 1, /*  if set, tx Nss mask is valid */
        valid_preamble_type  : 1, /*  if set, tx preamble spec is valid */
        valid_retries        : 1, /*  if set, tx retries spec is valid */
        valid_bw_info        : 1, /*  if set, tx dyn_bw and bw_mask are valid */
        valid_guard_interval : 1, /*  if set, tx guard intv spec is valid */
        valid_chainmask      : 1, /*  if set, tx chainmask is valid */
        valid_encrypt_type   : 1, /*  if set, encrypt type is valid */
        valid_key_flags      : 1, /*  if set, key flags is valid */
        valid_expire_tsf     : 1, /*  if set, tx expire TSF spec is valid */
        valid_chanfreq       : 1, /*  if set, chanfreq is valid */
        is_dsrc              : 1, /*  if set, MSDU is a DSRC frame */
        guard_interval       : 2, /*  0.4us, 0.8us, 1.6us, 3.2us */
        encrypt_type         : 2, /*  0 = NO_ENCRYPT,
                                      1 = ENCRYPT,
                                      2 ~ 3 - Reserved */
        /* retry_limit -
         * Specify the maximum number of transmissions, including the
         * initial transmission, to attempt before giving up if no ack
         * is received.
         * If the tx rate is specified, then all retries shall use the
         * same rate as the initial transmission.
         * If no tx rate is specified, the target can choose whether to
         * retain the original rate during the retransmissions, or to
         * fall back to a more robust rate.
         */
        retry_limit          : 4,
        use_dcm_11ax         : 1, /* If set, Use Dual subcarrier modulation.
                                   * Valid only for 11ax preamble types HE_SU
                                   * and HE_EXT_SU
                                   */
        ltf_subtype_11ax     : 2, /* Takes enum values of htt_11ax_ltf_subtype_t
                                   * Valid only for 11ax preamble types HE_SU
                                   * and HE_EXT_SU
                                   */
        dyn_bw               : 1, /* 0 = static bw, 1 = dynamic bw */
        bw_mask              : 6, /* Valid only if dyn_bw == 0 (static bw).
                                   * (Bit mask of 5, 10, 20, 40, 80, 160Mhz.
                                   * Refer to HTT_TX_MSDU_EXT2_DESC_BW defs.)
                                   */
        host_tx_desc_pool    : 1; /* If set, Firmware allocates tx_descriptors
                                   * in WAL_BUFFERID_TX_HOST_DATA_EXP,instead
                                   * of WAL_BUFFERID_TX_TCL_DATA_EXP.
                                   * Use cases:
                                   * Any time firmware uses TQM-BYPASS for Data
                                   * TID, firmware expect host to set this bit.
                                   */

    /* DWORD 1: tx power, tx rate */
    A_UINT32
        power                : 8,   /* unit of the power field is 0.5 dbm
                                     * similar to pwr field in htt_tx_msdu_desc_ext_t
                                     * signed value ranging from -64dbm to 63.5 dbm
                                     */
        mcs_mask             : 12,  /* mcs bit mask of 0 ~ 11
                                     * Setting more than one MCS isn't currently
                                     * supported by the target (but is supported
                                     * in the interface in case in the future
                                     * the target supports specifications of
                                     * a limited set of MCS values.
                                     */
        nss_mask             : 8,   /* Nss bit mask 0 ~ 7
                                     * Setting more than one Nss isn't currently
                                     * supported by the target (but is supported
                                     * in the interface in case in the future
                                     * the target supports specifications of
                                     * a limited set of Nss values.
                                     */
        pream_type           : 3,   /* Takes enum values of htt_tx_ext2_preamble_type_t */
        update_peer_cache    : 1;   /* When set these custom values will be
                                     * used for all packets, until the next
                                     * update via this ext header.
                                     * This is to make sure not all packets
                                     * need to include this header.
                                     */

    /* DWORD 2: tx chain mask, tx retries */
    A_UINT32
        /* chain_mask - specify which chains to transmit from */
        chain_mask         : 8,

        key_flags          : 8,  /* Key Index and related flags - used in mesh mode
                                  * TODO: Update Enum values for key_flags
                                  */

        /*
         * Channel frequency: This identifies the desired channel
         * frequency (in MHz) for tx frames. This is used by FW to help
         * determine when it is safe to transmit or drop frames for
         * off-channel operation.
         * The default value of zero indicates to FW that the corresponding
         * VDEV's home channel (if there is one) is the desired channel
         * frequency.
         */
        chanfreq           : 16;

    /* DWORD 3: tx expiry time (TSF) LSBs */
    A_UINT32 expire_tsf_lo;

    /* DWORD 4: tx expiry time (TSF) MSBs */
    A_UINT32 expire_tsf_hi;

    /* DWORD 5: flags to control routing / processing of the MSDU */
    A_UINT32
        /* learning_frame
         * When this flag is set, this frame will be dropped by FW
         * rather than being enqueued to the Transmit Queue Manager (TQM) HW.
         */
        learning_frame       :  1,
        /* send_as_standalone
         * This will indicate if the msdu needs to be sent as a singleton PPDU,
         * i.e. with no A-MSDU or A-MPDU aggregation.
         * The scope is extended to other use-cases.
         */
        send_as_standalone   :  1,
        /* is_host_opaque_valid
         * Host should set this bit to 1 if the host_opaque_cookie is populated
         * with valid information.
         */
        is_host_opaque_valid :  1,
        rsvd0                : 29;

    /* DWORD 6 : Host opaque cookie for special frames */
    A_UINT32 host_opaque_cookie  : 16, /* see is_host_opaque_valid */
             rsvd1               : 16;

    /*
     * This structure can be expanded further up to 40 bytes
     * by adding further DWORDs as needed.
     */
} POSTPACK;

/* DWORD 0 */
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PWR_M                0x00000001
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PWR_S                0
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_MCS_MASK_M           0x00000002
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_MCS_MASK_S           1
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_NSS_MASK_M           0x00000004
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_NSS_MASK_S           2
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PREAMBLE_TYPE_M      0x00000008
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PREAMBLE_TYPE_S      3
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_RETRIES_M            0x00000010
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_RETRIES_S            4
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_BW_INFO_M            0x00000020
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_BW_INFO_S            5
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_GUARD_INTERVAL_M     0x00000040
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_GUARD_INTERVAL_S     6
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHAIN_MASK_M         0x00000080
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHAIN_MASK_S         7
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_ENCRYPT_TYPE_M       0x00000100
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_ENCRYPT_TYPE_S       8
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_KEY_FLAGS_M          0x00000200
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_KEY_FLAGS_S          9
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_EXPIRE_TIME_M        0x00000400
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_EXPIRE_TIME_S        10
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHANFREQ_M           0x00000800
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHANFREQ_S           11
#define HTT_TX_MSDU_EXT2_DESC_FLAG_IS_DSRC_M                  0x00001000
#define HTT_TX_MSDU_EXT2_DESC_FLAG_IS_DSRC_S                  12
#define HTT_TX_MSDU_EXT2_DESC_GUARD_INTERVAL_M                0x00006000
#define HTT_TX_MSDU_EXT2_DESC_GUARD_INTERVAL_S                13
#define HTT_TX_MSDU_EXT2_DESC_ENCRYPT_TYPE_M                  0x00018000
#define HTT_TX_MSDU_EXT2_DESC_ENCRYPT_TYPE_S                  15
#define HTT_TX_MSDU_EXT2_DESC_RETRY_LIMIT_M                   0x001e0000
#define HTT_TX_MSDU_EXT2_DESC_RETRY_LIMIT_S                   17
#define HTT_TX_MSDU_EXT2_DESC_USE_DCM_11AX_M                  0x00200000
#define HTT_TX_MSDU_EXT2_DESC_USE_DCM_11AX_S                  21
#define HTT_TX_MSDU_EXT2_DESC_LTF_SUBTYPE_11AX_M              0x00c00000
#define HTT_TX_MSDU_EXT2_DESC_LTF_SUBTYPE_11AX_S              22
#define HTT_TX_MSDU_EXT2_DESC_DYN_BW_M                        0x01000000
#define HTT_TX_MSDU_EXT2_DESC_DYN_BW_S                        24
#define HTT_TX_MSDU_EXT2_DESC_BW_MASK_M                       0x7e000000
#define HTT_TX_MSDU_EXT2_DESC_BW_MASK_S                       25

/* DWORD 1 */
#define HTT_TX_MSDU_EXT2_DESC_PWR_M                           0x000000ff
#define HTT_TX_MSDU_EXT2_DESC_PWR_S                           0
#define HTT_TX_MSDU_EXT2_DESC_MCS_MASK_M                      0x000fff00
#define HTT_TX_MSDU_EXT2_DESC_MCS_MASK_S                      8
#define HTT_TX_MSDU_EXT2_DESC_NSS_MASK_M                      0x0ff00000
#define HTT_TX_MSDU_EXT2_DESC_NSS_MASK_S                      20
#define HTT_TX_MSDU_EXT2_DESC_PREAM_TYPE_M                    0x70000000
#define HTT_TX_MSDU_EXT2_DESC_PREAM_TYPE_S                    28
#define HTT_TX_MSDU_EXT2_DESC_UPDATE_PEER_CACHE_M             0x80000000
#define HTT_TX_MSDU_EXT2_DESC_UPDATE_PEER_CACHE_S             31

/* DWORD 2 */
#define HTT_TX_MSDU_EXT2_DESC_CHAIN_MASK_M                    0x000000ff
#define HTT_TX_MSDU_EXT2_DESC_CHAIN_MASK_S                    0
#define HTT_TX_MSDU_EXT2_DESC_KEY_FLAGS_M                     0x0000ff00
#define HTT_TX_MSDU_EXT2_DESC_KEY_FLAGS_S                     8
#define HTT_TX_MSDU_EXT_DESC_CHANFREQ_M                       0xffff0000
#define HTT_TX_MSDU_EXT_DESC_CHANFREQ_S                       16

/* DWORD 5 */
#define HTT_TX_MSDU_EXT2_DESC_FLAG_LEARNING_FRAME_M           0x00000001
#define HTT_TX_MSDU_EXT2_DESC_FLAG_LEARNING_FRAME_S           0
#define HTT_TX_MSDU_EXT2_DESC_FLAG_SEND_AS_STANDALONE_M       0x00000002
#define HTT_TX_MSDU_EXT2_DESC_FLAG_SEND_AS_STANDALONE_S       1
#define HTT_TX_MSDU_EXT2_DESC_FLAG_HOST_OPAQUE_VALID_M        0x00000004
#define HTT_TX_MSDU_EXT2_DESC_FLAG_HOST_OPAQUE_VALID_S        2

/* DWORD 6 */
#define HTT_TX_MSDU_EXT2_DESC_HOST_OPAQUE_COOKIE_M            0x0000FFFF
#define HTT_TX_MSDU_EXT2_DESC_HOST_OPAQUE_COOKIE_S            0


/* DWORD 0 */
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PWR_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT_DESC_FLAG_VALID_PWR_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PWR_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PWR_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PWR, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PWR_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_MCS_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_MCS_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_MCS_MASK_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_MCS_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_MCS_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_MCS_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_NSS_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_NSS_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_NSS_MASK_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_NSS_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_NSS_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_NSS_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PREAMBLE_TYPE_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PREAMBLE_TYPE_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PREAMBLE_TYPE_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PREAMBLE_TYPE_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL( \
             HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PREAMBLE_TYPE, _val); \
         ((_var) |= ((_val) \
             << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_PREAMBLE_TYPE_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_RETRIES_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_RETRIES_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_RETRIES_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_RETRIES_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_RETRIES, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_RETRIES_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_BW_INFO_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_BW_INFO_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_BW_INFO_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_BW_INFO_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_BW_INFO, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_BW_INFO_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_GUARD_INTERVAL_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_GUARD_INTERVAL_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_GUARD_INTERVAL_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_GUARD_INTERVAL_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL( \
             HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_GUARD_INTERVAL, _val); \
         ((_var) |= ((_val) \
             << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_GUARD_INTERVAL_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHAIN_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHAIN_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHAIN_MASK_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHAIN_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHAIN_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHAIN_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_ENCRYPT_TYPE_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_ENCRYPT_TYPE_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_ENCRYPT_TYPE_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_ENCRYPT_TYPE_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_ENCRYPT_TYPE, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_ENCRYPT_TYPE_S));\
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_KEY_FLAGS_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_KEY_FLAGS_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_KEY_FLAGS_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_KEY_FLAGS_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_KEY_FLAGS, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_KEY_FLAGS_S));\
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_EXPIRE_TIME_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_EXPIRE_TIME_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_EXPIRE_TIME_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_EXPIRE_TIME_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_EXPIRE_TIME, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_EXPIRE_TIME_S));\
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHANFREQ_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHANFREQ_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHANFREQ_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHANFREQ_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHANFREQ, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_VALID_CHANFREQ_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_IS_DSRC_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_IS_DSRC_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_IS_DSRC_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_IS_DSRC_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_IS_DSRC, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_IS_DSRC_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_GUARD_INTERVAL_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_GUARD_INTERVAL_M) >> \
    HTT_TX_MSDU_EXT2_DESC_GUARD_INTERVAL_S)
#define HTT_TX_MSDU_EXT2_DESC_GUARD_INTERVAL_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_GUARD_INTERVAL, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_GUARD_INTERVAL_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_ENCRYPT_TYPE_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_ENCRYPT_TYPE_M) >> \
    HTT_TX_MSDU_EXT2_DESC_ENCRYPT_TYPE_S)
#define HTT_TX_MSDU_EXT2_DESC_ENCRYPT_TYPE_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_ENCRYPT_TYPE, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_ENCRYPT_TYPE_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_RETRY_LIMIT_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_RETRY_LIMIT_M) >> \
    HTT_TX_MSDU_EXT2_DESC_RETRY_LIMIT_S)
#define HTT_TX_MSDU_EXT2_DESC_RETRY_LIMIT_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_RETRY_LIMIT, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_RETRY_LIMIT_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_USE_DCM_11AX_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_USE_DCM_11AX_M) >> \
    HTT_TX_MSDU_EXT2_DESC_USE_DCM_11AX_S)
#define HTT_TX_MSDU_EXT2_DESC_USE_DCM_11AX_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_USE_DCM_11AX, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_USE_DCM_11AX_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_LTF_SUBTYPE_11AX_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_LTF_SUBTYPE_11AX_M) >> \
    HTT_TX_MSDU_EXT2_DESC_LTF_SUBTYPE_11AX_S)
#define HTT_TX_MSDU_EXT2_DESC_LTF_SUBTYPE_11AX_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_LTF_SUBTYPE_11AX, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_LTF_SUBTYPE_11AX_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_BW_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_BW_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_BW_MASK_S)
#define HTT_TX_MSDU_EXT2_DESC_BW_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_BW_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_BW_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_PARTIAL_BW_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_PARTIAL_BW_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_PARTIAL_BW_MASK_S)
#define HTT_TX_MSDU_EXT2_DESC_PARTIAL_BW_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_PARTIAL_BW_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_PARTIAL_BW_MASK_S)); \
     } while (0)

/* DWORD 1 */
#define HTT_TX_MSDU_EXT2_DESC_PWR_GET_BASE(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_PWR_M) >> \
    HTT_TX_MSDU_EXT2_DESC_PWR_S)
#define HTT_TX_MSDU_EXT2_DESC_PWR_GET(_var) \
    (HTT_TX_MSDU_EXT2_DESC_PWR_GET_BASE(_var)  | \
    HTT_SIGN_BIT_EXTENSION_MASK(_var, HTT_TX_MSDU_EXT2_DESC_PWR))
#define HTT_TX_MSDU_EXT2_DESC_PWR_SET(_var, _val) \
    ((_var) |= (((_val) << HTT_TX_MSDU_EXT2_DESC_PWR_S)) & \
    HTT_TX_MSDU_EXT2_DESC_PWR_M)

#define HTT_TX_MSDU_EXT2_DESC_MCS_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_MCS_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_MCS_MASK_S)
#define HTT_TX_MSDU_EXT2_DESC_MCS_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_MCS_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_MCS_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_NSS_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_NSS_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_NSS_MASK_S)
#define HTT_TX_MSDU_EXT2_DESC_NSS_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_NSS_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_NSS_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_PREAMBLE_TYPE_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_PREAMBLE_TYPE_M) >> \
    HTT_TX_MSDU_EXT2_DESC_PREAMBLE_TYPE_S)
#define HTT_TX_MSDU_EXT2_DESC_PREAMBLE_TYPE_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_PREAMBLE_TYPE, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_PREAMBLE_TYPE_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_UPDATE_PEER_CACHE_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_UPDATE_PEER_CACHE_M) >> \
    HTT_TX_MSDU_EXT2_UPDATE_PEER_CACHE_S)
#define HTT_TX_MSDU_EXT2_UPDATE_PEER_CACHE_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_UPDATE_PEER_CACHE, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_UPDATE_PEER_CACHE_S)); \
     } while (0)

/* DWORD 2 */
#define HTT_TX_MSDU_EXT2_DESC_CHAIN_MASK_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_CHAIN_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_CHAIN_MASK_S)
#define HTT_TX_MSDU_EXT2_DESC_CHAIN_MASK_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_CHAIN_MASK, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_CHAIN_MASK_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_KEY_FLAGS_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_KEY_FLAGS_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_KEY_FLAGS_S)
#define HTT_TX_MSDU_EXT2_DESC_KEY_FLAGS_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_KEY_FLAGS, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_KEY_FLAGS_S)); \
     } while (0)

#define HTT_TX_MSDU_EXT2_DESC_CHANFREQ_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_CHANFREQ_MASK_M) >> \
    HTT_TX_MSDU_EXT2_DESC_CHANFREQ_S)
#define HTT_TX_MSDU_EXT2_DESC_CHANFREQ_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_CHANFREQ, _val); \
         ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_CHANFREQ_S)); \
     } while (0)

/* DWORD 5 */
#define HTT_TX_MSDU_EXT2_DESC_FLAG_LEARNING_FRAME_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_LEARNING_FRAME_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_LEARNING_FRAME_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_LEARNING_FRAME_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_LEARNING_FRAME, _val); \
        ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_LEARNING_FRAME_S)); \
    } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_SEND_AS_STANDALONE_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_SEND_AS_STANDALONE_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_SEND_AS_STANDALONE_S)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_SEND_AS_STANDALONE_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_SEND_AS_STANDALONE, _val); \
        ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_SEND_AS_STANDALONE_S)); \
    } while (0)

#define HTT_TX_MSDU_EXT2_DESC_FLAG_HOST_OPAQUE_VALID_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_FLAG_HOST_OPAQUE_VALID_M) >> \
    HTT_TX_MSDU_EXT2_DESC_FLAG_HOST_OPAQUE_VALID_S)
#define HTT_TX_MSDU_EXT2_DESC_FLAG_HOST_OPAQUE_VALID_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_FLAG_HOST_OPAQUE_VALID, _val); \
        ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_FLAG_HOST_OPAQUE_VALID_S)); \
    } while (0)

/* DWORD 6 */
#define HTT_TX_MSDU_EXT2_DESC_HOST_OPAQUE_COOKIE_GET(_var) \
    (((_var) & HTT_TX_MSDU_EXT2_DESC_HOST_OPAQUE_COOKIE_M) >> \
    HTT_TX_MSDU_EXT2_DESC_HOST_OPAQUE_COOKIE_S)
#define HTT_TX_MSDU_EXT2_DESC_HOST_OPAQUE_COOKIE_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_TX_MSDU_EXT2_DESC_HOST_OPAQUE_COOKIE, _val); \
        ((_var) |= ((_val) << HTT_TX_MSDU_EXT2_DESC_HOST_OPAQUE_COOKIE_S)); \
    } while (0)


typedef enum {
    HTT_TCL_METADATA_TYPE_PEER_BASED = 0,
    HTT_TCL_METADATA_TYPE_VDEV_BASED = 1,
} htt_tcl_metadata_type;

/**
 * @brief HTT TCL command number format
 * @details
 *  This structure is passed from host as tcl_data_cmd->tcl_cmd_number and
 *  available to firmware as tcl_exit_base->tcl_status_number.
 *  For regular / multicast packets host will send vdev and mac id and for
 *  NAWDS packets, host will send peer id.
 *  A_UINT32 is used to avoid endianness conversion problems.
 *  tcl_status_number size is 16 bits, hence only 16 bits can be used.
 */

typedef struct {
    A_UINT32
        type: 1, /* vdev_id based or peer_id based */
        rsvd: 31;
} htt_tx_tcl_vdev_or_peer_t;

typedef struct {
    A_UINT32
        type:          1, /* vdev_id based or peer_id based */
        valid_htt_ext: 1, /* If set, tcl_exit_base->host_meta_info is valid */
        vdev_id:       8,
        pdev_id:       2,
        host_inspected:1,
        rsvd:          19;
} htt_tx_tcl_vdev_metadata;

typedef struct {
    A_UINT32
        type:          1, /* vdev_id based or peer_id based */
        valid_htt_ext: 1, /* If set, tcl_exit_base->host_meta_info is valid */
        peer_id:       14,
        rsvd:          16;
} htt_tx_tcl_peer_metadata;

PREPACK struct htt_tx_tcl_metadata {
    union {
        htt_tx_tcl_vdev_or_peer_t vdev_or_peer;
        htt_tx_tcl_vdev_metadata vdev_meta;
        htt_tx_tcl_peer_metadata peer_meta;
    };
} POSTPACK;

/* DWORD 0 */
#define HTT_TX_TCL_METADATA_TYPE_M                0x00000001
#define HTT_TX_TCL_METADATA_TYPE_S                0
#define HTT_TX_TCL_METADATA_VALID_HTT_M           0x00000002
#define HTT_TX_TCL_METADATA_VALID_HTT_S           1

/* VDEV metadata */
#define HTT_TX_TCL_METADATA_VDEV_ID_M             0x000003fc
#define HTT_TX_TCL_METADATA_VDEV_ID_S             2
#define HTT_TX_TCL_METADATA_PDEV_ID_M             0x00000c00
#define HTT_TX_TCL_METADATA_PDEV_ID_S             10
#define HTT_TX_TCL_METADATA_HOST_INSPECTED_M      0x00001000
#define HTT_TX_TCL_METADATA_HOST_INSPECTED_S      12

/* PEER metadata */
#define HTT_TX_TCL_METADATA_PEER_ID_M             0x0000fffc
#define HTT_TX_TCL_METADATA_PEER_ID_S             2

#define HTT_TX_TCL_METADATA_TYPE_GET(_var) \
    (((_var) & HTT_TX_TCL_METADATA_TYPE_M) >> \
    HTT_TX_TCL_METADATA_TYPE_S)
#define HTT_TX_TCL_METADATA_TYPE_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_TCL_METADATA_TYPE, _val); \
         ((_var) |= ((_val) << HTT_TX_TCL_METADATA_TYPE_S)); \
     } while (0)

#define HTT_TX_TCL_METADATA_VALID_HTT_GET(_var) \
    (((_var) & HTT_TX_TCL_METADATA_VALID_HTT_M) >> \
    HTT_TX_TCL_METADATA_VALID_HTT_S)
#define HTT_TX_TCL_METADATA_VALID_HTT_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_TCL_METADATA_VALID_HTT, _val); \
         ((_var) |= ((_val) << HTT_TX_TCL_METADATA_VALID_HTT_S)); \
     } while (0)

#define HTT_TX_TCL_METADATA_VDEV_ID_GET(_var) \
    (((_var) & HTT_TX_TCL_METADATA_VDEV_ID_M) >> \
    HTT_TX_TCL_METADATA_VDEV_ID_S)
#define HTT_TX_TCL_METADATA_VDEV_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_TCL_METADATA_VDEV_ID, _val); \
         ((_var) |= ((_val) << HTT_TX_TCL_METADATA_VDEV_ID_S)); \
     } while (0)

#define HTT_TX_TCL_METADATA_PDEV_ID_GET(_var) \
    (((_var) & HTT_TX_TCL_METADATA_PDEV_ID_M) >> \
    HTT_TX_TCL_METADATA_PDEV_ID_S)
#define HTT_TX_TCL_METADATA_PDEV_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_TCL_METADATA_PDEV_ID, _val); \
         ((_var) |= ((_val) << HTT_TX_TCL_METADATA_PDEV_ID_S)); \
     } while (0)

#define HTT_TX_TCL_METADATA_HOST_INSPECTED_GET(_var) \
    (((_var) & HTT_TX_TCL_METADATA_HOST_INSPECTED_M) >> \
    HTT_TX_TCL_METADATA_HOST_INSPECTED_S)
#define HTT_TX_TCL_METADATA_HOST_INSPECTED_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_TCL_METADATA_HOST_INSPECTED, _val); \
         ((_var) |= ((_val) << HTT_TX_TCL_METADATA_HOST_INSPECTED_S)); \
     } while (0)

#define HTT_TX_TCL_METADATA_PEER_ID_GET(_var) \
    (((_var) & HTT_TX_TCL_METADATA_PEER_ID_M) >> \
    HTT_TX_TCL_METADATA_PEER_ID_S)
#define HTT_TX_TCL_METADATA_PEER_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_TCL_METADATA_PEER_ID, _val); \
         ((_var) |= ((_val) << HTT_TX_TCL_METADATA_PEER_ID_S)); \
     } while (0)


typedef enum {
   HTT_TX_FW2WBM_TX_STATUS_OK,
   HTT_TX_FW2WBM_TX_STATUS_DROP,
   HTT_TX_FW2WBM_TX_STATUS_TTL,
   HTT_TX_FW2WBM_TX_STATUS_REINJECT,
   HTT_TX_FW2WBM_TX_STATUS_INSPECT,
   HTT_TX_FW2WBM_TX_STATUS_MEC_NOTIFY,

   HTT_TX_FW2WBM_TX_STATUS_MAX
} htt_tx_fw2wbm_tx_status_t;

typedef enum {
   HTT_TX_FW2WBM_REINJECT_REASON_EAPOL_ENCAP_EXP, /* deprecated */
   HTT_TX_FW2WBM_REINJECT_REASON_RAW_ENCAP_EXP /* current */ =
       HTT_TX_FW2WBM_REINJECT_REASON_EAPOL_ENCAP_EXP,
   HTT_TX_FW2WBM_REINJECT_REASON_INJECT_VIA_EXP,
   HTT_TX_FW2WBM_REINJECT_REASON_MCAST,
   HTT_TX_FW2WBM_REINJECT_REASON_ARP,
   HTT_TX_FW2WBM_REINJECT_REASON_DHCP,
   HTT_TX_FW2WBM_REINJECT_REASON_FLOW_CONTROL,

   HTT_TX_FW2WBM_REINJECT_REASON_MAX,
} htt_tx_fw2wbm_reinject_reason_t;

/**
 * @brief HTT TX WBM Completion from firmware to host
 * @details
 *  This structure is passed from firmware to host overlayed on wbm_release_ring
 *  DWORD 3 and 4 for software based completions (Exception frames and
 *  TQM bypass frames)
 *  For software based completions, wbm_release_ring->release_source_module will
 *  be set to release_source_fw
 */
PREPACK struct htt_tx_wbm_completion {
    A_UINT32
        sch_cmd_id:      24,
        exception_frame: 1, /* If set, this packet was queued via exception path */
        rsvd0_31_25:     7;

    A_UINT32
        ack_frame_rssi:  8,  /* If this frame is removed as the result of the
                              * reception of an ACK or BA, this field indicates
                              * the RSSI of the received ACK or BA frame.
                              * When the frame is removed as result of a direct
                              * remove command from the SW,  this field is set
                              * to 0x0 (which is never a valid value when real
                              * RSSI is available).
                              * Units: dB w.r.t noise floor
                              */
        tx_status:       4, /* Takes enum values of htt_tx_fw2wbm_tx_status_t */
        reinject_reason: 4, /* Takes enum values of htt_tx_fw2wbm_reinject_reason_t */
        rsvd1_31_16:     16;
} POSTPACK;

/* DWORD 0 */
#define HTT_TX_WBM_COMPLETION_SCH_CMD_ID_M                0x00ffffff
#define HTT_TX_WBM_COMPLETION_SCH_CMD_ID_S                0
#define HTT_TX_WBM_COMPLETION_EXP_FRAME_M                 0x01000000
#define HTT_TX_WBM_COMPLETION_EXP_FRAME_S                 24

/* DWORD 1 */
#define HTT_TX_WBM_COMPLETION_ACK_RSSI_M                  0x000000ff
#define HTT_TX_WBM_COMPLETION_ACK_RSSI_S                  0
#define HTT_TX_WBM_COMPLETION_TX_STATUS_M                 0x00000f00
#define HTT_TX_WBM_COMPLETION_TX_STATUS_S                 8
#define HTT_TX_WBM_COMPLETION_REINJECT_REASON_M           0x0000f000
#define HTT_TX_WBM_COMPLETION_REINJECT_REASON_S           12

/* DWORD 0 */
#define HTT_TX_WBM_COMPLETION_SCH_CMD_ID_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_SCH_CMD_ID_M) >> \
    HTT_TX_WBM_COMPLETION_SCH_CMD_ID_S)
#define HTT_TX_WBM_COMPLETION_SCH_CMD_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_SCH_CMD_ID, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_SCH_CMD_ID_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_EXP_FRAME_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_EXP_FRAME_M) >> \
    HTT_TX_WBM_COMPLETION_EXP_FRAME_S)
#define HTT_TX_WBM_COMPLETION_EXP_FRAME_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_EXP_FRAME, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_EXP_FRAME_S)); \
     } while (0)

/* DWORD 1 */
#define HTT_TX_WBM_COMPLETION_ACK_RSSI_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_ACK_RSSI_M) >> \
    HTT_TX_WBM_COMPLETION_ACK_RSSI_S)
#define HTT_TX_WBM_COMPLETION_ACK_RSSI_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_ACK_RSSI, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_ACK_RSSI_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_TX_STATUS_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_TX_STATUS_M) >> \
    HTT_TX_WBM_COMPLETION_TX_STATUS_S)
#define HTT_TX_WBM_COMPLETION_TX_STATUS_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_TX_STATUS, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_TX_STATUS_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_REINJECT_REASON_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_REINJECT_REASON_M) >> \
    HTT_TX_WBM_COMPLETION_REINJECT_REASON_S)
#define HTT_TX_WBM_COMPLETION_REINJECT_REASON_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_REINJECT_REASON, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_REINJECT_REASON_S)); \
     } while (0)

/**
 * @brief HTT TX WBM Completion from firmware to host
 * @details
 *  This structure applies only to WLAN chips that contain WLAN Buffer Mgmt
 *  (WBM) offload HW.
 *  This structure is passed from firmware to host overlayed on wbm_release_ring
 *  For software based completions, release_source_module will
 *  be set to WIFIRELEASE_SOURCE_FW_E. Host SW is expected to inspect using
 *  struct wbm_release_ring and then switch to this after looking at
 *  release_source_module.
 */
PREPACK struct htt_tx_wbm_completion_v2 {
    A_UINT32
        used_by_hw0;               /* Refer to struct wbm_release_ring */
    A_UINT32
        used_by_hw1;               /* Refer to struct wbm_release_ring */
    A_UINT32
        used_by_hw2:            9, /* Refer to struct wbm_release_ring */
        tx_status:              4, /* Takes enum values of htt_tx_fw2wbm_tx_status_t */
        reinject_reason:        4, /* Takes enum values of htt_tx_fw2wbm_reinject_reason_t */
        exception_frame:        1,
        rsvd0:                 12, /* For future use */
        used_by_hw4:            1, /* wbm_internal_error bit being used by HW */
        rsvd1:                  1; /* For future use */
    A_UINT32
        data0:                 32; /* data0,1 and 2 changes based on tx_status type
                                    * if HTT_TX_FW2WBM_TX_STATUS_OK or HTT_TX_FW2WBM_TX_STATUS_DROP
                                    * or HTT_TX_FW2WBM_TX_STATUS_TTL, struct htt_tx_wbm_transmit_status will be used.
                                    * if HTT_TX_FW2WBM_TX_STATUS_REINJECT, struct htt_tx_wbm_reinject_status will be used.
                                    * if HTT_TX_FW2WBM_TX_STATUS_MEC_NOTIFY, struct htt_tx_wbm_mec_addr_notify will be used.
                                    */
    A_UINT32
        data1:                 32;
    A_UINT32
        data2:                 32;
    A_UINT32
        used_by_hw3;               /* Refer to struct wbm_release_ring */
} POSTPACK;

/* DWORD 1, 2 and part of 3 are accessed via HW header files */
/* DWORD 3 */
#define HTT_TX_WBM_COMPLETION_V2_TX_STATUS_M                 0x00001e00
#define HTT_TX_WBM_COMPLETION_V2_TX_STATUS_S                 9
#define HTT_TX_WBM_COMPLETION_V2_REINJECT_REASON_M           0x0001e000
#define HTT_TX_WBM_COMPLETION_V2_REINJECT_REASON_S           13
#define HTT_TX_WBM_COMPLETION_V2_EXP_FRAME_M                 0x00020000
#define HTT_TX_WBM_COMPLETION_V2_EXP_FRAME_S                 17

/* DWORD 3 */
#define HTT_TX_WBM_COMPLETION_V2_TX_STATUS_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_TX_STATUS_M) >> \
    HTT_TX_WBM_COMPLETION_V2_TX_STATUS_S)

#define HTT_TX_WBM_COMPLETION_V2_TX_STATUS_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_TX_STATUS, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_TX_STATUS_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_REINJECT_REASON_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_REINJECT_REASON_M) >> \
    HTT_TX_WBM_COMPLETION_V2_REINJECT_REASON_S)

#define HTT_TX_WBM_COMPLETION_V2_REINJECT_REASON_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_REINJECT_REASON, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_REINJECT_REASON_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_EXP_FRAME_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_EXP_FRAME_M) >> \
    HTT_TX_WBM_COMPLETION_V2_EXP_FRAME_S)

#define HTT_TX_WBM_COMPLETION_V2_EXP_FRAME_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_EXP_FRAME, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_EXP_FRAME_S)); \
     } while (0)

/**
 * @brief HTT TX WBM transmit status from firmware to host
 * @details
 *  This structure applies only to WLAN chips that contain WLAN Buffer Mgmt
 *  (WBM) offload HW.
 *  This structure is passed from firmware to host overlayed on wbm_release_ring.
 *  used only if tx_status is HTT_TX_FW2WBM_TX_STATUS_OK or HTT_TX_FW2WBM_TX_STATUS_DROP
 *  or HTT_TX_FW2WBM_TX_STATUS_TTL
 */
PREPACK struct htt_tx_wbm_transmit_status {
   A_UINT32
       sch_cmd_id:      24,
       ack_frame_rssi:  8;   /* If this frame is removed as the result of the
                              * reception of an ACK or BA, this field indicates
                              * the RSSI of the received ACK or BA frame.
                              * When the frame is removed as result of a direct
                              * remove command from the SW,  this field is set
                              * to 0x0 (which is never a valid value when real
                              * RSSI is available).
                              * Units: dB w.r.t noise floor
                              */
   A_UINT32
       sw_peer_id:      16,
       tid_num:          5,
       valid:            1,  /* If this "valid" flag is set, the sw_peer_id
                              * and tid_num fields contain valid data.
                              * If this "valid" flag is not set, the
                              * sw_peer_id and tid_num fields must be ignored.
                              */
       mcast:            1,
       mcast_valid:      1,  /* If this "mcast_valid" is set, the mcast field
                              * contains valid data.
                              */
       reserved0:        8;
   A_UINT32
       ppdu_start_tsf:  32;  /* PPDU Start timestamp added for multicast
                              * packets in the wbm completion path
                              */
} POSTPACK;

/* DWORD 4 */
#define HTT_TX_WBM_COMPLETION_V2_SCH_CMD_ID_M          0x00ffffff
#define HTT_TX_WBM_COMPLETION_V2_SCH_CMD_ID_S          0
#define HTT_TX_WBM_COMPLETION_V2_ACK_FRAME_RSSI_M      0xff000000
#define HTT_TX_WBM_COMPLETION_V2_ACK_FRAME_RSSI_S      24

/* DWORD 5 */
#define HTT_TX_WBM_COMPLETION_V2_SW_PEER_ID_M          0x0000ffff
#define HTT_TX_WBM_COMPLETION_V2_SW_PEER_ID_S          0
#define HTT_TX_WBM_COMPLETION_V2_TID_NUM_M             0x001f0000
#define HTT_TX_WBM_COMPLETION_V2_TID_NUM_S             16
#define HTT_TX_WBM_COMPLETION_V2_VALID_M               0x00200000
#define HTT_TX_WBM_COMPLETION_V2_VALID_S               21
#define HTT_TX_WBM_COMPLETION_V2_MCAST_M               0x00400000
#define HTT_TX_WBM_COMPLETION_V2_MCAST_S               22
#define HTT_TX_WBM_COMPLETION_V2_MCAST_VALID_M         0x00800000
#define HTT_TX_WBM_COMPLETION_V2_MCAST_VALID_S         23

/* DWORD 4 */
#define HTT_TX_WBM_COMPLETION_V2_SCH_CMD_ID_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_SCH_CMD_ID_M) >> \
    HTT_TX_WBM_COMPLETION_V2_SCH_CMD_ID_S)

#define HTT_TX_WBM_COMPLETION_V2_SCH_CMD_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_SCH_CMD_ID, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_SCH_CMD_ID_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_ACK_FRAME_RSSI_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_ACK_FRAME_RSSI_M) >> \
    HTT_TX_WBM_COMPLETION_V2_ACK_FRAME_RSSI_S)

#define HTT_TX_WBM_COMPLETION_V2_ACK_FRAME_RSSI_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_ACK_FRAME_RSSI, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_ACK_FRAME_RSSI_S)); \
     } while (0)

/* DWORD 5 */
#define HTT_TX_WBM_COMPLETION_V2_SW_PEER_ID_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_SW_PEER_ID_M) >> \
    HTT_TX_WBM_COMPLETION_V2_SW_PEER_ID_S)

#define HTT_TX_WBM_COMPLETION_V2_SW_PEER_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_SW_PEER_ID, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_SW_PEER_ID_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_TID_NUM_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_TID_NUM_M) >> \
    HTT_TX_WBM_COMPLETION_V2_TID_NUM_S)

#define HTT_TX_WBM_COMPLETION_V2_TID_NUM_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_TID_NUM, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_TID_NUM_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_VALID_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_VALID_M) >> \
    HTT_TX_WBM_COMPLETION_V2_VALID_S)

#define HTT_TX_WBM_COMPLETION_V2_VALID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_VALID, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_VALID_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_MCAST_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_MCAST_M) >> \
    HTT_TX_WBM_COMPLETION_V2_MCAST_S)

#define HTT_TX_WBM_COMPLETION_V2_MCAST_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_MCAST, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_MCAST_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_MCAST_VALID_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_MCAST_VALID_M) >> \
    HTT_TX_WBM_COMPLETION_V2_MCAST_VALID_S)

#define HTT_TX_WBM_COMPLETION_V2_MCAST_VALID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_MCAST_VALID, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_MCAST_VALID_S)); \
     } while (0)

/**
 * @brief HTT TX WBM reinject status from firmware to host
 * @details
 *  This structure applies only to WLAN chips that contain WLAN Buffer Mgmt
 *  (WBM) offload HW.
 *  This structure is passed from firmware to host overlayed on wbm_release_ring.
 *  used only if tx_status is HTT_TX_FW2WBM_TX_STATUS_REINJECT.
 */
PREPACK struct htt_tx_wbm_reinject_status {
   A_UINT32
       reserved0:       32;
   A_UINT32
       reserved1:       32;
   A_UINT32
       reserved2:       32;
} POSTPACK;

/**
 * @brief HTT TX WBM multicast echo check notification from firmware to host
 * @details
 *  This structure applies only to WLAN chips that contain WLAN Buffer Mgmt
 *  (WBM) offload HW.
 *  This structure is passed from firmware to host overlayed on wbm_release_ring.
 *  used only if tx_status is HTT_TX_FW2WBM_TX_STATUS_MEC_NOTIFY.
 *  FW sends SA addresses to host for all multicast/broadcast packets received on
 *  STA side.
 */
PREPACK struct htt_tx_wbm_mec_addr_notify {
   A_UINT32
       mec_sa_addr_31_0;
   A_UINT32
       mec_sa_addr_47_32: 16,
       sa_ast_index:      16;
   A_UINT32
       vdev_id:            8,
       reserved0:         24;

} POSTPACK;

/* DWORD 4 - mec_sa_addr_31_0 */
/* DWORD 5 */
#define HTT_TX_WBM_COMPLETION_V2_MEC_SA_ADDR_47_32_M  0x0000ffff
#define HTT_TX_WBM_COMPLETION_V2_MEC_SA_ADDR_47_32_S  0
#define HTT_TX_WBM_COMPLETION_V2_SA_AST_INDEX_M       0xffff0000
#define HTT_TX_WBM_COMPLETION_V2_SA_AST_INDEX_S       16

/* DWORD 6 */
#define HTT_TX_WBM_COMPLETION_V2_VDEV_ID_M            0x000000ff
#define HTT_TX_WBM_COMPLETION_V2_VDEV_ID_S            0

#define HTT_TX_WBM_COMPLETION_V2_MEC_SA_ADDR_47_32_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_MEC_SA_ADDR_47_32_M) >> \
    HTT_TX_WBM_COMPLETION_V2_MEC_SA_ADDR_47_32_S)

#define HTT_TX_WBM_COMPLETION_V2_MEC_SA_ADDR_47_32_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_MEC_SA_ADDR_47_32, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_MEC_SA_ADDR_47_32_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_SA_AST_INDEX_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_SA_AST_INDEX_M) >> \
    HTT_TX_WBM_COMPLETION_V2_SA_AST_INDEX_S)

#define HTT_TX_WBM_COMPLETION_V2_SA_AST_INDEX_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_SA_AST_INDEX, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_SA_AST_INDEX_S)); \
     } while (0)

#define HTT_TX_WBM_COMPLETION_V2_VDEV_ID_GET(_var) \
    (((_var) & HTT_TX_WBM_COMPLETION_V2_VDEV_ID_M) >> \
    HTT_TX_WBM_COMPLETION_V2_VDEV_ID_S)

#define HTT_TX_WBM_COMPLETION_V2_VDEV_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_WBM_COMPLETION_V2_VDEV_ID, _val); \
         ((_var) |= ((_val) << HTT_TX_WBM_COMPLETION_V2_VDEV_ID_S)); \
     } while (0)

typedef enum {
    TX_FLOW_PRIORITY_BE,
    TX_FLOW_PRIORITY_HIGH,
    TX_FLOW_PRIORITY_LOW,
} htt_tx_flow_priority_t;

typedef enum {
    TX_FLOW_LATENCY_SENSITIVE,
    TX_FLOW_LATENCY_INSENSITIVE,
} htt_tx_flow_latency_t;

typedef enum {
    TX_FLOW_BEST_EFFORT_TRAFFIC,
    TX_FLOW_INTERACTIVE_TRAFFIC,
    TX_FLOW_PERIODIC_TRAFFIC,
    TX_FLOW_BURSTY_TRAFFIC,
    TX_FLOW_OVER_SUBSCRIBED_TRAFFIC,
} htt_tx_flow_traffic_pattern_t;

/**
 * @brief HTT TX Flow search metadata format
 * @details
 *  Host will set this metadata in flow table's flow search entry along with
 *  to_tqm_if_m0_fw. It indicates to forward the first MSDU to both the
 *  firmware and TQM ring if the flow search entry wins.
 *  This metadata is available to firmware in that first MSDU's
 *  tcl_exit_base->meta_data_fse. Firmware uses this metadata to map a new flow
 *  to one of the available flows for specific tid and returns the tqm flow
 *  pointer as part of htt_tx_map_flow_info message.
 */
PREPACK struct htt_tx_flow_metadata {
    A_UINT32
        rsvd0_1_0:            2,
        tid:                  4,
        priority:             3, /* Takes enum values of htt_tx_flow_priority_t */
        traffic_pattern:      3, /* Takes enum values of htt_tx_flow_traffic_pattern_t */
        tid_override:         1, /* If set, tid field in this struct is the final tid.
                                  * Else choose final tid based on latency, priority.
                                  */
        dedicated_flowq:      1,  /* Dedicated flowq per 5 tuple flow. */
        latency_sensitive:    2,  /* Takes enum values of htt_tx_flow_latency_t */
        host_flow_identifier: 16; /* Used by host to map flow metadata with flow entry */
} POSTPACK;

/* DWORD 0 */
#define HTT_TX_FLOW_METADATA_TID_M                      0x0000003c
#define HTT_TX_FLOW_METADATA_TID_S                      2
#define HTT_TX_FLOW_METADATA_PRIORITY_M                 0x000001c0
#define HTT_TX_FLOW_METADATA_PRIORITY_S                 6
#define HTT_TX_FLOW_METADATA_TRAFFIC_PATTERN_M          0x00000e00
#define HTT_TX_FLOW_METADATA_TRAFFIC_PATTERN_S          9
#define HTT_TX_FLOW_METADATA_TID_OVERRIDE_M             0x00001000
#define HTT_TX_FLOW_METADATA_TID_OVERRIDE_S             12
#define HTT_TX_FLOW_METADATA_DEDICATED_FLOWQ_M          0x00002000
#define HTT_TX_FLOW_METADATA_DEDICATED_FLOWQ_S          13
#define HTT_TX_FLOW_METADATA_LATENCY_SENSITIVE_M        0x0000c000
#define HTT_TX_FLOW_METADATA_LATENCY_SENSITIVE_S        14
#define HTT_TX_FLOW_METADATA_HOST_FLOW_ID_M             0xffff0000
#define HTT_TX_FLOW_METADATA_HOST_FLOW_ID_S             16

/* DWORD 0 */
#define HTT_TX_FLOW_METADATA_TID_GET(_var) \
    (((_var) & HTT_TX_FLOW_METADATA_TID_M) >> \
    HTT_TX_FLOW_METADATA_TID_S)
#define HTT_TX_FLOW_METADATA_TID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_FLOW_METADATA_TID, _val); \
         ((_var) |= ((_val) << HTT_TX_FLOW_METADATA_TID_S)); \
     } while (0)

#define HTT_TX_FLOW_METADATA_PRIORITY_GET(_var) \
    (((_var) & HTT_TX_FLOW_PRIORITY_M) >> \
    HTT_TX_FLOW_METADATA_PRIORITY_S)
#define HTT_TX_FLOW_METADATA_PRIORITY_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_FLOW_METADATA_PRIORITY, _val); \
         ((_var) |= ((_val) << HTT_TX_FLOW_METADATA_PRIORITY_S)); \
     } while (0)

#define HTT_TX_FLOW_METADATA_TRAFFIC_PATTERN_GET(_var) \
    (((_var) & HTT_TX_FLOW_METADATA_TRAFFIC_PATTERN_M) >> \
    HTT_TX_FLOW_METADATA_TRAFFIC_PATTERN_S)
#define HTT_TX_FLOW_METADATA_TRAFFIC_PATTERN_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_FLOW_METADATA_TRAFFIC_PATTERN, _val); \
         ((_var) |= ((_val) << HTT_TX_FLOW_METADATA_TRAFFIC_PATTERN_S)); \
     } while (0)

#define HTT_TX_FLOW_METADATA_TID_OVERRIDE_GET(_var) \
    (((_var) & HTT_TX_FLOW_METADATA_TID_OVERRIDE_M) >> \
    HTT_TX_FLOW_METADATA_TID_OVERRIDE_S)
#define HTT_TX_FLOW_METADATA_TID_OVERRIDE_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_FLOW_METADATA_TID_OVERRIDE, _val); \
         ((_var) |= ((_val) << HTT_TX_FLOW_METADATA_TID_OVERRIDE_S)); \
     } while (0)

#define HTT_TX_FLOW_METADATA_DEDICATED_FLOWQ_GET(_var) \
    (((_var) & HTT_TX_FLOW_METADATA_DEDICATED_FLOWQ_M) >> \
    HTT_TX_FLOW_METADATA_DEDICATED_FLOWQ_S)
#define HTT_TX_FLOW_METADATA_DEDICATED_FLOWQ_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_FLOW_METADATA_DEDICATED_FLOWQ, _val); \
         ((_var) |= ((_val) << HTT_TX_FLOW_METADATA_DEDICATED_FLOWQ_S)); \
     } while (0)

#define HTT_TX_FLOW_METADATA_LATENCY_SENSITIVE_GET(_var) \
    (((_var) & HTT_TX_FLOW_METADATA_LATENCY_SENSITIVE_M) >> \
    HTT_TX_FLOW_METADATA_LATENCY_SENSITIVE_S)
#define HTT_TX_FLOW_METADATA_LATENCY_SENSITIVE_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_FLOW_LATENCY_SENSITIVE, _val); \
         ((_var) |= ((_val) << HTT_TX_FLOW_LATENCY_SENSITIVE_S)); \
     } while (0)

#define HTT_TX_FLOW_METADATA_HOST_FLOW_ID_GET(_var) \
    (((_var) & HTT_TX_FLOW_METADATA_HOST_FLOW_ID_M) >> \
    HTT_TX_FLOW_METADATA_HOST_FLOW_ID_S)
#define HTT_TX_FLOW_METADATA_HOST_FLOW_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_FLOW_METADATA_HOST_FLOW_ID, _val); \
         ((_var) |= ((_val) << HTT_TX_FLOW_METADATA_HOST_FLOW_ID_S)); \
     } while (0)


/**
 * @brief host -> target ADD WDS Entry
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_ADD_WDS_ENTRY
 *
 * @brief host -> target DELETE WDS Entry
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_DELETE_WDS_ENTRY
 *
 * @details
 *  HTT wds entry from source port learning
 *  Host will learn wds entries from rx and send this message to firmware
 *  to enable firmware to configure/delete AST entries for wds clients.
 *  Firmware creates Source address's AST entry with Transmit MAC's peer_id
 *  and when SA's entry is deleted, firmware removes this AST entry
 *
 *  The message would appear as follows:
 *
 *     |31 30|29                   |17 16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |           rsvd0           |PDVID|     vdev_id    |    msg_type    |
 *     |-------------------------------------------------------------------|
 *     |                           sa_addr_31_0                            |
 *     |-------------------------------------------------------------------|
 *     |     |       ta_peer_id          |         sa_addr_47_32           |
 *     |-------------------------------------------------------------------|
 * Where PDVID = pdev_id
 *
 *  The message is interpreted as follows:
 *
 *  dword0 - b'0:7   - msg_type: This will be set to
 *                     0xd (HTT_H2T_MSG_TYPE_ADD_WDS_ENTRY) or
 *                     0xe (HTT_H2T_MSG_TYPE_DELETE_WDS_ENTRY)
 *
 *  dword0 - b'8:15  - vdev_id
 *
 *  dword0 - b'16:17 - pdev_id
 *
 *  dword0 - b'18:31 - rsvd10: Reserved for future use
 *
 *  dword1 - b'0:31  - sa_addr_31_0: Lower 32 bits of source mac address
 *
 *  dword2 - b'0:15  - sa_addr_47_32: Upper 16 bits of source mac address
 *
 *  dword2 - b'16:19 - ta_peer_id: peer id of Transmit MAC
 */

PREPACK struct htt_wds_entry {
    A_UINT32
        msg_type: 8,
        vdev_id:  8,
        pdev_id:  2,
        rsvd0:    14;
    A_UINT32 sa_addr_31_0;
    A_UINT32
        sa_addr_47_32: 16,
        ta_peer_id:    14,
        rsvd2:         2;
} POSTPACK;

/* DWORD 0 */
#define HTT_WDS_ENTRY_VDEV_ID_M                0x0000ff00
#define HTT_WDS_ENTRY_VDEV_ID_S                8
#define HTT_WDS_ENTRY_PDEV_ID_M                0x00030000
#define HTT_WDS_ENTRY_PDEV_ID_S                16

/* DWORD 2 */
#define HTT_WDS_ENTRY_SA_ADDR_47_32_M          0x0000ffff
#define HTT_WDS_ENTRY_SA_ADDR_47_32_S          0
#define HTT_WDS_ENTRY_TA_PEER_ID_M             0x3fff0000
#define HTT_WDS_ENTRY_TA_PEER_ID_S             16

/* DWORD 0 */
#define HTT_WDS_ENTRY_VDEV_ID_GET(_var) \
    (((_var) & HTT_WDS_ENTRY_VDEV_ID_M) >> \
    HTT_WDS_ENTRY_VDEV_ID_S)
#define HTT_WDS_ENTRY_VDEV_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_WDS_ENTRY_VDEV_ID, _val); \
         ((_var) |= ((_val) << HTT_WDS_ENTRY_VDEV_ID_S)); \
     } while (0)

#define HTT_WDS_ENTRY_PDEV_ID_GET(_var) \
    (((_var) & HTT_WDS_ENTRY_PDEV_ID_M) >> \
    HTT_WDS_ENTRY_PDEV_ID_S)
#define HTT_WDS_ENTRY_PDEV_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_WDS_ENTRY_PDEV_ID, _val); \
         ((_var) |= ((_val) << HTT_WDS_ENTRY_PDEV_ID_S)); \
     } while (0)

/* DWORD 2 */
#define HTT_WDS_ENTRY_SA_ADDR_47_32_GET(_var) \
    (((_var) & HTT_WDS_ENTRY_SA_ADDR_47_32_M) >> \
    HTT_WDS_ENTRY_SA_ADDR_47_32_S)
#define HTT_WDS_ENTRY_SA_ADDR_47_32_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_WDS_ENTRY_SA_ADDR_47_32, _val); \
         ((_var) |= ((_val) << HTT_WDS_ENTRY_SA_ADDR_47_32_S)); \
     } while (0)

#define HTT_WDS_ENTRY_TA_PEER_ID_GET(_var) \
    (((_var) & HTT_WDS_ENTRY_TA_PEER_ID_M) >> \
    HTT_WDS_ENTRY_TA_PEER_ID_S)
#define HTT_WDS_ENTRY_TA_PEER_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_WDS_ENTRY_TA_PEER_ID, _val); \
         ((_var) |= ((_val) << HTT_WDS_ENTRY_TA_PEER_ID_S)); \
     } while (0)


/**
 * @brief MAC DMA rx ring setup specification
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_RX_RING_CFG
 *
 * @details
 *  To allow for dynamic rx ring reconfiguration and to avoid race
 *  conditions, the host SW never directly programs the MAC DMA rx ring(s)
 *  it uses.  Instead, it sends this message to the target, indicating how
 *  the rx ring used by the host should be set up and maintained.
 *  The message consists of a 4-octet header followed by 1 or 2 rx ring setup
 *  specifications.
 *
 *            |31                           16|15            8|7             0|
 *            |---------------------------------------------------------------|
 * header:    |            reserved           |   num rings   |    msg type   |
 *            |---------------------------------------------------------------|
 * payload 1: |       FW_IDX shadow register physical address (bits 31:0)     |
#if HTT_PADDR64
 *            |       FW_IDX shadow register physical address (bits 63:32)    |
#endif
 *            |---------------------------------------------------------------|
 *            |                 rx ring base physical address (bits 31:0)     |
#if HTT_PADDR64
 *            |                 rx ring base physical address (bits 63:32)    |
#endif
 *            |---------------------------------------------------------------|
 *            |      rx ring buffer size      |        rx ring length         |
 *            |---------------------------------------------------------------|
 *            |      FW_IDX initial value     |         enabled flags         |
 *            |---------------------------------------------------------------|
 *            |      MSDU payload offset      |     802.11 header offset      |
 *            |---------------------------------------------------------------|
 *            |        PPDU end offset        |       PPDU start offset       |
 *            |---------------------------------------------------------------|
 *            |        MPDU end offset        |       MPDU start offset       |
 *            |---------------------------------------------------------------|
 *            |        MSDU end offset        |       MSDU start offset       |
 *            |---------------------------------------------------------------|
 *            |        frag info offset       |      rx attention offset      |
 *            |---------------------------------------------------------------|
 * payload 2, if present, has the same format as payload 1
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx ring configuration message
 *     Value: 0x2 (HTT_H2T_MSG_TYPE_RX_RING_CFG)
 *   - NUM_RINGS
 *     Bits 15:8
 *     Purpose: indicates whether the host is setting up one rx ring or two
 *     Value: 1 or 2
 * Payload:
 *     for systems using 64-bit format for bus addresses:
 *       - IDX_SHADOW_REG_PADDR_LO
 *         Bits 31:0
 *         Value: lower 4 bytes of physical address of the host's
 *                FW_IDX shadow register
 *       - IDX_SHADOW_REG_PADDR_HI
 *         Bits 31:0
 *         Value: upper 4 bytes of physical address of the host's
 *                FW_IDX shadow register
 *       - RING_BASE_PADDR_LO
 *         Bits 31:0
 *         Value: lower 4 bytes of physical address of the host's rx ring
 *       - RING_BASE_PADDR_HI
 *         Bits 31:0
 *         Value: uppper 4 bytes of physical address of the host's rx ring
 *     for systems using 32-bit format for bus addresses:
 *       - IDX_SHADOW_REG_PADDR
 *         Bits 31:0
 *         Value: physical address of the host's FW_IDX shadow register
 *       - RING_BASE_PADDR
 *         Bits 31:0
 *         Value: physical address of the host's rx ring
 *   - RING_LEN
 *     Bits 15:0
 *     Value: number of elements in the rx ring
 *   - RING_BUF_SZ
 *     Bits 31:16
 *     Value: size of the buffers referenced by the rx ring, in byte units
 *   - ENABLED_FLAGS
 *     Bits 15:0
 *     Value: 1-bit flags to show whether different rx fields are enabled
 *         bit  0: 802.11 header enabled (1) or disabled (0)
 *         bit  1: MSDU payload  enabled (1) or disabled (0)
 *         bit  2: PPDU start    enabled (1) or disabled (0)
 *         bit  3: PPDU end      enabled (1) or disabled (0)
 *         bit  4: MPDU start    enabled (1) or disabled (0)
 *         bit  5: MPDU end      enabled (1) or disabled (0)
 *         bit  6: MSDU start    enabled (1) or disabled (0)
 *         bit  7: MSDU end      enabled (1) or disabled (0)
 *         bit  8: rx attention  enabled (1) or disabled (0)
 *         bit  9: frag info     enabled (1) or disabled (0)
 *         bit 10: unicast rx    enabled (1) or disabled (0)
 *         bit 11: multicast rx  enabled (1) or disabled (0)
 *         bit 12: ctrl rx       enabled (1) or disabled (0)
 *         bit 13: mgmt rx       enabled (1) or disabled (0)
 *         bit 14: null rx       enabled (1) or disabled (0)
 *         bit 15: phy data rx   enabled (1) or disabled (0)
 *   - IDX_INIT_VAL
 *     Bits 31:16
 *     Purpose: Specify the initial value for the FW_IDX.
 *     Value: the number of buffers initially present in the host's rx ring
 *   - OFFSET_802_11_HDR
 *     Bits 15:0
 *     Value: offset in QUAD-bytes of 802.11 header from the buffer start
 *   - OFFSET_MSDU_PAYLOAD
 *     Bits 31:16
 *     Value: offset in QUAD-bytes of MSDU payload from the buffer start
 *   - OFFSET_PPDU_START
 *     Bits 15:0
 *     Value: offset in QUAD-bytes of PPDU start rx desc from the buffer start
 *   - OFFSET_PPDU_END
 *     Bits 31:16
 *     Value: offset in QUAD-bytes of PPDU end rx desc from the buffer start
 *   - OFFSET_MPDU_START
 *     Bits 15:0
 *     Value: offset in QUAD-bytes of MPDU start rx desc from the buffer start
 *   - OFFSET_MPDU_END
 *     Bits 31:16
 *     Value: offset in QUAD-bytes of MPDU end rx desc from the buffer start
 *   - OFFSET_MSDU_START
 *     Bits 15:0
 *     Value: offset in QUAD-bytes of MSDU start rx desc from the buffer start
 *   - OFFSET_MSDU_END
 *     Bits 31:16
 *     Value: offset in QUAD-bytes of MSDU end rx desc from the buffer start
 *   - OFFSET_RX_ATTN
 *     Bits 15:0
 *     Value: offset in QUAD-bytes of rx attention word from the buffer start
 *   - OFFSET_FRAG_INFO
 *     Bits 31:16
 *     Value: offset in QUAD-bytes of frag info table
 */
/* header fields */
#define HTT_RX_RING_CFG_NUM_RINGS_M      0xff00
#define HTT_RX_RING_CFG_NUM_RINGS_S      8

/* payload fields */
/* for systems using a 64-bit format for bus addresses */
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_HI_M 0xffffffff
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_HI_S 0
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_LO_M 0xffffffff
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_LO_S 0
#define HTT_RX_RING_CFG_BASE_PADDR_HI_M           0xffffffff
#define HTT_RX_RING_CFG_BASE_PADDR_HI_S           0
#define HTT_RX_RING_CFG_BASE_PADDR_LO_M           0xffffffff
#define HTT_RX_RING_CFG_BASE_PADDR_LO_S           0

/* for systems using a 32-bit format for bus addresses */
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_M    0xffffffff
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_S    0
#define HTT_RX_RING_CFG_BASE_PADDR_M              0xffffffff
#define HTT_RX_RING_CFG_BASE_PADDR_S              0

#define HTT_RX_RING_CFG_LEN_M             0xffff
#define HTT_RX_RING_CFG_LEN_S             0
#define HTT_RX_RING_CFG_BUF_SZ_M          0xffff0000
#define HTT_RX_RING_CFG_BUF_SZ_S          16
#define HTT_RX_RING_CFG_ENABLED_802_11_HDR_M   0x1
#define HTT_RX_RING_CFG_ENABLED_802_11_HDR_S   0
#define HTT_RX_RING_CFG_ENABLED_MSDU_PAYLD_M   0x2
#define HTT_RX_RING_CFG_ENABLED_MSDU_PAYLD_S   1
#define HTT_RX_RING_CFG_ENABLED_PPDU_START_M   0x4
#define HTT_RX_RING_CFG_ENABLED_PPDU_START_S   2
#define HTT_RX_RING_CFG_ENABLED_PPDU_END_M     0x8
#define HTT_RX_RING_CFG_ENABLED_PPDU_END_S     3
#define HTT_RX_RING_CFG_ENABLED_MPDU_START_M   0x10
#define HTT_RX_RING_CFG_ENABLED_MPDU_START_S   4
#define HTT_RX_RING_CFG_ENABLED_MPDU_END_M     0x20
#define HTT_RX_RING_CFG_ENABLED_MPDU_END_S     5
#define HTT_RX_RING_CFG_ENABLED_MSDU_START_M   0x40
#define HTT_RX_RING_CFG_ENABLED_MSDU_START_S   6
#define HTT_RX_RING_CFG_ENABLED_MSDU_END_M     0x80
#define HTT_RX_RING_CFG_ENABLED_MSDU_END_S     7
#define HTT_RX_RING_CFG_ENABLED_RX_ATTN_M      0x100
#define HTT_RX_RING_CFG_ENABLED_RX_ATTN_S      8
#define HTT_RX_RING_CFG_ENABLED_FRAG_INFO_M    0x200
#define HTT_RX_RING_CFG_ENABLED_FRAG_INFO_S    9
#define HTT_RX_RING_CFG_ENABLED_UCAST_M        0x400
#define HTT_RX_RING_CFG_ENABLED_UCAST_S        10
#define HTT_RX_RING_CFG_ENABLED_MCAST_M        0x800
#define HTT_RX_RING_CFG_ENABLED_MCAST_S        11
#define HTT_RX_RING_CFG_ENABLED_CTRL_M         0x1000
#define HTT_RX_RING_CFG_ENABLED_CTRL_S         12
#define HTT_RX_RING_CFG_ENABLED_MGMT_M         0x2000
#define HTT_RX_RING_CFG_ENABLED_MGMT_S         13
#define HTT_RX_RING_CFG_ENABLED_NULL_M         0x4000
#define HTT_RX_RING_CFG_ENABLED_NULL_S         14
#define HTT_RX_RING_CFG_ENABLED_PHY_M          0x8000
#define HTT_RX_RING_CFG_ENABLED_PHY_S          15
#define HTT_RX_RING_CFG_IDX_INIT_VAL_M         0xffff0000
#define HTT_RX_RING_CFG_IDX_INIT_VAL_S         16
#define HTT_RX_RING_CFG_OFFSET_802_11_HDR_M    0xffff
#define HTT_RX_RING_CFG_OFFSET_802_11_HDR_S    0
#define HTT_RX_RING_CFG_OFFSET_MSDU_PAYLD_M    0xffff0000
#define HTT_RX_RING_CFG_OFFSET_MSDU_PAYLD_S    16
#define HTT_RX_RING_CFG_OFFSET_PPDU_START_M    0xffff
#define HTT_RX_RING_CFG_OFFSET_PPDU_START_S    0
#define HTT_RX_RING_CFG_OFFSET_PPDU_END_M      0xffff0000
#define HTT_RX_RING_CFG_OFFSET_PPDU_END_S      16
#define HTT_RX_RING_CFG_OFFSET_MPDU_START_M    0xffff
#define HTT_RX_RING_CFG_OFFSET_MPDU_START_S    0
#define HTT_RX_RING_CFG_OFFSET_MPDU_END_M      0xffff0000
#define HTT_RX_RING_CFG_OFFSET_MPDU_END_S      16
#define HTT_RX_RING_CFG_OFFSET_MSDU_START_M    0xffff
#define HTT_RX_RING_CFG_OFFSET_MSDU_START_S    0
#define HTT_RX_RING_CFG_OFFSET_MSDU_END_M      0xffff0000
#define HTT_RX_RING_CFG_OFFSET_MSDU_END_S      16
#define HTT_RX_RING_CFG_OFFSET_RX_ATTN_M       0xffff
#define HTT_RX_RING_CFG_OFFSET_RX_ATTN_S       0
#define HTT_RX_RING_CFG_OFFSET_FRAG_INFO_M     0xffff0000
#define HTT_RX_RING_CFG_OFFSET_FRAG_INFO_S     16

#define HTT_RX_RING_CFG_HDR_BYTES 4
#define HTT_RX_RING_CFG_PAYLD_BYTES_64 44
#define HTT_RX_RING_CFG_PAYLD_BYTES_32 36
#if HTT_PADDR64
    #define HTT_RX_RING_CFG_PAYLD_BYTES HTT_RX_RING_CFG_PAYLD_BYTES_64
#else
    #define HTT_RX_RING_CFG_PAYLD_BYTES HTT_RX_RING_CFG_PAYLD_BYTES_32
#endif
#define HTT_RX_RING_CFG_BYTES(num_rings) \
    (HTT_RX_RING_CFG_HDR_BYTES + (num_rings) * HTT_RX_RING_CFG_PAYLD_BYTES)


#define HTT_RX_RING_CFG_NUM_RINGS_GET(_var) \
    (((_var) & HTT_RX_RING_CFG_NUM_RINGS_M) >> HTT_RX_RING_CFG_NUM_RINGS_S)
#define HTT_RX_RING_CFG_NUM_RINGS_SET(_var, _val)            \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_NUM_RINGS, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_NUM_RINGS_S)); \
    } while (0)

/* degenerate case for 32-bit fields */
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_HI_GET(_var) (_var)
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_HI_SET(_var, _val) \
    ((_var) = (_val))
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_LO_GET(_var) (_var)
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_LO_SET(_var, _val) \
    ((_var) = (_val))
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_GET(_var) (_var)
#define HTT_RX_RING_CFG_IDX_SHADOW_REG_PADDR_SET(_var, _val) \
    ((_var) = (_val))

/* degenerate case for 32-bit fields */
#define HTT_RX_RING_CFG_BASE_PADDR_HI_GET(_var) (_var)
#define HTT_RX_RING_CFG_BASE_PADDR_HI_SET(_var, _val) \
    ((_var) = (_val))
#define HTT_RX_RING_CFG_BASE_PADDR_LO_GET(_var) (_var)
#define HTT_RX_RING_CFG_BASE_PADDR_LO_SET(_var, _val) \
    ((_var) = (_val))
#define HTT_RX_RING_CFG_BASE_PADDR_GET(_var) (_var)
#define HTT_RX_RING_CFG_BASE_PADDR_SET(_var, _val) \
    ((_var) = (_val))

#define HTT_RX_RING_CFG_LEN_GET(_var) \
    (((_var) & HTT_RX_RING_CFG_LEN_M) >> HTT_RX_RING_CFG_LEN_S)
#define HTT_RX_RING_CFG_LEN_SET(_var, _val)            \
    do {                                                    \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_LEN, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_LEN_S)); \
    } while (0)

#define HTT_RX_RING_CFG_BUF_SZ_GET(_var) \
    (((_var) & HTT_RX_RING_CFG_BUF_SZ_M) >> HTT_RX_RING_CFG_BUF_SZ_S)
#define HTT_RX_RING_CFG_BUF_SZ_SET(_var, _val)            \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_BUF_SZ, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_BUF_SZ_S)); \
    } while (0)

#define HTT_RX_RING_CFG_IDX_INIT_VAL_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_IDX_INIT_VAL_M) >> \
    HTT_RX_RING_CFG_IDX_INIT_VAL_S)
#define HTT_RX_RING_CFG_IDX_INIT_VAL_SET(_var, _val)            \
    do {                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_IDX_INIT_VAL, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_IDX_INIT_VAL_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_802_11_HDR_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_802_11_HDR_M) >> \
    HTT_RX_RING_CFG_ENABLED_802_11_HDR_S)
#define HTT_RX_RING_CFG_ENABLED_802_11_HDR_SET(_var, _val)            \
    do {                                                              \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_802_11_HDR, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_802_11_HDR_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_MSDU_PAYLD_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_MSDU_PAYLD_M) >> \
    HTT_RX_RING_CFG_ENABLED_MSDU_PAYLD_S)
#define HTT_RX_RING_CFG_ENABLED_MSDU_PAYLD_SET(_var, _val)            \
    do {                                                              \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_MSDU_PAYLD, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_MSDU_PAYLD_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_PPDU_START_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_PPDU_START_M) >> \
    HTT_RX_RING_CFG_ENABLED_PPDU_START_S)
#define HTT_RX_RING_CFG_ENABLED_PPDU_START_SET(_var, _val)            \
    do {                                                              \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_PPDU_START, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_PPDU_START_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_PPDU_END_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_PPDU_END_M) >> \
    HTT_RX_RING_CFG_ENABLED_PPDU_END_S)
#define HTT_RX_RING_CFG_ENABLED_PPDU_END_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_PPDU_END, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_PPDU_END_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_MPDU_START_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_MPDU_START_M) >> \
    HTT_RX_RING_CFG_ENABLED_MPDU_START_S)
#define HTT_RX_RING_CFG_ENABLED_MPDU_START_SET(_var, _val)            \
    do {                                                              \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_MPDU_START, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_MPDU_START_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_MPDU_END_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_MPDU_END_M) >> \
    HTT_RX_RING_CFG_ENABLED_MPDU_END_S)
#define HTT_RX_RING_CFG_ENABLED_MPDU_END_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_MPDU_END, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_MPDU_END_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_MSDU_START_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_MSDU_START_M) >> \
    HTT_RX_RING_CFG_ENABLED_MSDU_START_S)
#define HTT_RX_RING_CFG_ENABLED_MSDU_START_SET(_var, _val)            \
    do {                                                              \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_MSDU_START, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_MSDU_START_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_MSDU_END_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_MSDU_END_M) >> \
    HTT_RX_RING_CFG_ENABLED_MSDU_END_S)
#define HTT_RX_RING_CFG_ENABLED_MSDU_END_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_MSDU_END, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_MSDU_END_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_RX_ATTN_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_RX_ATTN_M) >> \
    HTT_RX_RING_CFG_ENABLED_RX_ATTN_S)
#define HTT_RX_RING_CFG_ENABLED_RX_ATTN_SET(_var, _val)            \
    do {                                                           \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_RX_ATTN, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_RX_ATTN_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_FRAG_INFO_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_FRAG_INFO_M) >> \
    HTT_RX_RING_CFG_ENABLED_FRAG_INFO_S)
#define HTT_RX_RING_CFG_ENABLED_FRAG_INFO_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_FRAG_INFO, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_FRAG_INFO_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_UCAST_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_UCAST_M) >> \
    HTT_RX_RING_CFG_ENABLED_UCAST_S)
#define HTT_RX_RING_CFG_ENABLED_UCAST_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_UCAST, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_UCAST_S)); \
    } while (0)

#define HTT_RX_RING_CFG_ENABLED_MCAST_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_MCAST_M) >> \
    HTT_RX_RING_CFG_ENABLED_MCAST_S)
#define HTT_RX_RING_CFG_ENABLED_MCAST_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_MCAST, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_MCAST_S)); \
    } while (0)
#define HTT_RX_RING_CFG_ENABLED_CTRL_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_CTRL_M) >> \
    HTT_RX_RING_CFG_ENABLED_CTRL_S)
#define HTT_RX_RING_CFG_ENABLED_CTRL_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_CTRL, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_CTRL_S)); \
    } while (0)
#define HTT_RX_RING_CFG_ENABLED_MGMT_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_MGMT_M) >> \
    HTT_RX_RING_CFG_ENABLED_MGMT_S)
#define HTT_RX_RING_CFG_ENABLED_MGMT_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_MGMT, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_MGMT_S)); \
    } while (0)
#define HTT_RX_RING_CFG_ENABLED_NULL_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_NULL_M) >> \
    HTT_RX_RING_CFG_ENABLED_NULL_S)
#define HTT_RX_RING_CFG_ENABLED_NULL_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_NULL, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_NULL_S)); \
    } while (0)
#define HTT_RX_RING_CFG_ENABLED_PHY_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_ENABLED_PHY_M) >> \
    HTT_RX_RING_CFG_ENABLED_PHY_S)
#define HTT_RX_RING_CFG_ENABLED_PHY_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_ENABLED_PHY, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_ENABLED_PHY_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_802_11_HDR_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_802_11_HDR_M) >> \
    HTT_RX_RING_CFG_OFFSET_802_11_HDR_S)
#define HTT_RX_RING_CFG_OFFSET_802_11_HDR_SET(_var, _val)            \
    do {                                                                  \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_802_11_HDR, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_802_11_HDR_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_MSDU_PAYLD_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_MSDU_PAYLD_M) >> \
    HTT_RX_RING_CFG_OFFSET_MSDU_PAYLD_S)
#define HTT_RX_RING_CFG_OFFSET_MSDU_PAYLD_SET(_var, _val)            \
    do {                                                                  \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_MSDU_PAYLD, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_MSDU_PAYLD_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_PPDU_START_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_PPDU_START_M) >> \
    HTT_RX_RING_CFG_OFFSET_PPDU_START_S)
#define HTT_RX_RING_CFG_OFFSET_PPDU_START_SET(_var, _val)            \
    do {                                                                  \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_PPDU_START, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_PPDU_START_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_PPDU_END_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_PPDU_END_M) >> \
    HTT_RX_RING_CFG_OFFSET_PPDU_END_S)
#define HTT_RX_RING_CFG_OFFSET_PPDU_END_SET(_var, _val)            \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_PPDU_END, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_PPDU_END_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_MPDU_START_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_MPDU_START_M) >> \
    HTT_RX_RING_CFG_OFFSET_MPDU_START_S)
#define HTT_RX_RING_CFG_OFFSET_MPDU_START_SET(_var, _val)            \
    do {                                                                  \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_MPDU_START, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_MPDU_START_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_MPDU_END_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_MPDU_END_M) >> \
    HTT_RX_RING_CFG_OFFSET_MPDU_END_S)
#define HTT_RX_RING_CFG_OFFSET_MPDU_END_SET(_var, _val)            \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_MPDU_END, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_MPDU_END_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_MSDU_START_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_MSDU_START_M) >> \
    HTT_RX_RING_CFG_OFFSET_MSDU_START_S)
#define HTT_RX_RING_CFG_OFFSET_MSDU_START_SET(_var, _val)            \
    do {                                                                  \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_MSDU_START, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_MSDU_START_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_MSDU_END_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_MSDU_END_M) >> \
    HTT_RX_RING_CFG_OFFSET_MSDU_END_S)
#define HTT_RX_RING_CFG_OFFSET_MSDU_END_SET(_var, _val)            \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_MSDU_END, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_MSDU_END_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_RX_ATTN_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_RX_ATTN_M) >> \
    HTT_RX_RING_CFG_OFFSET_RX_ATTN_S)
#define HTT_RX_RING_CFG_OFFSET_RX_ATTN_SET(_var, _val)            \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_RX_ATTN, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_RX_ATTN_S)); \
    } while (0)

#define HTT_RX_RING_CFG_OFFSET_FRAG_INFO_GET(_var)    \
    (((_var) & HTT_RX_RING_CFG_OFFSET_FRAG_INFO_M) >> \
    HTT_RX_RING_CFG_OFFSET_FRAG_INFO_S)
#define HTT_RX_RING_CFG_OFFSET_FRAG_INFO_SET(_var, _val)            \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_RING_CFG_OFFSET_FRAG_INFO, _val);  \
        ((_var) |= ((_val) << HTT_RX_RING_CFG_OFFSET_FRAG_INFO_S)); \
    } while (0)

/**
 * @brief host -> target FW statistics retrieve
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_STATS_REQ
 *
 * @details
 * The following field definitions describe the format of the HTT host
 * to target FW stats retrieve message. The message specifies the type of
 * stats host wants to retrieve.
 *
 * |31          24|23          16|15           8|7            0|
 * |-----------------------------------------------------------|
 * |        stats types request bitmask         |   msg type   |
 * |-----------------------------------------------------------|
 * |         stats types reset bitmask          |   reserved   |
 * |-----------------------------------------------------------|
 * |  stats type  |               config value                 |
 * |-----------------------------------------------------------|
 * |                        cookie LSBs                        |
 * |-----------------------------------------------------------|
 * |                        cookie MSBs                        |
 * |-----------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Purpose: identifies this is a stats upload request message
 *    Value: 0x3 (HTT_H2T_MSG_TYPE_STATS_REQ)
 *  - UPLOAD_TYPES
 *    Bits 31:8
 *    Purpose: identifies which types of FW statistics to upload
 *    Value: mask with bits set in positions defined by htt_dbg_stats_type
 *  - RESET_TYPES
 *    Bits 31:8
 *    Purpose: identifies which types of FW statistics to reset
 *    Value: mask with bits set in positions defined by htt_dbg_stats_type
 *  - CFG_VAL
 *    Bits 23:0
 *    Purpose: give an opaque configuration value to the specified stats type
 *    Value: stats-type specific configuration value
 *        if stats type == tx PPDU log, then CONFIG_VAL has the format:
 *            bits  7:0  - how many per-MPDU byte counts to include in a record
 *            bits 15:8  - how many per-MPDU MSDU counts to include in a record
 *            bits 23:16 - how many per-MSDU byte counts to include in a record
 *  - CFG_STAT_TYPE
 *    Bits 31:24
 *    Purpose: specify which stats type (if any) the config value applies to
 *    Value: htt_dbg_stats_type value, or 0xff if the message doesn't have
 *        a valid configuration specification
 *  - COOKIE_LSBS
 *    Bits 31:0
 *    Purpose: Provide a mechanism to match a target->host stats confirmation
 *        message with its preceding host->target stats request message.
 *    Value: LSBs of the opaque cookie specified by the host-side requestor
 *  - COOKIE_MSBS
 *    Bits 31:0
 *    Purpose: Provide a mechanism to match a target->host stats confirmation
 *        message with its preceding host->target stats request message.
 *    Value: MSBs of the opaque cookie specified by the host-side requestor
 */

#define HTT_H2T_STATS_REQ_MSG_SZ                    20 /* bytes */

#define HTT_H2T_STATS_REQ_CFG_STAT_TYPE_INVALID     0xff

#define HTT_H2T_STATS_REQ_UPLOAD_TYPES_M            0xffffff00
#define HTT_H2T_STATS_REQ_UPLOAD_TYPES_S            8

#define HTT_H2T_STATS_REQ_RESET_TYPES_M             0xffffff00
#define HTT_H2T_STATS_REQ_RESET_TYPES_S             8

#define HTT_H2T_STATS_REQ_CFG_VAL_M                 0x00ffffff
#define HTT_H2T_STATS_REQ_CFG_VAL_S                 0

#define HTT_H2T_STATS_REQ_CFG_STAT_TYPE_M           0xff000000
#define HTT_H2T_STATS_REQ_CFG_STAT_TYPE_S           24

#define HTT_H2T_STATS_REQ_UPLOAD_TYPES_GET(_var)     \
    (((_var) & HTT_H2T_STATS_REQ_UPLOAD_TYPES_M) >>  \
     HTT_H2T_STATS_REQ_UPLOAD_TYPES_S)
#define HTT_H2T_STATS_REQ_UPLOAD_TYPES_SET(_var, _val)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_H2T_STATS_REQ_UPLOAD_TYPES, _val);  \
        ((_var) |= ((_val) << HTT_H2T_STATS_REQ_UPLOAD_TYPES_S)); \
    } while (0)

#define HTT_H2T_STATS_REQ_RESET_TYPES_GET(_var)     \
    (((_var) & HTT_H2T_STATS_REQ_RESET_TYPES_M) >>  \
     HTT_H2T_STATS_REQ_RESET_TYPES_S)
#define HTT_H2T_STATS_REQ_RESET_TYPES_SET(_var, _val)            \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_H2T_STATS_REQ_RESET_TYPES, _val);  \
        ((_var) |= ((_val) << HTT_H2T_STATS_REQ_RESET_TYPES_S)); \
    } while (0)

#define HTT_H2T_STATS_REQ_CFG_VAL_GET(_var)     \
    (((_var) & HTT_H2T_STATS_REQ_CFG_VAL_M) >>  \
     HTT_H2T_STATS_REQ_CFG_VAL_S)
#define HTT_H2T_STATS_REQ_CFG_VAL_SET(_var, _val)            \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_H2T_STATS_REQ_CFG_VAL, _val);  \
        ((_var) |= ((_val) << HTT_H2T_STATS_REQ_CFG_VAL_S)); \
    } while (0)

#define HTT_H2T_STATS_REQ_CFG_STAT_TYPE_GET(_var)     \
    (((_var) & HTT_H2T_STATS_REQ_CFG_STAT_TYPE_M) >>  \
     HTT_H2T_STATS_REQ_CFG_STAT_TYPE_S)
#define HTT_H2T_STATS_REQ_CFG_STAT_TYPE_SET(_var, _val)            \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_H2T_STATS_REQ_CFG_STAT_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_H2T_STATS_REQ_CFG_STAT_TYPE_S)); \
    } while (0)

/**
 * @brief host -> target HTT out-of-band sync request
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_SYNC
 *
 * @details
 *  The HTT SYNC tells the target to suspend processing of subsequent
 *  HTT host-to-target messages until some other target agent locally
 *  informs the target HTT FW that the current sync counter is equal to
 *  or greater than (in a modulo sense) the sync counter specified in
 *  the SYNC message.
 *  This allows other host-target components to synchronize their operation
 *  with HTT, e.g. to ensure that tx frames don't get transmitted until a
 *  security key has been downloaded to and activated by the target.
 *  In the absence of any explicit synchronization counter value
 *  specification, the target HTT FW will use zero as the default current
 *  sync value.
 *
 * |31          24|23          16|15           8|7            0|
 * |-----------------------------------------------------------|
 * |          reserved           |  sync count  |   msg type   |
 * |-----------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Purpose: identifies this as a sync message
 *    Value: 0x4 (HTT_H2T_MSG_TYPE_SYNC)
 *  - SYNC_COUNT
 *    Bits 15:8
 *    Purpose: specifies what sync value the HTT FW will wait for from
 *        an out-of-band specification to resume its operation
 *    Value: in-band sync counter value to compare against the out-of-band
 *        counter spec.
 *        The HTT target FW will suspend its host->target message processing
 *        as long as
 *        0 < (in-band sync counter - out-of-band sync counter) & 0xff < 128
 */

#define HTT_H2T_SYNC_MSG_SZ                 4

#define HTT_H2T_SYNC_COUNT_M                0x0000ff00
#define HTT_H2T_SYNC_COUNT_S                8

#define HTT_H2T_SYNC_COUNT_GET(_var)        \
    (((_var) & HTT_H2T_SYNC_COUNT_M) >>     \
     HTT_H2T_SYNC_COUNT_S)
#define HTT_H2T_SYNC_COUNT_SET(_var, _val)            \
    do {                                              \
        HTT_CHECK_SET_VAL(HTT_H2T_SYNC_COUNT, _val);  \
        ((_var) |= ((_val) << HTT_H2T_SYNC_COUNT_S)); \
    } while (0)


/**
 * @brief host -> target HTT aggregation configuration
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_AGGR_CFG
 */
#define HTT_AGGR_CFG_MSG_SZ                     4

#define HTT_AGGR_CFG_MAX_NUM_AMPDU_SUBFRM_M     0xff00
#define HTT_AGGR_CFG_MAX_NUM_AMPDU_SUBFRM_S     8
#define HTT_AGGR_CFG_MAX_NUM_AMSDU_SUBFRM_M     0x1f0000
#define HTT_AGGR_CFG_MAX_NUM_AMSDU_SUBFRM_S     16

#define HTT_AGGR_CFG_MAX_NUM_AMPDU_SUBFRM_GET(_var) \
    (((_var) & HTT_AGGR_CFG_MAX_NUM_AMPDU_SUBFRM_M) >> \
     HTT_AGGR_CFG_MAX_NUM_AMPDU_SUBFRM_S)
#define HTT_AGGR_CFG_MAX_NUM_AMPDU_SUBFRM_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_AGGR_CFG_MAX_NUM_AMPDU_SUBFRM, _val);  \
        ((_var) |= ((_val) << HTT_AGGR_CFG_MAX_NUM_AMPDU_SUBFRM_S)); \
    } while (0)

#define HTT_AGGR_CFG_MAX_NUM_AMSDU_SUBFRM_GET(_var) \
    (((_var) & HTT_AGGR_CFG_MAX_NUM_AMSDU_SUBFRM_M) >> \
     HTT_AGGR_CFG_MAX_NUM_AMSDU_SUBFRM_S)
#define HTT_AGGR_CFG_MAX_NUM_AMSDU_SUBFRM_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_AGGR_CFG_MAX_NUM_AMSDU_SUBFRM, _val);  \
        ((_var) |= ((_val) << HTT_AGGR_CFG_MAX_NUM_AMSDU_SUBFRM_S)); \
    } while (0)


/**
 * @brief host -> target HTT configure max amsdu info per vdev
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_AGGR_CFG_EX
 *
 * @details
 *  The HTT AGGR CFG EX tells the target to configure max_amsdu info per vdev
 *
 * |31             21|20       16|15           8|7            0|
 * |-----------------------------------------------------------|
 * |       reserved  | vdev id   |   max amsdu  |   msg type   |
 * |-----------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Purpose: identifies this as a aggr cfg ex message
 *    Value: 0xa (HTT_H2T_MSG_TYPE_AGGR_CFG_EX)
 *  - MAX_NUM_AMSDU_SUBFRM
 *    Bits 15:8
 *    Purpose: max MSDUs per A-MSDU
 *  - VDEV_ID
 *    Bits 20:16
 *    Purpose: ID of the vdev to which this limit is applied
 */
#define HTT_AGGR_CFG_EX_MSG_SZ                     4

#define HTT_AGGR_CFG_EX_MAX_NUM_AMSDU_SUBFRM_M     0xff00
#define HTT_AGGR_CFG_EX_MAX_NUM_AMSDU_SUBFRM_S     8
#define HTT_AGGR_CFG_EX_VDEV_ID_M                  0x1f0000
#define HTT_AGGR_CFG_EX_VDEV_ID_S                  16

#define HTT_AGGR_CFG_EX_MAX_NUM_AMSDU_SUBFRM_GET(_var) \
            (((_var) & HTT_AGGR_CFG_EX_MAX_NUM_AMSDU_SUBFRM_M) >> \
             HTT_AGGR_CFG_EX_MAX_NUM_AMSDU_SUBFRM_S)
#define HTT_AGGR_CFG_EX_MAX_NUM_AMSDU_SUBFRM_SET(_var, _val) \
            do {                                                     \
                HTT_CHECK_SET_VAL(HTT_AGGR_CFG_EX_MAX_NUM_AMSDU_SUBFRM, _val);  \
                ((_var) |= ((_val) << HTT_AGGR_CFG_EX_MAX_NUM_AMSDU_SUBFRM_S)); \
            } while (0)

#define HTT_AGGR_CFG_EX_VDEV_ID_GET(_var) \
            (((_var) & HTT_AGGR_CFG_EX_VDEV_ID_M) >> \
             HTT_AGGR_CFG_EX_VDEV_ID_S)
#define HTT_AGGR_CFG_EX_VDEV_ID_SET(_var, _val) \
            do {                                                     \
                HTT_CHECK_SET_VAL(HTT_AGGR_CFG_EX_VDEV_ID, _val);  \
                ((_var) |= ((_val) << HTT_AGGR_CFG_EX_VDEV_ID_S)); \
            } while (0)

/**
 * @brief HTT WDI_IPA Config Message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_WDI_IPA_CFG
 *
 * @details
 *  The HTT WDI_IPA config message is created/sent by host at driver
 *  init time. It contains information about data structures used on
 *  WDI_IPA TX and RX path.
 *  TX CE ring is used for pushing packet metadata from IPA uC
 *  to WLAN FW
 *  TX Completion ring is used for generating TX completions from
 *  WLAN FW to IPA uC
 *  RX Indication ring is used for indicating RX packets from FW
 *  to IPA uC
 *  RX Ring2 is used as either completion ring or as second
 *  indication ring. when Ring2 is used as completion ring, IPA uC
 *  puts completed RX packet meta data to Ring2. when Ring2 is used
 *  as second indication ring, RX packets for LTE-WLAN aggregation are
 *  indicated in Ring2, other RX packets (e.g. hotspot related) are
 *  indicated in RX Indication ring. Please see WDI_IPA specification
 *  for more details.
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |        tx pkt pool size         |      Rsvd      |     msg_type   |
 *     |-------------------------------------------------------------------|
 *     |                 tx comp ring base (bits 31:0)                     |
#if HTT_PADDR64
 *     |                 tx comp ring base (bits 63:32)                    |
#endif
 *     |-------------------------------------------------------------------|
 *     |                         tx comp ring size                         |
 *     |-------------------------------------------------------------------|
 *     |            tx comp WR_IDX physical address (bits 31:0)            |
#if HTT_PADDR64
 *     |            tx comp WR_IDX physical address (bits 63:32)           |
#endif
 *     |-------------------------------------------------------------------|
 *     |            tx CE WR_IDX physical address (bits 31:0)              |
#if HTT_PADDR64
 *     |            tx CE WR_IDX physical address (bits 63:32)             |
#endif
 *     |-------------------------------------------------------------------|
 *     |             rx indication ring base (bits 31:0)                   |
#if HTT_PADDR64
 *     |             rx indication ring base (bits 63:32)                  |
#endif
 *     |-------------------------------------------------------------------|
 *     |                      rx indication ring size                      |
 *     |-------------------------------------------------------------------|
 *     |             rx ind RD_IDX physical address (bits 31:0)            |
#if HTT_PADDR64
 *     |             rx ind RD_IDX physical address (bits 63:32)           |
#endif
 *     |-------------------------------------------------------------------|
 *     |             rx ind WR_IDX physical address (bits 31:0)            |
#if HTT_PADDR64
 *     |             rx ind WR_IDX physical address (bits 63:32)           |
#endif
 *     |-------------------------------------------------------------------|
 *     |-------------------------------------------------------------------|
 *     |                    rx ring2 base (bits 31:0)                      |
#if HTT_PADDR64
 *     |                    rx ring2 base (bits 63:32)                     |
#endif
 *     |-------------------------------------------------------------------|
 *     |                        rx ring2 size                              |
 *     |-------------------------------------------------------------------|
 *     |             rx ring2 RD_IDX physical address (bits 31:0)          |
#if HTT_PADDR64
 *     |             rx ring2 RD_IDX physical address (bits 63:32)         |
#endif
 *     |-------------------------------------------------------------------|
 *     |             rx ring2 WR_IDX physical address (bits 31:0)          |
#if HTT_PADDR64
 *     |             rx ring2 WR_IDX physical address (bits 63:32)         |
#endif
 *     |-------------------------------------------------------------------|
 *
 * Header fields:
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: Identifies this as WDI_IPA config message
 *     value: = 0x8 (HTT_H2T_MSG_TYPE_WDI_IPA_CFG)
 *   - TX_PKT_POOL_SIZE
 *     Bits 15:0
 *     Purpose: Total number of TX packet buffer pool allocated by Host for
 *              WDI_IPA TX path
 *   For systems using 32-bit format for bus addresses:
 *     - TX_COMP_RING_BASE_ADDR
 *       Bits 31:0
 *       Purpose: TX Completion Ring base address in DDR
 *     - TX_COMP_RING_SIZE
 *       Bits 31:0
 *       Purpose: TX Completion Ring size (must be power of 2)
 *     - TX_COMP_WR_IDX_ADDR
 *       Bits 31:0
 *       Purpose: IPA doorbell register address OR DDR address where WIFI FW
 *                updates the Write Index for WDI_IPA TX completion ring
 *     - TX_CE_WR_IDX_ADDR
 *       Bits 31:0
 *       Purpose: DDR address where IPA uC
 *                updates the WR Index for TX CE ring
 *                (needed for fusion platforms)
 *     - RX_IND_RING_BASE_ADDR
 *       Bits 31:0
 *       Purpose: RX Indication Ring base address in DDR
 *     - RX_IND_RING_SIZE
 *       Bits 31:0
 *       Purpose: RX Indication Ring size
 *     - RX_IND_RD_IDX_ADDR
 *       Bits 31:0
 *       Purpose: DDR address where IPA uC updates the Read Index for WDI_IPA
 *                RX indication ring
 *     - RX_IND_WR_IDX_ADDR
 *       Bits 31:0
 *       Purpose: IPA doorbell register address OR DDR address where WIFI FW
 *                updates the Write Index for WDI_IPA RX indication ring
 *     - RX_RING2_BASE_ADDR
 *       Bits 31:0
 *       Purpose: Second RX Ring(Indication or completion)base address in DDR
 *     - RX_RING2_SIZE
 *       Bits 31:0
 *       Purpose: Second RX  Ring size (must be >= RX_IND_RING_SIZE)
 *     - RX_RING2_RD_IDX_ADDR
 *       Bits 31:0
 *       Purpose: If Second RX ring is Indication ring, DDR address where
 *                IPA uC updates the Read Index for Ring2.
 *                If Second RX ring is completion ring, this is NOT used
 *     - RX_RING2_WR_IDX_ADDR
 *       Bits 31:0
 *       Purpose: If Second RX ring is Indication ring,  DDR address where
 *                WIFI FW updates the Write Index for WDI_IPA RX ring2
 *                If second RX ring is completion ring, DDR address where
 *                IPA uC updates the Write Index for Ring 2.
 *   For systems using 64-bit format for bus addresses:
 *     - TX_COMP_RING_BASE_ADDR_LO
 *       Bits 31:0
 *       Purpose: Lower 4 bytes of TX Completion Ring base physical address in DDR
 *     - TX_COMP_RING_BASE_ADDR_HI
 *       Bits 31:0
 *       Purpose: Higher 4 bytes of TX Completion Ring base physical address in DDR
 *     - TX_COMP_RING_SIZE
 *       Bits 31:0
 *       Purpose: TX Completion Ring size (must be power of 2)
 *     - TX_COMP_WR_IDX_ADDR_LO
 *       Bits 31:0
 *       Purpose: Lower 4 bytes of IPA doorbell register address OR
 *                Lower 4 bytes of DDR address where WIFI FW
 *                updates the Write Index for WDI_IPA TX completion ring
 *     - TX_COMP_WR_IDX_ADDR_HI
 *       Bits 31:0
 *       Purpose: Higher 4 bytes of IPA doorbell register address OR
 *                Higher 4 bytes of DDR address where WIFI FW
 *                updates the Write Index for WDI_IPA TX completion ring
 *     - TX_CE_WR_IDX_ADDR_LO
 *       Bits 31:0
 *       Purpose: Lower 4 bytes of DDR address where IPA uC
 *                updates the WR Index for TX CE ring
 *                (needed for fusion platforms)
 *     - TX_CE_WR_IDX_ADDR_HI
 *       Bits 31:0
 *       Purpose: Higher 4 bytes of DDR address where IPA uC
 *                updates the WR Index for TX CE ring
 *                (needed for fusion platforms)
 *     - RX_IND_RING_BASE_ADDR_LO
 *       Bits 31:0
 *       Purpose: Lower 4 bytes of RX Indication Ring base address in DDR
 *     - RX_IND_RING_BASE_ADDR_HI
 *       Bits 31:0
 *       Purpose: Higher 4 bytes of RX Indication Ring base address in DDR
 *     - RX_IND_RING_SIZE
 *       Bits 31:0
 *       Purpose: RX Indication Ring size
 *     - RX_IND_RD_IDX_ADDR_LO
 *       Bits 31:0
 *       Purpose: Lower 4 bytes of DDR address where IPA uC updates the Read Index
 *                for WDI_IPA RX indication ring
 *     - RX_IND_RD_IDX_ADDR_HI
 *       Bits 31:0
 *       Purpose: Higher 4 bytes of DDR address where IPA uC updates the Read Index
 *                for WDI_IPA RX indication ring
 *     - RX_IND_WR_IDX_ADDR_LO
 *       Bits 31:0
 *       Purpose: Lower 4 bytes of IPA doorbell register address OR
 *                Lower 4 bytes of DDR address where WIFI FW
 *                updates the Write Index for WDI_IPA RX indication ring
 *     - RX_IND_WR_IDX_ADDR_HI
 *       Bits 31:0
 *       Purpose: Higher 4 bytes of IPA doorbell register address OR
 *                Higher 4 bytes of DDR address where WIFI FW
 *                updates the Write Index for WDI_IPA RX indication ring
 *     - RX_RING2_BASE_ADDR_LO
 *       Bits 31:0
 *       Purpose: Lower 4 bytes of Second RX Ring(Indication OR completion)base address in DDR
 *     - RX_RING2_BASE_ADDR_HI
 *       Bits 31:0
 *       Purpose: Higher 4 bytes of Second RX Ring(Indication OR completion)base address in DDR
 *     - RX_RING2_SIZE
 *       Bits 31:0
 *       Purpose: Second RX  Ring size (must be >= RX_IND_RING_SIZE)
 *     - RX_RING2_RD_IDX_ADDR_LO
 *       Bits 31:0
 *       Purpose: If Second RX ring is Indication ring, lower 4 bytes of
 *                DDR address where IPA uC updates the Read Index for Ring2.
 *                If Second RX ring is completion ring, this is NOT used
 *     - RX_RING2_RD_IDX_ADDR_HI
 *       Bits 31:0
 *       Purpose: If Second RX ring is Indication ring, higher 4 bytes of
 *                DDR address where IPA uC updates the Read Index for Ring2.
 *                If Second RX ring is completion ring, this is NOT used
 *     - RX_RING2_WR_IDX_ADDR_LO
 *       Bits 31:0
 *       Purpose: If Second RX ring is Indication ring, lower 4 bytes of
 *                DDR address where WIFI FW updates the Write Index
 *                for WDI_IPA RX ring2
 *                If second RX ring is completion ring, lower 4 bytes of
 *                DDR address where IPA uC updates the Write Index for Ring 2.
 *     - RX_RING2_WR_IDX_ADDR_HI
 *       Bits 31:0
 *       Purpose: If Second RX ring is Indication ring, higher 4 bytes of
 *                DDR address where WIFI FW updates the Write Index
 *                for WDI_IPA RX ring2
 *                If second RX ring is completion ring, higher 4 bytes of
 *                DDR address where IPA uC updates the Write Index for Ring 2.
 */

#if HTT_PADDR64
#define HTT_WDI_IPA_CFG_SZ                           88 /* bytes */
#else
#define HTT_WDI_IPA_CFG_SZ                           52 /* bytes */
#endif

#define HTT_WDI_IPA_CFG_TX_PKT_POOL_SIZE_M           0xffff0000
#define HTT_WDI_IPA_CFG_TX_PKT_POOL_SIZE_S           16

#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_M     0xffffffff
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_S     0

#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_LO_M  0xffffffff
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_LO_S  0

#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_HI_M  0xffffffff
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_HI_S  0

#define HTT_WDI_IPA_CFG_TX_COMP_RING_SIZE_M          0xffffffff
#define HTT_WDI_IPA_CFG_TX_COMP_RING_SIZE_S          0

#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_M        0xffffffff
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_S        0

#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_LO_M     0xffffffff
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_LO_S     0

#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_HI_M     0xffffffff
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_HI_S     0

#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_M          0xffffffff
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_S          0

#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_LO_M       0xffffffff
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_LO_S       0

#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_HI_M       0xffffffff
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_HI_S       0

#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_M      0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_S      0

#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_LO_M   0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_LO_S   0

#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_HI_M   0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_HI_S   0

#define HTT_WDI_IPA_CFG_RX_IND_RING_SIZE_M           0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_RING_SIZE_S           0

#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_M         0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_S         0

#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_LO_M      0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_LO_S      0

#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_HI_M      0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_HI_S      0

#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_M         0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_S         0

#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_LO_M      0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_LO_S      0

#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_HI_M      0xffffffff
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_HI_S      0

#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_M         0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_S         0

#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_LO_M      0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_LO_S      0

#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_HI_M      0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_HI_S      0

#define HTT_WDI_IPA_CFG_RX_RING2_SIZE_M              0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_SIZE_S              0

#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_M       0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_S       0

#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_LO_M    0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_LO_S    0

#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_HI_M    0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_HI_S    0

#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_M       0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_S       0

#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_LO_M    0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_LO_S    0

#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_HI_M    0xffffffff
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_HI_S    0

#define HTT_WDI_IPA_CFG_TX_PKT_POOL_SIZE_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_PKT_POOL_SIZE_M) >> HTT_WDI_IPA_CFG_TX_PKT_POOL_SIZE_S)
#define HTT_WDI_IPA_CFG_TX_PKT_POOL_SIZE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_PKT_POOL_SIZE, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_PKT_POOL_SIZE_S)); \
    } while (0)

/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_M) >> HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_S)
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_HI_M) >> HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_LO_M) >> HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_COMP_RING_BASE_ADDR_LO_S)); \
    } while (0)

#define HTT_WDI_IPA_CFG_TX_COMP_RING_SIZE_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_COMP_RING_SIZE_M) >> HTT_WDI_IPA_CFG_TX_COMP_RING_SIZE_S)
#define HTT_WDI_IPA_CFG_TX_COMP_RING_SIZE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_COMP_RING_SIZE, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_COMP_RING_SIZE_S)); \
    } while (0)

/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_M) >> HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_S)
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_HI_M) >> HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_LO_M) >> HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_COMP_WR_IDX_ADDR_LO_S)); \
    } while (0)


/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_M) >> HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_S)
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_HI_M) >> HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_LO_M) >> HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_TX_CE_WR_IDX_ADDR_LO_S)); \
    } while (0)

/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_M) >> HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_S)
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_HI_M) >> HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_LO_M) >> HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_RING_BASE_ADDR_LO_S)); \
    } while (0)

#define HTT_WDI_IPA_CFG_RX_IND_RING_SIZE_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_RING_SIZE_M) >> HTT_WDI_IPA_CFG_RX_IND_RING_SIZE_S)
#define HTT_WDI_IPA_CFG_RX_IND_RING_SIZE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_RING_SIZE, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_RING_SIZE_S)); \
    } while (0)

/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_M) >> HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_S)
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_HI_M) >> HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_LO_M) >> HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_RD_IDX_ADDR_LO_S)); \
    } while (0)

/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_M) >> HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_S)
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_HI_M) >> HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_LO_M) >> HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_IND_WR_IDX_ADDR_LO_S)); \
    } while (0)

/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_M) >> HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_S)
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_HI_M) >> HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_LO_M) >> HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_BASE_ADDR_LO_S)); \
    } while (0)

#define HTT_WDI_IPA_CFG_RX_RING2_SIZE_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_SIZE_M) >> HTT_WDI_IPA_CFG_RX_RING2_SIZE_S)
#define HTT_WDI_IPA_CFG_RX_RING2_SIZE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_SIZE, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_SIZE_S)); \
    } while (0)

/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_M) >> HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_S)
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_HI_M) >> HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_LO_M) >> HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_RD_IDX_ADDR_LO_S)); \
    } while (0)

/* for systems using 32-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_M) >> HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_S)
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_HI_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_HI_M) >> HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_HI_S)
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_HI_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_HI, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_HI_S)); \
    } while (0)

/* for systems using 64-bit format for bus addr */
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_LO_GET(_var) \
    (((_var) & HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_LO_M) >> HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_LO_S)
#define HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_LO_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_LO, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_CFG_RX_RING2_WR_IDX_ADDR_LO_S)); \
    } while (0)

/*
 * TEMPLATE_HTT_WDI_IPA_CONFIG_T:
 * This macro defines a htt_wdi_ipa_configXXX_t in which any physical
 * addresses are stored in a XXX-bit field.
 * This macro is used to define both htt_wdi_ipa_config32_t and
 * htt_wdi_ipa_config64_t structs.
 */
#define TEMPLATE_HTT_WDI_IPA_CONFIG_T(_paddr_bits_, \
                                      _paddr__tx_comp_ring_base_addr_, \
                                      _paddr__tx_comp_wr_idx_addr_, \
                                      _paddr__tx_ce_wr_idx_addr_, \
                                      _paddr__rx_ind_ring_base_addr_, \
                                      _paddr__rx_ind_rd_idx_addr_, \
                                      _paddr__rx_ind_wr_idx_addr_, \
                                      _paddr__rx_ring2_base_addr_,\
                                      _paddr__rx_ring2_rd_idx_addr_,\
                                      _paddr__rx_ring2_wr_idx_addr_)      \
PREPACK struct htt_wdi_ipa_cfg ## _paddr_bits_ ## _t \
{ \
  /* DWORD 0: flags and meta-data */ \
    A_UINT32 \
        msg_type: 8, /* HTT_H2T_MSG_TYPE_WDI_IPA_CFG */ \
        reserved: 8, \
        tx_pkt_pool_size: 16;\
    /* DWORD 1  */\
    _paddr__tx_comp_ring_base_addr_;\
    /* DWORD 2 (or 3)*/\
    A_UINT32 tx_comp_ring_size;\
    /* DWORD 3 (or 4)*/\
    _paddr__tx_comp_wr_idx_addr_;\
    /* DWORD 4 (or 6)*/\
    _paddr__tx_ce_wr_idx_addr_;\
    /* DWORD 5 (or 8)*/\
    _paddr__rx_ind_ring_base_addr_;\
    /* DWORD 6 (or 10)*/\
    A_UINT32 rx_ind_ring_size;\
    /* DWORD 7 (or 11)*/\
    _paddr__rx_ind_rd_idx_addr_;\
    /* DWORD 8 (or 13)*/\
    _paddr__rx_ind_wr_idx_addr_;\
    /* DWORD 9 (or 15)*/\
    _paddr__rx_ring2_base_addr_;\
    /* DWORD 10 (or 17) */\
    A_UINT32 rx_ring2_size;\
    /* DWORD 11 (or 18) */\
    _paddr__rx_ring2_rd_idx_addr_;\
    /* DWORD 12 (or 20) */\
    _paddr__rx_ring2_wr_idx_addr_;\
} POSTPACK

/* define a htt_wdi_ipa_config32_t type */
TEMPLATE_HTT_WDI_IPA_CONFIG_T(32, HTT_VAR_PADDR32(tx_comp_ring_base_addr), HTT_VAR_PADDR32(tx_comp_wr_idx_addr), HTT_VAR_PADDR32(tx_ce_wr_idx_addr), HTT_VAR_PADDR32(rx_ind_ring_base_addr), HTT_VAR_PADDR32(rx_ind_rd_idx_addr),HTT_VAR_PADDR32(rx_ind_wr_idx_addr), HTT_VAR_PADDR32(rx_ring2_base_addr), HTT_VAR_PADDR32(rx_ring2_rd_idx_addr), HTT_VAR_PADDR32(rx_ring2_wr_idx_addr));

/* define a htt_wdi_ipa_config64_t type */
TEMPLATE_HTT_WDI_IPA_CONFIG_T(64, HTT_VAR_PADDR64_LE(tx_comp_ring_base_addr), HTT_VAR_PADDR64_LE(tx_comp_wr_idx_addr), HTT_VAR_PADDR64_LE(tx_ce_wr_idx_addr), HTT_VAR_PADDR64_LE(rx_ind_ring_base_addr), HTT_VAR_PADDR64_LE(rx_ind_rd_idx_addr), HTT_VAR_PADDR64_LE(rx_ind_wr_idx_addr), HTT_VAR_PADDR64_LE(rx_ring2_base_addr), HTT_VAR_PADDR64_LE(rx_ring2_rd_idx_addr), HTT_VAR_PADDR64_LE(rx_ring2_wr_idx_addr));

#if HTT_PADDR64
    #define htt_wdi_ipa_cfg_t htt_wdi_ipa_cfg64_t
#else
    #define htt_wdi_ipa_cfg_t htt_wdi_ipa_cfg32_t
#endif

enum htt_wdi_ipa_op_code {
    HTT_WDI_IPA_OPCODE_TX_SUSPEND           = 0,
    HTT_WDI_IPA_OPCODE_TX_RESUME            = 1,
    HTT_WDI_IPA_OPCODE_RX_SUSPEND           = 2,
    HTT_WDI_IPA_OPCODE_RX_RESUME            = 3,
    HTT_WDI_IPA_OPCODE_DBG_STATS            = 4,
    HTT_WDI_IPA_OPCODE_GET_SHARING_STATS    = 5,
    HTT_WDI_IPA_OPCODE_SET_QUOTA            = 6,
    HTT_WDI_IPA_OPCODE_IND_QUOTA            = 7,
    /* keep this last */
    HTT_WDI_IPA_OPCODE_MAX
};

/**
 * @brief HTT WDI_IPA Operation Request Message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_WDI_IPA_OP_REQ
 *
 * @details
 *  HTT WDI_IPA Operation Request message is sent by host
 *  to either suspend or resume WDI_IPA TX or RX path.
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |             op_code             |      Rsvd      |     msg_type   |
 *     |-------------------------------------------------------------------|
 *
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: Identifies this as WDI_IPA Operation Request message
 *     value: = 0x9 (HTT_H2T_MSG_TYPE_WDI_IPA_OP_REQ)
 *   - OP_CODE
 *     Bits 31:16
 *     Purpose: Identifies operation host is requesting (e.g. TX suspend)
 *     value: = enum htt_wdi_ipa_op_code
 */

PREPACK struct htt_wdi_ipa_op_request_t
{
    /* DWORD 0: flags and meta-data */
    A_UINT32
        msg_type: 8, /* HTT_H2T_MSG_TYPE_WDI_IPA_OP_REQUEST */
        reserved: 8,
        op_code: 16;
} POSTPACK;

#define HTT_WDI_IPA_OP_REQUEST_SZ                    4 /* bytes */

#define HTT_WDI_IPA_OP_REQUEST_OP_CODE_M             0xffff0000
#define HTT_WDI_IPA_OP_REQUEST_OP_CODE_S             16

#define HTT_WDI_IPA_OP_REQUEST_OP_CODE_GET(_var) \
    (((_var) & HTT_WDI_IPA_OP_REQUEST_OP_CODE_M) >> HTT_WDI_IPA_OP_REQUEST_OP_CODE_S)
#define HTT_WDI_IPA_OP_REQUEST_OP_CODE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_OP_REQUEST_OP_CODE, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_OP_REQUEST_OP_CODE_S)); \
    } while (0)

/*
 * @brief  host -> target  HTT_SRING_SETUP message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_SRING_SETUP
 *
 * @details
 * After target is booted up, Host can send SRING setup message for
 * each host facing LMAC SRING. Target setups up HW registers based
 * on setup message and confirms back to Host if response_required is set.
 * Host should wait for confirmation message before sending new SRING
 * setup message
 *
 *    The message would appear as follows:
 *    |31            24|23 21|20|19|18 16|15|14           8|7               0|
 *    |--------------- +-----------------+-----------------+-----------------|
 *    |    ring_type   |      ring_id    |    pdev_id      |    msg_type     |
 *    |----------------------------------------------------------------------|
 *    |                          ring_base_addr_lo                           |
 *    |----------------------------------------------------------------------|
 *    |                         ring_base_addr_hi                            |
 *    |----------------------------------------------------------------------|
 *    |ring_misc_cfg_flag|ring_entry_size|            ring_size              |
 *    |----------------------------------------------------------------------|
 *    |                         ring_head_offset32_remote_addr_lo            |
 *    |----------------------------------------------------------------------|
 *    |                         ring_head_offset32_remote_addr_hi            |
 *    |----------------------------------------------------------------------|
 *    |                         ring_tail_offset32_remote_addr_lo            |
 *    |----------------------------------------------------------------------|
 *    |                         ring_tail_offset32_remote_addr_hi            |
 *    |----------------------------------------------------------------------|
 *    |                          ring_msi_addr_lo                            |
 *    |----------------------------------------------------------------------|
 *    |                          ring_msi_addr_hi                            |
 *    |----------------------------------------------------------------------|
 *    |                          ring_msi_data                               |
 *    |----------------------------------------------------------------------|
 *    |         intr_timer_th            |IM|      intr_batch_counter_th     |
 *    |----------------------------------------------------------------------|
 *    |         reserved     |ID|RR| PTCF|        intr_low_threshold         |
 *    |----------------------------------------------------------------------|
 *    |             reserved             |IPA drop thres hi|IPA drop thres lo|
 *    |----------------------------------------------------------------------|
 * Where
 *     IM = sw_intr_mode
 *     RR = response_required
 *     PTCF = prefetch_timer_cfg
 *     IP = IPA drop flag
 *
 * The message is interpreted as follows:
 * dword0  - b'0:7   - msg_type: This will be set to
 *                     0xb (HTT_H2T_MSG_TYPE_SRING_SETUP)
 *           b'8:15  - pdev_id:
 *                     0 (for rings at SOC/UMAC level),
 *                     1/2/3 mac id (for rings at LMAC level)
 *           b'16:23 - ring_id: identify which ring is to setup,
 *                     more details can be got from enum htt_srng_ring_id
 *           b'24:31 - ring_type: identify type of host rings,
 *                     more details can be got from enum htt_srng_ring_type
 * dword1  - b'0:31  - ring_base_addr_lo: Lower 32bits of ring base address
 * dword2  - b'0:31  - ring_base_addr_hi: Upper 32bits of ring base address
 * dword3  - b'0:15  - ring_size: size of the ring in unit of 4-bytes words
 *           b'16:23 - ring_entry_size: Size of each entry in 4-byte word units
 *           b'24:31 - ring_misc_cfg_flag: Valid only for HW_TO_SW_RING and
 *                     SW_TO_HW_RING.
 *                     Refer to HTT_SRING_SETUP_RING_MISC_CFG_RING defs.
 * dword4  - b'0:31  - ring_head_offset32_remote_addr_lo:
 *                     Lower 32 bits of memory address of the remote variable
 *                     storing the 4-byte word offset that identifies the head
 *                     element within the ring.
 *                     (The head offset variable has type A_UINT32.)
 *                     Valid for HW_TO_SW and SW_TO_SW rings.
 * dword5  - b'0:31  - ring_head_offset32_remote_addr_hi:
 *                     Upper 32 bits of memory address of the remote variable
 *                     storing the 4-byte word offset that identifies the head
 *                     element within the ring.
 *                     (The head offset variable has type A_UINT32.)
 *                     Valid for HW_TO_SW and SW_TO_SW rings.
 * dword6  - b'0:31  - ring_tail_offset32_remote_addr_lo:
 *                     Lower 32 bits of memory address of the remote variable
 *                     storing the 4-byte word offset that identifies the tail
 *                     element within the ring.
 *                     (The tail offset variable has type A_UINT32.)
 *                     Valid for HW_TO_SW and SW_TO_SW rings.
 * dword7  - b'0:31  - ring_tail_offset32_remote_addr_hi:
 *                     Upper 32 bits of memory address of the remote variable
 *                     storing the 4-byte word offset that identifies the tail
 *                     element within the ring.
 *                     (The tail offset variable has type A_UINT32.)
 *                     Valid for HW_TO_SW and SW_TO_SW rings.
 * dword8  - b'0:31  - ring_msi_addr_lo: Lower 32bits of MSI cfg address
 *                     valid only for HW_TO_SW_RING and SW_TO_HW_RING
 * dword9  - b'0:31  - ring_msi_addr_hi: Upper 32bits of MSI cfg address
 *                     valid only for HW_TO_SW_RING and SW_TO_HW_RING
 * dword10 - b'0:31  - ring_msi_data: MSI data
 *                     Refer to HTT_SRING_SETUP_RING_MSC_CFG_xxx defs
 *                     valid only for HW_TO_SW_RING and SW_TO_HW_RING
 * dword11 - b'0:14  - intr_batch_counter_th:
 *                     batch counter threshold is in units of 4-byte words.
 *                     HW internally maintains and increments batch count.
 *                     (see SRING spec for detail description).
 *                     When batch count reaches threshold value, an interrupt
 *                     is generated by HW.
 *           b'15    - sw_intr_mode:
 *                     This configuration shall be static.
 *                     Only programmed at power up.
 *                     0: generate pulse style sw interrupts
 *                     1: generate level style sw interrupts
 *           b'16:31 - intr_timer_th:
 *                     The timer init value when timer is idle or is
 *                     initialized to start downcounting.
 *                     In 8us units (to cover a range of 0 to 524 ms)
 * dword12 - b'0:15  - intr_low_threshold:
 *                     Used only by Consumer ring to generate ring_sw_int_p.
 *                     Ring entries low threshold water mark, that is used
 *                     in combination with the interrupt timer as well as
 *                     the the clearing of the level interrupt.
 *           b'16:18 - prefetch_timer_cfg:
 *                     Used only by Consumer ring to set timer mode to
 *                     support Application prefetch handling.
 *                     The external tail offset/pointer will be updated
 *                     at following intervals:
 *                     3'b000: (Prefetch feature disabled; used only for debug)
 *                     3'b001: 1 usec
 *                     3'b010: 4 usec
 *                     3'b011: 8 usec (default)
 *                     3'b100: 16 usec
 *                     Others: Reserverd
 *           b'19    - response_required:
 *                     Host needs HTT_T2H_MSG_TYPE_SRING_SETUP_DONE as response
 *           b'20    - ipa_drop_flag:
                       Indicates that host will config ipa drop threshold percentage
 *           b'21:31 - reserved:  reserved for future use
 * dword13 - b'0:7   - ipa drop low threshold percentage:
 *           b'8:15  - ipa drop high threshold percentage:
 *           b'16:31 - Reserved
 */
PREPACK struct htt_sring_setup_t {
    A_UINT32 msg_type:  8,
             pdev_id:   8,
             ring_id:   8,
             ring_type: 8;
    A_UINT32 ring_base_addr_lo;
    A_UINT32 ring_base_addr_hi;
    A_UINT32 ring_size:          16,
             ring_entry_size:     8,
             ring_misc_cfg_flag:  8;
    A_UINT32 ring_head_offset32_remote_addr_lo;
    A_UINT32 ring_head_offset32_remote_addr_hi;
    A_UINT32 ring_tail_offset32_remote_addr_lo;
    A_UINT32 ring_tail_offset32_remote_addr_hi;
    A_UINT32 ring_msi_addr_lo;
    A_UINT32 ring_msi_addr_hi;
    A_UINT32 ring_msi_data;
    A_UINT32 intr_batch_counter_th: 15,
             sw_intr_mode:           1,
             intr_timer_th:         16;
    A_UINT32 intr_low_threshold: 16,
             prefetch_timer_cfg:  3,
             response_required:   1,
             ipa_drop_flag:      1,
             reserved1:          11;
    A_UINT32 ipa_drop_low_threshold:    8,
             ipa_drop_high_threshold:   8,
             reserved:                  16;
} POSTPACK;

enum htt_srng_ring_type {
    HTT_HW_TO_SW_RING = 0,
    HTT_SW_TO_HW_RING,
    HTT_SW_TO_SW_RING,
    /* Insert new ring types above this line */
};

enum htt_srng_ring_id {
    HTT_RXDMA_HOST_BUF_RING = 0,   /* Used by FW to feed remote buffers and update remote packets */
    HTT_RXDMA_MONITOR_STATUS_RING, /* For getting all PPDU/MPDU/MSDU status deescriptors on host for monitor VAP or packet log purposes */
    HTT_RXDMA_MONITOR_BUF_RING,    /* For feeding free host buffers to RxDMA for monitor traffic upload */
    HTT_RXDMA_MONITOR_DESC_RING,   /* For providing free LINK_DESC to RXDMA  for monitor traffic upload */
    HTT_RXDMA_MONITOR_DEST_RING,   /* Per MPDU indication to host for monitor traffic upload */
    HTT_HOST1_TO_FW_RXBUF_RING,    /* (mobile only) used by host to provide remote RX buffers */
    HTT_HOST2_TO_FW_RXBUF_RING,    /* (mobile only) second ring used by host to provide remote RX buffers */
    HTT_RXDMA_NON_MONITOR_DEST_RING, /* Per MDPU indication to host for non-monitor RxDMA traffic upload */
    HTT_RXDMA_HOST_BUF_RING2,      /* Second ring used by FW to feed removed buffers and update removed packets */
    /* Add Other SRING which can't be directly configured by host software above this line */
};

#define HTT_SRING_SETUP_SZ    (sizeof(struct htt_sring_setup_t))

#define HTT_SRING_SETUP_PDEV_ID_M                  0x0000ff00
#define HTT_SRING_SETUP_PDEV_ID_S                  8
#define HTT_SRING_SETUP_PDEV_ID_GET(_var) \
        (((_var) & HTT_SRING_SETUP_PDEV_ID_M) >> \
                HTT_SRING_SETUP_PDEV_ID_S)
#define HTT_SRING_SETUP_PDEV_ID_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_PDEV_ID, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_PDEV_ID_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_ID_M                  0x00ff0000
#define HTT_SRING_SETUP_RING_ID_S                  16
#define HTT_SRING_SETUP_RING_ID_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_ID_M) >> \
                HTT_SRING_SETUP_RING_ID_S)
#define HTT_SRING_SETUP_RING_ID_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_ID, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_ID_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_TYPE_M                0xff000000
#define HTT_SRING_SETUP_RING_TYPE_S                24
#define HTT_SRING_SETUP_RING_TYPE_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_TYPE_M) >> \
                HTT_SRING_SETUP_RING_TYPE_S)
#define HTT_SRING_SETUP_RING_TYPE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_TYPE, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_TYPE_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_BASE_ADDR_LO_M        0xffffffff
#define HTT_SRING_SETUP_RING_BASE_ADDR_LO_S        0
#define HTT_SRING_SETUP_RING_BASE_ADDR_LO_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_BASE_ADDR_LO_M) >> \
                HTT_SRING_SETUP_RING_BASE_ADDR_LO_S)
#define HTT_SRING_SETUP_RING_BASE_ADDR_LO_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_BASE_ADDR_LO, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_BASE_ADDR_LO_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_BASE_ADDR_HI_M        0xffffffff
#define HTT_SRING_SETUP_RING_BASE_ADDR_HI_S        0
#define HTT_SRING_SETUP_RING_BASE_ADDR_HI_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_BASE_ADDR_HI_M) >> \
                HTT_SRING_SETUP_RING_BASE_ADDR_HI_S)
#define HTT_SRING_SETUP_RING_BASE_ADDR_HI_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_BASE_ADDR_HI, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_BASE_ADDR_HI_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_SIZE_M               0x0000ffff
#define HTT_SRING_SETUP_RING_SIZE_S               0
#define HTT_SRING_SETUP_RING_SIZE_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_SIZE_M) >> \
                HTT_SRING_SETUP_RING_SIZE_S)
#define HTT_SRING_SETUP_RING_SIZE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_SIZE, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_SIZE_S)); \
        } while (0)

#define HTT_SRING_SETUP_ENTRY_SIZE_M              0x00ff0000
#define HTT_SRING_SETUP_ENTRY_SIZE_S              16
#define HTT_SRING_SETUP_ENTRY_SIZE_GET(_var)    \
        (((_var) & HTT_SRING_SETUP_ENTRY_SIZE_M) >> \
                HTT_SRING_SETUP_ENTRY_SIZE_S)
#define HTT_SRING_SETUP_ENTRY_SIZE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_ENTRY_SIZE, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_ENTRY_SIZE_S)); \
        } while (0)

#define HTT_SRING_SETUP_MISC_CFG_FLAG_M            0xff000000
#define HTT_SRING_SETUP_MISC_CFG_FLAG_S            24
#define HTT_SRING_SETUP_MISC_CFG_FLAG_GET(_var)    \
        (((_var) & HTT_SRING_SETUP_MISC_CFG_FLAG_M) >> \
                HTT_SRING_SETUP_MISC_CFG_FLAG_S)
#define HTT_SRING_SETUP_MISC_CFG_FLAG_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_MISC_CFG_FLAG, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_MISC_CFG_FLAG_S)); \
        } while (0)

/* This control bit is applicable to only Producer, which updates Ring ID field
* of each descriptor before pushing into the ring.
* 0: updates ring_id(default)
* 1: ring_id updating disabled */
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RING_ID_DISABLE_M         0x01000000
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RING_ID_DISABLE_S         24
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RING_ID_DISABLE_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RING_ID_DISABLE_M) >> \
        HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RING_ID_DISABLE_S)
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RING_ID_DISABLE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RING_ID_DISABLE, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RING_ID_DISABLE_S)); \
        } while (0)

/* This control bit is applicable to only Producer, which updates Loopcnt field
* of each descriptor before pushing into the ring.
* 0: updates Loopcnt(default)
* 1: Loopcnt updating disabled */
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_LOOPCOUNT_DISABLE_M  0x02000000
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_LOOPCOUNT_DISABLE_S  25
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_LOOPCOUNT_DISABLE_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_MISC_CFG_FLAG_LOOPCOUNT_DISABLE_M) >> \
        HTT_SRING_SETUP_RING_MISC_CFG_FLAG_LOOPCOUNT_DISABLE_S)
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_LOOPCOUNT_DISABLE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MISC_CFG_FLAG_LOOPCOUNT_DISABLE, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MISC_CFG_FLAG_LOOPCOUNT_DISABLE_S)); \
        } while (0)

/* Secured access enable/disable bit. SRNG drives value of this register bit
* into security_id port of GXI/AXI. */
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_SECURITY_M           0x04000000
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_SECURITY_S           26
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_SECURITY_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_MISC_CFG_FLAG_SECURITY_M) >> \
        HTT_SRING_SETUP_RING_MISC_CFG_FLAG_SECURITY_S)
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_SECURITY_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MISC_CFG_FLAG_SECURITY, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MISC_CFG_FLAG_SECURITY_S)); \
        } while (0)

/* During MSI write operation, SRNG drives value of this register bit into
* swap bit of GXI/AXI. */
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_MSI_SWAP_M           0x08000000
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_MSI_SWAP_S           27
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_MSI_SWAP_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_MISC_CFG_FLAG_MSI_SWAP_M) >> \
        HTT_SRING_SETUP_RING_MISC_CFG_FLAG_MSI_SWAP_S)
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_MSI_SWAP_SET(_var, _val) \
        do {														 \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MISC_CFG_FLAG_MSI_SWAP, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MISC_CFG_FLAG_MSI_SWAP_S)); \
        } while (0)

/* During Pointer write operation, SRNG drives value of this register bit into
* swap bit of GXI/AXI. */
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_HOST_FW_SWAP_M       0x10000000
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_HOST_FW_SWAP_S       28
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_HOST_FW_SWAP_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_MISC_CFG_FLAG_HOST_FW_SWAP_M) >> \
        HTT_SRING_SETUP_RING_MISC_CFG_FLAG_HOST_FW_SWAP_S)
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_HOST_FW_SWAP_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MISC_CFG_FLAG_HOST_FW_SWAP, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MISC_CFG_FLAG_HOST_FW_SWAP_S)); \
        } while (0)

/* During any data or TLV write operation, SRNG drives value of this register
* bit into swap bit of GXI/AXI. */
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_TLV_SWAP_M           0x20000000
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_TLV_SWAP_S           29
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_TLV_SWAP_GET(_var)    \
        (((_var) & HTT_SRING_SETUP_RING_MISC_CFG_FLAG_TLV_SWAP_M) >> \
        HTT_SRING_SETUP_RING_MISC_CFG_FLAG_TLV_SWAP_S)
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_TLV_SWAP_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MISC_CFG_FLAG_TLV_SWAP, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MISC_CFG_FLAG_TLV_SWAP_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RESERVED1                 0x40000000
#define HTT_SRING_SETUP_RING_MISC_CFG_FLAG_RESERVED2                 0x80000000


#define HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_LO_M  0xffffffff
#define HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_LO_S  0
#define HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_LO_GET(_var) \
        (((_var) & HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_LO_M) >> \
                HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_LO_S)
#define HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_LO_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_LO, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_LO_S)); \
        } while (0)

#define HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_HI_M 0xffffffff
#define HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_HI_S 0
#define HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_HI_GET(_var) \
        (((_var) & HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_HI_M) >> \
                HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_HI_S)
#define HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_HI_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_HI, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_HEAD_OFFSET32_REMOTE_BASE_ADDR_HI_S)); \
        } while (0)

#define HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_LO_M 0xffffffff
#define HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_LO_S 0
#define HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_LO_GET(_var) \
        (((_var) & HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_LO_M) >> \
                HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_LO_S)
#define HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_LO_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_LO, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_LO_S)); \
        } while (0)

#define HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_HI_M 0xffffffff
#define HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_HI_S 0
#define HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_HI_GET(_var) \
        (((_var) & HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_HI_M) >> \
                HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_HI_S)
#define HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_HI_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_HI, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_TAIL_OFFSET32_REMOTE_BASE_ADDR_HI_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_MSI_ADDR_LO_M        0xffffffff
#define HTT_SRING_SETUP_RING_MSI_ADDR_LO_S        0
#define HTT_SRING_SETUP_RING_MSI_ADDR_LO_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_MSI_ADDR_LO_M) >> \
                HTT_SRING_SETUP_RING_MSI_ADDR_LO_S)
#define HTT_SRING_SETUP_RING_MSI_ADDR_LO_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MSI_ADDR_LO, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MSI_ADDR_LO_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_MSI_ADDR_HI_M        0xffffffff
#define HTT_SRING_SETUP_RING_MSI_ADDR_HI_S        0
#define HTT_SRING_SETUP_RING_MSI_ADDR_HI_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_MSI_ADDR_HI_M) >> \
                HTT_SRING_SETUP_RING_MSI_ADDR_HI_S)
#define HTT_SRING_SETUP_RING_MSI_ADDR_HI_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MSI_ADDR_HI, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MSI_ADDR_HI_S)); \
        } while (0)

#define HTT_SRING_SETUP_RING_MSI_DATA_M          0xffffffff
#define HTT_SRING_SETUP_RING_MSI_DATA_S          0
#define HTT_SRING_SETUP_RING_MSI_DATA_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RING_MSI_DATA_M) >> \
                HTT_SRING_SETUP_RING_MSI_DATA_S)
#define HTT_SRING_SETUP_RING_MSI_DATA_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RING_MSI_DATA, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RING_MSI_DATA_S)); \
        } while (0)



#define HTT_SRING_SETUP_INTR_BATCH_COUNTER_TH_M    0x00007fff
#define HTT_SRING_SETUP_INTR_BATCH_COUNTER_TH_S    0
#define HTT_SRING_SETUP_INTR_BATCH_COUNTER_TH_GET(_var) \
        (((_var) & HTT_SRING_SETUP_INTR_BATCH_COUNTER_TH_M) >> \
                HTT_SRING_SETUP_INTR_BATCH_COUNTER_TH_S)
#define HTT_SRING_SETUP_INTR_BATCH_COUNTER_TH_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_INTR_BATCH_COUNTER_TH, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_INTR_BATCH_COUNTER_TH_S)); \
        } while (0)

#define HTT_SRING_SETUP_SW_INTR_MODE_M             0x00008000
#define HTT_SRING_SETUP_SW_INTR_MODE_S             15
#define HTT_SRING_SETUP_SW_INTR_MODE_GET(_var) \
        (((_var) & HTT_SRING_SETUP_SW_INTR_MODE_M) >> \
                HTT_SRING_SETUP_SW_INTR_MODE_S)
#define HTT_SRING_SETUP_SW_INTR_MODE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_SW_INTR_MODE, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_SW_INTR_MODE_S)); \
        } while (0)

#define HTT_SRING_SETUP_INTR_TIMER_TH_M            0xffff0000
#define HTT_SRING_SETUP_INTR_TIMER_TH_S            16
#define HTT_SRING_SETUP_INTR_TIMER_TH_GET(_var) \
        (((_var) & HTT_SRING_SETUP_INTR_TIMER_TH_M) >> \
                HTT_SRING_SETUP_INTR_TIMER_TH_S)
#define HTT_SRING_SETUP_INTR_TIMER_TH_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_INTR_TIMER_TH, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_INTR_TIMER_TH_S)); \
        } while (0)

#define HTT_SRING_SETUP_INTR_LOW_TH_M              0x0000ffff
#define HTT_SRING_SETUP_INTR_LOW_TH_S              0
#define HTT_SRING_SETUP_INTR_LOW_TH_GET(_var) \
        (((_var) & HTT_SRING_SETUP_INTR_LOW_TH_M) >> \
                HTT_SRING_SETUP_INTR_LOW_TH_S)
#define HTT_SRING_SETUP_INTR_LOW_TH_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_INTR_LOW_TH, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_INTR_LOW_TH_S)); \
        } while (0)

#define HTT_SRING_SETUP_PREFETCH_TIMER_CFG_M       0x00070000
#define HTT_SRING_SETUP_PREFETCH_TIMER_CFG_S       16
#define HTT_SRING_SETUP_PREFETCH_TIMER_CFG_GET(_var) \
        (((_var) & HTT_SRING_SETUP_PREFETCH_TIMER_CFG_M) >> \
                HTT_SRING_SETUP_PREFETCH_TIMER_CFG_S)
#define HTT_SRING_SETUP_PREFETCH_TIMER_CFG_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_PREFETCH_TIMER_CFG, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_PREFETCH_TIMER_CFG_S)); \
        } while (0)

#define HTT_SRING_SETUP_RESPONSE_REQUIRED_M        0x00080000
#define HTT_SRING_SETUP_RESPONSE_REQUIRED_S        19
#define HTT_SRING_SETUP_RESPONSE_REQUIRED_GET(_var) \
        (((_var) & HTT_SRING_SETUP_RESPONSE_REQUIRED_M) >> \
                HTT_SRING_SETUP_RESPONSE_REQUIRED_S)
#define HTT_SRING_SETUP_RESPONSE_REQUIRED_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_SRING_SETUP_RESPONSE_REQUIRED, _val); \
            ((_var) |= ((_val) << HTT_SRING_SETUP_RESPONSE_REQUIRED_S)); \
        } while (0)


/**
 * @brief host -> target RX ring selection config message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_RX_RING_SELECTION_CFG
 *
 * @details
 *    HTT_H2T_MSG_TYPE_RX_RING_SELECTION_CFG message is sent by host to
 *    configure RXDMA rings.
 *    The configuration is per ring based and includes both packet subtypes
 *    and PPDU/MPDU TLVs.
 *
 *    The message would appear as follows:
 *
 *    |31 28|27|26|25|24|23            16|15  | 11| 10|9 8|7             0|
 *    |-----+--+--+--+--+----------------+----+---+---+---+---------------|
 *    |rsvd1|DT|OV|PS|SS|     ring_id    |     pdev_id    |    msg_type   |
 *    |-------------------------------------------------------------------|
 *    |              rsvd2               |           ring_buffer_size     |
 *    |-------------------------------------------------------------------|
 *    |                        packet_type_enable_flags_0                 |
 *    |-------------------------------------------------------------------|
 *    |                        packet_type_enable_flags_1                 |
 *    |-------------------------------------------------------------------|
 *    |                        packet_type_enable_flags_2                 |
 *    |-------------------------------------------------------------------|
 *    |                        packet_type_enable_flags_3                 |
 *    |-------------------------------------------------------------------|
 *    |                         tlv_filter_in_flags                       |
 *    |-------------------------------------------------------------------|
 *    |         rx_header_offset         |       rx_packet_offset         |
 *    |-------------------------------------------------------------------|
 *    |       rx_mpdu_start_offset       |      rx_mpdu_end_offset        |
 *    |-------------------------------------------------------------------|
 *    |       rx_msdu_start_offset       |      rx_msdu_end_offset        |
 *    |-------------------------------------------------------------------|
 *    |              rsvd3               |      rx_attention_offset       |
 *    |-------------------------------------------------------------------|
 *    |              rsvd4                    | mo| fp| rx_drop_threshold |
 *    |                                       |ndp|ndp|                   |
 *    |-------------------------------------------------------------------|
 * Where:
 *     PS = pkt_swap
 *     SS = status_swap
 *     OV = rx_offsets_valid
 *     DT = drop_thresh_valid
 * The message is interpreted as follows:
 * dword0 - b'0:7   - msg_type: This will be set to
 *                    0xc (HTT_H2T_MSG_TYPE_RX_RING_SELECTION_CFG)
 *          b'8:15  - pdev_id:
 *                    0 (for rings at SOC/UMAC level),
 *                    1/2/3 mac id (for rings at LMAC level)
 *          b'16:23 - ring_id : Identify the ring to configure.
 *                    More details can be got from enum htt_srng_ring_id
 *          b'24    - status_swap (SS): 1 is to swap status TLV - refer to
 *                    BUF_RING_CFG_0 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 *          b'25    - pkt_swap (PS):  1 is to swap packet TLV - refer to
 *                    BUF_RING_CFG_0 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 *          b'26    - rx_offset_valid (OV): flag to indicate rx offsets
 *                    configuration fields are valid
 *          b'27    - drop_thresh_valid (DT): flag to indicate if the
 *                    rx_drop_threshold field is valid
 *          b'28:31 - rsvd1:  reserved for future use
 * dword1 - b'0:16  - ring_buffer_size: size of bufferes referenced by rx ring,
 *                    in byte units.
 *                    Valid only for HW_TO_SW_RING and SW_TO_HW_RING
 *        - b'16:31 - rsvd2: Reserved for future use
 * dword2 - b'0:31  - packet_type_enable_flags_0:
 *                    Enable MGMT packet from 0b0000 to 0b1001
 *                    bits from low to high: FP, MD, MO - 3 bits
 *                        FP: Filter_Pass
 *                        MD: Monitor_Direct
 *                        MO: Monitor_Other
 *                    10 mgmt subtypes * 3 bits -> 30 bits
 *                    Refer to PKT_TYPE_ENABLE_FLAG0_xxx_MGMT_xxx defs
 * dword3 - b'0:31  - packet_type_enable_flags_1:
 *                    Enable MGMT packet from 0b1010 to 0b1111
 *                    bits from low to high: FP, MD, MO - 3 bits
 *                    Refer to PKT_TYPE_ENABLE_FLAG1_xxx_MGMT_xxx defs
 * dword4 - b'0:31 -  packet_type_enable_flags_2:
 *                    Enable CTRL packet from 0b0000 to 0b1001
 *                    bits from low to high: FP, MD, MO - 3 bits
 *                    Refer to PKT_TYPE_ENABLE_FLAG2_xxx_CTRL_xxx defs
 * dword5 - b'0:31  - packet_type_enable_flags_3:
 *                    Enable CTRL packet from 0b1010 to 0b1111,
 *                    MCAST_DATA, UCAST_DATA, NULL_DATA
 *                    bits from low to high: FP, MD, MO - 3 bits
 *                    Refer to PKT_TYPE_ENABLE_FLAG3_xxx_CTRL_xxx defs
 * dword6 - b'0:31 -  tlv_filter_in_flags:
 *                    Filter in Attention/MPDU/PPDU/Header/User tlvs
 *                    Refer to CFG_TLV_FILTER_IN_FLAG defs
 * dword7 - b'0:15 -  rx_packet_offset: rx_packet_offset in byte units
 *                    Valid only for HW_TO_SW_RING and SW_TO_HW_RING
 *                    A value of 0 will be considered as ignore this config.
 *                    Refer to BUF_RING_CFG_1 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 *        - b'16:31 - rx_header_offset: rx_header_offset in byte units
 *                    Valid only for HW_TO_SW_RING and SW_TO_HW_RING
 *                    A value of 0 will be considered as ignore this config.
 *                    Refer to BUF_RING_CFG_1 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 * dword8 - b'0:15 -  rx_mpdu_end_offset: rx_mpdu_end_offset in byte units
 *                    Valid only for HW_TO_SW_RING and SW_TO_HW_RING
 *                    A value of 0 will be considered as ignore this config.
 *                    Refer to BUF_RING_CFG_2 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 *        - b'16:31 - rx_mpdu_start_offset: rx_mpdu_start_offset in byte units
 *                    Valid only for HW_TO_SW_RING and SW_TO_HW_RING
 *                    A value of 0 will be considered as ignore this config.
 *                    Refer to BUF_RING_CFG_2 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 * dword9 - b'0:15 -  rx_msdu_end_offset: rx_msdu_end_offset in byte units
 *                    Valid only for HW_TO_SW_RING and SW_TO_HW_RING
 *                    A value of 0 will be considered as ignore this config.
 *                    Refer to BUF_RING_CFG_3 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 *        - b'16:31 - rx_msdu_start_offset: rx_msdu_start_offset in byte units
 *                    Valid only for HW_TO_SW_RING and SW_TO_HW_RING
 *                    A value of 0 will be considered as ignore this config.
 *                    Refer to BUF_RING_CFG_3 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 * dword10- b'0:15 - rx_attention_offset: rx_attention_offset in byte units
 *                    Valid only for HW_TO_SW_RING and SW_TO_HW_RING
 *                    A value of 0 will be considered as ignore this config.
 *                    Refer to BUF_RING_CFG_4 defs within HW .h files,
 *                    e.g. wmac_top_reg_seq_hwioreg.h
 *        - b'16:31 - rsvd3 for future use
 * dword11- b'9:0 -   rx_drop_threshold: Threshold configured in monitor mode
 *                    to source rings. Consumer drops packets if the available
 *                    words in the ring falls below the configured threshold
 *                    value.
 *        - b'10    - fp_ndp: Flag to indicate FP NDP status tlv is subscribed
 *                    by host. 1 -> subscribed
 *        - b`11    - mo_ndp: Flag to indicate MO NDP status tlv is subscribed
 *                    by host. 1 -> subscribed
 */
PREPACK struct htt_rx_ring_selection_cfg_t {
    A_UINT32 msg_type:          8,
             pdev_id:           8,
             ring_id:           8,
             status_swap:       1,
             pkt_swap:          1,
             rx_offsets_valid:  1,
             drop_thresh_valid: 1,
             rsvd1:             4;
    A_UINT32 ring_buffer_size: 16,
             rsvd2:            16;
    A_UINT32 packet_type_enable_flags_0;
    A_UINT32 packet_type_enable_flags_1;
    A_UINT32 packet_type_enable_flags_2;
    A_UINT32 packet_type_enable_flags_3;
    A_UINT32 tlv_filter_in_flags;
    A_UINT32 rx_packet_offset:     16,
             rx_header_offset:     16;
    A_UINT32 rx_mpdu_end_offset:   16,
             rx_mpdu_start_offset: 16;
    A_UINT32 rx_msdu_end_offset:   16,
             rx_msdu_start_offset: 16;
    A_UINT32 rx_attn_offset:       16,
             rsvd3:                16;
    A_UINT32 rx_drop_threshold:    10,
             fp_ndp:               1,
             mo_ndp:               1,
             rsvd4:                20;
} POSTPACK;

#define HTT_RX_RING_SELECTION_CFG_SZ    (sizeof(struct htt_rx_ring_selection_cfg_t))

#define HTT_RX_RING_SELECTION_CFG_PDEV_ID_M                    0x0000ff00
#define HTT_RX_RING_SELECTION_CFG_PDEV_ID_S                    8
#define HTT_RX_RING_SELECTION_CFG_PDEV_ID_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_PDEV_ID_M) >> \
                    HTT_RX_RING_SELECTION_CFG_PDEV_ID_S)
#define HTT_RX_RING_SELECTION_CFG_PDEV_ID_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_PDEV_ID, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_PDEV_ID_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RING_ID_M                    0x00ff0000
#define HTT_RX_RING_SELECTION_CFG_RING_ID_S                    16
#define HTT_RX_RING_SELECTION_CFG_RING_ID_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RING_ID_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RING_ID_S)
#define HTT_RX_RING_SELECTION_CFG_RING_ID_SET(_var, _val)            \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RING_ID, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RING_ID_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_STATUS_TLV_SWAP_M            0x01000000
#define HTT_RX_RING_SELECTION_CFG_STATUS_TLV_SWAP_S            24
#define HTT_RX_RING_SELECTION_CFG_STATUS_TLV_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_STATUS_TLV_SWAP_M) >> \
                    HTT_RX_RING_SELECTION_CFG_STATUS_TLV_SWAP_S)
#define HTT_RX_RING_SELECTION_CFG_STATUS_TLV_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_STATUS_TLV_SWAP, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_STATUS_TLV_SWAP_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_PKT_TLV_SWAP_M               0x02000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TLV_SWAP_S               25
#define HTT_RX_RING_SELECTION_CFG_PKT_TLV_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_PKT_TLV_SWAP_M) >> \
                    HTT_RX_RING_SELECTION_CFG_PKT_TLV_SWAP_S)
#define HTT_RX_RING_SELECTION_CFG_PKT_TLV_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_PKT_TLV_SWAP, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_PKT_TLV_SWAP_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_OFFSETS_VALID_M           0x04000000
#define HTT_RX_RING_SELECTION_CFG_RX_OFFSETS_VALID_S           26
#define HTT_RX_RING_SELECTION_CFG_RX_OFFSETS_VALID_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_OFFSETS_VALID_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_OFFSETS_VALID_S)
#define HTT_RX_RING_SELECTION_CFG_RX_OFFSETS_VALID_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_OFFSETS_VALID, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_OFFSETS_VALID_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_DROP_THRESHOLD_VALID_M       0x08000000
#define HTT_RX_RING_SELECTION_CFG_DROP_THRESHOLD_VALID_S       27
#define HTT_RX_RING_SELECTION_CFG_DROP_THRESHOLD_VALID_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_DROP_THRESHOLD_VALID_M) >> \
                    HTT_RX_RING_SELECTION_CFG_DROP_THRESHOLD_VALID_S)
#define HTT_RX_RING_SELECTION_CFG_DROP_THRESHOLD_VALID_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_DROP_THRESHOLD_VALID, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_DROP_THRESHOLD_VALID_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RING_BUFFER_SIZE_M           0x0000ffff
#define HTT_RX_RING_SELECTION_CFG_RING_BUFFER_SIZE_S           0
#define HTT_RX_RING_SELECTION_CFG_RING_BUFFER_SIZE_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RING_BUFFER_SIZE_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RING_BUFFER_SIZE_S)
#define HTT_RX_RING_SELECTION_CFG_RING_BUFFER_SIZE_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RING_BUFFER_SIZE, _val);  \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RING_BUFFER_SIZE_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_0_M     0xffffffff
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_0_S     0
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_0_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_0_M) >> \
                    HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_0_S)
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_0_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_0, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_0_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_1_M     0xffffffff
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_1_S     0
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_1_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_1_M) >> \
                    HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_1_S)
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_1_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_1, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_1_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_2_M     0xffffffff
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_2_S     0
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_2_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_2_M) >> \
                    HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_2_S)
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_2_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_2, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_2_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_3_M     0xffffffff
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_3_S     0
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_3_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_3_M) >> \
                    HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_3_S)
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_3_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_3, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG_3_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_M         0xffffffff
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_S         0
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_M) >> \
                    HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_S)
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_PACKET_OFFSET_M         0x0000ffff
#define HTT_RX_RING_SELECTION_CFG_RX_PACKET_OFFSET_S         0
#define HTT_RX_RING_SELECTION_CFG_RX_PACKET_OFFSET_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_PACKET_OFFSET_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_PACKET_OFFSET_S)
#define HTT_RX_RING_SELECTION_CFG_RX_PACKET_OFFSET_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_PACKET_OFFSET, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_PACKET_OFFSET_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_HEADER_OFFSET_M         0xffff0000
#define HTT_RX_RING_SELECTION_CFG_RX_HEADER_OFFSET_S         16
#define HTT_RX_RING_SELECTION_CFG_RX_HEADER_OFFSET_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_HEADER_OFFSET_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_HEADER_OFFSET_S)
#define HTT_RX_RING_SELECTION_CFG_RX_HEADER_OFFSET_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_HEADER_OFFSET, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_HEADER_OFFSET_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_MPDU_END_OFFSET_M         0x0000ffff
#define HTT_RX_RING_SELECTION_CFG_RX_MPDU_END_OFFSET_S         0
#define HTT_RX_RING_SELECTION_CFG_RX_MPDU_END_OFFSET_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_MPDU_END_OFFSET_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_MPDU_END_OFFSET_S)
#define HTT_RX_RING_SELECTION_CFG_RX_MPDU_END_OFFSET_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_MPDU_END_OFFSET, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_MPDU_END_OFFSET_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_MPDU_START_OFFSET_M         0xffff0000
#define HTT_RX_RING_SELECTION_CFG_RX_MPDU_START_OFFSET_S         16
#define HTT_RX_RING_SELECTION_CFG_RX_MPDU_START_OFFSET_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_MPDU_START_OFFSET_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_MPDU_START_OFFSET_S)
#define HTT_RX_RING_SELECTION_CFG_RX_MPDU_START_OFFSET_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_MPDU_START_OFFSET, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_MPDU_START_OFFSET_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_MSDU_END_OFFSET_M         0x0000ffff
#define HTT_RX_RING_SELECTION_CFG_RX_MSDU_END_OFFSET_S         0
#define HTT_RX_RING_SELECTION_CFG_RX_MSDU_END_OFFSET_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_MSDU_END_OFFSET_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_MSDU_END_OFFSET_S)
#define HTT_RX_RING_SELECTION_CFG_RX_MSDU_END_OFFSET_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_MSDU_END_OFFSET, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_MSDU_END_OFFSET_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_MSDU_START_OFFSET_M         0xffff0000
#define HTT_RX_RING_SELECTION_CFG_RX_MSDU_START_OFFSET_S         16
#define HTT_RX_RING_SELECTION_CFG_RX_MSDU_START_OFFSET_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_MSDU_START_OFFSET_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_MSDU_START_OFFSET_S)
#define HTT_RX_RING_SELECTION_CFG_RX_MSDU_START_OFFSET_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_MSDU_START_OFFSET, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_MSDU_START_OFFSET_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_ATTENTION_OFFSET_M         0x0000ffff
#define HTT_RX_RING_SELECTION_CFG_RX_ATTENTION_OFFSET_S         0
#define HTT_RX_RING_SELECTION_CFG_RX_ATTENTION_OFFSET_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_ATTENTION_OFFSET_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_ATTENTION_OFFSET_S)
#define HTT_RX_RING_SELECTION_CFG_RX_ATTENTION_OFFSET_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_ATTENTION_OFFSET, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_ATTENTION_OFFSET_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_RX_DROP_THRESHOLD_M         0x000003ff
#define HTT_RX_RING_SELECTION_CFG_RX_DROP_THRESHOLD_S         0
#define HTT_RX_RING_SELECTION_CFG_RX_DROP_THRESHOLD_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_RX_DROP_THRESHOLD_M) >> \
                    HTT_RX_RING_SELECTION_CFG_RX_DROP_THRESHOLD_S)
#define HTT_RX_RING_SELECTION_CFG_RX_DROP_THRESHOLD_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_RX_DROP_THRESHOLD, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_RX_DROP_THRESHOLD_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_FP_NDP_M         0x00000400
#define HTT_RX_RING_SELECTION_CFG_FP_NDP_S         10
#define HTT_RX_RING_SELECTION_CFG_FP_NDP_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_FP_NDP_M) >> \
                    HTT_RX_RING_SELECTION_CFG_FP_NDP_S)
#define HTT_RX_RING_SELECTION_CFG_FP_NDP_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_FP_NDP, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_FP_NDP_S)); \
            } while (0)

#define HTT_RX_RING_SELECTION_CFG_MO_NDP_M         0x00000800
#define HTT_RX_RING_SELECTION_CFG_MO_NDP_S         11
#define HTT_RX_RING_SELECTION_CFG_MO_NDP_GET(_var) \
            (((_var) & HTT_RX_RING_SELECTION_CFG_MO_NDP_M) >> \
                    HTT_RX_RING_SELECTION_CFG_MO_NDP_S)
#define HTT_RX_RING_SELECTION_CFG_MO_NDP_SET(_var, _val) \
            do { \
                HTT_CHECK_SET_VAL(HTT_RX_RING_SELECTION_CFG_MO_NDP, _val); \
                ((_var) |= ((_val) << HTT_RX_RING_SELECTION_CFG_MO_NDP_S)); \
            } while (0)


/*
 * Subtype based MGMT frames enable bits.
 * FP: Filter_Pass, MD: Monitor_Direct MO: Monitor_Other
 */
/* association request */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0000_M 0x00000001
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0000_S 0

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0000_M 0x00000002
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0000_S 1

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0000_M 0x00000004
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0000_S 2

/* association response */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0001_M 0x00000008
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0001_S 3

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0001_M 0x00000010
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0001_S 4

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0001_M 0x00000020
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0001_S 5

/* Reassociation request */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0010_M 0x00000040
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0010_S 6

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0010_M 0x00000080
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0010_S 7

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0010_M 0x00000100
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0010_S 8

/* Reassociation response */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0011_M 0x00000200
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0011_S 9

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0011_M 0x00000400
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0011_S 10

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0011_M 0x00000800
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0011_S 11

/* Probe request */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0100_M 0x00001000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0100_S 12

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0100_M 0x00002000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0100_S 13

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0100_M 0x00004000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0100_S 14

/* Probe response  */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0101_M 0x00008000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0101_S 15

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0101_M 0x00010000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0101_S 16

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0101_M 0x00020000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0101_S 17

/* Timing Advertisement */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0110_M 0x00040000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0110_S 18

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0110_M 0x00080000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0110_S 19

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0110_M 0x00100000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0110_S 20

/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0111_M 0x00200000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_0111_S 21

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0111_M 0x00400000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_0111_S 22

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0111_M 0x00800000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_0111_S 23

/* Beacon */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_1000_M 0x01000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_1000_S 24

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_1000_M 0x02000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_1000_S 25

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_1000_M 0x04000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_1000_S 26

/* ATIM */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_1001_M 0x08000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_FP_MGMT_1001_S 27

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_1001_M 0x10000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MD_MGMT_1001_S 28

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_1001_M 0x20000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG0_MO_MGMT_1001_S 29

/* Disassociation */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1010_M 0x00000001
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1010_S 0

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1010_M 0x00000002
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1010_S 1

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1010_M 0x00000004
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1010_S 2

/* Authentication */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1011_M 0x00000008
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1011_S 3

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1011_M 0x00000010
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1011_S 4

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1011_M 0x00000020
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1011_S 5

/* Deauthentication */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1100_M 0x00000040
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1100_S 6

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1100_M 0x00000080
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1100_S 7

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1100_M 0x00000100
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1100_S 8

/* Action */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1101_M 0x00000200
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1101_S 9

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1101_M 0x00000400
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1101_S 10

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1101_M 0x00000800
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1101_S 11

/* Action No Ack */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1110_M 0x00001000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1110_S 12

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1110_M 0x00002000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1110_S 13

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1110_M 0x00004000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1110_S 14

/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1111_M 0x00008000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_FP_MGMT_1111_S 15

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1111_M 0x00010000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MD_MGMT_1111_S 16

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1111_M 0x00020000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG1_MO_MGMT_1111_S 17

/*
 * Subtype based CTRL frames enable bits.
 * FP: Filter_Pass, MD: Monitor_Direct, MO: Monitor_Other
 */
/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0000_M 0x00000001
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0000_S 0

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0000_M 0x00000002
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0000_S 1

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0000_M 0x00000004
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0000_S 2

/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0001_M 0x00000008
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0001_S 3

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0001_M 0x00000010
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0001_S 4

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0001_M 0x00000020
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0001_S 5

/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0010_M 0x00000040
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0010_S 6

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0010_M 0x00000080
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0010_S 7

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0010_M 0x00000100
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0010_S 8

/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0011_M 0x00000200
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0011_S 9

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0011_M 0x00000400
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0011_S 10

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0011_M 0x00000800
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0011_S 11

/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0100_M 0x00001000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0100_S 12

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0100_M 0x00002000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0100_S 13

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0100_M 0x00004000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0100_S 14

/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0101_M 0x00008000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0101_S 15

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0101_M 0x00010000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0101_S 16

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0101_M 0x00020000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0101_S 17

/* Reserved */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0110_M 0x00040000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0110_S 18

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0110_M 0x00080000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0110_S 19

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0110_M 0x00100000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0110_S 20

/* Control Wrapper */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0111_M 0x00200000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_0111_S 21

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0111_M 0x00400000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_0111_S 22

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0111_M 0x00800000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_0111_S 23

/* Block Ack Request */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_1000_M 0x01000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_1000_S 24

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_1000_M 0x02000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_1000_S 25

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_1000_M 0x04000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_1000_S 26

/* Block Ack*/
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_1001_M 0x08000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_FP_CTRL_1001_S 27

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_1001_M 0x10000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MD_CTRL_1001_S 28

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_1001_M 0x20000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG2_MO_CTRL_1001_S 29

/* PS-POLL */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1010_M 0x00000001
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1010_S 0

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1010_M 0x00000002
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1010_S 1

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1010_M 0x00000004
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1010_S 2

/* RTS */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1011_M 0x00000008
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1011_S 3

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1011_M 0x00000010
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1011_S 4

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1011_M 0x00000020
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1011_S 5

/* CTS */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1100_M 0x00000040
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1100_S 6

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1100_M 0x00000080
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1100_S 7

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1100_M 0x00000100
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1100_S 8

/* ACK */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1101_M 0x00000200
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1101_S 9

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1101_M 0x00000400
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1101_S 10

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1101_M 0x00000800
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1101_S 11

/* CF-END */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1110_M 0x00001000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1110_S 12

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1110_M 0x00002000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1110_S 13

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1110_M 0x00004000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1110_S 14

/* CF-END + CF-ACK */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1111_M 0x00008000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_CTRL_1111_S 15

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1111_M 0x00010000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_CTRL_1111_S 16

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1111_M 0x00020000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_CTRL_1111_S 17

/* Multicast data */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_DATA_MCAST_M 0x00040000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_DATA_MCAST_S 18

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_DATA_MCAST_M 0x00080000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_DATA_MCAST_S 19

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_DATA_MCAST_M 0x00100000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_DATA_MCAST_S 20

/* Unicast data */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_DATA_UCAST_M 0x00200000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_DATA_UCAST_S 21

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_DATA_UCAST_M 0x00400000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_DATA_UCAST_S 22

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_DATA_UCAST_M 0x00800000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_DATA_UCAST_S 23

/* NULL data */
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_DATA_NULL_M 0x01000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_FP_DATA_NULL_S 24

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_DATA_NULL_M 0x02000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MD_DATA_NULL_S 25

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_DATA_NULL_M 0x04000000
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_FLAG3_MO_DATA_NULL_S 26

#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_SET(word, httsym, value) \
            do { \
                HTT_CHECK_SET_VAL(httsym, value); \
                (word) |= (value) << httsym##_S; \
            } while (0)
#define HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_GET(word, httsym) \
            (((word) & httsym##_M) >> httsym##_S)

#define htt_rx_ring_pkt_enable_subtype_set( \
    word, flag, mode, type, subtype, val) \
    HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_SET( \
        word, HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_##flag##_##mode##_##type##_##subtype, val)

#define htt_rx_ring_pkt_enable_subtype_get( \
    word, flag, mode, type, subtype) \
    HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_GET( \
        word, HTT_RX_RING_SELECTION_CFG_PKT_TYPE_ENABLE_##flag##_##mode##_##type##_##subtype)

/* Definition to filter in TLVs */
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_MPDU_START_M               0x00000001
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_MPDU_START_S               0

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_MSDU_START_M               0x00000002
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_MSDU_START_S               1

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PACKET_M                   0x00000004
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PACKET_S                   2

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_MSDU_END_M                 0x00000008
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_MSDU_END_S                 3

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_MPDU_END_M                 0x00000010
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_MPDU_END_S                 4

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PACKET_HEADER_M            0x00000020
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PACKET_HEADER_S            5

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_RESERVED_M                 0x00000040
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_RESERVED_S                 6

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_ATTENTION_M                0x00000080
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_ATTENTION_S                7

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_START_M               0x00000100
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_START_S               8

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_END_M                 0x00000200
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_END_S                 9

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_END_USER_STATS_M      0x00000400
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_END_USER_STATS_S      10

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_END_USER_STATS_EXT_M  0x00000800
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_END_USER_STATS_EXT_S  11

#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_END_STATUS_DONE_M     0x00001000
#define HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_PPDU_END_STATUS_DONE_S     12

#define HTT_RX_RING_TLV_ENABLE_SET(word, httsym, enable) \
            do { \
                HTT_CHECK_SET_VAL(httsym, enable); \
                (word) |= (enable) << httsym##_S; \
            } while (0)
#define HTT_RX_RING_TLV_ENABLE_GET(word, httsym) \
            (((word) & httsym##_M) >> httsym##_S)

#define htt_rx_ring_tlv_filter_in_enable_set(word, tlv, enable) \
    HTT_RX_RING_TLV_ENABLE_SET( \
        word, HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_##tlv, enable)

#define htt_rx_ring_tlv_filter_in_enable_get(word, tlv) \
    HTT_RX_RING_TLV_ENABLE_GET( \
        word, HTT_RX_RING_SELECTION_CFG_TLV_FILTER_IN_FLAG_RX_##tlv)

/**
 * @brief host --> target Receive Flow Steering configuration message definition
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_RFS_CONFIG
 *
 * host --> target Receive Flow Steering configuration message definition.
 * Host must send this message before sending HTT_H2T_MSG_TYPE_RX_RING_CFG.
 * The reason for this is we want RFS to be configured and ready before MAC
 * remote ring is enabled via HTT_H2T_MSG_TYPE_RX_RING_CFG.
 *
 *     |31            24|23            16|15           9|8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |                   reserved                     |E|    msg type    |
 *     |-------------------------------------------------------------------|
 *     Where E = RFS enable flag
 *
 * The RFS_CONFIG message consists of a single 4-byte word.
 *
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a RFS config msg
 *     Value: 0xf (HTT_H2T_MSG_TYPE_RFS_CONFIG)
 *   - RFS_CONFIG
 *     Bit 8
 *     Purpose: Tells target whether to enable (1) or disable (0)
 *         flow steering feature when sending rx indication messages to host
 */
#define HTT_H2T_RFS_CONFIG_M      0x100
#define HTT_H2T_RFS_CONFIG_S      8
#define HTT_RX_RFS_CONFIG_GET(_var)    \
    (((_var) & HTT_H2T_RFS_CONFIG_M) >> \
        HTT_H2T_RFS_CONFIG_S)
#define HTT_RX_RFS_CONFIG_SET(_var, _val)            \
    do {                                              \
        HTT_CHECK_SET_VAL(HTT_H2T_RFS_CONFIG, _val);  \
        ((_var) |= ((_val) << HTT_H2T_RFS_CONFIG_S)); \
    } while (0)

#define HTT_RFS_CFG_REQ_BYTES     4


/**
 * @brief host -> target FW extended statistics retrieve
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_EXT_STATS_REQ
 *
 * @details
 * The following field definitions describe the format of the HTT host
 * to target FW extended stats retrieve message.
 * The message specifies the type of stats the host wants to retrieve.
 *
 * |31          24|23          16|15           8|7            0|
 * |-----------------------------------------------------------|
 * |   reserved   | stats type   |   pdev_mask  |   msg type   |
 * |-----------------------------------------------------------|
 * |                   config param [0]                        |
 * |-----------------------------------------------------------|
 * |                   config param [1]                        |
 * |-----------------------------------------------------------|
 * |                   config param [2]                        |
 * |-----------------------------------------------------------|
 * |                   config param [3]                        |
 * |-----------------------------------------------------------|
 * |                         reserved                          |
 * |-----------------------------------------------------------|
 * |                        cookie LSBs                        |
 * |-----------------------------------------------------------|
 * |                        cookie MSBs                        |
 * |-----------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Purpose: identifies this is a extended stats upload request message
 *    Value: 0x10 (HTT_H2T_MSG_TYPE_EXT_STATS_REQ)
 *  - PDEV_MASK
 *    Bits 8:15
 *    Purpose: identifies the mask of PDEVs to retrieve stats from
 *    Value: This is a overloaded field, refer to usage and interpretation of
 *           PDEV in interface document.
 *           Bit   8    :  Reserved for SOC stats
 *           Bit 9 - 15 :  Indicates PDEV_MASK in DBDC
 *                         Indicates MACID_MASK in DBS
 *  - STATS_TYPE
 *    Bits 23:16
 *    Purpose: identifies which FW statistics to upload
 *    Value: Defined by htt_dbg_ext_stats_type (see htt_stats.h)
 *  - Reserved
 *    Bits 31:24
 *  - CONFIG_PARAM [0]
 *    Bits 31:0
 *    Purpose: give an opaque configuration value to the specified stats type
 *    Value: stats-type specific configuration value
 *           Refer to htt_stats.h for interpretation for each stats sub_type
 *  - CONFIG_PARAM [1]
 *    Bits 31:0
 *    Purpose: give an opaque configuration value to the specified stats type
 *    Value: stats-type specific configuration value
 *           Refer to htt_stats.h for interpretation for each stats sub_type
 *  - CONFIG_PARAM [2]
 *    Bits 31:0
 *    Purpose: give an opaque configuration value to the specified stats type
 *    Value: stats-type specific configuration value
 *           Refer to htt_stats.h for interpretation for each stats sub_type
 *  - CONFIG_PARAM [3]
 *    Bits 31:0
 *    Purpose: give an opaque configuration value to the specified stats type
 *    Value: stats-type specific configuration value
 *           Refer to htt_stats.h for interpretation for each stats sub_type
 *  - Reserved [31:0] for future use.
 *  - COOKIE_LSBS
 *    Bits 31:0
 *    Purpose: Provide a mechanism to match a target->host stats confirmation
 *        message with its preceding host->target stats request message.
 *    Value: LSBs of the opaque cookie specified by the host-side requestor
 *  - COOKIE_MSBS
 *    Bits 31:0
 *    Purpose: Provide a mechanism to match a target->host stats confirmation
 *        message with its preceding host->target stats request message.
 *    Value: MSBs of the opaque cookie specified by the host-side requestor
 */

#define HTT_H2T_EXT_STATS_REQ_MSG_SZ                32 /* bytes */

#define HTT_H2T_EXT_STATS_REQ_PDEV_MASK_M           0x0000ff00
#define HTT_H2T_EXT_STATS_REQ_PDEV_MASK_S           8

#define HTT_H2T_EXT_STATS_REQ_STATS_TYPE_M          0x00ff0000
#define HTT_H2T_EXT_STATS_REQ_STATS_TYPE_S          16

#define HTT_H2T_EXT_STATS_REQ_CONFIG_PARAM_M        0xffffffff
#define HTT_H2T_EXT_STATS_REQ_CONFIG_PARAM_S        0

#define HTT_H2T_EXT_STATS_REQ_PDEV_MASK_GET(_var)     \
    (((_var) & HTT_H2T_EXT_STATS_REQ_PDEV_MASK_M) >>  \
     HTT_H2T_EXT_STATS_REQ_PDEV_MASK_S)
#define HTT_H2T_EXT_STATS_REQ_PDEV_MASK_SET(_var, _val)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_H2T_EXT_STATS_REQ_PDEV_MASK, _val);  \
        ((_var) |= ((_val) << HTT_H2T_EXT_STATS_REQ_PDEV_MASK_S)); \
    } while (0)

#define HTT_H2T_EXT_STATS_REQ_STATS_TYPE_GET(_var)     \
    (((_var) & HTT_H2T_EXT_STATS_REQ_STATS_TYPE_M) >>  \
     HTT_H2T_EXT_STATS_REQ_STATS_TYPE_S)
#define HTT_H2T_EXT_STATS_REQ_STATS_TYPE_SET(_var, _val)            \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_H2T_EXT_STATS_REQ_STATS_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_H2T_EXT_STATS_REQ_STATS_TYPE_S)); \
    } while (0)

#define HTT_H2T_EXT_STATS_REQ_CONFIG_PARAM_GET(_var)     \
    (((_var) & HTT_H2T_EXT_STATS_REQ_CONFIG_PARAM_M) >>  \
     HTT_H2T_EXT_STATS_REQ_CONFIG_PARAM_S)
#define HTT_H2T_EXT_STATS_REQ_CONFIG_PARAM_SET(_var, _val)            \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_H2T_EXT_STATS_REQ_CONFIG_PARAM, _val);  \
        ((_var) |= ((_val) << HTT_H2T_EXT_STATS_REQ_CONFIG_PARAM_S)); \
    } while (0)

/**
 * @brief host -> target FW  PPDU_STATS request message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_PPDU_STATS_CFG
 *
 * @details
 * The following field definitions describe the format of the HTT host
 * to target FW for PPDU_STATS_CFG msg.
 * The message allows the host to configure the PPDU_STATS_IND messages
 * produced by the target.
 *
 * |31          24|23          16|15           8|7            0|
 * |-----------------------------------------------------------|
 * |    REQ bit mask             |   pdev_mask  |   msg type   |
 * |-----------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Purpose: identifies this is a req to configure ppdu_stats_ind from target
 *    Value: 0x11 (HTT_H2T_MSG_TYPE_PPDU_STATS_CFG)
 *  - PDEV_MASK
 *    Bits 8:15
 *    Purpose: identifies which pdevs this PPDU stats configuration applies to
 *    Value: This is a overloaded field, refer to usage and interpretation of
 *           PDEV in interface document.
 *           Bit   8    :  Reserved for SOC stats
 *           Bit 9 - 15 :  Indicates PDEV_MASK in DBDC
 *                         Indicates MACID_MASK in DBS
 *  - REQ_TLV_BIT_MASK
 *    Bits 16:31
 *    Purpose: each set bit indicates the corresponding PPDU stats TLV type
 *        needs to be included in the target's PPDU_STATS_IND messages.
 *    Value: refer htt_ppdu_stats_tlv_tag_t
 *
 */
#define HTT_H2T_PPDU_STATS_CFG_MSG_SZ                4 /* bytes */

#define HTT_H2T_PPDU_STATS_CFG_PDEV_MASK_M           0x0000ff00
#define HTT_H2T_PPDU_STATS_CFG_PDEV_MASK_S           8

#define HTT_H2T_PPDU_STATS_CFG_TLV_BITMASK_M           0xffff0000
#define HTT_H2T_PPDU_STATS_CFG_TLV_BITMASK_S           16

#define HTT_H2T_PPDU_STATS_CFG_PDEV_MASK_GET(_var)     \
    (((_var) & HTT_H2T_PPDU_STATS_CFG_PDEV_MASK_M) >>  \
     HTT_H2T_PPDU_STATS_CFG_PDEV_MASK_S)

#define HTT_H2T_PPDU_STATS_CFG_PDEV_MASK_SET(_var, _val)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_H2T_PPDU_STATS_CFG_PDEV_MASK, _val);  \
        ((_var) |= ((_val) << HTT_H2T_PPDU_STATS_CFG_PDEV_MASK_S)); \
    } while (0)

#define HTT_H2T_PPDU_STATS_CFG_TLV_BITMASK_GET(_var)     \
    (((_var) & HTT_H2T_PPDU_STATS_CFG_TLV_BITMASK_M) >>  \
     HTT_H2T_PPDU_STATS_CFG_TLV_BITMASK_S)

#define HTT_H2T_PPDU_STATS_CFG_TLV_BITMASK_SET(_var, _val)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_H2T_PPDU_STATS_CFG_TLV_BITMASK, _val);  \
        ((_var) |= ((_val) << HTT_H2T_PPDU_STATS_CFG_TLV_BITMASK_S)); \
    } while (0)

/**
 * @brief Host-->target HTT RX FSE setup message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_RX_FSE_SETUP_CFG
 *
 * @details
 * Through this message, the host will provide details of the flow tables
 * in host DDR along with hash keys.
 * This message can be sent per SOC or per PDEV, which is differentiated
 * by pdev id values.
 * The host will allocate flow search table and sends table size,
 * physical DMA address of flow table, and hash keys to firmware to
 * program into the RXOLE FSE HW block.
 *
 * The following field definitions describe the format of the RX FSE setup
 * message sent from the host to target
 *
 * Header fields:
 *  dword0 - b'7:0   - msg_type: This will be set to
 *                     0x12 (HTT_H2T_MSG_TYPE_RX_FSE_SETUP_CFG)
 *           b'15:8  - pdev_id:  0 indicates msg is for all LMAC rings, i.e. soc
 *                     1, 2, 3 indicates pdev_id 0,1,2 and the msg is for that
 *                     pdev's LMAC ring.
 *           b'31:16 - reserved : Reserved for future use
 *  dword1 - b'19:0  - number of records: This field indicates the number of
 *                     entries in the flow table. For example: 8k number of
 *                     records is equivalent to
 *                         8 * 1024 * sizeof(RX_FLOW_SEARCH_ENTRY_STRUCT)
 *           b'27:20 - max search: This field specifies the skid length to FSE
 *                     parser HW module whenever match is not found at the
 *                     exact index pointed by hash.
 *           b'29:28 - ip_da_sa: This indicates which IPV4-IPV6 RFC to be used.
 *                     Refer htt_ip_da_sa_prefix below for more details.
 *           b'31:30 - reserved: Reserved for future use
 *  dword2 - b'31:0  - base address lo: Lower 4 bytes base address of flow
 *                     table allocated by host in DDR
 *  dword3 - b'31:0  - base address hi: Higher 4 bytes of base address of flow
 *                     table allocated by host in DDR
 *  dword4:13 - b'31:0 - Toeplitz: 315 bits of Toeplitz keys for flow table
 *                     entry hashing
 *
 *
 *       |31 30|29 28|27|26|25    20|19   16|15          8|7            0|
 *       |---------------------------------------------------------------|
 *       |              reserved            |   pdev_id   |  MSG_TYPE    |
 *       |---------------------------------------------------------------|
 *       |resvd|IPDSA|  max_search  |      Number  of  records           |
 *       |---------------------------------------------------------------|
 *       |                       base address lo                         |
 *       |---------------------------------------------------------------|
 *       |                       base address high                       |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 31_0                       |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 63_32                      |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 95_64                      |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 127_96                     |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 159_128                    |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 191_160                    |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 223_192                    |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 255_224                    |
 *       |---------------------------------------------------------------|
 *       |                       toeplitz key 287_256                    |
 *       |---------------------------------------------------------------|
 *       |   reserved   |       toeplitz key 314_288(26:0 bits)          |
 *       |---------------------------------------------------------------|
 * where:
 *     IPDSA = ip_da_sa
 */

/**
 * @brief: htt_ip_da_sa_prefix
 * 0x0 -> Prefix is 0x20010db8_00000000_00000000
 *        IPv6 addresses beginning with 0x20010db8 are reserved for
 *        documentation per RFC3849
 * 0x1 -> Prefix is 0x00000000_00000000_0000ffff RFC4291 IPv4-mapped IPv6
 * 0x2 -> Prefix is 0x0  RFC4291 IPv4-compatible IPv6
 * 0x3 -> Prefix is 0x0064ff9b_00000000_00000000  RFC6052 well-known prefix
 */

enum htt_ip_da_sa_prefix {
        HTT_RX_IPV6_20010db8,
        HTT_RX_IPV4_MAPPED_IPV6,
        HTT_RX_IPV4_COMPATIBLE_IPV6,
        HTT_RX_IPV6_64FF9B,
};


/**
 * @brief Host-->target HTT RX FISA configure and enable
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_RX_FISA_CFG
 *
 * @details
 * The host will send this command down to configure and enable the FISA
 * operational params.
 * Configure RXOLE_RXOLE_R0_FISA_CTRL and RXOLE_RXOLE_R0_FISA_TIMEOUT_THRESH
 * register.
 * Should configure both the MACs.
 *
 * dword0 - b'7:0   - msg_type:
 *                    This will be set to 0x15 (HTT_H2T_MSG_TYPE_RX_FISA_CFG)
 *          b'15:8  - pdev_id:  0 indicates msg is for all LMAC rings, i.e. soc
 *                    1, 2, 3 indicates pdev_id 0,1,2 and the msg is for that
 *                    pdev's LMAC ring.
 *          b'31:16 - reserved : Reserved for future use
 *
 * dword1 - b'0     - enable: Global FISA Enable, 0-FISA Disable, 1-Enable
 *          b'1     - IPSEC_SKIP_SEARCH: Flow search will be skipped for IP_SEC
 *                    packets. 1 flow search will be skipped
 *          b'2     - NON_TCP_SKIP_SEARCH: Flow search will be skipped for Non
 *                    tcp,udp packets
 *          b'3     - ADD_IPV4_FIXED_HDR_LEN: Add IPV4 Fixed HDR to length
 *                    calculation
 *          b'4     - ADD_IPV6_FIXED_HDR_LEN: Add IPV6 Fixed HDR to length
 *                    calculation
 *          b'5     - ADD_TCP_FIXED_HDR_LEN: Add TCP Fixed HDR to length
 *                    calculation
 *          b'6     - ADD_UDP_HDR_LEN: Add UDP HDR to length calculation
 *          b'7     - CHKSUM_CUM_IP_LEN_EN: IPV4 hdr Checksum over cumulative IP
 *                    length
 *                    0  L4 checksum will be provided in the RX_MSDU_END tlv
 *                    1  IPV4 hdr checksum after adjusting for cumulative IP
 *                       length
 *          b'8     - DISABLE_TID_CHECK: 1- Disable TID check for MPDU Sequence
 *                    num jump
 *          b'9     - DISABLE_TA_CHECK: 1- Disable TA check for MPDU Sequence
 *                    num jump
 *          b'10    - DISABLE_QOS_CHECK: 1- Disable checking if qos/nonqos
 *            data type switch has happend for MPDU Sequence num jump
 *          b'11    - DISABLE_RAW_CHECK: 1- Disable checking for raw packet type
 *            for MPDU Sequence num jump
 *          b'12    - DISABLE_DECRYPT_ERR_CHECK: 1- Disable fisa cache commands
 *            for decrypt errors
 *          b'13    - DISABLE_MSDU_DROP_CHECK: 1- Ignore checking of msdu drop
 *            while aggregating a msdu
 *          b'17:14 - LIMIT, Aggregtion limit for number of MSDUs.
 *                    The aggregation is done until (number of MSDUs aggregated
 *                    < LIMIT + 1)
 *          b'31:18 - Reserved
 *
 *          fisa_control_value - 32bit value FW can write to register
 *
 * dword2 - b'31:0  - FISA_TIMEOUT_THRESH, Timeout threshold for aggregation
 *            Threshold value for FISA timeout (units are microseconds).
 *            When the global timestamp exceeds this threshold, FISA
 *            aggregation will be restarted.
 *            A value of 0 means timeout is disabled.
 *            Compare the threshold register with timestamp field in
 *            flow entry to generate timeout for the flow.
 *
 * |31                   18 |17  16|15           8|7            0|
 * |-------------------------------------------------------------|
 * |        reserved               |   pdev_mask  |   msg type   |
 * |-------------------------------------------------------------|
 * |        reserved        |            FISA_CTRL               |
 * |-------------------------------------------------------------|
 * |                    FISA_TIMEOUT_THRESH                      |
 * |-------------------------------------------------------------|
 */
PREPACK struct htt_h2t_msg_type_fisa_config_t {
    A_UINT32 msg_type:8,
             pdev_id:8,
             reserved0:16;

    /**
     * @brief fisa_control - RXOLE_RXOLE_R0_FISA_CTRL  FISA control register
     * [17:0]
     */
     union {
         /*
          * fisa_control_bits structure is deprecated.
          * Please use fisa_control_bits_v2 going forward.
          */
         struct {
             A_UINT32 fisa_enable:                1,
                      ipsec_skip_search:          1,
                      nontcp_skip_search:         1,
                      add_ipv4_fixed_hdr_len:     1,
                      add_ipv6_fixed_hdr_len:     1,
                      add_tcp_fixed_hdr_len:      1,
                      add_udp_hdr_len:            1,
                      chksum_cum_ip_len_en:       1,
                      disable_tid_check:          1,
                      disable_ta_check:           1,
                      disable_qos_check:          1,
                      disable_raw_check:          1,
                      disable_decrypt_err_check:  1,
                      disable_msdu_drop_check:    1,
                      fisa_aggr_limit:            4,
                      reserved:                   14;
         } fisa_control_bits;
         struct {
             A_UINT32 fisa_enable:                1,
                      fisa_aggr_limit:            4,
                      reserved:                   27;
         } fisa_control_bits_v2;

         A_UINT32 fisa_control_value;
    } u_fisa_control;

    /**
     * @brief fisa_timeout_threshold - RXOLE_RXOLE_R0_FISA_TIMEOUT_THRESH FISA
     * timeout threshold for aggregation. Unit in usec.
     * [31:0]
     */
     A_UINT32 fisa_timeout_threshold;
} POSTPACK;


/* DWord 0: pdev-ID */
#define HTT_RX_FISA_CONFIG_PDEV_ID_M                  0x0000ff00
#define HTT_RX_FISA_CONFIG_PDEV_ID_S                  8
#define HTT_RX_FISA_CONFIG_PDEV_ID_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_PDEV_ID_M) >> \
                HTT_RX_FISA_CONFIG_PDEV_ID_S)
#define HTT_RX_FISA_CONFIG_PDEV_ID_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_PDEV_ID, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_PDEV_ID_S)); \
        } while (0)

/* Dword 1: fisa_control_value fisa config */
#define HTT_RX_FISA_CONFIG_FISA_ENABLE_M             0x00000001
#define HTT_RX_FISA_CONFIG_FISA_ENABLE_S             0
#define HTT_RX_FISA_CONFIG_FISA_ENABLE_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_FISA_ENABLE_M) >> \
                HTT_RX_FISA_CONFIG_FISA_ENABLE_S)
#define HTT_RX_FISA_CONFIG_FISA_ENABLE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_FISA_ENABLE, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_FISA_ENABLE_S)); \
        } while (0)

/* Dword 1: fisa_control_value ipsec_skip_search */
#define HTT_RX_FISA_CONFIG_IPSEC_SKIP_SEARCH_M             0x00000002
#define HTT_RX_FISA_CONFIG_IPSEC_SKIP_SEARCH_S             1
#define HTT_RX_FISA_CONFIG_IPSEC_SKIP_SEARCH_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_IPSEC_SKIP_SEARCH_M) >> \
                HTT_RX_FISA_CONFIG_IPSEC_SKIP_SEARCH_S)
#define HTT_RX_FISA_CONFIG_IPSEC_SKIP_SEARCH_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_IPSEC_SKIP_SEARCH, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_IPSEC_SKIP_SEARCH_S)); \
        } while (0)

/* Dword 1: fisa_control_value non_tcp_skip_search */
#define HTT_RX_FISA_CONFIG_NON_TCP_SKIP_SEARCH_M             0x00000004
#define HTT_RX_FISA_CONFIG_NON_TCP_SKIP_SEARCH_S             2
#define HTT_RX_FISA_CONFIG_NON_TCP_SKIP_SEARCH_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_NON_TCP_SKIP_SEARCH_M) >> \
                HTT_RX_FISA_CONFIG_NON_TCP_SKIP_SEARCH_S)
#define HTT_RX_FISA_CONFIG_NON_TCP_SKIP_SEARCH_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_NON_TCP_SKIP_SEARCH, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_NON_TCP_SKIP_SEARCH_S)); \
        } while (0)

/* Dword 1: fisa_control_value add_ipv4_fixed_hdr */
#define HTT_RX_FISA_CONFIG_ADD_IPV4_FIXED_HDR_LEN_M             0x00000008
#define HTT_RX_FISA_CONFIG_ADD_IPV4_FIXED_HDR_LEN_S             3
#define HTT_RX_FISA_CONFIG_ADD_IPV4_FIXED_HDR_LEN_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_ADD_IPV4_FIXED_HDR_LEN_M) >> \
                HTT_RX_FISA_CONFIG_ADD_IPV4_FIXED_HDR_LEN_S)
#define HTT_RX_FISA_CONFIG_ADD_IPV4_FIXED_HDR_LEN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_ADD_IPV4_FIXED_HDR_LEN, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_ADD_IPV4_FIXED_HDR_LEN_S)); \
        } while (0)

/* Dword 1: fisa_control_value add_ipv6_fixed_hdr */
#define HTT_RX_FISA_CONFIG_ADD_IPV6_FIXED_HDR_LEN_M             0x00000010
#define HTT_RX_FISA_CONFIG_ADD_IPV6_FIXED_HDR_LEN_S             4
#define HTT_RX_FISA_CONFIG_ADD_IPV6_FIXED_HDR_LEN_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_ADD_IPV6_FIXED_HDR_LEN_M) >> \
                HTT_RX_FISA_CONFIG_ADD_IPV6_FIXED_HDR_LEN_S)
#define HTT_RX_FISA_CONFIG_ADD_IPV6_FIXED_HDR_LEN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_ADD_IPV6_FIXED_HDR_LEN, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_ADD_IPV6_FIXED_HDR_LEN_S)); \
        } while (0)

/* Dword 1: fisa_control_value tcp_fixed_hdr_len */
#define HTT_RX_FISA_CONFIG_ADD_TCP_FIXED_HDR_LEN_M           0x00000020
#define HTT_RX_FISA_CONFIG_ADD_TCP_FIXED_HDR_LEN_S           5
#define HTT_RX_FISA_CONFIG_ADD_TCP_FIXED_HDR_LEN_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_ADD_TCP_FIXED_HDR_LEN_M) >> \
                HTT_RX_FISA_CONFIG_ADD_TCP_FIXED_HDR_LEN_S)
#define HTT_RX_FISA_CONFIG_ADD_TCP_FIXED_HDR_LEN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_ADD_TCP_FIXED_HDR_LEN, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_ADD_TCP_FIXED_HDR_LEN_S)); \
        } while (0)

/* Dword 1: fisa_control_value add_udp_hdr_len */
#define HTT_RX_FISA_CONFIG_ADD_UDP_HDR_LEN_M             0x00000040
#define HTT_RX_FISA_CONFIG_ADD_UDP_HDR_LEN_S             6
#define HTT_RX_FISA_CONFIG_ADD_UDP_HDR_LEN_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_ADD_UDP_HDR_LEN_M) >> \
                HTT_RX_FISA_CONFIG_ADD_UDP_HDR_LEN_S)
#define HTT_RX_FISA_CONFIG_ADD_UDP_HDR_LEN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_ADD_UDP_HDR_LEN, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_ADD_UDP_HDR_LEN_S)); \
        } while (0)

/* Dword 1: fisa_control_value chksum_cum_ip_len_en */
#define HTT_RX_FISA_CONFIG_CHKSUM_CUM_IP_LEN_EN_M        0x00000080
#define HTT_RX_FISA_CONFIG_CHKSUM_CUM_IP_LEN_EN_S        7
#define HTT_RX_FISA_CONFIG_CHKSUM_CUM_IP_LEN_EN_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_CHKSUM_CUM_IP_LEN_EN_M) >> \
                HTT_RX_FISA_CONFIG_CHKSUM_CUM_IP_LEN_EN_S)
#define HTT_RX_FISA_CONFIG_CHKSUM_CUM_IP_LEN_EN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_CHKSUM_CUM_IP_LEN_EN, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_CHKSUM_CUM_IP_LEN_EN_S)); \
        } while (0)

/* Dword 1: fisa_control_value disable_tid_check */
#define HTT_RX_FISA_CONFIG_DISABLE_TID_CHECK_M        0x00000100
#define HTT_RX_FISA_CONFIG_DISABLE_TID_CHECK_S        8
#define HTT_RX_FISA_CONFIG_DISABLE_TID_CHECK_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_DISABLE_TID_CHECK_M) >> \
                HTT_RX_FISA_CONFIG_DISABLE_TID_CHECK_S)
#define HTT_RX_FISA_CONFIG_DISABLE_TID_CHECK_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_DISABLE_TID_CHECK, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_DISABLE_TID_CHECK_S)); \
        } while (0)

/* Dword 1: fisa_control_value disable_ta_check */
#define HTT_RX_FISA_CONFIG_DISABLE_TA_CHECK_M        0x00000200
#define HTT_RX_FISA_CONFIG_DISABLE_TA_CHECK_S        9
#define HTT_RX_FISA_CONFIG_DISABLE_TA_CHECK_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_DISABLE_TA_CHECK_M) >> \
                HTT_RX_FISA_CONFIG_DISABLE_TA_CHECK_S)
#define HTT_RX_FISA_CONFIG_DISABLE_TA_CHECK_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_DISABLE_TA_CHECK, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_DISABLE_TA_CHECK_S)); \
        } while (0)

/* Dword 1: fisa_control_value disable_qos_check */
#define HTT_RX_FISA_CONFIG_DISABLE_QOS_CHECK_M        0x00000400
#define HTT_RX_FISA_CONFIG_DISABLE_QOS_CHECK_S        10
#define HTT_RX_FISA_CONFIG_DISABLE_QOS_CHECK_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_DISABLE_QOS_CHECK_M) >> \
                HTT_RX_FISA_CONFIG_DISABLE_QOS_CHECK_S)
#define HTT_RX_FISA_CONFIG_DISABLE_QOS_CHECK_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_DISABLE_QOS_CHECK, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_DISABLE_QOS_CHECK_S)); \
        } while (0)

/* Dword 1: fisa_control_value  disable_raw_check */
#define HTT_RX_FISA_CONFIG_DISABLE_RAW_CHECK_M        0x00000800
#define HTT_RX_FISA_CONFIG_DISABLE_RAW_CHECK_S        11
#define HTT_RX_FISA_CONFIG_DISABLE_RAW_CHECK_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_DISABLE_RAW_CHECK_M) >> \
                HTT_RX_FISA_CONFIG_DISABLE_RAW_CHECK_S)
#define HTT_RX_FISA_CONFIG_DISABLE_RAW_CHECK_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_DISABLE_RAW_CHECK, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_DISABLE_RAW_CHECK_S)); \
        } while (0)

/* Dword 1: fisa_control_value disable_decrypt_err_check */
#define HTT_RX_FISA_CONFIG_DISABLE_DECRYPT_ERR_CHECK_M        0x00001000
#define HTT_RX_FISA_CONFIG_DISABLE_DECRYPT_ERR_CHECK_S        12
#define HTT_RX_FISA_CONFIG_DISABLE_DECRYPT_ERR_CHECK_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_DISABLE_DECRYPT_ERR_CHECK_M) >> \
                HTT_RX_FISA_CONFIG_DISABLE_DECRYPT_ERR_CHECK_S)
#define HTT_RX_FISA_CONFIG_DISABLE_DECRYPT_ERR_CHECK_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_DISABLE_DECRYPT_ERR_CHECK, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_DISABLE_DECRYPT_ERR_CHECK_S)); \
        } while (0)

/* Dword 1: fisa_control_value disable_msdu_drop_check */
#define HTT_RX_FISA_CONFIG_DISABLE_MSDU_DROP_CHECK_M        0x00002000
#define HTT_RX_FISA_CONFIG_DISABLE_MSDU_DROP_CHECK_S        13
#define HTT_RX_FISA_CONFIG_DISABLE_MSDU_DROP_CHECK_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_DISABLE_MSDU_DROP_CHECK_M) >> \
                HTT_RX_FISA_CONFIG_DISABLE_MSDU_DROP_CHECK_S)
#define HTT_RX_FISA_CONFIG_DISABLE_MSDU_DROP_CHECK_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_DISABLE_MSDU_DROP_CHECK, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_DISABLE_MSDU_DROP_CHECK_S)); \
        } while (0)

/* Dword 1: fisa_control_value fisa_aggr_limit */
#define HTT_RX_FISA_CONFIG_FISA_AGGR_LIMIT_M        0x0003c000
#define HTT_RX_FISA_CONFIG_FISA_AGGR_LIMIT_S        14
#define HTT_RX_FISA_CONFIG_FISA_AGGR_LIMIT_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_FISA_AGGR_LIMIT_M) >> \
                HTT_RX_FISA_CONFIG_FISA_AGGR_LIMIT_S)
#define HTT_RX_FISA_CONFIG_FISA_AGGR_LIMIT_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_FISA_AGGR_LIMIT, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_FISA_AGGR_LIMIT_S)); \
        } while (0)

/* Dword 1: fisa_control_value fisa config */
#define HTT_RX_FISA_CONFIG_FISA_V2_ENABLE_M             0x00000001
#define HTT_RX_FISA_CONFIG_FISA_V2_ENABLE_S             0
#define HTT_RX_FISA_CONFIG_FISA_V2_ENABLE_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_FISA_V2_ENABLE_M) >> \
                HTT_RX_FISA_CONFIG_FISA_V2_ENABLE_S)
#define HTT_RX_FISA_CONFIG_FISA_V2_ENABLE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_FISA_V2_ENABLE, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_FISA_V2_ENABLE_S)); \
        } while (0)

/* Dword 1: fisa_control_value fisa_aggr_limit */
#define HTT_RX_FISA_CONFIG_FISA_V2_AGGR_LIMIT_M        0x0000001e
#define HTT_RX_FISA_CONFIG_FISA_V2_AGGR_LIMIT_S        1
#define HTT_RX_FISA_CONFIG_FISA_V2_AGGR_LIMIT_GET(_var) \
        (((_var) & HTT_RX_FISA_CONFIG_FISA_V2_AGGR_LIMIT_M) >> \
                HTT_RX_FISA_CONFIG_FISA_V2_AGGR_LIMIT_S)
#define HTT_RX_FISA_CONFIG_FISA_V2_AGGR_LIMIT_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FISA_CONFIG_FISA_V2_AGGR_LIMIT, _val); \
            ((_var) |= ((_val) << HTT_RX_FISA_CONFIG_FISA_V2_AGGR_LIMIT_S)); \
        } while (0)

PREPACK struct htt_h2t_msg_rx_fse_setup_t {
        A_UINT32 msg_type:8,  /* HTT_H2T_MSG_TYPE_RX_FSE_SETUP_CFG */
                 pdev_id:8,
                 reserved0:16;
        A_UINT32 num_records:20,
                 max_search:8,
                 ip_da_sa:2, /* htt_ip_da_sa_prefix enumeration */
                 reserved1:2;
        A_UINT32 base_addr_lo;
        A_UINT32 base_addr_hi;
        A_UINT32 toeplitz31_0;
        A_UINT32 toeplitz63_32;
        A_UINT32 toeplitz95_64;
        A_UINT32 toeplitz127_96;
        A_UINT32 toeplitz159_128;
        A_UINT32 toeplitz191_160;
        A_UINT32 toeplitz223_192;
        A_UINT32 toeplitz255_224;
        A_UINT32 toeplitz287_256;
        A_UINT32 toeplitz314_288:27,
                 reserved2:5;
} POSTPACK;

#define HTT_RX_FSE_SETUP_SZ  (sizeof(struct htt_h2t_msg_rx_fse_setup_t))
#define HTT_RX_FSE_OPERATION_SZ (sizeof(struct htt_h2t_msg_rx_fse_operation_t))
#define HTT_RX_FISA_CONFIG_SZ (sizeof(struct htt_h2t_msg_type_fisa_config_t))

#define HTT_RX_FSE_SETUP_HASH_314_288_M 0x07ffffff
#define HTT_RX_FSE_SETUP_HASH_314_288_S 0

/* DWORD 0: Pdev ID */
#define HTT_RX_FSE_SETUP_PDEV_ID_M                  0x0000ff00
#define HTT_RX_FSE_SETUP_PDEV_ID_S                  8
#define HTT_RX_FSE_SETUP_PDEV_ID_GET(_var) \
        (((_var) & HTT_RX_FSE_SETUP_PDEV_ID_M) >> \
                HTT_RX_FSE_SETUP_PDEV_ID_S)
#define HTT_RX_FSE_SETUP_PDEV_ID_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FSE_SETUP_PDEV_ID, _val); \
            ((_var) |= ((_val) << HTT_RX_FSE_SETUP_PDEV_ID_S)); \
        } while (0)

/* DWORD 1:num of records */
#define HTT_RX_FSE_SETUP_NUM_REC_M                  0x000fffff
#define HTT_RX_FSE_SETUP_NUM_REC_S                  0
#define HTT_RX_FSE_SETUP_NUM_REC_GET(_var) \
        (((_var) & HTT_RX_FSE_SETUP_NUM_REC_M) >> \
            HTT_RX_FSE_SETUP_NUM_REC_S)
#define HTT_RX_FSE_SETUP_NUM_REC_SET(_var, _val) \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_SETUP_NUM_REC, _val); \
           ((_var) |= ((_val) << HTT_RX_FSE_SETUP_NUM_REC_S)); \
      } while (0)

/* DWORD 1:max_search */
#define HTT_RX_FSE_SETUP_MAX_SEARCH_M               0x0ff00000
#define HTT_RX_FSE_SETUP_MAX_SEARCH_S               20
#define HTT_RX_FSE_SETUP_MAX_SEARCH_GET(_var) \
        (((_var) & HTT_RX_FSE_SETUP_MAX_SEARCH_M) >> \
            HTT_RX_FSE_SETUP_MAX_SEARCH_S)
#define HTT_RX_FSE_SETUP_MAX_SEARCH_SET(_var, _val) \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_SETUP_MAX_SEARCH, _val); \
          ((_var) |= ((_val) << HTT_RX_FSE_SETUP_MAX_SEARCH_S)); \
      } while (0)

/* DWORD 1:ip_da_sa prefix */
#define HTT_RX_FSE_SETUP_IP_DA_SA_PREFIX_M               0x30000000
#define HTT_RX_FSE_SETUP_IP_DA_SA_PREFIX_S               28
#define HTT_RX_FSE_SETUP_IP_DA_SA_PREFIX_GET(_var) \
        (((_var) & HTT_RX_FSE_SETUP_IP_DA_SA_PREFIX_M) >> \
            HTT_RX_FSE_SETUP_IP_DA_SA_PREFIX_S)
#define HTT_RX_FSE_SETUP_IP_DA_SA_PREFIX_SET(_var, _val) \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_SETUP_IP_DA_SA_PREFIX, _val); \
          ((_var) |= ((_val) << HTT_RX_FSE_SETUP_IP_DA_SA_PREFIX_S)); \
      } while (0)

/* DWORD 2: Base Address LO */
#define HTT_RX_FSE_SETUP_BASE_ADDR_LO_M        0xffffffff
#define HTT_RX_FSE_SETUP_BASE_ADDR_LO_S        0
#define HTT_RX_FSE_SETUP_BASE_ADDR_LO_GET(_var) \
        (((_var) & HTT_RX_FSE_SETUP_BASE_ADDR_LO_M) >> \
            HTT_RX_FSE_SETUP_BASE_ADDR_LO_S)
#define HTT_RX_FSE_SETUP_BASE_ADDR_LO_SET(_var, _val) \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_SETUP_BASE_ADDR_LO, _val); \
          ((_var) |= ((_val) << HTT_RX_FSE_SETUP_BASE_ADDR_LO_S)); \
      } while (0)

/* DWORD 3: Base Address High */
#define HTT_RX_FSE_SETUP_BASE_ADDR_HI_M        0xffffffff
#define HTT_RX_FSE_SETUP_BASE_ADDR_HI_S        0
#define HTT_RX_FSE_SETUP_BASE_ADDR_HI_GET(_var) \
        (((_var) & HTT_RX_FSE_SETUP_BASE_ADDR_HI_M) >> \
            HTT_RX_FSE_SETUP_BASE_ADDR_HI_S)
#define HTT_RX_FSE_SETUP_BASE_ADDR_HI_SET(_var, _val) \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_SETUP_BASE_ADDR_HI, _val); \
        ((_var) |= ((_val) << HTT_RX_FSE_SETUP_BASE_ADDR_HI_S)); \
      } while (0)

/* DWORD 4-12: Hash Value */
#define HTT_RX_FSE_SETUP_HASH_VALUE_M        0xffffffff
#define HTT_RX_FSE_SETUP_HASH_VALUE_S        0
#define HTT_RX_FSE_SETUP_HASH_VALUE_GET(_var) \
        (((_var) & HTT_RX_FSE_SETUP_HASH_VALUE_M) >> \
            HTT_RX_FSE_SETUP_HASH_VALUE_S)
#define HTT_RX_FSE_SETUP_HASH_VALUE_SET(_var, _val) \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_SETUP_HASH_VALUE, _val); \
          ((_var) |= ((_val) << HTT_RX_FSE_SETUP_HASH_VALUE_S)); \
      } while (0)

/* DWORD 13: Hash Value 314:288 bits */
#define HTT_RX_FSE_SETUP_HASH_314_288_GET(_var) \
    (((_var) & HTT_RX_FSE_SETUP_HASH_314_288_M) >> \
    HTT_RX_FSE_SETUP_HASH_314_288_S)
#define HTT_RX_FSE_SETUP_HASH_314_288_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_FSE_SETUP_HASH_314_288, _val);  \
        ((_var) |= ((_val) << HTT_RX_FSE_SETUP_HASH_314_288_S)); \
    } while (0)

/**
 * @brief Host-->target HTT RX FSE operation message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_RX_FSE_OPERATION_CFG
 *
 * @details
 * The host will send this Flow Search Engine (FSE) operation message for
 * every flow add/delete operation.
 * The FSE operation includes FSE full cache invalidation or individual entry
 * invalidation.
 * This message can be sent per SOC or per PDEV which is differentiated
 * by pdev id values.
 *
 *       |31                            16|15          8|7          1|0|
 *       |-------------------------------------------------------------|
 *       |             reserved           |   pdev_id   |  MSG_TYPE    |
 *       |-------------------------------------------------------------|
 *       |             reserved                         | operation  |I|
 *       |-------------------------------------------------------------|
 *       |                      ip_src_addr_31_0                       |
 *       |-------------------------------------------------------------|
 *       |                      ip_src_addr_63_32                      |
 *       |-------------------------------------------------------------|
 *       |                      ip_src_addr_95_64                      |
 *       |-------------------------------------------------------------|
 *       |                      ip_src_addr_127_96                     |
 *       |-------------------------------------------------------------|
 *       |                      ip_dst_addr_31_0                       |
 *       |-------------------------------------------------------------|
 *       |                      ip_dst_addr_63_32                      |
 *       |-------------------------------------------------------------|
 *       |                      ip_dst_addr_95_64                      |
 *       |-------------------------------------------------------------|
 *       |                      ip_dst_addr_127_96                     |
 *       |-------------------------------------------------------------|
 *       |         l4_dst_port           |       l4_src_port           |
 *       |                (32-bit SPI incase of IPsec)                 |
 *       |-------------------------------------------------------------|
 *       |                   reserved                   |  l4_proto    |
 *       |-------------------------------------------------------------|
 *
 * where I is 1-bit ipsec_valid.
 *
 * The following field definitions describe the format of the RX FSE operation
 * message sent from the host to target for every add/delete flow entry to flow
 * table.
 *
 * Header fields:
 *  dword0 - b'7:0   - msg_type: This will be set to
 *                     0x13 (HTT_H2T_MSG_TYPE_RX_FSE_OPERATION_CFG)
 *           b'15:8  - pdev_id:  0 indicates msg is for all LMAC rings, i.e. soc
 *                     1, 2, 3 indicates pdev_id 0,1,2 and the msg is for the
 *                     specified pdev's LMAC ring.
 *           b'31:16 - reserved : Reserved for future use
 *  dword1 - b'0     - ipsec_valid: This indicates protocol IP or IPsec
 *                     (Internet Protocol Security).
 *                     IPsec describes the framework for providing security at
 *                     IP layer. IPsec is defined for both versions of IP:
 *                     IPV4 and IPV6.
 *                     Please refer to htt_rx_flow_proto enumeration below for
 *                     more info.
 *                         ipsec_valid = 1 for IPSEC packets
 *                         ipsec_valid = 0 for IP Packets
 *           b'7:1   - operation: This indicates types of FSE operation.
 *                     Refer to htt_rx_fse_operation enumeration:
 *                         0 - No Cache Invalidation required
 *                         1 - Cache invalidate only one entry given by IP
 *                             src/dest address at DWORD[2:9]
 *                         2 - Complete FSE Cache Invalidation
 *                         3 - FSE Disable
 *                         4 - FSE Enable
 *           b'31:8  - reserved: Reserved for future use
 *  dword2:9-b'31:0  - IP src/dest: IPV4/IPV6 source and destination address
 *                     for per flow addition/deletion
 *                     For IPV4 src/dest addresses, the first A_UINT32 is used
 *                     and the subsequent 3 A_UINT32 will be padding bytes.
 *                     For IPV6 src/dest Addresses, all A_UINT32 are used.
 *  dword10 -b'31:0  - L4 src port (15:0): 16-bit Source Port numbers range
 *                     from 0 to 65535 but only 0 to 1023 are designated as
 *                     well-known ports. Refer to [RFC1700] for more details.
 *                     This field is valid only if
 *                         (valid_ip_proto(l4_proto) && (ipsec_valid == 0))
 *                   - L4 dest port (31:16): 16-bit Destination Port numbers
 *                     range from 0 to 65535 but only 0 to 1023 are designated
 *                     as well-known ports. Refer to [RFC1700] for more details.
 *                     This field is valid only if
 *                         (valid_ip_proto(l4_proto) && (ipsec_valid == 0))
 *                   - SPI (31:0): Security Parameters Index is an
 *                     identification tag added to the header while using IPsec
 *                     for tunneling the IP traffici.
 *                     Valid only if IPSec_valid bit (in DWORD1) is set to 1.
 *  dword11 -b'7:0   - l4_proto: This carries L4 protocol numbers, which are
 *                     Assigned Internet Protocol Numbers.
 *                     l4_proto numbers for standard protocol like UDP/TCP
 *                     protocol at l4 layer, e.g. l4_proto = 6 for TCP,
 *                     l4_proto = 17 for UDP etc.
 *           b'31:8  - reserved: Reserved for future use.
 *
 */

PREPACK struct htt_h2t_msg_rx_fse_operation_t {
        A_UINT32 msg_type:8,
                 pdev_id:8,
                 reserved0:16;
        A_UINT32 ipsec_valid:1,
                 operation:7,
                 reserved1:24;
        A_UINT32 ip_src_addr_31_0;
        A_UINT32 ip_src_addr_63_32;
        A_UINT32 ip_src_addr_95_64;
        A_UINT32 ip_src_addr_127_96;
        A_UINT32 ip_dest_addr_31_0;
        A_UINT32 ip_dest_addr_63_32;
        A_UINT32 ip_dest_addr_95_64;
        A_UINT32 ip_dest_addr_127_96;
        union {
           A_UINT32 spi;
           struct {
             A_UINT32 l4_src_port:16,
                      l4_dest_port:16;
            } ip;
        } u;
        A_UINT32 l4_proto:8,
                 reserved:24;
} POSTPACK;

/**
 * @brief Host-->target HTT RX Full monitor mode register configuration message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE
 *
 * @details
 * The host will send this Full monitor mode register configuration message.
 * This message can be sent per SOC or per PDEV which is differentiated
 * by pdev id values.
 *
 *       |31                            16|15  11|10   8|7      3|2|1|0|
 *       |-------------------------------------------------------------|
 *       |             reserved           |   pdev_id   |  MSG_TYPE    |
 *       |-------------------------------------------------------------|
 *       |                      reserved         |Release Ring   |N|Z|E|
 *       |-------------------------------------------------------------|
 *
 * where E  is 1-bit full monitor mode enable/disable.
 *       Z  is 1-bit additional descriptor for zero mpdu enable/disable
 *       N  is 1-bit additional descriptor for non zero mdpu enable/disable
 *
 * The following field definitions describe the format of the full monitor
 * mode configuration message sent from the host to target for each pdev.
 *
 * Header fields:
 *  dword0 - b'7:0   - msg_type: This will be set to
 *                     0x17 (HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE)
 *           b'15:8  - pdev_id:  0 indicates msg is for all LMAC rings, i.e. soc
 *                     1, 2, 3 indicates pdev_id 0,1,2 and the msg is for the
 *                     specified pdev's LMAC ring.
 *           b'31:16 - reserved : Reserved for future use.
 *  dword1 - b'0     - full_monitor_mode enable: This indicates that the full
 *                     monitor mode rxdma register is to be enabled or disabled.
 *           b'1     - addnl_descs_zero_mpdus_end: This indicates that the
 *                     additional descriptors at ppdu end for zero mpdus
 *                     enabled or disabled.
 *           b'2     - addnl_descs_non_zero_mpdus_end: This indicates that the
 *                     additional descriptors at ppdu end for non zero mpdus
 *                     enabled or disabled.
 *           b'10:3  - release_ring: This indicates the destination ring
 *                     selection for the descriptor at the end of PPDU
 *                     0 - REO ring select
 *                     1 - FW  ring select
 *                     2 - SW  ring select
 *                     3 - Release ring select
 *                     Refer to htt_rx_full_mon_release_ring.
 *           b'31:11  - reserved for future use
 */
PREPACK struct htt_h2t_msg_rx_full_monitor_mode_t {
    A_UINT32 msg_type:8,
             pdev_id:8,
             reserved0:16;
    A_UINT32 full_monitor_mode_enable:1,
             addnl_descs_zero_mpdus_end:1,
             addnl_descs_non_zero_mpdus_end:1,
             release_ring:8,
             reserved1:21;
} POSTPACK;

/**
 * Enumeration for full monitor mode destination ring select
 * 0 - REO destination ring select
 * 1 - FW destination ring select
 * 2 - SW destination ring select
 * 3 - Release destination ring select
 */
enum htt_rx_full_mon_release_ring {
    HTT_RX_MON_RING_REO,
    HTT_RX_MON_RING_FW,
    HTT_RX_MON_RING_SW,
    HTT_RX_MON_RING_RELEASE,
};

#define HTT_RX_FULL_MONITOR_MODE_SETUP_SZ    (sizeof(struct htt_h2t_msg_rx_full_monitor_mode_t))
/* DWORD 0: Pdev ID */
#define HTT_RX_FULL_MONITOR_MODE_OPERATION_PDEV_ID_M                  0x0000ff00
#define HTT_RX_FULL_MONITOR_MODE_OPERATION_PDEV_ID_S                  8
#define HTT_RX_FULL_MONITOR_MODE_OPERATION_PDEV_ID_GET(_var) \
    (((_var) & HTT_RX_FULL_MONITOR_MODE_OPERATION_PDEV_ID_M) >> \
     HTT_RX_FULL_MONITOR_MODE_OPERATION_PDEV_ID_S)
#define HTT_RX_FULL_MONITOR_MODE_OPERATION_PDEV_ID_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_FULL_MONITOR_MODE_OPERATION_PDEV_ID, _val); \
        ((_var) |= ((_val) << HTT_RX_FULL_MONITOR_MODE_OPERATION_PDEV_ID_S)); \
    } while (0)

/* DWORD 1:ENABLE */
#define HTT_RX_FULL_MONITOR_MODE_ENABLE_M      0x00000001
#define HTT_RX_FULL_MONITOR_MODE_ENABLE_S      0

#define HTT_RX_FULL_MONITOR_MODE_ENABLE_SET(word, enable)           \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_FULL_MONITOR_MODE_ENABLE, enable); \
        (word) |= ((enable) << HTT_RX_FULL_MONITOR_MODE_ENABLE_S);  \
    } while (0)
#define HTT_RX_FULL_MONITOR_MODE_ENABLE_GET(word) \
    (((word) & HTT_RX_FULL_MONITOR_MODE_ENABLE_M) >> HTT_RX_FULL_MONITOR_MODE_ENABLE_S)

/* DWORD 1:ZERO_MPDU */
#define HTT_RX_FULL_MONITOR_MODE_ZERO_MPDU_M      0x00000002
#define HTT_RX_FULL_MONITOR_MODE_ZERO_MPDU_S      1
#define HTT_RX_FULL_MONITOR_MODE_ZERO_MPDU_SET(word, zerompdu)           \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_FULL_MONITOR_MODE_ZERO_MPDU, zerompdu); \
        (word) |= ((zerompdu) << HTT_RX_FULL_MONITOR_MODE_ZERO_MPDU_S);  \
    } while (0)
#define HTT_RX_FULL_MONITOR_MODE_ZERO_MPDU_GET(word) \
    (((word) & HTT_RX_FULL_MONITOR_MODE_ZERO_MPDU_M) >> HTT_RX_FULL_MONITOR_MODE_ZERO_MPDU_S)


/* DWORD 1:NON_ZERO_MPDU */
#define HTT_RX_FULL_MONITOR_MODE_NON_ZERO_MPDU_M      0x00000004
#define HTT_RX_FULL_MONITOR_MODE_NON_ZERO_MPDU_S      2
#define HTT_RX_FULL_MONITOR_MODE_NON_ZERO_MPDU_SET(word, nonzerompdu)           \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_FULL_MONITOR_MODE_NON_ZERO_MPDU, nonzerompdu); \
        (word) |= ((nonzerompdu) << HTT_RX_FULL_MONITOR_MODE_NON_ZERO_MPDU_S);  \
    } while (0)
#define HTT_RX_FULL_MONITOR_MODE_NON_ZERO_MPDU_GET(word) \
    (((word) & HTT_RX_FULL_MONITOR_MODE_NON_ZERO_MPDU_M) >> HTT_RX_FULL_MONITOR_MODE_NON_ZERO_MPDU_S)

/* DWORD 1:RELEASE_RINGS */
#define HTT_RX_FULL_MONITOR_MODE_RELEASE_RINGS_M      0x000007f8
#define HTT_RX_FULL_MONITOR_MODE_RELEASE_RINGS_S      3
#define HTT_RX_FULL_MONITOR_MODE_RELEASE_RINGS_SET(word, releaserings)           \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_FULL_MONITOR_MODE_RELEASE_RINGS, releaserings); \
        (word) |= ((releaserings) << HTT_RX_FULL_MONITOR_MODE_RELEASE_RINGS_S);  \
    } while (0)
#define HTT_RX_FULL_MONITOR_MODE_RELEASE_RINGS_GET(word) \
    (((word) & HTT_RX_FULL_MONITOR_MODE_RELEASE_RINGS_M) >> HTT_RX_FULL_MONITOR_MODE_RELEASE_RINGS_S)

/**
 * Enumeration for IP Protocol or IPSEC Protocol
 * IPsec describes the framework for providing security at IP layer.
 * IPsec is defined for both versions of IP: IPV4 and IPV6.
 */
enum htt_rx_flow_proto {
        HTT_RX_FLOW_IP_PROTO,
        HTT_RX_FLOW_IPSEC_PROTO,
};

/**
 * Enumeration for FSE Cache Invalidation
 * 0 - No Cache Invalidation required
 * 1 - Cache invalidate only one entry given by IP src/dest address at DWORD2:9
 * 2 - Complete FSE Cache Invalidation
 * 3 - FSE Disable
 * 4 - FSE Enable
 */
enum htt_rx_fse_operation {
        HTT_RX_FSE_CACHE_INVALIDATE_NONE,
        HTT_RX_FSE_CACHE_INVALIDATE_ENTRY,
        HTT_RX_FSE_CACHE_INVALIDATE_FULL,
        HTT_RX_FSE_DISABLE,
        HTT_RX_FSE_ENABLE,
};

/* DWORD 0: Pdev ID */
#define HTT_RX_FSE_OPERATION_PDEV_ID_M                  0x0000ff00
#define HTT_RX_FSE_OPERATION_PDEV_ID_S                  8
#define HTT_RX_FSE_OPERATION_PDEV_ID_GET(_var) \
        (((_var) & HTT_RX_FSE_OPERATION_PDEV_ID_M) >> \
                HTT_RX_FSE_OPERATION_PDEV_ID_S)
#define HTT_RX_FSE_OPERATION_PDEV_ID_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_RX_FSE_OPERATION_PDEV_ID, _val); \
            ((_var) |= ((_val) << HTT_RX_FSE_OPERATION_PDEV_ID_S)); \
        } while (0)

/* DWORD 1:IP PROTO or IPSEC */
#define HTT_RX_FSE_IPSEC_VALID_M      0x00000001
#define HTT_RX_FSE_IPSEC_VALID_S      0

#define HTT_RX_FSE_IPSEC_VALID_SET(word, ipsec_valid)           \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_IPSEC_VALID, ipsec_valid); \
          (word) |= ((ipsec_valid) << HTT_RX_FSE_IPSEC_VALID_S);  \
      } while (0)
#define HTT_RX_FSE_IPSEC_VALID_GET(word) \
        (((word) & HTT_RX_FSE_IPSEC_VALID_M) >> HTT_RX_FSE_IPSEC_VALID_S)

/* DWORD 1:FSE Operation */
#define HTT_RX_FSE_OPERATION_M      0x000000fe
#define HTT_RX_FSE_OPERATION_S      1

#define HTT_RX_FSE_OPERATION_SET(word, op_val)           \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_OPERATION, op_val); \
          (word) |= ((op_val) << HTT_RX_FSE_OPERATION_S);  \
      } while (0)
#define HTT_RX_FSE_OPERATION_GET(word) \
        (((word) & HTT_RX_FSE_OPERATION_M) >> HTT_RX_FSE_OPERATION_S)

/* DWORD 2-9:IP Address */
#define HTT_RX_FSE_OPERATION_IP_ADDR_M        0xffffffff
#define HTT_RX_FSE_OPERATION_IP_ADDR_S        0
#define HTT_RX_FSE_OPERATION_IP_ADDR_GET(_var) \
        (((_var) & HTT_RX_FSE_OPERATION_IP_ADDR_M) >> \
            HTT_RX_FSE_OPERATION_IP_ADDR_S)
#define HTT_RX_FSE_OPERATION_IP_ADDR_SET(_var, _val) \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_OPERATION_IP_ADDR, _val); \
          ((_var) |= ((_val) << HTT_RX_FSE_OPERATION_IP_ADDR_S)); \
      } while (0)

/* DWORD 10:Source Port Number */
#define HTT_RX_FSE_SOURCEPORT_M      0x0000ffff
#define HTT_RX_FSE_SOURCEPORT_S      0

#define HTT_RX_FSE_SOURCEPORT_SET(word, sport)           \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_SOURCEPORT, sport); \
          (word) |= ((sport) << HTT_RX_FSE_SOURCEPORT_S);  \
      } while (0)
#define HTT_RX_FSE_SOURCEPORT_GET(word) \
        (((word) & HTT_RX_FSE_SOURCEPORT_M) >> HTT_RX_FSE_SOURCEPORT_S)


/* DWORD 11:Destination Port Number */
#define HTT_RX_FSE_DESTPORT_M      0xffff0000
#define HTT_RX_FSE_DESTPORT_S      16

#define HTT_RX_FSE_DESTPORT_SET(word, dport)           \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_DESTPORT, dport); \
          (word) |= ((dport) << HTT_RX_FSE_DESTPORT_S);  \
      } while (0)
#define HTT_RX_FSE_DESTPORT_GET(word) \
        (((word) & HTT_RX_FSE_DESTPORT_M) >> HTT_RX_FSE_DESTPORT_S)

/* DWORD 10-11:SPI (In case of IPSEC) */
#define HTT_RX_FSE_OPERATION_SPI_M        0xffffffff
#define HTT_RX_FSE_OPERATION_SPI_S        0
#define HTT_RX_FSE_OPERATION_SPI_GET(_var) \
        (((_var) & HTT_RX_FSE_OPERATION_SPI_ADDR_M) >> \
            HTT_RX_FSE_OPERATION_SPI_ADDR_S)
#define HTT_RX_FSE_OPERATION_SPI_SET(_var, _val) \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_OPERATION_SPI, _val); \
          ((_var) |= ((_val) << HTT_RX_FSE_OPERATION_SPI_S)); \
      } while (0)

/* DWORD 12:L4 PROTO */
#define HTT_RX_FSE_L4_PROTO_M      0x000000ff
#define HTT_RX_FSE_L4_PROTO_S      0

#define HTT_RX_FSE_L4_PROTO_SET(word, proto_val)           \
   do { \
          HTT_CHECK_SET_VAL(HTT_RX_FSE_L4_PROTO, proto_val); \
          (word) |= ((proto_val) << HTT_RX_FSE_L4_PROTO_S);  \
      } while (0)
#define HTT_RX_FSE_L4_PROTO_GET(word) \
        (((word) & HTT_RX_FSE_L4_PROTO_M) >> HTT_RX_FSE_L4_PROTO_S)


/**
 * @brief host --> target Receive to configure the RxOLE 3-tuple Hash
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_3_TUPLE_HASH_CFG
 *
 *     |31            24|23              |15             8|7          2|1|0|
 *     |----------------+----------------+----------------+----------------|
 *     |              reserved           |    pdev_id     |    msg_type    |
 *     |---------------------------------+----------------+----------------|
 *     |                        reserved                               |E|F|
 *     |---------------------------------+----------------+----------------|
 *     Where E = Configure the target to provide the 3-tuple hash value in
 *                      toeplitz_hash_2_or_4 field of rx_msdu_start tlv
 *           F = Configure the target to provide the 3-tuple hash value in
 *                      flow_id_toeplitz field of rx_msdu_start tlv
 *
 * The following field definitions describe the format of the 3 tuple hash value
 * message sent from the host to target as part of initialization sequence.
 *
 * Header fields:
 *  dword0 - b'7:0   - msg_type: This will be set to
 *                     0x16 (HTT_H2T_MSG_TYPE_3_TUPLE_HASH_CFG)
 *           b'15:8  - pdev_id:  0 indicates msg is for all LMAC rings, i.e. soc
 *                     1, 2, 3 indicates pdev_id 0,1,2 and the msg is for the
 *                     specified pdev's LMAC ring.
 *           b'31:16 - reserved : Reserved for future use
 *  dword1 - b'0     - flow_id_toeplitz_field_enable
 *           b'1     - toeplitz_hash_2_or_4_field_enable
 *           b'31:2  - reserved : Reserved for future use
 * ---------+------+----------------------------------------------------------
 *     bit1 | bit0 |   Functionality
 * ---------+------+----------------------------------------------------------
 *       0  |   1  |   Configure the target to provide the 3 tuple hash value
 *          |      |   in flow_id_toeplitz field
 * ---------+------+----------------------------------------------------------
 *       1  |   0  |   Configure the target to provide the 3 tuple hash value
 *          |      |   in toeplitz_hash_2_or_4 field
 * ---------+------+----------------------------------------------------------
 *       1  |   1  |   Configure the target to provide the 3 tuple hash value
 *          |      |   in both flow_id_toeplitz & toeplitz_hash_2_or_4 field
 * ---------+------+----------------------------------------------------------
 *       0  |   0  |   Configure the target to provide the 5 tuple hash value
 *          |      |   in flow_id_toeplitz field 2 or 4 tuple has value in
 *          |      |   toeplitz_hash_2_or_4 field
 *----------------------------------------------------------------------------
 */
PREPACK struct htt_h2t_msg_rx_3_tuple_hash_cfg_t {
    A_UINT32 msg_type                          :8,
             pdev_id                           :8,
             reserved0                         :16;
    A_UINT32 flow_id_toeplitz_field_enable     :1,
             toeplitz_hash_2_or_4_field_enable :1,
             reserved1                         :30;
} POSTPACK;

/* DWORD0 : pdev_id configuration Macros */
#define HTT_H2T_3_TUPLE_HASH_PDEV_ID_M                  0xff00
#define HTT_H2T_3_TUPLE_HASH_PDEV_ID_S                  8
#define HTT_RX_3_TUPLE_HASH_PDEV_ID_GET(_var) \
        (((_var) & HTT_H2T_3_TUPLE_HASH_PDEV_ID_M) >> \
                HTT_H2T_3_TUPLE_HASH_PDEV_ID_S)
#define HTT_RX_3_TUPLE_HASH_PDEV_ID_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_H2T_3_TUPLE_HASH_PDEV_ID, _val); \
            ((_var) |= ((_val) << HTT_H2T_3_TUPLE_HASH_PDEV_ID_S)); \
        } while (0)

/* DWORD1: rx 3 tuple hash value reception field configuration Macros */
#define HTT_H2T_FLOW_ID_TOEPLITZ_FIELD_CONFIG_M         0x1
#define HTT_H2T_FLOW_ID_TOEPLITZ_FIELD_CONFIG_S         0
#define HTT_FLOW_ID_TOEPLITZ_FIELD_CONFIG_GET(_var)    \
    (((_var) & HTT_H2T_FLOW_ID_TOEPLITZ_FIELD_CONFIG_M) >> \
        HTT_H2T_FLOW_ID_TOEPLITZ_FIELD_CONFIG_S)
#define HTT_H2T_FLOW_ID_TOEPLITZ_FIELD_CONFIG_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_H2T_FLOW_ID_TOEPLITZ_FIELD_CONFIG, _val); \
        ((_var) |= ((_val) << HTT_H2T_FLOW_ID_TOEPLITZ_FIELD_CONFIG_S)); \
    } while (0)

#define HTT_H2T_TOEPLITZ_2_OR_4_FIELD_CONFIG_M         0x2
#define HTT_H2T_TOEPLITZ_2_OR_4_FIELD_CONFIG_S         1
#define HTT_TOEPLITZ_2_OR_4_FIELD_CONFIG_GET(_var)    \
    (((_var) & HTT_H2T_TOEPLITZ_2_OR_4_FIELD_CONFIG_M) >> \
        HTT_H2T_TOEPLITZ_2_OR_4_FIELD_CONFIG_S)
#define HTT_H2T_TOEPLITZ_2_OR_4_FIELD_CONFIG_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_H2T_TOEPLITZ_2_OR_4_FIELD_CONFIG, _val); \
        ((_var) |= ((_val) << HTT_H2T_TOEPLITZ_2_OR_4_FIELD_CONFIG_S)); \
    } while (0)

#define HTT_3_TUPLE_HASH_CFG_REQ_BYTES     8

/**
 * @brief host --> target Host PA Address Size
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_HOST_PADDR_SIZE
 *
 * @details
 *  The HTT_H2T_MSG_TYPE_HOST_PADDR_SIZE message is sent by the host to
 *  provide the physical start address and size of each of the memory
 *  areas within host DDR that the target FW may need to access.
 *
 *  For example, the host can use this message to allow the target FW
 *  to set up access to the host's pools of TQM link descriptors.
 *  The message would appear as follows:
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |             reserved            |  num_entries   |   msg_type     |
 *     |-=-=-=-=-=-=-=-=+-=-=-=-=-=-=-=-=+=-=-=-=-=-=-=-=-+=-=-=-=-=-=-=-=-|
 *     |                          mem area 0 size                          |
 *     |----------------+----------------+----------------+----------------|
 *     |                    mem area 0 physical_address_lo                 |
 *     |----------------+----------------+----------------+----------------|
 *     |                    mem area 0 physical_address_hi                 |
 *     |-=-=-=-=-=-=-=-=+-=-=-=-=-=-=-=-=+=-=-=-=-=-=-=-=-+=-=-=-=-=-=-=-=-|
 *     |                          mem area 1 size                          |
 *     |----------------+----------------+----------------+----------------|
 *     |                    mem area 1 physical_address_lo                 |
 *     |----------------+----------------+----------------+----------------|
 *     |                    mem area 1 physical_address_hi                 |
 *     |----------------+----------------+----------------+----------------|
 *                                      ...
 *     |-=-=-=-=-=-=-=-=+-=-=-=-=-=-=-=-=+=-=-=-=-=-=-=-=-+=-=-=-=-=-=-=-=-|
 *     |                          mem area N size                          |
 *     |----------------+----------------+----------------+----------------|
 *     |                    mem area N physical_address_lo                 |
 *     |----------------+----------------+----------------+----------------|
 *     |                    mem area N physical_address_hi                 |
 *     |----------------+----------------+----------------+----------------|
 *
 * The message is interpreted as follows:
 * dword0 - b'0:7   - msg_type: This will be set to
 *                    0x18 (HTT_H2T_MSG_TYPE_HOST_PADDR_SIZE)
 *          b'8:15  - number_entries: Indicated the number of host memory
 *                    areas specified within the remainder of the message
 *          b'16:31 - reserved.
 * dword1 - b'0:31  - memory area 0 size in bytes
 * dword2 - b'0:31  - memory area 0 physical address, lower 32 bits
 * dword3 - b'0:31  - memory area 0 physical address, upper 32 bits
 * and similar for memory area 1 through memory area N.
 */

PREPACK struct htt_h2t_host_paddr_size {
    A_UINT32 msg_type:      8,
             num_entries:   8,
             reserved:     16;
} POSTPACK;

PREPACK struct htt_h2t_host_paddr_size_entry_t {
    A_UINT32 size;
    A_UINT32 physical_address_lo;
    A_UINT32 physical_address_hi;
} POSTPACK;

#define HTT_H2T_HOST_PADDR_SIZE_ENTRY_SIZE  (sizeof(struct htt_h2t_host_paddr_size_entry_t))

#define HTT_H2T_HOST_PADDR_SIZE_NUM_ENTRIES_M 0x0000FF00
#define HTT_H2T_HOST_PADDR_SIZE_NUM_ENTRIES_S 8

#define HTT_H2T_HOST_PADDR_SIZE_NUM_ENTRIES_GET(_var) \
    (((_var) & HTT_H2T_HOST_PADDR_SIZE_NUM_ENTRIES_M) >> \
    HTT_H2T_HOST_PADDR_SIZE_NUM_ENTRIES_S)

#define HTT_H2T_HOST_PADDR_SIZE_NUM_ENTRIES_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_H2T_HOST_PADDR_SIZE_NUM_ENTRIES, _val); \
        ((_var) |= ((_val) << HTT_H2T_HOST_PADDR_SIZE_NUM_ENTRIES_S)); \
    } while (0)

/**
 * @brief host --> target Host RXDMA RXOLE PPE register configuration
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_RXDMA_RXOLE_PPE_CFG
 *
 * @details
 *  The HTT_H2T_MSG_TYPE_RXDMA_RXOLE_PPE_CFG message is sent by the host to
 *  provide the PPE DS register confiuration for RXOLE and RXDMA.
 *
 *  The message would appear as follows:
 *
 *     |31                 19|18 |17 |16 |15 |14 |13       9|8|7         0|
 *     |---------------------------------+---+---+----------+-+-----------|
 *     |      reserved       |IFO|DNO|DRO|IBO|MIO|   RDI    |O| msg_type  |
 *     |---------------------+---+---+---+---+---+----------+-+-----------|
 *
 *
 * The message is interpreted as follows:
 * dword0 - b'0:7   - msg_type: This will be set to
 *                    0x19 (HTT_H2T_MSG_TYPE_RXDMA_RXOLE_PPE_CFG)
 *          b'8     - override bit to drive MSDUs to PPE ring
 *          b'9:13  - REO destination ring indication
 *          b'14    - Multi buffer msdu override enable bit
 *          b'15    - Intra BSS override
 *          b'16    - Decap raw override
 *          b'17    - Decap Native wifi override
 *          b'18    - IP frag override
 *          b'19:31 - reserved
 */
PREPACK struct htt_h2t_msg_type_rxdma_rxole_ppe_cfg_t {
   A_UINT32 msg_type:                      8, /* HTT_H2T_MSG_TYPE_RXDMA_RXOLE_PPE_CFG */
            override:                      1,
            reo_destination_indication:    5,
            multi_buffer_msdu_override_en: 1,
            intra_bss_override:            1,
            decap_raw_override:            1,
            decap_nwifi_override:          1,
            ip_frag_override:              1,
            reserved:                     13;
} POSTPACK;

/* DWORD 0: Override */
#define HTT_PPE_CFG_OVERRIDE_M                  0x00000100
#define HTT_PPE_CFG_OVERRIDE_S                  8
#define HTT_PPE_CFG_OVERRIDE_GET(_var) \
        (((_var) & HTT_PPE_CFG_OVERRIDE_M) >> \
                HTT_PPE_CFG_OVERRIDE_S)
#define HTT_PPE_CFG_OVERRIDE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_PPE_CFG_OVERRIDE, _val); \
            ((_var) |= ((_val) << HTT_PPE_CFG_OVERRIDE_S)); \
        } while (0)

/* DWORD 0: REO Destination Indication*/
#define HTT_PPE_CFG_REO_DEST_IND_M                  0x00003E00
#define HTT_PPE_CFG_REO_DEST_IND_S                  9
#define HTT_PPE_CFG_REO_DEST_IND_GET(_var) \
        (((_var) & HTT_PPE_CFG_REO_DEST_IND_M) >> \
                HTT_PPE_CFG_REO_DEST_IND_S)
#define HTT_PPE_CFG_REO_DEST_IND_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_PPE_CFG_REO_DEST_IND, _val); \
            ((_var) |= ((_val) << HTT_PPE_CFG_REO_DEST_IND_S)); \
        } while (0)

/* DWORD 0: Multi buffer MSDU override */
#define HTT_PPE_CFG_MULTI_BUF_MSDU_OVERRIDE_EN_M                  0x00004000
#define HTT_PPE_CFG_MULTI_BUF_MSDU_OVERRIDE_EN_S                  14
#define HTT_PPE_CFG_MULTI_BUF_MSDU_OVERRIDE_EN_GET(_var) \
        (((_var) & HTT_PPE_CFG_MULTI_BUF_MSDU_OVERRIDE_EN_M) >> \
                HTT_PPE_CFG_MULTI_BUF_MSDU_OVERRIDE_EN_S)
#define HTT_PPE_CFG_MULTI_BUF_MSDU_OVERRIDE_EN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_PPE_CFG_MULTI_BUF_MSDU_OVERRIDE_EN, _val); \
            ((_var) |= ((_val) << HTT_PPE_CFG_MULTI_BUF_MSDU_OVERRIDE_EN_S)); \
        } while (0)

/* DWORD 0: Intra BSS override */
#define HTT_PPE_CFG_INTRA_BSS_OVERRIDE_EN_M                  0x00008000
#define HTT_PPE_CFG_INTRA_BSS_OVERRIDE_EN_S                  15
#define HTT_PPE_CFG_INTRA_BSS_OVERRIDE_EN_GET(_var) \
        (((_var) & HTT_PPE_CFG_INTRA_BSS_OVERRIDE_EN_M) >> \
                HTT_PPE_CFG_INTRA_BSS_OVERRIDE_EN_S)
#define HTT_PPE_CFG_INTRA_BSS_OVERRIDE_EN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_PPE_CFG_INTRA_BSS_OVERRIDE_EN, _val); \
            ((_var) |= ((_val) << HTT_PPE_CFG_INTRA_BSS_OVERRIDE_EN_S)); \
        } while (0)

/* DWORD 0: Decap RAW override */
#define HTT_PPE_CFG_DECAP_RAW_OVERRIDE_EN_M                  0x00010000
#define HTT_PPE_CFG_DECAP_RAW_OVERRIDE_EN_S                  16
#define HTT_PPE_CFG_DECAP_RAW_OVERRIDE_EN_GET(_var) \
        (((_var) & HTT_PPE_CFG_DECAP_RAW_OVERRIDE_EN_M) >> \
                HTT_PPE_CFG_DECAP_RAW_OVERRIDE_EN_S)
#define HTT_PPE_CFG_DECAP_RAW_OVERRIDE_EN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_PPE_CFG_DECAP_RAW_OVERRIDE_EN, _val); \
            ((_var) |= ((_val) << HTT_PPE_CFG_DECAP_RAW_OVERRIDE_EN_S)); \
        } while (0)

/* DWORD 0: Decap NWIFI override */
#define HTT_PPE_CFG_DECAP_NWIFI_OVERRIDE_EN_M                  0x00020000
#define HTT_PPE_CFG_DECAP_NWIFI_OVERRIDE_EN_S                  17
#define HTT_PPE_CFG_DECAP_NWIFI_OVERRIDE_EN_GET(_var) \
        (((_var) & HTT_PPE_CFG_DECAP_NWIFI_OVERRIDE_EN_M) >> \
                HTT_PPE_CFG_DECAP_NWIFI_OVERRIDE_EN_S)
#define HTT_PPE_CFG_DECAP_NWIFI_OVERRIDE_EN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_PPE_CFG_DECAP_NWIFI_OVERRIDE_EN, _val); \
            ((_var) |= ((_val) << HTT_PPE_CFG_DECAP_NWIFI_OVERRIDE_EN_S)); \
        } while (0)

/* DWORD 0: IP frag override */
#define HTT_PPE_CFG_IP_FRAG_OVERRIDE_EN_M                  0x00040000
#define HTT_PPE_CFG_IP_FRAG_OVERRIDE_EN_S                  18
#define HTT_PPE_CFG_IP_FRAG_OVERRIDE_EN_GET(_var) \
        (((_var) & HTT_PPE_CFG_IP_FRAG_OVERRIDE_EN_M) >> \
                HTT_PPE_CFG_IP_FRAG_OVERRIDE_EN_S)
#define HTT_PPE_CFG_IP_FRAG_OVERRIDE_EN_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_PPE_CFG_IP_FRAG_OVERRIDE_EN, _val); \
            ((_var) |= ((_val) << HTT_PPE_CFG_IP_FRAG_OVERRIDE_EN_S)); \
        } while (0)

/*
 * MSG_TYPE => HTT_H2T_MSG_TYPE_VDEVS_TXRX_STATS_CFG
 *
 * @details
 * The following field definitions describe the format of the HTT host
 * to target FW VDEV TX RX stats retrieve message.
 * The message specifies the type of stats the host wants to retrieve.
 *
 * |31  27|26 25|24         17|16|15           8|7            0|
 * |-----------------------------------------------------------|
 * | rsvd |  R  | Periodic Int| E|    pdev_id   |   msg type   |
 * |-----------------------------------------------------------|
 * |                  vdev_id lower bitmask                    |
 * |-----------------------------------------------------------|
 * |                  vdev_id upper bitmask                    |
 * |-----------------------------------------------------------|
 * Header fields:
 * Where:
 * dword0 - b'7:0       - msg_type: This will be set to
 *                        0x1a (HTT_H2T_MSG_TYPE_VDEVS_TXRX_STATS_CFG)
 *          b'15:8      - pdev id
 *          b'16(E)     - Enable/Disable the vdev HW stats
 *          b'17:24(PI) - Periodic Interval, units = 8 ms, e.g. 125 -> 1000 ms
 *          b'25:26(R)  - Reset stats bits
 *                        0: don't reset stats
 *                        1: reset stats once
 *                        2: reset stats at the start of each periodic interval
 *          b'27:31     - reserved for future use
 * dword1 - b'0:31      - vdev_id lower bitmask
 * dword2 - b'0:31      - vdev_id upper bitmask
 */

PREPACK struct htt_h2t_vdevs_txrx_stats_cfg {
    A_UINT32 msg_type          :8,
             pdev_id           :8,
             enable            :1,
             periodic_interval :8,
             reset_stats_bits  :2,
             reserved0         :5;
    A_UINT32 vdev_id_lower_bitmask;
    A_UINT32 vdev_id_upper_bitmask;
} POSTPACK;

#define HTT_H2T_VDEVS_TXRX_STATS_PDEV_ID_M                           0xFF00
#define HTT_H2T_VDEVS_TXRX_STATS_PDEV_ID_S                           8
#define HTT_H2T_VDEVS_TXRX_STATS_PDEV_ID_GET(_var) \
        (((_var) & HTT_H2T_VDEVS_TXRX_STATS_PDEV_ID_M) >> \
                HTT_H2T_VDEVS_TXRX_STATS_PDEV_ID_S)
#define HTT_RX_VDEVS_TXRX_STATS_PDEV_ID_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_H2T_VDEVS_TXRX_STATS_PDEV_ID, _val); \
            ((_var) |= ((_val) << HTT_H2T_VDEVS_TXRX_STATS_PDEV_ID_S)); \
        } while (0)

#define HTT_H2T_VDEVS_TXRX_STATS_ENABLE_M                            0x10000
#define HTT_H2T_VDEVS_TXRX_STATS_ENABLE_S                            16
#define HTT_H2T_VDEVS_TXRX_STATS_ENABLE_GET(_var) \
        (((_var) & HTT_H2T_VDEVS_TXRX_STATS_ENABLE_M) >> \
                HTT_H2T_VDEVS_TXRX_STATS_ENABLE_S)
#define HTT_RX_VDEVS_TXRX_STATS_ENABLE_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_H2T_VDEVS_TXRX_STATS_ENABLE, _val); \
            ((_var) |= ((_val) << HTT_H2T_VDEVS_TXRX_STATS_ENABLE_S)); \
        } while (0)

#define HTT_H2T_VDEVS_TXRX_STATS_PERIODIC_INTERVAL_M                 0x1FE0000
#define HTT_H2T_VDEVS_TXRX_STATS_PERIODIC_INTERVAL_S                 17
#define HTT_H2T_VDEVS_TXRX_STATS_PERIODIC_INTERVAL_GET(_var) \
        (((_var) & HTT_H2T_VDEVS_TXRX_STATS_PERIODIC_INTERVAL_M) >> \
                HTT_H2T_VDEVS_TXRX_STATS_PERIODIC_INTERVAL_S)
#define HTT_RX_VDEVS_TXRX_STATS_PERIODIC_INTERVAL_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_H2T_VDEVS_TXRX_STATS_PERIODIC_INTERVAL, _val); \
            ((_var) |= ((_val) << HTT_H2T_VDEVS_TXRX_STATS_PERIODIC_INTERVAL_S)); \
        } while (0)

#define HTT_H2T_VDEVS_TXRX_STATS_RESET_STATS_BITS_M                   0x6000000
#define HTT_H2T_VDEVS_TXRX_STATS_RESET_STATS_BITS_S                   25
#define HTT_H2T_VDEVS_TXRX_STATS_RESET_STATS_BITS_GET(_var) \
        (((_var) & HTT_H2T_VDEVS_TXRX_STATS_RESET_STATS_BITS_M) >> \
                HTT_H2T_VDEVS_TXRX_STATS_RESET_STATS_BITS_S)
#define HTT_RX_VDEVS_TXRX_STATS_RESET_STATS_BITS_SET(_var, _val) \
        do { \
            HTT_CHECK_SET_VAL(HTT_H2T_VDEVS_TXRX_STATS_RESET_STATS_BITS, _val); \
            ((_var) |= ((_val) << HTT_H2T_VDEVS_TXRX_STATS_RESET_STATS_BITS_S)); \
        } while (0)



/*=== target -> host messages ===============================================*/


enum htt_t2h_msg_type {
    HTT_T2H_MSG_TYPE_VERSION_CONF                  = 0x0,
    HTT_T2H_MSG_TYPE_RX_IND                        = 0x1,
    HTT_T2H_MSG_TYPE_RX_FLUSH                      = 0x2,
    HTT_T2H_MSG_TYPE_PEER_MAP                      = 0x3,
    HTT_T2H_MSG_TYPE_PEER_UNMAP                    = 0x4,
    HTT_T2H_MSG_TYPE_RX_ADDBA                      = 0x5,
    HTT_T2H_MSG_TYPE_RX_DELBA                      = 0x6,
    HTT_T2H_MSG_TYPE_TX_COMPL_IND                  = 0x7,
    HTT_T2H_MSG_TYPE_PKTLOG                        = 0x8,
    HTT_T2H_MSG_TYPE_STATS_CONF                    = 0x9,
    HTT_T2H_MSG_TYPE_RX_FRAG_IND                   = 0xa,
    HTT_T2H_MSG_TYPE_SEC_IND                       = 0xb,
    DEPRECATED_HTT_T2H_MSG_TYPE_RC_UPDATE_IND      = 0xc, /* no longer used */
    HTT_T2H_MSG_TYPE_TX_INSPECT_IND                = 0xd,
    HTT_T2H_MSG_TYPE_MGMT_TX_COMPL_IND             = 0xe,
    /* only used for HL, add HTT MSG for HTT CREDIT update */
    HTT_T2H_MSG_TYPE_TX_CREDIT_UPDATE_IND          = 0xf,
    HTT_T2H_MSG_TYPE_RX_PN_IND                     = 0x10,
    HTT_T2H_MSG_TYPE_RX_OFFLOAD_DELIVER_IND        = 0x11,
    HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND           = 0x12,
    /* 0x13 is reserved for RX_RING_LOW_IND (RX Full reordering related) */
    HTT_T2H_MSG_TYPE_WDI_IPA_OP_RESPONSE           = 0x14,
    HTT_T2H_MSG_TYPE_CHAN_CHANGE                   = 0x15,
    HTT_T2H_MSG_TYPE_RX_OFLD_PKT_ERR               = 0x16,
    HTT_T2H_MSG_TYPE_RATE_REPORT                   = 0x17,
    HTT_T2H_MSG_TYPE_FLOW_POOL_MAP                 = 0x18,
    HTT_T2H_MSG_TYPE_FLOW_POOL_UNMAP               = 0x19,
    HTT_T2H_MSG_TYPE_SRING_SETUP_DONE              = 0x1a,
    HTT_T2H_MSG_TYPE_MAP_FLOW_INFO                 = 0x1b,
    HTT_T2H_MSG_TYPE_EXT_STATS_CONF                = 0x1c,
    HTT_T2H_MSG_TYPE_PPDU_STATS_IND                = 0x1d,
    HTT_T2H_MSG_TYPE_PEER_MAP_V2                   = 0x1e,
    HTT_T2H_MSG_TYPE_PEER_UNMAP_V2                 = 0x1f,
    HTT_T2H_MSG_TYPE_MONITOR_MAC_HEADER_IND        = 0x20,
    HTT_T2H_MSG_TYPE_FLOW_POOL_RESIZE              = 0x21,
    HTT_T2H_MSG_TYPE_CFR_DUMP_COMPL_IND            = 0x22,
    HTT_T2H_MSG_TYPE_PEER_STATS_IND                = 0x23,
    HTT_T2H_MSG_TYPE_BKPRESSURE_EVENT_IND          = 0x24,
    /* TX_OFFLOAD_DELIVER_IND:
     * Forward the target's locally-generated packets to the host,
     * to provide to the monitor mode interface.
     */
    HTT_T2H_MSG_TYPE_TX_OFFLOAD_DELIVER_IND        = 0x25,
    HTT_T2H_MSG_TYPE_CHAN_CALDATA                  = 0x26,
    HTT_T2H_MSG_TYPE_FSE_CMEM_BASE_SEND            = 0x27,
    HTT_T2H_MSG_TYPE_MLO_TIMESTAMP_OFFSET_IND      = 0x28,
    HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP               = 0x29,
    HTT_T2H_MSG_TYPE_MLO_RX_PEER_UNMAP             = 0x2a,
    HTT_T2H_MSG_TYPE_PEER_MAP_V3                   = 0x2b,
    HTT_T2H_MSG_TYPE_VDEVS_TXRX_STATS_PERIODIC_IND = 0x2c,


    HTT_T2H_MSG_TYPE_TEST,
    /* keep this last */
    HTT_T2H_NUM_MSGS
};

/*
 * HTT target to host message type -
 * stored in bits 7:0 of the first word of the message
 */
#define HTT_T2H_MSG_TYPE_M      0xff
#define HTT_T2H_MSG_TYPE_S      0

#define HTT_T2H_MSG_TYPE_SET(word, msg_type)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_T2H_MSG_TYPE, msg_type); \
        (word) |= ((msg_type) << HTT_T2H_MSG_TYPE_S);  \
    } while (0)
#define HTT_T2H_MSG_TYPE_GET(word) \
    (((word) & HTT_T2H_MSG_TYPE_M) >> HTT_T2H_MSG_TYPE_S)

/**
 * @brief target -> host version number confirmation message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_VERSION_CONF
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |    reserved    |  major number  |  minor number  |    msg type    |
 *     |-------------------------------------------------------------------|
 *     :                    option request TLV (optional)                  |
 *     :...................................................................:
 *
 * The VER_CONF message may consist of a single 4-byte word, or may be
 * extended with TLVs that specify HTT options selected by the target.
 * The following option TLVs may be appended to the VER_CONF message:
 *   - LL_BUS_ADDR_SIZE
 *   - HL_SUPPRESS_TX_COMPL_IND
 *   - MAX_TX_QUEUE_GROUPS
 * These TLVs may appear in an arbitrary order.  Any number of these TLVs
 * may be appended to the VER_CONF message (but only one TLV of each type).
 *
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a version number confirmation message
 *     Value: 0x0 (HTT_T2H_MSG_TYPE_VERSION_CONF)
 *   - VER_MINOR
 *     Bits 15:8
 *     Purpose: Specify the minor number of the HTT message library version
 *         in use by the target firmware.
 *         The minor number specifies the specific revision within a range
 *         of fundamentally compatible HTT message definition revisions.
 *         Compatible revisions involve adding new messages or perhaps
 *         adding new fields to existing messages, in a backwards-compatible
 *         manner.
 *         Incompatible revisions involve changing the message type values,
 *         or redefining existing messages.
 *     Value: minor number
 *   - VER_MAJOR
 *     Bits 15:8
 *     Purpose: Specify the major number of the HTT message library version
 *         in use by the target firmware.
 *         The major number specifies the family of minor revisions that are
 *         fundamentally compatible with each other, but not with prior or
 *         later families.
 *     Value: major number
 */

#define HTT_VER_CONF_MINOR_M      0x0000ff00
#define HTT_VER_CONF_MINOR_S      8
#define HTT_VER_CONF_MAJOR_M      0x00ff0000
#define HTT_VER_CONF_MAJOR_S      16


#define HTT_VER_CONF_MINOR_SET(word, value)                              \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_VER_CONF_MINOR, value);                    \
        (word) |= (value)  << HTT_VER_CONF_MINOR_S;                      \
    } while (0)
#define HTT_VER_CONF_MINOR_GET(word) \
    (((word) & HTT_VER_CONF_MINOR_M) >> HTT_VER_CONF_MINOR_S)

#define HTT_VER_CONF_MAJOR_SET(word, value)                              \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_VER_CONF_MAJOR, value);                    \
        (word) |= (value)  << HTT_VER_CONF_MAJOR_S;                      \
    } while (0)
#define HTT_VER_CONF_MAJOR_GET(word) \
    (((word) & HTT_VER_CONF_MAJOR_M) >> HTT_VER_CONF_MAJOR_S)


#define HTT_VER_CONF_BYTES 4


/**
 * @brief - target -> host HTT Rx In order indication message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
 *
 * @details
 *
 * |31            24|23                 |15|14|13|12|11|10|9|8|7|6|5|4       0|
 * |----------------+-------------------+---------------------+---------------|
 * |                  peer ID           | P| F| O| ext TID    |   msg type    |
 * |--------------------------------------------------------------------------|
 * |                  MSDU count        |        Reserved     |   vdev id     |
 * |--------------------------------------------------------------------------|
 * |                        MSDU 0 bus address (bits 31:0)                    |
#if HTT_PADDR64
 * |                        MSDU 0 bus address (bits 63:32)                   |
#endif
 * |--------------------------------------------------------------------------|
 * |    MSDU info   | MSDU 0 FW Desc    |         MSDU 0 Length               |
 * |--------------------------------------------------------------------------|
 * |                        MSDU 1 bus address (bits 31:0)                    |
#if HTT_PADDR64
 * |                        MSDU 1 bus address (bits 63:32)                   |
#endif
 * |--------------------------------------------------------------------------|
 * |    MSDU info   | MSDU 1 FW Desc    |         MSDU 1 Length               |
 * |--------------------------------------------------------------------------|
 */


/** @brief - MSDU info byte for TCP_CHECKSUM_OFFLOAD use
 *
 * @details
 *                            bits
 * |  7  | 6  |   5   |    4   |   3    |    2    |    1    |     0     |
 * |-----+----+-------+--------+--------+---------+---------+-----------|
 * | reserved | is IP | is UDP | is TCP | is IPv6 |IP chksum|  TCP/UDP  |
 * |          | frag  |        |        |         | fail    |chksum fail|
 * |-----+----+-------+--------+--------+---------+---------+-----------|
 * (see fw_rx_msdu_info def in wal_rx_desc.h)
 */

struct htt_rx_in_ord_paddr_ind_hdr_t
{
    A_UINT32 /* word 0 */
        msg_type:   8,
        ext_tid:    5,
        offload:    1,
        frag:       1,
        pktlog:     1, /* tell host whether to store MSDUs referenced in this message in pktlog */
        peer_id:    16;

    A_UINT32 /* word 1 */
        vap_id:     8,
        /* NOTE:
         * This reserved_1 field is not truly reserved - certain targets use
         * this field internally to store debug information, and do not zero
         * out the contents of the field before uploading the message to the
         * host.  Thus, any host-target communication supported by this field
         * is limited to using values that are never used by the debug
         * information stored by certain targets in the reserved_1 field.
         * In particular, the targets in question don't use the value 0x3
         * within bits 7:6 of this field (i.e. bits 15:14 of the A_UINT32),
         * so this previously-unused value within these bits is available to
         * use as the host / target PKT_CAPTURE_MODE flag.
         */
        reserved_1: 8, /* reserved_1a: 6, pkt_capture_mode: 2, */
                       /* if pkt_capture_mode == 0x3, host should
                        * send rx frames to monitor mode interface
                        */
        msdu_cnt:   16;
};

struct htt_rx_in_ord_paddr_ind_msdu32_t
{
    A_UINT32 dma_addr;
    A_UINT32
        length: 16,
        fw_desc: 8,
        msdu_info:8;
};
struct htt_rx_in_ord_paddr_ind_msdu64_t
{
    A_UINT32 dma_addr_lo;
    A_UINT32 dma_addr_hi;
    A_UINT32
        length: 16,
        fw_desc: 8,
        msdu_info:8;
};
#if HTT_PADDR64
    #define htt_rx_in_ord_paddr_ind_msdu_t htt_rx_in_ord_paddr_ind_msdu64_t
#else
    #define htt_rx_in_ord_paddr_ind_msdu_t htt_rx_in_ord_paddr_ind_msdu32_t
#endif


#define HTT_RX_IN_ORD_PADDR_IND_HDR_BYTES (sizeof(struct htt_rx_in_ord_paddr_ind_hdr_t))
#define HTT_RX_IN_ORD_PADDR_IND_HDR_DWORDS (HTT_RX_IN_ORD_PADDR_IND_HDR_BYTES >> 2)
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_BYTE_OFFSET  HTT_RX_IN_ORD_PADDR_IND_HDR_BYTES
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_DWORD_OFFSET HTT_RX_IN_ORD_PADDR_IND_HDR_DWORDS
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_BYTES_64 (sizeof(struct htt_rx_in_ord_paddr_ind_msdu64_t))
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_DWORDS_64 (HTT_RX_IN_ORD_PADDR_IND_MSDU_BYTES_64 >> 2)
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_BYTES_32 (sizeof(struct htt_rx_in_ord_paddr_ind_msdu32_t))
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_DWORDS_32 (HTT_RX_IN_ORD_PADDR_IND_MSDU_BYTES_32 >> 2)
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_BYTES (sizeof(struct htt_rx_in_ord_paddr_ind_msdu_t))
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_DWORDS (HTT_RX_IN_ORD_PADDR_IND_MSDU_BYTES >> 2)

#define HTT_RX_IN_ORD_PADDR_IND_EXT_TID_M      0x00001f00
#define HTT_RX_IN_ORD_PADDR_IND_EXT_TID_S      8
#define HTT_RX_IN_ORD_PADDR_IND_OFFLOAD_M      0x00002000
#define HTT_RX_IN_ORD_PADDR_IND_OFFLOAD_S      13
#define HTT_RX_IN_ORD_PADDR_IND_FRAG_M         0x00004000
#define HTT_RX_IN_ORD_PADDR_IND_FRAG_S         14
#define HTT_RX_IN_ORD_PADDR_IND_PKTLOG_M       0x00008000
#define HTT_RX_IN_ORD_PADDR_IND_PKTLOG_S       15
#define HTT_RX_IN_ORD_PADDR_IND_PEER_ID_M      0xffff0000
#define HTT_RX_IN_ORD_PADDR_IND_PEER_ID_S      16
#define HTT_RX_IN_ORD_PADDR_IND_VAP_ID_M       0x000000ff
#define HTT_RX_IN_ORD_PADDR_IND_VAP_ID_S       0
#define HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_M 0x0000c000
#define HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_S 14
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_CNT_M     0xffff0000
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_CNT_S     16
/* for systems using 64-bit format for bus addresses */
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_HI_M     0xffffffff
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_HI_S     0
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_LO_M     0xffffffff
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_LO_S     0
/* for systems using 32-bit format for bus addresses */
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_M        0xffffffff
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_S        0
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_LEN_M     0x0000ffff
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_LEN_S     0
#define HTT_RX_IN_ORD_PADDR_IND_FW_DESC_M      0x00ff0000
#define HTT_RX_IN_ORD_PADDR_IND_FW_DESC_S      16
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_INFO_M    0xff000000
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_INFO_S    24


#define HTT_RX_IN_ORD_PADDR_IND_EXT_TID_SET(word, value)                              \
    do {                                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_EXT_TID, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_EXT_TID_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_EXT_TID_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_EXT_TID_M) >> HTT_RX_IN_ORD_PADDR_IND_EXT_TID_S)

#define HTT_RX_IN_ORD_PADDR_IND_PEER_ID_SET(word, value)                              \
    do {                                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_PEER_ID, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_PEER_ID_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_PEER_ID_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_PEER_ID_M) >> HTT_RX_IN_ORD_PADDR_IND_PEER_ID_S)

#define HTT_RX_IN_ORD_PADDR_IND_VAP_ID_SET(word, value)                              \
    do {                                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_VAP_ID, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_VAP_ID_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_VAP_ID_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_VAP_ID_M) >> HTT_RX_IN_ORD_PADDR_IND_VAP_ID_S)

/*
 * If the PKT_CAPTURE_MODE flags value is MONITOR (0x3), the host should
 * deliver the rx frames to the monitor mode interface.
 * The HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_MONITOR_SET macro
 * sets the PKT_CAPTURE_MODE flags value to MONITOR, and the
 * HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_IS_MONITOR_SET macro
 * checks whether the PKT_CAPTURE_MODE flags value is MONITOR.
 */
#define HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_MONITOR 0x3
#define HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_MONITOR_SET(word) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE, HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_MONITOR); \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_S; \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_IS_MONITOR_SET(word) \
    ((((word) & HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_M) >> HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_S) == \
    HTT_RX_IN_ORD_PADDR_IND_PKT_CAPTURE_MODE_MONITOR)

#define HTT_RX_IN_ORD_PADDR_IND_MSDU_CNT_SET(word, value)                              \
    do {                                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_MSDU_CNT, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_MSDU_CNT_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_CNT_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_MSDU_CNT_M) >> HTT_RX_IN_ORD_PADDR_IND_MSDU_CNT_S)

/* for systems using 64-bit format for bus addresses */
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_HI_SET(word, value)                     \
    do {                                                                      \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_PADDR_HI, value);           \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_PADDR_HI_S;             \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_HI_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_PADDR_HI_M) >> HTT_RX_IN_ORD_PADDR_IND_PADDR_HI_S)
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_LO_SET(word, value)                     \
        do {                                                                  \
            HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_PADDR_LO, value);       \
            (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_PADDR_LO_S;         \
        } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_LO_GET(word) \
        (((word) & HTT_RX_IN_ORD_PADDR_IND_PADDR_LO_M) >> HTT_RX_IN_ORD_PADDR_IND_PADDR_LO_S)

/* for systems using 32-bit format for bus addresses */
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_SET(word, value)                        \
    do {                                                                      \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_PADDR, value);              \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_PADDR_S;                \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_PADDR_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_PADDR_M) >> HTT_RX_IN_ORD_PADDR_IND_PADDR_S)

#define HTT_RX_IN_ORD_PADDR_IND_MSDU_LEN_SET(word, value)                              \
    do {                                                                         \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_MSDU_LEN, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_MSDU_LEN_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_LEN_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_MSDU_LEN_M) >> HTT_RX_IN_ORD_PADDR_IND_MSDU_LEN_S)

#define HTT_RX_IN_ORD_PADDR_IND_FW_DESC_SET(word, value)                              \
    do {                                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_FW_DESC, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_FW_DESC_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_FW_DESC_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_FW_DESC_M) >> HTT_RX_IN_ORD_PADDR_IND_FW_DESC_S)

#define HTT_RX_IN_ORD_PADDR_IND_MSDU_INFO_SET(word, value)                              \
    do {                                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_MSDU_INFO, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_MSDU_INFO_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_MSDU_INFO_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_MSDU_INFO_M) >> HTT_RX_IN_ORD_PADDR_IND_MSDU_INFO_S)

#define HTT_RX_IN_ORD_PADDR_IND_OFFLOAD_SET(word, value)                              \
    do {                                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_IND_OFFLOAD, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_IND_OFFLOAD_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_OFFLOAD_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_OFFLOAD_M) >> HTT_RX_IN_ORD_PADDR_IND_OFFLOAD_S)

#define HTT_RX_IN_ORD_PADDR_IND_FRAG_SET(word, value)                              \
    do {                                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_IND_FRAG, value);                    \
        (word) |= (value)  << HTT_RX_IN_ORD_IND_FRAG_S;                      \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_FRAG_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_FRAG_M) >> HTT_RX_IN_ORD_PADDR_IND_FRAG_S)

#define HTT_RX_IN_ORD_PADDR_IND_PKTLOG_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_IN_ORD_PADDR_IND_PKTLOG, value); \
        (word) |= (value)  << HTT_RX_IN_ORD_PADDR_IND_PKTLOG_S; \
    } while (0)
#define HTT_RX_IN_ORD_PADDR_IND_PKTLOG_GET(word) \
    (((word) & HTT_RX_IN_ORD_PADDR_IND_PKTLOG_M) >> HTT_RX_IN_ORD_PADDR_IND_PKTLOG_S)


/* definitions used within target -> host rx indication message */

PREPACK struct htt_rx_ind_hdr_prefix_t
{
    A_UINT32 /* word 0 */
        msg_type:      8,
        ext_tid:       5,
        release_valid: 1,
        flush_valid:   1,
        reserved0:     1,
        peer_id:       16;

    A_UINT32 /* word 1 */
        flush_start_seq_num:   6,
        flush_end_seq_num:     6,
        release_start_seq_num: 6,
        release_end_seq_num:   6,
        num_mpdu_ranges:       8;
} POSTPACK;

#define HTT_RX_IND_HDR_PREFIX_BYTES (sizeof(struct htt_rx_ind_hdr_prefix_t))
#define HTT_RX_IND_HDR_PREFIX_SIZE32 (HTT_RX_IND_HDR_PREFIX_BYTES >> 2)

#define HTT_TGT_RSSI_INVALID 0x80

PREPACK struct htt_rx_ppdu_desc_t
{
    #define HTT_RX_IND_PPDU_OFFSET_WORD_RSSI_CMB              0
    #define HTT_RX_IND_PPDU_OFFSET_WORD_TIMESTAMP_SUBMICROSEC 0
    #define HTT_RX_IND_PPDU_OFFSET_WORD_PHY_ERR_CODE          0
    #define HTT_RX_IND_PPDU_OFFSET_WORD_PHY_ERR               0
    #define HTT_RX_IND_PPDU_OFFSET_WORD_LEGACY_RATE           0
    #define HTT_RX_IND_PPDU_OFFSET_WORD_LEGACY_RATE_SEL       0
    #define HTT_RX_IND_PPDU_OFFSET_WORD_END_VALID             0
    #define HTT_RX_IND_PPDU_OFFSET_WORD_START_VALID           0
    A_UINT32 /* word 0 */
        rssi_cmb: 8,
        timestamp_submicrosec: 8,
        phy_err_code: 8,
        phy_err: 1,
        legacy_rate: 4,
        legacy_rate_sel: 1,
        end_valid: 1,
        start_valid: 1;

    #define HTT_RX_IND_PPDU_OFFSET_WORD_RSSI0 1
    union {
        A_UINT32 /* word 1 */
            rssi0_pri20: 8,
            rssi0_ext20: 8,
            rssi0_ext40: 8,
            rssi0_ext80: 8;
       A_UINT32 rssi0; /* access all 20/40/80 per-bandwidth RSSIs together */
    } u0;

    #define HTT_RX_IND_PPDU_OFFSET_WORD_RSSI1 2
    union {
        A_UINT32 /* word 2 */
            rssi1_pri20: 8,
            rssi1_ext20: 8,
            rssi1_ext40: 8,
            rssi1_ext80: 8;
       A_UINT32 rssi1; /* access all 20/40/80 per-bandwidth RSSIs together */
    } u1;

    #define HTT_RX_IND_PPDU_OFFSET_WORD_RSSI2 3
    union {
        A_UINT32 /* word 3 */
            rssi2_pri20: 8,
            rssi2_ext20: 8,
            rssi2_ext40: 8,
            rssi2_ext80: 8;
       A_UINT32 rssi2; /* access all 20/40/80 per-bandwidth RSSIs together */
    } u2;

    #define HTT_RX_IND_PPDU_OFFSET_WORD_RSSI3 4
    union {
        A_UINT32 /* word 4 */
            rssi3_pri20: 8,
            rssi3_ext20: 8,
            rssi3_ext40: 8,
            rssi3_ext80: 8;
       A_UINT32 rssi3; /* access all 20/40/80 per-bandwidth RSSIs together */
    } u3;

    #define HTT_RX_IND_PPDU_OFFSET_WORD_TSF32 5
    A_UINT32 tsf32; /* word 5 */

    #define HTT_RX_IND_PPDU_OFFSET_WORD_TIMESTAMP_MICROSEC 6
    A_UINT32 timestamp_microsec; /* word 6 */

    #define HTT_RX_IND_PPDU_OFFSET_WORD_PREAMBLE_TYPE 7
    #define HTT_RX_IND_PPDU_OFFSET_WORD_VHT_SIG_A1    7
    A_UINT32 /* word 7 */
        vht_sig_a1: 24,
        preamble_type: 8;

    #define HTT_RX_IND_PPDU_OFFSET_WORD_VHT_SIG_A2    8
    #define HTT_RX_IND_PPDU_OFFSET_WORD_SA_ANT_MATRIX 8
    A_UINT32 /* word 8 */
        vht_sig_a2: 24,
        /* sa_ant_matrix
         * For cases where a single rx chain has options to be connected to
         * different rx antennas, show which rx antennas were in use during
         * receipt of a given PPDU.
         * This sa_ant_matrix provides a bitmask of the antennas used while
         * receiving this frame.
         */
        sa_ant_matrix: 8;
} POSTPACK;

#define HTT_RX_PPDU_DESC_BYTES (sizeof(struct htt_rx_ppdu_desc_t))
#define HTT_RX_PPDU_DESC_SIZE32 (HTT_RX_PPDU_DESC_BYTES >> 2)

PREPACK struct htt_rx_ind_hdr_suffix_t
{
    A_UINT32 /* word 0 */
        fw_rx_desc_bytes: 16,
        reserved0: 16;
} POSTPACK;

#define HTT_RX_IND_HDR_SUFFIX_BYTES (sizeof(struct htt_rx_ind_hdr_suffix_t))
#define HTT_RX_IND_HDR_SUFFIX_SIZE32 (HTT_RX_IND_HDR_SUFFIX_BYTES >> 2)

PREPACK struct htt_rx_ind_hdr_t
{
    struct htt_rx_ind_hdr_prefix_t prefix;
    struct htt_rx_ppdu_desc_t      rx_ppdu_desc;
    struct htt_rx_ind_hdr_suffix_t suffix;
} POSTPACK;

#define HTT_RX_IND_HDR_BYTES (sizeof(struct htt_rx_ind_hdr_t))
#define HTT_RX_IND_HDR_SIZE32 (HTT_RX_IND_HDR_BYTES >> 2)

/* confirm that HTT_RX_IND_HDR_BYTES is a multiple of 4 */
A_COMPILE_TIME_ASSERT(HTT_RX_IND_hdr_size_quantum,
    (HTT_RX_IND_HDR_BYTES & 0x3) == 0);

/*
 * HTT_RX_IND_FW_RX_PPDU_DESC_BYTE_OFFSET:
 * the offset into the HTT rx indication message at which the
 * FW rx PPDU descriptor resides
 */
#define HTT_RX_IND_FW_RX_PPDU_DESC_BYTE_OFFSET HTT_RX_IND_HDR_PREFIX_BYTES

/*
 * HTT_RX_IND_HDR_SUFFIX_BYTE_OFFSET:
 * the offset into the HTT rx indication message at which the
 * header suffix (FW rx MSDU byte count) resides
 */
#define HTT_RX_IND_HDR_SUFFIX_BYTE_OFFSET \
    (HTT_RX_IND_FW_RX_PPDU_DESC_BYTE_OFFSET + HTT_RX_PPDU_DESC_BYTES)

/*
 * HTT_RX_IND_FW_RX_DESC_BYTE_OFFSET:
 * the offset into the HTT rx indication message at which the per-MSDU
 * information starts
 * Bytes 0-7 are the message header; bytes 8-11 contain the length of the
 * per-MSDU information portion of the message.  The per-MSDU info itself
 * starts at byte 12.
 */
#define HTT_RX_IND_FW_RX_DESC_BYTE_OFFSET HTT_RX_IND_HDR_BYTES


/**
 * @brief target -> host rx indication message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_IND
 *
 * @details
 * The following field definitions describe the format of the rx indication
 * message sent from the target to the host.
 * The message consists of three major sections:
 * 1.  a fixed-length header
 * 2.  a variable-length list of firmware rx MSDU descriptors
 * 3.  one or more 4-octet MPDU range information elements
 * The fixed length header itself has two sub-sections
 * 1.  the message meta-information, including identification of the
 *     sender and type of the received data, and a 4-octet flush/release IE
 * 2.  the firmware rx PPDU descriptor
 *
 * The format of the message is depicted below.
 * in this depiction, the following abbreviations are used for information
 * elements within the message:
 *   - SV - start valid: this flag is set if the FW rx PPDU descriptor
 *          elements associated with the PPDU start are valid.
 *          Specifically, the following fields are valid only if SV is set:
 *              RSSI (all variants), L, legacy rate, preamble type, service,
 *              VHT-SIG-A
 *   - EV - end valid: this flag is set if the FW rx PPDU descriptor
 *          elements associated with the PPDU end are valid.
 *          Specifically, the following fields are valid only if EV is set:
 *              P, PHY err code, TSF, microsec / sub-microsec timestamp
 *   - L  - Legacy rate selector - if legacy rates are used, this flag
 *          indicates whether the rate is from a CCK (L == 1) or OFDM
 *          (L == 0) PHY.
 *   - P  - PHY error flag - boolean indication of whether the rx frame had
 *          a PHY error
 *
 * |31            24|23         18|17|16|15|14|13|12|11|10|9|8|7|6|5|4       0|
 * |----------------+-------------------+---------------------+---------------|
 * |                  peer ID           |  |RV|FV| ext TID    |   msg type    |
 * |--------------------------------------------------------------------------|
 * |      num       |   release   |     release     |    flush    |   flush   |
 * |      MPDU      |     end     |      start      |     end     |   start   |
 * |     ranges     |   seq num   |     seq num     |   seq num   |  seq num  |
 * |==========================================================================|
 * |S|E|L| legacy |P|   PHY err code    |     sub-microsec    |    combined   |
 * |V|V| |  rate  | |                   |       timestamp     |       RSSI    |
 * |--------------------------------------------------------------------------|
 * | RSSI rx0 ext80 |  RSSI rx0 ext40   |    RSSI rx0  ext20  | RSSI rx0 pri20|
 * |--------------------------------------------------------------------------|
 * | RSSI rx1 ext80 |  RSSI rx1 ext40   |    RSSI rx1  ext20  | RSSI rx1 pri20|
 * |--------------------------------------------------------------------------|
 * | RSSI rx2 ext80 |  RSSI rx2 ext40   |    RSSI rx2  ext20  | RSSI rx2 pri20|
 * |--------------------------------------------------------------------------|
 * | RSSI rx3 ext80 |  RSSI rx3 ext40   |    RSSI rx3  ext20  | RSSI rx3 pri20|
 * |--------------------------------------------------------------------------|
 * |                                  TSF LSBs                                |
 * |--------------------------------------------------------------------------|
 * |                             microsec timestamp                           |
 * |--------------------------------------------------------------------------|
 * | preamble type  |                    HT-SIG / VHT-SIG-A1                  |
 * |--------------------------------------------------------------------------|
 * |    service     |                    HT-SIG / VHT-SIG-A2                  |
 * |==========================================================================|
 * |             reserved               |          FW rx desc bytes           |
 * |--------------------------------------------------------------------------|
 * |     MSDU Rx    |      MSDU Rx      |        MSDU Rx      |    MSDU Rx    |
 * |     desc B3    |      desc B2      |        desc B1      |    desc B0    |
 * |--------------------------------------------------------------------------|
 * :                                    :                                     :
 * |--------------------------------------------------------------------------|
 * |                          alignment                       |    MSDU Rx    |
 * |                           padding                        |    desc Bn    |
 * |--------------------------------------------------------------------------|
 * |              reserved              |  MPDU range status  |   MPDU count  |
 * |--------------------------------------------------------------------------|
 * :              reserved              :  MPDU range status  :   MPDU count  :
 * :- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - :
 *
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx indication message
 *     Value: 0x1 (HTT_T2H_MSG_TYPE_RX_IND)
 *   - EXT_TID
 *     Bits 12:8
 *     Purpose: identify the traffic ID of the rx data, including
 *         special "extended" TID values for multicast, broadcast, and
 *         non-QoS data frames
 *     Value: 0-15 for regular TIDs, or >= 16 for bcast/mcast/non-QoS
 *   - FLUSH_VALID (FV)
 *     Bit 13
 *     Purpose: indicate whether the flush IE (start/end sequence numbers)
 *         is valid
 *     Value:
 *         1 -> flush IE is valid and needs to be processed
 *         0 -> flush IE is not valid and should be ignored
 *   - REL_VALID (RV)
 *     Bit 13
 *     Purpose: indicate whether the release IE (start/end sequence numbers)
 *         is valid
 *     Value:
 *         1 -> release IE is valid and needs to be processed
 *         0 -> release IE is not valid and should be ignored
 *   - PEER_ID
 *     Bits 31:16
 *     Purpose: Identify, by ID, which peer sent the rx data
 *     Value: ID of the peer who sent the rx data
 *   - FLUSH_SEQ_NUM_START
 *     Bits 5:0
 *     Purpose: Indicate the start of a series of MPDUs to flush
 *         Not all MPDUs within this series are necessarily valid - the host
 *         must check each sequence number within this range to see if the
 *         corresponding MPDU is actually present.
 *         This field is only valid if the FV bit is set.
 *     Value:
 *         The sequence number for the first MPDUs to check to flush.
 *         The sequence number is masked by 0x3f.
 *   - FLUSH_SEQ_NUM_END
 *     Bits 11:6
 *     Purpose: Indicate the end of a series of MPDUs to flush
 *     Value:
 *         The sequence number one larger than the sequence number of the
 *         last MPDU to check to flush.
 *         The sequence number is masked by 0x3f.
 *         Not all MPDUs within this series are necessarily valid - the host
 *         must check each sequence number within this range to see if the
 *         corresponding MPDU is actually present.
 *         This field is only valid if the FV bit is set.
 *   - REL_SEQ_NUM_START
 *     Bits 17:12
 *     Purpose: Indicate the start of a series of MPDUs to release.
 *         All MPDUs within this series are present and valid - the host
 *         need not check each sequence number within this range to see if
 *         the corresponding MPDU is actually present.
 *         This field is only valid if the RV bit is set.
 *     Value:
 *         The sequence number for the first MPDUs to check to release.
 *         The sequence number is masked by 0x3f.
 *   - REL_SEQ_NUM_END
 *     Bits 23:18
 *     Purpose: Indicate the end of a series of MPDUs to release.
 *     Value:
 *         The sequence number one larger than the sequence number of the
 *         last MPDU to check to release.
 *         The sequence number is masked by 0x3f.
 *         All MPDUs within this series are present and valid - the host
 *         need not check each sequence number within this range to see if
 *         the corresponding MPDU is actually present.
 *         This field is only valid if the RV bit is set.
 *   - NUM_MPDU_RANGES
 *     Bits 31:24
 *     Purpose: Indicate how many ranges of MPDUs are present.
 *         Each MPDU range consists of a series of contiguous MPDUs within the
 *         rx frame sequence which all have the same MPDU status.
 *     Value: 1-63 (typically a small number, like 1-3)
 *
 * Rx PPDU descriptor fields:
 *   - RSSI_CMB
 *     Bits 7:0
 *     Purpose: Combined RSSI from all active rx chains, across the active
 *         bandwidth.
 *     Value: RSSI dB units w.r.t. noise floor
 *   - TIMESTAMP_SUBMICROSEC
 *     Bits 15:8
 *     Purpose: high-resolution timestamp
 *     Value:
 *         Sub-microsecond time of PPDU reception.
 *         This timestamp ranges from [0,MAC clock MHz).
 *         This timestamp can be used in conjunction with TIMESTAMP_MICROSEC
 *         to form a high-resolution, large range rx timestamp.
 *   - PHY_ERR_CODE
 *     Bits 23:16
 *     Purpose:
 *         If the rx frame processing resulted in a PHY error, indicate what
 *         type of rx PHY error occurred.
 *     Value:
 *         This field is valid if the "P" (PHY_ERR) flag is set.
 *         TBD: document/specify the values for this field
 *   - PHY_ERR
 *     Bit 24
 *     Purpose: indicate whether the rx PPDU had a PHY error
 *     Value: 0 -> no rx PHY error, 1 -> rx PHY error encountered
 *   - LEGACY_RATE
 *     Bits 28:25
 *     Purpose:
 *         If the rx frame used a legacy rate rather than a HT or VHT rate,
 *         specify which rate was used.
 *     Value:
 *         The LEGACY_RATE field's value depends on the "L" (LEGACY_RATE_SEL)
 *         flag.
 *         If LEGACY_RATE_SEL is 0:
 *             0x8: OFDM 48 Mbps
 *             0x9: OFDM 24 Mbps
 *             0xA: OFDM 12 Mbps
 *             0xB: OFDM 6 Mbps
 *             0xC: OFDM 54 Mbps
 *             0xD: OFDM 36 Mbps
 *             0xE: OFDM 18 Mbps
 *             0xF: OFDM 9 Mbps
 *         If LEGACY_RATE_SEL is 1:
 *             0x8: CCK 11 Mbps long preamble
 *             0x9: CCK 5.5 Mbps long preamble
 *             0xA: CCK 2 Mbps long preamble
 *             0xB: CCK 1 Mbps long preamble
 *             0xC: CCK 11 Mbps short preamble
 *             0xD: CCK 5.5 Mbps short preamble
 *             0xE: CCK 2 Mbps short preamble
 *   - LEGACY_RATE_SEL
 *     Bit 29
 *     Purpose: if rx used a legacy rate, specify whether it was OFDM or CCK
 *     Value:
 *         This field is valid if the PREAMBLE_TYPE field indicates the rx
 *         used a legacy rate.
 *         0 -> OFDM, 1 -> CCK
 *   - END_VALID
 *     Bit 30
 *     Purpose: Indicate whether the FW rx PPDU desc fields associated with
 *         the start of the PPDU are valid.  Specifically, the following
 *         fields are only valid if END_VALID is set:
 *         PHY_ERR, PHY_ERR_CODE, TSF32, TIMESTAMP_MICROSEC,
 *         TIMESTAMP_SUBMICROSEC
 *     Value:
 *         0 -> rx PPDU desc end fields are not valid
 *         1 -> rx PPDU desc end fields are valid
 *   - START_VALID
 *     Bit 31
 *     Purpose: Indicate whether the FW rx PPDU desc fields associated with
 *         the end of the PPDU are valid.  Specifically, the following
 *         fields are only valid if START_VALID is set:
 *         RSSI, LEGACY_RATE_SEL, LEGACY_RATE, PREAMBLE_TYPE, SERVICE,
 *         VHT-SIG-A
 *     Value:
 *         0 -> rx PPDU desc start fields are not valid
 *         1 -> rx PPDU desc start fields are valid
 *   - RSSI0_PRI20
 *     Bits 7:0
 *     Purpose: RSSI from chain 0 on the primary 20 MHz channel
 *     Value: RSSI dB units w.r.t. noise floor
 *
 *   - RSSI0_EXT20
 *     Bits 7:0
 *     Purpose: RSSI from chain 0 on the bonded extension 20 MHz channel
 *         (if the rx bandwidth was >= 40 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI0_EXT40
 *     Bits 7:0
 *     Purpose: RSSI from chain 0 on the bonded extension 40 MHz channel
 *         (if the rx bandwidth was >= 80 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI0_EXT80
 *     Bits 7:0
 *     Purpose: RSSI from chain 0 on the bonded extension 80 MHz channel
 *         (if the rx bandwidth was >= 160 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *
 *   - RSSI1_PRI20
 *     Bits 7:0
 *     Purpose: RSSI from chain 1 on the primary 20 MHz channel
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI1_EXT20
 *     Bits 7:0
 *     Purpose: RSSI from chain 1 on the bonded extension 20 MHz channel
 *         (if the rx bandwidth was >= 40 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI1_EXT40
 *     Bits 7:0
 *     Purpose: RSSI from chain 1 on the bonded extension 40 MHz channel
 *         (if the rx bandwidth was >= 80 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI1_EXT80
 *     Bits 7:0
 *     Purpose: RSSI from chain 1 on the bonded extension 80 MHz channel
 *         (if the rx bandwidth was >= 160 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *
 *   - RSSI2_PRI20
 *     Bits 7:0
 *     Purpose: RSSI from chain 2 on the primary 20 MHz channel
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI2_EXT20
 *     Bits 7:0
 *     Purpose: RSSI from chain 2 on the bonded extension 20 MHz channel
 *         (if the rx bandwidth was >= 40 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI2_EXT40
 *     Bits 7:0
 *     Purpose: RSSI from chain 2 on the bonded extension 40 MHz channel
 *         (if the rx bandwidth was >= 80 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI2_EXT80
 *     Bits 7:0
 *     Purpose: RSSI from chain 2 on the bonded extension 80 MHz channel
 *         (if the rx bandwidth was >= 160 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *
 *   - RSSI3_PRI20
 *     Bits 7:0
 *     Purpose: RSSI from chain 3 on the primary 20 MHz channel
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI3_EXT20
 *     Bits 7:0
 *     Purpose: RSSI from chain 3 on the bonded extension 20 MHz channel
 *         (if the rx bandwidth was >= 40 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI3_EXT40
 *     Bits 7:0
 *     Purpose: RSSI from chain 3 on the bonded extension 40 MHz channel
 *         (if the rx bandwidth was >= 80 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *   - RSSI3_EXT80
 *     Bits 7:0
 *     Purpose: RSSI from chain 3 on the bonded extension 80 MHz channel
 *         (if the rx bandwidth was >= 160 MHz)
 *     Value: RSSI dB units w.r.t. noise floor
 *
 *   - TSF32
 *     Bits 31:0
 *     Purpose: specify the time the rx PPDU was received, in TSF units
 *     Value: 32 LSBs of the TSF
 *   - TIMESTAMP_MICROSEC
 *     Bits 31:0
 *     Purpose: specify the time the rx PPDU was received, in microsecond units
 *     Value: PPDU rx time, in microseconds
 *   - VHT_SIG_A1
 *     Bits 23:0
 *     Purpose: Provide the HT-SIG (initial 24 bits) or VHT-SIG-A1 field
 *         from the rx PPDU
 *     Value:
 *         If PREAMBLE_TYPE specifies VHT, then this field contains the
 *         VHT-SIG-A1 data.
 *         If PREAMBLE_TYPE specifies HT, then this field contains the
 *         first 24 bits of the HT-SIG data.
 *         Otherwise, this field is invalid.
 *         Refer to the the 802.11 protocol for the definition of the
 *         HT-SIG and VHT-SIG-A1 fields
 *   - VHT_SIG_A2
 *     Bits 23:0
 *     Purpose: Provide the HT-SIG (final 24 bits) or VHT-SIG-A2 field
 *         from the rx PPDU
 *     Value:
 *         If PREAMBLE_TYPE specifies VHT, then this field contains the
 *         VHT-SIG-A2 data.
 *         If PREAMBLE_TYPE specifies HT, then this field contains the
 *         last 24 bits of the HT-SIG data.
 *         Otherwise, this field is invalid.
 *         Refer to the the 802.11 protocol for the definition of the
 *         HT-SIG and VHT-SIG-A2 fields
 *   - PREAMBLE_TYPE
 *     Bits 31:24
 *     Purpose: indicate the PHY format of the received burst
 *     Value:
 *         0x4: Legacy (OFDM/CCK)
 *         0x8: HT
 *         0x9: HT with TxBF
 *         0xC: VHT
 *         0xD: VHT with TxBF
 *   - SERVICE
 *     Bits 31:24
 *     Purpose: TBD
 *     Value: TBD
 *
 * Rx MSDU descriptor fields:
 *   - FW_RX_DESC_BYTES
 *     Bits 15:0
 *     Purpose: Indicate how many bytes in the Rx indication are used for
 *         FW Rx descriptors
 *
 * Payload fields:
 *   - MPDU_COUNT
 *     Bits 7:0
 *     Purpose: Indicate how many sequential MPDUs share the same status.
 *         All MPDUs within the indicated list are from the same RA-TA-TID.
 *   - MPDU_STATUS
 *     Bits 15:8
 *     Purpose: Indicate whether the (group of sequential) MPDU(s) were
 *         received successfully.
 *     Value:
 *         0x1: success
 *         0x2: FCS error
 *         0x3: duplicate error
 *         0x4: replay error
 *         0x5: invalid peer
 */
/* header fields */
#define HTT_RX_IND_EXT_TID_M      0x1f00
#define HTT_RX_IND_EXT_TID_S      8
#define HTT_RX_IND_FLUSH_VALID_M  0x2000
#define HTT_RX_IND_FLUSH_VALID_S  13
#define HTT_RX_IND_REL_VALID_M    0x4000
#define HTT_RX_IND_REL_VALID_S    14
#define HTT_RX_IND_PEER_ID_M      0xffff0000
#define HTT_RX_IND_PEER_ID_S      16

#define HTT_RX_IND_FLUSH_SEQ_NUM_START_M 0x3f
#define HTT_RX_IND_FLUSH_SEQ_NUM_START_S 0
#define HTT_RX_IND_FLUSH_SEQ_NUM_END_M   0xfc0
#define HTT_RX_IND_FLUSH_SEQ_NUM_END_S   6
#define HTT_RX_IND_REL_SEQ_NUM_START_M   0x3f000
#define HTT_RX_IND_REL_SEQ_NUM_START_S   12
#define HTT_RX_IND_REL_SEQ_NUM_END_M     0xfc0000
#define HTT_RX_IND_REL_SEQ_NUM_END_S     18
#define HTT_RX_IND_NUM_MPDU_RANGES_M     0xff000000
#define HTT_RX_IND_NUM_MPDU_RANGES_S     24

/* rx PPDU descriptor fields */
#define HTT_RX_IND_RSSI_CMB_M              0x000000ff
#define HTT_RX_IND_RSSI_CMB_S              0
#define HTT_RX_IND_TIMESTAMP_SUBMICROSEC_M 0x0000ff00
#define HTT_RX_IND_TIMESTAMP_SUBMICROSEC_S 8
#define HTT_RX_IND_PHY_ERR_CODE_M          0x00ff0000
#define HTT_RX_IND_PHY_ERR_CODE_S          16
#define HTT_RX_IND_PHY_ERR_M               0x01000000
#define HTT_RX_IND_PHY_ERR_S               24
#define HTT_RX_IND_LEGACY_RATE_M           0x1e000000
#define HTT_RX_IND_LEGACY_RATE_S           25
#define HTT_RX_IND_LEGACY_RATE_SEL_M       0x20000000
#define HTT_RX_IND_LEGACY_RATE_SEL_S       29
#define HTT_RX_IND_END_VALID_M             0x40000000
#define HTT_RX_IND_END_VALID_S             30
#define HTT_RX_IND_START_VALID_M           0x80000000
#define HTT_RX_IND_START_VALID_S           31

#define HTT_RX_IND_RSSI_PRI20_M            0x000000ff
#define HTT_RX_IND_RSSI_PRI20_S            0
#define HTT_RX_IND_RSSI_EXT20_M            0x0000ff00
#define HTT_RX_IND_RSSI_EXT20_S            8
#define HTT_RX_IND_RSSI_EXT40_M            0x00ff0000
#define HTT_RX_IND_RSSI_EXT40_S            16
#define HTT_RX_IND_RSSI_EXT80_M            0xff000000
#define HTT_RX_IND_RSSI_EXT80_S            24

#define HTT_RX_IND_VHT_SIG_A1_M            0x00ffffff
#define HTT_RX_IND_VHT_SIG_A1_S            0
#define HTT_RX_IND_VHT_SIG_A2_M            0x00ffffff
#define HTT_RX_IND_VHT_SIG_A2_S            0
#define HTT_RX_IND_PREAMBLE_TYPE_M         0xff000000
#define HTT_RX_IND_PREAMBLE_TYPE_S         24
#define HTT_RX_IND_SERVICE_M               0xff000000
#define HTT_RX_IND_SERVICE_S               24
#define HTT_RX_IND_SA_ANT_MATRIX_M         0xff000000
#define HTT_RX_IND_SA_ANT_MATRIX_S         24

/* rx MSDU descriptor fields */
#define HTT_RX_IND_FW_RX_DESC_BYTES_M   0xffff
#define HTT_RX_IND_FW_RX_DESC_BYTES_S   0

/* payload fields */
#define HTT_RX_IND_MPDU_COUNT_M    0xff
#define HTT_RX_IND_MPDU_COUNT_S    0
#define HTT_RX_IND_MPDU_STATUS_M   0xff00
#define HTT_RX_IND_MPDU_STATUS_S   8


#define HTT_RX_IND_EXT_TID_SET(word, value)                              \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_EXT_TID, value);                    \
        (word) |= (value)  << HTT_RX_IND_EXT_TID_S;                      \
    } while (0)
#define HTT_RX_IND_EXT_TID_GET(word) \
    (((word) & HTT_RX_IND_EXT_TID_M) >> HTT_RX_IND_EXT_TID_S)

#define HTT_RX_IND_FLUSH_VALID_SET(word, value)                          \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_FLUSH_VALID, value);                \
        (word) |= (value)  << HTT_RX_IND_FLUSH_VALID_S;                  \
    } while (0)
#define HTT_RX_IND_FLUSH_VALID_GET(word) \
    (((word) & HTT_RX_IND_FLUSH_VALID_M) >> HTT_RX_IND_FLUSH_VALID_S)

#define HTT_RX_IND_REL_VALID_SET(word, value)                            \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_REL_VALID, value);                  \
        (word) |= (value)  << HTT_RX_IND_REL_VALID_S;                    \
    } while (0)
#define HTT_RX_IND_REL_VALID_GET(word) \
    (((word) & HTT_RX_IND_REL_VALID_M) >> HTT_RX_IND_REL_VALID_S)

#define HTT_RX_IND_PEER_ID_SET(word, value)                              \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_PEER_ID, value);                    \
        (word) |= (value)  << HTT_RX_IND_PEER_ID_S;                      \
    } while (0)
#define HTT_RX_IND_PEER_ID_GET(word) \
    (((word) & HTT_RX_IND_PEER_ID_M) >> HTT_RX_IND_PEER_ID_S)


#define HTT_RX_IND_FW_RX_DESC_BYTES_SET(word, value)                     \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_FW_RX_DESC_BYTES, value);           \
        (word) |= (value)  << HTT_RX_IND_FW_RX_DESC_BYTES_S;             \
    } while (0)
#define HTT_RX_IND_FW_RX_DESC_BYTES_GET(word) \
    (((word) & HTT_RX_IND_FW_RX_DESC_BYTES_M) >> HTT_RX_IND_FW_RX_DESC_BYTES_S)


#define HTT_RX_IND_FLUSH_SEQ_NUM_START_SET(word, value)              \
    do {                                                             \
        HTT_CHECK_SET_VAL(HTT_RX_IND_FLUSH_SEQ_NUM_START, value);    \
        (word) |= (value)  << HTT_RX_IND_FLUSH_SEQ_NUM_START_S;      \
    } while (0)
#define HTT_RX_IND_FLUSH_SEQ_NUM_START_GET(word)                     \
     (((word) & HTT_RX_IND_FLUSH_SEQ_NUM_START_M) >>                 \
      HTT_RX_IND_FLUSH_SEQ_NUM_START_S)

#define HTT_RX_IND_FLUSH_SEQ_NUM_END_SET(word, value)                \
    do {                                                             \
        HTT_CHECK_SET_VAL(HTT_RX_IND_FLUSH_SEQ_NUM_END, value);      \
        (word) |= (value)  << HTT_RX_IND_FLUSH_SEQ_NUM_END_S;        \
    } while (0)
#define HTT_RX_IND_FLUSH_SEQ_NUM_END_GET(word)                       \
    (((word) & HTT_RX_IND_FLUSH_SEQ_NUM_END_M) >>                    \
    HTT_RX_IND_FLUSH_SEQ_NUM_END_S)

#define HTT_RX_IND_REL_SEQ_NUM_START_SET(word, value)                \
    do {                                                             \
        HTT_CHECK_SET_VAL(HTT_RX_IND_REL_SEQ_NUM_START, value);      \
        (word) |= (value)  << HTT_RX_IND_REL_SEQ_NUM_START_S;        \
    } while (0)
#define HTT_RX_IND_REL_SEQ_NUM_START_GET(word)                       \
     (((word) & HTT_RX_IND_REL_SEQ_NUM_START_M) >>                   \
      HTT_RX_IND_REL_SEQ_NUM_START_S)

#define HTT_RX_IND_REL_SEQ_NUM_END_SET(word, value)                  \
    do {                                                             \
        HTT_CHECK_SET_VAL(HTT_RX_IND_REL_SEQ_NUM_END, value);        \
        (word) |= (value)  << HTT_RX_IND_REL_SEQ_NUM_END_S;          \
    } while (0)
#define HTT_RX_IND_REL_SEQ_NUM_END_GET(word)                         \
    (((word) & HTT_RX_IND_REL_SEQ_NUM_END_M) >>                      \
    HTT_RX_IND_REL_SEQ_NUM_END_S)

#define HTT_RX_IND_NUM_MPDU_RANGES_SET(word, value)                  \
    do {                                                             \
        HTT_CHECK_SET_VAL(HTT_RX_IND_NUM_MPDU_RANGES, value);        \
        (word) |= (value)  << HTT_RX_IND_NUM_MPDU_RANGES_S;          \
    } while (0)
#define HTT_RX_IND_NUM_MPDU_RANGES_GET(word)                         \
    (((word) & HTT_RX_IND_NUM_MPDU_RANGES_M) >>                      \
    HTT_RX_IND_NUM_MPDU_RANGES_S)

/* FW rx PPDU descriptor fields */
#define HTT_RX_IND_RSSI_CMB_SET(word, value)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_RX_IND_RSSI_CMB, value); \
        (word) |= (value)  << HTT_RX_IND_RSSI_CMB_S;   \
    } while (0)
#define HTT_RX_IND_RSSI_CMB_GET(word)    \
    (((word) & HTT_RX_IND_RSSI_CMB_M) >> \
    HTT_RX_IND_RSSI_CMB_S)

#define HTT_RX_IND_TIMESTAMP_SUBMICROSEC_SET(word, value)           \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_RX_IND_TIMESTAMP_SUBMICROSEC, value); \
        (word) |= (value)  << HTT_RX_IND_TIMESTAMP_SUBMICROSEC_S;   \
    } while (0)
#define HTT_RX_IND_TIMESTAMP_SUBMICROSEC_GET(word)    \
    (((word) & HTT_RX_IND_TIMESTAMP_SUBMICROSEC_M) >> \
    HTT_RX_IND_TIMESTAMP_SUBMICROSEC_S)

#define HTT_RX_IND_PHY_ERR_CODE_SET(word, value)           \
    do {                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_IND_PHY_ERR_CODE, value); \
        (word) |= (value)  << HTT_RX_IND_PHY_ERR_CODE_S;   \
    } while (0)
#define HTT_RX_IND_PHY_ERR_CODE_GET(word)    \
    (((word) & HTT_RX_IND_PHY_ERR_CODE_M) >> \
    HTT_RX_IND_PHY_ERR_CODE_S)

#define HTT_RX_IND_PHY_ERR_SET(word, value)           \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_RX_IND_PHY_ERR, value); \
        (word) |= (value)  << HTT_RX_IND_PHY_ERR_S;   \
    } while (0)
#define HTT_RX_IND_PHY_ERR_GET(word)    \
    (((word) & HTT_RX_IND_PHY_ERR_M) >> \
    HTT_RX_IND_PHY_ERR_S)

#define HTT_RX_IND_LEGACY_RATE_SET(word, value)           \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_IND_LEGACY_RATE, value); \
        (word) |= (value)  << HTT_RX_IND_LEGACY_RATE_S;   \
    } while (0)
#define HTT_RX_IND_LEGACY_RATE_GET(word)    \
    (((word) & HTT_RX_IND_LEGACY_RATE_M) >> \
    HTT_RX_IND_LEGACY_RATE_S)

#define HTT_RX_IND_LEGACY_RATE_SEL_SET(word, value)           \
    do {                                                           \
        HTT_CHECK_SET_VAL(HTT_RX_IND_LEGACY_RATE_SEL, value); \
        (word) |= (value)  << HTT_RX_IND_LEGACY_RATE_SEL_S;   \
    } while (0)
#define HTT_RX_IND_LEGACY_RATE_SEL_GET(word)    \
    (((word) & HTT_RX_IND_LEGACY_RATE_SEL_M) >> \
    HTT_RX_IND_LEGACY_RATE_SEL_S)

#define HTT_RX_IND_END_VALID_SET(word, value)           \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_IND_END_VALID, value); \
        (word) |= (value)  << HTT_RX_IND_END_VALID_S;   \
    } while (0)
#define HTT_RX_IND_END_VALID_GET(word)    \
    (((word) & HTT_RX_IND_END_VALID_M) >> \
    HTT_RX_IND_END_VALID_S)

#define HTT_RX_IND_START_VALID_SET(word, value)           \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_IND_START_VALID, value); \
        (word) |= (value)  << HTT_RX_IND_START_VALID_S;   \
    } while (0)
#define HTT_RX_IND_START_VALID_GET(word)    \
    (((word) & HTT_RX_IND_START_VALID_M) >> \
    HTT_RX_IND_START_VALID_S)

#define HTT_RX_IND_RSSI_PRI20_SET(word, value)           \
    do {                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_RSSI_PRI20, value); \
        (word) |= (value)  << HTT_RX_IND_RSSI_PRI20_S;   \
    } while (0)
#define HTT_RX_IND_RSSI_PRI20_GET(word)    \
    (((word) & HTT_RX_IND_RSSI_PRI20_M) >> \
    HTT_RX_IND_RSSI_PRI20_S)

#define HTT_RX_IND_RSSI_EXT20_SET(word, value)           \
    do {                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_RSSI_EXT20, value); \
        (word) |= (value)  << HTT_RX_IND_RSSI_EXT20_S;   \
    } while (0)
#define HTT_RX_IND_RSSI_EXT20_GET(word)    \
    (((word) & HTT_RX_IND_RSSI_EXT20_M) >> \
    HTT_RX_IND_RSSI_EXT20_S)

#define HTT_RX_IND_RSSI_EXT40_SET(word, value)           \
    do {                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_RSSI_EXT40, value); \
        (word) |= (value)  << HTT_RX_IND_RSSI_EXT40_S;   \
    } while (0)
#define HTT_RX_IND_RSSI_EXT40_GET(word)    \
    (((word) & HTT_RX_IND_RSSI_EXT40_M) >> \
    HTT_RX_IND_RSSI_EXT40_S)

#define HTT_RX_IND_RSSI_EXT80_SET(word, value)           \
    do {                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_RSSI_EXT80, value); \
        (word) |= (value)  << HTT_RX_IND_RSSI_EXT80_S;   \
    } while (0)
#define HTT_RX_IND_RSSI_EXT80_GET(word)    \
    (((word) & HTT_RX_IND_RSSI_EXT80_M) >> \
    HTT_RX_IND_RSSI_EXT80_S)

#define HTT_RX_IND_VHT_SIG_A1_SET(word, value)           \
    do {                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_VHT_SIG_A1, value); \
        (word) |= (value)  << HTT_RX_IND_VHT_SIG_A1_S;   \
    } while (0)
#define HTT_RX_IND_VHT_SIG_A1_GET(word)    \
    (((word) & HTT_RX_IND_VHT_SIG_A1_M) >> \
    HTT_RX_IND_VHT_SIG_A1_S)

#define HTT_RX_IND_VHT_SIG_A2_SET(word, value)           \
    do {                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_IND_VHT_SIG_A2, value); \
        (word) |= (value)  << HTT_RX_IND_VHT_SIG_A2_S;   \
    } while (0)
#define HTT_RX_IND_VHT_SIG_A2_GET(word)    \
    (((word) & HTT_RX_IND_VHT_SIG_A2_M) >> \
    HTT_RX_IND_VHT_SIG_A2_S)

#define HTT_RX_IND_PREAMBLE_TYPE_SET(word, value)           \
    do {                                                    \
        HTT_CHECK_SET_VAL(HTT_RX_IND_PREAMBLE_TYPE, value); \
        (word) |= (value)  << HTT_RX_IND_PREAMBLE_TYPE_S;   \
    } while (0)
#define HTT_RX_IND_PREAMBLE_TYPE_GET(word)    \
    (((word) & HTT_RX_IND_PREAMBLE_TYPE_M) >> \
    HTT_RX_IND_PREAMBLE_TYPE_S)

#define HTT_RX_IND_SERVICE_SET(word, value)           \
    do {                                              \
        HTT_CHECK_SET_VAL(HTT_RX_IND_SERVICE, value); \
        (word) |= (value)  << HTT_RX_IND_SERVICE_S;   \
    } while (0)
#define HTT_RX_IND_SERVICE_GET(word)    \
    (((word) & HTT_RX_IND_SERVICE_M) >> \
    HTT_RX_IND_SERVICE_S)

#define HTT_RX_IND_SA_ANT_MATRIX_SET(word, value)           \
    do {                                                    \
        HTT_CHECK_SET_VAL(HTT_RX_IND_SA_ANT_MATRIX, value); \
        (word) |= (value)  << HTT_RX_IND_SA_ANT_MATRIX_S;   \
    } while (0)
#define HTT_RX_IND_SA_ANT_MATRIX_GET(word)    \
    (((word) & HTT_RX_IND_SA_ANT_MATRIX_M) >> \
    HTT_RX_IND_SA_ANT_MATRIX_S)

#define HTT_RX_IND_MPDU_COUNT_SET(word, value)                          \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_IND_MPDU_COUNT, value);                \
        (word) |= (value)  << HTT_RX_IND_MPDU_COUNT_S;                  \
    } while (0)
#define HTT_RX_IND_MPDU_COUNT_GET(word) \
    (((word) & HTT_RX_IND_MPDU_COUNT_M) >> HTT_RX_IND_MPDU_COUNT_S)

#define HTT_RX_IND_MPDU_STATUS_SET(word, value)                         \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_IND_MPDU_STATUS, value);               \
        (word) |= (value)  << HTT_RX_IND_MPDU_STATUS_S;                 \
    } while (0)
#define HTT_RX_IND_MPDU_STATUS_GET(word) \
    (((word) & HTT_RX_IND_MPDU_STATUS_M) >> HTT_RX_IND_MPDU_STATUS_S)


#define HTT_RX_IND_HL_BYTES                               \
    (HTT_RX_IND_HDR_BYTES +                               \
     4 /* single FW rx MSDU descriptor */ + \
     4 /* single MPDU range information element */)
#define HTT_RX_IND_HL_SIZE32 (HTT_RX_IND_HL_BYTES >> 2)

/* Could we use one macro entry? */
#define HTT_WORD_SET(word, field, value) \
    do { \
        HTT_CHECK_SET_VAL(field, value); \
        (word) |= ((value) << field ## _S); \
    } while (0)
#define HTT_WORD_GET(word, field) \
    (((word) & field ## _M) >> field ## _S)

PREPACK struct hl_htt_rx_ind_base {
    A_UINT32 rx_ind_msg[HTT_RX_IND_HL_SIZE32];    /* align with LL case rx indication message, but reduced to 5 words */
} POSTPACK;

/*
 * HTT_RX_IND_HL_RX_DESC_BASE_OFFSET
 * Currently, we use a resv field in hl_htt_rx_ind_base to store some
 * HL host needed info; refer to fw_rx_desc_base in wal_rx_desc.h.
 * The field is just after the MSDU FW rx desc, and 1 byte ahead of
 * htt_rx_ind_hl_rx_desc_t.
 */
#define HTT_RX_IND_HL_RX_DESC_BASE_OFFSET (HTT_RX_IND_FW_RX_DESC_BYTE_OFFSET + 1)
struct htt_rx_ind_hl_rx_desc_t {
    A_UINT8 ver;
    A_UINT8 len;
    struct {
        A_UINT8
            first_msdu: 1,
            last_msdu: 1,
            c3_failed: 1,
            c4_failed: 1,
            ipv6: 1,
            tcp: 1,
            udp: 1,
            reserved: 1;
    } flags;
    /* NOTE: no reserved space - don't append any new fields here */
};

#define HTT_RX_IND_HL_RX_DESC_VER_OFFSET \
    (HTT_RX_IND_HL_RX_DESC_BASE_OFFSET \
     + offsetof(struct htt_rx_ind_hl_rx_desc_t, ver))
#define HTT_RX_IND_HL_RX_DESC_VER 0

#define HTT_RX_IND_HL_RX_DESC_LEN_OFFSET \
    (HTT_RX_IND_HL_RX_DESC_BASE_OFFSET \
     + offsetof(struct htt_rx_ind_hl_rx_desc_t, len))

#define HTT_RX_IND_HL_FLAG_OFFSET \
    (HTT_RX_IND_HL_RX_DESC_BASE_OFFSET \
     + offsetof(struct htt_rx_ind_hl_rx_desc_t, flags))

#define HTT_RX_IND_HL_FLAG_FIRST_MSDU   (0x01 << 0)
#define HTT_RX_IND_HL_FLAG_LAST_MSDU    (0x01 << 1)
#define HTT_RX_IND_HL_FLAG_C3_FAILED    (0x01 << 2) /* L3 checksum failed */
#define HTT_RX_IND_HL_FLAG_C4_FAILED    (0x01 << 3) /* L4 checksum failed */
#define HTT_RX_IND_HL_FLAG_IPV6         (0x01 << 4) /* is ipv6, or else ipv4 */
#define HTT_RX_IND_HL_FLAG_TCP          (0x01 << 5) /* is tcp */
#define HTT_RX_IND_HL_FLAG_UDP          (0x01 << 6) /* is udp */
/* This structure is used in HL, the basic descriptor information
 * used by host. the structure is translated by FW from HW desc
 * or generated by FW. But in HL monitor mode, the host would use
 * the same structure with LL.
 */
PREPACK struct hl_htt_rx_desc_base {
    A_UINT32
        seq_num:12,
        encrypted:1,
        chan_info_present:1,
        resv0:2,
        mcast_bcast:1,
        fragment:1,
        key_id_oct:8,
        resv1:6;
    A_UINT32
        pn_31_0;
    union {
        struct {
            A_UINT16 pn_47_32;
            A_UINT16 pn_63_48;
        } pn16;
        A_UINT32 pn_63_32;
    } u0;
    A_UINT32
        pn_95_64;
    A_UINT32
        pn_127_96;
} POSTPACK;


/*
 * Channel information can optionally be appended after hl_htt_rx_desc_base.
 * If so, the len field in htt_rx_ind_hl_rx_desc_t will be updated accordingly,
 * and the chan_info_present flag in hl_htt_rx_desc_base will be set.
 * Please see htt_chan_change_t for description of the fields.
 */
PREPACK struct htt_chan_info_t
{
    A_UINT32    primary_chan_center_freq_mhz: 16,
                contig_chan1_center_freq_mhz: 16;
    A_UINT32    contig_chan2_center_freq_mhz: 16,
                phy_mode: 8,
                reserved: 8;
} POSTPACK;

#define HTT_CHAN_INFO_SIZE      sizeof(struct htt_chan_info_t)

#define HL_RX_DESC_SIZE         (sizeof(struct hl_htt_rx_desc_base))
#define HL_RX_DESC_SIZE_DWORD   (HL_RX_STD_DESC_SIZE >> 2)

#define HTT_HL_RX_DESC_MPDU_SEQ_NUM_M       0xfff
#define HTT_HL_RX_DESC_MPDU_SEQ_NUM_S       0
#define HTT_HL_RX_DESC_MPDU_ENC_M           0x1000
#define HTT_HL_RX_DESC_MPDU_ENC_S           12
#define HTT_HL_RX_DESC_CHAN_INFO_PRESENT_M  0x2000
#define HTT_HL_RX_DESC_CHAN_INFO_PRESENT_S  13
#define HTT_HL_RX_DESC_MCAST_BCAST_M        0x10000
#define HTT_HL_RX_DESC_MCAST_BCAST_S        16
#define HTT_HL_RX_DESC_FRAGMENT_M           0x20000
#define HTT_HL_RX_DESC_FRAGMENT_S           17
#define HTT_HL_RX_DESC_KEY_ID_OCT_M         0x3fc0000
#define HTT_HL_RX_DESC_KEY_ID_OCT_S         18

#define HTT_HL_RX_DESC_PN_OFFSET            offsetof(struct hl_htt_rx_desc_base, pn_31_0)
#define HTT_HL_RX_DESC_PN_WORD_OFFSET       (HTT_HL_RX_DESC_PN_OFFSET >> 2)


/* Channel information */
#define HTT_CHAN_INFO_PRIMARY_CHAN_CENTER_FREQ_M   0x0000ffff
#define HTT_CHAN_INFO_PRIMARY_CHAN_CENTER_FREQ_S   0
#define HTT_CHAN_INFO_CONTIG_CHAN1_CENTER_FREQ_M   0xffff0000
#define HTT_CHAN_INFO_CONTIG_CHAN1_CENTER_FREQ_S   16
#define HTT_CHAN_INFO_CONTIG_CHAN2_CENTER_FREQ_M   0x0000ffff
#define HTT_CHAN_INFO_CONTIG_CHAN2_CENTER_FREQ_S   0
#define HTT_CHAN_INFO_PHY_MODE_M                   0x00ff0000
#define HTT_CHAN_INFO_PHY_MODE_S                   16


#define HTT_CHAN_INFO_PRIMARY_CHAN_CENTER_FREQ_SET(word, value)            \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_CHAN_INFO_PRIMARY_CHAN_CENTER_FREQ, value);  \
        (word) |= (value)  << HTT_CHAN_INFO_PRIMARY_CHAN_CENTER_FREQ_S;    \
    } while (0)
#define HTT_CHAN_INFO_PRIMARY_CHAN_CENTER_FREQ_GET(word)                   \
    (((word) & HTT_CHAN_INFO_PRIMARY_CHAN_CENTER_FREQ_M) >> HTT_CHAN_INFO_PRIMARY_CHAN_CENTER_FREQ_S)


#define HTT_CHAN_INFO_CONTIG_CHAN1_CENTER_FREQ_SET(word, value)            \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_CHAN_INFO_CONTIG_CHAN1_CENTER_FREQ, value);  \
        (word) |= (value)  << HTT_CHAN_INFO_CONTIG_CHAN1_CENTER_FREQ_S;    \
    } while (0)
#define HTT_CHAN_INFO_CONTIG_CHAN1_CENTER_FREQ_GET(word)                   \
    (((word) & HTT_CHAN_INFO_CONTIG_CHAN1_CENTER_FREQ_M) >> HTT_CHAN_INFO_CONTIG_CHAN1_CENTER_FREQ_S)


#define HTT_CHAN_INFO_CONTIG_CHAN2_CENTER_FREQ_SET(word, value)            \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_CHAN_INFO_CONTIG_CHAN2_CENTER_FREQ, value);  \
        (word) |= (value)  << HTT_CHAN_INFO_CONTIG_CHAN2_CENTER_FREQ_S;    \
    } while (0)
#define HTT_CHAN_INFO_CONTIG_CHAN2_CENTER_FREQ_GET(word)                   \
    (((word) & HTT_CHAN_INFO_CONTIG_CHAN2_CENTER_FREQ_M) >> HTT_CHAN_INFO_CONTIG_CHAN2_CENTER_FREQ_S)


#define HTT_CHAN_INFO_PHY_MODE_SET(word, value)            \
    do {                                                \
        HTT_CHECK_SET_VAL(HTT_CHAN_INFO_PHY_MODE, value);  \
        (word) |= (value)  << HTT_CHAN_INFO_PHY_MODE_S;    \
    } while (0)
#define HTT_CHAN_INFO_PHY_MODE_GET(word)                   \
    (((word) & HTT_CHAN_INFO_PHY_MODE_M) >> HTT_CHAN_INFO_PHY_MODE_S)

/*
 * @brief target -> host message definition for FW offloaded pkts
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_TX_OFFLOAD_DELIVER_IND
 *
 * @details
 * The following field definitions describe the format of the firmware
 * offload deliver message sent from the target to the host.
 *
 * definition for struct htt_tx_offload_deliver_ind_hdr_t
 *
 * |31                        20|19    16|15 13|12            8|7   5|4|3|2  0|
 * |----------------------------+--------+-----+---------------+-----+-+-+----|
 * |              reserved_1                                   |   msg type   |
 * |--------------------------------------------------------------------------|
 * |                            phy_timestamp_l32                             |
 * |--------------------------------------------------------------------------|
 * |                            WORD2 (see below)                             |
 * |--------------------------------------------------------------------------|
 * |          seqno                      |            framectrl               |
 * |--------------------------------------------------------------------------|
 * |                 reserved_3                |       vdev_id       | tid_num|
 * |--------------------------------------------------------------------------|
 * |       reserved_4           |       tx_mpdu_bytes                  |F|STAT|
 * |--------------------------------------------------------------------------|
 *
 * where:
 *     STAT = status
 *     F = format (802.3 vs. 802.11)
 *
 * definition for word 2
 *
 * |31    26|25| 24 |23 | 22 |21 19|18 17|16                  9|8  6|5   2|1 0|
 * |--------+--+----+---+----+-----+-----+---------------------+----+-----+---|
 * |reserv_2|BF|LDPC|SGI|STBC|  BW | NSS |        RSSI         |RATE| MCS |PR |
 * |--------------------------------------------------------------------------|
 *
 * where:
 *     PR = preamble
 *     BF = beamformed
 */

PREPACK struct htt_tx_offload_deliver_ind_hdr_t
{
    A_UINT32 /* word 0 */
            msg_type:8,    /* [ 7: 0] */
            reserved_1:24; /* [31: 8] */
    A_UINT32 phy_timestamp_l32; /* word 1 [31:0] */
    A_UINT32  /* word 2 */
        /* preamble:
         * 0-OFDM,
         * 1-CCk,
         * 2-HT,
         * 3-VHT
         */
        preamble: 2, /* [1:0] */
        /* mcs:
         * In case of HT preamble interpret
         * MCS along with NSS.
         * Valid values for HT are 0 to 7.
         * HT mcs 0 with NSS 2 is mcs 8.
         * Valid values for VHT are 0 to 9.
         */
        mcs:      4, /* [5:2] */
        /* rate:
         * This is applicable only for
         * CCK and OFDM preamble type
         * rate 0: OFDM 48 Mbps,
         *      1: OFDM 24 Mbps,
         *      2: OFDM 12 Mbps
         *      3: OFDM 6  Mbps
         *      4: OFDM 54 Mbps
         *      5: OFDM 36 Mbps
         *      6: OFDM 18 Mbps
         *      7: OFDM 9  Mbps
         * rate 0: CCK 11 Mbps Long
         *      1: CCK 5.5 Mbps Long
         *      2: CCK 2 Mbps Long
         *      3: CCK 1 Mbps Long
         *      4: CCK 11 Mbps Short
         *      5: CCK 5.5 Mbps Short
         *      6: CCK 2 Mbps Short
         */
        rate    : 3, /* [ 8: 6] */
        rssi    : 8, /* [16: 9] units=dBm */
        nss     : 2, /* [18:17] if nss 1 means 1ss and 2 means 2ss */
        bw      : 3, /* [21:19] (0=>20MHz, 1=>40MHz, 2=>80MHz, 3=>160MHz) */
        stbc    : 1, /* [22] */
        sgi     : 1, /* [23] */
        ldpc    : 1, /* [24] */
        beamformed: 1, /* [25] */
        reserved_2: 6; /* [31:26] */
    A_UINT32 /* word 3 */
        framectrl:16, /* [15: 0] */
        seqno:16;     /* [31:16] */
    A_UINT32 /* word 4 */
        tid_num:5, /* [ 4: 0] actual TID number */
        vdev_id:8, /* [12: 5] */
        reserved_3:19; /* [31:13] */
    A_UINT32 /* word 5 */
        /* status:
         *     0: tx_ok
         *     1: retry
         *     2: drop
         *     3: filtered
         *     4: abort
         *     5: tid delete
         *     6: sw abort
         *     7: dropped by peer migration
         */
        status:3, /* [2:0] */
        format:1, /* [3] 0: 802.3 format, 1: 802.11 format */
        tx_mpdu_bytes:16, /* [19:4] */
        /* Indicates retry count of offloaded/local generated Data tx frames */
        tx_retry_cnt:6, /* [25:20] */
        reserved_4:6; /* [31:26] */
} POSTPACK;

/* FW offload deliver ind message header fields */

/* DWORD one */
#define HTT_FW_OFFLOAD_IND_PHY_TIMESTAMP_L32_M  0xffffffff
#define HTT_FW_OFFLOAD_IND_PHY_TIMESTAMP_L32_S  0

/* DWORD two */
#define HTT_FW_OFFLOAD_IND_PREAMBLE_M           0x00000003
#define HTT_FW_OFFLOAD_IND_PREAMBLE_S           0
#define HTT_FW_OFFLOAD_IND_MCS_M                0x0000003c
#define HTT_FW_OFFLOAD_IND_MCS_S                2
#define HTT_FW_OFFLOAD_IND_RATE_M               0x000001c0
#define HTT_FW_OFFLOAD_IND_RATE_S               6
#define HTT_FW_OFFLOAD_IND_RSSI_M               0x0001fe00
#define HTT_FW_OFFLOAD_IND_RSSI_S               9
#define HTT_FW_OFFLOAD_IND_NSS_M                0x00060000
#define HTT_FW_OFFLOAD_IND_NSS_S                17
#define HTT_FW_OFFLOAD_IND_BW_M                 0x00380000
#define HTT_FW_OFFLOAD_IND_BW_S                 19
#define HTT_FW_OFFLOAD_IND_STBC_M               0x00400000
#define HTT_FW_OFFLOAD_IND_STBC_S               22
#define HTT_FW_OFFLOAD_IND_SGI_M                0x00800000
#define HTT_FW_OFFLOAD_IND_SGI_S                23
#define HTT_FW_OFFLOAD_IND_LDPC_M               0x01000000
#define HTT_FW_OFFLOAD_IND_LDPC_S               24
#define HTT_FW_OFFLOAD_IND_BEAMFORMED_M         0x02000000
#define HTT_FW_OFFLOAD_IND_BEAMFORMED_S         25

/* DWORD three*/
#define HTT_FW_OFFLOAD_IND_FRAMECTRL_M          0x0000ffff
#define HTT_FW_OFFLOAD_IND_FRAMECTRL_S          0
#define HTT_FW_OFFLOAD_IND_SEQNO_M              0xffff0000
#define HTT_FW_OFFLOAD_IND_SEQNO_S              16

 /* DWORD four */
#define HTT_FW_OFFLOAD_IND_TID_NUM_M            0x0000001f
#define HTT_FW_OFFLOAD_IND_TID_NUM_S            0
#define HTT_FW_OFFLOAD_IND_VDEV_ID_M            0x00001fe0
#define HTT_FW_OFFLOAD_IND_VDEV_ID_S            5

/* DWORD five */
#define HTT_FW_OFFLOAD_IND_STATUS_M             0x00000007
#define HTT_FW_OFFLOAD_IND_STATUS_S             0
#define HTT_FW_OFFLOAD_IND_FORMAT_M             0x00000008
#define HTT_FW_OFFLOAD_IND_FORMAT_S             3
#define HTT_FW_OFFLOAD_IND_TX_MPDU_BYTES_M      0x000ffff0
#define HTT_FW_OFFLOAD_IND_TX_MPDU_BYTES_S      4
#define HTT_FW_OFFLOAD_IND_TX_RETRY_CNT_M       0x03f00000
#define HTT_FW_OFFLOAD_IND_TX_RETRY_CNT_S       20

#define HTT_FW_OFFLOAD_IND_PHY_TIMESTAMP_L32_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_PHY_TIMESTAMP_L32, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_PHY_TIMESTAMP_L32_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_PHY_TIMESTAMP_L32_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_PHY_TIMESTAMP_L32_M) >> HTT_FW_OFFLOAD_IND_PHY_TIMESTAMP_L32_S)

#define HTT_FW_OFFLOAD_IND_PREAMBLE_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_PREAMBLE, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_PREAMBLE_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_PREAMBLE_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_PREAMBLE_M) >> HTT_FW_OFFLOAD_IND_PREAMBLE_S)

#define HTT_FW_OFFLOAD_IND_MCS_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_MCS, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_MCS_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_MCS_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_MCS_M) >> HTT_FW_OFFLOAD_IND_MCS_S)

#define HTT_FW_OFFLOAD_IND_RATE_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_RATE, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_RATE_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_RATE_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_RATE_M) >> HTT_FW_OFFLOAD_IND_RATE_S)

#define HTT_FW_OFFLOAD_IND_RSSI_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_RSSI, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_RSSI_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_RSSI_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_RSSI_M) >> HTT_FW_OFFLOAD_IND_RSSI_S)


#define HTT_FW_OFFLOAD_IND_NSS_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_NSS, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_NSS_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_NSS_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_NSS_M) >> HTT_FW_OFFLOAD_IND_NSS_S)

#define HTT_FW_OFFLOAD_IND_BW_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_BW, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_BW_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_BW_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_BW_M) >> HTT_FW_OFFLOAD_IND_BW_S)


#define HTT_FW_OFFLOAD_IND_STBC_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_STBC, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_STBC_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_STBC_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_STBC_M) >> HTT_FW_OFFLOAD_IND_STBC_S)


#define HTT_FW_OFFLOAD_IND_SGI_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_SGI, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_SGI_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_SGI_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_SGI_M) >> HTT_FW_OFFLOAD_IND_SGI_S)

#define HTT_FW_OFFLOAD_IND_LDPC_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_LDPC, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_LDPC_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_LDPC_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_LDPC_M) >> HTT_FW_OFFLOAD_IND_LDPC_S)

#define HTT_FW_OFFLOAD_IND_BEAMFORMED_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_BEAMFORMED, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_BEAMFORMED_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_BEAMFORMED_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_BEAMFORMED_M) >> HTT_FW_OFFLOAD_IND_BEAMFORMED_S)

#define HTT_FW_OFFLOAD_IND_FRAMECTRL_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_FRAMECTRL, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_FRAMECTRL_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_FRAMECTRL_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_FRAMECTRL_M) >> HTT_FW_OFFLOAD_IND_FRAMECTRL_S)


#define HTT_FW_OFFLOAD_IND_SEQNO_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_SEQNO, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_SEQNO_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_SEQNO_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_SEQNO_M) >> HTT_FW_OFFLOAD_IND_SEQNO_S)

#define HTT_FW_OFFLOAD_IND_TID_NUM_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_TID_NUM, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_TID_NUM_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_TID_NUM_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_TID_NUM_M) >> HTT_FW_OFFLOAD_IND_TID_NUM_S)

#define HTT_FW_OFFLOAD_IND_VDEV_ID_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_VDEV_ID, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_VDEV_ID_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_VDEV_ID_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_VDEV_ID_M) >> HTT_FW_OFFLOAD_IND_VDEV_ID_S)

#define HTT_FW_OFFLOAD_IND_STATUS_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_STATUS, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_STATUS_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_STATUS_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_STATUS_M) >> HTT_FW_OFFLOAD_IND_STATUS_M)


#define HTT_FW_OFFLOAD_IND_FORMAT_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_FORMAT, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_FORMAT_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_FORMAT_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_FORMAT_M) >> HTT_FW_OFFLOAD_IND_FORMAT_S)


#define HTT_FW_OFFLOAD_IND_TX_MPDU_BYTES_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_TX_MPDU_BYTES, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_TX_MPDU_BYTES_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_TX_MPDU_BYTES_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_TX_MPDU_BYTES_M) >> HTT_FW_OFFLOAD_IND_TX_MPDU_BYTES_S)

#define HTT_FW_OFFLOAD_IND_TX_RETRY_CNT_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_OFFLOAD_IND_TX_RETRY_CNT, value); \
        (word) |= (value)  << HTT_FW_OFFLOAD_IND_TX_RETRY_CNT_S; \
    } while (0)
#define HTT_FW_OFFLOAD_IND_TX_RETRY_CNT_GET(word) \
    (((word) & HTT_FW_OFFLOAD_IND_TX_RETRY_CNT_M) >> HTT_FW_OFFLOAD_IND_TX_RETRY_CNT_S)


/*
 * @brief target -> host rx reorder flush message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_FLUSH
 *
 * @details
 * The following field definitions describe the format of the rx flush
 * message sent from the target to the host.
 * The message consists of a 4-octet header, followed by one or more
 * 4-octet payload information elements.
 *
 *     |31           24|23                            8|7            0|
 *     |--------------------------------------------------------------|
 *     |       TID     |          peer ID              |   msg type   |
 *     |--------------------------------------------------------------|
 *     |  seq num end  | seq num start |  MPDU status  |   reserved   |
 *     |--------------------------------------------------------------|
 * First DWORD:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx flush message
 *     Value: 0x2 (HTT_T2H_MSG_TYPE_RX_FLUSH)
 *   - PEER_ID
 *     Bits 23:8 (only bits 18:8 actually used)
 *     Purpose: identify which peer's rx data is being flushed
 *     Value: (rx) peer ID
 *   - TID
 *     Bits 31:24 (only bits 27:24 actually used)
 *     Purpose: Specifies which traffic identifier's rx data is being flushed
 *     Value: traffic identifier
 * Second DWORD:
 *   - MPDU_STATUS
 *     Bits 15:8
 *     Purpose:
 *         Indicate whether the flushed MPDUs should be discarded or processed.
 *     Value:
 *         0x1:   send the MPDUs from the rx reorder buffer to subsequent
 *                stages of rx processing
 *         other: discard the MPDUs
 *         It is anticipated that flush messages will always have
 *         MPDU status == 1, but the status flag is included for
 *         flexibility.
 *   - SEQ_NUM_START
 *     Bits 23:16
 *     Purpose:
 *         Indicate the start of a series of consecutive MPDUs being flushed.
 *         Not all MPDUs within this range are necessarily valid - the host
 *         must check each sequence number within this range to see if the
 *         corresponding MPDU is actually present.
 *     Value:
 *         The sequence number for the first MPDU in the sequence.
 *         This sequence number is the 6 LSBs of the 802.11 sequence number.
 *   - SEQ_NUM_END
 *     Bits 30:24
 *     Purpose:
 *         Indicate the end of a series of consecutive MPDUs being flushed.
 *     Value:
 *         The sequence number one larger than the sequence number of the
 *         last MPDU being flushed.
 *         This sequence number is the 6 LSBs of the 802.11 sequence number.
 *         The range of MPDUs from [SEQ_NUM_START,SEQ_NUM_END-1] inclusive
 *         are to be released for further rx processing.
 *         Not all MPDUs within this range are necessarily valid - the host
 *         must check each sequence number within this range to see if the
 *         corresponding MPDU is actually present.
 */
/* first DWORD */
#define HTT_RX_FLUSH_PEER_ID_M  0xffff00
#define HTT_RX_FLUSH_PEER_ID_S  8
#define HTT_RX_FLUSH_TID_M      0xff000000
#define HTT_RX_FLUSH_TID_S      24
/* second DWORD */
#define HTT_RX_FLUSH_MPDU_STATUS_M   0x0000ff00
#define HTT_RX_FLUSH_MPDU_STATUS_S   8
#define HTT_RX_FLUSH_SEQ_NUM_START_M 0x00ff0000
#define HTT_RX_FLUSH_SEQ_NUM_START_S 16
#define HTT_RX_FLUSH_SEQ_NUM_END_M   0xff000000
#define HTT_RX_FLUSH_SEQ_NUM_END_S   24

#define HTT_RX_FLUSH_BYTES 8

#define HTT_RX_FLUSH_PEER_ID_SET(word, value)                           \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_FLUSH_PEER_ID, value);                 \
        (word) |= (value)  << HTT_RX_FLUSH_PEER_ID_S;                   \
    } while (0)
#define HTT_RX_FLUSH_PEER_ID_GET(word) \
    (((word) & HTT_RX_FLUSH_PEER_ID_M) >> HTT_RX_FLUSH_PEER_ID_S)

#define HTT_RX_FLUSH_TID_SET(word, value)                               \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_FLUSH_TID, value);                     \
        (word) |= (value)  << HTT_RX_FLUSH_TID_S;                       \
    } while (0)
#define HTT_RX_FLUSH_TID_GET(word) \
    (((word) & HTT_RX_FLUSH_TID_M) >> HTT_RX_FLUSH_TID_S)

#define HTT_RX_FLUSH_MPDU_STATUS_SET(word, value)                       \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_FLUSH_MPDU_STATUS, value);             \
        (word) |= (value)  << HTT_RX_FLUSH_MPDU_STATUS_S;               \
    } while (0)
#define HTT_RX_FLUSH_MPDU_STATUS_GET(word) \
    (((word) & HTT_RX_FLUSH_MPDU_STATUS_M) >> HTT_RX_FLUSH_MPDU_STATUS_S)

#define HTT_RX_FLUSH_SEQ_NUM_START_SET(word, value)                     \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_FLUSH_SEQ_NUM_START, value);           \
        (word) |= (value)  << HTT_RX_FLUSH_SEQ_NUM_START_S;             \
    } while (0)
#define HTT_RX_FLUSH_SEQ_NUM_START_GET(word) \
    (((word) & HTT_RX_FLUSH_SEQ_NUM_START_M) >> HTT_RX_FLUSH_SEQ_NUM_START_S)

#define HTT_RX_FLUSH_SEQ_NUM_END_SET(word, value)                       \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_FLUSH_SEQ_NUM_END, value);             \
        (word) |= (value)  << HTT_RX_FLUSH_SEQ_NUM_END_S;               \
    } while (0)
#define HTT_RX_FLUSH_SEQ_NUM_END_GET(word) \
    (((word) & HTT_RX_FLUSH_SEQ_NUM_END_M) >> HTT_RX_FLUSH_SEQ_NUM_END_S)

/*
 * @brief target -> host rx pn check indication message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_PN_IND
 *
 * @details
 * The following field definitions describe the format of the Rx PN check
 * indication message sent from the target to the host.
 * The message consists of a 4-octet header, followed by the start and
 * end sequence numbers to be released, followed by the PN IEs. Each PN
 * IE is one octet containing the sequence number that failed the PN
 * check.
 *
 *     |31           24|23                            8|7            0|
 *     |--------------------------------------------------------------|
 *     |       TID     |          peer ID              |   msg type   |
 *     |--------------------------------------------------------------|
 *     |  Reserved     | PN IE count   | seq num end   | seq num start|
 *     |--------------------------------------------------------------|
 *     l               :    PN IE 2    |    PN IE 1    |   PN IE 0    |
 *     |--------------------------------------------------------------|

 * First DWORD:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: Identifies this as an rx pn check indication message
 *     Value: 0x10 (HTT_T2H_MSG_TYPE_RX_PN_IND)
 *   - PEER_ID
 *     Bits 23:8 (only bits 18:8 actually used)
 *     Purpose: identify which peer
 *     Value: (rx) peer ID
 *   - TID
 *     Bits 31:24 (only bits 27:24 actually used)
 *     Purpose: identify traffic identifier
 *     Value: traffic identifier
 * Second DWORD:
 *   - SEQ_NUM_START
 *     Bits 7:0
 *     Purpose:
 *        Indicates the starting sequence number of the MPDU in this
 *        series of MPDUs that went though PN check.
 *     Value:
 *        The sequence number for the first MPDU in the sequence.
 *        This sequence number is the 6 LSBs of the 802.11 sequence number.
 *   - SEQ_NUM_END
 *     Bits 15:8
 *     Purpose:
 *        Indicates the ending sequence number of the MPDU in this
 *        series of MPDUs that went though PN check.
 *     Value:
 *        The sequence number one larger then the sequence number of the last
 *        MPDU being flushed.
 *        This sequence number is the 6 LSBs of the 802.11 sequence number.
 *        The range of MPDUs from [SEQ_NUM_START,SEQ_NUM_END-1] have been checked
 *        for invalid PN numbers and are ready to be released for further processing.
 *        Not all MPDUs within this range are necessarily valid - the host
 *        must check each sequence number within this range to see if the
 *        corresponding MPDU is actually present.
 *   - PN_IE_COUNT
 *     Bits 23:16
 *     Purpose:
 *        Used to determine the variable number of PN information elements in this
 *        message
 *
 * PN information elements:
 *  - PN_IE_x-
 *      Purpose:
 *          Each PN information element contains the sequence number of the MPDU that
 *          has failed the target PN check.
 *      Value:
 *          Contains the 6 LSBs of the 802.11 sequence number corresponding to the MPDU
 *          that failed the PN check.
 */
/* first DWORD */
#define HTT_RX_PN_IND_PEER_ID_M  0xffff00
#define HTT_RX_PN_IND_PEER_ID_S  8
#define HTT_RX_PN_IND_TID_M      0xff000000
#define HTT_RX_PN_IND_TID_S      24
/* second DWORD */
#define HTT_RX_PN_IND_SEQ_NUM_START_M 0x000000ff
#define HTT_RX_PN_IND_SEQ_NUM_START_S 0
#define HTT_RX_PN_IND_SEQ_NUM_END_M   0x0000ff00
#define HTT_RX_PN_IND_SEQ_NUM_END_S   8
#define HTT_RX_PN_IND_PN_IE_CNT_M     0x00ff0000
#define HTT_RX_PN_IND_PN_IE_CNT_S     16

#define HTT_RX_PN_IND_BYTES 8

#define HTT_RX_PN_IND_PEER_ID_SET(word, value)                           \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_PN_IND_PEER_ID, value);                 \
        (word) |= (value)  << HTT_RX_PN_IND_PEER_ID_S;                   \
    } while (0)
#define HTT_RX_PN_IND_PEER_ID_GET(word) \
    (((word) & HTT_RX_PN_IND_PEER_ID_M) >> HTT_RX_PN_IND_PEER_ID_S)

#define HTT_RX_PN_IND_EXT_TID_SET(word, value)                               \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_PN_IND_TID, value);                     \
        (word) |= (value)  << HTT_RX_PN_IND_TID_S;                       \
    } while (0)
#define HTT_RX_PN_IND_EXT_TID_GET(word) \
    (((word) & HTT_RX_PN_IND_TID_M) >> HTT_RX_PN_IND_TID_S)

#define HTT_RX_PN_IND_SEQ_NUM_START_SET(word, value)                     \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_PN_IND_SEQ_NUM_START, value);           \
        (word) |= (value)  << HTT_RX_PN_IND_SEQ_NUM_START_S;             \
    } while (0)
#define HTT_RX_PN_IND_SEQ_NUM_START_GET(word) \
    (((word) & HTT_RX_PN_IND_SEQ_NUM_START_M) >> HTT_RX_PN_IND_SEQ_NUM_START_S)

#define HTT_RX_PN_IND_SEQ_NUM_END_SET(word, value)                       \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_PN_IND_SEQ_NUM_END, value);             \
        (word) |= (value)  << HTT_RX_PN_IND_SEQ_NUM_END_S;               \
    } while (0)
#define HTT_RX_PN_IND_SEQ_NUM_END_GET(word) \
    (((word) & HTT_RX_PN_IND_SEQ_NUM_END_M) >> HTT_RX_PN_IND_SEQ_NUM_END_S)

#define HTT_RX_PN_IND_PN_IE_CNT_SET(word, value)                         \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_PN_IND_PN_IE_CNT, value);               \
        (word) |= (value) << HTT_RX_PN_IND_PN_IE_CNT_S;                  \
    } while (0)
#define HTT_RX_PN_IND_PN_IE_CNT_GET(word)   \
    (((word) & HTT_RX_PN_IND_PN_IE_CNT_M) >> HTT_RX_PN_IND_PN_IE_CNT_S)

/*
 * @brief target -> host rx offload deliver message for LL system
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_OFFLOAD_DELIVER_IND
 *
 * @details
 * In a low latency system this message is sent whenever the offload
 * manager flushes out the packets it has coalesced in its coalescing buffer.
 * The DMA of the actual packets into host memory is done before sending out
 * this message. This message indicates only how many MSDUs to reap. The
 * peer ID, vdev ID, tid and MSDU length are copied inline into the header
 * portion of the MSDU while DMA'ing into the host memory. Unlike the packets
 * DMA'd by the MAC directly into host memory these packets do not contain
 * the MAC descriptors in the header portion of the packet. Instead they contain
 * the peer ID, vdev ID, tid and MSDU length. Also when the host receives this
 * message, the packets are delivered directly to the NW stack without going
 * through the regular reorder buffering and PN checking path since it has
 * already been done in target.
 *
 * |31             24|23             16|15              8|7               0|
 * |-----------------------------------------------------------------------|
 * |         Total MSDU count          |     reserved    |     msg type    |
 * |-----------------------------------------------------------------------|
 *
 * @brief target -> host rx offload deliver message for HL system
 *
 * @details
 * In a high latency system this message is sent whenever the offload manager
 * flushes out the packets it has coalesced in its coalescing buffer. The
 * actual packets are also carried along with this message. When the host
 * receives this message, it is expected to deliver these packets to the NW
 * stack directly instead of routing them through the reorder buffering and
 * PN checking path since it has already been done in target.
 *
 * |31             24|23             16|15              8|7               0|
 * |-----------------------------------------------------------------------|
 * |         Total MSDU count          |    reserved     |     msg type    |
 * |-----------------------------------------------------------------------|
 * |            peer ID                |              MSDU length          |
 * |-----------------------------------------------------------------------|
 * |  MSDU payload   |     FW Desc     |       tid       |   vdev ID       |
 * |-----------------------------------------------------------------------|
 * |                           MSDU payload contd.                         |
 * |-----------------------------------------------------------------------|
 * |            peer ID                |              MSDU length          |
 * |-----------------------------------------------------------------------|
 * |  MSDU payload   |    FW Desc      |       tid       |   vdev ID       |
 * |-----------------------------------------------------------------------|
 * |                           MSDU payload contd.                         |
 * |-----------------------------------------------------------------------|
 *
 */
/* first DWORD */
#define HTT_RX_OFFLOAD_DELIVER_IND_HDR_BYTES          4
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_HDR_BYTES     7

#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_CNT_M         0xffff0000
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_CNT_S         16
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_LEN_M         0x0000ffff
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_LEN_S         0
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_PEER_ID_M     0xffff0000
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_PEER_ID_S     16
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_VDEV_ID_M     0x000000ff
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_VDEV_ID_S     0
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_TID_M         0x0000ff00
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_TID_S         8
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_DESC_M        0x00ff0000
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_DESC_S        16

#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_CNT_GET(word) \
    (((word) & HTT_RX_OFFLOAD_DELIVER_IND_MSDU_CNT_M) >> HTT_RX_OFFLOAD_DELIVER_IND_MSDU_CNT_S)
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_CNT_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_OFFLOAD_DELIVER_IND_MSDU_CNT, value); \
        (word) |= (value) << HTT_RX_OFFLOAD_DELIVER_IND_MSDU_CNT_S; \
    } while (0)

#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_LEN_GET(word) \
    (((word) & HTT_RX_OFFLOAD_DELIVER_IND_MSDU_LEN_M) >> HTT_RX_OFFLOAD_DELIVER_IND_MSDU_LEN_S)
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_LEN_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_OFFLOAD_DELIVER_IND_MSDU_LEN, value); \
        (word) |= (value) << HTT_RX_OFFLOAD_DELIVER_IND_MSDU_LEN_S; \
    } while (0)

#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_PEER_ID_GET(word) \
    (((word) & HTT_RX_OFFLOAD_DELIVER_IND_MSDU_PEER_ID_M) >> HTT_RX_OFFLOAD_DELIVER_IND_MSDU_PEER_ID_S)
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_PEER_ID_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_OFFLOAD_DELIVER_IND_MSDU_PEER_ID, value); \
        (word) |= (value) << HTT_RX_OFFLOAD_DELIVER_IND_MSDU_PEER_ID_S; \
    } while (0)

#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_VDEV_ID_GET(word) \
    (((word) & HTT_RX_OFFLOAD_DELIVER_IND_MSDU_VDEV_ID_M) >> HTT_RX_OFFLOAD_DELIVER_IND_MSDU_VDEV_ID_S)
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_VDEV_ID_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_OFFLOAD_DELIVER_IND_MSDU_VDEV_ID, value); \
        (word) |= (value) << HTT_RX_OFFLOAD_DELIVER_IND_MSDU_VDEV_ID_S; \
    } while (0)

#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_TID_GET(word) \
    (((word) & HTT_RX_OFFLOAD_DELIVER_IND_MSDU_TID_M) >> HTT_RX_OFFLOAD_DELIVER_IND_MSDU_TID_S)
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_TID_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_OFFLOAD_DELIVER_IND_MSDU_TID, value); \
        (word) |= (value) << HTT_RX_OFFLOAD_DELIVER_IND_MSDU_TID_S; \
    } while (0)

#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_DESC_GET(word) \
    (((word) & HTT_RX_OFFLOAD_DELIVER_IND_MSDU_DESC_M) >> HTT_RX_OFFLOAD_DELIVER_IND_MSDU_DESC_S)
#define HTT_RX_OFFLOAD_DELIVER_IND_MSDU_DESC_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_OFFLOAD_DELIVER_IND_MSDU_DESC, value); \
        (word) |= (value) << HTT_RX_OFFLOAD_DELIVER_IND_MSDU_DESC_S; \
    } while (0)

/**
 * @brief target -> host rx peer map/unmap message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_PEER_MAP
 *
 * @details
 * The following diagram shows the format of the rx peer map message sent
 * from the target to the host.  This layout assumes the target operates
 * as little-endian.
 *
 * This message always contains a SW peer ID.  The main purpose of the
 * SW peer ID is to tell the host what peer ID rx packets will be tagged
 * with, so that the host can use that peer ID to determine which peer
 * transmitted the rx frame.  This SW peer ID is sometimes also used for
 * other purposes, such as identifying during tx completions which peer
 * the tx frames in question were transmitted to.
 *
 * In certain generations of chips, the peer map message also contains
 * a HW peer ID.  This HW peer ID is used during rx --> tx frame forwarding
 * to identify which peer the frame needs to be forwarded to (i.e. the
 * peer assocated with the Destination MAC Address within the packet),
 * and particularly which vdev needs to transmit the frame (for cases
 * of inter-vdev rx --> tx forwarding). The HW peer id here is the same
 * meaning as AST_INDEX_0.
 * This DA-based peer ID that is provided for certain rx frames
 * (the rx frames that need to be re-transmitted as tx frames)
 * is the ID that the HW uses for referring to the peer in question,
 * rather than the peer ID that the SW+FW use to refer to the peer.
 *
 *
 * |31             24|23             16|15              8|7               0|
 * |-----------------------------------------------------------------------|
 * |            SW peer ID             |     VDEV ID     |     msg type    |
 * |-----------------------------------------------------------------------|
 * |    MAC addr 3   |    MAC addr 2   |    MAC addr 1   |    MAC addr 0   |
 * |-----------------------------------------------------------------------|
 * |      HW peer ID / AST index 0     |    MAC addr 5   |    MAC addr 4   |
 * |-----------------------------------------------------------------------|
 *
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_PEER_UNMAP
 *
 * The following diagram shows the format of the rx peer unmap message sent
 * from the target to the host.
 *
 * |31             24|23             16|15              8|7               0|
 * |-----------------------------------------------------------------------|
 * |            SW peer ID             |     VDEV ID     |     msg type    |
 * |-----------------------------------------------------------------------|
 *
 * The following field definitions describe the format of the rx peer map
 * and peer unmap messages sent from the target to the host.
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx peer map or peer unmap message
 *     Value: peer map   -> 0x3 (HTT_T2H_MSG_TYPE_PEER_MAP),
 *            peer unmap -> 0x4 (HTT_T2H_MSG_TYPE_PEER_UNMAP)
 *   - VDEV_ID
 *     Bits 15:8
 *     Purpose: Indicates which virtual device the peer is associated
 *         with.
 *     Value: vdev ID (used in the host to look up the vdev object)
 *   - PEER_ID (a.k.a. SW_PEER_ID)
 *     Bits 31:16
 *     Purpose: The peer ID (index) that WAL is allocating (map) or
 *         freeing (unmap)
 *     Value: (rx) peer ID
 *   - MAC_ADDR_L32 (peer map only)
 *     Bits 31:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: lower 4 bytes of peer node's MAC address
 *   - MAC_ADDR_U16 (peer map only)
 *     Bits 15:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: upper 2 bytes of peer node's MAC address
 *   - HW_PEER_ID
 *     Bits 31:16
 *     Purpose: Identifies the HW peer ID corresponding to the peer MAC
 *         address, so for rx frames marked for rx --> tx forwarding, the
 *         host can determine from the HW peer ID provided as meta-data with
 *         the rx frame which peer the frame is supposed to be forwarded to.
 *     Value: ID used by the MAC HW to identify the peer
 */
#define HTT_RX_PEER_MAP_VDEV_ID_M       0xff00
#define HTT_RX_PEER_MAP_VDEV_ID_S       8
#define HTT_RX_PEER_MAP_PEER_ID_M      0xffff0000
#define HTT_RX_PEER_MAP_PEER_ID_S      16
#define HTT_RX_PEER_MAP_SW_PEER_ID_M HTT_RX_PEER_MAP_PEER_ID_M /* alias */
#define HTT_RX_PEER_MAP_SW_PEER_ID_S HTT_RX_PEER_MAP_PEER_ID_S /* alias */
#define HTT_RX_PEER_MAP_MAC_ADDR_L32_M 0xffffffff
#define HTT_RX_PEER_MAP_MAC_ADDR_L32_S 0
#define HTT_RX_PEER_MAP_MAC_ADDR_U16_M 0xffff
#define HTT_RX_PEER_MAP_MAC_ADDR_U16_S 0
#define HTT_RX_PEER_MAP_HW_PEER_ID_M   0xffff0000
#define HTT_RX_PEER_MAP_HW_PEER_ID_S   16

#define HTT_RX_PEER_MAP_VAP_ID_SET HTT_RX_PEER_MAP_VDEV_ID_SET /* deprecated */
#define HTT_RX_PEER_MAP_VDEV_ID_SET(word, value)                         \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_VDEV_ID, value);               \
        (word) |= (value)  << HTT_RX_PEER_MAP_VDEV_ID_S;                 \
    } while (0)
#define HTT_RX_PEER_MAP_VAP_ID_GET HTT_RX_PEER_MAP_VDEV_ID_GET /* deprecated */
#define HTT_RX_PEER_MAP_VDEV_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_VDEV_ID_M) >> HTT_RX_PEER_MAP_VDEV_ID_S)

#define HTT_RX_PEER_MAP_PEER_ID_SET(word, value)                        \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_PEER_ID, value);              \
        (word) |= (value)  << HTT_RX_PEER_MAP_PEER_ID_S;                \
    } while (0)
#define HTT_RX_PEER_MAP_PEER_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_PEER_ID_M) >> HTT_RX_PEER_MAP_PEER_ID_S)
#define HTT_RX_PEER_MAP_SW_PEER_ID_SET HTT_RX_PEER_MAP_PEER_ID_SET /* alias */
#define HTT_RX_PEER_MAP_SW_PEER_ID_GET HTT_RX_PEER_MAP_PEER_ID_GET /* alias */

#define HTT_RX_PEER_MAP_HW_PEER_ID_SET(word, value)            \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_HW_PEER_ID, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_HW_PEER_ID_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_HW_PEER_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_HW_PEER_ID_M) >> HTT_RX_PEER_MAP_HW_PEER_ID_S)

#define HTT_RX_PEER_MAP_MAC_ADDR_OFFSET 4 /* bytes */
#define HTT_RX_PEER_MAP_HW_PEER_ID_OFFSET 8 /* bytes */

#define HTT_RX_PEER_MAP_BYTES 12


#define HTT_RX_PEER_UNMAP_PEER_ID_M      HTT_RX_PEER_MAP_PEER_ID_M
#define HTT_RX_PEER_UNMAP_PEER_ID_S      HTT_RX_PEER_MAP_PEER_ID_S
#define HTT_RX_PEER_UNMAP_SW_PEER_ID_M   HTT_RX_PEER_MAP_SW_PEER_ID_M
#define HTT_RX_PEER_UNMAP_SW_PEER_ID_S   HTT_RX_PEER_MAP_SW_PEER_ID_S

#define HTT_RX_PEER_UNMAP_PEER_ID_SET    HTT_RX_PEER_MAP_PEER_ID_SET
#define HTT_RX_PEER_UNMAP_PEER_ID_GET    HTT_RX_PEER_MAP_PEER_ID_GET

#define HTT_RX_PEER_UNMAP_VDEV_ID_SET    HTT_RX_PEER_MAP_VDEV_ID_SET
#define HTT_RX_PEER_UNMAP_VDEV_ID_GET    HTT_RX_PEER_MAP_VDEV_ID_GET

#define HTT_RX_PEER_UNMAP_BYTES 4


/**
 * @brief target -> host rx peer map V2 message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_PEER_MAP_V2
 *
 * @details
 * The following diagram shows the format of the rx peer map v2 message sent
 * from the target to the host.  This layout assumes the target operates
 * as little-endian.
 *
 * This message always contains a SW peer ID.  The main purpose of the
 * SW peer ID is to tell the host what peer ID rx packets will be tagged
 * with, so that the host can use that peer ID to determine which peer
 * transmitted the rx frame.  This SW peer ID is sometimes also used for
 * other purposes, such as identifying during tx completions which peer
 * the tx frames in question were transmitted to.
 *
 * The peer map v2 message also contains a HW peer ID.  This HW peer ID
 * is used during rx --> tx frame forwarding to identify which peer the
 * frame needs to be forwarded to (i.e. the peer assocated with the
 * Destination MAC Address within the packet), and particularly which vdev
 * needs to transmit the frame (for cases of inter-vdev rx --> tx forwarding).
 * This DA-based peer ID that is provided for certain rx frames
 * (the rx frames that need to be re-transmitted as tx frames)
 * is the ID that the HW uses for referring to the peer in question,
 * rather than the peer ID that the SW+FW use to refer to the peer.
 *
 * The HW peer id here is the same meaning as AST_INDEX_0.
 * Some chips support up to 4 AST indices per peer: AST_INDEX_0, AST_INDEX_1,
 * AST_INDEX_2, and AST_INDEX_3.  AST 0 is always valid; for AST 1 through
 * AST 3, check the AST_VALID_MASK(3) to see if the corresponding extension
 * AST is valid.
 *
 * |31    28|27    24|23   21|20|19 17|16|15              8|7               0|
 * |-------------------------------------------------------------------------|
 * |              SW peer ID             |     VDEV ID     |     msg type    |
 * |-------------------------------------------------------------------------|
 * |    MAC addr 3   |    MAC addr 2     |    MAC addr 1   |    MAC addr 0   |
 * |-------------------------------------------------------------------------|
 * |       HW peer ID / AST index 0      |    MAC addr 5   |    MAC addr 4   |
 * |-------------------------------------------------------------------------|
 * |     Reserved_21_31      |OA|ASTVM|NH|          AST Hash Value           |
 * |-------------------------------------------------------------------------|
 * | ASTFM3 | ASTFM2 |  ASTFM1  | ASTFM0 |           AST index 1             |
 * |-------------------------------------------------------------------------|
 * |TID valid low pri|  TID valid hi pri |           AST index 2             |
 * |-------------------------------------------------------------------------|
 * |      LMAC/PMAC_RXPCU AST index      |           AST index 3             |
 * |-------------------------------------------------------------------------|
 * |                                 Reserved_2                              |
 * |-------------------------------------------------------------------------|
 * Where:
 *    NH = Next Hop
 *    ASTVM = AST valid mask
 *    OA = on-chip AST valid bit
 *    ASTFM = AST flow mask
 *
 * The following field definitions describe the format of the rx peer map v2
 * messages sent from the target to the host.
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx peer map v2 message
 *     Value: peer map v2 -> 0x1e (HTT_T2H_MSG_TYPE_PEER_MAP_V2)
 *   - VDEV_ID
 *     Bits 15:8
 *     Purpose: Indicates which virtual device the peer is associated with.
 *     Value: vdev ID (used in the host to look up the vdev object)
 *   - SW_PEER_ID
 *     Bits 31:16
 *     Purpose: The peer ID (index) that WAL is allocating
 *     Value: (rx) peer ID
 *   - MAC_ADDR_L32
 *     Bits 31:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: lower 4 bytes of peer node's MAC address
 *   - MAC_ADDR_U16
 *     Bits 15:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: upper 2 bytes of peer node's MAC address
 *   - HW_PEER_ID / AST_INDEX_0
 *     Bits 31:16
 *     Purpose: Identifies the HW peer ID corresponding to the peer MAC
 *         address, so for rx frames marked for rx --> tx forwarding, the
 *         host can determine from the HW peer ID provided as meta-data with
 *         the rx frame which peer the frame is supposed to be forwarded to.
 *     Value: ID used by the MAC HW to identify the peer
 *   - AST_HASH_VALUE
 *     Bits 15:0
 *     Purpose: Indicates AST Hash value is required for the TCL AST index
 *         override feature.
 *   - NEXT_HOP
 *     Bit 16
 *     Purpose: Bit indicates that a next_hop AST entry is used for WDS
 *         (Wireless Distribution System).
 *   - AST_VALID_MASK
 *     Bits  19:17
 *     Purpose: Indicate if the AST 1 through AST 3 are valid
 *   - ONCHIP_AST_VALID_FLAG
 *     Bit 20
 *     Purpose: Indicate if the on-chip AST index field (ONCHIP_AST_IDX)
 *         is valid.
 *   - AST_INDEX_1
 *     Bits 15:0
 *     Purpose: indicate the second AST index for this peer
 *   - AST_0_FLOW_MASK
 *     Bits 19:16
 *     Purpose: identify the which flow the AST 0 entry corresponds to.
 *   - AST_1_FLOW_MASK
 *     Bits 23:20
 *     Purpose: identify the which flow the AST 1 entry corresponds to.
 *   - AST_2_FLOW_MASK
 *     Bits 27:24
 *     Purpose: identify the which flow the AST 2 entry corresponds to.
 *   - AST_3_FLOW_MASK
 *     Bits 31:28
 *     Purpose: identify the which flow the AST 3 entry corresponds to.
 *   - AST_INDEX_2
 *     Bits 15:0
 *     Purpose: indicate the third AST index for this peer
 *   - TID_VALID_HI_PRI
 *     Bits 23:16
 *     Purpose: identify if this peer's TIDs 0-7 support HI priority flow
 *   - TID_VALID_LOW_PRI
 *     Bits 31:24
 *     Purpose: identify if this peer's TIDs 0-7 support Low priority flow
 *   - AST_INDEX_3
 *     Bits 15:0
 *     Purpose: indicate the fourth AST index for this peer
 *   - ONCHIP_AST_IDX / RESERVED
 *     Bits 31:16
 *     Purpose: This field is valid only when split AST feature is enabled.
 *         The ONCHIP_AST_VALID_FLAG identifies whether this field is valid.
 *         If valid, identifies the HW peer ID corresponding to the peer MAC
 *         address, this ast_idx is used for LMAC modules for RXPCU.
 *     Value: ID used by the LMAC HW to identify the peer
 */
#define HTT_RX_PEER_MAP_V2_VDEV_ID_M        0xff00
#define HTT_RX_PEER_MAP_V2_VDEV_ID_S        8
#define HTT_RX_PEER_MAP_V2_SW_PEER_ID_M     0xffff0000
#define HTT_RX_PEER_MAP_V2_SW_PEER_ID_S     16
#define HTT_RX_PEER_MAP_V2_MAC_ADDR_L32_M   0xffffffff
#define HTT_RX_PEER_MAP_V2_MAC_ADDR_L32_S   0
#define HTT_RX_PEER_MAP_V2_MAC_ADDR_U16_M   0xffff
#define HTT_RX_PEER_MAP_V2_MAC_ADDR_U16_S   0
#define HTT_RX_PEER_MAP_V2_HW_PEER_ID_M     0xffff0000
#define HTT_RX_PEER_MAP_V2_HW_PEER_ID_S     16
#define HTT_RX_PEER_MAP_V2_AST_HASH_VALUE_M 0x0000ffff
#define HTT_RX_PEER_MAP_V2_AST_HASH_VALUE_S 0
#define HTT_RX_PEER_MAP_V2_NEXT_HOP_M       0x00010000
#define HTT_RX_PEER_MAP_V2_NEXT_HOP_S       16
#define HTT_RX_PEER_MAP_V2_AST_VALID_MASK_M     0x000e0000
#define HTT_RX_PEER_MAP_V2_AST_VALID_MASK_S     17

#define HTT_RX_PEER_MAP_V2_ONCHIP_AST_VALID_FLAG_M 0x00100000
#define HTT_RX_PEER_MAP_V2_ONCHIP_AST_VALID_FLAG_S 20

#define HTT_RX_PEER_MAP_V2_AST_INDEX_1_M        0xffff
#define HTT_RX_PEER_MAP_V2_AST_INDEX_1_S        0
#define HTT_RX_PEER_MAP_V2_AST_0_FLOW_MASK_M    0x000f0000
#define HTT_RX_PEER_MAP_V2_AST_0_FLOW_MASK_S    16
#define HTT_RX_PEER_MAP_V2_AST_1_FLOW_MASK_M    0x00f00000
#define HTT_RX_PEER_MAP_V2_AST_1_FLOW_MASK_S    20
#define HTT_RX_PEER_MAP_V2_AST_2_FLOW_MASK_M    0x0f000000
#define HTT_RX_PEER_MAP_V2_AST_2_FLOW_MASK_S    24
#define HTT_RX_PEER_MAP_V2_AST_3_FLOW_MASK_M    0xf0000000
#define HTT_RX_PEER_MAP_V2_AST_3_FLOW_MASK_S    28

#define HTT_RX_PEER_MAP_V2_AST_INDEX_2_M        0xffff
#define HTT_RX_PEER_MAP_V2_AST_INDEX_2_S        0
#define HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI_M   0x00ff0000
#define HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI_S   16
#define HTT_RX_PEER_MAP_V2_TID_VALID_LOW_PRI_M  0xff000000
#define HTT_RX_PEER_MAP_V2_TID_VALID_LOW_PRI_S  24

#define HTT_RX_PEER_MAP_V2_AST_INDEX_3_M        0xffff
#define HTT_RX_PEER_MAP_V2_AST_INDEX_3_S        0

#define HTT_RX_PEER_MAP_V2_ONCHIP_AST_HASH_VALUE_M 0xffff0000
#define HTT_RX_PEER_MAP_V2_ONCHIP_AST_HASH_VALUE_S 16

#define HTT_RX_PEER_MAP_V2_VDEV_ID_SET(word, value)           \
    do {                                                      \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_VDEV_ID, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_VDEV_ID_S;   \
    } while (0)
#define HTT_RX_PEER_MAP_V2_VDEV_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_VDEV_ID_M) >> HTT_RX_PEER_MAP_V2_VDEV_ID_S)

#define HTT_RX_PEER_MAP_V2_SW_PEER_ID_SET(word, value)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_SW_PEER_ID, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_SW_PEER_ID_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V2_SW_PEER_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_SW_PEER_ID_M) >> HTT_RX_PEER_MAP_V2_SW_PEER_ID_S)

#define HTT_RX_PEER_MAP_V2_HW_PEER_ID_SET(word, value)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_HW_PEER_ID, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_HW_PEER_ID_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V2_HW_PEER_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_HW_PEER_ID_M) >> HTT_RX_PEER_MAP_V2_HW_PEER_ID_S)

#define HTT_RX_PEER_MAP_V2_AST_HASH_VALUE_SET(word, value)            \
    do {                                                              \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_HASH_VALUE, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_HASH_VALUE_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_HASH_VALUE_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_HASH_VALUE_M) >> HTT_RX_PEER_MAP_V2_AST_HASH_VALUE_S)

#define HTT_RX_PEER_MAP_V2_ONCHIP_AST_HASH_VALUE_SET(word, value)             \
    do {                                                                      \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_ONCHIP_AST_HASH_VALUE_M, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_ONCHIP_AST_HASH_VALUE_S;     \
    } while (0)
#define HTT_RX_PEER_MAP_V2_ONCHIP_AST_HASH_VALUE_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_ONCHIP_AST_HASH_VALUE_M) >> HTT_RX_PEER_MAP_V2_ONCHIP_AST_HASH_VALUE_S)

#define HTT_RX_PEER_MAP_V2_NEXT_HOP_SET(word, value)            \
    do {                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_NEXT_HOP, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_NEXT_HOP_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V2_NEXT_HOP_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_NEXT_HOP_M) >> HTT_RX_PEER_MAP_V2_NEXT_HOP_S)

#define HTT_RX_PEER_MAP_V2_AST_VALID_MASK_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_VALID_MASK, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_VALID_MASK_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_VALID_MASK_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_VALID_MASK_M) >> HTT_RX_PEER_MAP_V2_AST_VALID_MASK_S)

#define HTT_RX_PEER_MAP_V2_ONCHIP_AST_VALID_FLAG_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_ONCHIP_AST_VALID_FLAG_M, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_ONCHIP_AST_VALID_FLAG_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_ONCHIP_AST_VALID_MASK_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_ONCHIP_AST_VALID_FLAG_M) >> HTT_RX_PEER_MAP_V2_ONCHIP_AST_VALID_FLAG_S)

#define HTT_RX_PEER_MAP_V2_AST_INDEX_1_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_INDEX_1, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_INDEX_1_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_INDEX_1_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_INDEX_1_M) >> HTT_RX_PEER_MAP_V2_AST_INDEX_1_S)

#define HTT_RX_PEER_MAP_V2_AST_0_FLOW_MASK_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_0_FLOW_MASK, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_0_FLOW_MASK_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_0_FLOW_MASK_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_0_FLOW_MASK_M) >> HTT_RX_PEER_MAP_V2_AST_0_FLOW_MASK_S)

#define HTT_RX_PEER_MAP_V2_AST_1_FLOW_MASK_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_1_FLOW_MASK, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_1_FLOW_MASK_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_1_FLOW_MASK_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_1_FLOW_MASK_M) >> HTT_RX_PEER_MAP_V2_AST_1_FLOW_MASK_S)

#define HTT_RX_PEER_MAP_V2_AST_2_FLOW_MASK_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_2_FLOW_MASK, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_2_FLOW_MASK_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_2_FLOW_MASK_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_2_FLOW_MASK_M) >> HTT_RX_PEER_MAP_V2_AST_2_FLOW_MASK_S)

#define HTT_RX_PEER_MAP_V2_AST_3_FLOW_MASK_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_3_FLOW_MASK, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_3_FLOW_MASK_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_3_FLOW_MASK_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_3_FLOW_MASK_M) >> HTT_RX_PEER_MAP_V2_AST_3_FLOW_MASK_S)

#define HTT_RX_PEER_MAP_V2_AST_INDEX_2_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_INDEX_2, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_INDEX_2_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_INDEX_2_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_INDEX_2_M) >> HTT_RX_PEER_MAP_V2_AST_INDEX_2_S)
#define HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI_M) >> HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI_S)

#define HTT_RX_PEER_MAP_V2_TID_VALID_LOW_PRI_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_TID_VALID_LOW_PRI, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_TID_VALID_LOW_PRI_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_TID_VALID_LOW_PRI_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_TID_VALID_LOW_PRI_M) >> HTT_RX_PEER_MAP_V2_TID_VALID_LOW_PRI_S)

#define HTT_RX_PEER_MAP_V2_AST_INDEX_3_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V2_AST_INDEX_3, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V2_AST_INDEX_3_S; \
    } while (0)
#define HTT_RX_PEER_MAP_V2_AST_INDEX_3_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V2_AST_INDEX_3_M) >> HTT_RX_PEER_MAP_V2_AST_INDEX_3_S)


#define HTT_RX_PEER_MAP_V2_MAC_ADDR_OFFSET       4  /* bytes */
#define HTT_RX_PEER_MAP_V2_HW_PEER_ID_OFFSET     8  /* bytes */
#define HTT_RX_PEER_MAP_V2_AST_HASH_INDEX_OFFSET 12 /* bytes */
#define HTT_RX_PEER_MAP_V2_NEXT_HOP_OFFSET       12 /* bytes */
#define HTT_RX_PEER_MAP_V2_AST_VALID_MASK_OFFSET     12  /* bytes */
#define HTT_RX_PEER_MAP_V2_AST_INDEX_1_OFFSET        16  /* bytes */
#define HTT_RX_PEER_MAP_V2_AST_X_FLOW_MASK_OFFSET    16  /* bytes */
#define HTT_RX_PEER_MAP_V2_AST_INDEX_2_OFFSET        20  /* bytes */
#define HTT_RX_PEER_MAP_V2_TID_VALID_LO_PRI_OFFSET   20  /* bytes */
#define HTT_RX_PEER_MAP_V2_TID_VALID_HI_PRI_OFFSET   20  /* bytes */
#define HTT_RX_PEER_MAP_V2_AST_INDEX_3_OFFSET        24  /* bytes */

#define HTT_RX_PEER_MAP_V2_BYTES 32

/**
 * @brief target -> host rx peer map V3 message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_PEER_MAP_V3
 *
 * @details
 * The following diagram shows the format of the rx peer map v3 message sent
 * from the target to the host.
 * Format inherits HTT_T2H_MSG_TYPE_PEER_MAP_V2 published above
 * This layout assumes the target operates as little-endian.
 *
 * |31             24|23    20|19|18|17|16|15              8|7               0|
 * |-----------------+--------+--+--+--+--+-----------------+-----------------|
 * |              SW peer ID              |     VDEV ID     |     msg type    |
 * |-----------------+--------------------+-----------------+-----------------|
 * |    MAC addr 3   |    MAC addr 2      |    MAC addr 1   |    MAC addr 0   |
 * |-----------------+--------------------+-----------------+-----------------|
 * |          Multicast SW peer ID        |    MAC addr 5   |    MAC addr 4   |
 * |-----------------+--------+-----------+-----------------+-----------------|
 * |  HTT_MSDU_IDX_  |RESERVED|   CACHE_  |                                   |
 * |   VALID_MASK    |(4bits) |  SET_NUM  |      HW peer ID / AST index       |
 * |     (8bits)     |        |  (4bits)  |                                   |
 * |-----------------+--------+--+--+--+--------------------------------------|
 * |        RESERVED             |E |O |  |                                   |
 * |        (13bits)             |A |A |NH|   on-Chip PMAC_RXPCU AST index    |
 * |                             |V |V |  |                                   |
 * |-----------------+--------------------+-----------------------------------|
 * |  HTT_MSDU_IDX_  |      RESERVED      |                                   |
 * | VALID_MASK_EXT  |       (8bits)      |          EXT AST index            |
 * |     (8bits)     |                    |                                   |
 * |-----------------+--------------------+-----------------------------------|
 * |                                  Reserved_2                              |
 * |--------------------------------------------------------------------------|
 * |                                  Reserved_3                              |
 * |--------------------------------------------------------------------------|
 *
 * Where:
 *    EAV = EXT_AST_VALID flag, for "EXT AST index"
 *    OAV = ONCHIP_AST_VALID flag, for "on-Chip PMAC_RXPCU AST index"
 *    NH = Next Hop
 * The following field definitions describe the format of the rx peer map v3
 * messages sent from the target to the host.
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a peer map v3 message
 *     Value: 0x2b (HTT_T2H_MSG_TYPE_PEER_MAP_V3)
 *   - VDEV_ID
 *     Bits 15:8
 *     Purpose: Indicates which virtual device the peer is associated with.
 *   - SW_PEER_ID
 *     Bits 31:16
 *     Purpose: The peer ID (index) that WAL has allocated for this peer.
 *   - MAC_ADDR_L32
 *     Bits 31:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: lower 4 bytes of peer node's MAC address
 *   - MAC_ADDR_U16
 *     Bits 15:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: upper 2 bytes of peer node's MAC address
 *   - MULTICAST_SW_PEER_ID
 *     Bits 31:16
 *     Purpose: The multicast peer ID (index)
 *     Value: set to HTT_INVALID_PEER if not valid
 *   - HW_PEER_ID / AST_INDEX
 *     Bits 15:0
 *     Purpose: Identifies the HW peer ID corresponding to the peer MAC
 *         address, so for rx frames marked for rx --> tx forwarding, the
 *         host can determine from the HW peer ID provided as meta-data with
 *         the rx frame which peer the frame is supposed to be forwarded to.
 *   - CACHE_SET_NUM
 *     Bits 19:16
 *     Purpose:  Cache Set Number for AST_INDEX
 *         Cache set number that should be used to cache the index based
 *         search results, for address and flow search.
 *         This value should be equal to LSB 4 bits of the hash value
 *         of match data, in case of search index points to an entry which
 *         may be used in content based search also. The value can be
 *         anything when the entry pointed by search index will not be
 *         used for content based search.
 *   - HTT_MSDU_IDX_VALID_MASK
 *     Bits 31:24
 *     Purpose: Shows MSDU indexes valid mask for AST_INDEX
 *   - ONCHIP_AST_IDX / RESERVED
 *     Bits 15:0
 *     Purpose: This field is valid only when split AST feature is enabled.
 *         The ONCHIP_AST_VALID flag identifies whether this field is valid.
 *         If valid, identifies the HW peer ID corresponding to the peer MAC
 *         address, this ast_idx is used for LMAC modules for RXPCU.
 *   - NEXT_HOP
 *     Bits 16
 *     Purpose: Flag indicates next_hop AST entry used for WDS
 *              (Wireless Distribution System).
 *   - ONCHIP_AST_VALID
 *     Bits 17
 *     Purpose: Flag indicates valid data behind of the ONCHIP_AST_IDX field
 *   - EXT_AST_VALID
 *     Bits 18
 *     Purpose: Flag indicates valid data behind of the EXT_AST_INDEX field
 *   - EXT_AST_INDEX
 *     Bits 15:0
 *     Purpose: This field describes Extended AST index
 *              Valid if EXT_AST_VALID flag set
 *   - HTT_MSDU_IDX_VALID_MASK_EXT
 *     Bits 31:24
 *     Purpose: Shows MSDU indexes valid mask for EXT_AST_INDEX
*/
/* dword 0 */
#define HTT_RX_PEER_MAP_V3_SW_PEER_ID_M 0xffff0000
#define HTT_RX_PEER_MAP_V3_SW_PEER_ID_S 16
#define HTT_RX_PEER_MAP_V3_VDEV_ID_M    0x0000ff00
#define HTT_RX_PEER_MAP_V3_VDEV_ID_S    8
/* dword 1 */
#define HTT_RX_PEER_MAP_V3_MAC_ADDR_L32_M 0xffffffff
#define HTT_RX_PEER_MAP_V3_MAC_ADDR_L32_S 0
/* dword 2 */
#define HTT_RX_PEER_MAP_V3_MAC_ADDR_U16_M         0x0000ffff
#define HTT_RX_PEER_MAP_V3_MAC_ADDR_U16_S         0
#define HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID_M 0xffff0000
#define HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID_S 16
/* dword 3 */
#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST_M 0xff000000
#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST_S 24
#define HTT_RX_PEER_MAP_V3_CACHE_SET_NUM_M   0x000f0000
#define HTT_RX_PEER_MAP_V3_CACHE_SET_NUM_S   16
#define HTT_RX_PEER_MAP_V3_HW_PEER_ID_M      0x0000ffff
#define HTT_RX_PEER_MAP_V3_HW_PEER_ID_S      0
/* dword 4 */
#define HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG_M         0x00040000
#define HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG_S         18
#define HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG_M      0x00020000
#define HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG_S      17
#define HTT_RX_PEER_MAP_V3_NEXT_HOP_M                   0x00010000
#define HTT_RX_PEER_MAP_V3_NEXT_HOP_S                   16
#define HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX_M 0x0000ffff
#define HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX_S 0
/* dword 5 */
#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST_M 0xff000000
#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST_S 24
#define HTT_RX_PEER_MAP_V3_EXT_AST_IDX_M         0x0000ffff
#define HTT_RX_PEER_MAP_V3_EXT_AST_IDX_S         0

#define HTT_RX_PEER_MAP_V3_VDEV_ID_SET(word, value)           \
    do {                                                      \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_VDEV_ID, value); \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_VDEV_ID_S;   \
    } while (0)
#define HTT_RX_PEER_MAP_V3_VDEV_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_VDEV_ID_M) >> HTT_RX_PEER_MAP_V3_VDEV_ID_S)

#define HTT_RX_PEER_MAP_V3_SW_PEER_ID_SET(word, value)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_SW_PEER_ID, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_SW_PEER_ID_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_SW_PEER_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_SW_PEER_ID_M) >> HTT_RX_PEER_MAP_V3_SW_PEER_ID_S)

#define HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID_SET(word, value)            \
    do {                                                                    \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID_M) >> HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID_S)

#define HTT_RX_PEER_MAP_V3_HW_PEER_ID_SET(word, value)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_HW_PEER_ID, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_HW_PEER_ID_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_HW_PEER_ID_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_HW_PEER_ID_M) >> HTT_RX_PEER_MAP_V3_HW_PEER_ID_S)

#define HTT_RX_PEER_MAP_V3_CACHE_SET_NUM_SET(word, value)            \
    do {                                                             \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_CACHE_SET_NUM, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_CACHE_SET_NUM_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_CACHE_SET_NUM_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_CACHE_SET_NUM_M) >> HTT_RX_PEER_MAP_V3_CACHE_SET_NUM_S)

#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST_SET(word, value)            \
    do {                                                               \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST_M) >> HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST_S)

#define HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX_SET(word, value)            \
    do {                                                                          \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX_M) >> HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX_S)

#define HTT_RX_PEER_MAP_V3_NEXT_HOP_SET(word, value)            \
    do {                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_NEXT_HOP, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_NEXT_HOP_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_NEXT_HOP_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_NEXT_HOP_M) >> HTT_RX_PEER_MAP_V3_NEXT_HOP_S)

#define HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG_SET(word, value)            \
    do {                                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG_M) >> HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG_S)

#define HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG_SET(word, value)            \
    do {                                                                  \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG_M) >> HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG_S)

#define HTT_RX_PEER_MAP_V3_EXT_AST_IDX_SET(word, value)            \
    do {                                                           \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_EXT_AST_IDX, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_EXT_AST_IDX_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_EXT_AST_IDX_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_EXT_AST_IDX_M) >> HTT_RX_PEER_MAP_V3_EXT_AST_IDX_S)

#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST_SET(word, value)            \
    do {                                                                   \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST, value);  \
        (word) |= (value)  << HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST_S;    \
    } while (0)
#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST_GET(word) \
    (((word) & HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST_M) >> HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST_S)

#define HTT_RX_PEER_MAP_V3_MAC_ADDR_OFFSET                   4  /* bytes */
#define HTT_RX_PEER_MAP_V3_MULTICAST_SW_PEER_ID_OFFSET       8  /* bytes */
#define HTT_RX_PEER_MAP_V3_HW_PEER_ID_OFFSET                 12 /* bytes */
#define HTT_RX_PEER_MAP_V3_CACHE_SET_NUM_OFFSET              12 /* bytes */
#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_AST_OFFSET            12 /* bytes */
#define HTT_RX_PEER_MAP_V3_ON_CHIP_PMAC_RXPCU_AST_IDX_OFFSET 16 /* bytes */
#define HTT_RX_PEER_MAP_V3_NEXT_HOP_OFFSET                   16 /* bytes */
#define HTT_RX_PEER_MAP_V3_ONCHIP_AST_VALID_FLAG_OFFSET      16 /* bytes */
#define HTT_RX_PEER_MAP_V3_EXT_AST_VALID_FLAG_OFFSET         16 /* bytes */
#define HTT_RX_PEER_MAP_V3_EXT_AST_IDX_OFFSET                20 /* bytes */
#define HTT_RX_PEER_MAP_V3_MSDU_IDX_VM_EXT_AST_OFFSET        20 /* bytes */

#define HTT_RX_PEER_MAP_V3_BYTES 32

/**
 * @brief target -> host rx peer unmap V2 message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_PEER_UNMAP_V2
 *
 * The following diagram shows the format of the rx peer unmap message sent
 * from the target to the host.
 *
 * |31             24|23             16|15              8|7               0|
 * |-----------------------------------------------------------------------|
 * |            SW peer ID             |     VDEV ID     |     msg type    |
 * |-----------------------------------------------------------------------|
 * |    MAC addr 3   |    MAC addr 2   |    MAC addr 1   |    MAC addr 0   |
 * |-----------------------------------------------------------------------|
 * |    Reserved_17_31     | Next Hop  |    MAC addr 5   |    MAC addr 4   |
 * |-----------------------------------------------------------------------|
 * |                         Peer Delete Duration                          |
 * |-----------------------------------------------------------------------|
 * |               Reserved_0          |           WDS Free Count          |
 * |-----------------------------------------------------------------------|
 * |                               Reserved_1                              |
 * |-----------------------------------------------------------------------|
 * |                               Reserved_2                              |
 * |-----------------------------------------------------------------------|
 *
 *
 * The following field definitions describe the format of the rx peer unmap
 * messages sent from the target to the host.
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx peer unmap v2 message
 *     Value: peer unmap v2 -> 0x1f (HTT_T2H_MSG_TYPE_PEER_UNMAP_V2)
 *   - VDEV_ID
 *     Bits 15:8
 *     Purpose: Indicates which virtual device the peer is associated
 *         with.
 *     Value: vdev ID (used in the host to look up the vdev object)
 *   - SW_PEER_ID
 *     Bits 31:16
 *     Purpose: The peer ID (index) that WAL is freeing
 *     Value: (rx) peer ID
 *   - MAC_ADDR_L32
 *     Bits 31:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: lower 4 bytes of peer node's MAC address
 *   - MAC_ADDR_U16
 *     Bits 15:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: upper 2 bytes of peer node's MAC address
 *   - NEXT_HOP
 *     Bits 16
 *     Purpose: Bit indicates next_hop AST entry used for WDS
 *              (Wireless Distribution System).
 *   - PEER_DELETE_DURATION
 *     Bits 31:0
 *     Purpose: Time taken to delete peer, in msec,
 *         Used for monitoring / debugging PEER delete response delay
 *   - PEER_WDS_FREE_COUNT
 *     Bits 15:0
 *     Purpose: Count of WDS entries deleted associated to peer deleted
 */

#define HTT_RX_PEER_UNMAP_V2_VDEV_ID_M      HTT_RX_PEER_MAP_V2_VDEV_ID_M
#define HTT_RX_PEER_UNMAP_V2_VDEV_ID_S      HTT_RX_PEER_MAP_V2_VDEV_ID_S
#define HTT_RX_PEER_UNMAP_V2_SW_PEER_ID_M   HTT_RX_PEER_MAP_V2_SW_PEER_ID_M
#define HTT_RX_PEER_UNMAP_V2_SW_PEER_ID_S   HTT_RX_PEER_MAP_V2_SW_PEER_ID_S
#define HTT_RX_PEER_UNMAP_V2_MAC_ADDR_L32_M HTT_RX_PEER_MAP_V2_MAC_ADDR_L32_M
#define HTT_RX_PEER_UNMAP_V2_MAC_ADDR_L32_S HTT_RX_PEER_MAP_V2_MAC_ADDR_L32_S
#define HTT_RX_PEER_UNMAP_V2_MAC_ADDR_U16_M HTT_RX_PEER_MAP_V2_MAC_ADDR_U16_M
#define HTT_RX_PEER_UNMAP_V2_MAC_ADDR_U16_S HTT_RX_PEER_MAP_V2_MAC_ADDR_U16_S
#define HTT_RX_PEER_UNMAP_V2_NEXT_HOP_M     HTT_RX_PEER_MAP_V2_NEXT_HOP_M
#define HTT_RX_PEER_UNMAP_V2_NEXT_HOP_S     HTT_RX_PEER_MAP_V2_NEXT_HOP_S

#define HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION_M   0xffffffff
#define HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION_S   0

#define HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT_M    0x0000ffff
#define HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT_S    0

#define HTT_RX_PEER_UNMAP_V2_VDEV_ID_SET    HTT_RX_PEER_MAP_V2_VDEV_ID_SET
#define HTT_RX_PEER_UNMAP_V2_VDEV_ID_GET    HTT_RX_PEER_MAP_V2_VDEV_ID_GET

#define HTT_RX_PEER_UNMAP_V2_SW_PEER_ID_SET HTT_RX_PEER_MAP_V2_SW_PEER_ID_SET
#define HTT_RX_PEER_UNMAP_V2_SW_PEER_ID_GET HTT_RX_PEER_MAP_V2_SW_PEER_ID_GET

#define HTT_RX_PEER_UNMAP_V2_NEXT_HOP_SET   HTT_RX_PEER_MAP_V2_NEXT_HOP_SET
#define HTT_RX_PEER_UNMAP_V2_NEXT_HOP_GET   HTT_RX_PEER_MAP_V2_NEXT_HOP_GET

#define HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION_SET(word, value)           \
    do {                                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION, value); \
        (word) |= (value)  << HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION_S;   \
    } while (0)
#define HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION_GET(word) \
    (((word) & HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION_M) >> HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION_S)

#define HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT, value); \
        (word) |= (value) << HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT_S; \
    } while (0)
#define HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT_GET(word) \
    (((word) & HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT_M) >> HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT_S)

#define HTT_RX_PEER_UNMAP_V2_MAC_ADDR_OFFSET      4  /* bytes */
#define HTT_RX_PEER_UNMAP_V2_NEXT_HOP_OFFSET      8  /* bytes */
#define HTT_RX_PEER_UNMAP_V2_PEER_DELETE_DURATION_OFFSET    12 /* bytes */
#define HTT_RX_PEER_UNMAP_V2_PEER_WDS_FREE_COUNT_OFFSET     16 /* bytes */

#define HTT_RX_PEER_UNMAP_V2_BYTES 28

/**
 * @brief target -> host rx peer mlo map message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP
 *
 * @details
 * The following diagram shows the format of the rx mlo peer map message sent
 * from the target to the host.  This layout assumes the target operates
 * as little-endian.
 *
 * MCC:
 * One HTT_MLO_PEER_MAP is sent after PEER_ASSOC received on first LINK for both STA and SAP.
 *
 * WIN:
 * One HTT_MLO_PEER_MAP is sent after peers are created on all the links for both AP and STA.
 * It will be sent on the Assoc Link.
 *
 * This message always contains a MLO peer ID.  The main purpose of the
 * MLO peer ID is to tell the host what peer ID rx packets will be tagged
 * with, so that the host can use that MLO peer ID to determine which peer
 * transmitted the rx frame.
 *
 * |31   |29  27|26   24|23   20|19 17|16|15              8|7               0|
 * |-------------------------------------------------------------------------|
 * |RSVD | PRC  |NUMLINK|           MLO peer ID            |     msg type    |
 * |-------------------------------------------------------------------------|
 * |    MAC addr 3      |  MAC addr 2    |    MAC addr 1   |    MAC addr 0   |
 * |-------------------------------------------------------------------------|
 * |  RSVD_16_31                         |    MAC addr 5   |    MAC addr 4   |
 * |-------------------------------------------------------------------------|
 * |CACHE_SET_NUM|  TIDMASK     |CHIPID|V|    Primary TCL AST IDX  0         |
 * |-------------------------------------------------------------------------|
 * |CACHE_SET_NUM|  TIDMASK     |CHIPID|V|    Primary TCL AST IDX  1         |
 * |-------------------------------------------------------------------------|
 * |CACHE_SET_NUM|  TIDMASK     |CHIPID|V|    Primary TCL AST IDX  2         |
 * |-------------------------------------------------------------------------|
 * |RSVD                                                                     |
 * |-------------------------------------------------------------------------|
 * |RSVD                                                                     |
 * |-------------------------------------------------------------------------|
 * |    htt_tlv_hdr_t                                                        |
 * |-------------------------------------------------------------------------|
 * |RSVD_27_31   |CHIPID|  VDEVID        |   SW peer ID                      |
 * |-------------------------------------------------------------------------|
 * |    htt_tlv_hdr_t                                                        |
 * |-------------------------------------------------------------------------|
 * |RSVD_27_31   |CHIPID|  VDEVID        |   SW peer ID                      |
 * |-------------------------------------------------------------------------|
 * |    htt_tlv_hdr_t                                                        |
 * |-------------------------------------------------------------------------|
 * |RSVD_27_31   |CHIPID|  VDEVID        |   SW peer ID                      |
 * |-------------------------------------------------------------------------|
 *
 * Where:
 *      PRC - Primary REO CHIPID        - 3 Bits Bit24,25,26
 *      NUMLINK - NUM_LOGICAL_LINKS     - 3 Bits Bit27,28,29
 *      V (valid)                       - 1 Bit  Bit17
 *      CHIPID                          - 3 Bits
 *      TIDMASK                         - 8 Bits
 *      CACHE_SET_NUM                   - 8 Bits
 *
 * The following field definitions describe the format of the rx MLO peer map
 * messages sent from the target to the host.
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx mlo peer map message
 *     Value: 0x29 (HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP)
 *
 *   - MLO_PEER_ID
 *     Bits 23:8
 *     Purpose: The MLO peer ID (index).
 *         For MCC, FW will allocate it. For WIN, Host will allocate it.
 *     Value: MLO peer ID
 *
 *   - NUMLINK
 *     Bits: 26:24  (3Bits)
 *     Purpose: Indicate the max number of logical links supported per client.
 *     Value: number of logical links
 *
 *   - PRC
 *     Bits: 29:27  (3Bits)
 *     Purpose: Indicate the Primary REO CHIPID. The ID can be used to indicate
 *         if there is migration of the primary chip.
 *     Value: Primary REO CHIPID
 *
 *   - MAC_ADDR_L32
 *     Bits 31:0
 *     Purpose: Identifies which mlo peer node the mlo peer ID is for.
 *     Value: lower 4 bytes of peer node's MAC address
 *
 *   - MAC_ADDR_U16
 *     Bits 15:0
 *     Purpose: Identifies which peer node the peer ID is for.
 *     Value: upper 2 bytes of peer node's MAC address
 *
 *   - PRIMARY_TCL_AST_IDX
 *     Bits 15:0
 *     Purpose: Primary TCL AST index for this peer.
 *
 *   - V
 *     1 Bit Position 16
 *     Purpose: If the ast idx is valid.
 *
 *   - CHIPID
 *     Bits 19:17
 *     Purpose: Identifies which chip id of PRIMARY_TCL_AST_IDX
 *
 *   - TIDMASK
 *     Bits 27:20
 *     Purpose: LINK to TID mapping for PRIMARY_TCL_AST_IDX
 *
 *   - CACHE_SET_NUM
 *     Bits 31:28
 *     Purpose:  Cache Set Number for PRIMARY_TCL_AST_IDX
 *         Cache set number that should be used to cache the index based
 *         search results, for address and flow search.
 *         This value should be equal to LSB four bits of the hash value
 *         of match data, in case of search index points to an entry which
 *         may be used in content based search also. The value can be
 *         anything when the entry pointed by search index will not be
 *         used for content based search.
 *
 *   - htt_tlv_hdr_t
 *      Purpose: Provide link specific chip,vdev and sw_peer IDs
 *
 *      Bits 11:0
 *      Purpose: tag equal to MLO_PEER_MAP_TLV_STRUCT_SOC_VDEV_PEER_IDS.
 *
 *      Bits 23:12
 *      Purpose: Length, Length of the value that follows the header
 *
 *      Bits 31:28
 *      Purpose: Reserved.
 *
 *
 *   - SW_PEER_ID
 *     Bits 15:0
 *     Purpose: The peer ID (index) that WAL is allocating
 *     Value: (rx) peer ID
 *
 *   - VDEV_ID
 *     Bits 23:16
 *     Purpose: Indicates which virtual device the peer is associated with.
 *     Value: vdev ID (used in the host to look up the vdev object)
 *
 *   - CHIPID
 *     Bits 26:24
 *     Purpose: Indicates which Chip id the peer is associated with.
 *     Value: chip ID (Provided by Host as part of QMI exchange)
 */
typedef enum {
    MLO_PEER_MAP_TLV_STRUCT_SOC_VDEV_PEER_IDS,
} MLO_PEER_MAP_TLV_TAG_ID;

#define HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_M               0x00ffff00
#define HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_S               8
#define HTT_RX_MLO_PEER_MAP_NUM_LOGICAL_LINKS_M         0x07000000
#define HTT_RX_MLO_PEER_MAP_NUM_LOGICAL_LINKS_S         24
#define HTT_RX_MLO_PEER_PRIMARY_REO_CHIP_ID_M           0x38000000
#define HTT_RX_MLO_PEER_PRIMARY_REO_CHIP_ID_S           27

#define HTT_RX_MLO_PEER_MAP_MAC_ADDR_L32_M              0xffffffff
#define HTT_RX_MLO_PEER_MAP_MAC_ADDR_L32_S              0
#define HTT_RX_MLO_PEER_MAP_MAC_ADDR_U16_M              0x0000ffff
#define HTT_RX_MLO_PEER_MAP_MAC_ADDR_U16_S              0

#define HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_M         0x0000ffff
#define HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_S         0
#define HTT_RX_MLO_PEER_MAP_AST_INDEX_VALID_FLAG_M      0x00010000
#define HTT_RX_MLO_PEER_MAP_AST_INDEX_VALID_FLAG_S      16
#define HTT_RX_MLO_PEER_MAP_CHIP_ID_AST_INDEX_M         0x000E0000
#define HTT_RX_MLO_PEER_MAP_CHIP_ID_AST_INDEX_S         17
#define HTT_RX_MLO_PEER_MAP_TIDMASK_AST_INDEX_M         0x00F00000
#define HTT_RX_MLO_PEER_MAP_TIDMASK_AST_INDEX_S         20
#define HTT_RX_MLO_PEER_MAP_CACHE_SET_NUM_AST_INDEX_M   0xF0000000
#define HTT_RX_MLO_PEER_MAP_CACHE_SET_NUM_AST_INDEX_S   28

#define HTT_RX_MLO_PEER_MAP_TLV_TAG_M                   0x00000fff
#define HTT_RX_MLO_PEER_MAP_TLV_TAG_S                   0
#define HTT_RX_MLO_PEER_MAP_TLV_LENGTH_M                0x00fff000
#define HTT_RX_MLO_PEER_MAP_TLV_LENGTH_S                12

#define HTT_RX_MLO_PEER_MAP_SW_PEER_ID_M                0x0000ffff
#define HTT_RX_MLO_PEER_MAP_SW_PEER_ID_S                0
#define HTT_RX_MLO_PEER_MAP_VDEV_ID_M                   0x00ff0000
#define HTT_RX_MLO_PEER_MAP_VDEV_ID_S                   16
#define HTT_RX_MLO_PEER_MAP_CHIP_ID_M                   0x07000000
#define HTT_RX_MLO_PEER_MAP_CHIP_ID_S                   24


#define HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_SET(word, value)           \
    do {                                                           \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_MLO_PEER_ID, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_M) >> HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_S)

#define HTT_RX_MLO_PEER_MAP_NUM_LOGICAL_LINKS_SET(word, value)           \
    do {                                                                 \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_NUM_LOGICAL_LINKS, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_NUM_LOGICAL_LINKS_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_NUM_LOGICAL_LINKS_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_NUM_LOGICAL_LINKS_M) >> HTT_RX_MLO_PEER_MAP_NUM_LOGICAL_LINKS_S)

#define HTT_RX_MLO_PEER_PRIMARY_REO_CHIP_ID_SET(word, value)           \
    do {                                                               \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_PRIMARY_REO_CHIP_ID, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_PRIMARY_REO_CHIP_ID_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_PRIMARY_REO_CHIP_ID_GET(word) \
    (((word) & HTT_RX_MLO_PEER_PRIMARY_REO_CHIP_ID_M) >> HTT_RX_MLO_PEER_PRIMARY_REO_CHIP_ID_S)

#define HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_SET(word, value)           \
    do {                                                                   \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_M) >> HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_S)

#define HTT_RX_MLO_PEER_MAP_AST_INDEX_VALID_FLAG_SET(word, value)           \
    do {                                                                      \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_AST_INDEX_VALID_FLAG, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_AST_INDEX_VALID_FLAG_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_AST_INDEX_VALID_FLAG_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_AST_INDEX_VALID_FLAG_M) >> HTT_RX_MLO_PEER_MAP_AST_INDEX_VALID_FLAG_S)

#define HTT_RX_MLO_PEER_MAP_CHIP_ID_AST_INDEX_SET(word, value)           \
    do {                                                                   \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_CHIP_ID_AST_INDEX, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_CHIP_ID_AST_INDEX_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_CHIP_ID_AST_INDEX_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_CHIP_ID_AST_INDEX_M) >> HTT_RX_MLO_PEER_MAP_CHIP_ID_AST_INDEX_S)

#define HTT_RX_MLO_PEER_MAP_TIDMASK_AST_INDEX_SET(word, value)           \
    do {                                                                   \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_TIDMASK_AST_INDEX, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_TIDMASK_AST_INDEX_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_TIDMASK_AST_INDEX_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_TIDMASK_AST_INDEX_M) >> HTT_RX_MLO_PEER_MAP_TIDMASK_AST_INDEX_S)

#define HTT_RX_MLO_PEER_MAP_CACHE_SET_NUM_AST_INDEX_SET(word, value)           \
    do {                                                                         \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_CACHE_SET_NUM_AST_INDEX, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_CACHE_SET_NUM_AST_INDEX_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_CACHE_SET_NUM_AST_INDEX_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_CACHE_SET_NUM_AST_INDEX_M) >> HTT_RX_MLO_PEER_MAP_CACHE_SET_NUM_AST_INDEX_S)

#define HTT_RX_MLO_PEER_MAP_TLV_TAG_SET(word, value)           \
    do {                                                        \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_TLV_TAG, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_TLV_TAG_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_TLV_TAG_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_TLV_TAG_M) >> HTT_RX_MLO_PEER_MAP_TLV_TAG_S)

#define HTT_RX_MLO_PEER_MAP_TLV_LENGTH_SET(word, value)           \
    do {                                                           \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_TLV_LENGTH, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_TLV_LENGTH_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_TLV_LENGTH_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_TLV_LENGTH_M) >> HTT_RX_MLO_PEER_MAP_TLV_LENGTH_S)

#define HTT_RX_MLO_PEER_MAP_SW_PEER_ID_SET(word, value)           \
    do {                                                           \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_SW_PEER_ID, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_SW_PEER_ID_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_SW_PEER_ID_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_SW_PEER_ID_M) >> HTT_RX_MLO_PEER_MAP_SW_PEER_ID_S)

#define HTT_RX_MLO_PEER_MAP_VDEV_ID_SET(word, value)           \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_VDEV_ID, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_VDEV_ID_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_VDEV_ID_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_VDEV_ID_M) >> HTT_RX_MLO_PEER_MAP_VDEV_ID_S)

#define HTT_RX_MLO_PEER_MAP_CHIP_ID_SET(word, value)           \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_RX_MLO_PEER_MAP_CHIP_ID, value); \
        (word) |= (value)  << HTT_RX_MLO_PEER_MAP_CHIP_ID_S;   \
    } while (0)
#define HTT_RX_MLO_PEER_MAP_CHIP_ID_GET(word) \
    (((word) & HTT_RX_MLO_PEER_MAP_CHIP_ID_M) >> HTT_RX_MLO_PEER_MAP_CHIP_ID_S)


#define HTT_RX_MLO_PEER_MAP_MAC_ADDR_OFFSET                  4  /* bytes */
#define HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_0_OFFSET      12  /* bytes */
#define HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_1_OFFSET      16  /* bytes */
#define HTT_RX_MLO_PEER_MAP_PRIMARY_AST_INDEX_2_OFFSET      20  /* bytes */
#define HTT_RX_MLO_PEER_MAP_TLV_OFFSET                      32  /* bytes */

#define HTT_RX_MLO_PEER_MAP_FIXED_BYTES 8*4 /* 8 Dwords. Does not include the TLV header and the TLV */


/* MSG_TYPE => HTT_T2H_MSG_TYPE_MLO_RX_PEER_UNMAP
*
* The following diagram shows the format of the rx mlo peer unmap message sent
* from the target to the host.
*
* |31             24|23             16|15              8|7               0|
* |-----------------------------------------------------------------------|
* | RSVD_24_31      |     MLO peer ID                   |     msg type    |
* |-----------------------------------------------------------------------|
*/

#define HTT_RX_MLO_PEER_UNMAP_MLO_PEER_ID_M      HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_M
#define HTT_RX_MLO_PEER_UNMAP_MLO_PEER_ID_S      HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_S

#define HTT_RX_MLO_PEER_UNMAP_MLO_PEER_ID_SET    HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_SET
#define HTT_RX_MLO_PEER_UNMAP_MLO_PEER_ID_GET    HTT_RX_MLO_PEER_MAP_MLO_PEER_ID_GET

/**
 * @brief target -> host message specifying security parameters
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_SEC_IND
 *
 * @details
 *  The following diagram shows the format of the security specification
 *  message sent from the target to the host.
 *  This security specification message tells the host whether a PN check is
 *  necessary on rx data frames, and if so, how large the PN counter is.
 *  This message also tells the host about the security processing to apply
 *  to defragmented rx frames - specifically, whether a Message Integrity
 *  Check is required, and the Michael key to use.
 *
 * |31             24|23          16|15|14              8|7               0|
 * |-----------------------------------------------------------------------|
 * |              peer ID           | U|  security type  |     msg type    |
 * |-----------------------------------------------------------------------|
 * |                           Michael Key K0                              |
 * |-----------------------------------------------------------------------|
 * |                           Michael Key K1                              |
 * |-----------------------------------------------------------------------|
 * |                           WAPI RSC Low0                               |
 * |-----------------------------------------------------------------------|
 * |                           WAPI RSC Low1                               |
 * |-----------------------------------------------------------------------|
 * |                           WAPI RSC Hi0                                |
 * |-----------------------------------------------------------------------|
 * |                           WAPI RSC Hi1                                |
 * |-----------------------------------------------------------------------|
 *
 * The following field definitions describe the format of the security
 * indication message sent from the target to the host.
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a security specification message
 *     Value: 0xb (HTT_T2H_MSG_TYPE_SEC_IND)
 *   - SEC_TYPE
 *     Bits 14:8
 *     Purpose: specifies which type of security applies to the peer
 *     Value: htt_sec_type enum value
 *   - UNICAST
 *     Bit 15
 *     Purpose: whether this security is applied to unicast or multicast data
 *     Value: 1 -> unicast, 0 -> multicast
 *   - PEER_ID
 *     Bits 31:16
 *     Purpose: The ID number for the peer the security specification is for
 *     Value: peer ID
 *   - MICHAEL_KEY_K0
 *     Bits 31:0
 *     Purpose: 4-byte word that forms the 1st half of the TKIP Michael key
 *     Value: Michael Key K0 (if security type is TKIP)
 *   - MICHAEL_KEY_K1
 *     Bits 31:0
 *     Purpose: 4-byte word that forms the 2nd half of the TKIP Michael key
 *     Value: Michael Key K1 (if security type is TKIP)
 *   - WAPI_RSC_LOW0
 *     Bits 31:0
 *     Purpose: 4-byte word that forms the 1st quarter of the 16 byte WAPI RSC
 *     Value: WAPI RSC Low0 (if security type is WAPI)
 *   - WAPI_RSC_LOW1
 *     Bits 31:0
 *     Purpose: 4-byte word that forms the 2nd quarter of the 16 byte WAPI RSC
 *     Value: WAPI RSC Low1 (if security type is WAPI)
 *   - WAPI_RSC_HI0
 *     Bits 31:0
 *     Purpose: 4-byte word that forms the 3rd quarter of the 16 byte WAPI RSC
 *     Value: WAPI RSC Hi0 (if security type is WAPI)
 *   - WAPI_RSC_HI1
 *     Bits 31:0
 *     Purpose: 4-byte word that forms the 4th quarter of the 16 byte WAPI RSC
 *     Value: WAPI RSC Hi1 (if security type is WAPI)
 */

#define HTT_SEC_IND_SEC_TYPE_M     0x00007f00
#define HTT_SEC_IND_SEC_TYPE_S     8
#define HTT_SEC_IND_UNICAST_M      0x00008000
#define HTT_SEC_IND_UNICAST_S      15
#define HTT_SEC_IND_PEER_ID_M      0xffff0000
#define HTT_SEC_IND_PEER_ID_S      16

#define HTT_SEC_IND_SEC_TYPE_SET(word, value)                       \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_SEC_IND_SEC_TYPE, value);             \
        (word) |= (value)  << HTT_SEC_IND_SEC_TYPE_S;               \
    } while (0)
#define HTT_SEC_IND_SEC_TYPE_GET(word) \
    (((word) & HTT_SEC_IND_SEC_TYPE_M) >> HTT_SEC_IND_SEC_TYPE_S)

#define HTT_SEC_IND_UNICAST_SET(word, value)                        \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_SEC_IND_UNICAST, value);              \
        (word) |= (value)  << HTT_SEC_IND_UNICAST_S;                \
    } while (0)
#define HTT_SEC_IND_UNICAST_GET(word) \
    (((word) & HTT_SEC_IND_UNICAST_M) >> HTT_SEC_IND_UNICAST_S)

#define HTT_SEC_IND_PEER_ID_SET(word, value)                        \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_SEC_IND_PEER_ID, value);              \
        (word) |= (value)  << HTT_SEC_IND_PEER_ID_S;                \
    } while (0)
#define HTT_SEC_IND_PEER_ID_GET(word) \
    (((word) & HTT_SEC_IND_PEER_ID_M) >> HTT_SEC_IND_PEER_ID_S)


#define HTT_SEC_IND_BYTES 28


/**
 * @brief target -> host rx ADDBA / DELBA message definitions
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_ADDBA
 *
 * @details
 * The following diagram shows the format of the rx ADDBA message sent
 * from the target to the host:
 *
 * |31                      20|19  16|15              8|7               0|
 * |---------------------------------------------------------------------|
 * |          peer ID         |  TID |   window size   |     msg type    |
 * |---------------------------------------------------------------------|
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_DELBA
 *
 * The following diagram shows the format of the rx DELBA message sent
 * from the target to the host:
 *
 * |31                      20|19  16|15         10|9 8|7               0|
 * |---------------------------------------------------------------------|
 * |          peer ID         |  TID | window size | IR|     msg type    |
 * |---------------------------------------------------------------------|
 *
 * The following field definitions describe the format of the rx ADDBA
 * and DELBA messages sent from the target to the host.
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx ADDBA or DELBA message
 *     Value: ADDBA -> 0x5 (HTT_T2H_MSG_TYPE_RX_ADDBA),
 *            DELBA -> 0x6 (HTT_T2H_MSG_TYPE_RX_DELBA)
 *   - IR (initiator / recipient)
 *     Bits 9:8 (DELBA only)
 *     Purpose: specify whether the DELBA handshake was initiated by the
 *         local STA/AP, or by the peer STA/AP
 *     Value:
 *         0 - unspecified
 *         1 - initiator (a.k.a. originator)
 *         2 - recipient (a.k.a. responder)
 *         3 - unused / reserved
 *   - WIN_SIZE
 *     Bits 15:8 for ADDBA, bits 15:10 for DELBA
 *     Purpose: Specifies the length of the block ack window (max = 64).
 *     Value:
 *         block ack window length specified by the received ADDBA/DELBA
 *         management message.
 *   - TID
 *     Bits 19:16
 *     Purpose: Specifies which traffic identifier the ADDBA / DELBA is for.
 *     Value:
 *         TID specified by the received ADDBA or DELBA management message.
 *   - PEER_ID
 *     Bits 31:20
 *     Purpose: Identifies which peer sent the ADDBA / DELBA.
 *     Value:
 *         ID (hash value) used by the host for fast,  direct lookup of
 *         host SW peer info, including rx reorder states.
 */
#define HTT_RX_ADDBA_WIN_SIZE_M  0xff00
#define HTT_RX_ADDBA_WIN_SIZE_S  8
#define HTT_RX_ADDBA_TID_M       0xf0000
#define HTT_RX_ADDBA_TID_S       16
#define HTT_RX_ADDBA_PEER_ID_M   0xfff00000
#define HTT_RX_ADDBA_PEER_ID_S   20

#define HTT_RX_ADDBA_WIN_SIZE_SET(word, value)                          \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_ADDBA_WIN_SIZE, value);                \
        (word) |= (value)  << HTT_RX_ADDBA_WIN_SIZE_S;                  \
    } while (0)
#define HTT_RX_ADDBA_WIN_SIZE_GET(word) \
    (((word) & HTT_RX_ADDBA_WIN_SIZE_M) >> HTT_RX_ADDBA_WIN_SIZE_S)

#define HTT_RX_ADDBA_TID_SET(word, value)                               \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_ADDBA_TID, value);                     \
        (word) |= (value)  << HTT_RX_ADDBA_TID_S;                       \
    } while (0)
#define HTT_RX_ADDBA_TID_GET(word) \
    (((word) & HTT_RX_ADDBA_TID_M) >> HTT_RX_ADDBA_TID_S)

#define HTT_RX_ADDBA_PEER_ID_SET(word, value)                           \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_ADDBA_PEER_ID, value);                 \
        (word) |= (value)  << HTT_RX_ADDBA_PEER_ID_S;                   \
    } while (0)
#define HTT_RX_ADDBA_PEER_ID_GET(word) \
    (((word) & HTT_RX_ADDBA_PEER_ID_M) >> HTT_RX_ADDBA_PEER_ID_S)

#define HTT_RX_ADDBA_BYTES 4


#define HTT_RX_DELBA_INITIATOR_M   0x00000300
#define HTT_RX_DELBA_INITIATOR_S   8
#define HTT_RX_DELBA_WIN_SIZE_M    0x0000FC00
#define HTT_RX_DELBA_WIN_SIZE_S    10
#define HTT_RX_DELBA_TID_M         HTT_RX_ADDBA_TID_M
#define HTT_RX_DELBA_TID_S         HTT_RX_ADDBA_TID_S
#define HTT_RX_DELBA_PEER_ID_M     HTT_RX_ADDBA_PEER_ID_M
#define HTT_RX_DELBA_PEER_ID_S     HTT_RX_ADDBA_PEER_ID_S

#define HTT_RX_DELBA_TID_SET       HTT_RX_ADDBA_TID_SET
#define HTT_RX_DELBA_TID_GET       HTT_RX_ADDBA_TID_GET
#define HTT_RX_DELBA_PEER_ID_SET   HTT_RX_ADDBA_PEER_ID_SET
#define HTT_RX_DELBA_PEER_ID_GET   HTT_RX_ADDBA_PEER_ID_GET

#define HTT_RX_DELBA_INITIATOR_SET(word, value)                    \
    do {                                                           \
        HTT_CHECK_SET_VAL(HTT_RX_DELBA_INITIATOR, value);          \
        (word) |= (value)  << HTT_RX_DELBA_INITIATOR_S;            \
    } while (0)
#define HTT_RX_DELBA_INITIATOR_GET(word) \
    (((word) & HTT_RX_DELBA_INITIATOR_M) >> HTT_RX_DELBA_INITIATOR_S)

#define HTT_RX_DELBA_WIN_SIZE_SET(word, value)                     \
    do {                                                           \
        HTT_CHECK_SET_VAL(HTT_RX_DELBA_WIN_SIZE, value);           \
        (word) |= (value)  << HTT_RX_DELBA_WIN_SIZE_S;             \
    } while (0)
#define HTT_RX_DELBA_WIN_SIZE_GET(word) \
    (((word) & HTT_RX_DELBA_WIN_SIZE_M) >> HTT_RX_DELBA_WIN_SIZE_S)

#define HTT_RX_DELBA_BYTES 4

/**
 * @brief tx queue group information element definition
 *
 * @details
 * The following diagram shows the format of the tx queue group
 * information element, which can be included in target --> host
 * messages to specify the number of tx "credits" (tx descriptors
 * for LL, or tx buffers for HL) available to a particular group
 * of host-side tx queues, and which host-side tx queues belong to
 * the group.
 *
 * |31|30          24|23             16|15|14|13                           0|
 * |------------------------------------------------------------------------|
 * | X|   reserved   | tx queue grp ID | A| S|     credit count             |
 * |------------------------------------------------------------------------|
 * |            vdev ID mask           |               AC mask              |
 * |------------------------------------------------------------------------|
 *
 * The following definitions describe the fields within the tx queue group
 * information element:
 * - credit_count
 *   Bits 13:1
 *   Purpose: specify how many tx credits are available to the tx queue group
 *   Value: An absolute or relative, positive or negative credit value
 *       The 'A' bit specifies whether the value is absolute or relative.
 *       The 'S' bit specifies whether the value is positive or negative.
 *       A negative value can only be relative, not absolute.
 *       An absolute value replaces any prior credit value the host has for
 *       the tx queue group in question.
 *       A relative value is added to the prior credit value the host has for
 *       the tx queue group in question.
 * - sign
 *   Bit 14
 *   Purpose: specify whether the credit count is positive or negative
 *   Value: 0 -> positive, 1 -> negative
 * - absolute
 *   Bit 15
 *   Purpose: specify whether the credit count is absolute or relative
 *   Value: 0 -> relative, 1 -> absolute
 * - txq_group_id
 *   Bits 23:16
 *   Purpose: indicate which tx queue group's credit and/or membership are
 *       being specified
 *   Value: 0 to max_tx_queue_groups-1
 * - reserved
 *   Bits 30:16
 *   Value: 0x0
 * - eXtension
 *   Bit 31
 *   Purpose: specify whether another tx queue group info element follows
 *   Value: 0 -> no more tx queue group information elements
 *          1 -> another tx queue group information element immediately follows
 * - ac_mask
 *   Bits 15:0
 *   Purpose: specify which Access Categories belong to the tx queue group
 *   Value: bit-OR of masks for the ACs (WMM and extension) that belong to
 *       the tx queue group.
 *       The AC bit-mask values are obtained by left-shifting by the
 *       corresponding HTT_AC_WMM enum values, e.g. (1 << HTT_AC_WMM_BE) == 0x1
 * - vdev_id_mask
 *   Bits 31:16
 *   Purpose: specify which vdev's tx queues belong to the tx queue group
 *   Value: bit-OR of masks based on the IDs of the vdevs whose tx queues
 *       belong to the tx queue group.
 *       For example, if vdev IDs 1 and 4 belong to a tx queue group, the
 *       vdev_id_mask would be (1 << 1) | (1 << 4) = 0x12
 */
PREPACK struct htt_txq_group {
    A_UINT32
        credit_count:      14,
        sign:               1,
        absolute:           1,
        tx_queue_group_id:  8,
        reserved0:          7,
        extension:          1;
    A_UINT32
        ac_mask:           16,
        vdev_id_mask:      16;
} POSTPACK;

/* first word */
#define HTT_TXQ_GROUP_CREDIT_COUNT_S 0
#define HTT_TXQ_GROUP_CREDIT_COUNT_M 0x00003fff
#define HTT_TXQ_GROUP_SIGN_S         14
#define HTT_TXQ_GROUP_SIGN_M         0x00004000
#define HTT_TXQ_GROUP_ABS_S          15
#define HTT_TXQ_GROUP_ABS_M          0x00008000
#define HTT_TXQ_GROUP_ID_S           16
#define HTT_TXQ_GROUP_ID_M           0x00ff0000
#define HTT_TXQ_GROUP_EXT_S          31
#define HTT_TXQ_GROUP_EXT_M          0x80000000
/* second word */
#define HTT_TXQ_GROUP_AC_MASK_S      0
#define HTT_TXQ_GROUP_AC_MASK_M      0x0000ffff
#define HTT_TXQ_GROUP_VDEV_ID_MASK_S 16
#define HTT_TXQ_GROUP_VDEV_ID_MASK_M 0xffff0000

#define HTT_TXQ_GROUP_CREDIT_COUNT_SET(_info, _val)            \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_TXQ_GROUP_CREDIT_COUNT, _val);   \
        ((_info) |= ((_val) << HTT_TXQ_GROUP_CREDIT_COUNT_S)); \
    } while (0)
#define HTT_TXQ_GROUP_CREDIT_COUNT_GET(_info)                  \
    (((_info) & HTT_TXQ_GROUP_CREDIT_COUNT_M) >> HTT_TXQ_GROUP_CREDIT_COUNT_S)

#define HTT_TXQ_GROUP_SIGN_SET(_info, _val)                    \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_TXQ_GROUP_SIGN, _val);           \
        ((_info) |= ((_val) << HTT_TXQ_GROUP_SIGN_S));         \
    } while (0)
#define HTT_TXQ_GROUP_SIGN_GET(_info)                          \
    (((_info) & HTT_TXQ_GROUP_SIGN_M) >> HTT_TXQ_GROUP_SIGN_S)

#define HTT_TXQ_GROUP_ABS_SET(_info, _val)                     \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_TXQ_GROUP_ABS, _val);            \
        ((_info) |= ((_val) << HTT_TXQ_GROUP_ABS_S));          \
    } while (0)
#define HTT_TXQ_GROUP_ABS_GET(_info)                           \
    (((_info) & HTT_TXQ_GROUP_ABS_M) >> HTT_TXQ_GROUP_ABS_S)

#define HTT_TXQ_GROUP_ID_SET(_info, _val)                      \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_TXQ_GROUP_ID, _val);             \
        ((_info) |= ((_val) << HTT_TXQ_GROUP_ID_S));           \
    } while (0)
#define HTT_TXQ_GROUP_ID_GET(_info)                            \
    (((_info) & HTT_TXQ_GROUP_ID_M) >> HTT_TXQ_GROUP_ID_S)

#define HTT_TXQ_GROUP_EXT_SET(_info, _val)                     \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_TXQ_GROUP_EXT, _val);            \
        ((_info) |= ((_val) << HTT_TXQ_GROUP_EXT_S));          \
    } while (0)
#define HTT_TXQ_GROUP_EXT_GET(_info)                           \
    (((_info) & HTT_TXQ_GROUP_EXT_M) >> HTT_TXQ_GROUP_EXT_S)

#define HTT_TXQ_GROUP_AC_MASK_SET(_info, _val)                 \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_TXQ_GROUP_AC_MASK, _val);        \
        ((_info) |= ((_val) << HTT_TXQ_GROUP_AC_MASK_S));      \
    } while (0)
#define HTT_TXQ_GROUP_AC_MASK_GET(_info)                       \
    (((_info) & HTT_TXQ_GROUP_AC_MASK_M) >> HTT_TXQ_GROUP_AC_MASK_S)

#define HTT_TXQ_GROUP_VDEV_ID_MASK_SET(_info, _val)            \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_TXQ_GROUP_VDEV_ID_MASK, _val);   \
        ((_info) |= ((_val) << HTT_TXQ_GROUP_VDEV_ID_MASK_S)); \
    } while (0)
#define HTT_TXQ_GROUP_VDEV_ID_MASK_GET(_info)                  \
    (((_info) & HTT_TXQ_GROUP_VDEV_ID_MASK_M) >> HTT_TXQ_GROUP_VDEV_ID_MASK_S)

/**
 * @brief target -> host TX completion indication message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_TX_COMPL_IND
 *
 * @details
 * The following diagram shows the format of the TX completion indication sent
 * from the target to the host
 *
 *         |31 30|29|28|27|26|25|24|23        16| 15 |14 11|10   8|7          0|
 *         |-------------------------------------------------------------------|
 * header: |rsvd |A4|A3|A2|TP|A1|A0|     num    | t_i| tid |status|  msg_type  |
 *         |-------------------------------------------------------------------|
 * payload:|            MSDU1 ID                |         MSDU0 ID             |
 *         |-------------------------------------------------------------------|
 *         :            MSDU3 ID                |         MSDU2 ID             :
 *         |-------------------------------------------------------------------|
 *         |               struct htt_tx_compl_ind_append_retries              |
 *         |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -|
 *         |               struct htt_tx_compl_ind_append_tx_tstamp            |
 *         |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -|
 *         |           MSDU1 ACK RSSI           |        MSDU0 ACK RSSI        |
 *         |-------------------------------------------------------------------|
 *         :           MSDU3 ACK RSSI           |        MSDU2 ACK RSSI        :
 *         |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -|
 *         |                          MSDU0 tx_tsf64_low                       |
 *         |-------------------------------------------------------------------|
 *         |                          MSDU0 tx_tsf64_high                      |
 *         |-------------------------------------------------------------------|
 *         |                          MSDU1 tx_tsf64_low                       |
 *         |-------------------------------------------------------------------|
 *         |                          MSDU1 tx_tsf64_high                      |
 *         |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -|
 *         |                            phy_timestamp                          |
 *         |-------------------------------------------------------------------|
 *         |                        rate specs (see below)                     |
 *         |-------------------------------------------------------------------|
 *         |               seqctrl              |          framectrl           |
 *         |- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -|
 * Where:
 *     A0 = append (a.k.a. append0)
 *     A1 = append1
 *     TP = MSDU tx power presence
 *     A2 = append2
 *     A3 = append3
 *     A4 = append4
 *
 * The following field definitions describe the format of the TX completion
 * indication sent from the target to the host
 * Header fields:
 * - msg_type
 *   Bits 7:0
 *   Purpose: identifies this as HTT TX completion indication
 *   Value: 0x7 (HTT_T2H_MSG_TYPE_TX_COMPL_IND)
 * - status
 *   Bits 10:8
 *   Purpose: the TX completion status of payload fragmentations descriptors
 *   Value: could be HTT_TX_COMPL_IND_STAT_OK or HTT_TX_COMPL_IND_STAT_DISCARD
 * - tid
 *   Bits 14:11
 *   Purpose: the tid associated with those fragmentation descriptors. It is
 *            valid or not, depending on the tid_invalid bit.
 *   Value: 0 to 15
 * - tid_invalid
 *   Bits 15:15
 *   Purpose: this bit indicates whether the tid field is valid or not
 *   Value: 0 indicates valid; 1 indicates invalid
 * - num
 *   Bits 23:16
 *   Purpose: the number of payload in this indication
 *   Value: 1 to 255
 * - append (a.k.a. append0)
 *   Bits 24:24
 *   Purpose: append the struct htt_tx_compl_ind_append_retries which contains
 *            the number of tx retries for one MSDU at the end of this message
 *   Value: 0 indicates no appending; 1 indicates appending
 * - append1
 *   Bits 25:25
 *   Purpose: Append the struct htt_tx_compl_ind_append_tx_tstamp which
 *            contains the timestamp info for each TX msdu id in payload.
 *            The order of the timestamps matches the order of the MSDU IDs.
 *            Note that a big-endian host needs to account for the reordering
 *            of MSDU IDs within each 4-byte MSDU ID pair (during endianness
 *            conversion) when determining which tx timestamp corresponds to
 *            which MSDU ID.
 *   Value: 0 indicates no appending; 1 indicates appending
 * - msdu_tx_power_presence
 *   Bits 26:26
 *   Purpose: Indicate whether the TX_COMPL_IND includes a tx power report
 *            for each MSDU referenced by the TX_COMPL_IND message.
 *            The tx power is reported in 0.5 dBm units.
 *            The order of the per-MSDU tx power reports matches the order
 *            of the MSDU IDs.
 *            Note that a big-endian host needs to account for the reordering
 *            of MSDU IDs within each 4-byte MSDU ID pair (during endianness
 *            conversion) when determining which Tx Power corresponds to
 *            which MSDU ID.
 *   Value: 0 indicates MSDU tx power reports are not appended,
 *          1 indicates MSDU tx power reports are appended
 * - append2
 *   Bits 27:27
 *   Purpose: Indicate whether data ACK RSSI is appended for each MSDU in
 *            TX_COMP_IND message.  The order of the per-MSDU ACK RSSI report
 *            matches the order of the MSDU IDs.  Although the ACK RSSI is the
 *            same for all MSDUs witin a single PPDU, the RSSI is duplicated
 *            for each MSDU, for convenience.
 *            The ACK RSSI values are valid when status is COMPLETE_OK (and
 *            this append2 bit is set).
 *            The ACK RSSI values are SNR in dB, i.e. are the RSSI in units of
 *            dB above the noise floor.
 *   Value: 0 indicates MSDU ACK RSSI values are not appended,
 *          1 indicates MSDU ACK RSSI values are appended.
 * - append3
 *   Bits 28:28
 *   Purpose: Append the struct htt_tx_compl_ind_append_tx_tsf64 which
 *            contains the tx tsf info based on wlan global TSF for
 *            each TX msdu id in payload.
 *            The order of the tx tsf matches the order of the MSDU IDs.
 *            The struct htt_tx_compl_ind_append_tx_tsf64 contains two 32-bits
 *            values to indicate the the lower 32 bits and higher 32 bits of
 *            the tx tsf.
 *            The tx_tsf64 here represents the time MSDU was acked and the
 *            tx_tsf64 has microseconds units.
 *   Value: 0 indicates no appending; 1 indicates appending
 * - append4
 *   Bits 29:29
 *   Purpose: Indicate whether data frame control fields and fields required
 *            for radio tap header are appended for each MSDU in TX_COMP_IND
 *            message.  The order of the this message matches the order of
 *            the MSDU IDs.
 *   Value: 0 indicates frame control fields and fields required for
 *            radio tap header values are not appended,
 *          1 indicates frame control fields and fields required for
 *            radio tap header values are appended.
 * Payload fields:
 * - hmsdu_id
 *   Bits 15:0
 *   Purpose: this ID is used to track the Tx buffer in host
 *   Value: 0 to "size of host MSDU descriptor pool - 1"
 */

PREPACK struct htt_tx_data_hdr_information {
    A_UINT32 phy_timestamp_l32; /* word 0 [31:0] */
    A_UINT32  /* word 1 */
        /* preamble:
         * 0-OFDM,
         * 1-CCk,
         * 2-HT,
         * 3-VHT
         */
        preamble: 2, /* [1:0] */
        /* mcs:
         * In case of HT preamble interpret
         * MCS along with NSS.
         * Valid values for HT are 0 to 7.
         * HT mcs 0 with NSS 2 is mcs 8.
         * Valid values for VHT are 0 to 9.
         */
        mcs:      4, /* [5:2] */
        /* rate:
         * This is applicable only for
         * CCK and OFDM preamble type
         * rate 0: OFDM 48 Mbps,
         *      1: OFDM 24 Mbps,
         *      2: OFDM 12 Mbps
         *      3: OFDM 6  Mbps
         *      4: OFDM 54 Mbps
         *      5: OFDM 36 Mbps
         *      6: OFDM 18 Mbps
         *      7: OFDM 9  Mbps
         * rate 0: CCK 11 Mbps Long
         *      1: CCK 5.5 Mbps Long
         *      2: CCK 2 Mbps Long
         *      3: CCK 1 Mbps Long
         *      4: CCK 11 Mbps Short
         *      5: CCK 5.5 Mbps Short
         *      6: CCK 2 Mbps Short
         */
        rate    : 3, /* [ 8: 6] */
        rssi    : 8, /* [16: 9] units=dBm */
        nss     : 2, /* [18:17] if nss 1 means 1ss and 2 means 2ss */
        bw      : 3, /* [21:19] (0=>20MHz, 1=>40MHz, 2=>80MHz, 3=>160MHz) */
        stbc    : 1, /* [22] */
        sgi     : 1, /* [23] */
        ldpc    : 1, /* [24] */
        beamformed: 1, /* [25] */
        /* tx_retry_cnt:
         * Indicates retry count of data tx frames provided by the host.
         */
        tx_retry_cnt: 6; /* [31:26] */
    A_UINT32 /* word 2 */
        framectrl:16, /* [15: 0] */
        seqno:16;     /* [31:16] */
} POSTPACK;


#define HTT_TX_COMPL_IND_STATUS_S      8
#define HTT_TX_COMPL_IND_STATUS_M      0x00000700
#define HTT_TX_COMPL_IND_TID_S         11
#define HTT_TX_COMPL_IND_TID_M         0x00007800
#define HTT_TX_COMPL_IND_TID_INV_S     15
#define HTT_TX_COMPL_IND_TID_INV_M     0x00008000
#define HTT_TX_COMPL_IND_NUM_S         16
#define HTT_TX_COMPL_IND_NUM_M         0x00ff0000
#define HTT_TX_COMPL_IND_APPEND_S      24
#define HTT_TX_COMPL_IND_APPEND_M      0x01000000
#define HTT_TX_COMPL_IND_APPEND1_S     25
#define HTT_TX_COMPL_IND_APPEND1_M     0x02000000
#define HTT_TX_COMPL_IND_TX_POWER_S    26
#define HTT_TX_COMPL_IND_TX_POWER_M    0x04000000
#define HTT_TX_COMPL_IND_APPEND2_S     27
#define HTT_TX_COMPL_IND_APPEND2_M     0x08000000
#define HTT_TX_COMPL_IND_APPEND3_S     28
#define HTT_TX_COMPL_IND_APPEND3_M     0x10000000
#define HTT_TX_COMPL_IND_APPEND4_S     29
#define HTT_TX_COMPL_IND_APPEND4_M     0x20000000

#define HTT_TX_COMPL_IND_STATUS_SET(_info, _val)                        \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_STATUS, _val);               \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_STATUS_S));             \
    } while (0)
#define HTT_TX_COMPL_IND_STATUS_GET(_info)                              \
    (((_info) & HTT_TX_COMPL_IND_STATUS_M) >> HTT_TX_COMPL_IND_STATUS_S)
#define HTT_TX_COMPL_IND_NUM_SET(_info, _val)                           \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_NUM, _val);                  \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_NUM_S));                \
    } while (0)
#define HTT_TX_COMPL_IND_NUM_GET(_info)                             \
    (((_info) & HTT_TX_COMPL_IND_NUM_M) >> HTT_TX_COMPL_IND_NUM_S)
#define HTT_TX_COMPL_IND_TID_SET(_info, _val)                           \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_TID, _val);                  \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_TID_S));                \
    } while (0)
#define HTT_TX_COMPL_IND_TID_GET(_info)                             \
    (((_info) & HTT_TX_COMPL_IND_TID_M) >> HTT_TX_COMPL_IND_TID_S)
#define HTT_TX_COMPL_IND_TID_INV_SET(_info, _val)                       \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_TID_INV, _val);              \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_TID_INV_S));            \
    } while (0)
#define HTT_TX_COMPL_IND_TID_INV_GET(_info)                         \
    (((_info) & HTT_TX_COMPL_IND_TID_INV_M) >>                      \
     HTT_TX_COMPL_IND_TID_INV_S)
#define HTT_TX_COMPL_IND_APPEND_SET(_info, _val)                           \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_APPEND, _val);                  \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_APPEND_S));                \
    } while (0)
#define HTT_TX_COMPL_IND_APPEND_GET(_info)                             \
    (((_info) & HTT_TX_COMPL_IND_APPEND_M) >> HTT_TX_COMPL_IND_APPEND_S)
#define HTT_TX_COMPL_IND_APPEND1_SET(_info, _val)                      \
    do {                                                               \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_APPEND1, _val);             \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_APPEND1_S));           \
    } while (0)
#define HTT_TX_COMPL_IND_APPEND1_GET(_info)                            \
    (((_info) & HTT_TX_COMPL_IND_APPEND1_M) >> HTT_TX_COMPL_IND_APPEND1_S)
#define HTT_TX_COMPL_IND_TX_POWER_SET(_info, _val)                           \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_TX_POWER, _val);                \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_TX_POWER_S));              \
    } while (0)
#define HTT_TX_COMPL_IND_TX_POWER_GET(_info)                             \
    (((_info) & HTT_TX_COMPL_IND_TX_POWER_M) >> HTT_TX_COMPL_IND_TX_POWER_S)
#define HTT_TX_COMPL_IND_APPEND2_SET(_info, _val)                      \
    do {                                                               \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_APPEND2, _val);             \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_APPEND2_S));           \
    } while (0)
#define HTT_TX_COMPL_IND_APPEND2_GET(_info)                            \
    (((_info) & HTT_TX_COMPL_IND_APPEND2_M) >> HTT_TX_COMPL_IND_APPEND2_S)
#define HTT_TX_COMPL_IND_APPEND3_SET(_info, _val)                      \
    do {                                                               \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_APPEND3, _val);             \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_APPEND3_S));           \
    } while (0)
#define HTT_TX_COMPL_IND_APPEND3_GET(_info)                            \
    (((_info) & HTT_TX_COMPL_IND_APPEND3_M) >> HTT_TX_COMPL_IND_APPEND3_S)
#define HTT_TX_COMPL_IND_APPEND4_SET(_info, _val)                      \
    do {                                                               \
        HTT_CHECK_SET_VAL(HTT_TX_COMPL_IND_APPEND4, _val);             \
        ((_info) |= ((_val) << HTT_TX_COMPL_IND_APPEND4_S));           \
    } while (0)
#define HTT_TX_COMPL_IND_APPEND4_GET(_info)                            \
    (((_info) & HTT_TX_COMPL_IND_APPEND4_M) >> HTT_TX_COMPL_IND_APPEND4_S)

#define HTT_TX_COMPL_INV_TX_POWER           0xffff

#define HTT_TX_COMPL_CTXT_SZ                sizeof(A_UINT16)
#define HTT_TX_COMPL_CTXT_NUM(_bytes)       ((_bytes) >> 1)

#define HTT_TX_COMPL_INV_MSDU_ID            0xffff

#define HTT_TX_COMPL_IND_STAT_OK            0
/* DISCARD:
 * current meaning:
 *     MSDUs were queued for transmission but filtered by HW or SW
 *     without any over the air attempts
 * legacy meaning (HL Rome):
 *     MSDUs were discarded by the target FW without any over the air
 *     attempts due to lack of space
 */
#define HTT_TX_COMPL_IND_STAT_DISCARD       1
/* NO_ACK:
 * MSDUs were transmitted (repeatedly) but no ACK was received from the peer
 */
#define HTT_TX_COMPL_IND_STAT_NO_ACK        2
/* POSTPONE:
 * temporarily-undeliverable MSDUs were deleted to free up space, but should
 * be downloaded again later (in the appropriate order), when they are
 * deliverable.
 */
#define HTT_TX_COMPL_IND_STAT_POSTPONE      3
/*
 * The PEER_DEL tx completion status is used for HL cases
 * where the peer the frame is for has been deleted.
 * The host has already discarded its copy of the frame, but
 * it still needs the tx completion to restore its credit.
 */
#define HTT_TX_COMPL_IND_STAT_PEER_DEL      4
/* DROP: MSDUs dropped due to lack of space (congestion control) */
#define HTT_TX_COMPL_IND_STAT_DROP          5
#define HTT_TX_COMPL_IND_STAT_HOST_INSPECT  6


#define HTT_TX_COMPL_IND_APPEND_SET_MORE_RETRY(f)  ((f) |= 0x1)
#define HTT_TX_COMPL_IND_APPEND_CLR_MORE_RETRY(f)  ((f) &= (~0x1))

PREPACK struct htt_tx_compl_ind_base {
    A_UINT32 hdr;
    A_UINT16 payload[1/*or more*/];
} POSTPACK;

PREPACK struct htt_tx_compl_ind_append_retries {
    A_UINT16 msdu_id;
    A_UINT8  tx_retries;
    A_UINT8  flag; /* Bit 0, 1: another append_retries struct is appended
                             0: this is the last append_retries struct */
} POSTPACK;

PREPACK struct htt_tx_compl_ind_append_tx_tstamp {
    A_UINT32 timestamp[1/*or more*/];
} POSTPACK;

PREPACK struct htt_tx_compl_ind_append_tx_tsf64 {
    A_UINT32 tx_tsf64_low;
    A_UINT32 tx_tsf64_high;
} POSTPACK;

/* htt_tx_data_hdr_information payload extension fields: */

/* DWORD zero */
#define HTT_FW_TX_DATA_HDR_PHY_TIMESTAMP_L32_M  0xffffffff
#define HTT_FW_TX_DATA_HDR_PHY_TIMESTAMP_L32_S  0

/* DWORD one */
#define HTT_FW_TX_DATA_HDR_PREAMBLE_M           0x00000003
#define HTT_FW_TX_DATA_HDR_PREAMBLE_S           0
#define HTT_FW_TX_DATA_HDR_MCS_M                0x0000003c
#define HTT_FW_TX_DATA_HDR_MCS_S                2
#define HTT_FW_TX_DATA_HDR_RATE_M               0x000001c0
#define HTT_FW_TX_DATA_HDR_RATE_S               6
#define HTT_FW_TX_DATA_HDR_RSSI_M               0x0001fe00
#define HTT_FW_TX_DATA_HDR_RSSI_S               9
#define HTT_FW_TX_DATA_HDR_NSS_M                0x00060000
#define HTT_FW_TX_DATA_HDR_NSS_S                17
#define HTT_FW_TX_DATA_HDR_BW_M                 0x00380000
#define HTT_FW_TX_DATA_HDR_BW_S                 19
#define HTT_FW_TX_DATA_HDR_STBC_M               0x00400000
#define HTT_FW_TX_DATA_HDR_STBC_S               22
#define HTT_FW_TX_DATA_HDR_SGI_M                0x00800000
#define HTT_FW_TX_DATA_HDR_SGI_S                23
#define HTT_FW_TX_DATA_HDR_LDPC_M               0x01000000
#define HTT_FW_TX_DATA_HDR_LDPC_S               24
#define HTT_FW_TX_DATA_HDR_BEAMFORMED_M         0x02000000
#define HTT_FW_TX_DATA_HDR_BEAMFORMED_S         25
#define HTT_FW_TX_DATA_HDR_TX_RETRY_CNT_M       0xfc000000
#define HTT_FW_TX_DATA_HDR_TX_RETRY_CNT_S       26

/* DWORD two */
#define HTT_FW_TX_DATA_HDR_FRAMECTRL_M          0x0000ffff
#define HTT_FW_TX_DATA_HDR_FRAMECTRL_S          0
#define HTT_FW_TX_DATA_HDR_SEQNO_M              0xffff0000
#define HTT_FW_TX_DATA_HDR_SEQNO_S              16


#define HTT_FW_TX_DATA_HDR_PHY_TIMESTAMP_L32_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_PHY_TIMESTAMP_L32, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_PHY_TIMESTAMP_L32_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_PHY_TIMESTAMP_L32_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_PHY_TIMESTAMP_L32_M) >> HTT_FW_TX_DATA_HDR_PHY_TIMESTAMP_L32_S)

#define HTT_FW_TX_DATA_HDR_PREAMBLE_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_PREAMBLE, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_PREAMBLE_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_PREAMBLE_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_PREAMBLE_M) >> HTT_FW_TX_DATA_HDR_PREAMBLE_S)

#define HTT_FW_TX_DATA_HDR_MCS_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_MCS, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_MCS_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_MCS_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_MCS_M) >> HTT_FW_TX_DATA_HDR_MCS_S)

#define HTT_FW_TX_DATA_HDR_RATE_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_RATE, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_RATE_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_RATE_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_RATE_M) >> HTT_FW_TX_DATA_HDR_RATE_S)

#define HTT_FW_TX_DATA_HDR_RSSI_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_RSSI, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_RSSI_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_RSSI_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_RSSI_M) >> HTT_FW_TX_DATA_HDR_RSSI_S)


#define HTT_FW_TX_DATA_HDR_NSS_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_NSS, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_NSS_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_NSS_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_NSS_M) >> HTT_FW_TX_DATA_HDR_NSS_S)

#define HTT_FW_TX_DATA_HDR_BW_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_BW, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_BW_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_BW_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_BW_M) >> HTT_FW_TX_DATA_HDR_BW_S)


#define HTT_FW_TX_DATA_HDR_STBC_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_STBC, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_STBC_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_STBC_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_STBC_M) >> HTT_FW_TX_DATA_HDR_STBC_S)


#define HTT_FW_TX_DATA_HDR_SGI_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_SGI, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_SGI_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_SGI_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_SGI_M) >> HTT_FW_TX_DATA_HDR_SGI_S)

#define HTT_FW_TX_DATA_HDR_LDPC_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_LDPC, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_LDPC_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_LDPC_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_LDPC_M) >> HTT_FW_TX_DATA_HDR_LDPC_S)

#define HTT_FW_TX_DATA_HDR_BEAMFORMED_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_BEAMFORMED, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_BEAMFORMED_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_BEAMFORMED_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_BEAMFORMED_M) >> HTT_FW_TX_DATA_HDR_BEAMFORMED_S)

#define HTT_FW_TX_DATA_HDR_TX_RETRY_CNT_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_TX_RETRY_CNT, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_TX_RETRY_CNT_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_TX_RETRY_CNT_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_TX_RETRY_CNT_M) >> HTT_FW_TX_DATA_HDR_TX_RETRY_CNT_S)

#define HTT_FW_TX_DATA_HDR_FRAMECTRL_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_FRAMECTRL, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_FRAMECTRL_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_FRAMECTRL_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_FRAMECTRL_M) >> HTT_FW_TX_DATA_HDR_FRAMECTRL_S)


#define HTT_FW_TX_DATA_HDR_SEQNO_SET(word, value) \
    do { \
        HTT_CHECK_SET_VAL(HTT_FW_TX_DATA_HDR_SEQNO, value); \
        (word) |= (value)  << HTT_FW_TX_DATA_HDR_SEQNO_S; \
    } while (0)
#define HTT_FW_TX_DATA_HDR_SEQNO_GET(word) \
    (((word) & HTT_FW_TX_DATA_HDR_SEQNO_M) >> HTT_FW_TX_DATA_HDR_SEQNO_S)


/**
 * @brief target -> host rate-control update indication message
 *
 * DEPRECATED (DEPRECATED_HTT_T2H_MSG_TYPE_RC_UPDATE_IND)
 *
 * @details
 * The following diagram shows the format of the RC Update message
 * sent from the target to the host, while processing the tx-completion
 * of a transmitted PPDU.
 *
 *          |31          24|23           16|15            8|7            0|
 *          |-------------------------------------------------------------|
 *          |            peer ID           |    vdev ID    |    msg_type  |
 *          |-------------------------------------------------------------|
 *          |  MAC addr 3  |  MAC addr 2   |   MAC addr 1  |  MAC addr 0  |
 *          |-------------------------------------------------------------|
 *          |   reserved   |   num elems   |   MAC addr 5  |  MAC addr 4  |
 *          |-------------------------------------------------------------|
 *          |                              :                              |
 *          :         HTT_RC_TX_DONE_PARAMS (DWORD-aligned)               :
 *          |                              :                              |
 *          |-------------------------------------------------------------|
 *          |                              :                              |
 *          :         HTT_RC_TX_DONE_PARAMS (DWORD-aligned)               :
 *          |                              :                              |
 *          |-------------------------------------------------------------|
 *          :                                                             :
 *          - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 *
 */

typedef struct {
    A_UINT32 rate_code; /* rate code, bw, chain mask sgi */
    A_UINT32 rate_code_flags;
    A_UINT32 flags;       /* Encodes information such as excessive
                                                  retransmission, aggregate, some info
                                                  from .11 frame control,
                                                  STBC, LDPC, (SGI and Tx Chain Mask
                                                  are encoded in ptx_rc->flags field),
                                                  AMPDU truncation (BT/time based etc.),
                                                  RTS/CTS attempt  */

    A_UINT32 num_enqued;  /* # of MPDUs (for non-AMPDU 1) for this rate */
    A_UINT32 num_retries; /* Total # of transmission attempt for this rate */
    A_UINT32 num_failed;  /* # of failed MPDUs in A-MPDU, 0 otherwise */
    A_UINT32 ack_rssi;    /* ACK RSSI: b'7..b'0 avg RSSI across all chain */
    A_UINT32 time_stamp ; /* ACK timestamp (helps determine age) */
    A_UINT32 is_probe;   /* Valid if probing. Else, 0 */
} HTT_RC_TX_DONE_PARAMS;

#define HTT_RC_UPDATE_CTXT_SZ     (sizeof(HTT_RC_TX_DONE_PARAMS)) /* bytes */
#define HTT_RC_UPDATE_HDR_SZ      (12) /* bytes */

#define HTT_RC_UPDATE_MAC_ADDR_OFFSET   (4) /* bytes */
#define HTT_RC_UPDATE_MAC_ADDR_LENGTH   IEEE80211_ADDR_LEN /* bytes */

#define HTT_RC_UPDATE_VDEVID_S    8
#define HTT_RC_UPDATE_VDEVID_M    0xff00
#define HTT_RC_UPDATE_PEERID_S    16
#define HTT_RC_UPDATE_PEERID_M    0xffff0000

#define HTT_RC_UPDATE_NUM_ELEMS_S   16
#define HTT_RC_UPDATE_NUM_ELEMS_M   0x00ff0000

#define HTT_RC_UPDATE_VDEVID_SET(_info, _val)              \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_RC_UPDATE_VDEVID, _val);     \
        ((_info) |= ((_val) << HTT_RC_UPDATE_VDEVID_S));   \
    } while (0)

#define HTT_RC_UPDATE_VDEVID_GET(_info)                    \
    (((_info) & HTT_RC_UPDATE_VDEVID_M) >> HTT_RC_UPDATE_VDEVID_S)

#define HTT_RC_UPDATE_PEERID_SET(_info, _val)              \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_RC_UPDATE_PEERID, _val);     \
        ((_info) |= ((_val) << HTT_RC_UPDATE_PEERID_S));   \
    } while (0)

#define HTT_RC_UPDATE_PEERID_GET(_info)                    \
    (((_info) & HTT_RC_UPDATE_PEERID_M) >> HTT_RC_UPDATE_PEERID_S)

#define HTT_RC_UPDATE_NUM_ELEMS_SET(_info, _val)            \
    do {                                                    \
        HTT_CHECK_SET_VAL(HTT_RC_UPDATE_NUM_ELEMS, _val);   \
        ((_info) |= ((_val) << HTT_RC_UPDATE_NUM_ELEMS_S)); \
    } while (0)

#define HTT_RC_UPDATE_NUM_ELEMS_GET(_info)                  \
    (((_info) & HTT_RC_UPDATE_NUM_ELEMS_M) >> HTT_RC_UPDATE_NUM_ELEMS_S)

/**
 * @brief target -> host rx fragment indication message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_FRAG_IND
 *
 * @details
 * The following field definitions describe the format of the rx fragment
 * indication message sent from the target to the host.
 * The rx fragment indication message shares the format of the
 * rx indication message, but not all fields from the rx indication message
 * are relevant to the rx fragment indication message.
 *
 *
 *     |31       24|23         18|17|16|15|14|13|12|11|10|9|8|7|6|5|4     0|
 *     |-----------+-------------------+---------------------+-------------|
 *     |             peer ID           |     |FV| ext TID    |  msg type   |
 *     |-------------------------------------------------------------------|
 *     |                                           |    flush    |  flush  |
 *     |                                           |     end     |  start  |
 *     |                                           |   seq num   | seq num |
 *     |-------------------------------------------------------------------|
 *     |           reserved            |         FW rx desc bytes          |
 *     |-------------------------------------------------------------------|
 *     |                                                     | FW MSDU Rx  |
 *     |                                                     |   desc B0   |
 *     |-------------------------------------------------------------------|
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as an rx fragment indication message
 *     Value: 0xa (HTT_T2H_MSG_TYPE_RX_FRAG_IND)
 *   - EXT_TID
 *     Bits 12:8
 *     Purpose: identify the traffic ID of the rx data, including
 *         special "extended" TID values for multicast, broadcast, and
 *         non-QoS data frames
 *     Value: 0-15 for regular TIDs, or >= 16 for bcast/mcast/non-QoS
 *   - FLUSH_VALID (FV)
 *     Bit 13
 *     Purpose: indicate whether the flush IE (start/end sequence numbers)
 *         is valid
 *     Value:
 *         1 -> flush IE is valid and needs to be processed
 *         0 -> flush IE is not valid and should be ignored
 *   - PEER_ID
 *     Bits 31:16
 *     Purpose: Identify, by ID, which peer sent the rx data
 *     Value: ID of the peer who sent the rx data
 *   - FLUSH_SEQ_NUM_START
 *     Bits 5:0
 *     Purpose: Indicate the start of a series of MPDUs to flush
 *         Not all MPDUs within this series are necessarily valid - the host
 *         must check each sequence number within this range to see if the
 *         corresponding MPDU is actually present.
 *         This field is only valid if the FV bit is set.
 *     Value:
 *         The sequence number for the first MPDUs to check to flush.
 *         The sequence number is masked by 0x3f.
 *   - FLUSH_SEQ_NUM_END
 *     Bits 11:6
 *     Purpose: Indicate the end of a series of MPDUs to flush
 *     Value:
 *         The sequence number one larger than the sequence number of the
 *         last MPDU to check to flush.
 *         The sequence number is masked by 0x3f.
 *         Not all MPDUs within this series are necessarily valid - the host
 *         must check each sequence number within this range to see if the
 *         corresponding MPDU is actually present.
 *         This field is only valid if the FV bit is set.
 * Rx descriptor fields:
 *   - FW_RX_DESC_BYTES
 *     Bits 15:0
 *     Purpose: Indicate how many bytes in the Rx indication are used for
 *         FW Rx descriptors
 *     Value: 1
 */
#define HTT_RX_FRAG_IND_HDR_PREFIX_SIZE32         2

#define HTT_RX_FRAG_IND_FW_DESC_BYTE_OFFSET       12

#define HTT_RX_FRAG_IND_EXT_TID_SET     HTT_RX_IND_EXT_TID_SET
#define HTT_RX_FRAG_IND_EXT_TID_GET     HTT_RX_IND_EXT_TID_GET

#define HTT_RX_FRAG_IND_PEER_ID_SET     HTT_RX_IND_PEER_ID_SET
#define HTT_RX_FRAG_IND_PEER_ID_GET     HTT_RX_IND_PEER_ID_GET

#define HTT_RX_FRAG_IND_FLUSH_VALID_SET HTT_RX_IND_FLUSH_VALID_SET
#define HTT_RX_FRAG_IND_FLUSH_VALID_GET HTT_RX_IND_FLUSH_VALID_GET

#define HTT_RX_FRAG_IND_FLUSH_SEQ_NUM_START_SET \
    HTT_RX_IND_FLUSH_SEQ_NUM_START_SET
#define HTT_RX_FRAG_IND_FLUSH_SEQ_NUM_START_GET \
    HTT_RX_IND_FLUSH_SEQ_NUM_START_GET

#define HTT_RX_FRAG_IND_FLUSH_SEQ_NUM_END_SET \
    HTT_RX_IND_FLUSH_SEQ_NUM_END_SET
#define HTT_RX_FRAG_IND_FLUSH_SEQ_NUM_END_GET \
    HTT_RX_IND_FLUSH_SEQ_NUM_END_GET

#define HTT_RX_FRAG_IND_FW_RX_DESC_BYTES_GET  HTT_RX_IND_FW_RX_DESC_BYTES_GET

#define HTT_RX_FRAG_IND_BYTES                 \
    (4 /* msg hdr */ +                        \
     4 /* flush spec */ +                     \
     4 /* (unused) FW rx desc bytes spec */ + \
     4 /* FW rx desc */)

/**
 * @brief target -> host test message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_TEST
 *
 * @details
 * The following field definitions describe the format of the test
 * message sent from the target to the host.
 * The message consists of a 4-octet header, followed by a variable
 * number of 32-bit integer values, followed by a variable number
 * of 8-bit character values.
 *
 * |31                         16|15           8|7            0|
 * |-----------------------------------------------------------|
 * |          num chars          |   num ints   |   msg type   |
 * |-----------------------------------------------------------|
 * |                           int 0                           |
 * |-----------------------------------------------------------|
 * |                           int 1                           |
 * |-----------------------------------------------------------|
 * |                            ...                            |
 * |-----------------------------------------------------------|
 * |    char 3    |    char 2    |    char 1    |    char 0    |
 * |-----------------------------------------------------------|
 * |              |              |      ...     |    char 4    |
 * |-----------------------------------------------------------|
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a test message
 *     Value: HTT_MSG_TYPE_TEST
 *   - NUM_INTS
 *     Bits 15:8
 *     Purpose: indicate how many 32-bit integers follow the message header
 *   - NUM_CHARS
 *     Bits 31:16
 *     Purpose: indicate how many 8-bit charaters follow the series of integers
 */
#define HTT_RX_TEST_NUM_INTS_M   0xff00
#define HTT_RX_TEST_NUM_INTS_S   8
#define HTT_RX_TEST_NUM_CHARS_M  0xffff0000
#define HTT_RX_TEST_NUM_CHARS_S  16

#define HTT_RX_TEST_NUM_INTS_SET(word, value)                           \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_TEST_NUM_INTS, value);                 \
        (word) |= (value)  << HTT_RX_TEST_NUM_INTS_S;                   \
    } while (0)
#define HTT_RX_TEST_NUM_INTS_GET(word) \
    (((word) & HTT_RX_TEST_NUM_INTS_M) >> HTT_RX_TEST_NUM_INTS_S)

#define HTT_RX_TEST_NUM_CHARS_SET(word, value)                          \
    do {                                                                \
        HTT_CHECK_SET_VAL(HTT_RX_TEST_NUM_CHARS, value);                \
        (word) |= (value)  << HTT_RX_TEST_NUM_CHARS_S;                  \
    } while (0)
#define HTT_RX_TEST_NUM_CHARS_GET(word) \
    (((word) & HTT_RX_TEST_NUM_CHARS_M) >> HTT_RX_TEST_NUM_CHARS_S)

/**
 * @brief target -> host packet log message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_PKTLOG
 *
 * @details
 * The following field definitions describe the format of the packet log
 * message sent from the target to the host.
 * The message consists of a 4-octet header,followed by a variable number
 * of 32-bit character values.
 *
 * |31                         16|15  12|11   10|9    8|7            0|
 * |------------------------------------------------------------------|
 * |        payload_size         | rsvd |pdev_id|mac_id|   msg type   |
 * |------------------------------------------------------------------|
 * |                              payload                             |
 * |------------------------------------------------------------------|
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a pktlog message
 *     Value: 0x8 (HTT_T2H_MSG_TYPE_PKTLOG)
 *   - mac_id
 *     Bits 9:8
 *     Purpose: identifies which MAC/PHY instance generated this pktlog info
 *     Value: 0-3
 *   - pdev_id
 *     Bits 11:10
 *     Purpose: pdev_id
 *     Value: 0-3
 *     0 (for rings at SOC level),
 *     1/2/3 PDEV -> 0/1/2
 *   - payload_size
 *     Bits 31:16
 *     Purpose: explicitly specify the payload size
 *     Value: payload size in bytes (payload size is a multiple of 4 bytes)
 */
PREPACK struct htt_pktlog_msg {
    A_UINT32 header;
    A_UINT32 payload[1/* or more */];
} POSTPACK;

#define HTT_T2H_PKTLOG_MAC_ID_M           0x00000300
#define HTT_T2H_PKTLOG_MAC_ID_S           8

#define HTT_T2H_PKTLOG_PDEV_ID_M          0x00000C00
#define HTT_T2H_PKTLOG_PDEV_ID_S          10

#define HTT_T2H_PKTLOG_PAYLOAD_SIZE_M     0xFFFF0000
#define HTT_T2H_PKTLOG_PAYLOAD_SIZE_S     16

#define HTT_T2H_PKTLOG_MAC_ID_SET(word, value)             \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_PKTLOG_MAC_ID, value);   \
        (word) |= (value)  << HTT_T2H_PKTLOG_MAC_ID_S;     \
    } while (0)
#define HTT_T2H_PKTLOG_MAC_ID_GET(word) \
    (((word) & HTT_T2H_PKTLOG_MAC_ID_M) >> \
    HTT_T2H_PKTLOG_MAC_ID_S)

#define HTT_T2H_PKTLOG_PDEV_ID_SET(word, value)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_PKTLOG_PDEV_ID, value);  \
        (word) |= (value)  << HTT_T2H_PKTLOG_PDEV_ID_S;    \
    } while (0)
#define HTT_T2H_PKTLOG_PDEV_ID_GET(word) \
    (((word) & HTT_T2H_PKTLOG_PDEV_ID_M) >> \
    HTT_T2H_PKTLOG_PDEV_ID_S)

#define HTT_T2H_PKTLOG_PAYLOAD_SIZE_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_PKTLOG_PAYLOAD_SIZE, value);   \
        (word) |= (value)  << HTT_T2H_PKTLOG_PAYLOAD_SIZE_S;     \
    } while (0)
#define HTT_T2H_PKTLOG_PAYLOAD_SIZE_GET(word) \
    (((word) & HTT_T2H_PKTLOG_PAYLOAD_SIZE_M) >> \
    HTT_T2H_PKTLOG_PAYLOAD_SIZE_S)

/*
 * Rx reorder statistics
 * NB: all the fields must be defined in 4 octets size.
 */
struct rx_reorder_stats {
    /* Non QoS MPDUs received */
    A_UINT32 deliver_non_qos;
    /* MPDUs received in-order */
    A_UINT32 deliver_in_order;
    /* Flush due to reorder timer expired */
    A_UINT32 deliver_flush_timeout;
    /* Flush due to move out of window */
    A_UINT32 deliver_flush_oow;
    /* Flush due to DELBA */
    A_UINT32 deliver_flush_delba;
    /* MPDUs dropped due to FCS error */
    A_UINT32 fcs_error;
    /* MPDUs dropped due to monitor mode non-data packet */
    A_UINT32 mgmt_ctrl;
    /* Unicast-data MPDUs dropped due to invalid peer */
    A_UINT32 invalid_peer;
    /* MPDUs dropped due to duplication (non aggregation) */
    A_UINT32 dup_non_aggr;
    /* MPDUs dropped due to processed before */
    A_UINT32 dup_past;
    /* MPDUs dropped due to duplicate in reorder queue */
    A_UINT32 dup_in_reorder;
    /* Reorder timeout happened */
    A_UINT32 reorder_timeout;
    /* invalid bar ssn */
    A_UINT32 invalid_bar_ssn;
    /* reorder reset due to bar ssn */
    A_UINT32 ssn_reset;
    /* Flush due to delete peer */
    A_UINT32 deliver_flush_delpeer;
    /* Flush due to offload*/
    A_UINT32 deliver_flush_offload;
    /* Flush due to out of buffer*/
    A_UINT32 deliver_flush_oob;
    /* MPDUs dropped due to PN check fail */
    A_UINT32 pn_fail;
    /* MPDUs dropped due to unable to allocate memory  */
    A_UINT32 store_fail;
    /* Number of times the tid pool alloc succeeded */
    A_UINT32 tid_pool_alloc_succ;
    /* Number of times the MPDU pool alloc succeeded */
    A_UINT32 mpdu_pool_alloc_succ;
    /* Number of times the MSDU pool alloc succeeded */
    A_UINT32 msdu_pool_alloc_succ;
    /* Number of times the tid pool alloc failed */
    A_UINT32 tid_pool_alloc_fail;
    /* Number of times the MPDU pool alloc failed */
    A_UINT32 mpdu_pool_alloc_fail;
    /* Number of times the MSDU pool alloc failed */
    A_UINT32 msdu_pool_alloc_fail;
    /* Number of times the tid pool freed */
    A_UINT32 tid_pool_free;
    /* Number of times the MPDU pool freed */
    A_UINT32 mpdu_pool_free;
    /* Number of times the MSDU pool freed */
    A_UINT32 msdu_pool_free;
    /* number of MSDUs undelivered to HTT and queued to Data Rx MSDU free list*/
    A_UINT32 msdu_queued;
    /* Number of MSDUs released from Data Rx MSDU list to MAC ring */
    A_UINT32 msdu_recycled;
    /* Number of MPDUs with invalid peer but A2 found in AST */
    A_UINT32 invalid_peer_a2_in_ast;
    /* Number of MPDUs with invalid peer but A3 found in AST */
    A_UINT32 invalid_peer_a3_in_ast;
    /* Number of MPDUs with invalid peer, Broadcast or Multicast frame */
    A_UINT32 invalid_peer_bmc_mpdus;
    /* Number of MSDUs with err attention word */
    A_UINT32 rxdesc_err_att;
    /* Number of MSDUs with flag of peer_idx_invalid */
    A_UINT32 rxdesc_err_peer_idx_inv;
    /* Number of MSDUs with flag of peer_idx_timeout */
    A_UINT32 rxdesc_err_peer_idx_to;
    /* Number of MSDUs with flag of overflow */
    A_UINT32 rxdesc_err_ov;
    /* Number of MSDUs with flag of msdu_length_err */
    A_UINT32 rxdesc_err_msdu_len;
    /* Number of MSDUs with flag of mpdu_length_err */
    A_UINT32 rxdesc_err_mpdu_len;
    /* Number of MSDUs with flag of tkip_mic_err */
    A_UINT32 rxdesc_err_tkip_mic;
    /* Number of MSDUs with flag of decrypt_err */
    A_UINT32 rxdesc_err_decrypt;
    /* Number of MSDUs with flag of fcs_err */
    A_UINT32 rxdesc_err_fcs;
    /* Number of Unicast (bc_mc bit is not set in attention word)
     * frames with invalid peer handler
     */
    A_UINT32 rxdesc_uc_msdus_inv_peer;
    /* Number of unicast frame directly (direct bit is set in attention word)
     * to DUT with invalid peer handler
     */
    A_UINT32 rxdesc_direct_msdus_inv_peer;
    /* Number of Broadcast/Multicast (bc_mc bit set in attention word)
     * frames with invalid peer handler
     */
    A_UINT32 rxdesc_bmc_msdus_inv_peer;
    /* Number of MSDUs dropped due to no first MSDU flag */
    A_UINT32 rxdesc_no_1st_msdu;
    /* Number of MSDUs droped due to ring overflow */
    A_UINT32 msdu_drop_ring_ov;
    /* Number of MSDUs dropped due to FC mismatch */
    A_UINT32 msdu_drop_fc_mismatch;
    /* Number of MSDUs dropped due to mgt frame in Remote ring */
    A_UINT32 msdu_drop_mgmt_remote_ring;
    /* Number of MSDUs dropped due to errors not reported in attention word */
    A_UINT32 msdu_drop_misc;
    /* Number of MSDUs go to offload before reorder */
    A_UINT32 offload_msdu_wal;
    /* Number of data frame dropped by offload after reorder */
    A_UINT32 offload_msdu_reorder;
    /* Number of MPDUs with sequence number in the past and within the BA window */
    A_UINT32 dup_past_within_window;
    /* Number of MPDUs with sequence number in the past and outside the BA window */
    A_UINT32 dup_past_outside_window;
    /* Number of MSDUs with decrypt/MIC error */
    A_UINT32 rxdesc_err_decrypt_mic;
    /* Number of data MSDUs received on both local and remote rings */
    A_UINT32 data_msdus_on_both_rings;
    /* MPDUs never filled */
    A_UINT32 holes_not_filled;
};


/*
 * Rx Remote buffer statistics
 * NB: all the fields must be defined in 4 octets size.
 */
struct rx_remote_buffer_mgmt_stats {
    /* Total number of MSDUs reaped for Rx processing */
    A_UINT32 remote_reaped;
    /* MSDUs recycled within firmware */
    A_UINT32 remote_recycled;
    /* MSDUs stored by Data Rx */
    A_UINT32 data_rx_msdus_stored;
    /* Number of HTT indications from WAL Rx MSDU */
    A_UINT32 wal_rx_ind;
    /* Number of unconsumed HTT indications from WAL Rx MSDU */
    A_UINT32 wal_rx_ind_unconsumed;
    /* Number of HTT indications from Data Rx MSDU */
    A_UINT32 data_rx_ind;
    /* Number of unconsumed HTT indications from Data Rx MSDU */
    A_UINT32 data_rx_ind_unconsumed;
    /* Number of HTT indications from ATHBUF */
    A_UINT32 athbuf_rx_ind;
    /* Number of remote buffers requested for refill */
    A_UINT32 refill_buf_req;
    /* Number of remote buffers filled by the host */
    A_UINT32 refill_buf_rsp;
    /* Number of times MAC hw_index = f/w write_index */
    A_INT32 mac_no_bufs;
    /* Number of times f/w write_index = f/w read_index for MAC Rx ring */
    A_INT32 fw_indices_equal;
    /* Number of times f/w finds no buffers to post */
    A_INT32 host_no_bufs;
};

/*
 * TXBF MU/SU packets and NDPA statistics
 * NB: all the fields must be defined in 4 octets size.
 */
struct rx_txbf_musu_ndpa_pkts_stats {
    A_UINT32 number_mu_pkts;           /* number of TXBF MU packets received */
    A_UINT32 number_su_pkts;           /* number of TXBF SU packets received */
    A_UINT32 txbf_directed_ndpa_count; /* number of TXBF directed NDPA */
    A_UINT32 txbf_ndpa_retry_count;    /* number of TXBF retried NDPA */
    A_UINT32 txbf_total_ndpa_count;    /* total number of TXBF NDPA */

    A_UINT32 reserved[3]; /* must be set to 0x0 */
};


/*
 * htt_dbg_stats_status -
 * present -     The requested stats have been delivered in full.
 *               This indicates that either the stats information was contained
 *               in its entirety within this message, or else this message
 *               completes the delivery of the requested stats info that was
 *               partially delivered through earlier STATS_CONF messages.
 * partial -     The requested stats have been delivered in part.
 *               One or more subsequent STATS_CONF messages with the same
 *               cookie value will be sent to deliver the remainder of the
 *               information.
 * error -       The requested stats could not be delivered, for example due
 *               to a shortage of memory to construct a message holding the
 *               requested stats.
 * invalid -     The requested stat type is either not recognized, or the
 *               target is configured to not gather the stats type in question.
 * - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 * series_done - This special value indicates that no further stats info
 *               elements are present within a series of stats info elems
 *               (within a stats upload confirmation message).
 */
enum htt_dbg_stats_status {
    HTT_DBG_STATS_STATUS_PRESENT = 0,
    HTT_DBG_STATS_STATUS_PARTIAL = 1,
    HTT_DBG_STATS_STATUS_ERROR   = 2,
    HTT_DBG_STATS_STATUS_INVALID = 3,


    HTT_DBG_STATS_STATUS_SERIES_DONE = 7
};

/**
 * @brief target -> host statistics upload
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_STATS_CONF
 *
 * @details
 * The following field definitions describe the format of the HTT target
 * to host stats upload confirmation message.
 * The message contains a cookie echoed from the HTT host->target stats
 * upload request, which identifies which request the confirmation is
 * for, and a series of tag-length-value stats information elements.
 * The tag-length header for each stats info element also includes a
 * status field, to indicate whether the request for the stat type in
 * question was fully met, partially met, unable to be met, or invalid
 * (if the stat type in question is disabled in the target).
 * A special value of all 1's in this status field is used to indicate
 * the end of the series of stats info elements.
 *
 *
 * |31                         16|15           8|7   5|4       0|
 * |------------------------------------------------------------|
 * |                  reserved                  |    msg type   |
 * |------------------------------------------------------------|
 * |                        cookie LSBs                         |
 * |------------------------------------------------------------|
 * |                        cookie MSBs                         |
 * |------------------------------------------------------------|
 * |      stats entry length     |   reserved   |  S  |stat type|
 * |------------------------------------------------------------|
 * |                                                            |
 * |                  type-specific stats info                  |
 * |                                                            |
 * |------------------------------------------------------------|
 * |      stats entry length     |   reserved   |  S  |stat type|
 * |------------------------------------------------------------|
 * |                                                            |
 * |                  type-specific stats info                  |
 * |                                                            |
 * |------------------------------------------------------------|
 * |              n/a            |   reserved   | 111 |   n/a   |
 * |------------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Purpose: identifies this is a statistics upload confirmation message
 *    Value: 0x9 (HTT_T2H_MSG_TYPE_STATS_CONF)
 *  - COOKIE_LSBS
 *    Bits 31:0
 *    Purpose: Provide a mechanism to match a target->host stats confirmation
 *        message with its preceding host->target stats request message.
 *    Value: LSBs of the opaque cookie specified by the host-side requestor
 *  - COOKIE_MSBS
 *    Bits 31:0
 *    Purpose: Provide a mechanism to match a target->host stats confirmation
 *        message with its preceding host->target stats request message.
 *    Value: MSBs of the opaque cookie specified by the host-side requestor
 *
 * Stats Information Element tag-length header fields:
 *  - STAT_TYPE
 *    Bits 4:0
 *    Purpose: identifies the type of statistics info held in the
 *        following information element
 *    Value: htt_dbg_stats_type
 *  - STATUS
 *    Bits 7:5
 *    Purpose: indicate whether the requested stats are present
 *    Value: htt_dbg_stats_status, including a special value (0x7) to mark
 *        the completion of the stats entry series
 *  - LENGTH
 *    Bits 31:16
 *    Purpose: indicate the stats information size
 *    Value: This field specifies the number of bytes of stats information
 *       that follows the element tag-length header.
 *       It is expected but not required that this length is a multiple of
 *       4 bytes.  Even if the length is not an integer multiple of 4, the
 *       subsequent stats entry header will begin on a 4-byte aligned
 *       boundary.
 */
#define HTT_T2H_STATS_COOKIE_SIZE         8

#define HTT_T2H_STATS_CONF_TAIL_SIZE      4

#define HTT_T2H_STATS_CONF_HDR_SIZE       4

#define HTT_T2H_STATS_CONF_TLV_HDR_SIZE   4

#define HTT_T2H_STATS_CONF_TLV_TYPE_M     0x0000001f
#define HTT_T2H_STATS_CONF_TLV_TYPE_S     0
#define HTT_T2H_STATS_CONF_TLV_STATUS_M   0x000000e0
#define HTT_T2H_STATS_CONF_TLV_STATUS_S   5
#define HTT_T2H_STATS_CONF_TLV_LENGTH_M   0xffff0000
#define HTT_T2H_STATS_CONF_TLV_LENGTH_S   16

#define HTT_T2H_STATS_CONF_TLV_TYPE_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_STATS_CONF_TLV_TYPE, value);   \
        (word) |= (value)  << HTT_T2H_STATS_CONF_TLV_TYPE_S;     \
    } while (0)
#define HTT_T2H_STATS_CONF_TLV_TYPE_GET(word) \
    (((word) & HTT_T2H_STATS_CONF_TLV_TYPE_M) >> \
    HTT_T2H_STATS_CONF_TLV_TYPE_S)

#define HTT_T2H_STATS_CONF_TLV_STATUS_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_STATS_CONF_TLV_STATUS, value);   \
        (word) |= (value)  << HTT_T2H_STATS_CONF_TLV_STATUS_S;     \
    } while (0)
#define HTT_T2H_STATS_CONF_TLV_STATUS_GET(word) \
    (((word) & HTT_T2H_STATS_CONF_TLV_STATUS_M) >> \
    HTT_T2H_STATS_CONF_TLV_STATUS_S)

#define HTT_T2H_STATS_CONF_TLV_LENGTH_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_STATS_CONF_TLV_LENGTH, value);   \
        (word) |= (value)  << HTT_T2H_STATS_CONF_TLV_LENGTH_S;     \
    } while (0)
#define HTT_T2H_STATS_CONF_TLV_LENGTH_GET(word) \
    (((word) & HTT_T2H_STATS_CONF_TLV_LENGTH_M) >> \
    HTT_T2H_STATS_CONF_TLV_LENGTH_S)

#define HL_HTT_FW_RX_DESC_RSVD_SIZE 18
#define HTT_MAX_AGGR 64
#define HTT_HL_MAX_AGGR 18

/**
 * @brief host -> target FRAG DESCRIPTOR/MSDU_EXT DESC bank
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG
 *
 * @details
 * The following field definitions describe the format of the HTT host
 * to target frag_desc/msdu_ext bank configuration message.
 * The message contains the based address and the min and max id of the
 * MSDU_EXT/FRAG_DESC that will be used by the HTT to map MSDU DESC and
 * MSDU_EXT/FRAG_DESC.
 * HTT will use id in HTT descriptor instead sending the frag_desc_ptr.
 * In peregrine the firmware will use fragment_desc_ptr but in WIFI2.0
 * the hardware does the mapping/translation.
 *
 * Total banks that can be configured is configured to 16.
 *
 * This should be called before any TX has be initiated by the HTT
 *
 * |31                         16|15           8|7   5|4       0|
 * |------------------------------------------------------------|
 * | DESC_SIZE    |  NUM_BANKS   | RES |SWP|pdev|    msg type   |
 * |------------------------------------------------------------|
 * |                 BANK0_BASE_ADDRESS (bits 31:0)             |
#if HTT_PADDR64
 * |                 BANK0_BASE_ADDRESS (bits 63:32)            |
#endif
 * |------------------------------------------------------------|
 * |                            ...                             |
 * |------------------------------------------------------------|
 * |                 BANK15_BASE_ADDRESS (bits 31:0)            |
#if HTT_PADDR64
 * |                 BANK15_BASE_ADDRESS (bits 63:32)           |
#endif
 * |------------------------------------------------------------|
 * |       BANK0_MAX_ID          |       BANK0_MIN_ID           |
 * |------------------------------------------------------------|
 * |                            ...                             |
 * |------------------------------------------------------------|
 * |       BANK15_MAX_ID         |       BANK15_MIN_ID          |
 * |------------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Value: 0x6 (HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG)
 *  for systems with 64-bit format for bus addresses:
 *      - BANKx_BASE_ADDRESS_LO
 *        Bits 31:0
 *        Purpose: Provide a mechanism to specify the base address of the
 *             MSDU_EXT bank physical/bus address.
 *        Value: lower 4 bytes of MSDU_EXT bank physical / bus address
 *      - BANKx_BASE_ADDRESS_HI
 *        Bits 31:0
 *        Purpose: Provide a mechanism to specify the base address of the
 *             MSDU_EXT bank physical/bus address.
 *        Value: higher 4 bytes of MSDU_EXT bank physical / bus address
 *  for systems with 32-bit format for bus addresses:
 *      - BANKx_BASE_ADDRESS
 *        Bits 31:0
 *        Purpose: Provide a mechanism to specify the base address of the
 *             MSDU_EXT bank physical/bus address.
 *        Value: MSDU_EXT bank physical / bus address
 *  - BANKx_MIN_ID
 *    Bits 15:0
 *    Purpose: Provide a mechanism to specify the min index that needs to
 *          mapped.
 *  - BANKx_MAX_ID
 *    Bits 31:16
 *    Purpose: Provide a mechanism to specify the max index that needs to
 *          mapped.
 *
 */

/** @todo Compress the fields to fit MAX HTT Message size, until then configure to a
 *         safe value.
 *  @note MAX supported banks is 16.
 */
#define HTT_TX_MSDU_EXT_BANK_MAX 4

#define HTT_H2T_FRAG_DESC_BANK_PDEVID_M       0x300
#define HTT_H2T_FRAG_DESC_BANK_PDEVID_S       8

#define HTT_H2T_FRAG_DESC_BANK_SWAP_M         0x400
#define HTT_H2T_FRAG_DESC_BANK_SWAP_S         10

#define HTT_H2T_FRAG_DESC_BANK_NUM_BANKS_M    0xff0000
#define HTT_H2T_FRAG_DESC_BANK_NUM_BANKS_S    16

#define HTT_H2T_FRAG_DESC_BANK_DESC_SIZE_M    0xff000000
#define HTT_H2T_FRAG_DESC_BANK_DESC_SIZE_S    24

#define HTT_H2T_FRAG_DESC_BANK_MIN_IDX_M      0xffff
#define HTT_H2T_FRAG_DESC_BANK_MIN_IDX_S      0

#define HTT_H2T_FRAG_DESC_BANK_MAX_IDX_M      0xffff0000
#define HTT_H2T_FRAG_DESC_BANK_MAX_IDX_S      16

#define HTT_H2T_FRAG_DESC_BANK_PDEVID_SET(word, value)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_H2T_FRAG_DESC_BANK_PDEVID, value); \
        (word) |= ((value) << HTT_H2T_FRAG_DESC_BANK_PDEVID_S);  \
    } while (0)
#define HTT_H2T_FRAG_DESC_BANK_PDEVID_GET(word) \
    (((word) & HTT_H2T_FRAG_DESC_BANK_PDEVID_M) >> HTT_H2T_FRAG_DESC_BANK_PDEVID_S)

#define HTT_H2T_FRAG_DESC_BANK_SWAP_SET(word, value)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_H2T_FRAG_DESC_BANK_SWAP, value); \
        (word) |= ((value) << HTT_H2T_FRAG_DESC_BANK_SWAP_S);  \
    } while (0)
#define HTT_H2T_FRAG_DESC_BANK_SWAP_GET(word) \
    (((word) & HTT_H2T_FRAG_DESC_BANK_SWAP_M) >> HTT_H2T_FRAG_DESC_BANK_SWAP_S)

#define HTT_H2T_FRAG_DESC_BANK_NUM_BANKS_SET(word, value)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_H2T_FRAG_DESC_BANK_NUM_BANKS, value); \
        (word) |= ((value) << HTT_H2T_FRAG_DESC_BANK_NUM_BANKS_S);  \
    } while (0)
#define HTT_H2T_FRAG_DESC_BANK_NUM_BANKS_GET(word) \
    (((word) & HTT_H2T_FRAG_DESC_BANK_NUM_BANKS_M) >> HTT_H2T_FRAG_DESC_BANK_NUM_BANKS_S)

#define HTT_H2T_FRAG_DESC_BANK_DESC_SIZE_SET(word, value)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_H2T_FRAG_DESC_BANK_DESC_SIZE, value); \
        (word) |= ((value) << HTT_H2T_FRAG_DESC_BANK_DESC_SIZE_S);  \
    } while (0)
#define HTT_H2T_FRAG_DESC_BANK_DESC_SIZE_GET(word) \
    (((word) & HTT_H2T_FRAG_DESC_BANK_DESC_SIZE_M) >> HTT_H2T_FRAG_DESC_BANK_DESC_SIZE_S)

#define HTT_H2T_FRAG_DESC_BANK_MIN_IDX_SET(word, value)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_H2T_FRAG_DESC_BANK_MIN_IDX, value); \
        (word) |= ((value) << HTT_H2T_FRAG_DESC_BANK_MIN_IDX_S);  \
    } while (0)
#define HTT_H2T_FRAG_DESC_BANK_MIN_IDX_GET(word) \
    (((word) & HTT_H2T_FRAG_DESC_BANK_MIN_IDX_M) >> HTT_H2T_FRAG_DESC_BANK_MIN_IDX_S)

#define HTT_H2T_FRAG_DESC_BANK_MAX_IDX_SET(word, value)           \
    do {                                               \
        HTT_CHECK_SET_VAL(HTT_H2T_FRAG_DESC_BANK_MAX_IDX, value); \
        (word) |= ((value) << HTT_H2T_FRAG_DESC_BANK_MAX_IDX_S);  \
    } while (0)
#define HTT_H2T_FRAG_DESC_BANK_MAX_IDX_GET(word) \
    (((word) & HTT_H2T_FRAG_DESC_BANK_MAX_IDX_M) >> HTT_H2T_FRAG_DESC_BANK_MAX_IDX_S)


/*
 * TEMPLATE_HTT_TX_FRAG_DESC_BANK_CFG_T:
 * This macro defines a htt_tx_frag_descXXX_bank_cfg_t in which any physical
 * addresses are stored in a XXX-bit field.
 * This macro is used to define both htt_tx_frag_desc32_bank_cfg_t and
 * htt_tx_frag_desc64_bank_cfg_t structs.
 */
#define TEMPLATE_HTT_TX_FRAG_DESC_BANK_CFG_T(                                  \
    _paddr_bits_,                                                              \
    _paddr__bank_base_address_)                                                \
PREPACK struct htt_tx_frag_desc ## _paddr_bits_ ## _bank_cfg_t {               \
      /** word 0                                                               \
       * msg_type:     8,                                                      \
       * pdev_id:      2,                                                      \
       * swap:         1,                                                      \
       * reserved0:    5,                                                      \
       * num_banks:    8,                                                      \
       * desc_size:    8;                                                      \
       */                                                                      \
    A_UINT32 word0;                                                            \
    /*                                                                         \
     * If bank_base_address is 64 bits, the upper / lower halves are stored    \
     * in little-endian order (bytes 0-3 in the first A_UINT32, bytes 4-7 in   \
     * the second A_UINT32).                                                   \
     */                                                                        \
    _paddr__bank_base_address_[HTT_TX_MSDU_EXT_BANK_MAX];                      \
    A_UINT32 bank_info[HTT_TX_MSDU_EXT_BANK_MAX];                              \
} POSTPACK
/* define htt_tx_frag_desc32_bank_cfg_t */
TEMPLATE_HTT_TX_FRAG_DESC_BANK_CFG_T(32, HTT_VAR_PADDR32(bank_base_address));
/* define htt_tx_frag_desc64_bank_cfg_t */
TEMPLATE_HTT_TX_FRAG_DESC_BANK_CFG_T(64, HTT_VAR_PADDR64_LE(bank_base_address));
/*
 * Make htt_tx_frag_desc_bank_cfg_t be an alias for either
 * htt_tx_frag_desc32_bank_cfg_t or htt_tx_frag_desc64_bank_cfg_t
 */
#if HTT_PADDR64
    #define htt_tx_frag_desc_bank_cfg_t htt_tx_frag_desc64_bank_cfg_t
#else
    #define htt_tx_frag_desc_bank_cfg_t htt_tx_frag_desc32_bank_cfg_t
#endif

/**
 * @brief target -> host HTT TX Credit total count update message definition
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_TX_CREDIT_UPDATE_IND
 *
 *|31                 16|15|14       9|  8    |7       0 |
 *|---------------------+--+----------+-------+----------|
 *|cur htt credit delta | Q| reserved | sign  | msg type |
 *|------------------------------------------------------|
 *
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a htt tx credit delta update message
 *     Value: 0xf (HTT_T2H_MSG_TYPE_TX_CREDIT_UPDATE_IND)
 *   - SIGN
 *     Bits 8
 *      identifies whether credit delta is positive or negative
 *     Value:
 *       - 0x0: credit delta is positive, rebalance in some buffers
 *       - 0x1: credit delta is negative, rebalance out some buffers
 *   - reserved
 *     Bits 14:9
 *     Value: 0x0
 *   - TXQ_GRP
 *     Bit 15
 *     Purpose: indicates whether any tx queue group information elements
 *         are appended to the tx credit update message
 *     Value: 0 -> no tx queue group information element is present
 *            1 -> a tx queue group information element immediately follows
 *   - DELTA_COUNT
 *     Bits 31:16
 *     Purpose: Specify current htt credit delta absolute count
 */

#define HTT_TX_CREDIT_SIGN_BIT_M       0x00000100
#define HTT_TX_CREDIT_SIGN_BIT_S       8
#define HTT_TX_CREDIT_TXQ_GRP_M        0x00008000
#define HTT_TX_CREDIT_TXQ_GRP_S        15
#define HTT_TX_CREDIT_DELTA_ABS_M      0xffff0000
#define HTT_TX_CREDIT_DELTA_ABS_S      16


#define HTT_TX_CREDIT_SIGN_BIT_SET(word, value)                              \
    do {                                                                     \
        HTT_CHECK_SET_VAL(HTT_TX_CREDIT_SIGN_BIT, value);                    \
        (word) |= (value)  << HTT_TX_CREDIT_SIGN_BIT_S;                      \
    } while (0)

#define HTT_TX_CREDIT_SIGN_BIT_GET(word) \
    (((word) & HTT_TX_CREDIT_SIGN_BIT_M) >> HTT_TX_CREDIT_SIGN_BIT_S)

#define HTT_TX_CREDIT_TXQ_GRP_SET(word, value)                              \
    do {                                                                    \
        HTT_CHECK_SET_VAL(HTT_TX_CREDIT_TXQ_GRP, value);                    \
        (word) |= (value)  << HTT_TX_CREDIT_TXQ_GRP_S;                      \
    } while (0)

#define HTT_TX_CREDIT_TXQ_GRP_GET(word) \
    (((word) & HTT_TX_CREDIT_TXQ_GRP_M) >> HTT_TX_CREDIT_TXQ_GRP_S)

#define HTT_TX_CREDIT_DELTA_ABS_SET(word, value)                              \
    do {                                                                      \
        HTT_CHECK_SET_VAL(HTT_TX_CREDIT_DELTA_ABS, value);                    \
        (word) |= (value)  << HTT_TX_CREDIT_DELTA_ABS_S;                      \
    } while (0)

#define HTT_TX_CREDIT_DELTA_ABS_GET(word) \
    (((word) & HTT_TX_CREDIT_DELTA_ABS_M) >> HTT_TX_CREDIT_DELTA_ABS_S)


#define HTT_TX_CREDIT_MSG_BYTES 4

#define HTT_TX_CREDIT_SIGN_BIT_POSITIVE  0x0
#define HTT_TX_CREDIT_SIGN_BIT_NEGATIVE  0x1


/**
 * @brief HTT WDI_IPA Operation Response Message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_WDI_IPA_OP_RESPONSE
 *
 * @details
 *  HTT WDI_IPA Operation Response message is sent by target
 *  to host confirming suspend or resume operation.
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |             op_code             |      Rsvd      |     msg_type   |
 *     |-------------------------------------------------------------------|
 *     |             Rsvd                |          Response len           |
 *     |-------------------------------------------------------------------|
 *     |                                                                   |
 *     |                  Response-type specific info                      |
 *     |                                                                   |
 *     |                                                                   |
 *     |-------------------------------------------------------------------|
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: Identifies this as WDI_IPA Operation Response message
 *     value: = 0x14 (HTT_T2H_MSG_TYPE_WDI_IPA_OP_RESPONSE)
 *   - OP_CODE
 *     Bits 31:16
 *     Purpose: Identifies the operation target is responding to (e.g. TX suspend)
 *     value: = enum htt_wdi_ipa_op_code
 *   - RSP_LEN
 *     Bits 16:0
 *     Purpose: length for the response-type specific info
 *     value: = length in bytes for response-type specific info
 *              For example, if OP_CODE == HTT_WDI_IPA_OPCODE_DBG_STATS, the
 *              length value will be sizeof(struct wlan_wdi_ipa_dbg_stats_t).
 */

PREPACK struct htt_wdi_ipa_op_response_t
{
    /* DWORD 0: flags and meta-data */
    A_UINT32
        msg_type:   8, /* HTT_T2H_MSG_TYPE_WDI_IPA_OP_RESPONSE */
        reserved1:  8,
        op_code:   16;
    A_UINT32
        rsp_len:   16,
        reserved2: 16;
} POSTPACK;

#define HTT_WDI_IPA_OP_RESPONSE_SZ                    8 /* bytes */

#define HTT_WDI_IPA_OP_RESPONSE_OP_CODE_M             0xffff0000
#define HTT_WDI_IPA_OP_RESPONSE_OP_CODE_S             16

#define HTT_WDI_IPA_OP_RESPONSE_RSP_LEN_M             0x0000ffff
#define HTT_WDI_IPA_OP_RESPONSE_RSP_LEN_S             0

#define HTT_WDI_IPA_OP_RESPONSE_OP_CODE_GET(_var) \
    (((_var) & HTT_WDI_IPA_OP_RESPONSE_OP_CODE_M) >> HTT_WDI_IPA_OP_RESPONSE_OP_CODE_S)
#define HTT_WDI_IPA_OP_RESPONSE_OP_CODE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_OP_RESPONSE_OP_CODE, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_OP_RESPONSE_OP_CODE_S)); \
    } while (0)

#define HTT_WDI_IPA_OP_RESPONSE_RSP_LEN_GET(_var) \
    (((_var) & HTT_WDI_IPA_OP_RESPONSE_RSP_LEN_M) >> HTT_WDI_IPA_OP_RESPONSE_RSP_LEN_S)
#define HTT_WDI_IPA_OP_RESPONSE_RSP_LEN_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_WDI_IPA_OP_RESPONSE_RSP_LEN, _val);  \
        ((_var) |= ((_val) << HTT_WDI_IPA_OP_RESPONSE_RSP_LEN_S)); \
    } while (0)


enum htt_phy_mode {
    htt_phy_mode_11a            = 0,
    htt_phy_mode_11g            = 1,
    htt_phy_mode_11b            = 2,
    htt_phy_mode_11g_only       = 3,
    htt_phy_mode_11na_ht20      = 4,
    htt_phy_mode_11ng_ht20      = 5,
    htt_phy_mode_11na_ht40      = 6,
    htt_phy_mode_11ng_ht40      = 7,
    htt_phy_mode_11ac_vht20     = 8,
    htt_phy_mode_11ac_vht40     = 9,
    htt_phy_mode_11ac_vht80     = 10,
    htt_phy_mode_11ac_vht20_2g  = 11,
    htt_phy_mode_11ac_vht40_2g  = 12,
    htt_phy_mode_11ac_vht80_2g  = 13,
    htt_phy_mode_11ac_vht80_80  = 14, /* 80+80 */
    htt_phy_mode_11ac_vht160    = 15,

    htt_phy_mode_max,
};

/**
 * @brief target -> host HTT channel change indication
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_CHAN_CHANGE
 *
 * @details
 *  Specify when a channel change occurs.
 *  This allows the host to precisely determine which rx frames arrived
 *  on the old channel and which rx frames arrived on the new channel.
 *
 *|31                                         |7       0 |
 *|-------------------------------------------+----------|
 *|                  reserved                 | msg type |
 *|------------------------------------------------------|
 *|              primary_chan_center_freq_mhz            |
 *|------------------------------------------------------|
 *|            contiguous_chan1_center_freq_mhz          |
 *|------------------------------------------------------|
 *|            contiguous_chan2_center_freq_mhz          |
 *|------------------------------------------------------|
 *|                        phy_mode                      |
 *|------------------------------------------------------|
 *
 * Header fields:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a htt channel change indication message
 *     Value: 0x15 (HTT_T2H_MSG_TYPE_CHAN_CHANGE)
 *   - PRIMARY_CHAN_CENTER_FREQ_MHZ
 *     Bits 31:0
 *     Purpose: identify the (center of the) new 20 MHz primary channel
 *     Value: center frequency of the 20 MHz primary channel, in MHz units
 *   - CONTIG_CHAN1_CENTER_FREQ_MHZ
 *     Bits 31:0
 *     Purpose: identify the (center of the) contiguous frequency range
 *         comprising the new channel.
 *         For example, if the new channel is a 80 MHz channel extending
 *         60 MHz beyond the primary channel, this field would be 30 larger
 *         than the primary channel center frequency field.
 *     Value: center frequency of the contiguous frequency range comprising
 *         the full channel in MHz units
 *         (80+80 channels also use the CONTIG_CHAN2 field)
 *   - CONTIG_CHAN2_CENTER_FREQ_MHZ
 *     Bits 31:0
 *     Purpose: Identify the (center of the) 80 MHz extension frequency range
 *         within a VHT 80+80 channel.
 *         This field is only relevant for VHT 80+80 channels.
 *     Value: center frequency of the 80 MHz extension channel in a VHT 80+80
 *         channel (arbitrary value for cases besides VHT 80+80)
 *   - PHY_MODE
 *     Bits 31:0
 *     Purpose: specify the PHY channel's type (legacy vs. HT vs. VHT), width,
 *         and band
 *     Value: htt_phy_mode enum value
 */

PREPACK struct htt_chan_change_t
{
    /* DWORD 0: flags and meta-data */
    A_UINT32
        msg_type:   8, /* HTT_T2H_MSG_TYPE_WDI_IPA_OP_RESPONSE */
        reserved1: 24;
    A_UINT32 primary_chan_center_freq_mhz;
    A_UINT32 contig_chan1_center_freq_mhz;
    A_UINT32 contig_chan2_center_freq_mhz;
    A_UINT32 phy_mode;
} POSTPACK;
/*
 * Due to historical / backwards-compatibility reasons, maintain the
 * below htt_chan_change_msg struct definition, which needs to be
 * consistent with the above htt_chan_change_t struct definition
 * (aside from the htt_chan_change_t definition including the msg_type
 * dword within the message, and the htt_chan_change_msg only containing
 * the payload of the message that follows the msg_type dword).
 */
PREPACK struct htt_chan_change_msg {
     A_UINT32 chan_mhz;   /* frequency in mhz */
     A_UINT32 band_center_freq1; /* Center frequency 1 in MHz */
     A_UINT32 band_center_freq2; /* Center frequency 2 in MHz - valid only for 11acvht 80plus80 mode*/
     A_UINT32 chan_mode;  /* WLAN_PHY_MODE of the channel defined in wlan_defs.h */
} POSTPACK;

#define HTT_CHAN_CHANGE_PRIMARY_CHAN_CENTER_FREQ_MHZ_M  0xffffffff
#define HTT_CHAN_CHANGE_PRIMARY_CHAN_CENTER_FREQ_MHZ_S  0
#define HTT_CHAN_CHANGE_CONTIG_CHAN1_CENTER_FREQ_MHZ_M  0xffffffff
#define HTT_CHAN_CHANGE_CONTIG_CHAN1_CENTER_FREQ_MHZ_S  0
#define HTT_CHAN_CHANGE_CONTIG_CHAN2_CENTER_FREQ_MHZ_M  0xffffffff
#define HTT_CHAN_CHANGE_CONTIG_CHAN2_CENTER_FREQ_MHZ_S  0
#define HTT_CHAN_CHANGE_PHY_MODE_M                      0xffffffff
#define HTT_CHAN_CHANGE_PHY_MODE_S                      0


#define HTT_CHAN_CHANGE_PRIMARY_CHAN_CENTER_FREQ_MHZ_SET(word, value)          \
    do {                                                                       \
        HTT_CHECK_SET_VAL(HTT_CHAN_CHANGE_PRIMARY_CHAN_CENTER_FREQ_MHZ, value);\
        (word) |= (value)  << HTT_CHAN_CHANGE_PRIMARY_CHAN_CENTER_FREQ_MHZ_S;  \
    } while (0)
#define HTT_CHAN_CHANGE_PRIMARY_CHAN_CENTER_FREQ_MHZ_GET(word) \
    (((word) & HTT_CHAN_CHANGE_PRIMARY_CHAN_CENTER_FREQ_MHZ_M) \
     >> HTT_CHAN_CHANGE_PRIMARY_CHAN_CENTER_FREQ_MHZ_S)

#define HTT_CHAN_CHANGE_CONTIG_CHAN1_CENTER_FREQ_MHZ_SET(word, value)          \
    do {                                                                       \
        HTT_CHECK_SET_VAL(HTT_CHAN_CHANGE_CONTIG_CHAN1_CENTER_FREQ_MHZ, value);\
        (word) |= (value)  << HTT_CHAN_CHANGE_CONTIG_CHAN1_CENTER_FREQ_MHZ_S;  \
    } while (0)
#define HTT_CHAN_CHANGE_CONTIG_CHAN1_CENTER_FREQ_MHZ_GET(word) \
    (((word) & HTT_CHAN_CHANGE_CONTIG_CHAN1_CENTER_FREQ_MHZ_M) \
     >> HTT_CHAN_CHANGE_CONTIG_CHAN1_CENTER_FREQ_MHZ_S)

#define HTT_CHAN_CHANGE_CONTIG_CHAN2_CENTER_FREQ_MHZ_SET(word, value)          \
    do {                                                                       \
        HTT_CHECK_SET_VAL(HTT_CHAN_CHANGE_CONTIG_CHAN2_CENTER_FREQ_MHZ, value);\
        (word) |= (value)  << HTT_CHAN_CHANGE_CONTIG_CHAN2_CENTER_FREQ_MHZ_S;  \
    } while (0)
#define HTT_CHAN_CHANGE_CONTIG_CHAN2_CENTER_FREQ_MHZ_GET(word) \
    (((word) & HTT_CHAN_CHANGE_CONTIG_CHAN2_CENTER_FREQ_MHZ_M) \
     >> HTT_CHAN_CHANGE_CONTIG_CHAN2_CENTER_FREQ_MHZ_S)

#define HTT_CHAN_CHANGE_PHY_MODE_SET(word, value)          \
    do {                                                                       \
        HTT_CHECK_SET_VAL(HTT_CHAN_CHANGE_PHY_MODE, value);\
        (word) |= (value)  << HTT_CHAN_CHANGE_PHY_MODE_S;  \
    } while (0)
#define HTT_CHAN_CHANGE_PHY_MODE_GET(word) \
    (((word) & HTT_CHAN_CHANGE_PHY_MODE_M) \
     >> HTT_CHAN_CHANGE_PHY_MODE_S)

#define HTT_CHAN_CHANGE_BYTES sizeof(struct htt_chan_change_t)


/**
 * @brief rx offload packet error message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RX_OFLD_PKT_ERR
 *
 * @details
 *  HTT_RX_OFLD_PKT_ERR message is sent by target to host to indicate err
 *  of target payload like mic err.
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |      tid       |     vdev_id    |  msg_sub_type  |    msg_type    |
 *     |-------------------------------------------------------------------|
 *     :                    (sub-type dependent content)                   :
 *     :- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -:
 * Header fields:
 *   - msg_type
 *     Bits 7:0
 *     Purpose: Identifies this as HTT_RX_OFLD_PKT_ERR message
 *     value: 0x16 (HTT_T2H_MSG_TYPE_RX_OFLD_PKT_ERR)
 *   - msg_sub_type
 *     Bits 15:8
 *     Purpose: Identifies which type of rx error is reported by this message
 *     value: htt_rx_ofld_pkt_err_type
 *   - vdev_id
 *     Bits 23:16
 *     Purpose: Identifies which vdev received the erroneous rx frame
 *     value:
 *   - tid
 *     Bits 31:24
 *     Purpose: Identifies the traffic type of the rx frame
 *     value:
 *
 *   - The payload fields used if the sub-type == MIC error are shown below.
 *     Note - MIC err is per MSDU, while PN is per MPDU.
 *     The FW will discard the whole MPDU if any MSDU within the MPDU is marked
 *     with MIC err in A-MSDU case, so FW will send only one HTT message
 *     with the PN of this MPDU attached to indicate MIC err for one MPDU
 *     instead of sending separate HTT messages for each wrong MSDU within
 *     the MPDU.
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |     Rsvd       |     key_id     |             peer_id             |
 *     |-------------------------------------------------------------------|
 *     |                        receiver MAC addr 31:0                     |
 *     |-------------------------------------------------------------------|
 *     |              Rsvd               |    receiver MAC addr 47:32      |
 *     |-------------------------------------------------------------------|
 *     |                     transmitter MAC addr 31:0                     |
 *     |-------------------------------------------------------------------|
 *     |              Rsvd               |    transmitter MAC addr 47:32   |
 *     |-------------------------------------------------------------------|
 *     |                              PN 31:0                              |
 *     |-------------------------------------------------------------------|
 *     |              Rsvd               |              PN 47:32           |
 *     |-------------------------------------------------------------------|
 *   - peer_id
 *     Bits 15:0
 *     Purpose: identifies which peer is frame is from
 *     value:
 *   - key_id
 *     Bits 23:16
 *     Purpose: identifies key_id of rx frame
 *     value:
 *   - RA_31_0 (receiver MAC addr 31:0)
 *     Bits 31:0
 *     Purpose: identifies by MAC address which vdev received the frame
 *     value: MAC address lower 4 bytes
 *   - RA_47_32 (receiver MAC addr 47:32)
 *     Bits 15:0
 *     Purpose: identifies by MAC address which vdev received the frame
 *     value: MAC address upper 2 bytes
 *   - TA_31_0 (transmitter MAC addr 31:0)
 *     Bits 31:0
 *     Purpose: identifies by MAC address which peer transmitted the frame
 *     value: MAC address lower 4 bytes
 *   - TA_47_32 (transmitter MAC addr 47:32)
 *     Bits 15:0
 *     Purpose: identifies by MAC address which peer transmitted the frame
 *     value: MAC address upper 2 bytes
 *   - PN_31_0
 *     Bits 31:0
 *     Purpose: Identifies pn of rx frame
 *     value: PN lower 4 bytes
 *   - PN_47_32
 *     Bits 15:0
 *     Purpose: Identifies pn of rx frame
 *     value:
 *         TKIP or CCMP: PN upper 2 bytes
 *         WAPI: PN bytes 6:5 (bytes 15:7 not included in this message)
 */

enum htt_rx_ofld_pkt_err_type {
    HTT_RX_OFLD_PKT_ERR_TYPE_NONE = 0,
    HTT_RX_OFLD_PKT_ERR_TYPE_MIC_ERR,
};

/* definition for HTT_RX_OFLD_PKT_ERR msg hdr */
#define HTT_RX_OFLD_PKT_ERR_HDR_BYTES 4

#define HTT_RX_OFLD_PKT_ERR_MSG_SUB_TYPE_M     0x0000ff00
#define HTT_RX_OFLD_PKT_ERR_MSG_SUB_TYPE_S     8

#define HTT_RX_OFLD_PKT_ERR_VDEV_ID_M          0x00ff0000
#define HTT_RX_OFLD_PKT_ERR_VDEV_ID_S          16

#define HTT_RX_OFLD_PKT_ERR_TID_M              0xff000000
#define HTT_RX_OFLD_PKT_ERR_TID_S              24

#define HTT_RX_OFLD_PKT_ERR_MSG_SUB_TYPE_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MSG_SUB_TYPE_M) \
    >> HTT_RX_OFLD_PKT_ERR_MSG_SUB_TYPE_S)
#define HTT_RX_OFLD_PKT_ERR_MSG_SUB_TYPE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MSG_SUB_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MSG_SUB_TYPE_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_VDEV_ID_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_VDEV_ID_M) >> HTT_RX_OFLD_PKT_ERR_VDEV_ID_S)
#define HTT_RX_OFLD_PKT_ERR_VDEV_ID_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_VDEV_ID, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_VDEV_ID_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_TID_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_TID_M) >> HTT_RX_OFLD_PKT_ERR_TID_S)
#define HTT_RX_OFLD_PKT_ERR_TID_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_TID, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_TID_S)); \
    } while (0)

/* definition for HTT_RX_OFLD_PKT_ERR_MIC_ERR msg sub-type payload */
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_BYTES   28

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PEER_ID_M          0x0000ffff
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PEER_ID_S          0

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_KEYID_M            0x00ff0000
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_KEYID_S            16

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_31_0_M          0xffffffff
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_31_0_S          0

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_47_32_M         0x0000ffff
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_47_32_S         0

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_31_0_M          0xffffffff
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_31_0_S          0

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_47_32_M         0x0000ffff
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_47_32_S         0

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_31_0_M          0xffffffff
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_31_0_S          0

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_47_32_M         0x0000ffff
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_47_32_S         0

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PEER_ID_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MIC_ERR_PEER_ID_M) >> \
    HTT_RX_OFLD_PKT_ERR_MIC_ERR_PEER_ID_S)
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PEER_ID_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MIC_ERR_PEER_ID, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MIC_ERR_PEER_ID_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_KEYID_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MIC_ERR_KEYID_M) >> \
    HTT_RX_OFLD_PKT_ERR_MIC_ERR_KEYID_S)
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_KEYID_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MIC_ERR_KEYID, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MIC_ERR_KEYID_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_31_0_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_31_0_M) >> \
    HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_31_0_S)
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_31_0_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_31_0, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_31_0_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_47_32_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_47_32_M) >> \
    HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_47_32_S)
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_47_32_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_47_32, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MIC_ERR_RA_47_32_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_31_0_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_31_0_M) >> \
    HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_31_0_S)
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_31_0_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_31_0, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_31_0_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_47_32_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_47_32_M) >> \
    HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_47_32_S)
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_47_32_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_47_32, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MIC_ERR_TA_47_32_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_31_0_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_31_0_M) >> \
    HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_31_0_S)
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_31_0_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_31_0, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_31_0_S)); \
    } while (0)

#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_47_32_GET(_var) \
    (((_var) & HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_47_32_M) >> \
    HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_47_32_S)
#define HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_47_32_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_47_32, _val);  \
        ((_var) |= ((_val) << HTT_RX_OFLD_PKT_ERR_MIC_ERR_PN_47_32_S)); \
    } while (0)

/**
 * @brief target -> host peer rate report message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_RATE_REPORT
 *
 * @details
 *  HTT_T2H_MSG_TYPE_RATE_REPORT message is sent by target to host to indicate the
 *  justified rate of all the peers.
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |           peer_count            |                |    msg_type    |
 *     |-------------------------------------------------------------------|
 *     :            Payload (variant number of peer rate report)           :
 *     :- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -:
 * Header fields:
 *   - msg_type
 *     Bits 7:0
 *     Purpose: Identifies this as HTT_T2H_MSG_TYPE_RATE_REPORT message.
 *     value: 0x17 (HTT_T2H_MSG_TYPE_RATE_REPORT)
 *   - reserved
 *     Bits 15:8
 *     Purpose:
 *     value:
 *   - peer_count
 *     Bits 31:16
 *     Purpose: Specify how many peer rate report elements are present in the payload.
 *     value:
 *
  * Payload:
 *     There are variant number of peer rate report follow the first 32 bits.
 *     The peer rate report is defined as follows.
 *
 *     |31                   20|19     16|15                              0|
 *     |-----------------------+---------+---------------------------------|-
 *     |        reserved       |   phy   |             peer_id             | \
 *     |-------------------------------------------------------------------|  -> report #0
 *     |                               rate                                | /
 *     |-----------------------+---------+---------------------------------|-
 *     |        reserved       |   phy   |             peer_id             | \
 *     |-------------------------------------------------------------------|  -> report #1
 *     |                               rate                                | /
 *     |-----------------------+---------+---------------------------------|-
 *     |        reserved       |   phy   |             peer_id             | \
 *     |-------------------------------------------------------------------|  -> report #2
 *     |                               rate                                | /
 *     |-------------------------------------------------------------------|-
 *     :                                                                   :
 *     :                                                                   :
 *     :                                                                   :
 *     :-------------------------------------------------------------------:
 *
 *   - peer_id
 *     Bits 15:0
 *     Purpose: identify the peer
 *     value:
 *   - phy
 *     Bits 19:16
 *     Purpose: identify which phy is in use
 *     value: 0=11b, 1=11a/g, 2=11n, 3=11ac.
 *         Please see enum htt_peer_report_phy_type for detail.
 *   - reserved
 *     Bits 31:20
 *     Purpose:
 *     value:
 *   - rate
 *     Bits 31:0
 *     Purpose: represent the justified rate of the peer specified by peer_id
 *     value:
 */

enum htt_peer_rate_report_phy_type {
    HTT_PEER_RATE_REPORT_11B = 0,
    HTT_PEER_RATE_REPORT_11A_G,
    HTT_PEER_RATE_REPORT_11N,
    HTT_PEER_RATE_REPORT_11AC,
};

#define HTT_PEER_RATE_REPORT_SIZE                8

#define HTT_PEER_RATE_REPORT_MSG_PEER_COUNT_M    0xffff0000
#define HTT_PEER_RATE_REPORT_MSG_PEER_COUNT_S    16

#define HTT_PEER_RATE_REPORT_MSG_PEER_ID_M       0x0000ffff
#define HTT_PEER_RATE_REPORT_MSG_PEER_ID_S       0

#define HTT_PEER_RATE_REPORT_MSG_PHY_M           0x000f0000
#define HTT_PEER_RATE_REPORT_MSG_PHY_S           16

#define HTT_PEER_RATE_REPORT_MSG_PEER_COUNT_GET(_var) \
    (((_var) & HTT_PEER_RATE_REPORT_MSG_PEER_COUNT_M) \
    >> HTT_PEER_RATE_REPORT_MSG_PEER_COUNT_S)
#define HTT_PEER_RATE_REPORT_MSG_PEER_COUNT_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_PEER_RATE_REPORT_MSG_PEER_COUNT, _val);  \
        ((_var) |= ((_val) << HTT_PEER_RATE_REPORT_MSG_PEER_COUNT_S)); \
    } while (0)

#define HTT_PEER_RATE_REPORT_MSG_PEER_ID_GET(_var) \
    (((_var) & HTT_PEER_RATE_REPORT_MSG_PEER_ID_M) \
    >> HTT_PEER_RATE_REPORT_MSG_PEER_ID_S)
#define HTT_PEER_RATE_REPORT_MSG_PEER_ID_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_PEER_RATE_REPORT_MSG_PEER_ID, _val);  \
        ((_var) |= ((_val) << HTT_PEER_RATE_REPORT_MSG_PEER_ID_S)); \
    } while (0)

#define HTT_PEER_RATE_REPORT_MSG_PHY_GET(_var) \
    (((_var) & HTT_PEER_RATE_REPORT_MSG_PHY_M) \
    >> HTT_PEER_RATE_REPORT_MSG_PHY_S)
#define HTT_PEER_RATE_REPORT_MSG_PHY_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_PEER_RATE_REPORT_MSG_PHY, _val);  \
        ((_var) |= ((_val) << HTT_PEER_RATE_REPORT_MSG_PHY_S)); \
    } while (0)

/**
 * @brief target -> host flow pool map message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_FLOW_POOL_MAP
 *
 * @details
 *  HTT_T2H_MSG_TYPE_FLOW_POOL_MAP message is sent by the target when setting up
 *  a flow of descriptors.
 *
 *  This message is in TLV format and indicates the parameters to be setup a
 *  flow in the host. Each entry indicates that a particular flow ID is ready to
 *  receive descriptors from a specified pool.
 *
 *  The message would appear as follows:
 *
 *         |31            24|23            16|15             8|7              0|
 *         |----------------+----------------+----------------+----------------|
 * header  |            reserved             |   num_flows    |     msg_type   |
 *         |-------------------------------------------------------------------|
 *         |                                                                   |
 *         :                              payload                              :
 *         |                                                                   |
 *         |-------------------------------------------------------------------|
 *
 * The header field is one DWORD long and is interpreted as follows:
 * b'0:7   - msg_type:  Set to 0x18 (HTT_T2H_MSG_TYPE_FLOW_POOL_MAP)
 * b'8-15  - num_flows: This will indicate the number of flows being setup in
 *                      this message
 * b'16-31 - reserved:  These bits are reserved for future use
 *
 * Payload:
 * The payload would contain multiple objects of the following structure. Each
 * object represents a flow.
 *
 *         |31            24|23            16|15             8|7              0|
 *         |----------------+----------------+----------------+----------------|
 * header  |            reserved             |   num_flows    |     msg_type   |
 *         |-------------------------------------------------------------------|
 * payload0|                             flow_type                             |
 *         |-------------------------------------------------------------------|
 *         |                              flow_id                              |
 *         |-------------------------------------------------------------------|
 *         |            reserved0            |          flow_pool_id           |
 *         |-------------------------------------------------------------------|
 *         |            reserved1            |         flow_pool_size          |
 *         |-------------------------------------------------------------------|
 *         |                             reserved2                             |
 *         |-------------------------------------------------------------------|
 * payload1|                             flow_type                             |
 *         |-------------------------------------------------------------------|
 *         |                              flow_id                              |
 *         |-------------------------------------------------------------------|
 *         |            reserved0            |          flow_pool_id           |
 *         |-------------------------------------------------------------------|
 *         |            reserved1            |         flow_pool_size          |
 *         |-------------------------------------------------------------------|
 *         |                             reserved2                             |
 *         |-------------------------------------------------------------------|
 *         |                                 .                                 |
 *         |                                 .                                 |
 *         |                                 .                                 |
 *         |-------------------------------------------------------------------|
 *
 * Each payload is 5 DWORDS long and is interpreted as follows:
 * dword0 - b'0:31  - flow_type: This indicates the type of the entity to which
 *                               this flow is associated. It can be VDEV, peer,
 *                               or tid (AC). Based on enum htt_flow_type.
 *
 * dword1 - b'0:31  - flow_id: Identifier for the flow corresponding to this
 *                             object. For flow_type vdev it is set to the
 *                             vdevid, for peer it is peerid and for tid, it is
 *                             tid_num.
 *
 * dword2 - b'0:15  - flow_pool_id: Identifier of the descriptor-pool being used
 *                                  in the host for this flow
 *          b'16:31 - reserved0: This field in reserved for the future. In case
 *                               we have a hierarchical implementation (HCM) of
 *                               pools, it can be used to indicate the ID of the
 *                               parent-pool.
 *
 * dword3 - b'0:15  - flow_pool_size: Size of the pool in number of descriptors.
 *                                    Descriptors for this flow will be
 *                                    allocated from this pool in the host.
 *          b'16:31 - reserved1: This field in reserved for the future. In case
 *                               we have a hierarchical implementation of pools,
 *                               it can be used to indicate the max number of
 *                               descriptors in the pool. The b'0:15 can be used
 *                               to indicate min number of descriptors in the
 *                               HCM scheme.
 *
 * dword4 - b'0:31  - reserved2: This field in reserved for the future. In case
 *                               we have a hierarchical implementation of pools,
 *                               b'0:15 can be used to indicate the
 *                               priority-based borrowing (PBB) threshold of
 *                               the flow's pool. The b'16:31 are still left
 *                               reserved.
 */

enum htt_flow_type {
    FLOW_TYPE_VDEV = 0,
    /* Insert new flow types above this line */
};

PREPACK struct htt_flow_pool_map_payload_t {
    A_UINT32 flow_type;
    A_UINT32 flow_id;
    A_UINT32 flow_pool_id:16,
             reserved0:16;
    A_UINT32 flow_pool_size:16,
             reserved1:16;
    A_UINT32 reserved2;
} POSTPACK;

#define HTT_FLOW_POOL_MAP_HEADER_SZ    (sizeof(A_UINT32))

#define HTT_FLOW_POOL_MAP_PAYLOAD_SZ    \
    (sizeof(struct htt_flow_pool_map_payload_t))

#define HTT_FLOW_POOL_MAP_NUM_FLOWS_M                    0x0000ff00
#define HTT_FLOW_POOL_MAP_NUM_FLOWS_S                    8

#define HTT_FLOW_POOL_MAP_FLOW_TYPE_M                    0xffffffff
#define HTT_FLOW_POOL_MAP_FLOW_TYPE_S                    0

#define HTT_FLOW_POOL_MAP_FLOW_ID_M                      0xffffffff
#define HTT_FLOW_POOL_MAP_FLOW_ID_S                      0

#define HTT_FLOW_POOL_MAP_FLOW_POOL_ID_M                 0x0000ffff
#define HTT_FLOW_POOL_MAP_FLOW_POOL_ID_S                 0

#define HTT_FLOW_POOL_MAP_FLOW_POOL_SIZE_M               0x0000ffff
#define HTT_FLOW_POOL_MAP_FLOW_POOL_SIZE_S               0

#define HTT_FLOW_POOL_MAP_NUM_FLOWS_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_MAP_NUM_FLOWS_M) >> HTT_FLOW_POOL_MAP_NUM_FLOWS_S)

#define HTT_FLOW_POOL_MAP_FLOW_TYPE_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_MAP_FLOW_TYPE_M) >> HTT_FLOW_POOL_MAP_FLOW_TYPE_S)

#define HTT_FLOW_POOL_MAP_FLOW_ID_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_MAP_FLOW_ID_M) >> HTT_FLOW_POOL_MAP_FLOW_ID_S)

#define HTT_FLOW_POOL_MAP_FLOW_POOL_ID_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_MAP_FLOW_POOL_ID_M) >> \
            HTT_FLOW_POOL_MAP_FLOW_POOL_ID_S)

#define HTT_FLOW_POOL_MAP_FLOW_POOL_SIZE_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_MAP_FLOW_POOL_SIZE_M) >> \
            HTT_FLOW_POOL_MAP_FLOW_POOL_SIZE_S)

#define HTT_FLOW_POOL_MAP_NUM_FLOWS_SET(_var, _val)            \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_MAP_NUM_FLOWS, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_MAP_NUM_FLOWS_S)); \
    } while (0)

#define HTT_FLOW_POOL_MAP_FLOW_TYPE_SET(_var, _val)            \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_MAP_FLOW_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_MAP_FLOW_TYPE_S)); \
    } while (0)

#define HTT_FLOW_POOL_MAP_FLOW_ID_SET(_var, _val)            \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_MAP_FLOW_ID, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_MAP_FLOW_ID_S)); \
    } while (0)

#define HTT_FLOW_POOL_MAP_FLOW_POOL_ID_SET(_var, _val)            \
    do {                                                          \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_MAP_FLOW_POOL_ID, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_MAP_FLOW_POOL_ID_S)); \
    } while (0)

#define HTT_FLOW_POOL_MAP_FLOW_POOL_SIZE_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_MAP_FLOW_POOL_SIZE, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_MAP_FLOW_POOL_SIZE_S)); \
    } while (0)

/**
 * @brief target -> host flow pool unmap message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_FLOW_POOL_UNMAP
 *
 * @details
 *  HTT_T2H_MSG_TYPE_FLOW_POOL_UNMAP message is sent by the target when tearing
 *  down a flow of descriptors.
 *  This message indicates that for the flow (whose ID is provided) is wanting
 *  to stop receiving descriptors. This flow ID corresponds to the ID of the
 *  pool of descriptors from where descriptors are being allocated for this
 *  flow. When a flow (and its pool) are unmapped, all the child-pools will also
 *  be unmapped by the host.
 *
 *  The message would appear as follows:
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |                     reserved0                    |     msg_type   |
 *     |-------------------------------------------------------------------|
 *     |                             flow_type                             |
 *     |-------------------------------------------------------------------|
 *     |                              flow_id                              |
 *     |-------------------------------------------------------------------|
 *     |             reserved1           |         flow_pool_id            |
 *     |-------------------------------------------------------------------|
 *
 *  The message is interpreted as follows:
 *  dword0 - b'0:7   - msg_type: This will be set to 0x19
 *                               (HTT_T2H_MSG_TYPE_FLOW_POOL_UNMAP)
 *           b'8:31  - reserved0: Reserved for future use
 *
 *  dword1 - b'0:31  - flow_type: This indicates the type of the entity to which
 *                                this flow is associated. It can be VDEV, peer,
 *                                or tid (AC). Based on enum htt_flow_type.
 *
 *  dword2 - b'0:31  - flow_id: Identifier for the flow corresponding to this
 *                              object. For flow_type vdev it is set to the
 *                              vdevid, for peer it is peerid and for tid, it is
 *                              tid_num.
 *
 *  dword3 - b'0:15  - flow_pool_id: Identifier of the descriptor-pool being
 *                                   used in the host for this flow
 *           b'16:31 - reserved0: This field in reserved for the future.
 *
 */

PREPACK struct htt_flow_pool_unmap_t {
    A_UINT32 msg_type:8,
             reserved0:24;
    A_UINT32 flow_type;
    A_UINT32 flow_id;
    A_UINT32 flow_pool_id:16,
             reserved1:16;
} POSTPACK;

#define HTT_FLOW_POOL_UNMAP_SZ  (sizeof(struct htt_flow_pool_unmap_t))

#define HTT_FLOW_POOL_UNMAP_FLOW_TYPE_M         0xffffffff
#define HTT_FLOW_POOL_UNMAP_FLOW_TYPE_S         0

#define HTT_FLOW_POOL_UNMAP_FLOW_ID_M           0xffffffff
#define HTT_FLOW_POOL_UNMAP_FLOW_ID_S           0

#define HTT_FLOW_POOL_UNMAP_FLOW_POOL_ID_M      0x0000ffff
#define HTT_FLOW_POOL_UNMAP_FLOW_POOL_ID_S      0

#define HTT_FLOW_POOL_UNMAP_FLOW_TYPE_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_UNMAP_FLOW_TYPE_M) >> \
            HTT_FLOW_POOL_UNMAP_FLOW_TYPE_S)

#define HTT_FLOW_POOL_UNMAP_FLOW_ID_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_UNMAP_FLOW_ID_M) >> HTT_FLOW_POOL_UNMAP_FLOW_ID_S)

#define HTT_FLOW_POOL_UNMAP_FLOW_POOL_ID_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_UNMAP_FLOW_POOL_ID_M) >> \
            HTT_FLOW_POOL_UNMAP_FLOW_POOL_ID_S)

#define HTT_FLOW_POOL_UNMAP_FLOW_TYPE_SET(_var, _val)            \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_UNMAP_FLOW_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_UNMAP_FLOW_TYPE_S)); \
    } while (0)

#define HTT_FLOW_POOL_UNMAP_FLOW_ID_SET(_var, _val)            \
    do {                                                       \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_UNMAP_FLOW_ID, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_UNMAP_FLOW_ID_S)); \
    } while (0)

#define HTT_FLOW_POOL_UNMAP_FLOW_POOL_ID_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_UNMAP_FLOW_POOL_ID, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_UNMAP_FLOW_POOL_ID_S)); \
    } while (0)


/**
 * @brief target -> host SRING setup done message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_SRING_SETUP_DONE
 *
 * @details
 *  HTT_T2H_MSG_TYPE_SRING_SETUP_DONE message is sent by the target when
 *  SRNG ring setup is done
 *
 *  This message indicates whether the last setup operation is successful.
 *  It will be sent to host when host set respose_required bit in
 *  HTT_H2T_MSG_TYPE_SRING_SETUP.
 *  The message would appear as follows:
 *
 *     |31            24|23            16|15             8|7              0|
 *     |--------------- +----------------+----------------+----------------|
 *     |  setup_status  |   ring_id      |   pdev_id     |      msg_type   |
 *     |-------------------------------------------------------------------|
 *
 * The message is interpreted as follows:
 * dword0 - b'0:7   - msg_type: This will be set to 0x1a
 *                    (HTT_T2H_MSG_TYPE_SRING_SETUP_DONE)
 *          b'8:15  - pdev_id:
 *                    0 (for rings at SOC/UMAC level),
 *                    1/2/3 mac id (for rings at LMAC level)
 *          b'16:23 - ring_id: Identify the ring which is set up
 *                    More details can be got from enum htt_srng_ring_id
 *          b'24:31 - setup_status:  Indicate status of setup operation
 *                    Refer to htt_ring_setup_status
 */

PREPACK struct htt_sring_setup_done_t {
    A_UINT32 msg_type:      8,
             pdev_id:       8,
             ring_id:       8,
             setup_status:  8;
} POSTPACK;

enum htt_ring_setup_status {
     htt_ring_setup_status_ok = 0,
     htt_ring_setup_status_error,
};

#define HTT_SRING_SETUP_DONE_SZ    (sizeof(struct htt_sring_setup_done_t))

#define HTT_SRING_SETUP_DONE_PDEV_ID_M                  0x0000ff00
#define HTT_SRING_SETUP_DONE_PDEV_ID_S                  8
#define HTT_SRING_SETUP_DONE_PDEV_ID_GET(_var) \
    (((_var) & HTT_SRING_SETUP_DONE_PDEV_ID_M) >> \
            HTT_SRING_SETUP_DONE_PDEV_ID_S)
#define HTT_SRING_SETUP_DONE_PDEV_ID_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_SRING_SETUP_DONE_PDEV_ID, _val); \
        ((_var) |= ((_val) << HTT_SRING_SETUP_DONE_PDEV_ID_S)); \
    } while (0)

#define HTT_SRING_SETUP_DONE_RING_ID_M                  0x00ff0000
#define HTT_SRING_SETUP_DONE_RING_ID_S                  16
#define HTT_SRING_SETUP_DONE_RING_ID_GET(_var) \
    (((_var) & HTT_SRING_SETUP_DONE_RING_ID_M) >> \
            HTT_SRING_SETUP_DONE_RING_ID_S)
#define HTT_SRING_SETUP_DONE_RING_ID_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_SRING_SETUP_DONE_RING_ID, _val); \
        ((_var) |= ((_val) << HTT_SRING_SETUP_DONE_RING_ID_S)); \
    } while (0)

#define HTT_SRING_SETUP_DONE_STATUS_M                   0xff000000
#define HTT_SRING_SETUP_DONE_STATUS_S                   24
#define HTT_SRING_SETUP_DONE_STATUS_GET(_var) \
    (((_var) & HTT_SRING_SETUP_DONE_STATUS_M) >> \
            HTT_SRING_SETUP_DONE_STATUS_S)
#define HTT_SRING_SETUP_DONE_STATUS_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_SRING_SETUP_DONE_STATUS, _val); \
        ((_var) |= ((_val) << HTT_SRING_SETUP_DONE_STATUS_S)); \
    } while (0)


/**
 * @brief target -> flow map flow info
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_MAP_FLOW_INFO
 *
 * @details
 *  HTT TX map flow entry with tqm flow pointer
 *  Sent from firmware to host to add tqm flow pointer in corresponding
 *  flow search entry. Flow metadata is replayed back to host as part of this
 *  struct to enable host to find the specific flow search entry
 *
 *  The message would appear as follows:
 *
 *     |31   28|27                 18|17     14|13       8|7              0|
 *     |-------+------------------------------------------+----------------|
 *     | rsvd0 |               fse_hsh_idx                |    msg_type    |
 *     |-------------------------------------------------------------------|
 *     |          rsvd1              |   tid   |         peer_id           |
 *     |-------------------------------------------------------------------|
 *     |                          tqm_flow_pntr_lo                         |
 *     |-------------------------------------------------------------------|
 *     |                          tqm_flow_pntr_hi                         |
 *     |-------------------------------------------------------------------|
 *     |                          fse_meta_data                            |
 *     |-------------------------------------------------------------------|
 *
 *  The message is interpreted as follows:
 *
 *  dword0 - b'0:7   - msg_type: This will be set to 0x1b
 *                     (HTT_T2H_MSG_TYPE_MAP_FLOW_INFO)
 *
 *  dword0 - b'8:27  - fse_hsh_idx: Flow search table index provided by host
 *                                  for this flow entry
 *
 *  dword0 - b'28:31 - rsvd0: Reserved for future use
 *
 *  dword1 - b'0:13  - peer_id: Software peer id given by host during association
 *
 *  dword1 - b'14:17 - tid
 *
 *  dword1 - b'18:31 - rsvd1: Reserved for future use
 *
 *  dword2 - b'0:31  - tqm_flow_pntr_lo: Lower 32 bits of TQM flow pointer
 *
 *  dword3 - b'0:31  - tqm_flow_pntr_hi: Higher 32 bits of TQM flow pointer
 *
 *  dword4 - b'0:31  - fse_meta_data: Replay back TX flow search metadata
 *                     given by host
 */
PREPACK struct htt_tx_map_flow_info {
    A_UINT32
        msg_type:    8,
        fse_hsh_idx: 20,
        rsvd0:       4;
    A_UINT32
        peer_id:     14,
        tid:         4,
        rsvd1:       14;
    A_UINT32 tqm_flow_pntr_lo;
    A_UINT32 tqm_flow_pntr_hi;
    struct htt_tx_flow_metadata fse_meta_data;
} POSTPACK;

/* DWORD 0 */
#define HTT_TX_MAP_FLOW_INFO_FSE_HSH_IDX_M                  0x0fffff00
#define HTT_TX_MAP_FLOW_INFO_FSE_HSH_IDX_S                  8

/* DWORD 1 */
#define HTT_TX_MAP_FLOW_INFO_PEER_ID_M                      0x00003fff
#define HTT_TX_MAP_FLOW_INFO_PEER_ID_S                      0
#define HTT_TX_MAP_FLOW_INFO_TID_M                          0x0003c000
#define HTT_TX_MAP_FLOW_INFO_TID_S                          14

/* DWORD 0 */
#define HTT_TX_MAP_FLOW_INFO_FSE_HSH_IDX_GET(_var) \
    (((_var) & HTT_TX_MAP_FLOW_INFO_FSE_HSH_IDX_M) >> \
    HTT_TX_MAP_FLOW_INFO_FSE_HSH_IDX_S)
#define HTT_TX_MAP_FLOW_INFO_FSE_HSH_IDX_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MAP_FLOW_INFO_FSE_HSH_IDX, _val); \
         ((_var) |= ((_val) << HTT_TX_MAP_FLOW_INFO_FSE_HSH_IDX_S)); \
     } while (0)

/* DWORD 1 */
#define HTT_TX_MAP_FLOW_INFO_PEER_ID_GET(_var) \
    (((_var) & HTT_TX_MAP_FLOW_INFO_PEER_ID_M) >> \
    HTT_TX_MAP_FLOW_INFO_PEER_ID_S)
#define HTT_TX_MAP_FLOW_INFO_PEER_ID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MAP_FLOW_INFO_PEER_ID_IDX, _val); \
         ((_var) |= ((_val) << HTT_TX_MAP_FLOW_INFO_PEER_ID_S)); \
     } while (0)

#define HTT_TX_MAP_FLOW_INFO_TID_GET(_var) \
    (((_var) & HTT_TX_MAP_FLOW_INFO_TID_M) >> \
    HTT_TX_MAP_FLOW_INFO_TID_S)
#define HTT_TX_MAP_FLOW_INFO_TID_SET(_var, _val) \
     do { \
         HTT_CHECK_SET_VAL(HTT_TX_MAP_FLOW_INFO_TID_IDX, _val); \
         ((_var) |= ((_val) << HTT_TX_MAP_FLOW_INFO_TID_S)); \
     } while (0)


/*
 * htt_dbg_ext_stats_status -
 * present -     The requested stats have been delivered in full.
 *               This indicates that either the stats information was contained
 *               in its entirety within this message, or else this message
 *               completes the delivery of the requested stats info that was
 *               partially delivered through earlier STATS_CONF messages.
 * partial -     The requested stats have been delivered in part.
 *               One or more subsequent STATS_CONF messages with the same
 *               cookie value will be sent to deliver the remainder of the
 *               information.
 * error -       The requested stats could not be delivered, for example due
 *               to a shortage of memory to construct a message holding the
 *               requested stats.
 * invalid -     The requested stat type is either not recognized, or the
 *               target is configured to not gather the stats type in question.
 */
enum htt_dbg_ext_stats_status {
    HTT_DBG_EXT_STATS_STATUS_PRESENT = 0,
    HTT_DBG_EXT_STATS_STATUS_PARTIAL = 1,
    HTT_DBG_EXT_STATS_STATUS_ERROR   = 2,
    HTT_DBG_EXT_STATS_STATUS_INVALID = 3,
};

/**
 * @brief target -> host ppdu stats upload
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_PPDU_STATS_IND
 *
 * @details
 * The following field definitions describe the format of the HTT target
 * to host ppdu stats indication message.
 *
 *
 * |31                         16|15   12|11   10|9      8|7            0 |
 * |----------------------------------------------------------------------|
 * |    payload_size             | rsvd  |pdev_id|mac_id  |    msg type   |
 * |----------------------------------------------------------------------|
 * |                          ppdu_id                                     |
 * |----------------------------------------------------------------------|
 * |                        Timestamp in us                               |
 * |----------------------------------------------------------------------|
 * |                          reserved                                    |
 * |----------------------------------------------------------------------|
 * |                    type-specific stats info                          |
 * |                     (see htt_ppdu_stats.h)                           |
 * |----------------------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Purpose: Identifies this is a PPDU STATS indication
 *             message.
 *    Value: 0x1d (HTT_T2H_MSG_TYPE_PPDU_STATS_IND)
 *  - mac_id
 *    Bits 9:8
 *    Purpose: mac_id of this ppdu_id
 *    Value: 0-3
 *  - pdev_id
 *    Bits 11:10
 *    Purpose: pdev_id of this ppdu_id
 *    Value: 0-3
 *     0 (for rings at SOC level),
 *     1/2/3 PDEV -> 0/1/2
 *  - payload_size
 *    Bits 31:16
 *    Purpose: total tlv size
 *    Value: payload_size in bytes
 */
#define HTT_T2H_PPDU_STATS_IND_HDR_SIZE       16

#define HTT_T2H_PPDU_STATS_MAC_ID_M           0x00000300
#define HTT_T2H_PPDU_STATS_MAC_ID_S           8

#define HTT_T2H_PPDU_STATS_PDEV_ID_M          0x00000C00
#define HTT_T2H_PPDU_STATS_PDEV_ID_S          10

#define HTT_T2H_PPDU_STATS_PAYLOAD_SIZE_M     0xFFFF0000
#define HTT_T2H_PPDU_STATS_PAYLOAD_SIZE_S     16

#define HTT_T2H_PPDU_STATS_PPDU_ID_M          0xFFFFFFFF
#define HTT_T2H_PPDU_STATS_PPDU_ID_S          0

#define HTT_T2H_PPDU_STATS_MAC_ID_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_PPDU_STATS_MAC_ID, value);   \
        (word) |= (value)  << HTT_T2H_PPDU_STATS_MAC_ID_S;     \
    } while (0)
#define HTT_T2H_PPDU_STATS_MAC_ID_GET(word) \
    (((word) & HTT_T2H_PPDU_STATS_MAC_ID_M) >> \
    HTT_T2H_PPDU_STATS_MAC_ID_S)

#define HTT_T2H_PPDU_STATS_PDEV_ID_SET(word, value)             \
    do {                                                        \
        HTT_CHECK_SET_VAL(HTT_T2H_PPDU_STATS_PDEV_ID, value);   \
        (word) |= (value)  << HTT_T2H_PPDU_STATS_PDEV_ID_S;     \
    } while (0)
#define HTT_T2H_PPDU_STATS_PDEV_ID_GET(word) \
    (((word) & HTT_T2H_PPDU_STATS_PDEV_ID_M) >> \
    HTT_T2H_PPDU_STATS_PDEV_ID_S)

#define HTT_T2H_PPDU_STATS_PAYLOAD_SIZE_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_PPDU_STATS_PAYLOAD_SIZE, value);   \
        (word) |= (value)  << HTT_T2H_PPDU_STATS_PAYLOAD_SIZE_S;     \
    } while (0)
#define HTT_T2H_PPDU_STATS_PAYLOAD_SIZE_GET(word) \
    (((word) & HTT_T2H_PPDU_STATS_PAYLOAD_SIZE_M) >> \
    HTT_T2H_PPDU_STATS_PAYLOAD_SIZE_S)

#define HTT_T2H_PPDU_STATS_PPDU_ID_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_PPDU_STATS_PPDU_ID, value);   \
        (word) |= (value)  << HTT_T2H_PPDU_STATS_PPDU_ID_S;     \
    } while (0)
#define HTT_T2H_PPDU_STATS_PPDU_ID_GET(word) \
    (((word) & HTT_T2H_PPDU_STATS_PPDU_ID_M) >> \
    HTT_T2H_PPDU_STATS_PPDU_ID_S)

/* htt_t2h_ppdu_stats_ind_hdr_t
 * This struct contains the fields within the header of the
 * HTT_T2H_PPDU_STATS_IND message, preceding the type-specific
 * stats info.
 * This struct assumes little-endian layout, and thus is only
 * suitable for use within processors known to be little-endian
 * (such as the target).
 * In contrast, the above macros provide endian-portable methods
 * to get and set the bitfields within this PPDU_STATS_IND header.
 */
typedef struct {
    A_UINT32 msg_type:      8, /* bits  7:0 */
             mac_id:        2, /* bits  9:8 */
             pdev_id:       2, /* bits 11:10 */
             reserved1:     4, /* bits 15:12 */
             payload_size: 16; /* bits 31:16 */
    A_UINT32 ppdu_id;
    A_UINT32 timestamp_us;
    A_UINT32 reserved2;
} htt_t2h_ppdu_stats_ind_hdr_t;

/**
 * @brief target -> host extended statistics upload
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_EXT_STATS_CONF
 *
 * @details
 * The following field definitions describe the format of the HTT target
 * to host stats upload confirmation message.
 * The message contains a cookie echoed from the HTT host->target stats
 * upload request, which identifies which request the confirmation is
 * for, and a single stats can span over multiple HTT stats indication
 * due to the HTT message size limitation so every HTT ext stats indication
 * will have tag-length-value stats information elements.
 * The tag-length header for each HTT stats IND message also includes a
 * status field, to indicate whether the request for the stat type in
 * question was fully met, partially met, unable to be met, or invalid
 * (if the stat type in question is disabled in the target).
 * A Done bit 1's indicate the end of the of stats info elements.
 *
 *
 * |31                         16|15    12|11|10 8|7   5|4       0|
 * |--------------------------------------------------------------|
 * |                   reserved                   |    msg type   |
 * |--------------------------------------------------------------|
 * |                         cookie LSBs                          |
 * |--------------------------------------------------------------|
 * |                         cookie MSBs                          |
 * |--------------------------------------------------------------|
 * |      stats entry length     | rsvd   | D|  S |   stat type   |
 * |--------------------------------------------------------------|
 * |                   type-specific stats info                   |
 * |                      (see htt_stats.h)                       |
 * |--------------------------------------------------------------|
 * Header fields:
 *  - MSG_TYPE
 *    Bits 7:0
 *    Purpose: Identifies this is a extended statistics upload confirmation
 *             message.
 *    Value: 0x1c (HTT_T2H_MSG_TYPE_EXT_STATS_CONF)
 *  - COOKIE_LSBS
 *    Bits 31:0
 *    Purpose: Provide a mechanism to match a target->host stats confirmation
 *        message with its preceding host->target stats request message.
 *    Value: LSBs of the opaque cookie specified by the host-side requestor
 *  - COOKIE_MSBS
 *    Bits 31:0
 *    Purpose: Provide a mechanism to match a target->host stats confirmation
 *        message with its preceding host->target stats request message.
 *    Value: MSBs of the opaque cookie specified by the host-side requestor
 *
 * Stats Information Element tag-length header fields:
 *  - STAT_TYPE
 *    Bits 7:0
 *    Purpose: identifies the type of statistics info held in the
 *        following information element
 *    Value: htt_dbg_ext_stats_type
 *  - STATUS
 *    Bits 10:8
 *    Purpose: indicate whether the requested stats are present
 *    Value: htt_dbg_ext_stats_status
 *  - DONE
 *    Bits 11
 *    Purpose:
 *        Indicates the completion of the stats entry, this will be the last
 *        stats conf HTT segment for the requested stats type.
 *    Value:
 *        0 -> the stats retrieval is ongoing
 *        1 -> the stats retrieval is complete
 *  - LENGTH
 *    Bits 31:16
 *    Purpose: indicate the stats information size
 *    Value: This field specifies the number of bytes of stats information
 *       that follows the element tag-length header.
 *       It is expected but not required that this length is a multiple of
 *       4 bytes.
 */
#define HTT_T2H_EXT_STATS_COOKIE_SIZE         8

#define HTT_T2H_EXT_STATS_CONF_HDR_SIZE       4

#define HTT_T2H_EXT_STATS_CONF_TLV_HDR_SIZE   4

#define HTT_T2H_EXT_STATS_CONF_TLV_TYPE_M     0x000000ff
#define HTT_T2H_EXT_STATS_CONF_TLV_TYPE_S     0
#define HTT_T2H_EXT_STATS_CONF_TLV_STATUS_M   0x00000700
#define HTT_T2H_EXT_STATS_CONF_TLV_STATUS_S   8
#define HTT_T2H_EXT_STATS_CONF_TLV_DONE_M     0x00000800
#define HTT_T2H_EXT_STATS_CONF_TLV_DONE_S     11
#define HTT_T2H_EXT_STATS_CONF_TLV_LENGTH_M   0xffff0000
#define HTT_T2H_EXT_STATS_CONF_TLV_LENGTH_S   16

#define HTT_T2H_EXT_STATS_CONF_TLV_TYPE_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_EXT_STATS_CONF_TLV_TYPE, value);   \
        (word) |= (value)  << HTT_T2H_EXT_STATS_CONF_TLV_TYPE_S;     \
    } while (0)
#define HTT_T2H_EXT_STATS_CONF_TLV_TYPE_GET(word) \
    (((word) & HTT_T2H_EXT_STATS_CONF_TLV_TYPE_M) >> \
    HTT_T2H_EXT_STATS_CONF_TLV_TYPE_S)

#define HTT_T2H_EXT_STATS_CONF_TLV_STATUS_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_EXT_STATS_CONF_TLV_STATUS, value);   \
        (word) |= (value)  << HTT_T2H_EXT_STATS_CONF_TLV_STATUS_S;     \
    } while (0)
#define HTT_T2H_EXT_STATS_CONF_TLV_STATUS_GET(word) \
    (((word) & HTT_T2H_EXT_STATS_CONF_TLV_STATUS_M) >> \
    HTT_T2H_EXT_STATS_CONF_TLV_STATUS_S)

#define HTT_T2H_EXT_STATS_CONF_TLV_DONE_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_EXT_STATS_CONF_TLV_DONE, value);   \
        (word) |= (value)  << HTT_T2H_EXT_STATS_CONF_TLV_DONE_S;     \
    } while (0)
#define HTT_T2H_EXT_STATS_CONF_TLV_DONE_GET(word) \
    (((word) & HTT_T2H_EXT_STATS_CONF_TLV_DONE_M) >> \
    HTT_T2H_EXT_STATS_CONF_TLV_DONE_S)

#define HTT_T2H_EXT_STATS_CONF_TLV_LENGTH_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_EXT_STATS_CONF_TLV_LENGTH, value);   \
        (word) |= (value)  << HTT_T2H_EXT_STATS_CONF_TLV_LENGTH_S;     \
    } while (0)
#define HTT_T2H_EXT_STATS_CONF_TLV_LENGTH_GET(word) \
    (((word) & HTT_T2H_EXT_STATS_CONF_TLV_LENGTH_M) >> \
    HTT_T2H_EXT_STATS_CONF_TLV_LENGTH_S)

typedef enum {
    HTT_PEER_TYPE_DEFAULT = 0,    /* Generic/Non-BSS/Self Peer */
    HTT_PEER_TYPE_BSS = 1,        /* Peer is BSS Peer entry */
    HTT_PEER_TYPE_TDLS = 2,       /* Peer is a TDLS Peer */
    HTT_PEER_TYPE_OCB = 3,        /* Peer is a OCB Peer */
    HTT_PEER_TYPE_NAN_DATA = 4,   /* Peer is NAN DATA */
    HTT_PEER_TYPE_HOST_MAX = 127, /* Host <-> Target Peer type is assigned up to 127 */
                              /* Reserved from 128 - 255 for target internal use.*/
    HTT_PEER_TYPE_ROAMOFFLOAD_TEMP = 128, /* Temporarily created during offload roam */
} HTT_PEER_TYPE;

/** macro to convert MAC address from char array to HTT word format */
#define HTT_CHAR_ARRAY_TO_MAC_ADDR(c_macaddr, phtt_mac_addr)  do { \
    (phtt_mac_addr)->mac_addr31to0 = \
       (((c_macaddr)[0] <<  0) | \
        ((c_macaddr)[1] <<  8) | \
        ((c_macaddr)[2] << 16) | \
        ((c_macaddr)[3] << 24)); \
    (phtt_mac_addr)->mac_addr47to32 = ((c_macaddr)[4] | ((c_macaddr)[5] << 8));\
   } while (0)

/**
 * @brief target -> host monitor mac header indication message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_MONITOR_MAC_HEADER_IND
 *
 * @details
 * The following diagram shows the format of the monitor mac header message
 * sent from the target to the host.
 * This message is primarily sent when promiscuous rx mode is enabled.
 * One message is sent per rx PPDU.
 *
 *          |31          24|23           16|15            8|7            0|
 *          |-------------------------------------------------------------|
 *          |            peer_id           |    reserved0  |    msg_type  |
 *          |-------------------------------------------------------------|
 *          |            reserved1         |           num_mpdu           |
 *          |-------------------------------------------------------------|
 *          |                       struct hw_rx_desc                     |
 *          |                      (see wal_rx_desc.h)                    |
 *          |-------------------------------------------------------------|
 *          |                   struct ieee80211_frame_addr4              |
 *          |                      (see ieee80211_defs.h)                 |
 *          |-------------------------------------------------------------|
 *          |                   struct ieee80211_frame_addr4              |
 *          |                      (see ieee80211_defs.h)                 |
 *          |-------------------------------------------------------------|
 *          |                            ......                           |
 *          |-------------------------------------------------------------|
 *
 * Header fields:
 *  - msg_type
 *    Bits 7:0
 *    Purpose: Identifies this is a monitor mac header indication message.
 *    Value: 0x20 (HTT_T2H_MSG_TYPE_MONITOR_MAC_HEADER_IND)
 *  - peer_id
 *    Bits 31:16
 *    Purpose: Software peer id given by host during association,
 *             During promiscuous mode, the peer ID will be invalid (0xFF)
 *             for rx PPDUs received from unassociated peers.
 *    Value: peer ID (for associated peers) or 0xFF (for unassociated peers)
 *  - num_mpdu
 *    Bits 15:0
 *    Purpose: The number of MPDU frame headers (struct ieee80211_frame_addr4)
 *             delivered within the message.
 *    Value: 1 to 32
 *           num_mpdu is limited to a maximum value of 32, due to buffer
 *           size limits.  For PPDUs with more than 32 MPDUs, only the
 *           ieee80211_frame_addr4 headers from the first 32 MPDUs within
 *           the PPDU will be provided.
 */
#define HTT_T2H_MONITOR_MAC_HEADER_IND_HDR_SIZE       8

#define HTT_T2H_MONITOR_MAC_HEADER_PEER_ID_M          0xFFFF0000
#define HTT_T2H_MONITOR_MAC_HEADER_PEER_ID_S          16

#define HTT_T2H_MONITOR_MAC_HEADER_NUM_MPDU_M         0x0000FFFF
#define HTT_T2H_MONITOR_MAC_HEADER_NUM_MPDU_S         0


#define HTT_T2H_MONITOR_MAC_HEADER_PEER_ID_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_MONITOR_MAC_HEADER_PEER_ID, value);   \
        (word) |= (value)  << HTT_T2H_MONITOR_MAC_HEADER_PEER_ID_S;     \
    } while (0)
#define HTT_T2H_MONITOR_MAC_HEADER_PEER_ID_GET(word) \
    (((word) & HTT_T2H_MONITOR_MAC_HEADER_PEER_ID_M) >> \
    HTT_T2H_MONITOR_MAC_HEADER_PEER_ID_S)

#define HTT_T2H_MONITOR_MAC_HEADER_NUM_MPDU_SET(word, value)             \
    do {                                                         \
        HTT_CHECK_SET_VAL(HTT_T2H_MONITOR_MAC_HEADER_NUM_MPDU, value);   \
        (word) |= (value)  << HTT_T2H_MONITOR_MAC_HEADER_NUM_MPDU_S;     \
    } while (0)
#define HTT_T2H_MONITOR_MAC_HEADER_NUM_MPDU_GET(word) \
    (((word) & HTT_T2H_MONITOR_MAC_HEADER_NUM_MPDU_M) >> \
    HTT_T2H_MONITOR_MAC_HEADER_NUM_MPDU_S)

/**
 * @brief target -> host flow pool resize Message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_FLOW_POOL_RESIZE
 *
 * @details
 *  HTT_T2H_MSG_TYPE_FLOW_POOL_RESIZE message is sent by the target when
 *  the flow pool associated with the specified ID is resized
 *
 *  The message would appear as follows:
 *
 *     |31                             16|15             8|7              0|
 *     |---------------------------------+----------------+----------------|
 *     |                      reserved0                   | Msg type       |
 *     |-------------------------------------------------------------------|
 *     |         flow pool new size      |           flow pool ID          |
 *     |-------------------------------------------------------------------|
 *
 *  The message is interpreted as follows:
 *  b'0:7   - msg_type: This will be set to 0x21
 *            (HTT_T2H_MSG_TYPE_FLOW_POOL_RESIZE)
 *
 *  b'0:15  - flow pool ID: Existing flow pool ID
 *
 *  b'16:31 - flow pool new size: new pool size for exisiting flow pool ID
 *
 */

PREPACK struct htt_flow_pool_resize_t {
    A_UINT32 msg_type:8,
             reserved0:24;
    A_UINT32 flow_pool_id:16,
             flow_pool_new_size:16;
} POSTPACK;

#define HTT_FLOW_POOL_RESIZE_SZ  (sizeof(struct htt_flow_pool_resize_t))

#define HTT_FLOW_POOL_RESIZE_FLOW_POOL_ID_M      0x0000ffff
#define HTT_FLOW_POOL_RESIZE_FLOW_POOL_ID_S      0

#define HTT_FLOW_POOL_RESIZE_FLOW_POOL_NEW_SIZE_M    0xffff0000
#define HTT_FLOW_POOL_RESIZE_FLOW_POOL_NEW_SIZE_S    16


#define HTT_FLOW_POOL_RESIZE_FLOW_POOL_ID_GET(_var)    \
    (((_var) & HTT_FLOW_POOL_RESIZE_FLOW_POOL_ID_M) >> \
            HTT_FLOW_POOL_RESIZE_FLOW_POOL_ID_S)

#define HTT_FLOW_POOL_RESIZE_FLOW_POOL_ID_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_RESIZE_FLOW_POOL_ID, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_RESIZE_FLOW_POOL_ID_S)); \
    } while (0)


#define HTT_FLOW_POOL_RESIZE_FLOW_POOL_NEW_SIZE_GET(_var)    \
        (((_var) & HTT_FLOW_POOL_RESIZE_FLOW_POOL_NEW_SIZE_M) >> \
                HTT_FLOW_POOL_RESIZE_FLOW_POOL_NEW_SIZE_S)

#define HTT_FLOW_POOL_RESIZE_FLOW_POOL_NEW_SIZE_SET(_var, _val)            \
    do {                                                            \
        HTT_CHECK_SET_VAL(HTT_FLOW_POOL_RESIZE_FLOW_POOL_NEW_SIZE, _val);  \
        ((_var) |= ((_val) << HTT_FLOW_POOL_RESIZE_FLOW_POOL_NEW_SIZE_S)); \
    } while (0)



#define HTT_CFR_CAPTURE_MAGIC_PATTERN                0xCCCCCCCC
#define HTT_CFR_CAPTURE_READ_INDEX_OFFSET            0 /* bytes */
#define HTT_CFR_CAPTURE_SIZEOF_READ_INDEX_BYTES      4
#define HTT_CFR_CAPTURE_WRITE_INDEX_OFFSET /* bytes */ \
   (HTT_CFR_CAPTURE_READ_INDEX_OFFSET + HTT_CFR_CAPTURE_SIZEOF_READ_INDEX_BYTES)
#define HTT_CFR_CAPTURE_SIZEOF_WRITE_INDEX_BYTES     4
#define HTT_CFR_CAPTURE_SIZEOF_MAGIC_PATTERN_BYTES   4
/*
 * The read and write indices point to the data within the host buffer.
 * Because the first 4 bytes of the host buffer is used for the read index and
 * the next 4 bytes for the write index, the data itself starts at offset 8.
 * The read index and write index are the byte offsets from the base of the
 * meta-data buffer, and thus have a minimum value of 8 rather than 0.
 * Refer the ASCII text picture below.
 */
#define HTT_CFR_CAPTURE_INITIAL_RW_START_INDEX       \
   (HTT_CFR_CAPTURE_SIZEOF_READ_INDEX_BYTES +        \
    HTT_CFR_CAPTURE_SIZEOF_WRITE_INDEX_BYTES)

/*
 ***************************************************************************
 *
 * Layout when CFR capture message type is 'HTT_PEER_CFR_CAPTURE_MSG_TYPE_1'
 *
 ***************************************************************************
 *
 * The memory allocated by WMI_CHANNEL_CAPTURE_HOST_MEM_REQ_ID is used
 * in the below format. The HTT message 'htt_cfr_dump_compl_ind' is sent by
 * FW to Host whenever a CFR capture (CFR data1 or CFR data2 etc.,) is
 * written into the Host memory region mentioned below.
 *
 * Read index is updated by the Host. At any point of time, the read index will
 * indicate the index that will next be read by the Host. The read index is
 * in units of bytes offset from the base of the meta-data buffer.
 *
 * Write index is updated by the FW. At any point of time, the write index will
 * indicate from where the FW can start writing any new data. The write index is
 * in units of bytes offset from the base of the meta-data buffer.
 *
 * If the Host is not fast enough in reading the CFR data, any new capture data
 * would be dropped if there is no space left to write the new captures.
 *
 * The last 4 bytes of the memory region will have the magic pattern
 * HTT_CFR_CAPTURE_MAGIC_PATTERN. This can be used to ensure that the FW does
 * not overrun the host buffer.
 *
 *       ,--------------------.           read and write indices store the
 *       |                    |           byte offset from the base of the
 *       |           ,--------+--------.  meta-data buffer to the next
 *       |           |        |        |  location within the data buffer
 *       |           |        v        v  that will be read / written
 *   ************************************************************************
 *   *  Read     *   Write   *                                   *  Magic   *
 *   *  index    *   index   * CFR data1 ......  CFR data N      * pattern  *
 *   * (4 bytes) * (4 bytes) *                                   * (4 bytes)*
 *   ************************************************************************
 *                           |<---------- data buffer ---------->|
 *
 *   |<----------------- meta-data buffer allocated in Host ----------------|
 *
 * Note:
 *   - Considering the 4 bytes needed to store the Read index (R) and the
 *     Write index (W), the initial value is as follows:
 *     R = W = HTT_CFR_CAPTURE_INITIAL_RW_START_INDEX
 *   - Buffer empty condition:
 *     R = W
 *
 * Regarding CFR data format:
 * --------------------------
 *
 * Each CFR tone is stored in HW as 16-bits with the following format:
 * {bits[15:12], bits[11:6], bits[5:0]} =
 *                         {unsigned exponent (4 bits),
 *                         signed mantissa_real (6 bits),
 *                         signed mantissa_imag (6 bits)}
 *
 * CFR_real = mantissa_real * 2^(exponent-5)
 * CFR_imag = mantissa_imag * 2^(exponent-5)
 *
 *
 * The CFR data is written to the 16-bit unsigned output array (buff) in
 * ascending tone order. For example, the Legacy20 CFR is output as follows:
 *
 *        buff[0]: [CFR_exp[-26], CFR_mant_real[-26], CFR_mant_imag[-26]]
 *        buff[1]: [CFR_exp[-25], CFR_mant_real[-25], CFR_mant_imag[-25]]
 *                            .
 *                            .
 *                            .
 *        buff[N-2]: [CFR_exp[25], CFR_mant_real[25], CFR_mant_imag[25]]
 *        buff[N-1]: [CFR_exp[26], CFR_mant_real[26], CFR_mant_imag[26]]
 */

/* Bandwidth of peer CFR captures */
typedef enum {
    HTT_PEER_CFR_CAPTURE_BW_20MHZ    = 0,
    HTT_PEER_CFR_CAPTURE_BW_40MHZ    = 1,
    HTT_PEER_CFR_CAPTURE_BW_80MHZ    = 2,
    HTT_PEER_CFR_CAPTURE_BW_160MHZ   = 3,
    HTT_PEER_CFR_CAPTURE_BW_80_80MHZ = 4,
    HTT_PEER_CFR_CAPTURE_BW_MAX,
} HTT_PEER_CFR_CAPTURE_BW;

/* Mode of the peer CFR captures. The type of RX frame for which the CFR
 * was captured
 */
typedef enum {
    HTT_PEER_CFR_CAPTURE_MODE_LEGACY     = 0,
    HTT_PEER_CFR_CAPTURE_MODE_DUP_LEGACY = 1,
    HTT_PEER_CFR_CAPTURE_MODE_HT         = 2,
    HTT_PEER_CFR_CAPTURE_MODE_VHT        = 3,
    HTT_PEER_CFR_CAPTURE_MODE_MAX,
} HTT_PEER_CFR_CAPTURE_MODE;

typedef enum {
    /* This message type is currently used for the below purpose:
     *
     * - capture_method = WMI_PEER_CFR_CAPTURE_METHOD_NULL_FRAME in the
     *   wmi_peer_cfr_capture_cmd.
     *   If payload_present bit is set to 0 then the associated memory region
     *   gets allocated through WMI_CHANNEL_CAPTURE_HOST_MEM_REQ_ID.
     *   If payload_present bit is set to 1 then CFR dump is part of the HTT
     *   message; the CFR dump will be present at the end of the message,
     *   after the chan_phy_mode.
     */
    HTT_PEER_CFR_CAPTURE_MSG_TYPE_1  = 0x1,

    /* Always keep this last */
    HTT_PEER_CFR_CAPTURE_MSG_TYPE_MAX,
} HTT_PEER_CFR_CAPTURE_MSG_TYPE;

/**
 * @brief target -> host CFR dump completion indication message definition
 * htt_cfr_dump_compl_ind when the version is HTT_PEER_CFR_CAPTURE_MSG_TYPE_1.
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_CFR_DUMP_COMPL_IND
 *
 * @details
 * The following diagram shows the format of the Channel Frequency Response
 * (CFR) dump completion indication. This inidcation is sent to the Host when
 * the channel capture of a peer is copied by Firmware into the Host memory
 *
 * **************************************************************************
 *
 *   Message format when the CFR capture message type is
 *   'HTT_PEER_CFR_CAPTURE_MSG_TYPE_1'
 *
 * **************************************************************************
 *
 *          |31                           16|15                 |8|7        0|
 *          |----------------------------------------------------------------|
 * header:  |                           reserved                |P| msg_type |
 * word 0   |                                                   | |          |
 *          |----------------------------------------------------------------|
 * payload: |                      cfr_capture_msg_type                      |
 * word 1   |                                                                |
 *          |----------------------------------------------------------------|
 *          | vdev_id | captype |   chbw   | sts | mode | capbw |S| req_id   |
 * word 2   |         |         |          |     |      |       | |          |
 *          |----------------------------------------------------------------|
 *          |                          mac_addr31to0                         |
 * word 3   |                                                                |
 *          |----------------------------------------------------------------|
 *          |      unused / reserved        |       mac_addr47to32           |
 * word 4   |                               |                                |
 *          |----------------------------------------------------------------|
 *          |                             index                              |
 * word 5   |                                                                |
 *          |----------------------------------------------------------------|
 *          |                             length                             |
 * word 6   |                                                                |
 *          |----------------------------------------------------------------|
 *          |                           timestamp                            |
 * word 7   |                                                                |
 *          |----------------------------------------------------------------|
 *          |                            counter                             |
 * word 8   |                                                                |
 *          |----------------------------------------------------------------|
 *          |                            chan_mhz                            |
 * word 9   |                                                                |
 *          |----------------------------------------------------------------|
 *          |                        band_center_freq1                       |
 * word 10  |                                                                |
 *          |----------------------------------------------------------------|
 *          |                        band_center_freq2                       |
 * word 11  |                                                                |
 *          |----------------------------------------------------------------|
 *          |                          chan_phy_mode                         |
 * word 12  |                                                                |
 *          |----------------------------------------------------------------|
 * where,
 * P       - payload present bit (payload_present explained below)
 * req_id  - memory request id (mem_req_id explained below)
 * S       - status field (status explained below)
 * capbw   - capture bandwidth (capture_bw explained below)
 * mode    - mode of capture (mode explained below)
 * sts     - space time streams (sts_count explained below)
 * chbw    - channel bandwidth (channel_bw explained below)
 * captype - capture type (cap_type explained below)
 *
 * The following field definitions describe the format of the CFR dump
 * completion indication sent from the target to the host
 *
 * Header fields:
 *
 * Word 0
 * - msg_type
 *   Bits 7:0
 *   Purpose: Identifies this as CFR TX completion indication
 *   Value: 0x22 (HTT_T2H_MSG_TYPE_CFR_DUMP_COMPL_IND)
 * - payload_present
 *   Bit 8
 *   Purpose: Identifies how CFR data is sent to host
 *   Value: 0 - If CFR Payload is written to host memory
 *          1 - If CFR Payload is sent as part of HTT message
 *              (This is the requirement for SDIO/USB where it is
 *               not possible to write CFR data to host memory)
 * - reserved
 *   Bits 31:9
 *   Purpose: Reserved
 *   Value: 0
 *
 * Payload fields:
 *
 * Word 1
 * - cfr_capture_msg_type
 *   Bits 31:0
 *   Purpose: Contains the type of the message HTT_PEER_CFR_CAPTURE_MSG_TYPE
 *       to specify the format used for the remainder of the message
 *   Value: HTT_PEER_CFR_CAPTURE_MSG_TYPE_1
 *          (currently only MSG_TYPE_1 is defined)
 *
 * Word 2
 * - mem_req_id
 *   Bits 6:0
 *   Purpose: Contain the mem request id of the region where the CFR capture
 *       has been stored - of type WMI_HOST_MEM_REQ_ID
 *   Value: WMI_CHANNEL_CAPTURE_HOST_MEM_REQ_ID (if payload_present is 1,
            this value is invalid)
 * - status
 *   Bit 7
 *   Purpose: Boolean value carrying the status of the CFR capture of the peer
 *   Value: 1 (True) - Successful; 0 (False) - Not successful
 * - capture_bw
 *   Bits 10:8
 *   Purpose: Carry the bandwidth of the CFR capture
 *   Value: Bandwidth of the CFR capture of type HTT_PEER_CFR_CAPTURE_BW
 * - mode
 *   Bits 13:11
 *   Purpose: Carry the mode of the rx frame for which the CFR was captured
 *   Value: Mode of the CFR capture of type HTT_PEER_CFR_CAPTURE_MODE
 * - sts_count
 *   Bits 16:14
 *   Purpose: Carry the number of space time streams
 *   Value: Number of space time streams
 * - channel_bw
 *   Bits 19:17
 *   Purpose: Carry the bandwidth of the channel of the vdev performing the
 *       measurement
 *   Value: Bandwidth of the channel (of type HTT_PEER_CFR_CAPTURE_BW)
 * - cap_type
 *   Bits 23:20
 *   Purpose: Carry the type of the capture
 *   Value: Capture type (of type WMI_PEER_CFR_CAPTURE_METHOD)
 * - vdev_id
 *   Bits 31:24
 *   Purpose: Carry the virtual device id
 *   Value: vdev ID
 *
 * Word 3
 * - mac_addr31to0
 *   Bits 31:0
 *   Purpose: Contain the bits 31:0 of the peer MAC address
 *   Value: Bits 31:0 of the peer MAC address
 *
 * Word 4
 * - mac_addr47to32
 *   Bits 15:0
 *   Purpose: Contain the bits 47:32 of the peer MAC address
 *   Value: Bits 47:32 of the peer MAC address
 *
 * Word 5
 * - index
 *   Bits 31:0
 *   Purpose: Contain the index at which this CFR dump was written in the Host
 *   allocated memory. This index is the number of bytes from the base address.
 *   Value: Index position
 *
 * Word 6
 * - length
 *   Bits 31:0
 *   Purpose: Carry the length of the CFR capture of the peer, in bytes
 *   Value: Length of the CFR capture of the peer
 *
 * Word 7
 * - timestamp
 *   Bits 31:0
 *   Purpose: Carry the time at which the CFR was captured in the hardware. The
 *   clock used for this timestamp is private to the target and not visible to
 *   the host i.e., Host can interpret only the relative timestamp deltas from
 *   one message to the next, but can't interpret the absolute timestamp from a
 *   single message.
 *   Value: Timestamp in microseconds
 *
 * Word 8
 * - counter
 *   Bits 31:0
 *   Purpose: Carry the count of the current CFR capture from FW. This is
 *   helpful to identify any drops in FW in any scenario (e.g., lack of space
 *   in host memory)
 *   Value: Count of the current CFR capture
 *
 * Word 9
 * - chan_mhz
 *   Bits 31:0
 *   Purpose: Carry the primary 20 MHz channel frequency in MHz of the VDEV
 *   Value: Primary 20 channel frequency
 *
 * Word 10
 * - band_center_freq1
 *   Bits 31:0
 *   Purpose: Carry the center frequency 1 in MHz of the VDEV
 *   Value: Center frequency 1 in MHz
 *
 * Word 11
 * - band_center_freq2
 *   Bits 31:0
 *   Purpose: Carry the center frequency 2 in MHz. valid only for 11acvht of
 *   the VDEV
 *   80plus80 mode
 *   Value: Center frequency 2 in MHz
 *
 * Word 12
 * - chan_phy_mode
 *   Bits 31:0
 *   Purpose: Carry the phy mode of the channel, of the VDEV
 *   Value: WLAN_PHY_MODE of the channel defined in wlan_defs.h
 */
PREPACK struct htt_cfr_dump_ind_type_1 {
    A_UINT32 mem_req_id:7,
             status:1,
             capture_bw:3,
             mode:3,
             sts_count:3,
             channel_bw:3,
             cap_type:4,
             vdev_id:8;
    htt_mac_addr addr;
    A_UINT32 index;
    A_UINT32 length;
    A_UINT32 timestamp;
    A_UINT32 counter;
    struct htt_chan_change_msg chan;
} POSTPACK;

PREPACK struct htt_cfr_dump_compl_ind {
    A_UINT32 msg_type; /* HTT_PEER_CFR_CAPTURE_MSG_TYPE */
    union {
        /* Message format when msg_type = HTT_PEER_CFR_CAPTURE_MSG_TYPE_1 */
        struct htt_cfr_dump_ind_type_1 htt_cfr_dump_compl_ind_type_1;
        /* If there is a need to change the memory layout and its associated
         * HTT indication format, a new CFR capture message type can be
         * introduced and added into this union.
         */
    };
} POSTPACK;

/*
 * Get / set macros for the bit fields within WORD-1 of htt_cfr_dump_compl_ind,
 * msg_type = HTT_PEER_CFR_CAPTURE_MSG_TYPE_1
 */
#define HTT_T2H_CFR_DUMP_PAYLOAD_PRESENT_ID_M      0x00000100
#define HTT_T2H_CFR_DUMP_PAYLOAD_PRESENT_ID_S      8

#define HTT_T2H_CFR_DUMP_PAYLOAD_PRESENT_ID_SET(word, value) \
  do { \
         HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_PAYLOAD_PRESENT_ID, value); \
         (word)  |= (value) << HTT_T2H_CFR_DUMP_PAYLOAD_PRESENT_ID_S;   \
     } while(0)
#define HTT_T2H_CFR_DUMP_PAYLOAD_PRESENT_ID_GET(word) \
       (((word) & HTT_T2H_CFR_DUMP_PAYLOAD_PRESENT_ID_M) >> \
           HTT_T2H_CFR_DUMP_PAYLOAD_PRESENT_ID_S)

/*
 * Get / set macros for the bit fields within WORD-2 of htt_cfr_dump_compl_ind,
 * msg_type = HTT_PEER_CFR_CAPTURE_MSG_TYPE_1
 */
#define HTT_T2H_CFR_DUMP_TYPE1_MEM_REQ_ID_M        0X0000007F
#define HTT_T2H_CFR_DUMP_TYPE1_MEM_REQ_ID_S        0
#define HTT_T2H_CFR_DUMP_TYPE1_STATUS_M            0X00000080
#define HTT_T2H_CFR_DUMP_TYPE1_STATUS_S            7
#define HTT_T2H_CFR_DUMP_TYPE1_CAP_BW_M            0X00000700
#define HTT_T2H_CFR_DUMP_TYPE1_CAP_BW_S            8
#define HTT_T2H_CFR_DUMP_TYPE1_MODE_M              0X00003800
#define HTT_T2H_CFR_DUMP_TYPE1_MODE_S              11
#define HTT_T2H_CFR_DUMP_TYPE1_STS_M               0X0001C000
#define HTT_T2H_CFR_DUMP_TYPE1_STS_S               14
#define HTT_T2H_CFR_DUMP_TYPE1_CHAN_BW_M           0X000E0000
#define HTT_T2H_CFR_DUMP_TYPE1_CHAN_BW_S           17
#define HTT_T2H_CFR_DUMP_TYPE1_CAP_TYPE_M          0X00F00000
#define HTT_T2H_CFR_DUMP_TYPE1_CAP_TYPE_S          20
#define HTT_T2H_CFR_DUMP_TYPE1_VDEV_ID_M           0XFF000000
#define HTT_T2H_CFR_DUMP_TYPE1_VDEV_ID_S           24

#define HTT_T2H_CFR_DUMP_TYPE1_MEM_REQ_ID_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_TYPE1_MEM_REQ_ID, value); \
          (word) |= (value)  << HTT_T2H_CFR_DUMP_TYPE1_MEM_REQ_ID_S; \
      } while (0)
#define HTT_T2H_CFR_DUMP_TYPE1_MEM_REQ_ID_GET(word) \
       (((word) & HTT_T2H_CFR_DUMP_TYPE1_MEM_REQ_ID_M) >> \
           HTT_T2H_CFR_DUMP_TYPE1_MEM_REQ_ID_S)

#define HTT_T2H_CFR_DUMP_TYPE1_STATUS_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_TYPE1_STATUS, value); \
          (word) |= (value)  << HTT_T2H_CFR_DUMP_TYPE1_STATUS_S; \
      } while (0)
#define HTT_T2H_CFR_DUMP_TYPE1_STATUS_GET(word) \
      (((word) & HTT_T2H_CFR_DUMP_TYPE1_STATUS_M) >> \
          HTT_T2H_CFR_DUMP_TYPE1_STATUS_S)

#define HTT_T2H_CFR_DUMP_TYPE1_CAP_BW_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_TYPE1_CAP_BW, value); \
          (word) |= (value)  << HTT_T2H_CFR_DUMP_TYPE1_CAP_BW_S; \
      } while (0)
#define HTT_T2H_CFR_DUMP_TYPE1_CAP_BW_GET(word) \
        (((word) & HTT_T2H_CFR_DUMP_TYPE1_CAP_BW_M) >> \
           HTT_T2H_CFR_DUMP_TYPE1_CAP_BW_S)

#define HTT_T2H_CFR_DUMP_TYPE1_MODE_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_TYPE1_MODE, value); \
          (word) |= (value)  << HTT_T2H_CFR_DUMP_TYPE1_MODE_S; \
      } while (0)
#define HTT_T2H_CFR_DUMP_TYPE1_MODE_GET(word) \
        (((word) & HTT_T2H_CFR_DUMP_TYPE1_MODE_M) >> \
            HTT_T2H_CFR_DUMP_TYPE1_MODE_S)

#define HTT_T2H_CFR_DUMP_TYPE1_STS_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_TYPE1_STS, value); \
          (word) |= (value)  << HTT_T2H_CFR_DUMP_TYPE1_STS_S; \
      } while (0)
#define HTT_T2H_CFR_DUMP_TYPE1_STS_GET(word) \
        (((word) & HTT_T2H_CFR_DUMP_TYPE1_STS_M) >> \
            HTT_T2H_CFR_DUMP_TYPE1_STS_S)

#define HTT_T2H_CFR_DUMP_TYPE1_CHAN_BW_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_TYPE1_CHAN_BW, value); \
          (word) |= (value)  << HTT_T2H_CFR_DUMP_TYPE1_CHAN_BW_S; \
      } while (0)
#define HTT_T2H_CFR_DUMP_TYPE1_CHAN_BW_GET(word) \
        (((word) & HTT_T2H_CFR_DUMP_TYPE1_CHAN_BW_M) >> \
            HTT_T2H_CFR_DUMP_TYPE1_CHAN_BW_S)

#define HTT_T2H_CFR_DUMP_TYPE1_CAP_TYPE_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_TYPE1_CAP_TYPE, value); \
          (word) |= (value)  << HTT_T2H_CFR_DUMP_TYPE1_CAP_TYPE_S; \
      } while (0)
#define HTT_T2H_CFR_DUMP_TYPE1_CAP_TYPE_GET(word) \
        (((word) & HTT_T2H_CFR_DUMP_TYPE1_CAP_TYPE_M) >> \
            HTT_T2H_CFR_DUMP_TYPE1_CAP_TYPE_S)

#define HTT_T2H_CFR_DUMP_TYPE1_VDEV_ID_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_CFR_DUMP_TYPE1_VDEV_ID, value); \
          (word) |= (value)  << HTT_T2H_CFR_DUMP_TYPE1_VDEV_ID_S; \
      } while (0)
#define HTT_T2H_CFR_DUMP_TYPE1_VDEV_ID_GET(word) \
        (((word) & HTT_T2H_CFR_DUMP_TYPE1_VDEV_ID_M) >> \
            HTT_T2H_CFR_DUMP_TYPE1_VDEV_ID_S)


/**
 * @brief target -> host peer (PPDU) stats message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_PEER_STATS_IND
 *
 * @details
 * This message is generated by FW when FW is sending stats to  host
 * about one or more PPDUs that the FW has transmitted to one or more peers.
 * This message is sent autonomously by the target rather than upon request
 * by the host.
 * The following field definitions describe the format of the HTT target
 * to host peer stats indication message.
 *
 * The HTT_T2H PPDU_STATS_IND message has a header followed by one
 * or more PPDU stats records.
 * Each PPDU stats record uses a htt_tx_ppdu_stats_info TLV.
 * If the details of N PPDUS are sent in one PEER_STATS_IND message,
 * then the message would start with the
 * header, followed by N htt_tx_ppdu_stats_info structures, as depicted
 * below.
 *
 *       |31                            16|15|14|13 11|10 9|8|7       0|
 *       |-------------------------------------------------------------|
 *       |                        reserved                   |MSG_TYPE |
 *       |-------------------------------------------------------------|
 * rec 0 |                             TLV header                      |
 * rec 0 |-------------------------------------------------------------|
 * rec 0 |                      ppdu successful bytes                  |
 * rec 0 |-------------------------------------------------------------|
 * rec 0 |                        ppdu retry bytes                     |
 * rec 0 |-------------------------------------------------------------|
 * rec 0 |                        ppdu failed bytes                    |
 * rec 0 |-------------------------------------------------------------|
 * rec 0 |              peer id           | S|SG|  BW | BA |A|rate code|
 * rec 0 |-------------------------------------------------------------|
 * rec 0 |        retried MSDUs           |       successful MSDUs     |
 * rec 0 |-------------------------------------------------------------|
 * rec 0 |         TX duration            |         failed MSDUs       |
 * rec 0 |-------------------------------------------------------------|
 *                                       ...
 *       |-------------------------------------------------------------|
 * rec N |                             TLV header                      |
 * rec N |-------------------------------------------------------------|
 * rec N |                      ppdu successful bytes                  |
 * rec N |-------------------------------------------------------------|
 * rec N |                        ppdu retry bytes                     |
 * rec N |-------------------------------------------------------------|
 * rec N |                        ppdu failed bytes                    |
 * rec N |-------------------------------------------------------------|
 * rec N |              peer id           | S|SG|  BW | BA |A|rate code|
 * rec N |-------------------------------------------------------------|
 * rec N |        retried MSDUs           |       successful MSDUs     |
 * rec N |-------------------------------------------------------------|
 * rec N |         TX duration            |         failed MSDUs       |
 * rec N |-------------------------------------------------------------|
 *
 * where:
 *     A  = is A-MPDU flag
 *     BA = block-ack failure flags
 *     BW = bandwidth spec
 *     SG = SGI enabled spec
 *     S  = skipped rate ctrl
 * One htt_tx_ppdu_stats_info instance will have stats for one PPDU
 *
 * Header
 * ------
 * dword0 - b'0:7  - msg_type : 0x23 (HTT_T2H_MSG_TYPE_PEER_STATS_IND)
 * dword0 - b'8:31 - reserved : Reserved for future use
 *
 * payload include below peer_stats information
 * --------------------------------------------
 * @TLV : HTT_PPDU_STATS_INFO_TLV
 * @tx_success_bytes : total successful bytes in the PPDU.
 * @tx_retry_bytes   : total retried bytes in the PPDU.
 * @tx_failed_bytes  : total failed bytes in the PPDU.
 * @tx_ratecode      : rate code used for the PPDU.
 * @is_ampdu         : Indicates PPDU is AMPDU or not.
 * @ba_ack_failed    : BA/ACK failed for this PPDU
 *                     b00 -> BA received
 *                     b01 -> BA failed once
 *                     b10 -> BA failed twice, when HW retry is enabled.
 * @bw               : BW
 *                     b00 -> 20 MHz
 *                     b01 -> 40 MHz
 *                     b10 -> 80 MHz
 *                     b11 -> 160 MHz (or 80+80)
 * @sg               : SGI enabled
 * @s                : skipped ratectrl
 * @peer_id          : peer id
 * @tx_success_msdus : successful MSDUs
 * @tx_retry_msdus   : retried MSDUs
 * @tx_failed_msdus  : MSDUs dropped in FW after max retry
 * @tx_duration      : Tx duration for the PPDU (microsecond units)
 */


/**
 * @brief target -> host backpressure event
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_BKPRESSURE_EVENT_IND
 *
 * @details
 *  HTT_T2H_MSG_TYPE_BKPRESSURE_EVENTID message is sent by the target when
 *  continuous backpressure is seen in the LMAC/ UMAC rings software rings.
 *  This message will only be sent if the backpressure condition has existed
 *  continuously for an initial period (100 ms).
 *  Repeat messages with updated information will be sent after each
 *  subsequent period (100 ms) as long as the backpressure remains unabated.
 *  This message indicates the ring id along with current head and tail index
 *  locations (i.e. write and read indices).
 *  The backpressure time indicates the time in ms for which continous
 *  backpressure has been observed in the ring.
 *
 *  The message format is as follows:
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |    ring_id     |   ring_type    |     pdev_id    |     msg_type   |
 *     |-------------------------------------------------------------------|
 *     |             tail_idx            |             head_idx            |
 *     |-------------------------------------------------------------------|
 *     |                      backpressure_time_ms                         |
 *     |-------------------------------------------------------------------|
 *
 *  The message is interpreted as follows:
 *  dword0 - b'0:7   - msg_type: This will be set to 0x24
 *                               (HTT_T2H_MSG_TYPE_BKPRESSURE_EVENT_IND)
 *           b'8:15  - pdev_id:  0 indicates msg is for UMAC ring.
 *                               1, 2, 3 indicates pdev_id 0,1,2 and
                                 the msg is for LMAC ring.
 *           b'16:23 - ring_type: Refer to enum htt_backpressure_ring_type.
 *           b'24:31 - ring_id:  Refer enum htt_backpressure_umac_ring_id/
 *                               htt_backpressure_lmac_ring_id. This represents
 *                               the ring id for which continous backpressure is seen
 *
 *  dword1 - b'0:15  - head_idx: This indicates the current head index of
 *                               the ring indicated by the ring_id
 *
 *  dword1 - b'16:31 - tail_idx: This indicates the current tail index of
 *                               the ring indicated by the ring id
 *
 *  dword2 - b'0:31  - backpressure_time_ms: Indicates how long continous
 *                               backpressure has been seen in the ring
 *                               indicated by the ring_id.
 *                               Units = milliseconds
 */
#define HTT_T2H_RX_BKPRESSURE_PDEV_ID_M   0x0000ff00
#define HTT_T2H_RX_BKPRESSURE_PDEV_ID_S   8
#define HTT_T2H_RX_BKPRESSURE_RING_TYPE_M 0x00ff0000
#define HTT_T2H_RX_BKPRESSURE_RING_TYPE_S 16
#define HTT_T2H_RX_BKPRESSURE_RINGID_M    0xff000000
#define HTT_T2H_RX_BKPRESSURE_RINGID_S    24
#define HTT_T2H_RX_BKPRESSURE_HEAD_IDX_M  0x0000ffff
#define HTT_T2H_RX_BKPRESSURE_HEAD_IDX_S  0
#define HTT_T2H_RX_BKPRESSURE_TAIL_IDX_M  0xffff0000
#define HTT_T2H_RX_BKPRESSURE_TAIL_IDX_S  16
#define HTT_T2H_RX_BKPRESSURE_TIME_MS_M   0xffffffff
#define HTT_T2H_RX_BKPRESSURE_TIME_MS_S   0

#define HTT_T2H_RX_BKPRESSURE_PDEV_ID_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_RX_BKPRESSURE_PDEV_ID, value); \
          (word) |= (value)  << HTT_T2H_RX_BKPRESSURE_PDEV_ID_S; \
      } while (0)
#define HTT_T2H_RX_BKPRESSURE_PDEV_ID_GET(word) \
        (((word) & HTT_T2H_RX_BKPRESSURE_PDEV_ID_M) >> \
            HTT_T2H_RX_BKPRESSURE_PDEV_ID_S)

#define HTT_T2H_RX_BKPRESSURE_RING_TYPE_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_RX_BKPRESSURE_RING_TYPE, value); \
          (word) |= (value)  << HTT_T2H_RX_BKPRESSURE_RING_TYPE_S; \
      } while (0)
#define HTT_T2H_RX_BKPRESSURE_RING_TYPE_GET(word) \
        (((word) & HTT_T2H_RX_BKPRESSURE_RING_TYPE_M) >> \
            HTT_T2H_RX_BKPRESSURE_RING_TYPE_S)

#define HTT_T2H_RX_BKPRESSURE_RINGID_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_RX_BKPRESSURE_RINGID, value); \
          (word) |= (value)  << HTT_T2H_RX_BKPRESSURE_RINGID_S; \
      } while (0)
#define HTT_T2H_RX_BKPRESSURE_RINGID_GET(word) \
        (((word) & HTT_T2H_RX_BKPRESSURE_RINGID_M) >> \
            HTT_T2H_RX_BKPRESSURE_RINGID_S)

#define HTT_T2H_RX_BKPRESSURE_HEAD_IDX_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_RX_BKPRESSURE_HEAD_IDX, value); \
          (word) |= (value)  << HTT_T2H_RX_BKPRESSURE_HEAD_IDX_S; \
      } while (0)
#define HTT_T2H_RX_BKPRESSURE_HEAD_IDX_GET(word) \
        (((word) & HTT_T2H_RX_BKPRESSURE_HEAD_IDX_M) >> \
            HTT_T2H_RX_BKPRESSURE_HEAD_IDX_S)

#define HTT_T2H_RX_BKPRESSURE_TAIL_IDX_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_RX_BKPRESSURE_TAIL_IDX, value); \
          (word) |= (value)  << HTT_T2H_RX_BKPRESSURE_TAIL_IDX_S; \
      } while (0)
#define HTT_T2H_RX_BKPRESSURE_TAIL_IDX_GET(word) \
        (((word) & HTT_T2H_RX_BKPRESSURE_TAIL_IDX_M) >> \
            HTT_T2H_RX_BKPRESSURE_TAIL_IDX_S)

#define HTT_T2H_RX_BKPRESSURE_TIME_MS_SET(word, value) \
   do { \
          HTT_CHECK_SET_VAL(HTT_T2H_RX_BKPRESSURE_TIME_MS, value); \
          (word) |= (value)  << HTT_T2H_RX_BKPRESSURE_TIME_MS_S; \
      } while (0)
#define HTT_T2H_RX_BKPRESSURE_TIME_MS_GET(word) \
        (((word) & HTT_T2H_RX_BKPRESSURE_TIME_MS_M) >> \
            HTT_T2H_RX_BKPRESSURE_TIME_MS_S)

enum htt_backpressure_ring_type {
     HTT_SW_RING_TYPE_UMAC,
     HTT_SW_RING_TYPE_LMAC,
     HTT_SW_RING_TYPE_MAX,
};

/* Ring id for which the message is sent to host */
enum htt_backpressure_umac_ringid {
    HTT_SW_RING_IDX_REO_REO2SW1_RING,
    HTT_SW_RING_IDX_REO_REO2SW2_RING,
    HTT_SW_RING_IDX_REO_REO2SW3_RING,
    HTT_SW_RING_IDX_REO_REO2SW4_RING,
    HTT_SW_RING_IDX_REO_WBM2REO_LINK_RING,
    HTT_SW_RING_IDX_REO_REO2TCL_RING,
    HTT_SW_RING_IDX_REO_REO2FW_RING,
    HTT_SW_RING_IDX_REO_REO_RELEASE_RING,
    HTT_SW_RING_IDX_WBM_PPE_RELEASE_RING,
    HTT_SW_RING_IDX_TCL_TCL2TQM_RING,
    HTT_SW_RING_IDX_WBM_TQM_RELEASE_RING,
    HTT_SW_RING_IDX_WBM_REO_RELEASE_RING,
    HTT_SW_RING_IDX_WBM_WBM2SW0_RELEASE_RING,
    HTT_SW_RING_IDX_WBM_WBM2SW1_RELEASE_RING,
    HTT_SW_RING_IDX_WBM_WBM2SW2_RELEASE_RING,
    HTT_SW_RING_IDX_WBM_WBM2SW3_RELEASE_RING,
    HTT_SW_RING_IDX_REO_REO_CMD_RING,
    HTT_SW_RING_IDX_REO_REO_STATUS_RING,
    HTT_SW_UMAC_RING_IDX_MAX,
};

enum htt_backpressure_lmac_ringid {
    HTT_SW_RING_IDX_FW2RXDMA_BUF_RING,
    HTT_SW_RING_IDX_FW2RXDMA_STATUS_RING,
    HTT_SW_RING_IDX_FW2RXDMA_LINK_RING,
    HTT_SW_RING_IDX_SW2RXDMA_BUF_RING,
    HTT_SW_RING_IDX_WBM2RXDMA_LINK_RING,
    HTT_SW_RING_IDX_RXDMA2FW_RING,
    HTT_SW_RING_IDX_RXDMA2SW_RING,
    HTT_SW_RING_IDX_RXDMA2RELEASE_RING,
    HTT_SW_RING_IDX_RXDMA2REO_RING,
    HTT_SW_RING_IDX_MONITOR_STATUS_RING,
    HTT_SW_RING_IDX_MONITOR_BUF_RING,
    HTT_SW_RING_IDX_MONITOR_DESC_RING,
    HTT_SW_RING_IDX_MONITOR_DEST_RING,
    HTT_SW_LMAC_RING_IDX_MAX,
};

PREPACK struct htt_t2h_msg_bkpressure_event_ind_t {
     A_UINT32 msg_type:  8, /* HTT_T2H_MSG_TYPE_BKPRESSURE_EVENT_IND */
              pdev_id:   8,
              ring_type: 8, /* htt_backpressure_ring_type */
              /*
               * ring_id holds an enum value from either
               * htt_backpressure_umac_ringid or
               * htt_backpressure_lmac_ringid, based on
               * the ring_type setting.
               */
              ring_id:   8;
     A_UINT16 head_idx;
     A_UINT16 tail_idx;
     A_UINT32 backpressure_time_ms; /* Time in milliseconds for which backpressure is seen continuously */
} POSTPACK;


/*
 * Defines two 32 bit words that can be used by the target to indicate a per
 * user RU allocation and rate information.
 *
 * This information is currently provided in the "sw_response_reference_ptr"
 * (word 0) and "sw_response_reference_ptr_ext" (word 1) fields of the
 * "rx_ppdu_end_user_stats" TLV.
 *
 * VALID:
 *     The consumer of these words must explicitly check the valid bit,
 *     and only attempt interpretation of any of the remaining fields if
 *     the valid bit is set to 1.
 *
 * VERSION:
 *   The consumer of these words must also explicitly check the version bit,
 *   and only use the V0 definition if the VERSION field is set to 0.
 *
 * Version 1 is currently undefined, with the exception of the VALID and
 * VERSION fields.
 *
 * Version 0:
 *
 *   The fields below are duplicated per BW.
 *
 *   The consumer must determine which BW field to use, based on the UL OFDMA
 *   PPDU BW indicated by HW.
 *
 *     RU_START: RU26 start index for the user.
 *               Note that this is always using the RU26 index, regardless
 *               of the actual RU assigned to the user
 *               (i.e. the second RU52 is RU_START 2, RU_SIZE
 *               HTT_UL_OFDMA_V0_RU_SIZE_RU_52)
 *
 *     For example, 20MHz (the value in the top row is RU_START)
 *
 *       RU Size 0 (26):  |0|1|2|3|4|5|6|7|8|
 *       RU Size 1 (52):  |   |   | |   |   |
 *       RU Size 2 (106): |       | |       |
 *       RU Size 3 (242): |                 |
 *
 *     RU_SIZE: Indicates the RU size, as defined by enum
 *              htt_ul_ofdma_user_info_ru_size.
 *
 *     LDPC: LDPC enabled (if 0, BCC is used)
 *
 *     DCM: DCM enabled
 *
 *     |31 |   30|29 23|22     19|18   16|15           9| 8 |  7 |6  3|2 0|
 *     |---------------------------------+--------------------------------|
 *     |Ver|Valid|                   FW internal                          |
 *     |---------------------------------+--------------------------------|
 *     |   reserved    |Trig Type|RU SIZE|   RU START   |DCM|LDPC|MCS |NSS|
 *     |---------------------------------+--------------------------------|
 */

enum htt_ul_ofdma_user_info_ru_size {
    HTT_UL_OFDMA_V0_RU_SIZE_RU_26,
    HTT_UL_OFDMA_V0_RU_SIZE_RU_52,
    HTT_UL_OFDMA_V0_RU_SIZE_RU_106,
    HTT_UL_OFDMA_V0_RU_SIZE_RU_242,
    HTT_UL_OFDMA_V0_RU_SIZE_RU_484,
    HTT_UL_OFDMA_V0_RU_SIZE_RU_996,
    HTT_UL_OFDMA_V0_RU_SIZE_RU_996x2
};

/* htt_up_ofdma_user_info_v0 provides an abstract view of the info */
struct htt_ul_ofdma_user_info_v0 {
    A_UINT32 word0;
    A_UINT32 word1;
};

#define HTT_UL_OFDMA_USER_INFO_V0_BITMAP_W0 \
    A_UINT32 w0_fw_rsvd:30; \
    A_UINT32 w0_valid:1; \
    A_UINT32 w0_version:1;
struct htt_ul_ofdma_user_info_v0_bitmap_w0 {
    HTT_UL_OFDMA_USER_INFO_V0_BITMAP_W0
};

#define HTT_UL_OFDMA_USER_INFO_V0_BITMAP_W1 \
    A_UINT32 w1_nss:3; \
    A_UINT32 w1_mcs:4; \
    A_UINT32 w1_ldpc:1; \
    A_UINT32 w1_dcm:1; \
    A_UINT32 w1_ru_start:7; \
    A_UINT32 w1_ru_size:3; \
    A_UINT32 w1_trig_type:4; \
    A_UINT32 w1_unused:9;
struct htt_ul_ofdma_user_info_v0_bitmap_w1 {
    HTT_UL_OFDMA_USER_INFO_V0_BITMAP_W1
};

/* htt_up_ofdma_user_info_v0_bitmap shows what bitfields are within the info */
PREPACK struct htt_ul_ofdma_user_info_v0_bitmap {
    union {
        A_UINT32 word0;
        struct {
            HTT_UL_OFDMA_USER_INFO_V0_BITMAP_W0
        };
    };
    union {
        A_UINT32 word1;
        struct {
            HTT_UL_OFDMA_USER_INFO_V0_BITMAP_W1
        };
    };
} POSTPACK;

enum HTT_UL_OFDMA_TRIG_TYPE {
    HTT_UL_OFDMA_USER_INFO_V0_TRIG_TYPE_BASIC = 0,
    HTT_UL_OFDMA_USER_INFO_V0_TRIG_TYPE_BFRP,
    HTT_UL_OFDMA_USER_INFO_V0_TRIG_TYPE_MU_BAR,
    HTT_UL_OFDMA_USER_INFO_V0_TRIG_TYPE_MU_RTS_CTS,
    HTT_UL_OFDMA_USER_INFO_V0_TRIG_TYPE_BSR,
};


#define HTT_UL_OFDMA_USER_INFO_V0_SZ        (sizeof(struct htt_ul_ofdma_user_info_v0))

#define HTT_UL_OFDMA_USER_INFO_V0_W0_FW_INTERNAL_M  0x0000ffff
#define HTT_UL_OFDMA_USER_INFO_V0_W0_FW_INTERNAL_S  0

#define HTT_UL_OFDMA_USER_INFO_V0_W0_VALID_M 0x40000000
#define HTT_UL_OFDMA_USER_INFO_V0_W0_VALID_S 30

#define HTT_UL_OFDMA_USER_INFO_V0_W0_VER_M 0x80000000
#define HTT_UL_OFDMA_USER_INFO_V0_W0_VER_S 31

#define HTT_UL_OFDMA_USER_INFO_V0_W1_NSS_M       0x00000007
#define HTT_UL_OFDMA_USER_INFO_V0_W1_NSS_S       0

#define HTT_UL_OFDMA_USER_INFO_V0_W1_MCS_M       0x00000078
#define HTT_UL_OFDMA_USER_INFO_V0_W1_MCS_S       3

#define HTT_UL_OFDMA_USER_INFO_V0_W1_LDPC_M      0x00000080
#define HTT_UL_OFDMA_USER_INFO_V0_W1_LDPC_S      7

#define HTT_UL_OFDMA_USER_INFO_V0_W1_DCM_M       0x00000100
#define HTT_UL_OFDMA_USER_INFO_V0_W1_DCM_S       8

#define HTT_UL_OFDMA_USER_INFO_V0_W1_RU_START_M  0x0000fe00
#define HTT_UL_OFDMA_USER_INFO_V0_W1_RU_START_S  9

#define HTT_UL_OFDMA_USER_INFO_V0_W1_RU_SIZE_M   0x00070000
#define HTT_UL_OFDMA_USER_INFO_V0_W1_RU_SIZE_S   16

#define HTT_UL_OFDMA_USER_INFO_V0_W1_TRIG_TYP_M  0x00780000
#define HTT_UL_OFDMA_USER_INFO_V0_W1_TRIG_TYP_S  19

#define HTT_UL_OFDMA_USER_INFO_V0_W1_RESERVED1_M  0xff800000
#define HTT_UL_OFDMA_USER_INFO_V0_W1_RESERVED1_S  23

/*--- word 0 ---*/

#define HTT_UL_OFDMA_USER_INFO_V0_W0_FW_INTERNAL_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W0_FW_INTERNAL_M) >> HTT_UL_OFDMA_USER_INFO_V0_W0_FW_INTERNAL_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W0_FW_INTERNAL_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W0_FW_INTERNAL, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W0_FW_INTERNAL_S)); \
    } while (0)


#define HTT_UL_OFDMA_USER_INFO_V0_W0_VALID_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W0_VALID_M) >> HTT_UL_OFDMA_USER_INFO_V0_W0_VALID_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W0_VALID_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W0_VALID, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W0_VALID_S)); \
    } while (0)


#define HTT_UL_OFDMA_USER_INFO_V0_W0_VER_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W0_VER_M) >> HTT_UL_OFDMA_USER_INFO_V0_W0_VER_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W0_VER_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W0_VER, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W0_VER_S)); \
    } while (0)


/*--- word 1 ---*/

#define HTT_UL_OFDMA_USER_INFO_V0_W1_NSS_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W1_NSS_M) >> HTT_UL_OFDMA_USER_INFO_V0_W1_NSS_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W1_NSS_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W1_NSS, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W1_NSS_S)); \
    } while (0)


#define HTT_UL_OFDMA_USER_INFO_V0_W1_MCS_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W1_MCS_M) >> HTT_UL_OFDMA_USER_INFO_V0_W1_MCS_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W1_MCS_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W1_MCS, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W1_MCS_S)); \
    } while (0)


#define HTT_UL_OFDMA_USER_INFO_V0_W1_LDPC_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W1_LDPC_M) >> HTT_UL_OFDMA_USER_INFO_V0_W1_LDPC_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W1_LDPC_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W1_LDPC, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W1_LDPC_S)); \
    } while (0)


#define HTT_UL_OFDMA_USER_INFO_V0_W1_DCM_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W1_DCM_M) >> HTT_UL_OFDMA_USER_INFO_V0_W1_DCM_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W1_DCM_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W1_DCM, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W1_DCM_S)); \
    } while (0)


#define HTT_UL_OFDMA_USER_INFO_V0_W1_RU_START_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W1_RU_START_M) >> HTT_UL_OFDMA_USER_INFO_V0_W1_RU_START_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W1_RU_START_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W1_RU_START, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W1_RU_START_S)); \
    } while (0)


#define HTT_UL_OFDMA_USER_INFO_V0_W1_RU_SIZE_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W1_RU_SIZE_M) >> HTT_UL_OFDMA_USER_INFO_V0_W1_RU_SIZE_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W1_RU_SIZE_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W1_RU_SIZE, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W1_RU_SIZE_S)); \
    } while (0)


#define HTT_UL_OFDMA_USER_INFO_V0_W1_TRIG_TYP_GET(word)    \
    (((word) & HTT_UL_OFDMA_USER_INFO_V0_W1_TRIG_TYP_M) >> HTT_UL_OFDMA_USER_INFO_V0_W1_TRIG_TYP_S)

#define HTT_UL_OFDMA_USER_INFO_V0_W1_TRIG_TYP_SET(word, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_UL_OFDMA_USER_INFO_V0_W1_RU_TRIG_TYP, _val); \
        ((word) |= ((_val) << HTT_UL_OFDMA_USER_INFO_V0_W1_RU_TRIG_TYP_S)); \
    } while (0)

/**
 * @brief target -> host channel calibration data message
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_CHAN_CALDATA
 *
 * @brief host -> target channel calibration data message
 *
 * MSG_TYPE => HTT_H2T_MSG_TYPE_CHAN_CALDATA
 *
 * @details
 * The following field definitions describe the format of the channel
 * calibration data message sent from the target to the host when
 * MSG_TYPE is HTT_T2H_MSG_TYPE_CHAN_CALDATA, and sent from the host
 * to the target when MSG_TYPE is HTT_H2T_MSG_TYPE_CHAN_CALDATA.
 * The message is defined as htt_chan_caldata_msg followed by a variable
 * number of 32-bit character values.
 *
 * |31              21|20|19   16|15  13|  12|11      8|7            0|
 * |------------------------------------------------------------------|
 * |       rsv        | A| frag  | rsv  |ck_v| sub_type|   msg type   |
 * |------------------------------------------------------------------|
 * |        payload size         |               mhz                  |
 * |------------------------------------------------------------------|
 * |      center frequency 2     |          center frequency 1        |
 * |------------------------------------------------------------------|
 * |                              check sum                           |
 * |------------------------------------------------------------------|
 * |                              payload                             |
 * |------------------------------------------------------------------|
 * message info field:
 *   - MSG_TYPE
 *     Bits 7:0
 *     Purpose: identifies this as a channel calibration data message
 *     Value: 0x25 (HTT_T2H_MSG_TYPE_CHAN_CALDATA)
 *            0x14 (HTT_H2T_MSG_TYPE_CHAN_CALDATA)
 *   - SUB_TYPE
 *     Bits 11:8
 *     Purpose: T2H: indicates whether target is providing chan cal data
 *                   to the host to store, or requesting that the host
 *                   download previously-stored data.
 *              H2T: indicates whether the host is providing the requested
 *                   channel cal data, or if it is rejecting the data
 *                   request because it does not have the requested data.
 *     Value: see HTT_T2H_MSG_CHAN_CALDATA_xxx defs
 *   - CHKSUM_VALID
 *     Bit 12
 *     Purpose: indicates if the checksum field is valid
 *     value:
 *   - FRAG
 *     Bit 19:16
 *     Purpose: indicates the fragment index for message
 *     value: 0 for first fragment, 1 for second fragment, ...
 *   - APPEND
 *     Bit 20
 *     Purpose: indicates if this is the last fragment
 *     value: 0 = final fragment, 1 = more fragments will be appended
 *
 * channel and payload size field
 *   - MHZ
 *     Bits 15:0
 *     Purpose: indicates the channel primary frequency
 *     Value:
 *   - PAYLOAD_SIZE
 *     Bits 31:16
 *     Purpose: indicates the bytes of calibration data in payload
 *     Value:
 *
 * center frequency field
 *   - CENTER FREQUENCY 1
 *     Bits 15:0
 *     Purpose: indicates the channel center frequency
 *     Value: channel center frequency, in MHz units
 *   - CENTER FREQUENCY 2
 *     Bits 31:16
 *     Purpose: indicates the secondary channel center frequency,
 *              only for 11acvht 80plus80 mode
 *     Value:  secondary channel center frequeny, in MHz units, if applicable
 *
 * checksum field
 *   - CHECK_SUM
 *     Bits 31:0
 *     Purpose: check the payload data, it is just for this fragment.
 *              This is intended for the target to check that the channel
 *              calibration data returned by the host is the unmodified data
 *              that was previously provided to the host by the target.
 *     value: checksum of fragment payload
 */
PREPACK struct htt_chan_caldata_msg {
    /* DWORD 0: message info */
    A_UINT32
        msg_type: 8,
        sub_type: 4 ,
        chksum_valid: 1, /** 1:valid, 0:invalid  */
        reserved1: 3,
        frag_idx: 4,     /** fragment index for calibration data */
        appending: 1,    /** 0: no fragment appending,
                          *  1: extra fragment appending */
        reserved2: 11;

    /* DWORD 1: channel and payload size */
    A_UINT32
        mhz: 16,          /** primary 20 MHz channel frequency in mhz */
        payload_size: 16; /** unit: bytes */

    /* DWORD 2: center frequency */
    A_UINT32
        band_center_freq1: 16, /** Center frequency 1 in MHz */
        band_center_freq2: 16; /** Center frequency 2 in MHz,
                                *  valid only for 11acvht 80plus80 mode */

    /* DWORD 3: check sum */
    A_UINT32 chksum;

    /* variable length for calibration data */
    A_UINT32   payload[1/* or more */];
} POSTPACK;

/* T2H SUBTYPE */
#define HTT_T2H_MSG_CHAN_CALDATA_REQ     0
#define HTT_T2H_MSG_CHAN_CALDATA_UPLOAD  1

/* H2T SUBTYPE */
#define HTT_H2T_MSG_CHAN_CALDATA_REJ       0
#define HTT_H2T_MSG_CHAN_CALDATA_DOWNLOAD  1

#define HTT_CHAN_CALDATA_MSG_SUB_TYPE_S    8
#define HTT_CHAN_CALDATA_MSG_SUB_TYPE_M    0x00000f00
#define HTT_CHAN_CALDATA_MSG_SUB_TYPE_GET(_var) \
    (((_var) & HTT_CHAN_CALDATA_MSG_SUB_TYPE_M) >> HTT_CHAN_CALDATA_MSG_SUB_TYPE_S)
#define HTT_CHAN_CALDATA_MSG_SUB_TYPE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_CHAN_CALDATA_MSG_SUB_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_CHAN_CALDATA_MSG_SUB_TYPE_S)); \
    } while (0)

#define HTT_CHAN_CALDATA_MSG_CHKSUM_V_S    12
#define HTT_CHAN_CALDATA_MSG_CHKSUM_V_M    0x00001000
#define HTT_CHAN_CALDATA_MSG_CHKSUM_V_GET(_var) \
    (((_var) & HTT_CHAN_CALDATA_MSG_CHKSUM_V_M) >> HTT_CHAN_CALDATA_MSG_CHKSUM_V_S)
#define HTT_CHAN_CALDATA_MSG_CHKSUM_V_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_CHAN_CALDATA_MSG_CHKSUM_V, _val);  \
        ((_var) |= ((_val) << HTT_CHAN_CALDATA_MSG_CHKSUM_V_S)); \
    } while (0)


#define HTT_CHAN_CALDATA_MSG_FRAG_IDX_S    16
#define HTT_CHAN_CALDATA_MSG_FRAG_IDX_M    0x000f0000
#define HTT_CHAN_CALDATA_MSG_FRAG_IDX_GET(_var) \
    (((_var) & HTT_CHAN_CALDATA_MSG_FRAG_IDX_M) >> HTT_CHAN_CALDATA_MSG_FRAG_IDX_S)
#define HTT_CHAN_CALDATA_MSG_FRAG_IDX_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_CHAN_CALDATA_MSG_FRAG_IDX, _val);  \
        ((_var) |= ((_val) << HTT_CHAN_CALDATA_MSG_FRAG_IDX_S)); \
    } while (0)

#define HTT_CHAN_CALDATA_MSG_APPENDING_S    20
#define HTT_CHAN_CALDATA_MSG_APPENDING_M    0x00100000
#define HTT_CHAN_CALDATA_MSG_APPENDING_GET(_var) \
    (((_var) & HTT_CHAN_CALDATA_MSG_APPENDING_M) >> HTT_CHAN_CALDATA_MSG_APPENDING_S)
#define HTT_CHAN_CALDATA_MSG_APPENDING_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_CHAN_CALDATA_MSG_APPENDING, _val);  \
        ((_var) |= ((_val) << HTT_CHAN_CALDATA_MSG_APPENDING_S)); \
    } while (0)

#define HTT_CHAN_CALDATA_MSG_MHZ_S    0
#define HTT_CHAN_CALDATA_MSG_MHZ_M    0x0000ffff
#define HTT_CHAN_CALDATA_MSG_MHZ_GET(_var) \
    (((_var) & HTT_CHAN_CALDATA_MSG_MHZ_M) >> HTT_CHAN_CALDATA_MSG_MHZ_S)
#define HTT_CHAN_CALDATA_MSG_MHZ_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_CHAN_CALDATA_MSG_MHZ, _val);  \
        ((_var) |= ((_val) << HTT_CHAN_CALDATA_MSG_MHZ_S)); \
    } while (0)


#define HTT_CHAN_CALDATA_MSG_PLD_SIZE_S    16
#define HTT_CHAN_CALDATA_MSG_PLD_SIZE_M    0xffff0000
#define HTT_CHAN_CALDATA_MSG_PLD_SIZE_GET(_var) \
    (((_var) & HTT_CHAN_CALDATA_MSG_PLD_SIZE_M) >> HTT_CHAN_CALDATA_MSG_PLD_SIZE_S)
#define HTT_CHAN_CALDATA_MSG_PLD_SIZE_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_CHAN_CALDATA_MSG_PLD_SIZE, _val);  \
        ((_var) |= ((_val) << HTT_CHAN_CALDATA_MSG_PLD_SIZE_S)); \
    } while (0)


#define HTT_CHAN_CALDATA_MSG_FREQ1_S    0
#define HTT_CHAN_CALDATA_MSG_FREQ1_M    0x0000ffff
#define HTT_CHAN_CALDATA_MSG_FREQ1_GET(_var) \
    (((_var) & HTT_CHAN_CALDATA_MSG_FREQ1_M) >> HTT_CHAN_CALDATA_MSG_FREQ1_S)
#define HTT_CHAN_CALDATA_MSG_FREQ1_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_CHAN_CALDATA_MSG_FREQ1, _val);  \
        ((_var) |= ((_val) << HTT_CHAN_CALDATA_MSG_FREQ1_S)); \
    } while (0)

#define HTT_CHAN_CALDATA_MSG_FREQ2_S    16
#define HTT_CHAN_CALDATA_MSG_FREQ2_M    0xffff0000
#define HTT_CHAN_CALDATA_MSG_FREQ2_GET(_var) \
    (((_var) & HTT_CHAN_CALDATA_MSG_FREQ2_M) >> HTT_CHAN_CALDATA_MSG_FREQ2_S)
#define HTT_CHAN_CALDATA_MSG_FREQ2_SET(_var, _val) \
    do {                                                     \
        HTT_CHECK_SET_VAL(HTT_CHAN_CALDATA_MSG_FREQ2, _val);  \
        ((_var) |= ((_val) << HTT_CHAN_CALDATA_MSG_FREQ2_S)); \
    } while (0)


/**
 * @brief target -> host FSE CMEM based send
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_FSE_CMEM_BASE_SEND
 *
 * @details
 *  HTT_T2H_MSG_TYPE_FSE_CMEM_BASE_SEND message is sent by the target when
 *  FSE placement in CMEM is enabled.
 *
 *  This message sends the non-secure CMEM base address.
 *  It will be sent to host in response to message
 *  HTT_H2T_MSG_TYPE_RX_FSE_SETUP_CFG.
 *  The message would appear as follows:
 *
 *     |31            24|23            16|15             8|7              0|
 *     |----------------+----------------+----------------+----------------|
 *     |             reserved            |  num_entries   |   msg_type     |
 *     |----------------+----------------+----------------+----------------|
 *     |                        base_address_lo                            |
 *     |----------------+----------------+----------------+----------------|
 *     |                        base_address_hi                            |
 *     |-------------------------------------------------------------------|
 *
 * The message is interpreted as follows:
 * dword0 - b'0:7   - msg_type: This will be set to 0x27
 *                    (HTT_T2H_MSG_TYPE_FSE_CMEM_BASE_SEND)
 *          b'8:15  - number_entries: Indicated the number of entries
 *                    programmed.
 *          b'16:31 - reserved.
 * dword1 - b'0:31  - base_address_lo: Indicate lower 32 bits of
 *                    CMEM base address
 * dword2 - b'0:31 -  base_address_hi: Indicate upper 32 bits of
 *                    CMEM base address
 */

PREPACK struct htt_cmem_base_send_t {
    A_UINT32 msg_type:      8,
             num_entries:   8,
             reserved:      16;
    A_UINT32 base_address_lo;
    A_UINT32 base_address_hi;
} POSTPACK;

#define HTT_CMEM_BASE_SEND_SIZE  (sizeof(struct htt_cmem_base_send_t))

#define HTT_CMEM_BASE_SEND_NUM_ENTRIES_M                0x0000FF00
#define HTT_CMEM_BASE_SEND_NUM_ENTRIES_S                8

#define HTT_CMEM_BASE_SEND_NUM_ENTRIES_GET(_var) \
    (((_var) & HTT_CMEM_BASE_SEND_NUM_ENTRIES_M) >> \
            HTT_CMEM_BASE_SEND_NUM_ENTRIES_S)

#define HTT_CMEM_BASE_SEND_NUM_ENTRIES_SET(_var, _val) \
    do { \
        HTT_CHECK_SET_VAL(HTT_CMEM_BASE_SEND_NUM_ENTRIES, _val); \
        ((_var) |= ((_val) << HTT_SRING_SETUP_DONE_PDEV_ID_S)); \
    } while (0)

/**
 *  @brief - HTT PPDU ID format
 *
 *   @details
 *    The following field definitions describe the format of the PPDU ID.
 *    The PPDU ID is truncated to 24 bits for TLVs from TQM.
 *
 *  |31 30|29        24|     23|22 21|20   19|18  17|16     12|11            0|
 *  +--------------------------------------------------------------------------
 *  |rsvd |seq_cmd_type|tqm_cmd|rsvd |seq_idx|mac_id| hwq_ id |      sch id   |
 *  +--------------------------------------------------------------------------
 *
 *   sch id :Schedule command id
 *   Bits [11 : 0] : monotonically increasing counter to track the
 *   PPDU posted to a specific transmit queue.
 *
 *   hwq_id: Hardware Queue ID.
 *   Bits [16 : 12] : Indicates the queue id in the hardware transmit queue.
 *
 *   mac_id: MAC ID
 *   Bits [18 : 17] : LMAC ID obtained from the whal_mac_struct
 *
 *   seq_idx: Sequence index.
 *   Bits [21 : 19] : Sequence index indicates all the PPDU belonging to
 *   a particular TXOP.
 *
 *   tqm_cmd: HWSCH/TQM flag.
 *   Bit [23] : Always set to 0.
 *
 *   seq_cmd_type: Sequence command type.
 *   Bit [29 : 24] : Indicates the frame type for the current sequence.
 *   Refer to enum HTT_STATS_FTYPE for values.
 */
PREPACK struct htt_ppdu_id {
    A_UINT32
        sch_id:         12,
        hwq_id:          5,
        mac_id:          2,
        seq_idx:         2,
        reserved1:       2,
        tqm_cmd:         1,
        seq_cmd_type:    6,
        reserved2:       2;
} POSTPACK;

#define HTT_PPDU_ID_SCH_ID_S    0
#define HTT_PPDU_ID_SCH_ID_M    0x00000fff
#define HTT_PPDU_ID_SCH_ID_GET(_var) \
    (((_var) & HTT_PPDU_ID_SCH_ID_M) >> HTT_PPDU_ID_SCH_ID_S)

#define HTT_PPDU_ID_SCH_ID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_PPDU_ID_SCH_ID, _val);  \
        ((_var) |= ((_val) << HTT_PPDU_ID_SCH_ID_S)); \
    } while (0)

#define HTT_PPDU_ID_HWQ_ID_S    12
#define HTT_PPDU_ID_HWQ_ID_M    0x0001f000
#define HTT_PPDU_ID_HWQ_ID_GET(_var) \
    (((_var) & HTT_PPDU_ID_HWQ_ID_M) >> HTT_PPDU_ID_HWQ_ID_S)

#define HTT_PPDU_ID_HWQ_ID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_PPDU_ID_HWQ_ID, _val);  \
        ((_var) |= ((_val) << HTT_PPDU_ID_HWQ_ID_S)); \
    } while (0)

#define HTT_PPDU_ID_MAC_ID_S    17
#define HTT_PPDU_ID_MAC_ID_M    0x00060000
#define HTT_PPDU_ID_MAC_ID_GET(_var) \
    (((_var) & HTT_PPDU_ID_MAC_ID_M) >> HTT_PPDU_ID_MAC_ID_S)

#define HTT_PPDU_ID_MAC_ID_SET(_var, _val) \
    do {                                            \
        HTT_CHECK_SET_VAL(HTT_PPDU_ID_MAC_ID, _val);  \
        ((_var) |= ((_val) << HTT_PPDU_ID_MAC_ID_S)); \
    } while (0)

#define HTT_PPDU_ID_SEQ_IDX_S    19
#define HTT_PPDU_ID_SEQ_IDX_M    0x00180000
#define HTT_PPDU_ID_SEQ_IDX_GET(_var) \
    (((_var) & HTT_PPDU_ID_SEQ_IDX_M) >> HTT_PPDU_ID_SEQ_IDX_S)

#define HTT_PPDU_ID_SEQ_IDX_SET(_var, _val) \
    do {                                            \
        HTT_CHECK_SET_VAL(HTT_PPDU_ID_SEQ_IDX, _val);  \
        ((_var) |= ((_val) << HTT_PPDU_ID_SEQ_IDX_S)); \
    } while (0)

#define HTT_PPDU_ID_TQM_CMD_S    23
#define HTT_PPDU_ID_TQM_CMD_M    0x00800000
#define HTT_PPDU_ID_TQM_CMD_GET(_var) \
    (((_var) & HTT_PPDU_ID_TQM_CMD_M) >> HTT_PPDU_ID_TQM_CMD_S)

#define HTT_PPDU_ID_TQM_CMD_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_PPDU_ID_TQM_CMD, _val);  \
        ((_var) |= ((_val) << HTT_PPDU_ID_TQM_CMD_S)); \
    } while (0)

#define HTT_PPDU_ID_SEQ_CMD_TYPE_S    24
#define HTT_PPDU_ID_SEQ_CMD_TYPE_M    0x3f000000
#define HTT_PPDU_ID_SEQ_CMD_TYPE_GET(_var) \
    (((_var) & HTT_PPDU_ID_SEQ_CMD_TYPE_M) >> HTT_PPDU_ID_SEQ_CMD_TYPE_S)

#define HTT_PPDU_ID_SEQ_CMD_TYPE_SET(_var, _val) \
    do {                                                 \
        HTT_CHECK_SET_VAL(HTT_PPDU_ID_SEQ_CMD_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_PPDU_ID_SEQ_CMD_TYPE_S)); \
    } while (0)

/**
 * @brief target -> RX PEER METADATA V0 format
 * Host will know the peer metadata version from the wmi_service_ready_ext2
 * message from target, and will confirm to the target which peer metadata
 * version to use in the wmi_init message.
 *
 * The following diagram shows the format of the RX PEER METADATA.
 *
 * |31             24|23             16|15              8|7               0|
 * |-----------------------------------------------------------------------|
 * |    Reserved     |     VDEV ID     |              PEER ID              |
 * |-----------------------------------------------------------------------|
 */
PREPACK struct htt_rx_peer_metadata_v0 {
    A_UINT32
        peer_id:         16,
        vdev_id:         8,
        reserved1:       8;
} POSTPACK;

#define HTT_RX_PEER_META_DATA_V0_PEER_ID_S    0
#define HTT_RX_PEER_META_DATA_V0_PEER_ID_M    0x0000ffff
#define HTT_RX_PEER_META_DATA_V0_PEER_ID_GET(_var) \
    (((_var) & HTT_RX_PEER_META_DATA_V0_PEER_ID_M) >> HTT_RX_PEER_META_DATA_V0_PEER_ID_S)

#define HTT_RX_PEER_META_DATA_V0_PEER_ID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_META_DATA_V0_PEER_ID, _val);  \
        ((_var) |= ((_val) << HTT_RX_PEER_META_DATA_V0_PEER_ID_S)); \
    } while (0)

#define HTT_RX_PEER_META_DATA_V0_VDEV_ID_S    16
#define HTT_RX_PEER_META_DATA_V0_VDEV_ID_M    0x00ff0000
#define HTT_RX_PEER_META_DATA_V0_VDEV_ID_GET(_var) \
    (((_var) & HTT_RX_PEER_META_DATA_V0_VDEV_ID_M) >> HTT_RX_PEER_META_DATA_V0_VDEV_ID_S)

#define HTT_RX_PEER_META_DATA_V0_VDEV_ID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_META_DATA_V0_VDEV_ID, _val);  \
        ((_var) |= ((_val) << HTT_RX_PEER_META_DATA_V0_VDEV_ID_S)); \
    } while (0)

/**
 * @brief target -> RX PEER METADATA V1 format
 * Host will know the peer metadata version from the wmi_service_ready_ext2
 * message from target, and will confirm to the target which peer metadata
 * version to use in the wmi_init message.
 *
 * The following diagram shows the format of the RX PEER METADATA V1 format.
 *
 * |31 29|28   26|25   24|23        16|15 14|   13  |12                   0|
 * |-----------------------------------------------------------------------|
 * |Rsvd2|CHIP ID|LMAC ID|  VDEV ID   |Rsvd1|ML PEER| SW PEER ID/ML PEER ID|
 * |-----------------------------------------------------------------------|
 */
PREPACK struct htt_rx_peer_metadata_v1 {
    A_UINT32
        peer_id:         13,
        ml_peer_valid:   1,
        reserved1:       2,
        vdev_id:         8,
        lmac_id:         2,
        chip_id:         3,
        reserved2:       3;
} POSTPACK;

#define HTT_RX_PEER_META_DATA_V1_PEER_ID_S    0
#define HTT_RX_PEER_META_DATA_V1_PEER_ID_M    0x00001fff
#define HTT_RX_PEER_META_DATA_V1_PEER_ID_GET(_var) \
    (((_var) & HTT_RX_PEER_META_DATA_V1_PEER_ID_M) >> HTT_RX_PEER_META_DATA_V1_PEER_ID_S)

#define HTT_RX_PEER_META_DATA_V1_PEER_ID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_META_DATA_V1_PEER_ID, _val);  \
        ((_var) |= ((_val) << HTT_RX_PEER_META_DATA_V1_PEER_ID_S)); \
    } while (0)

#define HTT_RX_PEER_META_DATA_V1_ML_PEER_VALID_S    13
#define HTT_RX_PEER_META_DATA_V1_ML_PEER_VALID_M    0x00002000
#define HTT_RX_PEER_META_DATA_V1_ML_PEER_VALID_GET(_var) \
    (((_var) & HTT_RX_PEER_META_DATA_V1_ML_PEER_VALID_M) >> HTT_RX_PEER_META_DATA_V1_ML_PEER_VALID_S)

#define HTT_RX_PEER_META_DATA_V1_ML_PEER_VALID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_META_DATA_V1_ML_PEER_VALID, _val);  \
        ((_var) |= ((_val) << HTT_RX_PEER_META_DATA_V1_ML_PEER_VALID_S)); \
    } while (0)

#define HTT_RX_PEER_META_DATA_V1_VDEV_ID_S    16
#define HTT_RX_PEER_META_DATA_V1_VDEV_ID_M    0x00ff0000
#define HTT_RX_PEER_META_DATA_V1_VDEV_ID_GET(_var) \
    (((_var) & HTT_RX_PEER_META_DATA_V1_VDEV_ID_M) >> HTT_RX_PEER_META_DATA_V1_VDEV_ID_S)

#define HTT_RX_PEER_META_DATA_V1_VDEV_ID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_META_DATA_V1_VDEV_ID, _val);  \
        ((_var) |= ((_val) << HTT_RX_PEER_META_DATA_V1_VDEV_ID_S)); \
    } while (0)

#define HTT_RX_PEER_META_DATA_V1_LMAC_ID_S    24
#define HTT_RX_PEER_META_DATA_V1_LMAC_ID_M    0x03000000
#define HTT_RX_PEER_META_DATA_V1_LMAC_ID_GET(_var) \
    (((_var) & HTT_RX_PEER_META_DATA_V1_LMAC_ID_M) >> HTT_RX_PEER_META_DATA_V1_LMAC_ID_S)

#define HTT_RX_PEER_META_DATA_V1_LMAC_ID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_META_DATA_V1_LMAC_ID, _val);  \
        ((_var) |= ((_val) << HTT_RX_PEER_META_DATA_V1_LMAC_ID_S)); \
    } while (0)

#define HTT_RX_PEER_META_DATA_V1_CHIP_ID_S    26
#define HTT_RX_PEER_META_DATA_V1_CHIP_ID_M    0x1c000000
#define HTT_RX_PEER_META_DATA_V1_CHIP_ID_GET(_var) \
    (((_var) & HTT_RX_PEER_META_DATA_V1_CHIP_ID_M) >> HTT_RX_PEER_META_DATA_V1_CHIP_ID_S)

#define HTT_RX_PEER_META_DATA_V1_CHIP_ID_SET(_var, _val) \
    do {                                             \
        HTT_CHECK_SET_VAL(HTT_RX_PEER_META_DATA_V1_CHIP_ID, _val);  \
        ((_var) |= ((_val) << HTT_RX_PEER_META_DATA_V1_CHIP_ID_S)); \
    } while (0)

/*
 * In some systems, the host SW wants to specify priorities between
 * different MSDU / flow queues within the same peer-TID.
 * The below enums are used for the host to identify to the target
 * which MSDU queue's priority it wants to adjust.
 */

/*
 * The MSDUQ index describe index of TCL HW, where each index is
 * used for queuing particular types of MSDUs.
 * The different MSDU queue types are defined in HTT_MSDU_QTYPE.
 */
enum HTT_MSDUQ_INDEX {
    HTT_MSDUQ_INDEX_NON_UDP, /* NON UDP MSDUQ index */
    HTT_MSDUQ_INDEX_UDP,     /* UDP MSDUQ index */

    HTT_MSDUQ_INDEX_CUSTOM_PRIO_0, /* Latency priority 0 index */
    HTT_MSDUQ_INDEX_CUSTOM_PRIO_1, /* Latency priority 1 index */

    HTT_MSDUQ_INDEX_CUSTOM_EXT_PRIO_0, /* High num TID cases/ MLO dedicate link cases */
    HTT_MSDUQ_INDEX_CUSTOM_EXT_PRIO_1, /* High num TID cases/ MLO dedicate link cases */

    HTT_MSDUQ_INDEX_CUSTOM_EXT_PRIO_2, /* High num TID cases/ MLO dedicate link cases */
    HTT_MSDUQ_INDEX_CUSTOM_EXT_PRIO_3, /* High num TID cases/ MLO dedicate link cases */

    HTT_MSDUQ_MAX_INDEX,
};

/* MSDU qtype definition */
enum HTT_MSDU_QTYPE {
    /*
     * The LATENCY_CRIT_0 and LATENCY_CRIT_1 queue types don't have a fixed
     * relative priority.  Instead, the relative priority of CRIT_0 versus
     * CRIT_1 is controlled by the FW, through the configuration parameters
     * it applies to the queues.
     */
    HTT_MSDU_QTYPE_LATENCY_CRIT_0, /* Specified MSDUQ index used for latency critical 0 */
    HTT_MSDU_QTYPE_LATENCY_CRIT_1, /* Specified MSDUQ index used for latency critical 1 */
    HTT_MSDU_QTYPE_UDP, /* Specifies MSDUQ index used for UDP flow */
    HTT_MSDU_QTYPE_NON_UDP, /* Specifies MSDUQ index used for non-udp flow */
    HTT_MSDU_QTYPE_HOL, /* Specified MSDUQ index used for Head of Line */


    /* New MSDU_QTYPE should be added above this line */
    /*
     * Below QTYPE_MAX will increase if additional QTYPEs are defined
     * in the future. Hence HTT_MSDU_QTYPE_MAX can't be used in
     * any host/target message definitions.  The QTYPE_MAX value can
     * only be used internally within the host or within the target.
     * If host or target find a qtype value is >= HTT_MSDU_QTYPE_MAX
     * it must regard the unexpected value as a default qtype value,
     * or ignore it.
     */
    HTT_MSDU_QTYPE_MAX,
    HTT_MSDU_QTYPE_NOT_IN_USE = 255, /* corresponding MSDU index is not in use */
};

enum HTT_MSDUQ_LEGACY_FLOW_INDEX {
    HTT_MSDUQ_LEGACY_HI_PRI_FLOW_INDEX = 0,
    HTT_MSDUQ_LEGACY_LO_PRI_FLOW_INDEX = 1,
    HTT_MSDUQ_LEGACY_UDP_FLOW_INDEX = 2,
    HTT_MSDUQ_LEGACY_NON_UDP_FLOW_INDEX = 3,
};

/**
 * @brief target -> host mlo timestamp offset indication
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_MLO_TIMESTAMP_OFFSET_IND
 *
 * @details
 * The following field definitions describe the format of the HTT target
 * to host mlo timestamp offset indication message.
 *
 *
 * |31                         16|15    12|11   10|9     8|7            0 |
 * |----------------------------------------------------------------------|
 * |      mac_clk_freq_mhz       |  rsvd  |chip_id|pdev_id|    msg type   |
 * |----------------------------------------------------------------------|
 * |                      Sync time stamp lo in us                        |
 * |----------------------------------------------------------------------|
 * |                      Sync time stamp hi in us                        |
 * |----------------------------------------------------------------------|
 * |                  mlo time stamp offset lo in us                      |
 * |----------------------------------------------------------------------|
 * |                  mlo time stamp offset hi in us                      |
 * |----------------------------------------------------------------------|
 * |           mlo time stamp offset clocks in clock ticks                |
 * |----------------------------------------------------------------------|
 * |31  26|25                   16|15                                   0 |
 * |rsvd2 | mlo time stamp        | mlo time stamp compensation in us     |
 * |      | compensation in clks  |                                       |
 * |----------------------------------------------------------------------|
 * |31           22|21                                                  0 |
 * |      rsvd 3   | mlo time stamp comp timer period                     |
 * |----------------------------------------------------------------------|
 *  The message is interpreted as follows:
 *
 *  dword0 - b'0:7   - msg_type: This will be set to
 *                     HTT_T2H_MSG_TYPE_MLO_TIMESTAMP_OFFSET_IND
 *                     value: 0x28
 *
 *  dword0 - b'9:8   - pdev_id
 *
 *  dword0 - b'11:10 - chip_id
 *
 *  dword0 - b'15:12 - rsvd1: Reserved for future use
 *
 *  dword0 - b'31:16 - mac clock frequency of the mac HW block in MHz
 *
 *  dword1 - b'31:0  - lower 32 bits of the WLAN global time stamp (in us) at
 *                     which last sync interrupt was received
 *
 *  dword2 - b'31:0  - upper 32 bits of the WLAN global time stamp (in us) at
 *                     which last sync interrupt was received
 *
 *  dword3 - b'31:0  - lower 32 bits of the MLO time stamp offset in us
 *
 *  dword4 - b'31:0  - upper 32 bits of the MLO time stamp offset in us
 *
 *  dword5 - b'31:0  - MLO time stamp offset in clock ticks for sub us
 *
 *  dword6 - b'15:0  - MLO time stamp compensation applied in us
 *
 *  dword6 - b'25:16 - MLO time stamp compensation applied in clock ticks
 *                     for sub us resolution
 *
 *  dword6 - b'31:26 - rsvd2: Reserved for future use
 *
 *  dword7 - b'21:0  - period of MLO compensation timer at which compensation
 *                     is applied, in us
 *
 *  dword7 - b'31:22 - rsvd3: Reserved for future use
 */

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MSG_TYPE_M         0x000000FF
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MSG_TYPE_S         0

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_PDEV_ID_M          0x00000300
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_PDEV_ID_S          8

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_CHIP_ID_M          0x00000C00
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_CHIP_ID_S          10

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MAC_CLK_FREQ_MHZ_M 0xFFFF0000
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MAC_CLK_FREQ_MHZ_S 16

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_US_M        0x0000FFFF
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_US_S        0

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_CLKS_M      0x03FF0000
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_CLKS_S      16

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_PERIOD_US_M 0x003FFFFF
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_PERIOD_US_S 0

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MSG_TYPE_GET(_var) \
    (((_var) & HTT_T2H_MLO_TIMESTAMP_OFFSET_MSG_TYPE_M) >> HTT_T2H_MLO_TIMESTAMP_OFFSET_MSG_TYPE_S)
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MSG_TYPE_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_MLO_TIMESTAMP_OFFSET_MSG_TYPE, _val);  \
        ((_var) |= ((_val) << HTT_T2H_MLO_TIMESTAMP_OFFSET_MSG_TYPE_S)); \
    } while (0)

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_PDEV_ID_GET(_var) \
    (((_var) & HTT_T2H_MLO_TIMESTAMP_OFFSET_PDEV_ID_M) >> HTT_T2H_MLO_TIMESTAMP_OFFSET_PDEV_ID_S)
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_PDEV_ID_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_MLO_TIMESTAMP_OFFSET_PDEV_ID, _val);  \
        ((_var) |= ((_val) << HTT_T2H_MLO_TIMESTAMP_OFFSET_PDEV_ID_S)); \
    } while (0)

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_CHIP_ID_GET(_var) \
    (((_var) & HTT_T2H_MLO_TIMESTAMP_OFFSET_CHIP_ID_M) >> HTT_T2H_MLO_TIMESTAMP_OFFSET_CHIP_ID_S)
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_CHIP_ID_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_MLO_TIMESTAMP_OFFSET_CHIP_ID, _val);  \
        ((_var) |= ((_val) << HTT_T2H_MLO_TIMESTAMP_OFFSET_CHIP_ID_S)); \
    } while (0)

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MAC_CLK_FREQ_MHZ_GET(_var) \
    (((_var) & HTT_T2H_MLO_TIMESTAMP_OFFSET_MAC_CLK_FREQ_MHZ_M) >> \
    HTT_T2H_MLO_TIMESTAMP_OFFSET_MAC_CLK_FREQ_MHZ_S)
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MAC_CLK_FREQ_MHZ_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_MLO_TIMESTAMP_OFFSET_MAC_CLK_FREQ_MHZ, _val);  \
        ((_var) |= ((_val) << HTT_T2H_MLO_TIMESTAMP_OFFSET_MAC_CLK_FREQ_MHZ_S)); \
    } while (0)

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_US_GET(_var) \
    (((_var) & HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_US_M) >> \
    HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_US_S)
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_US_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_US, _val);  \
        ((_var) |= ((_val) << HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_US_S)); \
    } while (0)

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_CLKS_GET(_var) \
    (((_var) & HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_CLKS_M) >> \
      HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_CLKS_S)
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_CLKS_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_CLKS, _val);  \
        ((_var) |= ((_val) << HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_CLKS_S)); \
    } while (0)

#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_PERIOD_US_GET(_var) \
    (((_var) & HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_PERIOD_US_M) >> \
      HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_PERIOD_US_S)
#define HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_PERIOD_US_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_PERIOD_US, _val);  \
        ((_var) |= ((_val) << HTT_T2H_MLO_TIMESTAMP_OFFSET_MLO_TIMESTAMP_COMP_PERIOD_US_S)); \
    } while (0)

typedef struct {
    A_UINT32 msg_type:          8, /* bits  7:0  */
             pdev_id:           2, /* bits  9:8  */
             chip_id:           2, /* bits 11:10 */
             reserved1:         4, /* bits 15:12 */
             mac_clk_freq_mhz: 16; /* bits 31:16 */
    A_UINT32 sync_timestamp_lo_us;
    A_UINT32 sync_timestamp_hi_us;
    A_UINT32 mlo_timestamp_offset_lo_us;
    A_UINT32 mlo_timestamp_offset_hi_us;
    A_UINT32 mlo_timestamp_offset_clks;
    A_UINT32 mlo_timestamp_comp_us:   16, /* bits 15:0  */
             mlo_timestamp_comp_clks: 10, /* bits 25:16 */
             reserved2:                6; /* bits 31:26 */
    A_UINT32 mlo_timestamp_comp_timer_period_us: 22, /* bits 21:0  */
             reserved3:                          10; /* bits 31:22 */
} htt_t2h_mlo_offset_ind_t;

/*
 * @brief target -> host VDEV TX RX STATS
 *
 * MSG_TYPE => HTT_T2H_MSG_TYPE_VDEVS_TXRX_STATS_PERIODIC_IND
 *
 * @details
 *  HTT_T2H_MSG_TYPE_VDEVS_TXRX_STATS_PERIODIC_IND message is sent by the target
 *  every periodic interval programmed in HTT_H2T_MSG_TYPE_VDEVS_TXRX_STATS_CFG.
 *  After the host sends an initial HTT_H2T_MSG_TYPE_VDEVS_TXRX_STATS_CFG,
 *  this HTT_T2H_MSG_TYPE_VDEVS_TXRX_STATS_PERIODIC_IND message will be sent
 *  periodically by target even in the absence of any further HTT request
 *  messages from host.
 *
 *  The message is formatted as follows:
 *
 *     |31                             16|15             8|7              0|
 *     |---------------------------------+----------------+----------------|
 *     |            payload_size         |     pdev_id    |   msg_type     |
 *     |---------------------------------+----------------+----------------|
 *     |                             reserved0                             |
 *     |-------------------------------------------------------------------|
 *     |                             reserved1                             |
 *     |-------------------------------------------------------------------|
 *     |                             reserved2                             |
 *     |-------------------------------------------------------------------|
 *     |                                                                   |
 *     |                    VDEV specific Tx Rx stats info                 |
 *     |                                                                   |
 *     |-------------------------------------------------------------------|
 *
 * The message is interpreted as follows:
 * dword0 - b'0:7   - msg_type: This will be set to 0x2c
 *                    (HTT_T2H_MSG_TYPE_VDEVS_TXRX_STATS_PERIODIC_IND)
 *          b'8:15  - pdev_id
 *          b'16:31 - size in bytes of the payload that follows the 16-byte
 *                    message header fields (msg_type through reserved2)
 * dword1 - b'0:31  - reserved0.
 * dword2 - b'0:31  - reserved1.
 * dword3 - b'0:31  - reserved2.
 */
typedef struct {
    A_UINT32 msg_type:       8,
             pdev_id:        8,
             payload_size:  16;
    A_UINT32 reserved0;
    A_UINT32 reserved1;
    A_UINT32 reserved2;
} htt_t2h_vdevs_txrx_stats_periodic_hdr_t;

#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_HDR_SIZE          16

#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PDEV_ID_M         0x0000FF00
#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PDEV_ID_S         8

#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PDEV_ID_GET(_var) \
    (((_var) & HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PDEV_ID_M) >> HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PDEV_ID_S)
#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PDEV_ID_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PDEV_ID, _val);  \
        ((_var) |= ((_val) << HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PDEV_ID_S)); \
    } while (0)

#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PAYLOAD_SIZE_M    0xFFFF0000
#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PAYLOAD_SIZE_S    16

#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PAYLOAD_SIZE_GET(_var) \
    (((_var) & HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PAYLOAD_SIZE_M) >> HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PAYLOAD_SIZE_S)
#define HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PAYLOAD_SIZE_SET(_var, _val)            \
    do {                                                   \
        HTT_CHECK_SET_VAL(HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PAYLOAD_SIZE, _val);  \
        ((_var) |= ((_val) << HTT_T2H_VDEVS_TXRX_STATS_PERIODIC_IND_PAYLOAD_SIZE_S)); \
    } while (0)

/* SOC related stats */
typedef struct {
    htt_tlv_hdr_t tlv_hdr;

     /* When TQM is not able to find the peers during Tx, then it drops the packets
     *  This can be due to either the peer is deleted or deletion is ongoing
     * */
    A_UINT32 inv_peers_msdu_drop_count_lo;
    A_UINT32 inv_peers_msdu_drop_count_hi;
} htt_t2h_soc_txrx_stats_common_tlv;

/* VDEV HW Tx/Rx stats */
typedef struct {
    htt_tlv_hdr_t tlv_hdr;
    A_UINT32 vdev_id;

    /* Rx msdu byte cnt */
    A_UINT32 rx_msdu_byte_cnt_lo;
    A_UINT32 rx_msdu_byte_cnt_hi;

    /* Rx msdu cnt */
    A_UINT32 rx_msdu_cnt_lo;
    A_UINT32 rx_msdu_cnt_hi;

    /* tx msdu byte cnt */
    A_UINT32 tx_msdu_byte_cnt_lo;
    A_UINT32 tx_msdu_byte_cnt_hi;

    /* tx msdu cnt */
    A_UINT32 tx_msdu_cnt_lo;
    A_UINT32 tx_msdu_cnt_hi;

    /* tx excessive retry discarded msdu cnt*/
    A_UINT32 tx_msdu_excessive_retry_discard_cnt_lo;
    A_UINT32 tx_msdu_excessive_retry_discard_cnt_hi;

    /* TX congestion ctrl msdu drop cnt */
    A_UINT32 tx_msdu_cong_ctrl_drop_cnt_lo;
    A_UINT32 tx_msdu_cong_ctrl_drop_cnt_hi;

    /* discarded tx msdus cnt coz of time to live expiry */
    A_UINT32 tx_msdu_ttl_expire_drop_cnt_lo;
    A_UINT32 tx_msdu_ttl_expire_drop_cnt_hi;
} htt_t2h_vdev_txrx_stats_hw_stats_tlv;

#endif