/*
* pt_core.c
* Parade TrueTouch(TM) Standard Product Core Module.
* For use with Parade touchscreen controllers.
* Supported parts include:
* TMA5XX
* TMA448
* TMA445A
* TT21XXX
* TT31XXX
* TT4XXXX
* TT7XXX
* TC3XXX
*
* Copyright (C) 2015-2020 Parade Technologies
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2, and only version 2, as published by the
* Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Contact Parade Technologies at www.paradetech.com <ttdrivers@paradetech.com>
*/
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/kthread.h>
#include <linux/suspend.h>
#include <glink_interface.h>
#include <linux/remoteproc/qcom_rproc.h>
#include "pt_regs.h"
#if defined(CONFIG_PANEL_NOTIFIER)
#include <linux/soc/qcom/panel_event_notifier.h>
#endif
#define PINCTRL_STATE_ACTIVE "pmx_ts_active"
#define PINCTRL_STATE_SUSPEND "pmx_ts_suspend"
#define PINCTRL_STATE_RELEASE "pmx_ts_release"
#define FT_VTG_MIN_UV 2800000
#define FT_VTG_MAX_UV 2800000
#define FT_I2C_VTG_MIN_UV 1800000
#define FT_I2C_VTG_MAX_UV 1800000
#define PWR_SUSPEND_LOAD_UA 165
#define I2C_SUSPEND_LOAD_UA 100
#define PWR_ACTIVE_LOAD_MA 12000
#define I2C_ACTIVE_LOAD_MA 30000
#define PT_CORE_STARTUP_RETRY_COUNT 3
#define PT_STATUS_STR_LEN (50)
#define PT_DATA_SIZE (2 * 256)
#if defined(CONFIG_DRM) || defined(CONFIG_PANEL_NOTIFIER)
static struct drm_panel *active_panel;
#endif
MODULE_FIRMWARE(PT_FW_FILE_NAME);
#define ENABLE_I2C_REG_ONLY
enum core_states {
STATE_NONE,
STATE_RESUME,
STATE_SUSPEND
};
#ifdef ENABLE_I2C_REG_ONLY
static int pt_enable_i2c_regulator(struct pt_core_data *cd, bool en);
#endif
#define PT_AMBIENT_MODE
#ifdef PT_AMBIENT_MODE
static int pt_device_exit(struct i2c_client *client);
int pt_device_entry(struct device *dev,
u16 irq, size_t xfer_buf_size);
#endif
static const char *pt_driver_core_name = PT_CORE_NAME;
static const char *pt_driver_core_version = PT_DRIVER_VERSION;
static const char *pt_driver_core_date = PT_DRIVER_DATE;
enum core_states pt_core_state = STATE_NONE;
uint32_t pt_slate_resp_ack;
struct pt_hid_field {
int report_count;
int report_size;
int size; /* report_count * report_size */
int offset;
int data_type;
int logical_min;
int logical_max;
/* Usage Page (Hi 16 bit) + Usage (Lo 16 bit) */
u32 usage_page;
u32 collection_usage_pages[PT_HID_MAX_COLLECTIONS];
struct pt_hid_report *report;
bool record_field;
};
struct pt_hid_report {
u8 id;
u8 type;
int size;
struct pt_hid_field *fields[PT_HID_MAX_FIELDS];
int num_fields;
int record_field_index;
int header_size;
int record_size;
u32 usage_page;
};
struct atten_node {
struct list_head node;
char *id;
struct device *dev;
int (*func)(struct device *dev);
int mode;
};
struct param_node {
struct list_head node;
u8 id;
u32 value;
u8 size;
};
struct module_node {
struct list_head node;
struct pt_module *module;
void *data;
};
struct pt_hid_cmd {
u8 opcode;
u8 report_type;
union {
u8 report_id;
u8 power_state;
};
u8 has_data_register;
size_t write_length;
u8 *write_buf;
u8 *read_buf;
u8 wait_interrupt;
u8 reset_cmd;
u16 timeout_ms;
};
struct pt_hid_output {
u8 cmd_type;
u16 length;
u8 command_code;
size_t write_length;
u8 *write_buf;
u8 novalidate;
u8 reset_expected;
u16 timeout_ms;
};
#define SET_CMD_OPCODE(byte, opcode) SET_CMD_LOW(byte, opcode)
#define SET_CMD_REPORT_TYPE(byte, type) SET_CMD_HIGH(byte, ((type) << 4))
#define SET_CMD_REPORT_ID(byte, id) SET_CMD_LOW(byte, id)
#define CREATE_PIP1_FW_CMD(command) \
.cmd_type = PIP1_CMD_TYPE_FW, \
.command_code = command
#define CREATE_PIP1_BL_CMD(command) \
.cmd_type = PIP1_CMD_TYPE_BL, \
.command_code = command
#define PT_MAX_PR_BUF_SIZE 2048
/*******************************************************************************
* FUNCTION: pt_pr_buf
*
* SUMMARY: Print out the contents of a buffer to kmsg based on the debug level
*
* RETURN: Void
*
* PARAMETERS:
* *dev - pointer to Device structure
* debug_level - requested debug level to print at
* *buf - pointer to buffer to print
* buf_len - size of buf
* *data_name - Descriptive name of data prefixed to data
******************************************************************************/
void pt_pr_buf(struct device *dev, u8 debug_level, u8 *buf,
u16 buf_len, const char *data_name)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int i;
ssize_t pr_buf_index = 0;
int max_size;
/* only proceed if valid debug level and there is data to print */
if (debug_level <= cd->debug_level && buf_len > 0) {
char *pr_buf = kzalloc(PT_MAX_PR_BUF_SIZE, GFP_KERNEL);
if (!pr_buf)
return;
/*
* With a space each printed char takes 3 bytes, subtract
* the length of the data_name prefix as well as 11 bytes
* for the " [0..xxx]: " printed before the data.
*/
max_size = (PT_MAX_PR_BUF_SIZE - sizeof(data_name) - 11) / 3;
/* Ensure pr_buf_index stays within the 1018 size */
pr_buf_index += scnprintf(pr_buf, PT_MAX_PR_BUF_SIZE, "%s [0..%d]: ",
data_name);
for (i = 0; i < buf_len && i < max_size; i++)
pr_buf_index += scnprintf(pr_buf + pr_buf_index,
PT_MAX_PR_BUF_SIZE, "%02X ", buf[i]);
pt_debug(dev, debug_level, "%s\n", pr_buf);
kfree(pr_buf);
}
}
EXPORT_SYMBOL_GPL(pt_pr_buf);
#ifdef TTHE_TUNER_SUPPORT
/*******************************************************************************
* FUNCTION: tthe_print
*
* SUMMARY: Format data name and time stamp as the header and format the
* content of input buffer with hex base to "tthe_buf". And then wake up event
* semaphore for tthe debugfs node.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *buf - pointer to input buffer
* buf_len - size of input buffer
* *data_name - pointer to data name
******************************************************************************/
static int tthe_print(struct pt_core_data *cd, u8 *buf, int buf_len,
const u8 *data_name)
{
int name_len = strlen(data_name);
int i, n;
u8 *p;
int remain;
u8 data_name_with_time_stamp[100];
/* Prepend timestamp, if requested, to data_name */
if (cd->show_timestamp) {
scnprintf(data_name_with_time_stamp,
sizeof(data_name_with_time_stamp),
"[%u] %s", pt_get_time_stamp(), data_name);
data_name = data_name_with_time_stamp;
name_len = strlen(data_name);
}
mutex_lock(&cd->tthe_lock);
if (!cd->tthe_buf)
goto exit;
/* Add 1 due to the '\n' that is appended at the end */
if (cd->tthe_buf_len + name_len + buf_len + 1 > cd->tthe_buf_size)
goto exit;
if (name_len + buf_len == 0)
goto exit;
remain = cd->tthe_buf_size - cd->tthe_buf_len;
if (remain < name_len)
name_len = remain;
p = cd->tthe_buf + cd->tthe_buf_len;
memcpy(p, data_name, name_len);
cd->tthe_buf_len += name_len;
p += name_len;
remain -= name_len;
*p = 0;
for (i = 0; i < buf_len; i++) {
n = scnprintf(p, remain, "%02X ", buf[i]);
if (n <= 0)
break;
p += n;
remain -= n;
cd->tthe_buf_len += n;
}
n = scnprintf(p, remain, "\n");
cd->tthe_buf_len += n;
exit:
wake_up(&cd->wait_q);
mutex_unlock(&cd->tthe_lock);
return 0;
}
/*******************************************************************************
* FUNCTION: _pt_request_tthe_print
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request to print data to the "tthe_buffer".
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static int _pt_request_tthe_print(struct device *dev, u8 *buf,
int buf_len, const u8 *data_name)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return tthe_print(cd, buf, buf_len, data_name);
}
#endif
/*******************************************************************************
* FUNCTION: pt_platform_detect_read
*
* SUMMARY: To be passed to platform dectect function to perform a read
* operation.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to Device structure
* *buf - pointer to buffer where the data read will be stored
* size - size to be read
******************************************************************************/
static int pt_platform_detect_read(struct device *dev, void *buf, int size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return pt_adap_read_default(cd, buf, size);
}
/*******************************************************************************
* FUNCTION: pt_add_parameter
*
* SUMMARY: Adds a parameter that has been altered to the parameter linked list.
* On every reset of the DUT this linked list is traversed and all
* parameters in it are restored to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* param_id - parameter ID to add
* param_value - Value corresponding to the ID
* param_size - Size of param_value
******************************************************************************/
static int pt_add_parameter(struct pt_core_data *cd,
u8 param_id, u32 param_value, u8 param_size)
{
struct param_node *param, *param_new;
/* Check if parameter already exists in the list */
spin_lock(&cd->spinlock);
list_for_each_entry(param, &cd->param_list, node) {
if (param->id == param_id) {
/* Update parameter */
param->value = param_value;
pt_debug(cd->dev, DL_INFO,
"%s: Update parameter id:%d value:%d size:%d\n",
__func__, param_id, param_value, param_size);
goto exit_unlock;
}
}
spin_unlock(&cd->spinlock);
param_new = kzalloc(sizeof(*param_new), GFP_KERNEL);
if (!param_new)
return -ENOMEM;
param_new->id = param_id;
param_new->value = param_value;
param_new->size = param_size;
pt_debug(cd->dev, DL_INFO,
"%s: Add parameter id:%d value:%d size:%d\n",
__func__, param_id, param_value, param_size);
spin_lock(&cd->spinlock);
list_add(¶m_new->node, &cd->param_list);
exit_unlock:
spin_unlock(&cd->spinlock);
return 0;
}
#ifdef TTDL_DIAGNOSTICS
/*******************************************************************************
* FUNCTION: pt_erase_parameter_list
*
* SUMMARY: Empty out the entire parameter linked list of all parameter/value
* pairs. In some test cases this functionality is needed to ensure DUT
* returns to a virgin state after a reset and no parameters are restored.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_erase_parameter_list(struct pt_core_data *cd)
{
struct param_node *pos, *temp;
spin_lock(&cd->spinlock);
list_for_each_entry_safe(pos, temp, &cd->param_list, node) {
pt_debug(cd->dev, DL_INFO,
"%s: Parameter Restore List - remove 0x%02x\n",
__func__, pos->id);
list_del(&pos->node);
kfree(pos);
}
spin_unlock(&cd->spinlock);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_count_parameter_list
*
* SUMMARY: Count the items in the RAM parameter restor list
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_count_parameter_list(struct pt_core_data *cd)
{
struct param_node *pos, *temp;
int entries = 0;
spin_lock(&cd->spinlock);
list_for_each_entry_safe(pos, temp, &cd->param_list, node)
entries++;
spin_unlock(&cd->spinlock);
return entries;
}
#endif /* TTDL_DIAGNOSTICS */
/*******************************************************************************
* FUNCTION: request_exclusive
*
* SUMMARY: Request exclusive access to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *ownptr - pointer to device
* timeout_ms - Timeout value
******************************************************************************/
int request_exclusive(struct pt_core_data *cd, void *ownptr,
int timeout_ms)
{
int t = msecs_to_jiffies(timeout_ms);
bool with_timeout = (timeout_ms != 0);
pt_debug(cd->dev, DL_INFO, "%s: Attempt to Request EXCLUSIVE t=%d\n",
__func__, timeout_ms);
mutex_lock(&cd->system_lock);
if (!cd->exclusive_dev && cd->exclusive_waits == 0) {
cd->exclusive_dev = ownptr;
goto exit;
}
cd->exclusive_waits++;
wait:
mutex_unlock(&cd->system_lock);
if (with_timeout) {
t = wait_event_timeout(cd->wait_q, !cd->exclusive_dev, t);
if (IS_TMO(t)) {
pt_debug(cd->dev, DL_ERROR,
"%s: tmo waiting exclusive access\n", __func__);
return -ETIME;
}
} else {
wait_event(cd->wait_q, !cd->exclusive_dev);
}
mutex_lock(&cd->system_lock);
if (cd->exclusive_dev)
goto wait;
cd->exclusive_dev = ownptr;
cd->exclusive_waits--;
exit:
mutex_unlock(&cd->system_lock);
pt_debug(cd->dev, DL_DEBUG, "%s: request exclusive ok=%p\n",
__func__, ownptr);
return 0;
}
/*******************************************************************************
* FUNCTION: release_exclusive_
*
* SUMMARY: Release exclusive access to the DUT
*
* RETURN:
* 0 = success
*
* PARAMETERS:
* *cd - pointer to core data
* *ownptr - pointer to device
******************************************************************************/
static int release_exclusive_(struct pt_core_data *cd, void *ownptr)
{
pt_debug(cd->dev, DL_INFO, "%s: Attempt to Release EXCLUSIVE\n",
__func__);
if (cd->exclusive_dev != ownptr)
return -EINVAL;
pt_debug(cd->dev, DL_DEBUG, "%s: exclusive_dev %p freed\n",
__func__, cd->exclusive_dev);
cd->exclusive_dev = NULL;
wake_up(&cd->wait_q);
return 0;
}
/*******************************************************************************
* FUNCTION: release_exclusive
*
* SUMMARY: Protected wrapper to release_exclusive_()
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *ownptr - pointer to device
******************************************************************************/
int release_exclusive(struct pt_core_data *cd, void *ownptr)
{
int rc;
mutex_lock(&cd->system_lock);
rc = release_exclusive_(cd, ownptr);
mutex_unlock(&cd->system_lock);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_exec_cmd_
*
* SUMMARY: Send the HID command to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_cmd - pointer to the HID command to send
******************************************************************************/
static int pt_hid_exec_cmd_(struct pt_core_data *cd,
struct pt_hid_cmd *hid_cmd)
{
int rc = 0;
u8 *cmd;
u16 cmd_length;
u8 cmd_offset = 0;
cmd_length = 2 /* command register */
+ 2 /* command */
+ (hid_cmd->report_id >= 0XF ? 1 : 0) /* Report ID */
+ (hid_cmd->has_data_register ? 2 : 0) /* Data register */
+ hid_cmd->write_length; /* Data length */
if (cmd_length < 4 || cmd_length > PT_MAX_PIP1_MSG_SIZE)
return -EPROTO;
cmd = kzalloc(cmd_length, GFP_KERNEL);
if (!cmd)
return -ENOMEM;
/* Set Command register */
memcpy(&cmd[cmd_offset], &cd->hid_desc.command_register,
sizeof(cd->hid_desc.command_register));
cmd_offset += sizeof(cd->hid_desc.command_register);
/* Set Command */
SET_CMD_REPORT_TYPE(cmd[cmd_offset], hid_cmd->report_type);
if (hid_cmd->report_id >= 0XF)
SET_CMD_REPORT_ID(cmd[cmd_offset], 0xF);
else
SET_CMD_REPORT_ID(cmd[cmd_offset], hid_cmd->report_id);
cmd_offset++;
SET_CMD_OPCODE(cmd[cmd_offset], hid_cmd->opcode);
cmd_offset++;
if (hid_cmd->report_id >= 0XF) {
cmd[cmd_offset] = hid_cmd->report_id;
cmd_offset++;
}
/* Set Data register */
if (hid_cmd->has_data_register) {
memcpy(&cmd[cmd_offset], &cd->hid_desc.data_register,
sizeof(cd->hid_desc.data_register));
cmd_offset += sizeof(cd->hid_desc.data_register);
}
/* Set Data */
if (hid_cmd->write_length && hid_cmd->write_buf) {
memcpy(&cmd[cmd_offset], hid_cmd->write_buf,
hid_cmd->write_length);
cmd_offset += hid_cmd->write_length;
}
pt_debug(cd->dev, DL_INFO,
">>> %s: Write Buffer Size[%d] Cmd[0x%02X]\n",
__func__, cmd_length, hid_cmd->report_id);
pt_pr_buf(cd->dev, DL_DEBUG, cmd, cmd_length, ">>> CMD");
rc = pt_adap_write_read_specific(cd, cmd_length, cmd,
hid_cmd->read_buf);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: Fail pt_adap_transfer\n", __func__);
kfree(cmd);
return rc;
}
#ifdef TTDL_DIAGNOSTICS
/*******************************************************************************
* FUNCTION: pt_toggle_err_gpio
*
* SUMMARY: Toggles the pre-defined error GPIO
*
* RETURN: n/a
*
* PARAMETERS:
* *cd - pointer to core data
* type - type of err that occurred
******************************************************************************/
void pt_toggle_err_gpio(struct pt_core_data *cd, u8 type)
{
pt_debug(cd->dev, DL_DEBUG, "%s called with type = %d\n",
__func__, type);
if (cd->err_gpio && type == cd->err_gpio_type) {
pt_debug(cd->dev, DL_WARN, "%s: Toggle ERR GPIO\n", __func__);
gpio_direction_output(cd->err_gpio,
!gpio_get_value(cd->err_gpio));
}
}
/*******************************************************************************
* FUNCTION: _pt_request_toggle_err_gpio
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request to toggle the err_gpio
*
* RETURN: n/a
*
* PARAMETERS:
* *cd - pointer to core data
* type - type of err that occurred
******************************************************************************/
void _pt_request_toggle_err_gpio(struct device *dev, u8 type)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
pt_toggle_err_gpio(cd, type);
}
#endif /* TTDL_DIAGNOSTICS */
/*******************************************************************************
* FUNCTION: pt_hid_exec_cmd_and_wait_
*
* SUMMARY: Send the HID command to the DUT and wait for the response
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_cmd - pointer to the HID command to send
******************************************************************************/
static int pt_hid_exec_cmd_and_wait_(struct pt_core_data *cd,
struct pt_hid_cmd *hid_cmd)
{
int rc = 0;
int t;
u16 timeout_ms;
int *cmd_state;
if (hid_cmd->reset_cmd)
cmd_state = &cd->hid_reset_cmd_state;
else
cmd_state = &cd->hid_cmd_state;
if (hid_cmd->wait_interrupt) {
mutex_lock(&cd->system_lock);
*cmd_state = 1;
mutex_unlock(&cd->system_lock);
}
rc = pt_hid_exec_cmd_(cd, hid_cmd);
if (rc) {
if (hid_cmd->wait_interrupt)
goto error;
goto exit;
}
if (!hid_cmd->wait_interrupt)
goto exit;
if (hid_cmd->timeout_ms)
timeout_ms = hid_cmd->timeout_ms;
else
timeout_ms = PT_HID_CMD_DEFAULT_TIMEOUT;
t = wait_event_timeout(cd->wait_q, (*cmd_state == 0),
msecs_to_jiffies(timeout_ms));
if (IS_TMO(t)) {
#ifdef TTDL_DIAGNOSTICS
cd->bus_transmit_error_count++;
pt_toggle_err_gpio(cd, PT_ERR_GPIO_I2C_TRANS);
#endif /* TTDL_DIAGNOSTICS */
pt_debug(cd->dev, DL_ERROR,
"%s: HID output cmd execution timed out\n",
__func__);
rc = -ETIME;
goto error;
}
goto exit;
error:
mutex_lock(&cd->system_lock);
*cmd_state = 0;
mutex_unlock(&cd->system_lock);
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_cmd_reset_
*
* SUMMARY: Send the HID RESET command to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_hid_cmd_reset_(struct pt_core_data *cd)
{
struct pt_hid_cmd hid_cmd = {
.opcode = HID_CMD_RESET,
.wait_interrupt = 1,
.reset_cmd = 1,
.timeout_ms = PT_HID_CMD_DEFAULT_TIMEOUT,
};
return pt_hid_exec_cmd_and_wait_(cd, &hid_cmd);
}
/*******************************************************************************
* FUNCTION: pt_hid_cmd_reset
*
* SUMMARY: Wrapper function for pt_hid_cmd_reset_ that guarantees exclusive
* access.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_hid_cmd_reset(struct pt_core_data *cd)
{
int rc = 0;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
pt_debug(cd->dev, DL_INFO, "%s: Send HID Reset command\n", __func__);
rc = pt_hid_cmd_reset_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_cmd_set_power_
*
* SUMMARY: Send hid cmd to set power state for the DUT and wait for response
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* power_state - power state to set(HID_POWER_ON/HID_POWER_SLEEP)
******************************************************************************/
static int pt_hid_cmd_set_power_(struct pt_core_data *cd,
u8 power_state)
{
int rc = 0;
struct pt_hid_cmd hid_cmd = {
.opcode = HID_CMD_SET_POWER,
.wait_interrupt = 1,
.timeout_ms = PT_HID_CMD_DEFAULT_TIMEOUT,
};
hid_cmd.power_state = power_state;
/* The chip won't give response if goes to Deep Standby */
if (power_state == HID_POWER_STANDBY) {
rc = pt_hid_exec_cmd_(cd, &hid_cmd);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: Failed to set power to state:%d\n",
__func__, power_state);
else
cd->fw_sys_mode_in_standby_state = true;
return rc;
}
cd->fw_sys_mode_in_standby_state = false;
rc = pt_hid_exec_cmd_and_wait_(cd, &hid_cmd);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Failed to set power to state:%d\n",
__func__, power_state);
return rc;
}
/* validate */
if ((cd->response_buf[2] != HID_RESPONSE_REPORT_ID)
|| ((cd->response_buf[3] & 0x3) != power_state)
|| ((cd->response_buf[4] & 0xF) != HID_CMD_SET_POWER))
rc = -EINVAL;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_cmd_set_power
*
* SUMMARY: Wrapper function for pt_hid_cmd_set_power_ that guarantees
* exclusive access.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* power_state - power state to set(HID_POWER_ON/HID_POWER_SLEEP)
******************************************************************************/
static int pt_hid_cmd_set_power(struct pt_core_data *cd,
u8 power_state)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_cmd_set_power_(cd, power_state);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
static const u16 crc_table[16] = {
0x0000, 0x1021, 0x2042, 0x3063,
0x4084, 0x50a5, 0x60c6, 0x70e7,
0x8108, 0x9129, 0xa14a, 0xb16b,
0xc18c, 0xd1ad, 0xe1ce, 0xf1ef,
};
/*******************************************************************************
* FUNCTION: _pt_compute_crc
*
* SUMMARY: Calculate CRC by CRC table.
*
* RETURN:
* CRC calculation result
*
* PARAMETERS:
* *buf - pointer to the data array to be calculated
* size - size of data array
******************************************************************************/
static u16 _pt_compute_crc(u8 *buf, u32 size)
{
u16 remainder = 0xFFFF;
u16 xor_mask = 0x0000;
u32 index;
u32 byte_value;
u32 table_index;
u32 crc_bit_width = sizeof(u16) * 8;
/* Divide the message by polynomial, via the table. */
for (index = 0; index < size; index++) {
byte_value = buf[index];
table_index = ((byte_value >> 4) & 0x0F)
^ (remainder >> (crc_bit_width - 4));
remainder = crc_table[table_index] ^ (remainder << 4);
table_index = (byte_value & 0x0F)
^ (remainder >> (crc_bit_width - 4));
remainder = crc_table[table_index] ^ (remainder << 4);
}
/* Perform the final remainder CRC. */
return remainder ^ xor_mask;
}
u16 ccitt_Table[] = {
0x0000, 0x1021, 0x2042, 0x3063, 0x4084, 0x50A5, 0x60C6, 0x70E7,
0x8108, 0x9129, 0xA14A, 0xB16B, 0xC18C, 0xD1AD, 0xE1CE, 0xF1EF,
0x1231, 0x0210, 0x3273, 0x2252, 0x52B5, 0x4294, 0x72F7, 0x62D6,
0x9339, 0x8318, 0xB37B, 0xA35A, 0xD3BD, 0xC39C, 0xF3FF, 0xE3DE,
0x2462, 0x3443, 0x0420, 0x1401, 0x64E6, 0x74C7, 0x44A4, 0x5485,
0xA56A, 0xB54B, 0x8528, 0x9509, 0xE5EE, 0xF5CF, 0xC5AC, 0xD58D,
0x3653, 0x2672, 0x1611, 0x0630, 0x76D7, 0x66F6, 0x5695, 0x46B4,
0xB75B, 0xA77A, 0x9719, 0x8738, 0xF7DF, 0xE7FE, 0xD79D, 0xC7BC,
0x48C4, 0x58E5, 0x6886, 0x78A7, 0x0840, 0x1861, 0x2802, 0x3823,
0xC9CC, 0xD9ED, 0xE98E, 0xF9AF, 0x8948, 0x9969, 0xA90A, 0xB92B,
0x5AF5, 0x4AD4, 0x7AB7, 0x6A96, 0x1A71, 0x0A50, 0x3A33, 0x2A12,
0xDBFD, 0xCBDC, 0xFBBF, 0xEB9E, 0x9B79, 0x8B58, 0xBB3B, 0xAB1A,
0x6CA6, 0x7C87, 0x4CE4, 0x5CC5, 0x2C22, 0x3C03, 0x0C60, 0x1C41,
0xEDAE, 0xFD8F, 0xCDEC, 0xDDCD, 0xAD2A, 0xBD0B, 0x8D68, 0x9D49,
0x7E97, 0x6EB6, 0x5ED5, 0x4EF4, 0x3E13, 0x2E32, 0x1E51, 0x0E70,
0xFF9F, 0xEFBE, 0xDFDD, 0xCFFC, 0xBF1B, 0xAF3A, 0x9F59, 0x8F78,
0x9188, 0x81A9, 0xB1CA, 0xA1EB, 0xD10C, 0xC12D, 0xF14E, 0xE16F,
0x1080, 0x00A1, 0x30C2, 0x20E3, 0x5004, 0x4025, 0x7046, 0x6067,
0x83B9, 0x9398, 0xA3FB, 0xB3DA, 0xC33D, 0xD31C, 0xE37F, 0xF35E,
0x02B1, 0x1290, 0x22F3, 0x32D2, 0x4235, 0x5214, 0x6277, 0x7256,
0xB5EA, 0xA5CB, 0x95A8, 0x8589, 0xF56E, 0xE54F, 0xD52C, 0xC50D,
0x34E2, 0x24C3, 0x14A0, 0x0481, 0x7466, 0x6447, 0x5424, 0x4405,
0xA7DB, 0xB7FA, 0x8799, 0x97B8, 0xE75F, 0xF77E, 0xC71D, 0xD73C,
0x26D3, 0x36F2, 0x0691, 0x16B0, 0x6657, 0x7676, 0x4615, 0x5634,
0xD94C, 0xC96D, 0xF90E, 0xE92F, 0x99C8, 0x89E9, 0xB98A, 0xA9AB,
0x5844, 0x4865, 0x7806, 0x6827, 0x18C0, 0x08E1, 0x3882, 0x28A3,
0xCB7D, 0xDB5C, 0xEB3F, 0xFB1E, 0x8BF9, 0x9BD8, 0xABBB, 0xBB9A,
0x4A75, 0x5A54, 0x6A37, 0x7A16, 0x0AF1, 0x1AD0, 0x2AB3, 0x3A92,
0xFD2E, 0xED0F, 0xDD6C, 0xCD4D, 0xBDAA, 0xAD8B, 0x9DE8, 0x8DC9,
0x7C26, 0x6C07, 0x5C64, 0x4C45, 0x3CA2, 0x2C83, 0x1CE0, 0x0CC1,
0xEF1F, 0xFF3E, 0xCF5D, 0xDF7C, 0xAF9B, 0xBFBA, 0x8FD9, 0x9FF8,
0x6E17, 0x7E36, 0x4E55, 0x5E74, 0x2E93, 0x3EB2, 0x0ED1, 0x1EF0,
};
/*******************************************************************************
* FUNCTION: crc_ccitt_calculate
*
* SUMMARY: Calculate CRC with ccitt standard by CRC table.
*
* RETURN:
* CRC calculation result
*
* PARAMETERS:
* *q - pointer to the data array to be calculated
* len - size of data array
******************************************************************************/
static unsigned short crc_ccitt_calculate(unsigned char *q, int len)
{
unsigned short crc = 0xffff;
while (len-- > 0)
crc = ccitt_Table[(crc >> 8 ^ *q++) & 0xff] ^ (crc << 8);
return crc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_cmd_calculate_crc
*
* SUMMARY: Calculate the CRC of a command packet
*
* RETURN: void
*
* PARAMETERS:
* *cmd - pointer to command data
* extra_bytes - Extra bytes included in command length
******************************************************************************/
static void pt_pip2_cmd_calculate_crc(struct pip2_cmd_structure *cmd,
u8 extra_bytes)
{
u8 buf[PT_MAX_PIP2_MSG_SIZE + 1] = {0};
unsigned short crc;
buf[0] = cmd->len & 0xff;
buf[1] = (cmd->len & 0xff00) >> 8;
buf[2] = cmd->seq;
buf[3] = cmd->id;
memcpy(&buf[4], cmd->data, cmd->len - extra_bytes);
/* Calculate the CRC for the first 4 bytes above and the data payload */
crc = crc_ccitt_calculate(buf, 4 + (cmd->len - extra_bytes));
cmd->crc[0] = (crc & 0xff00) >> 8;
cmd->crc[1] = (crc & 0xff);
}
/*******************************************************************************
* FUNCTION: pt_pip2_get_next_cmd_seq
*
* SUMMARY: Gets the next sequence number for a PIP2 command. The sequence
* number is a 3 bit value (bits [0-2]) but because TTDL will always have
* the TAG bit set (bit 3), the counter starts at 0x08 and goes to 0x0F.
* If the "force_pip2_seq" holds a valid seq value (0x08-0x0F) then do not
* increment, just use the forced value.
*
* RETURN: Next command sequence number [0x08-0x0F]
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static u8 pt_pip2_get_next_cmd_seq(struct pt_core_data *cd)
{
#ifdef TTDL_DIAGNOSTICS
if (cd->force_pip2_seq <= 0x07) {
cd->pip2_cmd_tag_seq++;
if (cd->pip2_cmd_tag_seq > 0x0F)
cd->pip2_cmd_tag_seq = 0x08;
} else {
cd->pip2_cmd_tag_seq = cd->force_pip2_seq;
}
#else
cd->pip2_cmd_tag_seq++;
if (cd->pip2_cmd_tag_seq > 0x0F)
cd->pip2_cmd_tag_seq = 0x08;
#endif
return cd->pip2_cmd_tag_seq;
}
/*
* Following macros are to define the response time (the interval between PIP2
* command finishes sending and INT pin falls). The unit is in microsecond.
* It has different time settings between the solution GPIO polling and Bus
* polling due to the considration for system load.
*/
#ifdef PT_POLL_RESP_BY_BUS
#define POLL_RETRY_DEFAULT_INTERVAL 50
#define PIP2_RESP_DEFAULT_TIME_MIN 50
#define PIP2_RESP_DEFAULT_TIME_MAX (PT_PIP_CMD_DEFAULT_TIMEOUT * 1000)
#define PIP2_RESP_FILE_WRITE_TIME_MIN 220
#define PIP2_RESP_FILE_IOCTL_TIME_MAX (PT_PIP2_CMD_FILE_ERASE_TIMEOUT * 1000)
#else
#define POLL_RETRY_DEFAULT_INTERVAL 20
#define PIP2_RESP_DEFAULT_TIME_MIN 20
#define PIP2_RESP_DEFAULT_TIME_MAX (PT_PIP_CMD_DEFAULT_TIMEOUT * 1000)
#define PIP2_RESP_FILE_WRITE_TIME_MIN 20
#define PIP2_RESP_FILE_IOCTL_TIME_MAX (PT_PIP2_CMD_FILE_ERASE_TIMEOUT * 1000)
#endif
/*
* id: the command id defined in PIP2
* response_len: the (maximum) length of response.
* response_time_min: minimum response time in microsecond
* response_time_max: maximum response time in microsecond
*/
static const struct pip2_cmd_response_structure pip2_cmd_response[] = {
{.id = PIP2_CMD_ID_PING,
.response_len = 255,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_STATUS,
.response_len = PIP2_EXTRA_BYTES_NUM + 5,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_CTRL,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PT_PIP2_CMD_FILE_ERASE_TIMEOUT},
{.id = PIP2_CMD_ID_CONFIG,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_CLEAR,
.response_len = PIP2_EXTRA_BYTES_NUM + 0,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_RESET,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_VERSION,
.response_len = PIP2_EXTRA_BYTES_NUM + 23,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_FILE_OPEN,
.response_len = PIP2_EXTRA_BYTES_NUM + 2,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_FILE_CLOSE,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_FILE_READ,
.response_len = 255,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_FILE_WRITE,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_FILE_WRITE_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_FILE_IOCTL,
.response_len = PIP2_EXTRA_BYTES_NUM + 10,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_FILE_IOCTL_TIME_MAX},
{.id = PIP2_CMD_ID_FLASH_INFO,
.response_len = PIP2_EXTRA_BYTES_NUM + 17,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_EXECUTE,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_GET_LAST_ERRNO,
.response_len = PIP2_EXTRA_BYTES_NUM + 3,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_EXIT_HOST_MODE,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_READ_GPIO,
.response_len = PIP2_EXTRA_BYTES_NUM + 5,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_EXECUTE_SCAN,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_SET_PARAMETER,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_GET_PARAMETER,
.response_len = PIP2_EXTRA_BYTES_NUM + 7,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_SET_DDI_REG,
.response_len = PIP2_EXTRA_BYTES_NUM + 1,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_GET_DDI_REG,
.response_len = PIP2_EXTRA_BYTES_NUM + 249,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX},
{.id = PIP2_CMD_ID_END,
.response_len = 255,
.response_time_min = PIP2_RESP_DEFAULT_TIME_MIN,
.response_time_max = PIP2_RESP_DEFAULT_TIME_MAX}
};
/*******************************************************************************
* FUNCTION: pt_pip2_get_cmd_response_len
*
* SUMMARY: Gets the expected response length based on the command ID
*
* RETURN: Expected response length
*
* PARAMETERS:
* id - Command ID (-1 means input ID is not in list of PIP2 command)
******************************************************************************/
static int pt_pip2_get_cmd_response_len(u8 id)
{
const struct pip2_cmd_response_structure *p = pip2_cmd_response;
while ((p->id != id) && (p->id != PIP2_CMD_ID_END))
p++;
if (p->id != PIP2_CMD_ID_END)
return p->response_len;
else
return -EPERM;
}
/*******************************************************************************
* FUNCTION: pt_pip2_get_cmd_resp_time_min
*
* SUMMARY: Gets the minimum response time (the interval between PIP2 command
* finishes sending and INT pin falls) based on the command ID
*
* RETURN: Estimated minimum response time in microsecond
*
* PARAMETERS:
* id - Command ID
******************************************************************************/
static u32 pt_pip2_get_cmd_resp_time_min(u8 id)
{
const struct pip2_cmd_response_structure *p = pip2_cmd_response;
while ((p->id != id) && (p->id != PIP2_CMD_ID_END))
p++;
if (p->id != PIP2_CMD_ID_END)
return p->response_time_min;
else
return PIP2_RESP_DEFAULT_TIME_MIN;
}
/*******************************************************************************
* FUNCTION: pt_pip2_get_cmd_resp_time_max
*
* SUMMARY: Gets the maximum response time (the interval between PIP2 command
* finishes sending and INT pin falls) based on the command ID
*
* RETURN: Estimated maximum response time in microsecond
*
* PARAMETERS:
* id - Command ID
******************************************************************************/
static u32 pt_pip2_get_cmd_resp_time_max(u8 id)
{
const struct pip2_cmd_response_structure *p = pip2_cmd_response;
while ((p->id != id) && (p->id != PIP2_CMD_ID_END))
p++;
if (p->id != PIP2_CMD_ID_END)
return p->response_time_max;
else
return PIP2_RESP_DEFAULT_TIME_MAX;
}
/*******************************************************************************
* FUNCTION: pt_pip2_validate_response
*
* SUMMARY: Validate the response of PIP2 command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *pip2_cmd - pointer to PIP2 command to send
* *read_buf - pointer to response buffer
* actual_read_len - actual read length of the response
******************************************************************************/
static int pt_pip2_validate_response(struct pt_core_data *cd,
struct pip2_cmd_structure *pip2_cmd, u8 *read_buf,
u16 actual_read_len)
{
int rc = 0;
u8 response_seq = 0;
u8 reserved_bits = 0;
u8 cmd_id = 0;
u8 response_bit = 0;
unsigned short calc_crc = 0;
unsigned short resp_crc = 0;
/* Verify the length of response buffer */
if (actual_read_len < PT_MIN_PIP2_PACKET_SIZE) {
pt_debug(cd->dev, DL_ERROR,
"%s cmd[0x%02X] read length ERR: read_len = %d\n",
__func__, pip2_cmd->id, actual_read_len);
rc = -EINVAL;
goto exit;
}
/* Verify the CRC */
calc_crc = crc_ccitt_calculate(read_buf, actual_read_len - 2);
resp_crc = read_buf[actual_read_len - 2] << 8;
resp_crc |= read_buf[actual_read_len - 1];
if (resp_crc != calc_crc) {
pt_debug(cd->dev, DL_ERROR,
"%s: cmd[0x%02X] CRC ERR: calc=0x%04X rsp=0x%04X\n",
__func__, pip2_cmd->id, calc_crc, resp_crc);
#ifdef TTDL_DIAGNOSTICS
cd->pip2_crc_error_count++;
#endif /* TTDL_DIAGNOSTICS */
rc = -EINVAL;
goto exit;
}
/* Verify the response bit is set */
response_bit = read_buf[PIP2_RESP_REPORT_ID_OFFSET] & 0x80;
if (!response_bit) {
pt_debug(cd->dev, DL_ERROR,
"%s cmd[0x%02X] response bit ERR: response_bit = %d\n",
__func__, pip2_cmd->id, response_bit);
rc = -EINVAL;
goto exit;
}
/* Verify the command ID matches from command to response */
cmd_id = read_buf[PIP2_RESP_REPORT_ID_OFFSET] & 0x7F;
if (cmd_id != pip2_cmd->id) {
pt_debug(cd->dev, DL_ERROR,
"%s cmd[0x%02X] command ID ERR: cmd_id = 0x%02X\n",
__func__, pip2_cmd->id, cmd_id);
rc = -EINVAL;
goto exit;
}
/* Verify the SEQ number matches from command to response */
response_seq = read_buf[PIP2_RESP_SEQUENCE_OFFSET] & 0x0F;
if ((pip2_cmd->seq & 0x0F) != response_seq) {
pt_debug(cd->dev, DL_ERROR,
"%s cmd[0x%02X] send_seq = 0x%02X, resp_seq = 0x%02X\n",
__func__, pip2_cmd->id,
pip2_cmd->seq, response_seq);
rc = -EINVAL;
goto exit;
}
/* Verify the reserved bits are 0 */
reserved_bits = read_buf[PIP2_RESP_SEQUENCE_OFFSET] & 0xF0;
if (reserved_bits)
pt_debug(cd->dev, DL_WARN,
"%s cmd[0x%02X] reserved_bits = 0x%02X\n",
__func__, pip2_cmd->id, reserved_bits);
exit:
if (rc)
pt_pr_buf(cd->dev, DL_WARN, cd->input_buf, actual_read_len,
"PIP RSP:");
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_validate_bl_response
*
* SUMMARY: Validate the response of bootloader command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to hid output data structure
******************************************************************************/
static int pt_hid_output_validate_bl_response(
struct pt_core_data *cd,
struct pt_hid_output *hid_output)
{
u16 size;
u16 crc;
u8 status;
size = get_unaligned_le16(&cd->response_buf[0]);
if (hid_output->reset_expected && !size)
return 0;
if (cd->response_buf[PIP1_RESP_REPORT_ID_OFFSET]
!= PT_PIP_BL_RESPONSE_REPORT_ID) {
pt_debug(cd->dev, DL_ERROR,
"%s: BL output response, wrong report_id\n", __func__);
return -EPROTO;
}
if (cd->response_buf[4] != PIP1_BL_SOP) {
pt_debug(cd->dev, DL_ERROR,
"%s: BL output response, wrong SOP\n", __func__);
return -EPROTO;
}
if (cd->response_buf[size - 1] != PIP1_BL_EOP) {
pt_debug(cd->dev, DL_ERROR,
"%s: BL output response, wrong EOP\n", __func__);
return -EPROTO;
}
crc = _pt_compute_crc(&cd->response_buf[4], size - 7);
if (cd->response_buf[size - 3] != LOW_BYTE(crc)
|| cd->response_buf[size - 2] != HI_BYTE(crc)) {
pt_debug(cd->dev, DL_ERROR,
"%s: BL output response, wrong CRC 0x%X\n",
__func__, crc);
return -EPROTO;
}
status = cd->response_buf[5];
if (status) {
pt_debug(cd->dev, DL_ERROR,
"%s: BL output response, ERROR:%d\n",
__func__, status);
return -EPROTO;
}
return 0;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_validate_app_response
*
* SUMMARY: Validate the response of application command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to hid output data structure
******************************************************************************/
static int pt_hid_output_validate_app_response(
struct pt_core_data *cd,
struct pt_hid_output *hid_output)
{
int command_code;
u16 size;
size = get_unaligned_le16(&cd->response_buf[0]);
if (hid_output->reset_expected && !size)
return 0;
if (cd->response_buf[PIP1_RESP_REPORT_ID_OFFSET]
!= PT_PIP_NON_HID_RESPONSE_ID) {
pt_debug(cd->dev, DL_ERROR,
"%s: APP output response, wrong report_id\n", __func__);
return -EPROTO;
}
command_code = cd->response_buf[PIP1_RESP_COMMAND_ID_OFFSET]
& PIP1_RESP_COMMAND_ID_MASK;
if (command_code != hid_output->command_code) {
pt_debug(cd->dev, DL_ERROR,
"%s: APP output response, wrong command_code:%X\n",
__func__, command_code);
return -EPROTO;
}
return 0;
}
/*******************************************************************************
* FUNCTION: pt_check_set_parameter
*
* SUMMARY: Check command input and response for Set Parameter command.And
* store the parameter to the list for resume work if pass the check.
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to hid output data structure
* raw - flag to show if output cmd is user cmd(1:user cmd)
******************************************************************************/
static void pt_check_set_parameter(struct pt_core_data *cd,
struct pt_hid_output *hid_output, bool raw)
{
u8 *param_buf;
u32 param_value = 0;
u8 param_size;
u8 param_id;
int i = 0;
if (!(cd->cpdata->flags & PT_CORE_FLAG_RESTORE_PARAMETERS))
return;
/* Check command input for Set Parameter command */
if (raw && hid_output->length >= 10 && hid_output->length <= 13
&& !memcmp(&hid_output->write_buf[0],
&cd->hid_desc.output_register,
sizeof(cd->hid_desc.output_register))
&& hid_output->write_buf[4] ==
PT_PIP_NON_HID_COMMAND_ID
&& hid_output->write_buf[6] ==
PIP1_CMD_ID_SET_PARAM)
param_buf = &hid_output->write_buf[7];
else if (!raw && hid_output->cmd_type == PIP1_CMD_TYPE_FW
&& hid_output->command_code == PIP1_CMD_ID_SET_PARAM
&& hid_output->write_length >= 3
&& hid_output->write_length <= 6)
param_buf = &hid_output->write_buf[0];
else
return;
/* Get parameter ID, size and value */
param_id = param_buf[0];
param_size = param_buf[1];
if (param_size > 4) {
pt_debug(cd->dev, DL_ERROR,
"%s: Invalid parameter size\n", __func__);
return;
}
param_buf = ¶m_buf[2];
while (i < param_size)
param_value += *(param_buf++) << (8 * i++);
/* Check command response for Set Parameter command */
if (cd->response_buf[2] != PT_PIP_NON_HID_RESPONSE_ID
|| (cd->response_buf[4] &
PIP1_RESP_COMMAND_ID_MASK) !=
PIP1_CMD_ID_SET_PARAM
|| cd->response_buf[5] != param_id
|| cd->response_buf[6] != param_size) {
pt_debug(cd->dev, DL_ERROR,
"%s: Set Parameter command not successful\n",
__func__);
return;
}
pt_add_parameter(cd, param_id, param_value, param_size);
}
/*******************************************************************************
* FUNCTION: pt_check_command
*
* SUMMARY: Check the output command. The function pt_check_set_parameter() is
* called here to check output command and store parameter to the list.
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to hid output data structure
* raw - flag to show if output cmd is user cmd(1:user cmd)
******************************************************************************/
static void pt_check_command(struct pt_core_data *cd,
struct pt_hid_output *hid_output, bool raw)
{
pt_check_set_parameter(cd, hid_output, raw);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_validate_response
*
* SUMMARY: Validate the response of application or bootloader command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to hid output data structure
******************************************************************************/
static int pt_hid_output_validate_response(struct pt_core_data *cd,
struct pt_hid_output *hid_output)
{
if (hid_output->cmd_type == PIP1_CMD_TYPE_BL)
return pt_hid_output_validate_bl_response(cd, hid_output);
return pt_hid_output_validate_app_response(cd, hid_output);
}
/*******************************************************************************
* FUNCTION: pt_hid_send_output_user_
*
* SUMMARY: Blindly send user data to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to the command to send
******************************************************************************/
static int pt_hid_send_output_user_(struct pt_core_data *cd,
struct pt_hid_output *hid_output)
{
int rc = 0;
int cmd;
if (!hid_output->length || !hid_output->write_buf)
return -EINVAL;
if (cd->pip2_prot_active) {
cmd = hid_output->write_buf[PIP2_CMD_COMMAND_ID_OFFSET];
cmd &= PIP2_CMD_COMMAND_ID_MASK;
} else
cmd = hid_output->write_buf[PIP1_CMD_COMMAND_ID_OFFSET];
pt_debug(cd->dev, DL_INFO,
">>> %s: Write Buffer Size[%d] Cmd[0x%02X]\n",
__func__, hid_output->length, cmd);
pt_pr_buf(cd->dev, DL_DEBUG, hid_output->write_buf,
hid_output->length, ">>> User CMD");
rc = pt_adap_write_read_specific(cd, hid_output->length,
hid_output->write_buf, NULL);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: Fail pt_adap_transfer\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_send_output_user_and_wait_
*
* SUMMARY: Blindly send user data to the DUT and wait for the response.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to the command to send
******************************************************************************/
static int pt_hid_send_output_user_and_wait_(struct pt_core_data *cd,
struct pt_hid_output *hid_output)
{
int rc = 0;
int t;
mutex_lock(&cd->system_lock);
cd->hid_cmd_state = PIP1_CMD_ID_USER_CMD + 1;
mutex_unlock(&cd->system_lock);
rc = pt_hid_send_output_user_(cd, hid_output);
if (rc)
goto error;
t = wait_event_timeout(cd->wait_q, (cd->hid_cmd_state == 0),
msecs_to_jiffies(cd->pip_cmd_timeout));
if (IS_TMO(t)) {
#ifdef TTDL_DIAGNOSTICS
cd->bus_transmit_error_count++;
pt_toggle_err_gpio(cd, PT_ERR_GPIO_I2C_TRANS);
#endif /* TTDL_DIAGNOSTICS */
pt_debug(cd->dev, DL_ERROR,
"%s: HID output cmd execution timed out\n",
__func__);
rc = -ETIME;
goto error;
}
pt_check_command(cd, hid_output, true);
goto exit;
error:
mutex_lock(&cd->system_lock);
cd->hid_cmd_state = 0;
mutex_unlock(&cd->system_lock);
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_check_irq_asserted
*
* SUMMARY: Checks if the IRQ GPIO is asserted or not. There are times when
* the FW can hold the INT line low ~150us after the read is complete.
* NOTE: if irq_stat is not defined this function will return false
*
* RETURN:
* true = IRQ asserted
* false = IRQ not asserted
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static bool pt_check_irq_asserted(struct pt_core_data *cd)
{
#ifdef ENABLE_WORKAROUND_FOR_GLITCH_AFTER_BL_LAUNCH_APP
/*
* Workaround for FW defect, CDT165308
* bl_launch app creates a glitch in IRQ line
*/
if (cd->hid_cmd_state == PIP1_BL_CMD_ID_LAUNCH_APP + 1
&& cd->cpdata->irq_stat) {
/*
* in X1S panel and GC1546 panel, the width for the INT
* glitch is about 4us,the normal INT width of response
* will last more than 200us, so use 10us delay
* for distinguish the glitch the normal INT is enough.
*/
udelay(10);
}
#endif
if (cd->cpdata->irq_stat) {
if (cd->cpdata->irq_stat(cd->cpdata, cd->dev)
== PT_IRQ_ASSERTED_VALUE) {
/* Debounce to allow FW to release INT */
usleep_range(100, 200);
}
if (cd->cpdata->irq_stat(cd->cpdata, cd->dev)
== PT_IRQ_ASSERTED_VALUE)
return true;
else
return false;
}
return true;
}
/*******************************************************************************
* FUNCTION: pt_flush_bus
*
* SUMMARY: Force flushing the bus by reading len bytes or forced 255 bytes
* Used if IRQ is found to be stuck low
*
* RETURN: Length of bytes read from bus
*
* PARAMETERS:
* *cd - pointer to core data
* flush_type - type of flush
* - PT_FLUSH_BUS_BASED_ON_LEN (two reads)
* - PT_FLUSH_BUS_FULL_256_READ
* *read_buf - pointer to store read data
******************************************************************************/
static ssize_t pt_flush_bus(struct pt_core_data *cd,
u8 flush_type, u8 *read_buf)
{
u8 buf[PT_MAX_PIP2_MSG_SIZE];
u16 pip_len;
int bytes_read;
int rc = 0;
if (flush_type == PT_FLUSH_BUS_BASED_ON_LEN) {
rc = pt_adap_read_default(cd, buf, 2);
if (rc) {
bytes_read = 0;
goto exit;
}
pip_len = get_unaligned_le16(&buf[0]);
if (pip_len == 2 || pip_len >= PT_PIP_1P7_EMPTY_BUF) {
#ifdef TTDL_DIAGNOSTICS
pt_toggle_err_gpio(cd, PT_ERR_GPIO_EMPTY_PACKET);
#endif
bytes_read = 2;
pt_debug(cd->dev, DL_INFO,
"%s: Empty buf detected - len=0x%04X\n",
__func__, pip_len);
} else if (pip_len == 0) {
bytes_read = 0;
pt_debug(cd->dev, DL_INFO,
"%s: Sentinel detected\n", __func__);
} else if (pip_len > PT_MAX_PIP2_MSG_SIZE) {
pt_debug(cd->dev, DL_ERROR,
"%s: Illegal len=0x%04x, force %d byte read\n",
__func__, pip_len, PT_MAX_PIP2_MSG_SIZE);
rc = pt_adap_read_default(cd, buf,
PT_MAX_PIP2_MSG_SIZE);
if (!rc)
bytes_read = PT_MAX_PIP2_MSG_SIZE;
else
bytes_read = 0;
} else {
pt_debug(cd->dev, DL_INFO,
"%s: Flush read of %d bytes...\n",
__func__, pip_len);
rc = pt_adap_read_default(cd, buf, pip_len);
if (!rc)
bytes_read = pip_len;
else
bytes_read = 0;
}
} else {
pt_debug(cd->dev, DL_INFO,
"%s: Forced flush of max %d bytes...\n",
__func__, PT_MAX_PIP2_MSG_SIZE);
rc = pt_adap_read_default(cd, buf, PT_MAX_PIP2_MSG_SIZE);
if (!rc)
bytes_read = PT_MAX_PIP2_MSG_SIZE;
else
bytes_read = 0;
}
if (read_buf && (bytes_read > 3))
memcpy(read_buf, buf, bytes_read);
exit:
return bytes_read;
}
/*******************************************************************************
* FUNCTION: pt_flush_bus_if_irq_asserted
*
* SUMMARY: This function will flush the active bus if the INT is found to be
* asserted.
*
* RETURN: bytes cleared from bus
*
* PARAMETERS:
* *cd - pointer the core data structure
* flush_type - type of flush
* - PT_FLUSH_BUS_BASED_ON_LEN
* - PT_FLUSH_BUS_FULL_256_READ
******************************************************************************/
static int pt_flush_bus_if_irq_asserted(struct pt_core_data *cd, u8 flush_type)
{
int count = 0;
int bytes_read = 0;
while (pt_check_irq_asserted(cd) && count < 5) {
count++;
bytes_read = pt_flush_bus(cd, flush_type, NULL);
if (bytes_read) {
pt_debug(cd->dev, DL_WARN,
"%s: Cleared %d bytes off bus\n",
__func__, bytes_read);
}
}
if (pt_check_irq_asserted(cd)) {
pt_debug(cd->dev, DL_ERROR,
"%s: IRQ still asserted, %d bytes read\n",
__func__, bytes_read);
} else {
pt_debug(cd->dev, DL_INFO,
"%s: IRQ cleared, %d bytes read\n",
__func__, bytes_read);
}
return bytes_read;
}
/*******************************************************************************
* FUNCTION: pt_hid_send_output_
*
* SUMMARY: Send a touch application command to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to the command to send
******************************************************************************/
static int pt_hid_send_output_(struct pt_core_data *cd,
struct pt_hid_output *hid_output)
{
int rc = 0;
u8 *cmd;
u16 length;
u16 crc;
u8 report_id;
u8 cmd_offset = 0;
u8 cmd_allocated = 0;
switch (hid_output->cmd_type) {
case PIP1_CMD_TYPE_FW:
report_id = PT_PIP_NON_HID_COMMAND_ID;
length = 5;
break;
case PIP1_CMD_TYPE_BL:
report_id = PT_PIP_BL_COMMAND_REPORT_ID;
length = 11 /* 5 + SOP + LEN(2) + CRC(2) + EOP */;
break;
default:
return -EINVAL;
}
length += hid_output->write_length;
if (length + 2 > PT_PREALLOCATED_CMD_BUFFER) {
cmd = kzalloc(length + 2, GFP_KERNEL);
if (!cmd)
return -ENOMEM;
cmd_allocated = 1;
} else {
cmd = cd->cmd_buf;
}
/* Set Output register */
memcpy(&cmd[cmd_offset], &cd->hid_desc.output_register,
sizeof(cd->hid_desc.output_register));
cmd_offset += sizeof(cd->hid_desc.output_register);
cmd[cmd_offset++] = LOW_BYTE(length);
cmd[cmd_offset++] = HI_BYTE(length);
cmd[cmd_offset++] = report_id;
cmd[cmd_offset++] = 0x0; /* reserved */
if (hid_output->cmd_type == PIP1_CMD_TYPE_BL)
cmd[cmd_offset++] = PIP1_BL_SOP;
cmd[cmd_offset++] = hid_output->command_code;
/* Set Data Length for bootloader */
if (hid_output->cmd_type == PIP1_CMD_TYPE_BL) {
cmd[cmd_offset++] = LOW_BYTE(hid_output->write_length);
cmd[cmd_offset++] = HI_BYTE(hid_output->write_length);
}
/* Set Data */
if (hid_output->write_length && hid_output->write_buf) {
memcpy(&cmd[cmd_offset], hid_output->write_buf,
hid_output->write_length);
cmd_offset += hid_output->write_length;
}
if (hid_output->cmd_type == PIP1_CMD_TYPE_BL) {
crc = _pt_compute_crc(&cmd[6],
hid_output->write_length + 4);
cmd[cmd_offset++] = LOW_BYTE(crc);
cmd[cmd_offset++] = HI_BYTE(crc);
cmd[cmd_offset++] = PIP1_BL_EOP;
}
pt_debug(cd->dev, DL_INFO,
">>> %s: Write Buffer Size[%d] Cmd[0x%02X]\n",
__func__, length + 2, hid_output->command_code);
pt_pr_buf(cd->dev, DL_DEBUG, cmd, length + 2, ">>> CMD");
rc = pt_adap_write_read_specific(cd, length + 2, cmd, NULL);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: Fail pt_adap_transfer rc=%d\n", __func__, rc);
if (cmd_allocated)
kfree(cmd);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip1_send_output_and_wait_
*
* SUMMARY: Send valid PIP1 command to the DUT and wait for the response.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hid_output - pointer to the command to send
******************************************************************************/
static int pt_pip1_send_output_and_wait_(struct pt_core_data *cd,
struct pt_hid_output *hid_output)
{
int rc = 0;
int t;
u16 timeout_ms;
mutex_lock(&cd->system_lock);
cd->hid_cmd_state = hid_output->command_code + 1;
mutex_unlock(&cd->system_lock);
if (hid_output->timeout_ms)
timeout_ms = hid_output->timeout_ms;
else
timeout_ms = PT_PIP1_CMD_DEFAULT_TIMEOUT;
rc = pt_hid_send_output_(cd, hid_output);
if (rc)
goto error;
t = wait_event_timeout(cd->wait_q, (cd->hid_cmd_state == 0),
msecs_to_jiffies(timeout_ms));
if (IS_TMO(t)) {
#ifdef TTDL_DIAGNOSTICS
cd->bus_transmit_error_count++;
pt_toggle_err_gpio(cd, PT_ERR_GPIO_I2C_TRANS);
#endif /* TTDL_DIAGNOSTICS */
pt_debug(cd->dev, DL_ERROR,
"%s: HID output cmd execution timed out (%dms)\n",
__func__, timeout_ms);
rc = -ETIME;
goto error;
}
if (!hid_output->novalidate)
rc = pt_hid_output_validate_response(cd, hid_output);
pt_check_command(cd, hid_output, false);
goto exit;
error:
mutex_lock(&cd->system_lock);
cd->hid_cmd_state = 0;
mutex_unlock(&cd->system_lock);
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_user_cmd_
*
* SUMMARY: Load the write buffer into a HID structure and send it as a HID cmd
* to the DUT waiting for the response and loading it into the read buffer
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* read_len - expected read length of the response
* *read_buf - pointer to where the response will be loaded
* write_len - length of the write buffer
* *write_buf - pointer to the write buffer
* *actual_read_len - pointer to the actual amount of data read back
******************************************************************************/
static int pt_hid_output_user_cmd_(struct pt_core_data *cd,
u16 read_len, u8 *read_buf, u16 write_len, u8 *write_buf,
u16 *actual_read_len)
{
int rc = 0;
u16 size;
struct pt_hid_output hid_output = {
.length = write_len,
.write_buf = write_buf,
};
#ifdef TTHE_TUNER_SUPPORT
if (!cd->pip2_send_user_cmd) {
int command_code = 0;
int len;
/* Print up to cmd ID */
len = PIP1_CMD_COMMAND_ID_OFFSET + 1;
if (write_len < len)
len = write_len;
else
command_code = write_buf[PIP1_CMD_COMMAND_ID_OFFSET]
& PIP1_CMD_COMMAND_ID_MASK;
/* Don't print EXEC_PANEL_SCAN & RETRIEVE_PANEL_SCAN commands */
if (command_code != PIP1_CMD_ID_EXEC_PANEL_SCAN &&
command_code != PIP1_CMD_ID_RETRIEVE_PANEL_SCAN)
tthe_print(cd, write_buf, len, "CMD=");
}
#endif
rc = pt_hid_send_output_user_and_wait_(cd, &hid_output);
if (rc)
return rc;
/* Get the response size from the first 2 bytes in the response */
size = get_unaligned_le16(&cd->response_buf[0]);
/* Ensure size is not greater than max buffer size */
if (size > PT_MAX_PIP2_MSG_SIZE)
size = PT_MAX_PIP2_MSG_SIZE;
/* Minimum size to read is the 2 byte len field */
if (size == 0)
size = 2;
if (size > read_len) {
pt_debug(cd->dev, DL_ERROR,
"%s: PIP2 len field=%d, requested read_len=%d\n",
__func__, size, read_len);
*actual_read_len = 0;
return -EIO;
}
memcpy(read_buf, cd->response_buf, size);
*actual_read_len = size;
return 0;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_user_cmd
*
* SUMMARY: Protected call to pt_hid_output_user_cmd_ by exclusive access to
* the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* read_len - length of data to read
* *read_buf - pointer to store read data
* write_len - length of data to write
* *write_buf - pointer to buffer to write
* *actual_read_len - pointer to store data length actually read
******************************************************************************/
static int pt_hid_output_user_cmd(struct pt_core_data *cd,
u16 read_len, u8 *read_buf, u16 write_len, u8 *write_buf,
u16 *actual_read_len)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_user_cmd_(cd, read_len, read_buf,
write_len, write_buf, actual_read_len);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip2_send_cmd
*
* SUMMARY: Writes a PIP2 command packet to DUT, then waits for the
* interrupt and reads response data to read_buf
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to run in protected mode
* id - ID of PIP command
* *data - pointer to PIP data payload
* report_body_len - report length
* *read_buf - pointer to response buffer
* *actual_read_len - pointer to response buffer length
******************************************************************************/
static int _pt_request_pip2_send_cmd(struct device *dev,
int protect, u8 id, u8 *data, u16 report_body_len, u8 *read_buf,
u16 *actual_read_len)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pip2_cmd_structure pip2_cmd;
int rc = 0;
u16 i = 0;
u16 j = 0;
u16 write_len;
u8 *write_buf = NULL;
u16 read_len;
u8 extra_bytes;
if (report_body_len > 247)
return -EPROTO;
memset(&pip2_cmd, 0, sizeof(pip2_cmd));
/* Hard coded register for PIP2.x */
pip2_cmd.reg[0] = 0x01;
pip2_cmd.reg[1] = 0x01;
/*
* For PIP2.1+ the length field value includes itself:
* ADD 6: 2 (LEN) + 1 (SEQ) + 1 (REPORT ID) + 2 (CRC)
*
* The overall write length must include only the register:
* ADD 2: 2 (Register)
*/
extra_bytes = 6;
write_len = 2;
/* PIP2 the CMD ID is a 7bit field */
if (id > PIP2_CMD_ID_END) {
pt_debug(dev, DL_WARN, "%s: Invalid PIP2 CMD ID 0x%02X\n",
__func__, id);
rc = -EINVAL;
goto exit;
}
pip2_cmd.len = report_body_len + extra_bytes;
pip2_cmd.id = id & PIP2_CMD_COMMAND_ID_MASK;
pip2_cmd.seq = pt_pip2_get_next_cmd_seq(cd);
pip2_cmd.data = data;
pt_pip2_cmd_calculate_crc(&pip2_cmd, extra_bytes);
/* Add the command length to the extra bytes based on PIP version */
write_len += pip2_cmd.len;
pt_debug(dev, DL_INFO, "%s Length Field: %d, Write Len: %d",
__func__, pip2_cmd.len, write_len);
write_buf = kzalloc(write_len, GFP_KERNEL);
if (write_buf == NULL) {
rc = -ENOMEM;
goto exit;
}
write_buf[i++] = pip2_cmd.reg[0];
write_buf[i++] = pip2_cmd.reg[1];
write_buf[i++] = pip2_cmd.len & 0xff;
write_buf[i++] = (pip2_cmd.len & 0xff00) >> 8;
write_buf[i++] = pip2_cmd.seq;
write_buf[i++] = pip2_cmd.id;
for (j = i; j < i + pip2_cmd.len - extra_bytes; j++)
write_buf[j] = pip2_cmd.data[j-i];
write_buf[j++] = pip2_cmd.crc[0];
write_buf[j++] = pip2_cmd.crc[1];
read_len = pt_pip2_get_cmd_response_len(pip2_cmd.id);
if (read_len < 0)
read_len = 255;
pt_debug(dev, DL_INFO,
"%s cmd_id[0x%02X] expected response length:%d ",
__func__, pip2_cmd.id, read_len);
/*
* All PIP2 commands come through this function.
* Set flag for PIP2.x interface to allow response parsing to know
* how to decode the protocol header.
*/
mutex_lock(&cd->system_lock);
cd->pip2_prot_active = true;
cd->pip2_send_user_cmd = true;
mutex_unlock(&cd->system_lock);
if (protect == PT_CORE_CMD_PROTECTED)
rc = pt_hid_output_user_cmd(cd, read_len, read_buf,
write_len, write_buf, actual_read_len);
else {
rc = pt_hid_output_user_cmd_(cd, read_len, read_buf,
write_len, write_buf, actual_read_len);
}
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: nonhid_cmd->user_cmd() Error = %d\n",
__func__, rc);
goto exit;
}
rc = pt_pip2_validate_response(cd, &pip2_cmd, read_buf,
*actual_read_len);
exit:
mutex_lock(&cd->system_lock);
cd->pip2_prot_active = false;
cd->pip2_send_user_cmd = false;
mutex_unlock(&cd->system_lock);
kfree(write_buf);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_send_cmd_no_int
*
* SUMMARY: Writes a PIP2 command packet to DUT, then poll the response and
* reads response data to read_buf if response is available.
*
* NOTE:
* Interrupt MUST be disabled before to call this function.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to run in protected mode
* id - ID of PIP command
* *data - pointer to PIP data payload
* report_body_len - report length
* *read_buf - pointer to response buffer
* *actual_read_len - pointer to response buffer length
******************************************************************************/
static int _pt_pip2_send_cmd_no_int(struct device *dev,
int protect, u8 id, u8 *data, u16 report_body_len, u8 *read_buf,
u16 *actual_read_len)
{
int max_retry = 0;
int retry = 0;
int rc = 0;
u16 i = 0;
u16 j = 0;
u16 write_len;
u8 *write_buf = NULL;
u16 read_len;
u16 size = 0;
u8 response_seq = 0;
u8 extra_bytes;
u32 retry_interval = 0;
u32 retry_total_time = 0;
u32 resp_time_min = pt_pip2_get_cmd_resp_time_min(id);
u32 resp_time_max = pt_pip2_get_cmd_resp_time_max(id);
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pip2_cmd_structure pip2_cmd;
if (report_body_len > 247)
return -EPROTO;
if (protect == PT_CORE_CMD_PROTECTED) {
rc = request_exclusive(cd,
cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
}
memset(&pip2_cmd, 0, sizeof(pip2_cmd));
/* Hard coded register for PIP2.x */
pip2_cmd.reg[0] = 0x01;
pip2_cmd.reg[1] = 0x01;
/*
* For PIP2.1+ the length field value includes itself:
* ADD 6: 2 (LEN) + 1 (SEQ) + 1 (REPORT ID) + 2 (CRC)
*
* The overall write length must include only the register:
* ADD 2: 2 (Register)
*/
extra_bytes = 6;
write_len = 2;
pip2_cmd.len = report_body_len + extra_bytes;
pip2_cmd.id = id;
pip2_cmd.seq = pt_pip2_get_next_cmd_seq(cd);
pip2_cmd.data = data;
pt_pip2_cmd_calculate_crc(&pip2_cmd, extra_bytes);
/* Add the command length to the extra bytes based on PIP version */
write_len += pip2_cmd.len;
write_buf = kzalloc(write_len, GFP_KERNEL);
if (write_buf == NULL) {
rc = -ENOMEM;
goto exit;
}
write_buf[i++] = pip2_cmd.reg[0];
write_buf[i++] = pip2_cmd.reg[1];
write_buf[i++] = pip2_cmd.len & 0xff;
write_buf[i++] = (pip2_cmd.len & 0xff00) >> 8;
write_buf[i++] = pip2_cmd.seq;
write_buf[i++] = pip2_cmd.id;
for (j = i; j < i + pip2_cmd.len - extra_bytes; j++)
write_buf[j] = pip2_cmd.data[j-i];
write_buf[j++] = pip2_cmd.crc[0];
write_buf[j++] = pip2_cmd.crc[1];
read_len = pt_pip2_get_cmd_response_len(pip2_cmd.id);
if (read_len < 0)
read_len = 255;
pt_debug(dev, DL_INFO,
"%s: ATM - cmd_id[0x%02X] expected response length:%d ",
__func__, pip2_cmd.id, read_len);
pt_pr_buf(cd->dev, DL_DEBUG, write_buf, write_len, ">>> NO_INT CMD");
rc = pt_adap_write_read_specific(cd, write_len, write_buf, NULL);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: SPI write Error = %d\n",
__func__, rc);
goto exit;
}
#ifdef PT_POLL_RESP_BY_BUS
/*
* Frequent bus read can increase system load obviously. The expected
* first bus read should be valid and timely. The tollerance for
* usleep_range should be limited. The minimum response delay (between
* command finishes sending and INT pin falls) is less than 50
* microseconds. So the 10 microseconds should be maximum tollerance
* with the consideration that the unit to calculate the response delay
* is 10 microseconds and more precise is not necessary. Every
* additional 10 microseconds only contribute less than 3 milliseconds
* for whole BL.
*/
usleep_range(resp_time_min, resp_time_min+10);
max_retry = resp_time_max / POLL_RETRY_DEFAULT_INTERVAL;
while ((retry < max_retry) && (retry_total_time < resp_time_max)) {
rc = pt_adap_read_default(cd, read_buf, read_len);
if (rc) {
pt_debug(dev, DL_ERROR, "%s: SPI read Error = %d\n",
__func__, rc);
break;
}
response_seq = read_buf[PIP2_RESP_SEQUENCE_OFFSET];
size = get_unaligned_le16(&read_buf[0]);
if ((size <= read_len) &&
(size >= PIP2_EXTRA_BYTES_NUM) &&
(pip2_cmd.seq & 0x07) == (response_seq & 0x07)) {
break;
}
/*
* To reduce the bus and system load, increase the sleep
* step gradually:
* 1 ~ 19 : step=50 us, sleep_us=[50, 100, 150, 200, ..950]
* 20 ~ 39 : step=1000 us, sleep_us=[1950, 2950, ...20950]
* 40 ~ MAX: step=50 ms, sleep_ms=[71, 121, 191,..]
*/
retry++;
if (retry < 20) {
retry_interval += POLL_RETRY_DEFAULT_INTERVAL;
usleep_range(retry_interval,
retry_interval + POLL_RETRY_DEFAULT_INTERVAL);
} else if (retry < 40) {
retry_interval += 1000;
usleep_range(retry_interval, retry_interval + 1000);
} else {
retry_interval += 50000;
msleep(retry_interval/1000);
}
retry_total_time += retry_interval;
}
#else
/*
* Frequent GPIO read will not increase CPU/system load heavily if the
* interval is longer than 10 us, so it is safe to poll GPIO with a
* fixed interval: 20 us.
*/
usleep_range(resp_time_min, resp_time_min+10);
max_retry = resp_time_max / POLL_RETRY_DEFAULT_INTERVAL;
while ((retry < max_retry) && (retry_total_time < resp_time_max)) {
if (!gpio_get_value(cd->cpdata->irq_gpio)) {
rc = pt_adap_read_default(cd, read_buf, read_len);
size = get_unaligned_le16(&read_buf[0]);
if (rc)
pt_debug(dev, DL_ERROR,
"%s: SPI read Error = %d\n",
__func__, rc);
else if (size > read_len) {
pt_debug(cd->dev, DL_ERROR,
"%s: PIP2 len field=%d, requested read_len=%d\n",
__func__, size, read_len);
rc = -EIO;
}
break;
}
/*
* Poll GPIO with fixed interval 20 us, and tollerance is
* limited to 10 us to speed up the process.
*/
retry_interval = POLL_RETRY_DEFAULT_INTERVAL;
usleep_range(retry_interval, retry_interval+10);
retry_total_time += retry_interval;
}
#endif
*actual_read_len = size;
if (rc || (retry >= max_retry) || (retry_total_time >= resp_time_max)) {
pt_debug(dev, DL_ERROR,
"%s cmd[0x%02X] timed out, send_seq=0x%02X, resp_seq=0x%02X\n",
__func__, pip2_cmd.id, pip2_cmd.seq, response_seq);
*actual_read_len = 0;
rc = -EINVAL;
}
pt_pr_buf(cd->dev, DL_DEBUG, read_buf, *actual_read_len,
"<<< NO_INT Read");
exit:
kfree(write_buf);
if (protect == PT_CORE_CMD_PROTECTED) {
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_null_
*
* SUMMARY: Send the PIP "ping"(0x00) command to the DUT and wait for response.
* This function is used by watchdog to check if the fw corrupts.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_pip_null_(struct pt_core_data *cd)
{
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_NULL),
};
return pt_pip1_send_output_and_wait_(cd, &hid_output);
}
/*******************************************************************************
* FUNCTION: pt_pip_null
*
* SUMMARY: Wrapper function for pt_pip_null_ that guarantees exclusive access.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_pip_null(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_null_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
static void pt_stop_wd_timer(struct pt_core_data *cd);
/*******************************************************************************
* FUNCTION: pt_pip_start_bootloader_
*
* SUMMARY: Sends the HID command start_bootloader [PIP cmd 0x01] to the DUT
*
* NOTE: The WD MUST be stopped/restarted by the calling Function. Having
* the WD active could cause this function to fail!
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_pip_start_bootloader_(struct pt_core_data *cd)
{
int rc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_START_BOOTLOADER),
.timeout_ms = PT_PIP1_START_BOOTLOADER_TIMEOUT,
.reset_expected = 1,
};
if (cd->watchdog_enabled) {
pt_debug(cd->dev, DL_WARN,
"%s: watchdog isn't stopped before enter bl\n",
__func__);
goto exit;
}
/* Reset startup status after entering BL, new DUT enum required */
cd->startup_status = STARTUP_STATUS_START;
pt_debug(cd->dev, DL_DEBUG, "%s: Startup Status Reset\n", __func__);
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Start BL PIP cmd failed. rc = %d\n",
__func__, rc);
}
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_start_bootloader
*
* SUMMARY: Protected function to force DUT to enter the BL
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_pip_start_bootloader(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_start_bootloader_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_start_bl
*
* SUMMARY: Function pointer included in core_nonhid_cmds to allow other
* modules to request the DUT to enter the BL
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to run in protected mode
******************************************************************************/
static int _pt_request_pip_start_bl(struct device *dev, int protect)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_start_bootloader(cd);
return pt_pip_start_bootloader_(cd);
}
/*******************************************************************************
* FUNCTION: pt_pip2_ver_load_ttdata
*
* SUMMARY: Function to load the Version information from the PIP2 VERSION
* command into the core data struct.
*
* RETURN: n/a
*
* PARAMETERS:
* *cd - pointer to core data structure
* len - Length of data in response_buf
******************************************************************************/
static void pt_pip2_ver_load_ttdata(struct pt_core_data *cd, u16 len)
{
struct pt_ttdata *ttdata = &cd->sysinfo.ttdata;
struct pt_pip2_version_full *full_ver;
struct pt_pip2_version *ver;
/*
* The PIP2 VERSION command can return different lengths of data.
* The additional LOT fields are included when the packet
* size is >= 29 bytes. Older FW sends a reduced packet size.
* NOTE:
* - The FW would swap the BL and FW versions when reporting
* the small packet.
* - Sub Lot bytes 16 and 17 are reserved.
*/
if (len >= 0x1D) {
full_ver = (struct pt_pip2_version_full *)
&cd->response_buf[PIP2_RESP_STATUS_OFFSET];
ttdata->pip_ver_major = full_ver->pip2_version_msb;
ttdata->pip_ver_minor = full_ver->pip2_version_lsb;
ttdata->bl_ver_major = full_ver->bl_version_msb;
ttdata->bl_ver_minor = full_ver->bl_version_lsb;
ttdata->fw_ver_major = full_ver->fw_version_msb;
ttdata->fw_ver_minor = full_ver->fw_version_lsb;
/*
* BL PIP 2.02 and greater the version fields are
* swapped
*/
if (ttdata->pip_ver_major >= 2 && ttdata->pip_ver_minor >= 2) {
ttdata->chip_rev =
get_unaligned_le16(&full_ver->chip_rev);
ttdata->chip_id =
get_unaligned_le16(&full_ver->chip_id);
} else {
ttdata->chip_rev =
get_unaligned_le16(&full_ver->chip_id);
ttdata->chip_id =
get_unaligned_le16(&full_ver->chip_rev);
}
memcpy(ttdata->uid, full_ver->uid, PT_UID_SIZE);
pt_pr_buf(cd->dev, DL_INFO, (u8 *)full_ver,
sizeof(struct pt_pip2_version_full),
"PIP2 VERSION FULL");
} else {
ver = (struct pt_pip2_version *)
&cd->response_buf[PIP2_RESP_STATUS_OFFSET];
ttdata->pip_ver_major = ver->pip2_version_msb;
ttdata->pip_ver_minor = ver->pip2_version_lsb;
ttdata->bl_ver_major = ver->bl_version_msb;
ttdata->bl_ver_minor = ver->bl_version_lsb;
ttdata->fw_ver_major = ver->fw_version_msb;
ttdata->fw_ver_minor = ver->fw_version_lsb;
ttdata->chip_rev = get_unaligned_le16(&ver->chip_rev);
ttdata->chip_id = get_unaligned_le16(&ver->chip_id);
pt_pr_buf(cd->dev, DL_INFO, (u8 *)ver,
sizeof(struct pt_pip2_version), "PIP2 VERSION");
}
}
/*******************************************************************************
* FUNCTION: pt_si_get_ttdata
*
* SUMMARY: Function to load the version information from the system information
* PIP command into the core data struct.
*
* RETURN: n/a
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static void pt_si_get_ttdata(struct pt_core_data *cd)
{
struct pt_ttdata *ttdata = &cd->sysinfo.ttdata;
struct pt_ttdata_dev *ttdata_dev =
(struct pt_ttdata_dev *)
&cd->response_buf[PIP1_SYSINFO_TTDATA_OFFSET];
ttdata->pip_ver_major = ttdata_dev->pip_ver_major;
ttdata->pip_ver_minor = ttdata_dev->pip_ver_minor;
ttdata->bl_ver_major = ttdata_dev->bl_ver_major;
ttdata->bl_ver_minor = ttdata_dev->bl_ver_minor;
ttdata->fw_ver_major = ttdata_dev->fw_ver_major;
ttdata->fw_ver_minor = ttdata_dev->fw_ver_minor;
ttdata->fw_pid = get_unaligned_le16(&ttdata_dev->fw_pid);
ttdata->fw_ver_conf = get_unaligned_le16(&ttdata_dev->fw_ver_conf);
ttdata->post_code = get_unaligned_le16(&ttdata_dev->post_code);
ttdata->revctrl = get_unaligned_le32(&ttdata_dev->revctrl);
ttdata->jtag_id_l = get_unaligned_le16(&ttdata_dev->jtag_si_id_l);
ttdata->jtag_id_h = get_unaligned_le16(&ttdata_dev->jtag_si_id_h);
memcpy(ttdata->mfg_id, ttdata_dev->mfg_id, PT_NUM_MFGID);
pt_pr_buf(cd->dev, DL_INFO, (u8 *)ttdata_dev,
sizeof(struct pt_ttdata_dev), "sysinfo_ttdata");
}
/*******************************************************************************
* FUNCTION: pt_si_get_sensing_conf_data
*
* SUMMARY: Function to load the sensing information from the system information
* PIP command into the core data struct.
*
* RETURN: n/a
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static void pt_si_get_sensing_conf_data(struct pt_core_data *cd)
{
struct pt_sensing_conf_data *scd = &cd->sysinfo.sensing_conf_data;
struct pt_sensing_conf_data_dev *scd_dev =
(struct pt_sensing_conf_data_dev *)
&cd->response_buf[PIP1_SYSINFO_SENSING_OFFSET];
scd->electrodes_x = scd_dev->electrodes_x;
scd->electrodes_y = scd_dev->electrodes_y;
scd->origin_x = scd_dev->origin_x;
scd->origin_y = scd_dev->origin_y;
/* PIP 1.4 (001-82649 *Q) add X_IS_TX bit in X_ORG */
if (scd->origin_x & 0x02) {
scd->tx_num = scd->electrodes_x;
scd->rx_num = scd->electrodes_y;
} else {
scd->tx_num = scd->electrodes_y;
scd->rx_num = scd->electrodes_x;
}
/*
* When the Panel ID is coming from an XY pin and not a dedicated
* GPIO, store the PID in pid_for_loader. This cannot be done for all
* other DUTs as the loader will use cd->pid_for_loader to generate
* the bin file name but will ignore it if pid_for_loader is still
* set to PANEL_ID_NOT_ENABLED
*/
if (cd->panel_id_support &
(PT_PANEL_ID_BY_BL | PT_PANEL_ID_BY_SYS_INFO)) {
mutex_lock(&cd->system_lock);
cd->pid_for_loader = scd_dev->panel_id;
mutex_unlock(&cd->system_lock);
}
scd->panel_id = scd_dev->panel_id;
scd->btn = scd_dev->btn;
scd->scan_mode = scd_dev->scan_mode;
scd->max_tch = scd_dev->max_num_of_tch_per_refresh_cycle;
scd->res_x = get_unaligned_le16(&scd_dev->res_x);
scd->res_y = get_unaligned_le16(&scd_dev->res_y);
scd->max_z = get_unaligned_le16(&scd_dev->max_z);
scd->len_x = get_unaligned_le16(&scd_dev->len_x);
scd->len_y = get_unaligned_le16(&scd_dev->len_y);
pt_pr_buf(cd->dev, DL_INFO, (u8 *)scd_dev,
sizeof(struct pt_sensing_conf_data_dev),
"sensing_conf_data");
}
/*******************************************************************************
* FUNCTION: pt_si_setup
*
* SUMMARY: Setup the xy_data and xy_mode by allocating the needed memory
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_si_setup(struct pt_core_data *cd)
{
struct pt_sysinfo *si = &cd->sysinfo;
int max_tch = si->sensing_conf_data.max_tch;
if (!si->xy_data)
si->xy_data = kzalloc(max_tch * si->desc.tch_record_size,
GFP_KERNEL);
if (!si->xy_data)
return -ENOMEM;
if (!si->xy_mode)
si->xy_mode = kzalloc(si->desc.tch_header_size, GFP_KERNEL);
if (!si->xy_mode) {
kfree(si->xy_data);
return -ENOMEM;
}
return 0;
}
/*******************************************************************************
* FUNCTION: pt_si_get_btn_data
*
* SUMMARY: Setup the core data button information based on the response of the
* System Information PIP command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_si_get_btn_data(struct pt_core_data *cd)
{
struct pt_sysinfo *si = &cd->sysinfo;
int num_btns = 0;
int num_defined_keys;
u16 *key_table;
int btn;
int i;
int rc = 0;
unsigned int btns = cd->response_buf[PIP1_SYSINFO_BTN_OFFSET]
& PIP1_SYSINFO_BTN_MASK;
size_t btn_keys_size;
pt_debug(cd->dev, DL_INFO, "%s: get btn data\n", __func__);
for (i = 0; i < PIP1_SYSINFO_MAX_BTN; i++) {
if (btns & (1 << i))
num_btns++;
}
si->num_btns = num_btns;
if (num_btns) {
btn_keys_size = num_btns * sizeof(struct pt_btn);
if (!si->btn)
si->btn = kzalloc(btn_keys_size, GFP_KERNEL);
if (!si->btn)
return -ENOMEM;
if (cd->cpdata->sett[PT_IC_GRPNUM_BTN_KEYS] == NULL)
num_defined_keys = 0;
else if (cd->cpdata->sett[PT_IC_GRPNUM_BTN_KEYS]->data == NULL)
num_defined_keys = 0;
else
num_defined_keys = cd->cpdata->sett
[PT_IC_GRPNUM_BTN_KEYS]->size;
for (btn = 0; btn < num_btns && btn < num_defined_keys; btn++) {
key_table = (u16 *)cd->cpdata->sett
[PT_IC_GRPNUM_BTN_KEYS]->data;
si->btn[btn].key_code = key_table[btn];
si->btn[btn].enabled = true;
}
for (; btn < num_btns; btn++) {
si->btn[btn].key_code = KEY_RESERVED;
si->btn[btn].enabled = true;
}
return rc;
}
kfree(si->btn);
si->btn = NULL;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_si_put_log_data
*
* SUMMARY: Prints all sys info data to kmsg log
*
* RETURN: n/a
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static void pt_si_put_log_data(struct pt_core_data *cd)
{
struct pt_sysinfo *si = &cd->sysinfo;
struct pt_ttdata *ttdata = &si->ttdata;
struct pt_sensing_conf_data *scd = &si->sensing_conf_data;
int i;
pt_debug(cd->dev, DL_DEBUG, "%s: pip_ver_major = 0x%02X (%d)\n",
__func__, ttdata->pip_ver_major, ttdata->pip_ver_major);
pt_debug(cd->dev, DL_DEBUG, "%s: pip_ver_minor = 0x%02X (%d)\n",
__func__, ttdata->pip_ver_minor, ttdata->pip_ver_minor);
pt_debug(cd->dev, DL_DEBUG, "%s: fw_pid = 0x%04X (%d)\n",
__func__, ttdata->fw_pid, ttdata->fw_pid);
pt_debug(cd->dev, DL_DEBUG, "%s: fw_ver_major = 0x%02X (%d)\n",
__func__, ttdata->fw_ver_major, ttdata->fw_ver_major);
pt_debug(cd->dev, DL_DEBUG, "%s: fw_ver_minor = 0x%02X (%d)\n",
__func__, ttdata->fw_ver_minor, ttdata->fw_ver_minor);
pt_debug(cd->dev, DL_DEBUG, "%s: revctrl = 0x%08X (%d)\n",
__func__, ttdata->revctrl, ttdata->revctrl);
pt_debug(cd->dev, DL_DEBUG, "%s: fw_ver_conf = 0x%04X (%d)\n",
__func__, ttdata->fw_ver_conf, ttdata->fw_ver_conf);
pt_debug(cd->dev, DL_DEBUG, "%s: bl_ver_major = 0x%02X (%d)\n",
__func__, ttdata->bl_ver_major, ttdata->bl_ver_major);
pt_debug(cd->dev, DL_DEBUG, "%s: bl_ver_minor = 0x%02X (%d)\n",
__func__, ttdata->bl_ver_minor, ttdata->bl_ver_minor);
pt_debug(cd->dev, DL_DEBUG, "%s: jtag_id_h = 0x%04X (%d)\n",
__func__, ttdata->jtag_id_h, ttdata->jtag_id_h);
pt_debug(cd->dev, DL_DEBUG, "%s: jtag_id_l = 0x%04X (%d)\n",
__func__, ttdata->jtag_id_l, ttdata->jtag_id_l);
for (i = 0; i < PT_NUM_MFGID; i++)
pt_debug(cd->dev, DL_DEBUG,
"%s: mfg_id[%d] = 0x%02X (%d)\n",
__func__, i, ttdata->mfg_id[i],
ttdata->mfg_id[i]);
pt_debug(cd->dev, DL_DEBUG, "%s: post_code = 0x%04X (%d)\n",
__func__, ttdata->post_code, ttdata->post_code);
pt_debug(cd->dev, DL_DEBUG, "%s: electrodes_x = 0x%02X (%d)\n",
__func__, scd->electrodes_x, scd->electrodes_x);
pt_debug(cd->dev, DL_DEBUG, "%s: electrodes_y = 0x%02X (%d)\n",
__func__, scd->electrodes_y, scd->electrodes_y);
pt_debug(cd->dev, DL_DEBUG, "%s: len_x = 0x%04X (%d)\n",
__func__, scd->len_x, scd->len_x);
pt_debug(cd->dev, DL_DEBUG, "%s: len_y = 0x%04X (%d)\n",
__func__, scd->len_y, scd->len_y);
pt_debug(cd->dev, DL_DEBUG, "%s: res_x = 0x%04X (%d)\n",
__func__, scd->res_x, scd->res_x);
pt_debug(cd->dev, DL_DEBUG, "%s: res_y = 0x%04X (%d)\n",
__func__, scd->res_y, scd->res_y);
pt_debug(cd->dev, DL_DEBUG, "%s: max_z = 0x%04X (%d)\n",
__func__, scd->max_z, scd->max_z);
pt_debug(cd->dev, DL_DEBUG, "%s: origin_x = 0x%02X (%d)\n",
__func__, scd->origin_x, scd->origin_x);
pt_debug(cd->dev, DL_DEBUG, "%s: origin_y = 0x%02X (%d)\n",
__func__, scd->origin_y, scd->origin_y);
pt_debug(cd->dev, DL_DEBUG, "%s: panel_id = 0x%02X (%d)\n",
__func__, scd->panel_id, scd->panel_id);
pt_debug(cd->dev, DL_DEBUG, "%s: btn =0x%02X (%d)\n",
__func__, scd->btn, scd->btn);
pt_debug(cd->dev, DL_DEBUG, "%s: scan_mode = 0x%02X (%d)\n",
__func__, scd->scan_mode, scd->scan_mode);
pt_debug(cd->dev, DL_DEBUG,
"%s: max_num_of_tch_per_refresh_cycle = 0x%02X (%d)\n",
__func__, scd->max_tch, scd->max_tch);
pt_debug(cd->dev, DL_DEBUG, "%s: xy_mode = %p\n",
__func__, si->xy_mode);
pt_debug(cd->dev, DL_DEBUG, "%s: xy_data = %p\n",
__func__, si->xy_data);
}
/*******************************************************************************
* FUNCTION: pt_get_sysinfo_regs
*
* SUMMARY: Setup all the core data System information based on the response
* of the System Information PIP command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_get_sysinfo_regs(struct pt_core_data *cd)
{
struct pt_sysinfo *si = &cd->sysinfo;
int rc;
rc = pt_si_get_btn_data(cd);
if (rc < 0)
return rc;
pt_si_get_ttdata(cd);
pt_si_get_sensing_conf_data(cd);
pt_si_setup(cd);
pt_si_put_log_data(cd);
si->ready = true;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_free_si_ptrs
*
* SUMMARY: Frees all memory associated with the System Information within
* core data
*
* RETURN: n/a
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static void pt_free_si_ptrs(struct pt_core_data *cd)
{
struct pt_sysinfo *si = &cd->sysinfo;
kfree(si->btn);
kfree(si->xy_mode);
kfree(si->xy_data);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_get_sysinfo_
*
* SUMMARY: Sends the PIP Get SYS INFO command to the DUT and waits for the
* response.
*
* RETURN::
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_hid_output_get_sysinfo_(struct pt_core_data *cd)
{
int rc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_GET_SYSINFO),
.timeout_ms = PT_PIP1_CMD_GET_SYSINFO_TIMEOUT,
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
/* Parse the sysinfo data */
rc = pt_get_sysinfo_regs(cd);
if (rc)
pt_free_si_ptrs(cd);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_get_sysinfo
*
* SUMMARY: Protected call to pt_hid_output_get_sysinfo_
*
* RETURN::
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_hid_output_get_sysinfo(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_get_sysinfo_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_suspend_scanning_
*
* SUMMARY: Sends the PIP Suspend Scanning command to the DUT
*
* RETURN::
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_pip_suspend_scanning_(struct pt_core_data *cd)
{
int rc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_SUSPEND_SCANNING),
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Suspend Scan PIP cmd failed. rc = %d\n",
__func__, rc);
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_suspend_scanning
*
* SUMMARY: Protected wrapper for calling pt_hid_output_suspend_scanning_
*
* RETURN::
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_pip_suspend_scanning(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_suspend_scanning_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_suspend_scanning
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip_suspend_scanning
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - 0 = call non-protected function
* 1 = call protected function
******************************************************************************/
static int _pt_request_pip_suspend_scanning(struct device *dev,
int protect)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_suspend_scanning(cd);
return pt_pip_suspend_scanning_(cd);
}
/*******************************************************************************
* FUNCTION: pt_pip_resume_scanning_
*
* SUMMARY: Sends the PIP Resume Scanning command to the DUT
*
* RETURN::
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_pip_resume_scanning_(struct pt_core_data *cd)
{
int rc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_RESUME_SCANNING),
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Resume Scan PIP cmd failed. rc = %d\n",
__func__, rc);
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_resume_scanning
*
* SUMMARY: Protected wrapper for calling pt_pip_resume_scanning_
*
* RETURN::
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_pip_resume_scanning(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_resume_scanning_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_resume_scanning
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip_resume_scanning
*
* RETURN::
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - 0 = call non-protected function
* 1 = call protected function
******************************************************************************/
static int _pt_request_pip_resume_scanning(struct device *dev,
int protect)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_resume_scanning(cd);
return pt_pip_resume_scanning_(cd);
}
/*******************************************************************************
* FUNCTION: pt_pip_get_param_
*
* SUMMARY: Sends a PIP command 0x05 Get Parameter to the DUT and returns
* the 32bit parameter value
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* param_id - parameter ID to retrieve
* *value - value of DUT parameter
******************************************************************************/
static int pt_pip_get_param_(struct pt_core_data *cd,
u8 param_id, u32 *value)
{
int write_length = 1;
u8 param[1] = { param_id };
u8 read_param_id;
int param_size;
u8 *ptr;
int rc = 0;
int i;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_GET_PARAM),
.write_length = write_length,
.write_buf = param,
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
read_param_id = cd->response_buf[5];
if (read_param_id != param_id)
return -EPROTO;
param_size = cd->response_buf[6];
ptr = &cd->response_buf[7];
*value = 0;
for (i = 0; i < param_size; i++)
*value += ptr[i] << (i * 8);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_pip_get_param
*
* SUMMARY: Protected call to pt_hid_output_get_param_ by a request exclusive
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* param_id - parameter ID to retrieve
* *value - value of DUT parameter
******************************************************************************/
static int pt_pip_get_param(struct pt_core_data *cd,
u8 param_id, u32 *value)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_get_param_(cd, param_id, value);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_get_param
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip_get_param
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non protected function
* param_id - parameter ID to retrieve
* *value - value of DUT parameter
******************************************************************************/
int _pt_request_pip_get_param(struct device *dev,
int protect, u8 param_id, u32 *value)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_get_param(cd, param_id, value);
return pt_pip_get_param_(cd, param_id, value);
}
/*******************************************************************************
* FUNCTION: pt_pip_set_param_
*
* SUMMARY: Sends a PIP command 0x06 Set Parameter to the DUT writing the
* passed in value to flash
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* param_id - parameter ID to set
* value - value to write
* size - size to write
******************************************************************************/
static int pt_pip_set_param_(struct pt_core_data *cd,
u8 param_id, u32 value, u8 size)
{
u8 write_buf[6];
u8 *ptr = &write_buf[2];
int rc = 0;
int i;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_SET_PARAM),
.write_buf = write_buf,
};
write_buf[0] = param_id;
write_buf[1] = size;
for (i = 0; i < size; i++) {
ptr[i] = value & 0xFF;
value = value >> 8;
}
hid_output.write_length = 2 + size;
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
if (param_id != cd->response_buf[5] || size != cd->response_buf[6])
return -EPROTO;
return 0;
}
/*******************************************************************************
* FUNCTION: pt_pip_set_param
*
* SUMMARY: Protected call to pt_hid_output_set_param_ by a request exclusive
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* param_id - parameter ID to set
* value - value to write
* size - size to write
******************************************************************************/
static int pt_pip_set_param(struct pt_core_data *cd,
u8 param_id, u32 value, u8 size)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_set_param_(cd, param_id, value, size);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_set_param
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip_set_param
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* param_id - parameter ID to set
* value - value to write
* size - size to write
******************************************************************************/
int _pt_request_pip_set_param(struct device *dev, int protect,
u8 param_id, u32 value, u8 size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_set_param(cd, param_id, value, size);
return pt_pip_set_param_(cd, param_id, value, size);
}
/*******************************************************************************
* FUNCTION: _pt_pip_enter_easywake_state_
*
* SUMMARY: Sends a PIP command 0x09 Enter EasyWake State to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* data - easywake guesture (Only used for PIP1.6 and earlier)
* *return_data - return status if easywake was entered
******************************************************************************/
static int pt_hid_output_enter_easywake_state_(
struct pt_core_data *cd, u8 data, u8 *return_data)
{
int write_length = 1;
u8 param[1] = { data };
int rc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_ENTER_EASYWAKE_STATE),
.write_length = write_length,
.write_buf = param,
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
*return_data = cd->response_buf[5];
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_verify_config_block_crc_
*
* SUMMARY: Sends the PIP "Verify Data Block CRC" (0x20) command to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
* ebid - enumerated block ID
* *status - PIP command status
* calculated_crc - calculated CRC
* stored_crc - stored CRC in config area
******************************************************************************/
static int pt_pip_verify_config_block_crc_(
struct pt_core_data *cd, u8 ebid, u8 *status,
u16 *calculated_crc, u16 *stored_crc)
{
int write_length = 1;
u8 param[1] = { ebid };
u8 *ptr;
int rc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_VERIFY_CONFIG_BLOCK_CRC),
.write_length = write_length,
.write_buf = param,
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
ptr = &cd->response_buf[5];
*status = ptr[0];
*calculated_crc = get_unaligned_le16(&ptr[1]);
*stored_crc = get_unaligned_le16(&ptr[3]);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_pip_verify_config_block_crc
*
* SUMMARY: Protected call to pt_hid_output_verify_config_block_crc_() within
* an exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
* ebid - enumerated block ID
* *status - PIP command status
* calculated_crc - calculated CRC
* stored_crc - stored CRC in config area
******************************************************************************/
static int pt_pip_verify_config_block_crc(
struct pt_core_data *cd, u8 ebid, u8 *status,
u16 *calculated_crc, u16 *stored_crc)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_verify_config_block_crc_(cd, ebid, status,
calculated_crc, stored_crc);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_verify_config_block_crc
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_pip_verify_config_block_crc_
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* ebid - enumerated block ID
* *status - PIP command status
* calculated_crc - calculated CRC
* stored_crc - stored CRC in config area
******************************************************************************/
static int _pt_request_pip_verify_config_block_crc(
struct device *dev, int protect, u8 ebid, u8 *status,
u16 *calculated_crc, u16 *stored_crc)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_verify_config_block_crc(cd, ebid,
status, calculated_crc, stored_crc);
return pt_pip_verify_config_block_crc_(cd, ebid,
status, calculated_crc, stored_crc);
}
/*******************************************************************************
* FUNCTION: pt_pip_get_config_row_size_
*
* SUMMARY: Sends the PIP "Get Data Row Size" (0x21) command to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* protect - flag to call protected or non-protected
* *row_size - pointer to store the retrieved row size
******************************************************************************/
static int pt_pip_get_config_row_size_(struct pt_core_data *cd,
u16 *row_size)
{
int rc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_GET_CONFIG_ROW_SIZE),
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
*row_size = get_unaligned_le16(&cd->response_buf[5]);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_pip_get_config_row_size
*
* SUMMARY: Protected call to pt_hid_output_get_config_row_size_ within
* an exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* protect - flag to call protected or non-protected
* *row_size - pointer to store the retrieved row size
******************************************************************************/
static int pt_pip_get_config_row_size(struct pt_core_data *cd,
u16 *row_size)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_get_config_row_size_(cd, row_size);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_get_config_row_size
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_pip_get_config_row_size_
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* *row_size - pointer to store the retrieved row size
******************************************************************************/
static int _pt_request_pip_get_config_row_size(struct device *dev,
int protect, u16 *row_size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_get_config_row_size(cd, row_size);
return pt_pip_get_config_row_size_(cd, row_size);
}
/*******************************************************************************
* FUNCTION: pt_pip1_read_data_block_
*
* SUMMARY: Sends the PIP "Read Data Block" (0x22) command to the DUT and print
* output data to the "read_buf" and update "crc".
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* row_number - row number
* length - length of data to read
* ebid - block id
* *actual_read_len - Actual data length read
* *read_buf - pointer to the buffer to store read data
* read_buf_size - size of read_buf
* *crc - pointer to store CRC of row data
******************************************************************************/
static int pt_pip1_read_data_block_(struct pt_core_data *cd,
u16 row_number, u16 length, u8 ebid, u16 *actual_read_len,
u8 *read_buf, u16 read_buf_size, u16 *crc)
{
int read_ebid;
int status;
int rc = 0;
int write_length = 5;
u8 write_buf[5];
u8 cmd_offset = 0;
u16 calc_crc;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_READ_DATA_BLOCK),
.write_length = write_length,
.write_buf = write_buf,
};
write_buf[cmd_offset++] = LOW_BYTE(row_number);
write_buf[cmd_offset++] = HI_BYTE(row_number);
write_buf[cmd_offset++] = LOW_BYTE(length);
write_buf[cmd_offset++] = HI_BYTE(length);
write_buf[cmd_offset++] = ebid;
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
status = cd->response_buf[5];
if (status)
return status;
read_ebid = cd->response_buf[6];
if ((read_ebid != ebid) || (cd->response_buf[9] != 0))
return -EPROTO;
*actual_read_len = get_unaligned_le16(&cd->response_buf[7]);
if (length == 0 || *actual_read_len == 0)
return 0;
if (read_buf_size >= *actual_read_len &&
*actual_read_len < PT_MAX_PIP2_MSG_SIZE)
memcpy(read_buf, &cd->response_buf[10], *actual_read_len);
else
return -EPROTO;
*crc = get_unaligned_le16(&cd->response_buf[*actual_read_len + 10]);
/* Validate Row Data CRC */
calc_crc = _pt_compute_crc(read_buf, *actual_read_len);
if (*crc == calc_crc) {
return 0;
} else {
pt_debug(cd->dev, DL_ERROR,
"%s: CRC Mismatch packet=0x%04X calc=0x%04X\n",
__func__, *crc, calc_crc);
return -EPROTO;
}
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_read_data_block
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to pt_pip1_read_data_block_
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* row_number - row number
* length - length of data to read
* ebid - block id
* *actual_read_len - Actual data length read
* *read_buf - pointer to the buffer to store read data
* *crc - pointer to store CRC of row data
******************************************************************************/
static int _pt_request_pip_read_data_block(struct device *dev,
u16 row_number, u16 length, u8 ebid, u16 *actual_read_len,
u8 *read_buf, u16 read_buf_size, u16 *crc)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return pt_pip1_read_data_block_(cd, row_number, length,
ebid, actual_read_len, read_buf, read_buf_size, crc);
}
/*******************************************************************************
* FUNCTION: pt_pip1_write_data_block_
*
* SUMMARY: Sends the PIP "Write Data Block" (0x23) command to the DUT and
* write data to the data block.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* row_number - row in config block to write to
* write_length - length of data to write
* ebid - enumerated block ID
* *write_buf - pointer to buffer to write
* *security_key - pointer to security key to allow write
* *actual_write_len - pointer to store data length actually written
******************************************************************************/
static int pt_pip1_write_data_block_(struct pt_core_data *cd,
u16 row_number, u16 write_length, u8 ebid, u8 *write_buf,
u8 *security_key, u16 *actual_write_len)
{
/* row_number + write_len + ebid + security_key + crc */
u16 full_write_length = 2 + 2 + 1 + write_length + 8 + 2;
u8 *full_write_buf;
u8 cmd_offset = 0;
u16 crc;
int status;
int rc = 0;
int read_ebid;
u8 *data;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_WRITE_DATA_BLOCK),
.write_length = full_write_length,
.timeout_ms = PT_PIP1_CMD_WRITE_CONF_BLOCK_TIMEOUT,
};
if (write_length > PT_CAL_DATA_ROW_SIZE)
return -EINVAL;
full_write_buf = kzalloc(full_write_length, GFP_KERNEL);
if (!full_write_buf)
return -ENOMEM;
hid_output.write_buf = full_write_buf;
full_write_buf[cmd_offset++] = LOW_BYTE(row_number);
full_write_buf[cmd_offset++] = HI_BYTE(row_number);
full_write_buf[cmd_offset++] = LOW_BYTE(write_length);
full_write_buf[cmd_offset++] = HI_BYTE(write_length);
full_write_buf[cmd_offset++] = ebid;
data = &full_write_buf[cmd_offset];
memcpy(data, write_buf, write_length);
cmd_offset += write_length;
memcpy(&full_write_buf[cmd_offset], security_key, 8);
cmd_offset += 8;
crc = _pt_compute_crc(data, write_length);
full_write_buf[cmd_offset++] = LOW_BYTE(crc);
full_write_buf[cmd_offset++] = HI_BYTE(crc);
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
goto exit;
status = cd->response_buf[5];
if (status) {
rc = -EINVAL;
goto exit;
}
read_ebid = cd->response_buf[6];
if (read_ebid != ebid) {
rc = -EPROTO;
goto exit;
}
*actual_write_len = get_unaligned_le16(&cd->response_buf[7]);
exit:
kfree(full_write_buf);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_write_data_block
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip1_write_data_block_
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* row_number - row in config block to write to
* write_length - length of data to write
* ebid - enumerated block ID
* *write_buf - pointer to buffer to write
* *security_key - pointer to security key to allow write
* *actual_write_len - pointer to store data length actually written
******************************************************************************/
static int _pt_request_pip_write_data_block(struct device *dev,
u16 row_number, u16 write_length, u8 ebid,
u8 *write_buf, u8 *security_key, u16 *actual_write_len)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return pt_pip1_write_data_block_(cd, row_number,
write_length, ebid, write_buf, security_key,
actual_write_len);
}
/*******************************************************************************
* FUNCTION: pt_pip_get_data_structure_
*
* SUMMARY: Sends the PIP "Retrieve Data Structure" (0x24) command to the DUT
* returning a structure of data defined by data_id
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* read_offset - read pointer offset
* read_length - length of data to read
* data_id - data ID to read
* *status - pointer to store the read response status
* *data_format - pointer to store format of data read
* *actual_read_len - pointer to store data length actually read
* *data - pointer to store data read
******************************************************************************/
static int pt_pip_get_data_structure_(
struct pt_core_data *cd, u16 read_offset, u16 read_length,
u8 data_id, u8 *status, u8 *data_format, u16 *actual_read_len,
u8 *data)
{
int rc = 0;
u16 total_read_len = 0;
u16 read_len;
u16 off_buf = 0;
u8 write_buf[5];
u8 read_data_id;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_GET_DATA_STRUCTURE),
.write_length = 5,
.write_buf = write_buf,
};
again:
write_buf[0] = LOW_BYTE(read_offset);
write_buf[1] = HI_BYTE(read_offset);
write_buf[2] = LOW_BYTE(read_length);
write_buf[3] = HI_BYTE(read_length);
write_buf[4] = data_id;
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
if (cd->response_buf[5] != PT_CMD_STATUS_SUCCESS)
goto set_status;
read_data_id = cd->response_buf[6];
if (read_data_id != data_id)
return -EPROTO;
read_len = get_unaligned_le16(&cd->response_buf[7]);
if (read_len && data) {
memcpy(&data[off_buf], &cd->response_buf[10], read_len);
total_read_len += read_len;
if (read_len < read_length) {
read_offset += read_len;
off_buf += read_len;
read_length -= read_len;
goto again;
}
}
if (data_format)
*data_format = cd->response_buf[9];
if (actual_read_len)
*actual_read_len = total_read_len;
set_status:
if (status)
*status = cd->response_buf[5];
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_get_data_structure
*
* SUMMARY: Protected call to pt_hid_output_get_data_structure within
* an exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* read_offset - read pointer offset
* read_length - length of data to read
* data_id - data ID to read
* *status - pointer to store the read response status
* *data_format - pointer to store format of data read
* *actual_read_len - pointer to store data length actually read
* *data - pointer to store data read
******************************************************************************/
static int pt_pip_get_data_structure(
struct pt_core_data *cd, u16 read_offset, u16 read_length,
u8 data_id, u8 *status, u8 *data_format, u16 *actual_read_len,
u8 *data)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_get_data_structure_(cd, read_offset,
read_length, data_id, status, data_format,
actual_read_len, data);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_get_data_structure
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_pip_get_data_structure
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* read_offset - read pointer offset
* read_length - length of data to read
* data_id - data ID to read
* *status - pointer to store the read response status
* *data_format - pointer to store format of data read
* *actual_read_len - pointer to store data length actually read
* *data - pointer to store data read
******************************************************************************/
static int _pt_request_pip_get_data_structure(struct device *dev,
int protect, u16 read_offset, u16 read_length, u8 data_id,
u8 *status, u8 *data_format, u16 *actual_read_len, u8 *data)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_get_data_structure(cd,
read_offset, read_length, data_id, status,
data_format, actual_read_len, data);
return pt_pip_get_data_structure_(cd,
read_offset, read_length, data_id, status,
data_format, actual_read_len, data);
}
/*******************************************************************************
* FUNCTION: _pt_manage_local_cal_data
*
* SUMMARY: This function manages storing or restoring a copy of the Firmware
* CALIBRATION data. It stores it in a local static array and can be
* cleared, loaded or used to restore the CAL data back to the running FW.
* The CAL data is read or restored by use of the PIP1 commands:
* - READ_DATA_BLOCK (0x22)
* - WRITE_DATA_BLOCK (0x23)
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* action - One of the following actions:
* - PT_CAL_DATA_SAVE
* - PT_CAL_DATA_RESTORE
* - PT_CAL_DATA_CLEAR
* - PT_CAL_DATA_SIZE
* *size - pointer to the number of bytes transferred
* *crc - pointer to Chip ID CRC that the CAL data was retrieved from
******************************************************************************/
static int _pt_manage_local_cal_data(struct device *dev, u8 action, u16 *size,
unsigned short *crc)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_ttdata *ttdata = &cd->sysinfo.ttdata;
unsigned short calc_id_crc = 0;
static u8 *cal_cache_data;
static u16 cal_cache_len;
static unsigned short cal_cache_chip_id;
int rc = 0;
u8 *tmp_data = NULL;
u8 row_number = 0;
u8 prefix[20];
u16 cal_size = 0;
u16 transfer_size;
u16 act_trans_len = 0;
u16 byte_offset = 0;
u16 cal_blk_size;
u16 total_rows;
u16 remain_bytes;
u16 data_block_crc;
u16 buf_size = 12;
pt_debug(dev, DL_INFO, "%s: ATM - CAL Cache action=%d\n",
__func__, action);
switch (action) {
case PT_CAL_DATA_SAVE:
/* Read the size of the CAL block and calculate # rows */
tmp_data = kzalloc(buf_size, GFP_KERNEL);
if (!tmp_data) {
rc = -ENOMEM;
goto exit;
}
/*
* Don't check rc as doing a read size will give a false
* error on the CRC check.
*/
rc = pt_pip1_read_data_block_(cd, row_number, 0, PT_CAL_EBID,
&act_trans_len, tmp_data, buf_size, &data_block_crc);
cal_blk_size = act_trans_len;
kfree(tmp_data);
pt_debug(dev, DL_INFO,
"%s: CAL Cache size=%d FW CAL Size=%d\n",
__func__, cal_cache_len, cal_blk_size);
/* Safety net to ensure we didn't read incorrect size */
if (cal_blk_size > PT_CAL_DATA_MAX_SIZE) {
pt_debug(dev, DL_ERROR, "%s: Alloc struct Failed\n",
__func__);
rc = 1;
goto exit;
}
/* Panels could have diff CAL sizes, Re-allocate the cache */
if (cal_blk_size != cal_cache_len) {
kfree(cal_cache_data);
cal_cache_data = kzalloc(cal_blk_size + 2,
GFP_KERNEL);
if (!cal_cache_data) {
rc = -ENOMEM;
goto exit;
}
pt_debug(dev, DL_INFO, "%s: CAL Cache Allocated\n",
__func__);
}
memset(&cal_cache_data[0], 0, cal_blk_size + 2);
/* Calculate how many rows [0-n] (PIP Transactions) */
total_rows = (cal_blk_size / PT_CAL_DATA_ROW_SIZE) - 1;
remain_bytes = cal_blk_size % PT_CAL_DATA_ROW_SIZE;
/* Add row if we have a last partial row */
if (remain_bytes > 0)
total_rows++;
pt_debug(dev, DL_INFO,
"%s: CAL size=%d rows=[0-%d] partial row bytes=%d\n",
__func__, cal_blk_size, total_rows, remain_bytes);
/* Read all rows unless an error occurs */
rc = 0;
while (rc == 0 && row_number <= total_rows) {
act_trans_len = 0;
if (remain_bytes > 0 && row_number == total_rows)
transfer_size = remain_bytes;
else
transfer_size = PT_CAL_DATA_ROW_SIZE;
rc = pt_pip1_read_data_block_(cd, row_number,
transfer_size, PT_CAL_EBID,
&act_trans_len,
&cal_cache_data[byte_offset], cal_blk_size + 2,
&data_block_crc);
if (rc) {
/* Error occurred, exit loop */
cal_size = 0;
break;
}
pt_debug(dev, DL_INFO,
"%s: CAL read rc=%d actual read len=%d\n",
__func__, rc, act_trans_len);
byte_offset += act_trans_len;
cal_size = byte_offset;
scnprintf(prefix, sizeof(prefix), "%s[%d]", "CAL DATA ROW", row_number);
pt_pr_buf(dev, DL_INFO,
&cal_cache_data[byte_offset - act_trans_len],
act_trans_len, prefix);
row_number++;
}
if (cal_size > 0) {
/* Save a CRC of the chip info the CAL was saved from */
calc_id_crc = crc_ccitt_calculate(
(u8 *)&ttdata->chip_rev, 4 + PT_UID_SIZE);
cal_cache_chip_id = calc_id_crc;
cal_cache_len = cal_size;
pt_debug(dev, DL_INFO,
"%s: CAL Cache: CRC=0x%04X Total Size=%d\n",
__func__, calc_id_crc, cal_size);
}
*size = cal_size;
*crc = calc_id_crc;
break;
case PT_CAL_DATA_RESTORE:
cal_size = cal_cache_len;
while ((rc == 0) && (byte_offset < cal_size)) {
if (cal_size - byte_offset > PT_CAL_DATA_ROW_SIZE)
transfer_size = PT_CAL_DATA_ROW_SIZE;
else
transfer_size = cal_size - byte_offset;
rc = pt_pip1_write_data_block_(cd, row_number,
transfer_size, PT_CAL_EBID,
&cal_cache_data[byte_offset],
(u8 *)pt_data_block_security_key,
&act_trans_len);
byte_offset += act_trans_len;
pt_debug(dev, DL_INFO, "%s: CAL write byte offset=%d\n",
__func__, byte_offset);
scnprintf(prefix, sizeof(prefix), "%s[%d]", "CAL DATA ROW", row_number);
pt_pr_buf(dev, DL_INFO,
&cal_cache_data[byte_offset - act_trans_len],
act_trans_len, prefix);
if ((byte_offset > cal_size) ||
(act_trans_len != transfer_size))
rc = -EIO;
row_number++;
}
*size = byte_offset;
*crc = cal_cache_chip_id;
break;
case PT_CAL_DATA_CLEAR:
if (cal_cache_data)
memset(&cal_cache_data[0], 0, cal_cache_len);
cal_cache_len = 0;
cal_cache_chip_id = 0;
*size = 0;
*crc = 0;
break;
case PT_CAL_DATA_INFO:
default:
*size = cal_cache_len;
*crc = cal_cache_chip_id;
pt_debug(dev, DL_INFO,
"%s: CAL Cache: CRC=%04X Total Size=%d\n",
__func__, cal_cache_chip_id,
cal_cache_len);
break;
}
exit:
pt_debug(dev, DL_INFO,
"%s: CAL Cache exit: rc=%d CRC=0x%04X Total Size=%d\n",
__func__, rc, *crc, *size);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_run_selftest_
*
* SUMMARY: Sends the PIP "Run Self Test" (0x26) command to the DUT
* to execute a FW built in self test
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* test_id - enumerated test ID to run
* write_idacs_to_flash - flag whether to write new IDACS to flash
* *status - pointer to store the read response status
* *summary_results - pointer to store the results summary
* *results_available - pointer to store if results are available
*****************************************************************************/
static int pt_pip_run_selftest_(
struct pt_core_data *cd, u8 test_id,
u8 write_idacs_to_flash, u8 *status, u8 *summary_result,
u8 *results_available)
{
int rc = 0;
u8 write_buf[2];
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_RUN_SELF_TEST),
.write_length = 2,
.write_buf = write_buf,
.timeout_ms = PT_PIP1_CMD_RUN_SELF_TEST_TIMEOUT,
};
write_buf[0] = test_id;
write_buf[1] = write_idacs_to_flash;
if (cd->active_dut_generation == DUT_PIP2_CAPABLE)
hid_output.write_length = 1;
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
if (status)
*status = cd->response_buf[5];
if (summary_result)
*summary_result = cd->response_buf[6];
/* results_available only available before PIP 1.03 */
if (cd->sysinfo.ready && !IS_PIP_VER_GE(&cd->sysinfo, 1, 3)) {
if (results_available)
*results_available = cd->response_buf[7];
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_run_selftest
*
* SUMMARY: Protected call to pt_hid_output_run_selftest within
* an exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* test_id - enumerated test ID to run
* write_idacs_to_flash - flag whether to write new IDACS to flash
* *status - pointer to store the read response status
* *summary_results - pointer to store the results summary
* *results_available - pointer to store if results are available
******************************************************************************/
static int pt_pip_run_selftest(
struct pt_core_data *cd, u8 test_id,
u8 write_idacs_to_flash, u8 *status, u8 *summary_result,
u8 *results_available)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_run_selftest_(cd, test_id,
write_idacs_to_flash, status, summary_result,
results_available);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_run_selftest
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip_run_selftest
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* test_id - enumerated test ID to run
* write_idacs_to_flash - flag whether to write new IDACS to flash
* *status - pointer to store the read response status
* *summary_results - pointer to store the results summary
* *results_available - pointer to store if results are available
******************************************************************************/
static int _pt_request_pip_run_selftest(struct device *dev,
int protect, u8 test_id, u8 write_idacs_to_flash, u8 *status,
u8 *summary_result, u8 *results_available)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_run_selftest(cd, test_id,
write_idacs_to_flash, status, summary_result,
results_available);
return pt_pip_run_selftest_(cd, test_id,
write_idacs_to_flash, status, summary_result,
results_available);
}
/*******************************************************************************
* FUNCTION: _pt_pip_get_selftest_result_
*
* SUMMARY: Sends the PIP "Get Self Test Results" (0x27) command to the DUT
* to retrieve the self test results from the self test already executed
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* read_offset - read pointer offset
* read_length - length of data to read
* test_id - enumerated test ID to read selftest results from
* *status - pointer to store the read response status
* *actual_read_len - pointer to store data length actually read
* *status - pointer to where the cmd response statas is stored
******************************************************************************/
static int pt_pip_get_selftest_result_(
struct pt_core_data *cd, u16 read_offset, u16 read_length,
u8 test_id, u8 *status, u16 *actual_read_len, u8 *data)
{
int rc = 0;
u16 total_read_len = 0;
u16 read_len;
u16 off_buf = 0;
u8 write_buf[5];
u8 read_test_id;
bool repeat;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_GET_SELF_TEST_RESULT),
.write_length = 5,
.write_buf = write_buf,
};
/*
* Do not repeat reading for Auto Shorts test
* when PIP version < 1.3
*/
repeat = IS_PIP_VER_GE(&cd->sysinfo, 1, 3)
|| test_id != PT_ST_ID_AUTOSHORTS;
again:
write_buf[0] = LOW_BYTE(read_offset);
write_buf[1] = HI_BYTE(read_offset);
write_buf[2] = LOW_BYTE(read_length);
write_buf[3] = HI_BYTE(read_length);
write_buf[4] = test_id;
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
if (cd->response_buf[5] != PT_CMD_STATUS_SUCCESS)
goto set_status;
read_test_id = cd->response_buf[6];
if (read_test_id != test_id)
return -EPROTO;
read_len = get_unaligned_le16(&cd->response_buf[7]);
if (read_len && data) {
memcpy(&data[off_buf], &cd->response_buf[10], read_len);
total_read_len += read_len;
if (repeat && read_len < read_length) {
read_offset += read_len;
off_buf += read_len;
read_length -= read_len;
goto again;
}
}
if (actual_read_len)
*actual_read_len = total_read_len;
set_status:
if (status)
*status = cd->response_buf[5];
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_pip_get_selftest_result
*
* SUMMARY: Protected call to pt_hid_output_get_selftest_result by exclusive
* access to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* read_offset - read pointer offset
* read_length - length of data to read
* test_id - enumerated test ID to read selftest results from
* *status - pointer to store the read response status
* *actual_read_len - pointer to store data length actually read
* *status - pointer to where the cmd response statas is stored
******************************************************************************/
static int pt_pip_get_selftest_result(
struct pt_core_data *cd, u16 read_offset, u16 read_length,
u8 test_id, u8 *status, u16 *actual_read_len, u8 *data)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_get_selftest_result_(cd, read_offset,
read_length, test_id, status, actual_read_len, data);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_get_selftest_result
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip_get_selftest_result
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* read_offset - read pointer offset
* read_length - length of data to read
* test_id - enumerated test ID to read selftest results from
* *status - pointer to store the read response status
* *actual_read_len - pointer to store data length actually read
* *data - pointer to where the data read is stored
******************************************************************************/
static int _pt_request_pip_get_selftest_result(struct device *dev,
int protect, u16 read_offset, u16 read_length, u8 test_id,
u8 *status, u16 *actual_read_len, u8 *data)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_get_selftest_result(cd, read_offset,
read_length, test_id, status, actual_read_len,
data);
return pt_pip_get_selftest_result_(cd, read_offset,
read_length, test_id, status, actual_read_len,
data);
}
/*******************************************************************************
* FUNCTION: _pt_pip_load_self_test_param
*
* SUMMARY: Sends the PIP "Load Self Test Parameters" (0x25) command to the DUT
* to load parameters needed by a self test
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* self_test_id - enumerated test ID for which the parmeters belong
* load_offset - mem offset to where to load parameters
* load_length - length of parameter data to load
* *parameters - pointer to list of parameter data
* *status - pointer to store the response status
* *ret_test_id - pointer to returned test id the parameters were stored
* *act_load_len - pointer to store the actual load length that was writen
******************************************************************************/
static int pt_pip_load_self_test_param_(struct pt_core_data *cd,
u8 self_test_id, u16 load_offset, u16 load_length,
u8 *parameters, u8 *status, u8 *ret_test_id, u16 *act_load_len)
{
int rc = 0;
int i;
u8 write_buf[PT_MAX_PIP1_MSG_SIZE];
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_LOAD_SELF_TEST_PARAM),
.write_length = 5 + load_length,
.write_buf = write_buf,
.timeout_ms = PT_PIP1_CMD_DEFAULT_TIMEOUT,
};
write_buf[0] = LOW_BYTE(load_offset);
write_buf[1] = HI_BYTE(load_offset);
write_buf[2] = LOW_BYTE(load_length);
write_buf[3] = HI_BYTE(load_length);
write_buf[4] = self_test_id;
for (i = 0; i < load_length; i++)
write_buf[i + 5] = parameters[i];
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
if (status)
*status = cd->response_buf[5];
if (ret_test_id)
*ret_test_id = cd->response_buf[6];
if (act_load_len)
*act_load_len = get_unaligned_le16(&cd->response_buf[7]);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip_load_self_test_param
*
* SUMMARY: Protected call to pt_pip_load_self_test_param_ within an exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* self_test_id - enumerated test ID for which the parmeters belong
* load_offset - mem offset to where to load parameters
* load_length - length of parameter data to load
* *parameters - pointer to list of parameter data
* *status - pointer to store the response status
* *ret_test_id - pointer to returned test id the parameters were stored
* *act_load_len - pointer to store the actual load length that was writen
******************************************************************************/
static int pt_pip_load_self_test_param(struct pt_core_data *cd,
u8 self_test_id, u16 load_offset, u16 load_length,
u8 *parameters, u8 *status, u8 *ret_test_id, u16 *act_load_len)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_load_self_test_param_(cd, self_test_id, load_offset,
load_length, parameters, status, ret_test_id, act_load_len);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_load_self_test_param
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_pip_load_self_test_param
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* self_test_id - enumerated test ID for which the parmeters belong
* load_offset - mem offset to where to load parameters
* load_length - length of parameter data to load
* *parameters - pointer to list of parameter data
* *status - pointer to store the response status
* *ret_test_id - pointer to returned test id the parameters were stored
* *act_load_len - pointer to store the actual load length that was writen
******************************************************************************/
static int _pt_request_pip_load_self_test_param(struct device *dev,
int protect, u8 self_test_id, u16 load_offset, u16 load_length,
u8 *parameters, u8 *status, u8 *ret_test_id, u16 *act_load_len)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_load_self_test_param(cd, self_test_id,
load_offset, load_length, parameters, status, ret_test_id,
act_load_len);
return pt_pip_load_self_test_param_(cd, self_test_id, load_offset,
load_length, parameters, status, ret_test_id, act_load_len);
}
/*******************************************************************************
* FUNCTION: pt_pip_calibrate_ext_
*
* SUMMARY: Send the PIP1 Extended Calibrate command (0x30) to the DUT waiting
* for the response
*
* NOTE: This calibrate command requires the DUT to support PIP version >= 1.10
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *cal_data - pointer to extended calibration data structure
* *status - pointer to where the command response status is stored
******************************************************************************/
static int pt_pip_calibrate_ext_(struct pt_core_data *cd,
struct pt_cal_ext_data *cal_data, u8 *status)
{
int rc = 0;
int write_length = 4;
u8 write_buf[4];
u16 size = 0;
unsigned short crc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_CALIBRATE_DEVICE_EXTENDED),
.write_length = write_length,
.write_buf = write_buf,
.timeout_ms = PT_PIP1_CMD_CALIBRATE_EXT_TIMEOUT,
};
if (cal_data == NULL)
return -EINVAL;
memcpy(write_buf, cal_data, sizeof(struct pt_cal_ext_data));
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
if (status)
*status = cd->response_buf[5];
/*
* When doing a calibration on a flashless DUT, save CAL data in
* the TTDL cache on any successful calibration
*/
if (cd->response_buf[5] == 0 && cd->cal_cache_in_host) {
pt_debug(cd->dev, DL_INFO, "%s: Retrieve and Save CAL\n",
__func__);
rc = _pt_manage_local_cal_data(cd->dev, PT_CAL_DATA_SAVE,
&size, &crc);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: Error Saving CAL rc=%d\n", __func__, rc);
else
pt_debug(cd->dev, DL_INFO,
"%s: Saved CAL: chip ID=0x%04X size=%d\n",
__func__, crc, size);
}
return 0;
}
/*******************************************************************************
* FUNCTION: pt_pip_calibrate_ext
*
* SUMMARY: Protected call to pt_pip_calibrate_ext_ by exclusive access to the
* DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *cal_data - pointer to extended calibration data structure
* *status - pointer to where the command response status is stored
******************************************************************************/
static int pt_pip_calibrate_ext(struct pt_core_data *cd,
struct pt_cal_ext_data *cal_data, u8 *status)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_calibrate_ext_(cd, cal_data, status);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_calibrate_ext
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip_calibrate_ext
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* *cal_data - pointer to extended calibration data structure
* *status - pointer to where the command response status is stored
******************************************************************************/
static int _pt_request_pip_calibrate_ext(struct device *dev,
int protect, struct pt_cal_ext_data *cal_data, u8 *status)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_calibrate_ext(cd, cal_data, status);
return pt_pip_calibrate_ext_(cd, cal_data, status);
}
/*******************************************************************************
* FUNCTION: pt_pip_calibrate_idacs_
*
* SUMMARY: Send the PIP Calibrate IDACs command (0x28) to the DUT waiting
* for the response
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* mode - sense mode to calibrate (0-5)
* *status - pointer to where the command response status is stored
******************************************************************************/
static int pt_pip_calibrate_idacs_(struct pt_core_data *cd,
u8 mode, u8 *status)
{
int rc = 0;
int write_length = 1;
u8 write_buf[1];
u8 cmd_offset = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_CALIBRATE_IDACS),
.write_length = write_length,
.write_buf = write_buf,
.timeout_ms = PT_PIP1_CMD_CALIBRATE_IDAC_TIMEOUT,
};
write_buf[cmd_offset++] = mode;
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
*status = cd->response_buf[5];
if (*status)
return -EINVAL;
return 0;
}
/*******************************************************************************
* FUNCTION: pt_pip_calibrate_idacs
*
* SUMMARY: Protected call to pt_hid_output_calibrate_idacs_ by exclusive
* access to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* mode - sense mode to calibrate (0-5)
* *status - pointer to where the command response status is stored
******************************************************************************/
static int pt_pip_calibrate_idacs(struct pt_core_data *cd,
u8 mode, u8 *status)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip_calibrate_idacs_(cd, mode, status);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_calibrate_idacs
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to pt_pip_calibrate_idacs
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* mode - sense mode to calibrate (0-5)
* *status - pointer to where the command response status is stored
******************************************************************************/
static int _pt_request_pip_calibrate_idacs(struct device *dev,
int protect, u8 mode, u8 *status)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip_calibrate_idacs(cd, mode, status);
return pt_pip_calibrate_idacs_(cd, mode, status);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_initialize_baselines_
*
* SUMMARY: Send the PIP "Initialize Baselines" command (0x29) to the DUT
* waiting for the response.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* test_id - bit type flag to allow initialize baseline MUT,BTN,SELG
* each or together with a single command.
* *status - pointer to where the command response status is stored
******************************************************************************/
static int pt_hid_output_initialize_baselines_(
struct pt_core_data *cd, u8 test_id, u8 *status)
{
int rc = 0;
int write_length = 1;
u8 write_buf[1];
u8 cmd_offset = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_INITIALIZE_BASELINES),
.write_length = write_length,
.write_buf = write_buf,
};
write_buf[cmd_offset++] = test_id;
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
*status = cd->response_buf[5];
if (*status)
return -EINVAL;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_initialize_baselines
*
* SUMMARY: Protected call to pt_hid_output_initialize_baselines_ by exclusive
* access to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* test_id - enumerated ID against which to initialize the baseline
* *status - pointer to where the command response status is stored
******************************************************************************/
static int pt_hid_output_initialize_baselines(struct pt_core_data *cd,
u8 test_id, u8 *status)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_initialize_baselines_(cd, test_id, status);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_initialize_baselines
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_pip_initialize_baselines
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* test_id - enumerated ID against which to initialize the baseline
* *status - pointer to where the command response status is stored
******************************************************************************/
static int _pt_request_pip_initialize_baselines(struct device *dev,
int protect, u8 test_id, u8 *status)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_initialize_baselines(cd, test_id,
status);
return pt_hid_output_initialize_baselines_(cd, test_id, status);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_exec_panel_scan_
*
* SUMMARY: Sends the PIP "Execute Panel Scan" (0x2A) to the DUT and waits for
* the response
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_hid_output_exec_panel_scan_(struct pt_core_data *cd)
{
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_EXEC_PANEL_SCAN),
};
return pt_pip1_send_output_and_wait_(cd, &hid_output);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_exec_panel_scan
*
* SUMMARY: Protected call to pt_hid_output_exec_panel_scan_ by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_hid_output_exec_panel_scan(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_exec_panel_scan_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_exec_panel_scan_
*
* SUMMARY: Send the PIP2 "Execute Panel Scan" (0x21) to the DUT and waits for
* the response
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* scan_type - type of panel scan to perform (PIP2 only)
******************************************************************************/
static int pt_pip2_exec_panel_scan_(struct pt_core_data *cd, u8 scan_type)
{
int rc = 0;
u8 data[2];
u8 read_buf[10];
u16 actual_read_len;
pt_debug(cd->dev, DL_DEBUG, "%s: PIP2 Execute Scan %d\n",
__func__, scan_type);
data[0] = scan_type;
rc = _pt_request_pip2_send_cmd(cd->dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_EXECUTE_SCAN,
data, 1, read_buf, &actual_read_len);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s EXECUTE_SCAN command for type %d failed. rc=%d\n",
__func__, scan_type, rc);
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_exec_panel_scan
*
* SUMMARY: Protected call to pt_pip2_exec_panel_scan_ by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* scan_type - type of panel scan to perform (PIP2 only)
******************************************************************************/
static int pt_pip2_exec_panel_scan(struct pt_core_data *cd, u8 scan_type)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip2_exec_panel_scan_(cd, scan_type);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_exec_panel_scan
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_pip2_exec_panel_scan or pt_hid_output_exec_panel_scan
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* scan_type - type of panel scan to perform (PIP2 only)
******************************************************************************/
static int _pt_request_pip_exec_panel_scan(struct device *dev,
int protect, u8 scan_type)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (cd->sysinfo.ready && IS_PIP_VER_GE(&cd->sysinfo, 1, 12)) {
if (protect)
return pt_pip2_exec_panel_scan(cd, scan_type);
return pt_pip2_exec_panel_scan_(cd, scan_type);
}
if (protect)
return pt_hid_output_exec_panel_scan(cd);
return pt_hid_output_exec_panel_scan_(cd);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_retrieve_panel_scan_
*
* SUMMARY: Sends the PIP "Retrieve Panel Scan" (0x2B) command to the DUT
* to retrieve the specified data type for a the last successful Execute
* Panel Scan command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* read_offset - read pointer offset
* read_count - length of data to read
* data_id - enumerated test ID to read selftest results from
* *response - pointer to store the read response status
* *config - pointer to store config data
* *actual_read_len - pointer to store data length actually read
* *read_buf - pointer to the read buffer
******************************************************************************/
static int pt_hid_output_retrieve_panel_scan_(
struct pt_core_data *cd, u16 read_offset, u16 read_count,
u8 data_id, u8 *response, u8 *config, u16 *actual_read_len,
u8 *read_buf)
{
int status;
u8 read_data_id;
int rc = 0;
int write_length = 5;
u8 write_buf[5];
u8 cmd_offset = 0;
u8 data_elem_size;
int size;
int data_size;
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_RETRIEVE_PANEL_SCAN),
.write_length = write_length,
.write_buf = write_buf,
};
write_buf[cmd_offset++] = LOW_BYTE(read_offset);
write_buf[cmd_offset++] = HI_BYTE(read_offset);
write_buf[cmd_offset++] = LOW_BYTE(read_count);
write_buf[cmd_offset++] = HI_BYTE(read_count);
write_buf[cmd_offset++] = data_id;
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
status = cd->response_buf[5];
if (status)
return -EINVAL;
read_data_id = cd->response_buf[6];
if (read_data_id != data_id)
return -EPROTO;
size = get_unaligned_le16(&cd->response_buf[0]);
*actual_read_len = get_unaligned_le16(&cd->response_buf[7]);
*config = cd->response_buf[9];
data_elem_size = *config & 0x07;
data_size = *actual_read_len * data_elem_size;
if (read_buf)
memcpy(read_buf, &cd->response_buf[10], data_size);
if (response)
memcpy(response, cd->response_buf, size);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_retrieve_panel_scan
*
* SUMMARY: Protected call to pt_hid_output_retrieve_panel_scan_ by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* read_offset - read pointer offset
* read_count - length of data to read
* data_id - enumerated test ID to read selftest results from
* *response - pointer to store the read response status
* *config - pointer to store config data
* *actual_read_len - pointer to store data length actually read
* *read_buf - pointer to the read buffer
******************************************************************************/
static int pt_hid_output_retrieve_panel_scan(
struct pt_core_data *cd, u16 read_offset, u16 read_count,
u8 data_id, u8 *response, u8 *config, u16 *actual_read_len,
u8 *read_buf)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_retrieve_panel_scan_(cd, read_offset,
read_count, data_id, response, config,
actual_read_len, read_buf);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_retrieve_panel_scan
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_hid_output_retrieve_panel_scan
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* read_offset - read pointer offset
* read_count - length of data to read
* data_id - enumerated test ID to read selftest results from
* *response - pointer to store the read response status
* *config - pointer to store config data
* *actual_read_len - pointer to store data length actually read
* *read_buf - pointer to the read buffer
******************************************************************************/
static int _pt_request_pip_retrieve_panel_scan(struct device *dev,
int protect, u16 read_offset, u16 read_count, u8 data_id,
u8 *response, u8 *config, u16 *actual_read_len, u8 *read_buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_retrieve_panel_scan(cd,
read_offset, read_count, data_id, response,
config, actual_read_len, read_buf);
return pt_hid_output_retrieve_panel_scan_(cd,
read_offset, read_count, data_id, response,
config, actual_read_len, read_buf);
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_user_cmd
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_hid_output_user_cmd
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* read_len - length of data to read
* *read_buf - pointer to store read data
* write_len - length of data to write
* *write_buf - pointer to buffer to write
* *actual_read_len - pointer to store data length actually read
******************************************************************************/
static int _pt_request_pip_user_cmd(struct device *dev,
int protect, u16 read_len, u8 *read_buf, u16 write_len,
u8 *write_buf, u16 *actual_read_len)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_user_cmd(cd, read_len, read_buf,
write_len, write_buf, actual_read_len);
return pt_hid_output_user_cmd_(cd, read_len, read_buf,
write_len, write_buf, actual_read_len);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_get_information_
*
* SUMMARY: Sends the PIP "Get Bootloader Information" (0x38) command to the
* DUT to retrieve bootloader version and chip identification information.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *return_data - pointer to store the return data
*****************************************************************************/
static int pt_hid_output_bl_get_information_(struct pt_core_data *cd,
u8 *return_data)
{
int rc;
int data_len;
struct pt_hid_output hid_output = {
CREATE_PIP1_BL_CMD(PIP1_BL_CMD_ID_GET_INFO),
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
return rc;
data_len = get_unaligned_le16(&cd->input_buf[6]);
if (!data_len)
return -EPROTO;
memcpy(return_data, &cd->response_buf[8], data_len);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_get_information
*
* SUMMARY: Protected call to pt_hid_output_bl_get_information_ by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *return_data - pointer to store the return data
******************************************************************************/
static int pt_hid_output_bl_get_information(struct pt_core_data *cd,
u8 *return_data)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_bl_get_information_(cd, return_data);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_bl_get_information
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_hid_output_bl_get_information
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* *return_data - pointer to store bl data
******************************************************************************/
static int _pt_request_pip_bl_get_information(struct device *dev,
int protect, u8 *return_data)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_bl_get_information(cd, return_data);
return pt_hid_output_bl_get_information_(cd, return_data);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_initiate_bl_
*
* SUMMARY: Sends the PIP "Get Bootloader Information" (0x48) command to the
* DUT to erases the entire TrueTouch application, Configuration Data block,
* and Design Data block in flash and enables the host to execute the Program
* and Verify Row command to bootload the application image and data.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* protect - flag to call protected or non-protected
* key_size - size of key
* *key_buf - pointer to key data to allow operation
* row_size - size of the meta data row
* *metadata_row_buf - pointer to meta data to write
******************************************************************************/
static int pt_hid_output_bl_initiate_bl_(struct pt_core_data *cd,
u16 key_size, u8 *key_buf, u16 row_size, u8 *metadata_row_buf)
{
u16 write_length = key_size + row_size;
u8 *write_buf;
int rc = 0;
struct pt_hid_output hid_output = {
CREATE_PIP1_BL_CMD(PIP1_BL_CMD_ID_INITIATE_BL),
.write_length = write_length,
.timeout_ms = PT_PIP1_CMD_INITIATE_BL_TIMEOUT,
};
write_buf = kzalloc(write_length, GFP_KERNEL);
if (!write_buf)
return -ENOMEM;
hid_output.write_buf = write_buf;
if (key_size)
memcpy(write_buf, key_buf, key_size);
if (row_size)
memcpy(&write_buf[key_size], metadata_row_buf, row_size);
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
kfree(write_buf);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_initiate_bl
*
* SUMMARY: Protected call to pt_hid_output_bl_initiate_bl_ by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* key_size - size of key
* *key_buf - pointer to key data to allow operation
* row_size - size of the meta data row
* *metadata_row_buf - pointer to meta data to write
******************************************************************************/
static int pt_hid_output_bl_initiate_bl(struct pt_core_data *cd,
u16 key_size, u8 *key_buf, u16 row_size, u8 *metadata_row_buf)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_bl_initiate_bl_(cd, key_size, key_buf,
row_size, metadata_row_buf);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_bl_initiate_bl
*
* SUMMARY: Function pointer included in core_nonhid_cmd struct for external
* calls to the protected or unprotected call to
* pt_hid_output_bl_initiate_bl
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* key_size - size of key
* *key_buf - pointer to key data to allow operation
* row_size - size of the meta data row
* *metadata_row_buf - pointer to meta data to write
******************************************************************************/
static int _pt_request_pip_bl_initiate_bl(struct device *dev,
int protect, u16 key_size, u8 *key_buf, u16 row_size,
u8 *metadata_row_buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_bl_initiate_bl(cd, key_size, key_buf,
row_size, metadata_row_buf);
return pt_hid_output_bl_initiate_bl_(cd, key_size, key_buf,
row_size, metadata_row_buf);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_program_and_verify_
*
* SUMMARY: Sends the PIP "Get Bootloader Information" (0x39) command to upload
* and program a 128-byte row into the flash, and then verifies written data.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* data_len - length of data_buf
* *data_buf - firmware image to program
******************************************************************************/
static int pt_hid_output_bl_program_and_verify_(
struct pt_core_data *cd, u16 data_len, u8 *data_buf)
{
struct pt_hid_output hid_output = {
CREATE_PIP1_BL_CMD(PIP1_BL_CMD_ID_PROGRAM_AND_VERIFY),
.write_length = data_len,
.write_buf = data_buf,
.timeout_ms = PT_PIP1_CMD_PROGRAM_AND_VERIFY_TIMEOUT,
};
return pt_pip1_send_output_and_wait_(cd, &hid_output);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_program_and_verify
*
* SUMMARY: Protected call to pt_hid_output_bl_program_and_verify_ by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* data_len - length of data_buf
* *data_buf - firmware image to program
******************************************************************************/
static int pt_hid_output_bl_program_and_verify(
struct pt_core_data *cd, u16 data_len, u8 *data_buf)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_bl_program_and_verify_(cd, data_len, data_buf);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_bl_program_and_verify
*
* SUMMARY: Function pointer included in core_nonhid_cmds to allow other modules
* to request to have the BL program and verify a FW image
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - boolean to determine to call the protected function
* data_len - length of data_buf
* *data_buf - firmware image to program
******************************************************************************/
static int _pt_request_pip_bl_program_and_verify(
struct device *dev, int protect, u16 data_len, u8 *data_buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_bl_program_and_verify(cd, data_len,
data_buf);
return pt_hid_output_bl_program_and_verify_(cd, data_len,
data_buf);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_verify_app_integrity_
*
* SUMMARY: Sends the PIP "Get Bootloader Information" (0x31) command to
* perform a full verification of the application integrity by calculating the
* CRC of the image in flash and compare it to the expected CRC stored in the
* Metadata row.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *result - pointer to store result
******************************************************************************/
static int pt_hid_output_bl_verify_app_integrity_(
struct pt_core_data *cd, u8 *result)
{
int rc;
struct pt_hid_output hid_output = {
CREATE_PIP1_BL_CMD(PIP1_BL_CMD_ID_VERIFY_APP_INTEGRITY),
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc) {
*result = 0;
return rc;
}
*result = cd->response_buf[8];
return 0;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_verify_app_integrity
*
* SUMMARY: Protected call to pt_hid_output_bl_verify_app_integrity_ by
* exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *result - pointer to store result
******************************************************************************/
static int pt_hid_output_bl_verify_app_integrity(
struct pt_core_data *cd, u8 *result)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_bl_verify_app_integrity_(cd, result);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_bl_verify_app_integrity
*
* SUMMARY: Function pointer included in core_nonhid_cmds to allow other modules
* to request to have the BL verify the application integrity (PIP1.x only)
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - boolean to determine to call the protected function
* *result - pointer to store result
******************************************************************************/
static int _pt_request_pip_bl_verify_app_integrity(
struct device *dev, int protect, u8 *result)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_bl_verify_app_integrity(cd, result);
return pt_hid_output_bl_verify_app_integrity_(cd, result);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_launch_app_
*
* SUMMARY: Sends the PIP "Launch Application" (0x3B) command to launch the
* application from bootloader (PIP1.x only).
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_hid_output_bl_launch_app_(struct pt_core_data *cd)
{
struct pt_hid_output hid_output = {
CREATE_PIP1_BL_CMD(PIP1_BL_CMD_ID_LAUNCH_APP),
.reset_expected = 1,
};
return pt_pip1_send_output_and_wait_(cd, &hid_output);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_launch_app
*
* SUMMARY: Protected call to pt_hid_output_bl_launch_app_ by exclusive access
* to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_hid_output_bl_launch_app(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_bl_launch_app_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_launch_app
*
* SUMMARY: Function pointer included in core_nonhid_cmds to allow other modules
* to request to have the BL launch the application. (PIP1.x only)
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - boolean to determine to call the protected function
******************************************************************************/
static int _pt_request_pip_launch_app(struct device *dev,
int protect)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_bl_launch_app(cd);
return pt_hid_output_bl_launch_app_(cd);
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_get_panel_id_
*
* SUMMARY: Sends the PIP "Get Panel ID" (0x3E) command to return the Panel ID
* value store in the System Information.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *panel_id - pointer to where the panel ID will be stored
******************************************************************************/
static int pt_hid_output_bl_get_panel_id_(
struct pt_core_data *cd, u8 *panel_id)
{
int rc;
struct pt_hid_output hid_output = {
CREATE_PIP1_BL_CMD(PIP1_BL_CMD_ID_GET_PANEL_ID),
};
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc == -EPROTO && cd->response_buf[5] == ERROR_COMMAND) {
pt_debug(cd->dev, DL_ERROR,
"%s: Get Panel ID command not supported\n",
__func__);
*panel_id = PANEL_ID_NOT_ENABLED;
return 0;
} else if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on Get Panel ID command\n", __func__);
return rc;
}
*panel_id = cd->response_buf[8];
return 0;
}
/*******************************************************************************
* FUNCTION: pt_hid_output_bl_get_panel_id
*
* SUMMARY: Protected call to pt_hid_output_bl_get_panel_id_ by exclusive access
* to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *panel_id - pointer to where the panel ID will be stored
******************************************************************************/
static int pt_hid_output_bl_get_panel_id(
struct pt_core_data *cd, u8 *panel_id)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_hid_output_bl_get_panel_id_(cd, panel_id);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip_bl_get_panel_id
*
* SUMMARY: Function pointer included in core_nonhid_cmds to allow other modules
* to have the BL retrieve the panel ID
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to run in protected mode
* *panel_id - pointer to where the panel ID will be stored
******************************************************************************/
static int _pt_request_pip_bl_get_panel_id(
struct device *dev, int protect, u8 *panel_id)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_hid_output_bl_get_panel_id(cd, panel_id);
return pt_hid_output_bl_get_panel_id_(cd, panel_id);
}
/*******************************************************************************
* FUNCTION: pt_pip2_get_mode_sysmode_
*
* SUMMARY: Determine the current mode and system mode of the DUT by use of the
* PIP2 STATUS command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
* *mode - pointer to store the retrieved mode
* *sys_mode - pointer to store the FW system mode
******************************************************************************/
static int pt_pip2_get_mode_sysmode_(struct pt_core_data *cd,
u8 *mode, u8 *sys_mode)
{
u16 actual_read_len;
u8 read_buf[12];
u8 status, boot;
int rc = 0;
rc = _pt_request_pip2_send_cmd(cd->dev, PT_CORE_CMD_UNPROTECTED,
PIP2_CMD_ID_STATUS, NULL, 0, read_buf, &actual_read_len);
pt_debug(cd->dev, DL_INFO, "%s: PIP2 STATUS command rc = %d\n",
__func__, rc);
if (!rc) {
pt_pr_buf(cd->dev, DL_DEBUG, read_buf, actual_read_len,
"PIP2 STATUS");
status = read_buf[PIP2_RESP_STATUS_OFFSET];
boot = read_buf[PIP2_RESP_BODY_OFFSET] & 0x01;
if (sys_mode) {
if (status == PIP2_RSP_ERR_NONE &&
boot == PIP2_STATUS_APP_EXEC)
*sys_mode = read_buf[PIP2_RESP_BODY_OFFSET + 1];
else
*sys_mode = FW_SYS_MODE_UNDEFINED;
}
if (mode) {
if (status == PIP2_RSP_ERR_NONE &&
boot == PIP2_STATUS_BOOT_EXEC)
*mode = PT_MODE_BOOTLOADER;
else if (status == PIP2_RSP_ERR_NONE &&
boot == PIP2_STATUS_APP_EXEC)
*mode = PT_MODE_OPERATIONAL;
else
*mode = PT_MODE_UNKNOWN;
}
} else {
if (mode)
*mode = PT_MODE_UNKNOWN;
if (sys_mode)
*sys_mode = FW_SYS_MODE_UNDEFINED;
pt_debug(cd->dev, DL_WARN,
"%s: Mode and sys_mode could not be determined\n",
__func__);
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_get_mode_sysmode
*
* SUMMARY: Protected call to pt_pip2_get_mode_sysmode_ by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
* *mode - pointer to store the retrieved mode
* *sys_mode - pointer to store the FW system mode
******************************************************************************/
static int pt_pip2_get_mode_sysmode(struct pt_core_data *cd,
u8 *mode, u8 *sys_mode)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip2_get_mode_sysmode_(cd, mode, sys_mode);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip2_get_mode_sysmode
*
* SUMMARY: Function pointer included in core_commands struct for external
* calls to the protected or unprotected call to
* pt_pip2_get_mode_sysmode
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *mode - pointer to store the retrieved mode
* *sys_mode - pointer to store the FW system mode
******************************************************************************/
static int _pt_request_pip2_get_mode_sysmode(struct device *dev,
int protect, u8 *mode, u8 *sys_mode)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_pip2_get_mode_sysmode(cd, mode, sys_mode);
return pt_pip2_get_mode_sysmode_(cd, mode, sys_mode);
}
/*******************************************************************************
* FUNCTION: _pt_poll_for_fw_exit_boot_mode
*
* SUMMARY: Verify and or poll for the FW to exit BOOT mode. During the FW BOOT
* mode only the following PIP commands will be serviced, any other PIP
* command the FW will respond with an "Invalid PIP Command" response.
* - Get HID Descriptor (Register 0x0001, no command ID)
* - Reset (Register 0x0005, RESET HID request)
* - Ping (Register 0x0004, Command ID 0x00
* - Get System Information (Register 0x0004, Command ID 0x02)
* - PIP2 Status (Register 0x0101, Command ID 0x01)
* - PIP2 Version (Register 0x0101, Command ID 0x07)
* This function will loop on the results of the STATUS command until
* the FW reports it is out of BOOT mode.
*
* NOTE:
* - This function will update cd->fw_system_mode
* - The STATUS cmd only supports this functionality for PIP 1.11+
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* timeout - max time (ms) to wait for FW to exit BOOT mode
* actual_wait - pointer to actual time waited for FW to exit BOOT mode
******************************************************************************/
static int _pt_poll_for_fw_exit_boot_mode(struct pt_core_data *cd, int timeout,
int *actual_wait)
{
int loop = 0;
u8 sys_mode = cd->fw_system_mode;
u8 pause = 10; /* in ms */
int rc = 0;
int max_loop = (timeout / pause) + 1; /* Add 1 due to int math */
if (cd->sysinfo.ready && !IS_PIP_VER_GE(&cd->sysinfo, 1, 11)) {
/*
* For PIP <1.11, no support for polling wait so do a hard
* coded wait and assume the FW is out of BOOT. Added 1 to
* timeout to make it clear in kmsg if non polling was done.
*/
*actual_wait = PT_FW_EXIT_BOOT_MODE_TIMEOUT + 1;
pt_debug(cd->dev, DL_ERROR,
"%s: PIP %d.%d no support for ext STATUS, sleep %d\n",
__func__,
cd->sysinfo.ttdata.pip_ver_major,
cd->sysinfo.ttdata.pip_ver_minor, *actual_wait);
msleep(*actual_wait);
sys_mode = FW_SYS_MODE_SCANNING;
}
if (sys_mode == FW_SYS_MODE_BOOT) {
while (!rc && loop <= max_loop &&
(sys_mode == FW_SYS_MODE_BOOT)) {
loop++;
usleep_range(9000, pause * 1000);
rc = pt_pip2_get_mode_sysmode_(cd, NULL, &sys_mode);
pt_debug(cd->dev, DL_DEBUG,
"%s: FW in BOOT mode-sleep %dms, sys_mode=%d\n",
__func__, loop * pause, sys_mode);
}
*actual_wait = (int)(loop * pause);
pt_debug(cd->dev, DL_WARN,
"%s: FW exited BOOT mode in %dms, sys_mode=%d\n",
__func__, *actual_wait, sys_mode);
if (rc)
sys_mode = FW_SYS_MODE_UNDEFINED;
else if (sys_mode == FW_SYS_MODE_BOOT ||
sys_mode == FW_SYS_MODE_UNDEFINED)
rc = -EBUSY;
}
mutex_lock(&cd->system_lock);
cd->fw_system_mode = sys_mode;
mutex_unlock(&cd->system_lock);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_poll_for_fw_exit_boot_mode
*
* SUMMARY: Protected call to _pt_poll_for_fw_exit_boot_mode by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* timeout - max time (ms) to wait for FW to exit BOOT mode
* actual_wait - pointer to actual time waited for FW to exit BOOT mode
******************************************************************************/
static int pt_poll_for_fw_exit_boot_mode(struct pt_core_data *cd, int timeout,
int *actual_wait)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = _pt_poll_for_fw_exit_boot_mode(cd, timeout, actual_wait);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_get_fw_sys_mode
*
* SUMMARY: Determine the FW system mode. For PIP 1.11+ the
* PIP2 STATUS command is used to directly query the FW system mode. For older
* PIP versions, there is no direct PIP commamnd that will directly provide this
* information but any PIP command above 0x1F requires scanning to be disabled
* before it will be operational. If scanning was not disabled before sending
* these PIP commands the FW will respond with a 6 byte error response. So to
* safely determine the scanning state, a PIP message that will not affect the
* operation of the FW was chosen:
* "Verify Data Block CRC (ID 0x20)" is sent and if a 6 byte error code is
* received scanning is active.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *sys_mode - pointer to FW System mode
* *mode - pointer to mode (BL/FW)
******************************************************************************/
static int _pt_get_fw_sys_mode(struct pt_core_data *cd, u8 *sys_mode, u8 *mode)
{
int write_length = 1;
int report_length;
int rc = 0;
u8 tmp_sys_mode = FW_SYS_MODE_UNDEFINED;
u8 tmp_mode = PT_MODE_UNKNOWN;
u8 param[1] = { PT_TCH_PARM_EBID };
struct pt_hid_output hid_output = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_VERIFY_CONFIG_BLOCK_CRC),
.write_length = write_length,
.write_buf = param,
.novalidate = true,
};
/* AFter PIP1.11 the preferred method is using STATUS cmd */
if (IS_PIP_VER_GE(&cd->sysinfo, 1, 11)) {
rc = pt_pip2_get_mode_sysmode_(cd, &tmp_mode, &tmp_sys_mode);
pt_debug(cd->dev, DL_DEBUG, "%s: tmp_sys_mode=%d tmp_mode=%d\n",
__func__, tmp_sys_mode, tmp_mode);
if (!rc) {
if (tmp_mode != PT_MODE_OPERATIONAL)
tmp_sys_mode = FW_SYS_MODE_UNDEFINED;
}
goto exit;
}
/* Older systems use PIP1 CONFIG_BLOCK_CRC to best determine sys_mode */
if (cd->mode != PT_MODE_OPERATIONAL) {
tmp_mode = cd->mode;
goto exit;
}
rc = pt_pip1_send_output_and_wait_(cd, &hid_output);
if (rc)
goto exit;
report_length = (cd->response_buf[1] << 8) | (cd->response_buf[0]);
if ((report_length == 0x06) &&
((cd->response_buf[4] & PIP1_RESP_COMMAND_ID_MASK) == 0x00) &&
(cd->response_buf[5] == PIP1_CMD_ID_VERIFY_CONFIG_BLOCK_CRC)) {
tmp_mode = PIP2_STATUS_APP_EXEC;
tmp_sys_mode = FW_SYS_MODE_SCANNING;
} else if ((report_length == 0x0A) &&
((cd->response_buf[4] & PIP1_RESP_COMMAND_ID_MASK) ==
PIP1_CMD_ID_VERIFY_CONFIG_BLOCK_CRC)) {
tmp_mode = PIP2_STATUS_APP_EXEC;
tmp_sys_mode = FW_SYS_MODE_TEST;
}
exit:
if (mode)
*mode = tmp_mode;
if (sys_mode)
*sys_mode = tmp_sys_mode;
pt_debug(cd->dev, DL_INFO, "%s: Return Mode=%d sys_mode=%d\n",
__func__, tmp_mode, tmp_sys_mode);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_get_fw_sys_mode
*
* SUMMARY: Protected call to _pt_get_fw_sys_mode() to determine if FW scanning
* is active or not.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *sys_mode - pointer to fw system mode
* *mode - pointer to mode
******************************************************************************/
static int pt_get_fw_sys_mode(struct pt_core_data *cd, u8 *sys_mode, u8 *mode)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = _pt_get_fw_sys_mode(cd, sys_mode, mode);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_get_fw_sys_mode
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request to get scan state
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
* *sys_mode - pointer to FW system mode
* *mode - pointer to mode
******************************************************************************/
static int _pt_request_get_fw_sys_mode(struct device *dev, int protect,
u8 *sys_mode, u8 *mode)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
if (protect)
return pt_get_fw_sys_mode(cd, sys_mode, mode);
return _pt_get_fw_sys_mode(cd, sys_mode, mode);
}
/* Default hid descriptor to provide basic register map */
const struct pt_hid_desc hid_desc_default = {
230, /* hid_desc_len */
HID_APP_REPORT_ID, /* packet_id */
0x00, /* reserved_byte */
0x0100, /* bcd_version */
0x00EC, /* report_desc_len */
0x0002, /* report_desc_register */
0x0003, /* input_register */
0x00FE, /* max_input_len */
0x0004, /* output_register */
0x00FE, /* max_output_len */
0x0005, /* command_register */
0x0006, /* data_register */
0x04B4, /* vendor_id */
0xC101, /* product_id */
0x0100, /* version_id */
{0x00, 0x00, 0x00, 0x00} /* reserved[4] */
};
/*******************************************************************************
* FUNCTION: pt_init_hid_descriptor
*
* SUMMARY: Setup default values for HID descriptor structure
*
*
* PARAMETERS:
* *desc - pointer to the HID descriptor data read back from DUT
******************************************************************************/
static inline void pt_init_hid_descriptor(struct pt_hid_desc *desc)
{
memcpy(desc, &hid_desc_default, sizeof(hid_desc_default));
}
/*******************************************************************************
* FUNCTION: pt_get_hid_descriptor_
*
* SUMMARY: Send the get HID descriptor command to the DUT and load the response
* into the HID descriptor structure
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *desc - pointer to the HID descriptor data read back from DUT
******************************************************************************/
static int pt_get_hid_descriptor_(struct pt_core_data *cd,
struct pt_hid_desc *desc)
{
struct device *dev = cd->dev;
int rc = 0;
int t;
u8 cmd[2];
/*
* During startup the HID descriptor is required for all future
* processing. If IRQ is already asserted due to an early touch report
* the report must be cleared before sending command.
*/
pt_flush_bus_if_irq_asserted(cd, PT_FLUSH_BUS_BASED_ON_LEN);
/* Read HID descriptor length and version */
mutex_lock(&cd->system_lock);
cd->hid_cmd_state = 1;
mutex_unlock(&cd->system_lock);
/* Set HID descriptor register */
memcpy(cmd, &cd->hid_core.hid_desc_register,
sizeof(cd->hid_core.hid_desc_register));
pt_debug(cd->dev, DL_INFO, ">>> %s: Write Buffer [%zu]",
__func__, sizeof(cmd));
pt_pr_buf(cd->dev, DL_DEBUG, cmd, sizeof(cmd), ">>> Get HID Desc");
rc = pt_adap_write_read_specific(cd, 2, cmd, NULL);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: failed to get HID descriptor, rc=%d\n",
__func__, rc);
goto error;
}
t = wait_event_timeout(cd->wait_q, (cd->hid_cmd_state == 0),
msecs_to_jiffies(PT_GET_HID_DESCRIPTOR_TIMEOUT));
if (IS_TMO(t)) {
#ifdef TTDL_DIAGNOSTICS
cd->bus_transmit_error_count++;
pt_toggle_err_gpio(cd, PT_ERR_GPIO_I2C_TRANS);
#endif /* TTDL_DIAGNOSTICS */
pt_debug(cd->dev, DL_ERROR,
"%s: HID get descriptor timed out\n", __func__);
rc = -ETIME;
goto error;
} else {
cd->hw_detected = true;
}
/* Load the HID descriptor including all registers */
memcpy((u8 *)desc, cd->response_buf, sizeof(struct pt_hid_desc));
/* Check HID descriptor length and version */
pt_debug(dev, DL_INFO, "%s: HID len:%X HID ver:%X\n", __func__,
le16_to_cpu(desc->hid_desc_len),
le16_to_cpu(desc->bcd_version));
if (le16_to_cpu(desc->hid_desc_len) != sizeof(*desc) ||
le16_to_cpu(desc->bcd_version) != HID_VERSION) {
pt_debug(dev, DL_ERROR, "%s: Unsupported HID version\n",
__func__);
return -ENODEV;
}
goto exit;
error:
mutex_lock(&cd->system_lock);
cd->hid_cmd_state = 0;
mutex_unlock(&cd->system_lock);
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_get_hid_descriptor
*
* SUMMARY: Protected call to pt_get_hid_descriptor_()
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *desc - pointer to the HID descriptor data read back from DUT
******************************************************************************/
static int pt_get_hid_descriptor(struct pt_core_data *cd,
struct pt_hid_desc *desc)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_get_hid_descriptor_(cd, desc);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_get_version_
*
* SUMMARY: Sends a PIP2 VERSION command to the DUT and stores the data in
* cd-ttdata
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_pip2_get_version_(struct pt_core_data *cd)
{
int rc = 0;
int status;
u8 read_buf[64];
u16 actual_read_len;
rc = _pt_request_pip2_send_cmd(cd->dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_VERSION,
NULL, 0, read_buf, &actual_read_len);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error Sending PIP2 VERSION Cmd rc=%d\n",
__func__, rc);
return rc;
}
status = read_buf[PIP2_RESP_STATUS_OFFSET];
if (status == 0) {
/* Parse the PIP2 VERSION response into ttdata */
pt_pip2_ver_load_ttdata(cd, actual_read_len);
} else {
pt_debug(cd->dev, DL_ERROR,
"%s: Error in PIP2 VERSION Cmd status=%d\n",
__func__, status);
return status;
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_get_version
*
* SUMMARY: Protected call to pt_pip2_get_version_ by exclusive
* access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_pip2_get_version(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip2_get_version_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_active_pip_protocol
*
* SUMMARY: Get active PIP protocol version using the PIP2 version command.
* Function will return PIP version of BL or application based on
* when it's called.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to run in protected mode
* *pip_version_major - pointer to store PIP major version
* *pip_version_minor - pointer to store PIP minor version
******************************************************************************/
int _pt_request_active_pip_protocol(struct device *dev, int protect,
u8 *pip_version_major, u8 *pip_version_minor)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_ttdata *ttdata = &cd->sysinfo.ttdata;
int rc = 0;
struct pt_hid_output sys_info = {
CREATE_PIP1_FW_CMD(PIP1_CMD_ID_GET_SYSINFO),
.timeout_ms = PT_PIP1_CMD_GET_SYSINFO_TIMEOUT,
};
pt_flush_bus_if_irq_asserted(cd, PT_FLUSH_BUS_BASED_ON_LEN);
/* Skip PIP2 command if DUT generation is confirmed */
if (cd->active_dut_generation == DUT_PIP1_ONLY)
goto skip_pip2_command;
rc = pt_pip2_get_version_(cd);
if (!rc) {
*pip_version_major = ttdata->pip_ver_major;
*pip_version_minor = ttdata->pip_ver_minor;
pt_debug(dev, DL_INFO,
"%s: pip_version = %d.%d\n", __func__,
*pip_version_major, *pip_version_minor);
} else {
/*
* Legacy products do not support the pip2 protocol to get
* pip version. However, they do support the "get sysinfo"
* command to get pip version from FW, but the bootloader
* does not support it. This function will try "get sysinfo"
* command if the pip2 command failed but this cmd could also
* fail if DUT is stuck in bootloader mode.
*/
pt_debug(dev, DL_INFO,
"%s: PIP2 no response rc = %d, try legacy cmd\n",
__func__, rc);
skip_pip2_command:
rc = pt_pip1_send_output_and_wait_(cd, &sys_info);
if (!rc) {
*pip_version_minor =
cd->response_buf[PIP1_SYSINFO_TTDATA_OFFSET + 1];
*pip_version_major =
cd->response_buf[PIP1_SYSINFO_TTDATA_OFFSET];
pt_debug(dev, DL_INFO,
"%s: pip_version = %d.%d\n", __func__,
*pip_version_major, *pip_version_minor);
} else {
*pip_version_major = 0;
*pip_version_minor = 0;
pt_debug(dev, DL_ERROR,
"%s: pip_version Not Detected\n", __func__);
}
}
return rc;
}
EXPORT_SYMBOL_GPL(_pt_request_active_pip_protocol);
/*******************************************************************************
* FUNCTION: _pt_detect_dut_generation
*
* SUMMARY: Determine the generation of device that we are communicating with:
* DUT_PIP1_ONLY (Gen5 or Gen6)
* DUT_PIP2_CAPABLE (TC33xx or TT7xxx)
* The HID_DESC command is supported in Gen5/6 BL and FW as well as
* TT/TC FW. The packet ID in the descriptor, however, is unique when
* coming form the BL or the FW:
* Packet_ID in BL = HID_BL_REPORT_ID (0xFF)
* Packet_ID in FW = HID_APP_REPORT_ID (0xF7)
* This function will return a modified status if it detects the DUT
* is in the BL. In the case of a Gen5/6 BL, which also sends out a FW
* reset sentinel, the status is "corrected" from a FW to BL sentinel.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *status - pointer to status bitmask
* *dut_gen - pointer to store the dut_generation
* *mode - pointer to store the PT_MODE
******************************************************************************/
static int _pt_detect_dut_generation(struct device *dev,
u32 *status, u8 *dut_gen, enum pt_mode *mode)
{
int rc = 0;
u8 dut_gen_tmp = DUT_UNKNOWN;
u8 mode_tmp = PT_MODE_UNKNOWN;
u8 attempt = 1;
u32 status_tmp = STARTUP_STATUS_START;
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_hid_desc hid_desc;
memset(&hid_desc, 0, sizeof(hid_desc));
rc = pt_get_hid_descriptor_(cd, &hid_desc);
while (rc && attempt < 3) {
attempt++;
usleep_range(2000, 5000);
rc = pt_get_hid_descriptor_(cd, &hid_desc);
}
if (!rc && hid_desc.packet_id == HID_BL_REPORT_ID) {
dut_gen_tmp = DUT_PIP1_ONLY; /* Gen5/6 BL */
mode_tmp = PT_MODE_BOOTLOADER;
status_tmp = STARTUP_STATUS_BL_RESET_SENTINEL;
} else if (!rc && hid_desc.packet_id == HID_APP_REPORT_ID) {
rc = pt_pip2_get_version_(cd);
if (!rc)
dut_gen_tmp = DUT_PIP2_CAPABLE; /* TT/TC FW */
else
dut_gen_tmp = DUT_PIP1_ONLY; /* Gen5/6 FW */
mode_tmp = PT_MODE_OPERATIONAL;
status_tmp = STARTUP_STATUS_FW_RESET_SENTINEL;
rc = 0; /* To return success instead of error code */
} else if (rc) {
rc = pt_pip2_get_version_(cd);
if (!rc) {
dut_gen_tmp = DUT_PIP2_CAPABLE; /* TT/TC BL */
mode_tmp = PT_MODE_BOOTLOADER;
status_tmp = STARTUP_STATUS_BL_RESET_SENTINEL;
}
}
mutex_lock(&cd->system_lock);
if (dut_gen)
*dut_gen = dut_gen_tmp;
if (mode)
*mode = mode_tmp;
if (status)
*status = status_tmp;
mutex_unlock(&cd->system_lock);
#ifdef TTDL_DIAGNOSTICS
pt_debug(cd->dev, DL_INFO, "%s: Generation=%d Mode=%d\n",
__func__, dut_gen_tmp, mode_tmp);
#endif /* TTDL_DIAGNOSTICS */
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_dut_generation
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to get current dut generation.
*
* NOTE: This function WILL NOT try to determine dut generation.
*
* RETURN:
* The current dut generation.
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static int _pt_request_dut_generation(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return cd->active_dut_generation;
}
#define HW_VERSION_LEN_MAX 13
/*******************************************************************************
* FUNCTION: _legacy_generate_hw_version
*
* SUMMARY: Format chip information from struct ttdata (maintained by PIP1
* SYSINFO command) or struct bl_info (maintained by PIP1 BL INFORMATION
* command) to the hw_version.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hw_version - pointer to store the hardware version
******************************************************************************/
static int _legacy_generate_hw_version(struct pt_core_data *cd,
char *hw_version)
{
struct pt_ttdata *ttdata = &cd->sysinfo.ttdata;
if (cd->sysinfo.ready) {
scnprintf(hw_version, HW_VERSION_LEN_MAX, "%04X.FFFF.%02X",
ttdata->jtag_id_h, cd->pid_for_loader);
return 0;
} else if (cd->bl_info.ready) {
scnprintf(hw_version, HW_VERSION_LEN_MAX, "%04X.FFFF.%02X",
cd->bl_info.chip_id, cd->pid_for_loader);
return 0;
} else {
snprintf(hw_version, HW_VERSION_LEN_MAX, "FFFF.FFFF.FF");
pt_debug(cd->dev, DL_ERROR,
"%s: SYSINFO and BL_INFO are not ready\n", __func__);
return -ENODATA;
}
}
/*******************************************************************************
* FUNCTION: _pip2_generate_hw_version
*
* SUMMARY: Format chip information from struct ttdata (maintained by PIP2
* VERSION command) to the hw_version.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hw_version - pointer to store the hardware version
******************************************************************************/
static int _pip2_generate_hw_version(struct pt_core_data *cd, char *hw_version)
{
struct pt_ttdata *ttdata = &cd->sysinfo.ttdata;
if (cd->app_pip_ver_ready | cd->bl_pip_ver_ready) {
snprintf(hw_version, HW_VERSION_LEN_MAX, "%04X.%04X.%02X",
ttdata->chip_id, ttdata->chip_rev, cd->pid_for_loader);
return 0;
} else {
snprintf(hw_version, HW_VERSION_LEN_MAX, "FFFF.FFFF.FF");
pt_debug(cd->dev, DL_ERROR,
"%s: PIP Version are not ready\n", __func__);
return -ENODATA;
}
}
/*******************************************************************************
* FUNCTION: pt_generate_hw_version
*
* SUMMARY: Wraaper function for both legacy and TT/TC products generate the
* hw_version from static data.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *hw_version - pointer to store the hardware version
******************************************************************************/
static int pt_generate_hw_version(struct pt_core_data *cd, char *hw_version)
{
int rc = 0;
if (!hw_version)
return -ENOMEM;
if (cd->active_dut_generation == DUT_PIP1_ONLY)
rc = _legacy_generate_hw_version(cd, hw_version);
else if (cd->active_dut_generation == DUT_PIP2_CAPABLE)
rc = _pip2_generate_hw_version(cd, hw_version);
else {
snprintf(hw_version, HW_VERSION_LEN_MAX, "FFFF.FFFF.FF");
rc = -ENODATA;
}
return rc;
}
/*******************************************************************************
* SUMMARY: Attempt to retrieve the HW version of the connected DUT
*
* NOTE: The calling function must ensure to free *hw_version
*
* RETURN:
* 0 = success
* !0 = Failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *hw_version - pointer to where the hw_version string will be stored
******************************************************************************/
static int _pt_request_hw_version(struct device *dev, char *hw_version)
{
int rc = 0;
u16 actual_read_len;
u16 pip_ver;
u8 rd_buf[256];
u8 status;
u8 index = PIP2_RESP_STATUS_OFFSET;
u8 return_data[8];
u8 panel_id;
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_ttdata *ttdata = &cd->sysinfo.ttdata;
if (!hw_version)
return -ENOMEM;
if (!cd->hw_detected) {
/* No HW detected */
rc = -ENODEV;
pt_debug(dev, DL_ERROR, "%s: no hardware is detected!\n",
__func__);
goto exit_error;
}
memset(return_data, 0, ARRAY_SIZE(return_data));
/* For Parade TC or TT parts */
if (cd->active_dut_generation == DUT_PIP2_CAPABLE) {
rc = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_VERSION,
NULL, 0, rd_buf, &actual_read_len);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: Failed to send PIP2 VERSION cmd\n",
__func__);
goto exit_error;
}
status = rd_buf[index];
if (status == 0) {
pip_ver = 256 * rd_buf[index + 2] + rd_buf[index + 1];
/*
* BL PIP 2.02 and greater the version fields are
* swapped
*/
if (pip_ver >= 0x0202) {
snprintf(hw_version, HW_VERSION_LEN_MAX,
"%02X%02X.%02X%02X.FF",
rd_buf[index + 10], rd_buf[index + 9],
rd_buf[index + 8], rd_buf[index + 7]);
} else {
snprintf(hw_version, HW_VERSION_LEN_MAX,
"%02X%02X.%02X%02X.FF",
rd_buf[index + 8], rd_buf[index + 7],
rd_buf[index + 10], rd_buf[index + 9]);
}
return STATUS_SUCCESS;
} else {
rc = status;
pt_debug(dev, DL_WARN,
"%s: PIP2 VERSION cmd response error\n",
__func__);
}
} else if (cd->active_dut_generation == DUT_PIP1_ONLY) {
/*
* For Parade/Cypress legacy parts the RevID and FamilyID are
* hard coded to FFFF
*/
if (cd->mode == PT_MODE_OPERATIONAL) {
rc = pt_hid_output_get_sysinfo(cd);
if (!rc) {
panel_id =
cd->sysinfo.sensing_conf_data.panel_id;
} else {
panel_id = PANEL_ID_NOT_ENABLED;
}
/* In FW - simply retrieve from ttdata struct */
snprintf(hw_version, HW_VERSION_LEN_MAX,
"%04X.FFFF.%02X",
ttdata->jtag_id_h,
panel_id);
return STATUS_SUCCESS;
} else {
/*
* Return the stored value if PT_PANEL_ID_BY_BL
* is not supported while other feature is.
*/
if (cd->panel_id_support & PT_PANEL_ID_BY_BL) {
rc = pt_hid_output_bl_get_information(
cd, return_data);
if (!rc) {
rc = pt_hid_output_bl_get_panel_id(
cd, &panel_id);
}
} else
panel_id = cd->pid_for_loader;
if (!rc) {
snprintf(hw_version,
HW_VERSION_LEN_MAX,
"%02X%02X.FFFF.%02X",
return_data[3], return_data[2],
panel_id);
return STATUS_SUCCESS;
}
}
} else {
/* Unknown generation */
rc = -ENODEV;
pt_debug(dev, DL_ERROR, "%s: generation is unknown!\n",
__func__);
}
exit_error:
snprintf(hw_version, HW_VERSION_LEN_MAX, "FFFF.FFFF.FF");
return rc;
}
/*******************************************************************************
* FUNCTION: pt_start_wd_timer
*
* SUMMARY: Starts the TTDL watchdog timer if the timer interval is > 0
*
* RETURN: void
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_start_wd_timer(struct pt_core_data *cd)
{
if (cd->watchdog_interval < 100) {
pt_debug(cd->dev, DL_ERROR,
"%s: WARNING: Invalid watchdog interval: %d\n",
__func__, cd->watchdog_interval);
return;
}
if (cd->watchdog_force_stop) {
pt_debug(cd->dev, DL_INFO,
"%s: TTDL WD Forced stop\n", __func__);
return;
}
mod_timer(&cd->watchdog_timer, jiffies +
msecs_to_jiffies(cd->watchdog_interval));
cd->watchdog_enabled = 1;
pt_debug(cd->dev, DL_INFO, "%s: TTDL WD Started\n", __func__);
}
/*******************************************************************************
* FUNCTION: pt_stop_wd_timer
*
* SUMMARY: Stops the TTDL watchdog timer if the timer interval is > 0
*
* RETURN: void
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_stop_wd_timer(struct pt_core_data *cd)
{
if (!cd->watchdog_interval)
return;
/*
* Ensure we wait until the watchdog timer
* running on a different CPU finishes
*/
del_timer_sync(&cd->watchdog_timer);
cancel_work_sync(&cd->watchdog_work);
del_timer_sync(&cd->watchdog_timer);
cd->watchdog_enabled = 0;
pt_debug(cd->dev, DL_INFO, "%s: TTDL WD Stopped\n", __func__);
}
/*******************************************************************************
* FUNCTION: pt_hw_soft_reset
*
* SUMMARY: Sends a PIP reset command to the DUT. Disable/re-enable the
* TTDL watchdog around the reset to ensure the WD doesn't happen to
* schedule an enum if it fires when the DUT is being reset.
* This can cause a double reset.
*
* NOTE: The WD MUST be stopped/restarted by the calling Function. Having
* the WD active could cause this function to fail!
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data struct
* protect - flag to call protected or non-protected
******************************************************************************/
static int pt_hw_soft_reset(struct pt_core_data *cd, int protect)
{
int rc = 0;
mutex_lock(&cd->system_lock);
cd->startup_status = STARTUP_STATUS_START;
pt_debug(cd->dev, DL_DEBUG, "%s: Startup Status Reset\n", __func__);
mutex_unlock(&cd->system_lock);
if (protect)
rc = pt_hid_cmd_reset(cd);
else
rc = pt_hid_cmd_reset_(cd);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: FAILED to execute SOFT reset\n", __func__);
return rc;
}
pt_debug(cd->dev, DL_INFO, "%s: SOFT reset successful\n",
__func__);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_hw_hard_reset
*
* SUMMARY: Calls the platform xres function if it exists to perform a hard
* reset on the DUT by toggling the XRES gpio. Disable/re-enable the
* TTDL watchdog around the reset to ensure the WD doesn't happen to
* schedule an enum if it fires when the DUT is being reset.
* This can cause a double reset.
*
* NOTE: The WD MUST be stopped/restarted by the calling Function. Having
* the WD active could cause this function to fail!
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data struct
******************************************************************************/
static int pt_hw_hard_reset(struct pt_core_data *cd)
{
if (cd->cpdata->xres) {
cd->startup_status = STARTUP_STATUS_START;
pt_debug(cd->dev, DL_DEBUG, "%s: Startup Status Reset\n",
__func__);
cd->cpdata->xres(cd->cpdata, cd->dev);
pt_debug(cd->dev, DL_WARN, "%s: executed HARD reset\n",
__func__);
return 0;
}
pt_debug(cd->dev, DL_ERROR,
"%s: FAILED to execute HARD reset\n", __func__);
return -ENODEV;
}
/*******************************************************************************
* FUNCTION: pt_dut_reset
*
* SUMMARY: Attempts to reset the DUT by a hard reset and if that fails a
* soft reset.
*
* NOTE: The WD MUST be stopped/restarted by the calling Function. Having
* the WD active could cause this function to fail!
* NOTE: "protect" flag is only used for soft reset.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
* protect - flag to call protected or non-protected
******************************************************************************/
static int pt_dut_reset(struct pt_core_data *cd, int protect)
{
int rc = 0;
pt_debug(cd->dev, DL_INFO, "%s: reset hw...\n", __func__);
mutex_lock(&cd->system_lock);
cd->hid_reset_cmd_state = 1;
rc = pt_hw_hard_reset(cd);
mutex_unlock(&cd->system_lock);
if (rc == -ENODEV) {
mutex_lock(&cd->system_lock);
cd->hid_reset_cmd_state = 0;
mutex_unlock(&cd->system_lock);
pt_debug(cd->dev, DL_ERROR,
"%s: Hard reset failed, try soft reset\n", __func__);
rc = pt_hw_soft_reset(cd, protect);
}
if (rc)
pt_debug(cd->dev, DL_ERROR, "%s: %s dev='%s' r=%d\n",
__func__, "Fail hw reset", dev_name(cd->dev), rc);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_dut_reset_and_wait
*
* SUMMARY: Wrapper function for pt_dut_reset that waits for the reset to
* complete
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int pt_dut_reset_and_wait(struct pt_core_data *cd)
{
int rc = 0;
int t;
rc = pt_dut_reset(cd, PT_CORE_CMD_UNPROTECTED);
if (rc < 0)
goto exit;
t = wait_event_timeout(cd->wait_q,
(cd->hid_reset_cmd_state == 0),
msecs_to_jiffies(PT_HID_CMD_DEFAULT_TIMEOUT));
if (IS_TMO(t)) {
#ifdef TTDL_DIAGNOSTICS
cd->bus_transmit_error_count++;
pt_toggle_err_gpio(cd, PT_ERR_GPIO_I2C_TRANS);
#endif /* TTDL_DIAGNOSTICS */
pt_debug(cd->dev, DL_ERROR, "%s: reset timed out\n",
__func__);
rc = -ETIME;
goto exit;
}
exit:
return rc;
}
/*
* touch default parameters (from report descriptor) to resolve protocol for
* touch report
*/
const struct pt_tch_abs_params tch_hdr_default[PT_TCH_NUM_HDR] = {
/* byte offset, size, min, max, bit offset, report */
{0x00, 0x02, 0x00, 0x10000, 0x00, 0x01}, /* SCAN TIME */
{0x02, 0x01, 0x00, 0x20, 0x00, 0x01}, /* NUMBER OF RECORDS */
{0x02, 0x01, 0x00, 0x02, 0x05, 0x01}, /* LARGE OBJECT */
{0x03, 0x01, 0x00, 0x08, 0x00, 0x01}, /* NOISE EFFECT */
{0x03, 0x01, 0x00, 0x04, 0x06, 0x01}, /* REPORT_COUNTER */
};
/*
* button default parameters (from report descriptor) to resolve protocol for
* button report
*/
const struct pt_tch_abs_params tch_abs_default[PT_TCH_NUM_ABS] = {
/* byte offset, size, min, max, bit offset, report */
{0x02, 0x02, 0x00, 0x10000, 0x00, 0x01}, /* X */
{0x04, 0x02, 0x00, 0x10000, 0x00, 0x01}, /* Y */
{0x06, 0x01, 0x00, 0x100, 0x00, 0x01}, /* P (Z) */
{0x01, 0x01, 0x00, 0x20, 0x00, 0x01}, /* TOUCH ID */
{0x01, 0x01, 0x00, 0x04, 0x05, 0x01}, /* EVENT ID */
{0x00, 0x01, 0x00, 0x08, 0x00, 0x01}, /* OBJECT ID */
{0x01, 0x01, 0x00, 0x02, 0x07, 0x01}, /* LIFTOFF */
{0x07, 0x01, 0x00, 0x100, 0x00, 0x01}, /* TOUCH_MAJOR */
{0x08, 0x01, 0x00, 0x100, 0x00, 0x01}, /* TOUCH_MINOR */
{0x09, 0x01, 0x00, 0x100, 0x00, 0x01}, /* ORIENTATION */
};
/*******************************************************************************
* FUNCTION: pt_init_pip_report_fields
*
* SUMMARY: Setup default values for touch/button report parsing.
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static void pt_init_pip_report_fields(struct pt_core_data *cd)
{
struct pt_sysinfo *si = &cd->sysinfo;
memcpy(si->tch_hdr, tch_hdr_default, sizeof(tch_hdr_default));
memcpy(si->tch_abs, tch_abs_default, sizeof(tch_abs_default));
si->desc.tch_report_id = PT_PIP_TOUCH_REPORT_ID;
si->desc.tch_record_size = TOUCH_REPORT_SIZE;
si->desc.tch_header_size = TOUCH_INPUT_HEADER_SIZE;
si->desc.btn_report_id = PT_PIP_CAPSENSE_BTN_REPORT_ID;
cd->features.easywake = 1;
cd->features.noise_metric = 1;
cd->features.tracking_heatmap = 1;
cd->features.sensor_data = 1;
}
/*******************************************************************************
* FUNCTION: pt_get_mode
*
* SUMMARY: Determine the current mode from the contents of a HID descriptor
* message
*
* RETURN: Enum of the current mode
*
* PARAMETERS:
* *cd - pointer to the Core Data structure
* protect - run command in protected mode
* *mode - pointer to store the retrieved mode
******************************************************************************/
static int pt_get_mode(struct pt_core_data *cd, struct pt_hid_desc *desc)
{
if (desc->packet_id == HID_APP_REPORT_ID)
return PT_MODE_OPERATIONAL;
else if (desc->packet_id == HID_BL_REPORT_ID)
return PT_MODE_BOOTLOADER;
return PT_MODE_UNKNOWN;
}
/*******************************************************************************
* FUNCTION: _pt_request_get_mode
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to determine the current mode of the DUT by use of the Get HID
* Descriptor command.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - run command in protected mode
* *mode - pointer to store the retrieved mode
******************************************************************************/
static int _pt_request_get_mode(struct device *dev, int protect, u8 *mode)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_hid_desc hid_desc;
int rc = 0;
memset(&hid_desc, 0, sizeof(hid_desc));
if (protect)
rc = pt_get_hid_descriptor(cd, &hid_desc);
else
rc = pt_get_hid_descriptor_(cd, &hid_desc);
if (rc)
*mode = PT_MODE_UNKNOWN;
else
*mode = pt_get_mode(cd, &hid_desc);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_queue_enum_
*
* SUMMARY: Queues a TTDL enum by scheduling work with the pt_enum_with_dut()
* function. It won't try to add/delete sysfs node or modules.
*
* RETURN: void
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_queue_enum_(struct pt_core_data *cd)
{
if (cd->startup_state == STARTUP_NONE) {
cd->startup_state = STARTUP_QUEUED;
#ifdef TTDL_DIAGNOSTICS
if (!cd->bridge_mode)
schedule_work(&cd->enum_work);
else
cd->startup_state = STARTUP_NONE;
#else
schedule_work(&cd->enum_work);
#endif
pt_debug(cd->dev, DL_INFO,
"%s: enum_work queued\n", __func__);
} else {
pt_debug(cd->dev, DL_WARN,
"%s: Enum not queued - startup_state = %d\n",
__func__, cd->startup_state);
}
}
/*******************************************************************************
* FUNCTION: pt_queue_enum
*
* SUMMARY: Queues a TTDL enum within a mutex lock
*
* RETURN: void
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_queue_enum(struct pt_core_data *cd)
{
mutex_lock(&cd->system_lock);
pt_queue_enum_(cd);
mutex_unlock(&cd->system_lock);
}
static void remove_sysfs_and_modules(struct device *dev);
/*******************************************************************************
* FUNCTION: pt_queue_restart
*
* SUMMARY: Queues a TTDL restart within a mutex lock
*
* RETURN: void
*
* PARAMETERS:
* *cd - pointer to core data
* remove_sysfs_module - True: remove all DUT relative sysfs nodes and modules
* False: will not perform remove action
******************************************************************************/
static void pt_queue_restart(struct pt_core_data *cd)
{
mutex_lock(&cd->system_lock);
if (cd->startup_state == STARTUP_NONE) {
cd->startup_state = STARTUP_QUEUED;
schedule_work(&cd->ttdl_restart_work);
pt_debug(cd->dev, DL_INFO,
"%s: pt_ttdl_restart queued\n", __func__);
} else {
pt_debug(cd->dev, DL_INFO, "%s: startup_state = %d\n",
__func__, cd->startup_state);
}
mutex_unlock(&cd->system_lock);
}
/*******************************************************************************
* FUNCTION: call_atten_cb
*
* SUMMARY: Iterate over attention list call the function that registered.
*
* RETURN: void
*
* PARAMETERS:
* *cd - pointer to core data
* type - type of attention list
* mode - condition for execution
******************************************************************************/
static void call_atten_cb(struct pt_core_data *cd,
enum pt_atten_type type, int mode)
{
struct atten_node *atten, *atten_n;
pt_debug(cd->dev, DL_DEBUG, "%s: check list type=%d mode=%d\n",
__func__, type, mode);
spin_lock(&cd->spinlock);
list_for_each_entry_safe(atten, atten_n,
&cd->atten_list[type], node) {
if (!mode || atten->mode & mode) {
spin_unlock(&cd->spinlock);
pt_debug(cd->dev, DL_DEBUG,
"%s: attention for '%s'",
__func__, dev_name(atten->dev));
atten->func(atten->dev);
spin_lock(&cd->spinlock);
}
}
spin_unlock(&cd->spinlock);
}
/*******************************************************************************
* FUNCTION: start_fw_upgrade
*
* SUMMARY: Calling "PT_ATTEN_LOADER" attention list that loader registered to
* start firmware upgrade.
*
* RETURN:
* 0 = success
*
* PARAMETERS:
* *data - pointer to core data
******************************************************************************/
static int start_fw_upgrade(void *data)
{
struct pt_core_data *cd = (struct pt_core_data *)data;
call_atten_cb(cd, PT_ATTEN_LOADER, 0);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_put_device_into_easy_wakeup_
*
* SUMMARY: Call the enter_easywake_state function and set the device into easy
* wake up state.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_put_device_into_easy_wakeup_(struct pt_core_data *cd)
{
int rc = 0;
u8 status = 0;
rc = pt_hid_output_enter_easywake_state_(cd,
cd->easy_wakeup_gesture, &status);
if (rc || status == 0)
return -EBUSY;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_put_device_into_deep_sleep_
*
* SUMMARY: Call the set_power function and set the DUT to deep sleep
*
* RETURN:
* 0 = success
* !0 = error
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_put_device_into_deep_sleep_(struct pt_core_data *cd)
{
int rc = 0;
rc = pt_hid_cmd_set_power_(cd, HID_POWER_SLEEP);
if (rc)
rc = -EBUSY;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_put_device_into_deep_standby_
*
* SUMMARY: Call the set_power function and set the DUT to Deep Standby
*
* RETURN:
* 0 = success
* !0 = error
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_put_device_into_deep_standby_(struct pt_core_data *cd)
{
int rc = 0;
rc = pt_hid_cmd_set_power_(cd, HID_POWER_STANDBY);
if (rc)
rc = -EBUSY;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_poweroff_device_
*
* SUMMARY: Disable IRQ and HW power down the device.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_poweroff_device_(struct pt_core_data *cd)
{
int rc;
if (cd->irq_enabled) {
cd->irq_enabled = false;
disable_irq_nosync(cd->irq);
}
rc = cd->cpdata->power(cd->cpdata, 0, cd->dev, 0);
if (rc < 0)
pt_debug(cd->dev, DL_ERROR, "%s: HW Power down fails r=%d\n",
__func__, rc);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_sleep_
*
* SUMMARY: Suspend the device with power off or deep sleep based on the
* configuration in the core platform data structure.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_sleep_(struct pt_core_data *cd)
{
int rc = 0;
mutex_lock(&cd->system_lock);
pt_debug(cd->dev, DL_INFO, "%s - sleep_state %d\n", __func__, cd->sleep_state);
if (cd->sleep_state == SS_SLEEP_ON || cd->sleep_state == SS_SLEEPING) {
mutex_unlock(&cd->system_lock);
pt_debug(cd->dev, DL_INFO,
"%s - Skip slee[ state %d\n", __func__, cd->sleep_state);
return 0;
} else {
cd->sleep_state = SS_SLEEPING;
}
mutex_unlock(&cd->system_lock);
/* Ensure watchdog and startup works stopped */
pt_stop_wd_timer(cd);
cancel_work_sync(&cd->enum_work);
pt_stop_wd_timer(cd);
if (cd->cpdata->flags & PT_CORE_FLAG_POWEROFF_ON_SLEEP) {
pt_debug(cd->dev, DL_INFO, "%s: Entering into power off mode:\n", __func__);
rc = pt_core_poweroff_device_(cd);
if (rc)
pr_err("%s: Power off error detected :rc=%d\n", __func__, rc);
} else if (cd->cpdata->flags & PT_CORE_FLAG_DEEP_STANDBY) {
pt_debug(cd->dev, DL_INFO,
"%s: Entering into deep standby mode:\n", __func__);
rc = pt_put_device_into_deep_standby_(cd);
if (rc)
pr_err("%s: Deep standby error detected :rc=%d\n", __func__, rc);
} else {
pt_debug(cd->dev, DL_INFO,
"%s: Entering into deep sleep mode:\n", __func__);
rc = pt_put_device_into_deep_sleep_(cd);
if (rc)
pr_err("%s: Deep sleep error detected :rc=%d\n", __func__, rc);
}
mutex_lock(&cd->system_lock);
cd->sleep_state = SS_SLEEP_ON;
mutex_unlock(&cd->system_lock);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_easywake_on_
*
* SUMMARY: Suspend the device with easy wake on the
* configuration in the core platform data structure.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_easywake_on_(struct pt_core_data *cd)
{
int rc = 0;
mutex_lock(&cd->system_lock);
if (cd->sleep_state == SS_EASY_WAKING_ON) {
mutex_unlock(&cd->system_lock);
pt_debug(cd->dev, DL_INFO, "%s - Skip sleep state %d\n",
__func__, cd->sleep_state);
return 0;
}
mutex_unlock(&cd->system_lock);
/* Ensure watchdog and startup works stopped */
pt_stop_wd_timer(cd);
cancel_work_sync(&cd->enum_work);
pt_stop_wd_timer(cd);
if (IS_EASY_WAKE_CONFIGURED(cd->easy_wakeup_gesture)) {
rc = pt_put_device_into_easy_wakeup_(cd);
pt_debug(cd->dev, DL_INFO, "%s :Entering into easywakeup: rc=%d\n", __func__, rc);
if (rc)
pr_err("%s: Easy wakeup error detected :rc=%d\n", __func__, rc);
}
mutex_lock(&cd->system_lock);
cd->sleep_state = SS_EASY_WAKING_ON;
mutex_unlock(&cd->system_lock);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_easywake_on
*
* SUMMARY: Protected call to pt_core_easywake_on_ by exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_easywake_on(struct pt_core_data *cd)
{
int rc = 0;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_core_easywake_on_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
else
pt_debug(cd->dev, DL_DEBUG, "%s: pass release exclusive\n",
__func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_sleep
*
* SUMMARY: Protected call to pt_core_sleep_ by exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_sleep(struct pt_core_data *cd)
{
int rc = 0;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_core_sleep_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
else
pt_debug(cd->dev, DL_DEBUG, "%s: pass release exclusive\n",
__func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_wakeup_host
*
* SUMMARY: Check wake up report and call the PT_ATTEN_WAKE attention list.
*
* NOTE: TSG5 EasyWake and TSG6 EasyWake use different protocol.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_wakeup_host(struct pt_core_data *cd)
{
#ifndef EASYWAKE_TSG6
/* TSG5 EasyWake */
int rc = 0;
int event_id;
int size = get_unaligned_le16(&cd->input_buf[0]);
/* Validate report */
if (size != 4 || cd->input_buf[2] != 4)
rc = -EINVAL;
event_id = cd->input_buf[3];
pt_debug(cd->dev, DL_INFO, "%s: e=%d, rc=%d\n",
__func__, event_id, rc);
if (rc) {
pt_core_sleep_(cd);
goto exit;
}
/* attention WAKE */
call_atten_cb(cd, PT_ATTEN_WAKE, 0);
exit:
return rc;
#else
/* TSG6 FW1.3 EasyWake */
int rc = 0;
int i = 0;
int report_length;
/* Validate report */
if (cd->input_buf[2] != PT_PIP_WAKEUP_REPORT_ID) {
rc = -EINVAL;
pt_core_sleep_(cd);
goto exit;
}
/* Get gesture id and gesture data length */
cd->gesture_id = cd->input_buf[3];
report_length = (cd->input_buf[1] << 8) | (cd->input_buf[0]);
cd->gesture_data_length = report_length - 4;
pt_debug(cd->dev, DL_INFO,
"%s: gesture_id = %d, gesture_data_length = %d\n",
__func__, cd->gesture_id, cd->gesture_data_length);
for (i = 0; i < cd->gesture_data_length; i++)
cd->gesture_data[i] = cd->input_buf[4 + i];
/* attention WAKE */
call_atten_cb(cd, PT_ATTEN_WAKE, 0);
exit:
return rc;
#endif
}
/*******************************************************************************
* FUNCTION: pt_get_touch_axis
*
* SUMMARY: Function to calculate touch axis
*
* PARAMETERS:
* *cd - pointer to core data structure
* *axis - pointer to axis calculation result
* size - size in bytes
* max - max value of result
* *xy_data - pointer to input data to be parsed
* bofs - bit offset
******************************************************************************/
static void pt_get_touch_axis(struct pt_core_data *cd,
int *axis, int size, int max, u8 *data, int bofs)
{
int nbyte;
int next;
for (nbyte = 0, *axis = 0, next = 0; nbyte < size; nbyte++) {
*axis = *axis + ((data[next] >> bofs) << (nbyte * 8));
next++;
}
*axis &= max - 1;
}
/*******************************************************************************
* FUNCTION: move_tracking_heatmap_data
*
* SUMMARY: Move the valid tracking heatmap data from the input buffer into the
* system information structure, xy_mode and xy_data.
* - If TTHE_TUNER_SUPPORT is defined print the raw sensor data into
* the tthe_tuner sysfs node under the label "THM"
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *si - pointer to the system information structure
******************************************************************************/
static int move_tracking_heatmap_data(struct pt_core_data *cd,
struct pt_sysinfo *si)
{
#ifdef TTHE_TUNER_SUPPORT
int size = get_unaligned_le16(&cd->input_buf[0]);
if (size)
tthe_print(cd, cd->input_buf, size, "THM=");
#endif
memcpy(si->xy_mode, cd->input_buf, SENSOR_HEADER_SIZE);
return 0;
}
/*******************************************************************************
* FUNCTION: move_sensor_data
*
* SUMMARY: Move the valid sensor data from the input buffer into the system
* information structure, xy_mode and xy_data.
* - If TTHE_TUNER_SUPPORT is defined print the raw sensor data into
* the tthe_tuner sysfs node under the label "sensor_monitor"
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *si - pointer to the system information structure
******************************************************************************/
static int move_sensor_data(struct pt_core_data *cd,
struct pt_sysinfo *si)
{
#ifdef TTHE_TUNER_SUPPORT
int size = get_unaligned_le16(&cd->input_buf[0]);
if (size)
tthe_print(cd, cd->input_buf, size, "sensor_monitor=");
#endif
memcpy(si->xy_mode, cd->input_buf, SENSOR_HEADER_SIZE);
return 0;
}
/*******************************************************************************
* FUNCTION: move_button_data
*
* SUMMARY: Move the valid button data from the input buffer into the system
* information structure, xy_mode and xy_data.
* - If TTHE_TUNER_SUPPORT is defined print the raw button data into
* the tthe_tuner sysfs node under the label "OpModeData"
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *si - pointer to the system information structure
******************************************************************************/
static int move_button_data(struct pt_core_data *cd,
struct pt_sysinfo *si)
{
#ifdef TTHE_TUNER_SUPPORT
int size = get_unaligned_le16(&cd->input_buf[0]);
if (size)
tthe_print(cd, cd->input_buf, size, "OpModeData=");
#endif
memcpy(si->xy_mode, cd->input_buf, BTN_INPUT_HEADER_SIZE);
pt_pr_buf(cd->dev, DL_INFO, (u8 *)si->xy_mode, BTN_INPUT_HEADER_SIZE,
"xy_mode");
memcpy(si->xy_data, &cd->input_buf[BTN_INPUT_HEADER_SIZE],
BTN_REPORT_SIZE);
pt_pr_buf(cd->dev, DL_INFO, (u8 *)si->xy_data, BTN_REPORT_SIZE,
"xy_data");
return 0;
}
/*******************************************************************************
* FUNCTION: move_touch_data
*
* SUMMARY: Move the valid touch data from the input buffer into the system
* information structure, xy_mode and xy_data.
* - If TTHE_TUNER_SUPPORT is defined print the raw touch data into
* the tthe_tuner sysfs node under the label "OpModeData"
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *si - pointer to the system information structure
******************************************************************************/
static int move_touch_data(struct pt_core_data *cd, struct pt_sysinfo *si)
{
int max_tch = si->sensing_conf_data.max_tch;
int num_cur_tch;
int length;
struct pt_tch_abs_params *tch = &si->tch_hdr[PT_TCH_NUM];
#ifdef TTHE_TUNER_SUPPORT
int size = get_unaligned_le16(&cd->input_buf[0]);
if (size)
tthe_print(cd, cd->input_buf, size, "OpModeData=");
#endif
memcpy(si->xy_mode, cd->input_buf, si->desc.tch_header_size);
pt_pr_buf(cd->dev, DL_INFO, (u8 *)si->xy_mode,
si->desc.tch_header_size, "xy_mode");
pt_get_touch_axis(cd, &num_cur_tch, tch->size,
tch->max, si->xy_mode + 3 + tch->ofs, tch->bofs);
if (unlikely(num_cur_tch > max_tch))
num_cur_tch = max_tch;
length = num_cur_tch * si->desc.tch_record_size;
memcpy(si->xy_data, &cd->input_buf[si->desc.tch_header_size], length);
pt_pr_buf(cd->dev, DL_INFO, (u8 *)si->xy_data, length, "xy_data");
return 0;
}
/*******************************************************************************
* FUNCTION: move_hid_pen_data
*
* SUMMARY: TODO Move the valid pen data from the input buffer into the system
* information structure, xy_mode and xy_data.
* - If TTHE_TUNER_SUPPORT is defined print the raw pen data into
* the tthe_tuner sysfs node under the label "HID" starting with the
* report ID.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *si - pointer to the system information structure
******************************************************************************/
static int move_hid_pen_data(struct pt_core_data *cd, struct pt_sysinfo *si)
{
#ifdef TTHE_TUNER_SUPPORT
int size = get_unaligned_le16(&cd->input_buf[0]);
if (size) {
/*
* HID over USB does not require the two byte length field, so
* this should print from input_buf[2] but to keep both finger
* and pen reports the same the length is included
*/
if (cd->tthe_hid_usb_format == PT_FEATURE_ENABLE)
tthe_print(cd, &(cd->input_buf[2]), size - 2,
"HID-USB=");
else
tthe_print(cd, &(cd->input_buf[0]), size,
"HID-I2C=");
}
#endif
pt_pr_buf(cd->dev, DL_INFO, (u8 *)&(cd->input_buf[0]), size, "HID Pen");
return 0;
}
/*******************************************************************************
* FUNCTION: parse_touch_input
*
* SUMMARY: Parse the touch report and take action based on the touch
* report_id.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* size - size of touch record
******************************************************************************/
static int parse_touch_input(struct pt_core_data *cd, int size)
{
struct pt_sysinfo *si = &cd->sysinfo;
int report_id = cd->input_buf[2];
int rc = -EINVAL;
pt_debug(cd->dev, DL_DEBUG, "%s: Received touch report\n",
__func__);
if (!si->ready) {
pt_debug(cd->dev, DL_ERROR,
"%s: Need system information to parse touches\n",
__func__);
return 0;
}
if (!si->xy_mode || !si->xy_data)
return rc;
if (report_id == PT_PIP_TOUCH_REPORT_ID)
rc = move_touch_data(cd, si);
else if (report_id == PT_HID_PEN_REPORT_ID)
rc = move_hid_pen_data(cd, si);
else if (report_id == PT_PIP_CAPSENSE_BTN_REPORT_ID)
rc = move_button_data(cd, si);
else if (report_id == PT_PIP_SENSOR_DATA_REPORT_ID)
rc = move_sensor_data(cd, si);
else if (report_id == PT_PIP_TRACKING_HEATMAP_REPORT_ID)
rc = move_tracking_heatmap_data(cd, si);
if (rc)
return rc;
/* attention IRQ */
call_atten_cb(cd, PT_ATTEN_IRQ, cd->mode);
return 0;
}
/*******************************************************************************
* FUNCTION: parse_command_input
*
* SUMMARY: Move the response data from the input buffer to the response buffer
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* size - size of response data
******************************************************************************/
static int parse_command_input(struct pt_core_data *cd, int size)
{
pt_debug(cd->dev, DL_DEBUG, "%s: Received cmd interrupt\n",
__func__);
memcpy(cd->response_buf, cd->input_buf, size);
#if defined(TTHE_TUNER_SUPPORT) && defined(TTDL_DIAGNOSTICS)
if (size && cd->show_tt_data) {
if (cd->pip2_prot_active)
tthe_print(cd, cd->input_buf, size, "TT_DATA_PIP2=");
else
tthe_print(cd, cd->input_buf, size, "TT_DATA=");
}
#endif
mutex_lock(&cd->system_lock);
cd->hid_cmd_state = 0;
mutex_unlock(&cd->system_lock);
wake_up(&cd->wait_q);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_allow_enumeration
*
* SUMMARY: Determine if an enumeration or fully re-probe should perform when
* FW sentinel is seen.
*
* RETURN:
* true = allow enumeration or fully re-probe
* false = skip enumeration and fully re-probe
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static inline bool pt_allow_enumeration(struct pt_core_data *cd)
{
if ((cd->panel_id_support & PT_PANEL_ID_BY_SYS_INFO) &&
(!cd->hid_reset_cmd_state) &&
(cd->core_probe_complete) &&
(cd->hid_cmd_state != PIP1_CMD_ID_START_BOOTLOADER + 1) &&
(cd->hid_cmd_state != PIP1_BL_CMD_ID_LAUNCH_APP + 1) &&
(cd->mode == PT_MODE_OPERATIONAL)) {
return true;
}
if ((!cd->hid_reset_cmd_state) &&
(cd->core_probe_complete) &&
(cd->hid_cmd_state != PIP1_CMD_ID_START_BOOTLOADER + 1) &&
(cd->hid_cmd_state != PIP1_BL_CMD_ID_LAUNCH_APP + 1) &&
(cd->active_dut_generation != DUT_PIP1_ONLY)) {
return true;
}
pt_debug(cd->dev, DL_INFO,
"%s: Dissallow - %s=%d %s=%d %s=0x%02X %s=%d\n",
__func__,
"hid_reset_cmd_state(0)", cd->hid_reset_cmd_state,
"core_probe_complete(1)", cd->core_probe_complete,
"hid_cmd_state(Not 0x02 or 0x39)", cd->hid_cmd_state,
"active_dut_gen(0,2)", cd->active_dut_generation);
return false;
}
/*******************************************************************************
* FUNCTION: pt_is_touch_report
*
* SUMMARY: Determine if a report ID should be treated as a touch report
*
* RETURN:
* true = report ID is a touch report
* false = report ID is not a touch report
*
* PARAMETERS:
* id - Report ID
******************************************************************************/
static bool pt_is_touch_report(int id)
{
if (id == PT_PIP_TOUCH_REPORT_ID ||
id == PT_HID_PEN_REPORT_ID ||
id == PT_PIP_CAPSENSE_BTN_REPORT_ID ||
id == PT_PIP_SENSOR_DATA_REPORT_ID ||
id == PT_PIP_TRACKING_HEATMAP_REPORT_ID)
return true;
else
return false;
}
/*******************************************************************************
* FUNCTION: pt_parse_input
*
* SUMMARY: Parse the input data read from DUT due to IRQ. Handle data based
* on if its a response to a command or asynchronous touch data / reset
* sentinel. PIP2.x messages have additional error checking that is
* parsed (SEQ match from cmd to rsp, CRC valid).
* Look for special packets based on unique lengths:
* 0 bytes - APP(FW) reset sentinel or Gen5/6 BL sentinel
* 2 bytes - Empty buffer (PIP 1.7 and earlier)
* 11 bytes - possible PIP2.x reset sentinel (TAG and SEQ must = 0)
* 0xFFXX - Empty buffer (PIP 1.7+)
* Queue a startup after any asynchronous FW reset sentinel is seen, unless
* the initial probe has not yet been done.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_parse_input(struct pt_core_data *cd)
{
int report_id;
int cmd_id;
int is_command = 0;
int size;
int print_size;
bool touch_report = true;
unsigned short calc_crc;
unsigned short resp_crc;
cd->fw_sys_mode_in_standby_state = false;
size = get_unaligned_le16(&cd->input_buf[0]);
print_size = size;
pt_debug(cd->dev, DL_DEBUG, "<<< %s: IRQ Triggered, read len [%d]\n",
__func__, print_size);
if (print_size <= PT_MAX_INPUT)
pt_pr_buf(cd->dev, DL_DEBUG, cd->input_buf, print_size,
"<<< Read buf");
if (size == 0 ||
(size == 11 &&
(cd->input_buf[PIP2_RESP_SEQUENCE_OFFSET] &
PIP2_RESP_SEQUENCE_MASK) == 0 &&
(cd->input_buf[PIP2_RESP_REPORT_ID_OFFSET] &
PIP2_CMD_COMMAND_ID_MASK) ==
PIP2_CMD_ID_STATUS)) {
touch_report = false;
cd->hw_detected = true;
cd->bl_pip_ver_ready = false;
cd->app_pip_ver_ready = false;
if (size == 0) {
mutex_lock(&cd->system_lock);
cd->pip2_prot_active = false;
if (cd->active_dut_generation == DUT_PIP1_ONLY) {
/*
* For Gen5/6 this sentinel could be from
* the BL or FW. Attempt to set the correct
* mode based on the previous PIP command.
*/
if (cd->hid_cmd_state ==
PIP1_BL_CMD_ID_LAUNCH_APP + 1) {
cd->mode = PT_MODE_OPERATIONAL;
cd->startup_status =
STARTUP_STATUS_FW_RESET_SENTINEL;
} else if (cd->hid_cmd_state ==
PIP1_CMD_ID_START_BOOTLOADER + 1 ||
cd->hid_reset_cmd_state) {
cd->mode = PT_MODE_BOOTLOADER;
cd->startup_status =
STARTUP_STATUS_BL_RESET_SENTINEL;
} else {
cd->mode = PT_MODE_UNKNOWN;
cd->startup_status =
STARTUP_STATUS_START;
}
cd->fw_system_mode = FW_SYS_MODE_UNDEFINED;
pt_debug(cd->dev, DL_INFO,
"%s: ATM Gen5/6 %s sentinel received\n",
__func__,
(cd->mode == PT_MODE_OPERATIONAL ?
"FW" :
(cd->mode == PT_MODE_BOOTLOADER ?
"BL" : "Unknown")));
} else {
cd->mode = PT_MODE_OPERATIONAL;
cd->fw_system_mode = FW_SYS_MODE_BOOT;
cd->startup_status =
STARTUP_STATUS_FW_RESET_SENTINEL;
pt_debug(cd->dev, DL_INFO,
"%s: ATM PT/TT FW sentinel received\n",
__func__);
}
mutex_unlock(&cd->system_lock);
if (pt_allow_enumeration(cd)) {
if (cd->active_dut_generation == DUT_UNKNOWN) {
pt_debug(cd->dev, DL_INFO,
"%s: Queue Restart\n", __func__);
pt_queue_restart(cd);
} else {
pt_debug(cd->dev, DL_INFO,
"%s: Queue Enum\n", __func__);
pt_queue_enum(cd);
}
} else {
pt_debug(cd->dev, DL_INFO,
"%s: Sentinel - No Queued Action\n",
__func__);
}
} else {
/* Sentinel must be from TT/TC BL */
mutex_lock(&cd->system_lock);
cd->pip2_prot_active = true;
cd->startup_status = STARTUP_STATUS_BL_RESET_SENTINEL;
cd->mode = PT_MODE_BOOTLOADER;
cd->sysinfo.ready = false;
mutex_unlock(&cd->system_lock);
pt_debug(cd->dev, DL_INFO,
"%s: BL Reset sentinel received\n", __func__);
if (cd->flashless_dut &&
cd->flashless_auto_bl == PT_ALLOW_AUTO_BL) {
pt_debug(cd->dev, DL_INFO,
"%s: BL to RAM for flashless DUT\n",
__func__);
kthread_run(start_fw_upgrade, cd, "pt_loader");
}
}
mutex_lock(&cd->system_lock);
memcpy(cd->response_buf, cd->input_buf, 2);
if (!cd->hid_reset_cmd_state && !cd->hid_cmd_state) {
mutex_unlock(&cd->system_lock);
pt_debug(cd->dev, DL_WARN,
"%s: Device Initiated Reset\n", __func__);
wake_up(&cd->wait_q);
return 0;
}
cd->hid_reset_cmd_state = 0;
if (cd->hid_cmd_state == PIP1_CMD_ID_START_BOOTLOADER + 1 ||
cd->hid_cmd_state == PIP1_BL_CMD_ID_LAUNCH_APP + 1 ||
cd->hid_cmd_state == PIP1_CMD_ID_USER_CMD + 1)
cd->hid_cmd_state = 0;
wake_up(&cd->wait_q);
mutex_unlock(&cd->system_lock);
return 0;
} else if (size == 2 || size >= PT_PIP_1P7_EMPTY_BUF) {
/*
* This debug message below is used by PBATS to calculate the
* time from the last lift off IRQ to when FW exits LFT mode.
*/
touch_report = false;
pt_debug(cd->dev, DL_WARN,
"%s: DUT - Empty buffer detected\n", __func__);
return 0;
} else if (size > PT_MAX_INPUT || size < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: DUT - Unexpected len field in active bus data!\n",
__func__);
return -EINVAL;
}
if (cd->pip2_prot_active) {
pt_debug(cd->dev, DL_DEBUG,
"%s: Decode PIP2.x Response\n", __func__);
/* PIP2 does not have a report id, hard code it */
report_id = 0x00;
cmd_id = cd->input_buf[PIP2_RESP_COMMAND_ID_OFFSET];
calc_crc = crc_ccitt_calculate(cd->input_buf, size - 2);
resp_crc = cd->input_buf[size - 2] << 8;
resp_crc |= cd->input_buf[size - 1];
if ((cd->pip2_cmd_tag_seq !=
(cd->input_buf[PIP2_RESP_SEQUENCE_OFFSET] & 0x0F)) &&
(resp_crc != calc_crc) &&
((cd->input_buf[PIP1_RESP_REPORT_ID_OFFSET]
== PT_PIP_TOUCH_REPORT_ID) ||
(cd->input_buf[PIP1_RESP_REPORT_ID_OFFSET]
== PT_PIP_CAPSENSE_BTN_REPORT_ID))) {
pt_debug(cd->dev, DL_WARN,
"%s: %s %d %s\n",
__func__,
"Received PIP1 report id =",
cd->input_buf[PIP1_RESP_REPORT_ID_OFFSET],
"when expecting a PIP2 report - IGNORE report");
return 0;
}
is_command = 1;
touch_report = false;
} else {
report_id = cd->input_buf[PIP1_RESP_REPORT_ID_OFFSET];
cmd_id = cd->input_buf[PIP1_RESP_COMMAND_ID_OFFSET];
}
#ifdef TTDL_DIAGNOSTICS
pt_debug(cd->dev, DL_DEBUG,
"%s: pip2 = %d report_id: 0x%02X, cmd_code: 0x%02X\n",
__func__, cd->pip2_prot_active, report_id,
(cmd_id & PIP2_CMD_COMMAND_ID_MASK));
#endif /* TTDL_DIAGNOSTICS */
if (report_id == PT_PIP_WAKEUP_REPORT_ID) {
pt_wakeup_host(cd);
#ifdef TTHE_TUNER_SUPPORT
tthe_print(cd, cd->input_buf, size, "TT_WAKEUP=");
#endif
return 0;
}
mod_timer_pending(&cd->watchdog_timer, jiffies +
msecs_to_jiffies(cd->watchdog_interval));
/*
* If it is PIP2 response, the report_id has been set to 0,
* so it will not be parsed as a touch packet.
*/
if (!pt_is_touch_report(report_id)) {
is_command = 1;
touch_report = false;
}
if (unlikely(is_command)) {
parse_command_input(cd, size);
return 0;
}
if (touch_report)
parse_touch_input(cd, size);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_read_input
*
* SUMMARY: Reads incoming data off of the active bus
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_read_input(struct pt_core_data *cd)
{
struct device *dev = cd->dev;
int rc = 0;
int t;
int retry = PT_BUS_READ_INPUT_RETRY_COUNT;
/*
* Workaround for easywake failure
* Interrupt for easywake, wait for bus controller to wake
*/
mutex_lock(&cd->system_lock);
if (IS_EASY_WAKE_CONFIGURED(cd->easy_wakeup_gesture)) {
if (cd->sleep_state == SS_SLEEP_ON || cd->sleep_state == SS_EASY_WAKING_ON) {
mutex_unlock(&cd->system_lock);
if (!dev->power.is_suspended)
goto read;
t = wait_event_timeout(cd->wait_q,
(cd->wait_until_wake == 1),
msecs_to_jiffies(2000));
#ifdef TTDL_DIAGNOSTICS
if (IS_TMO(t)) {
cd->bus_transmit_error_count++;
pt_toggle_err_gpio(cd, PT_ERR_GPIO_I2C_TRANS);
pt_debug(dev, DL_ERROR,
"%s: !!!I2C Transmission Error %d\n",
__func__,
cd->bus_transmit_error_count);
}
#else
if (IS_TMO(t))
pt_queue_enum(cd);
#endif /* TTDL_DIAGNOSTICS */
goto read;
}
}
mutex_unlock(&cd->system_lock);
read:
/* Try reading up to 'retry' times */
while (retry-- != 0) {
rc = pt_adap_read_default_nosize(cd, cd->input_buf,
PT_MAX_INPUT);
if (!rc) {
pt_debug(dev, DL_DEBUG,
"%s: Read input successfully\n", __func__);
goto read_exit;
}
usleep_range(1000, 2000);
}
pt_debug(dev, DL_ERROR,
"%s: Error getting report, rc=%d\n", __func__, rc);
read_exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_irq
*
* SUMMARY: Process all detected interrupts
*
* RETURN:
* IRQ_HANDLED - Finished processing the interrupt
*
* PARAMETERS:
* irq - IRQ number
* *handle - pointer to core data struct
******************************************************************************/
irqreturn_t pt_irq(int irq, void *handle)
{
struct pt_core_data *cd = handle;
int rc = 0;
if (!pt_check_irq_asserted(cd))
return IRQ_HANDLED;
rc = pt_read_input(cd);
#ifdef TTDL_DIAGNOSTICS
cd->irq_count++;
/* Used to calculate T-Refresh */
if (cd->t_refresh_active) {
if (cd->t_refresh_count == 0) {
cd->t_refresh_time = jiffies;
cd->t_refresh_count++;
} else if (cd->t_refresh_count < cd->t_refresh_total) {
cd->t_refresh_count++;
} else {
cd->t_refresh_active = 0;
cd->t_refresh_time =
jiffies_to_msecs(jiffies - cd->t_refresh_time);
}
}
#endif /* TTDL_DIAGNOSTICS */
if (!rc)
pt_parse_input(cd);
return IRQ_HANDLED;
}
/*******************************************************************************
* FUNCTION: _pt_subscribe_attention
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to subscribe themselves into the TTDL attention list
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* type - attention type enum
* *id - ID of the module calling this function
* *func - callback function pointer to be called when notified
* mode - attention mode
******************************************************************************/
int _pt_subscribe_attention(struct device *dev,
enum pt_atten_type type, char *id, int (*func)(struct device *),
int mode)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct atten_node *atten, *atten_new;
atten_new = kzalloc(sizeof(*atten_new), GFP_KERNEL);
if (!atten_new)
return -ENOMEM;
pt_debug(cd->dev, DL_INFO, "%s from '%s'\n", __func__,
dev_name(cd->dev));
spin_lock(&cd->spinlock);
list_for_each_entry(atten, &cd->atten_list[type], node) {
if (atten->id == id && atten->mode == mode) {
spin_unlock(&cd->spinlock);
kfree(atten_new);
pt_debug(cd->dev, DL_INFO, "%s: %s=%p %s=%d\n",
__func__,
"already subscribed attention",
dev, "mode", mode);
return 0;
}
}
atten_new->id = id;
atten_new->dev = dev;
atten_new->mode = mode;
atten_new->func = func;
list_add(&atten_new->node, &cd->atten_list[type]);
spin_unlock(&cd->spinlock);
return 0;
}
/*******************************************************************************
* FUNCTION: _pt_unsubscribe_attention
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to unsubscribe themselves from the TTDL attention list
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* type - attention type enum
* *id - ID of the module calling this function
* *func - function pointer
* mode - attention mode
******************************************************************************/
int _pt_unsubscribe_attention(struct device *dev,
enum pt_atten_type type, char *id, int (*func)(struct device *),
int mode)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct atten_node *atten, *atten_n;
spin_lock(&cd->spinlock);
list_for_each_entry_safe(atten, atten_n, &cd->atten_list[type], node) {
if (atten->id == id && atten->mode == mode) {
list_del(&atten->node);
spin_unlock(&cd->spinlock);
pt_debug(cd->dev, DL_DEBUG, "%s: %s=%p %s=%d\n",
__func__,
"unsub for atten->dev", atten->dev,
"atten->mode", atten->mode);
kfree(atten);
return 0;
}
}
spin_unlock(&cd->spinlock);
return -ENODEV;
}
/*******************************************************************************
* FUNCTION: _pt_request_exclusive
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request exclusive access
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* timeout_ms - timeout to wait for exclusive access
******************************************************************************/
static int _pt_request_exclusive(struct device *dev,
int timeout_ms)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return request_exclusive(cd, (void *)dev, timeout_ms);
}
/*******************************************************************************
* FUNCTION: _pt_release_exclusive
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to release exclusive access
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static int _pt_release_exclusive(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return release_exclusive(cd, (void *)dev);
}
/*******************************************************************************
* FUNCTION: _pt_request_reset
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request the DUT to be reset. Function returns err if refused or
* timeout occurs (Note: core uses fixed timeout period).
*
* NOTE: Function blocks until ISR occurs.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* protect - flag to call protected or non-protected
******************************************************************************/
static int _pt_request_reset(struct device *dev, int protect)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int rc;
rc = pt_dut_reset(cd, protect);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR, "%s: Error on h/w reset r=%d\n",
__func__, rc);
}
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_enum
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request TTDL to queue an enum. This function will return err
* if refused; if no error then enum has completed and system is in
* normal operation mode.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* wait - boolean to determine if to wait for startup event
******************************************************************************/
static int _pt_request_enum(struct device *dev, bool wait)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
pt_queue_enum(cd);
if (wait)
wait_event_timeout(cd->wait_q,
cd->startup_state == STARTUP_NONE,
msecs_to_jiffies(PT_REQUEST_ENUM_TIMEOUT));
return 0;
}
/*******************************************************************************
* FUNCTION: _pt_request_sysinfo
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request the pointer to the system information structure. This
* function will return NULL if sysinfo has not been acquired from the
* DUT yet.
*
* RETURN: Pointer to the system information struct
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
struct pt_sysinfo *_pt_request_sysinfo(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int rc = 0;
/* Attempt to get sysinfo if not ready and panel_id is from XY pin */
if ((cd->panel_id_support & PT_PANEL_ID_BY_SYS_INFO) &&
!cd->sysinfo.ready) {
rc = pt_hid_output_get_sysinfo_(cd);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error getting sysinfo rc=%d\n",
__func__, rc);
}
}
if (cd->sysinfo.ready)
return &cd->sysinfo;
return NULL;
}
/*******************************************************************************
* FUNCTION: _pt_request_loader_pdata
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request the pointer to the loader platform data
*
* RETURN: Pointer to the loader platform data struct
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static struct pt_loader_platform_data *_pt_request_loader_pdata(
struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return cd->pdata->loader_pdata;
}
/*******************************************************************************
* FUNCTION: _pt_request_start_wd
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request to start the TTDL watchdog
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static int _pt_request_start_wd(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
pt_start_wd_timer(cd);
return 0;
}
/*******************************************************************************
* FUNCTION: _pt_request_stop_wd
*
* SUMMARY: Function pointer included in core_cmds to allow other modules
* to request to stop the TTDL watchdog
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static int _pt_request_stop_wd(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
pt_stop_wd_timer(cd);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_pip2_launch_app
*
* SUMMARY: Sends the PIP2 EXECUTE command to launch the APP and then wait for
* the FW reset sentinel to indicate the function succeeded.
*
* NOTE: Calling this function when the DUT is in Application mode WILL result
* in a timeout delay and with the DUT being reset with an XRES.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
* protect - flag to call protected or non-protected
******************************************************************************/
static int pt_pip2_launch_app(struct device *dev, int protect)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u16 actual_read_len;
u16 tmp_startup_status = cd->startup_status;
u8 read_buf[12];
u8 status;
int time = 0;
int rc = 0;
mutex_lock(&cd->system_lock);
cd->startup_status = STARTUP_STATUS_START;
pt_debug(dev, DL_DEBUG, "%s: Startup Status Reset\n", __func__);
mutex_unlock(&cd->system_lock);
rc = _pt_request_pip2_send_cmd(dev, protect,
PIP2_CMD_ID_EXECUTE, NULL, 0, read_buf,
&actual_read_len);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: PIP2 EXECUTE cmd failed rc = %d\n",
__func__, rc);
} else {
status = read_buf[PIP2_RESP_STATUS_OFFSET];
/* Test for no or invalid image in FLASH, no point to reset */
if (status == PIP2_RSP_ERR_INVALID_IMAGE) {
rc = status;
goto exit;
}
/* Any other boot failure */
if (status != 0) {
pt_debug(dev, DL_ERROR,
"%s: FW did not EXECUTE, status = %d\n",
__func__, status);
rc = status;
}
}
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: Failed to launch APP, XRES DUT rc = %d\n",
__func__, rc);
goto exit;
}
while ((cd->startup_status == STARTUP_STATUS_START) && time < 240) {
msleep(20);
pt_debug(cd->dev, DL_INFO, "%s: wait for %d for enum=0x%04X\n",
__func__, time, cd->startup_status);
time += 20;
}
if (cd->startup_status == STARTUP_STATUS_START) {
pt_debug(cd->dev, DL_WARN,
"%s: TMO waiting for FW reset sentinel\n", __func__);
rc = -ETIME;
}
exit:
if (cd->startup_status == STARTUP_STATUS_START) {
/* Reset to original state because we could be stuck in BL */
mutex_lock(&cd->system_lock);
cd->startup_status = tmp_startup_status;
mutex_unlock(&cd->system_lock);
}
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip2_launch_app
*
* SUMMARY: Calls pt_pip2_launch_app() when configured to. A small delay is
* inserted to ensure the reset has allowed the BL reset sentinel to be
* consumed.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
******************************************************************************/
static int _pt_request_pip2_launch_app(struct device *dev, int protect)
{
return pt_pip2_launch_app(dev, protect);
}
/*******************************************************************************
* FUNCTION: _pt_request_wait_for_enum_state
*
* SUMMARY: Loops for up to timeout waiting for the startup_status to reach
* the state passed in or STARTUP_STATUS_COMPLETE whichever comes first
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data structure
* timeout - timeout for how long to wait
* state - enum state to wait for
******************************************************************************/
static int _pt_request_wait_for_enum_state(struct device *dev, int timeout,
int state)
{
int rc = 0;
int t;
struct pt_core_data *cd = dev_get_drvdata(dev);
t = wait_event_timeout(cd->wait_q,
(cd->startup_status & state) || (cd->startup_status & 0x0100),
msecs_to_jiffies(timeout));
if (IS_TMO(t)) {
pt_debug(cd->dev, DL_ERROR,
"%s: TMO waiting for enum state 0x%04X in %dms\n",
__func__, state, timeout);
pt_debug(cd->dev, DL_WARN,
"%s: enum state reached 0x%04X\n",
__func__, cd->startup_status);
rc = -ETIME;
} else if (cd->startup_status & state) {
pt_debug(cd->dev, DL_INFO,
"%s: Enum state reached: enum=0x%04X in %dms\n",
__func__, cd->startup_status,
(t == 1) ? timeout : (timeout - jiffies_to_msecs(t)));
} else {
if (t == 1) {
pt_debug(
cd->dev, DL_ERROR,
"%s: TMO waiting for enum state 0x%04X in %dms\n",
__func__, state, timeout);
rc = -ETIME;
} else {
pt_debug(
cd->dev, DL_ERROR,
"%s: Enum state 0x%04X not reached in %dms\n",
__func__, state, timeout - jiffies_to_msecs(t));
rc = -EINVAL;
}
pt_debug(cd->dev, DL_INFO, "%s: enum state reached 0x%04X\n",
__func__, cd->startup_status);
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_wake_device_from_deep_sleep_
*
* SUMMARY: Call the set_power function and set the DUT to wake up from
* deep sleep.
*
* RETURN:
* 0 = success
* !0 = error
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_wake_device_from_deep_sleep_(
struct pt_core_data *cd)
{
int rc;
rc = pt_hid_cmd_set_power_(cd, HID_POWER_ON);
if (rc)
rc = -EAGAIN;
/* Prevent failure on sequential wake/sleep requests from OS */
msleep(20);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_wake_device_from_easy_wake_
*
* SUMMARY: Wake up device from Easy-Wake state.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_wake_device_from_easy_wake_(struct pt_core_data *cd)
{
int rc = 0;
rc = pt_core_wake_device_from_deep_sleep_(cd);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_restore_parameters_
*
* SUMMARY: This function sends all RAM parameters stored in the linked list
* back to the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
******************************************************************************/
static int pt_restore_parameters_(struct pt_core_data *cd)
{
struct param_node *param;
int rc = 0;
if (!(cd->cpdata->flags & PT_CORE_FLAG_RESTORE_PARAMETERS))
goto exit;
spin_lock(&cd->spinlock);
list_for_each_entry(param, &cd->param_list, node) {
spin_unlock(&cd->spinlock);
pt_debug(cd->dev, DL_INFO, "%s: Parameter id:%d value:%d\n",
__func__, param->id, param->value);
rc = pt_pip_set_param_(cd, param->id,
param->value, param->size);
if (rc)
goto exit;
spin_lock(&cd->spinlock);
}
spin_unlock(&cd->spinlock);
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_exit_bl_
*
* SUMMARY: Attempt to exit the BL and run the application, taking into account
* a DUT that may not have flash and will need FW to be loaded into RAM
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
* *status_str - pointer to optional status string buffer
* buf_size - size of status_str buffer
******************************************************************************/
int pt_pip2_exit_bl_(struct pt_core_data *cd, u8 *status_str, int buf_size)
{
int rc;
int wait_time = 0;
u8 mode = PT_MODE_UNKNOWN;
bool load_status_str = false;
/*
* Below function has protective call to ensure no enum is still on
* going, while this kind of protection should be applied widely in
* future (TODO).
*/
rc = pt_pip2_get_mode_sysmode(cd, &mode, NULL);
if (status_str && buf_size <= 50)
load_status_str = true;
if (mode == PT_MODE_BOOTLOADER) {
if (cd->flashless_dut == 1) {
rc = pt_hw_hard_reset(cd);
} else {
rc = pt_pip2_launch_app(cd->dev,
PT_CORE_CMD_UNPROTECTED);
if (rc == PIP2_RSP_ERR_INVALID_IMAGE) {
pt_debug(cd->dev, DL_ERROR, "%s: %s = %d\n",
__func__, "Invalid image in FLASH rc", rc);
} else if (rc) {
pt_debug(cd->dev, DL_ERROR, "%s: %s = %d\n",
__func__, "Failed to launch app rc", rc);
}
}
if (!rc) {
if (cd->flashless_dut == 1) {
/* Wait for BL to complete before enum */
rc = _pt_request_wait_for_enum_state(cd->dev,
4000, STARTUP_STATUS_FW_RESET_SENTINEL);
if (rc && load_status_str) {
strlcpy(status_str, "No FW sentinel after BL",
sizeof(*status_str)*PT_STATUS_STR_LEN);
goto exit;
}
}
/*
* If the host wants to interact with the FW or do a
* forced calibration, the FW must be out of BOOT mode
* and the system information must have been retrieved.
* Reaching the FW_OUT_OF_BOOT state guarantees both.
* If, however, the enumeration does not reach this
* point, the DUT may still be in APP mode so test
* for all conditions.
*/
rc = _pt_request_wait_for_enum_state(cd->dev, 4500,
STARTUP_STATUS_FW_OUT_OF_BOOT);
if (!rc || cd->startup_status >=
STARTUP_STATUS_FW_RESET_SENTINEL) {
mutex_lock(&cd->system_lock);
cd->mode = PT_MODE_OPERATIONAL;
mutex_unlock(&cd->system_lock);
}
if (rc) {
pt_debug(cd->dev, DL_WARN, "%s: %s: 0x%04X\n",
__func__, "Failed to enum with DUT",
cd->startup_status);
if (load_status_str && !(cd->startup_status &
STARTUP_STATUS_FW_OUT_OF_BOOT)) {
strlcpy(status_str, "FW Stuck in Boot mode",
sizeof(*status_str)*PT_STATUS_STR_LEN);
goto exit;
}
}
/*
* The coming FW sentinel could wake up the event
* queue, which has chance to be taken by next command
* wrongly. Following delay is a workaround to avoid
* this issue for most situations.
*/
msleep(20);
pt_start_wd_timer(cd);
}
if (load_status_str) {
if (rc == PIP2_RSP_ERR_INVALID_IMAGE)
strlcpy(status_str, "Failed - Invalid image in FLASH",
sizeof(*status_str)*PT_STATUS_STR_LEN);
else if (!rc)
strlcpy(status_str, "Entered APP from BL mode",
sizeof(*status_str)*PT_STATUS_STR_LEN);
else
strlcpy(status_str, "Failed to enter APP from BL mode",
sizeof(*status_str)*PT_STATUS_STR_LEN);
}
} else if (mode == PT_MODE_OPERATIONAL) {
mutex_lock(&cd->system_lock);
cd->mode = mode;
mutex_unlock(&cd->system_lock);
rc = pt_poll_for_fw_exit_boot_mode(cd, 1500, &wait_time);
if (load_status_str) {
if (!rc)
strlcpy(status_str, "Already in APP mode",
sizeof(*status_str)*PT_STATUS_STR_LEN);
else
strlcpy(status_str, "Already in APP mode - FW stuck in Boot mode",
sizeof(*status_str)*PT_STATUS_STR_LEN);
}
} else if (rc || mode == PT_MODE_UNKNOWN) {
mutex_lock(&cd->system_lock);
cd->mode = mode;
mutex_unlock(&cd->system_lock);
if (load_status_str)
strlcpy(status_str, "Failed to determine active mode",
sizeof(*status_str)*PT_STATUS_STR_LEN);
}
exit:
if (!rc)
pt_start_wd_timer(cd);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_exit_bl
*
* SUMMARY: Wrapper function for _pt_pip2_exit_bl that guarantees exclusive
* access.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
* *status_str - pointer to optional status string buffer
* buf_size - size of status_str buffer
******************************************************************************/
int pt_pip2_exit_bl(struct pt_core_data *cd, u8 *status_str, int buf_size)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n", __func__,
cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_pip2_exit_bl_(cd, status_str, buf_size);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR, "%s: fail to release exclusive\n",
__func__);
return rc;
}
/*******************************************************************************
* FUNCTION: _fast_startup
*
* SUMMARY: Perform fast startup after resume device by power on/off stratergy.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
******************************************************************************/
static int _fast_startup(struct pt_core_data *cd)
{
int retry = PT_CORE_STARTUP_RETRY_COUNT;
int rc = 0;
u8 mode = PT_MODE_UNKNOWN;
struct pt_hid_desc hid_desc;
int wait_time = 0;
memset(&hid_desc, 0, sizeof(hid_desc));
reset:
if (retry != PT_CORE_STARTUP_RETRY_COUNT)
pt_debug(cd->dev, DL_INFO, "%s: Retry %d\n", __func__,
PT_CORE_STARTUP_RETRY_COUNT - retry);
if (cd->active_dut_generation == DUT_PIP1_ONLY) {
pt_debug(cd->dev, DL_INFO, "%s: PIP1 Enumeration start\n",
__func__);
pt_flush_bus_if_irq_asserted(cd, PT_FLUSH_BUS_BASED_ON_LEN);
rc = pt_get_hid_descriptor_(cd, &hid_desc);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on getting HID descriptor r=%d\n",
__func__, rc);
if (retry--)
goto reset;
goto exit;
}
cd->mode = pt_get_mode(cd, &hid_desc);
if (cd->mode == PT_MODE_BOOTLOADER) {
pt_debug(cd->dev, DL_INFO, "%s: Bootloader mode\n",
__func__);
rc = pt_hid_output_bl_launch_app_(cd);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on launch app r=%d\n",
__func__, rc);
if (retry--)
goto reset;
goto exit;
}
rc = pt_get_hid_descriptor_(cd, &hid_desc);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on getting HID descriptor r=%d\n",
__func__, rc);
if (retry--)
goto reset;
goto exit;
}
cd->mode = pt_get_mode(cd, &hid_desc);
if (cd->mode == PT_MODE_BOOTLOADER) {
if (retry--)
goto reset;
goto exit;
}
}
cd->startup_status |= STARTUP_STATUS_GET_DESC;
cd->startup_status |= STARTUP_STATUS_FW_OUT_OF_BOOT;
} else {
pt_debug(cd->dev, DL_INFO, "%s: PIP2 Enumeration start\n",
__func__);
if (retry == PT_CORE_STARTUP_RETRY_COUNT) {
/* Wait for any sentinel before first try */
rc = _pt_request_wait_for_enum_state(
cd->dev, 150,
STARTUP_STATUS_BL_RESET_SENTINEL |
STARTUP_STATUS_FW_RESET_SENTINEL);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: No Sentinel detected rc = %d\n",
__func__, rc);
} else
pt_flush_bus_if_irq_asserted(cd,
PT_FLUSH_BUS_BASED_ON_LEN);
rc = pt_pip2_get_mode_sysmode_(cd, &mode, NULL);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Get mode failed, mode unknown\n",
__func__);
mode = PT_MODE_UNKNOWN;
}
cd->mode = mode;
if (cd->mode == PT_MODE_BOOTLOADER) {
pt_debug(cd->dev, DL_INFO, "%s: Bootloader mode\n",
__func__);
rc = pt_pip2_exit_bl_(cd, NULL, 0);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s Failed to exit bootloader\n",
__func__);
msleep(50);
rc = -ENODEV;
if (retry--)
goto reset;
goto exit;
} else {
pt_debug(cd->dev, DL_INFO,
"%s: Exit bootloader successfully\n",
__func__);
}
if (cd->mode != PT_MODE_OPERATIONAL) {
pt_debug(cd->dev, DL_WARN,
"%s: restore mode failure mode = %d\n",
__func__, cd->mode);
if (retry--)
goto reset;
goto exit;
}
}
cd->startup_status |= STARTUP_STATUS_GET_DESC;
}
/* FW cannot handle most PIP cmds when it is still in BOOT mode */
rc = _pt_poll_for_fw_exit_boot_mode(cd, 500, &wait_time);
if (!rc) {
cd->startup_status |= STARTUP_STATUS_FW_OUT_OF_BOOT;
pt_debug(cd->dev, DL_WARN,
"%s: Exit FW BOOT Mode after %dms\n",
__func__, wait_time);
} else {
pt_debug(cd->dev, DL_WARN,
"%s: FW stuck in BOOT Mode after %dms\n",
__func__, wait_time);
goto exit;
}
if (!cd->sysinfo.ready) {
rc = pt_hid_output_get_sysinfo_(cd);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on getting sysinfo r=%d\n",
__func__, rc);
if (retry--)
goto reset;
goto exit;
}
}
cd->startup_status |= STARTUP_STATUS_GET_SYS_INFO;
rc = pt_restore_parameters_(cd);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: failed to restore parameters rc=%d\n",
__func__, rc);
else
cd->startup_status |= STARTUP_STATUS_RESTORE_PARM;
exit:
cd->startup_status |= STARTUP_STATUS_COMPLETE;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_poweron_device_
*
* SUMMARY: Power on device, enable IRQ, and then perform a fast startup.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_poweron_device_(struct pt_core_data *cd)
{
struct device *dev = cd->dev;
int rc = 0;
/*
* After power on action, the chip can general FW sentinel. It can
* trigger an enumeration without hid_reset_cmd_state flag. Since the
* _fast_startup() can perform a quick enumeration too, here doesn't
* need another enumeration.
*/
mutex_lock(&cd->system_lock);
cd->startup_status = STARTUP_STATUS_START;
cd->hid_reset_cmd_state = 1;
mutex_unlock(&cd->system_lock);
rc = cd->cpdata->power(cd->cpdata, 1, dev, 0);
if (rc < 0) {
pt_debug(dev, DL_ERROR, "%s: HW Power up fails r=%d\n",
__func__, rc);
goto exit;
}
if (!cd->irq_enabled) {
cd->irq_enabled = true;
enable_irq(cd->irq);
}
/* TBD: following function doesn't update startup_status */
rc = _fast_startup(cd);
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_wake_device_from_deep_standby_
*
* SUMMARY: Reset device, and then trigger a full enumeration.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_wake_device_from_deep_standby_(struct pt_core_data *cd)
{
int rc;
rc = pt_dut_reset_and_wait(cd);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR, "%s: Error on h/w reset r=%d\n",
__func__, rc);
goto exit;
}
rc = _fast_startup(cd);
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_easywake_off_
*
* SUMMARY: Resume the device with a power on or wake from deep sleep based on
* the configuration in the core platform data structure.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_easywake_off_(struct pt_core_data *cd)
{
int rc = 0;
mutex_lock(&cd->system_lock);
if (cd->sleep_state == SS_EASY_WAKING_OFF) {
mutex_unlock(&cd->system_lock);
pt_debug(cd->dev, DL_INFO,
"%s - %d skip wakeoff\n", __func__, cd->sleep_state);
return 0;
}
mutex_unlock(&cd->system_lock);
if (!(cd->cpdata->flags & PT_CORE_FLAG_SKIP_RESUME)) {
if (IS_EASY_WAKE_CONFIGURED(cd->easy_wakeup_gesture))
rc = pt_core_wake_device_from_easy_wake_(cd);
if (rc < 0)
pt_debug(cd->dev, DL_ERROR,
"%s - %d failed %d\n", __func__, rc);
}
mutex_lock(&cd->system_lock);
cd->sleep_state = SS_EASY_WAKING_OFF;
mutex_unlock(&cd->system_lock);
pt_start_wd_timer(cd);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_easywake_off
*
* SUMMARY: Protected call to pt_core_easywake_off by exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_easywake_off(struct pt_core_data *cd)
{
int rc;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_core_easywake_off_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR, "%s: fail to release exclusive\n",
__func__);
else
pt_debug(cd->dev, DL_DEBUG, "%s: pass release exclusive\n",
__func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_wake_
*
* SUMMARY: Resume the device with a power on or wake from deep sleep based on
* the configuration in the core platform data structure.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_wake_(struct pt_core_data *cd)
{
int rc = 0;
mutex_lock(&cd->system_lock);
if (cd->sleep_state == SS_SLEEP_OFF || cd->sleep_state == SS_WAKING) {
mutex_unlock(&cd->system_lock);
pt_debug(cd->dev, DL_INFO,
"%s - skip wake sleep state %d\n", __func__, cd->sleep_state);
return 0;
} else {
cd->sleep_state = SS_WAKING;
}
mutex_unlock(&cd->system_lock);
if (!(cd->cpdata->flags & PT_CORE_FLAG_SKIP_RESUME)) {
if (cd->cpdata->flags & PT_CORE_FLAG_POWEROFF_ON_SLEEP) {
pt_debug(cd->dev, DL_INFO,
"%s: Entering into poweron mode:\n", __func__);
rc = pt_core_poweron_device_(cd);
if (rc < 0)
pr_err("%s: Poweron error detected: rc=%d\n",
__func__, rc);
}
else if (cd->cpdata->flags & PT_CORE_FLAG_DEEP_STANDBY)
rc = pt_core_wake_device_from_deep_standby_(cd);
else /* Default action to exit DeepSleep */
rc = pt_core_wake_device_from_deep_sleep_(cd);
}
mutex_lock(&cd->system_lock);
cd->sleep_state = SS_SLEEP_OFF;
mutex_unlock(&cd->system_lock);
pt_start_wd_timer(cd);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_wake_
*
* SUMMARY: Protected call to pt_core_wake_ by exclusive access to the DUT.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static int pt_core_wake(struct pt_core_data *cd)
{
int rc = 0;
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
return rc;
}
rc = pt_core_wake_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR, "%s: fail to release exclusive\n",
__func__);
else
pt_debug(cd->dev, DL_DEBUG, "%s: pass release exclusive\n",
__func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_get_ic_crc_
*
* SUMMARY: This function retrieves the config block CRC
*
* NOTE: The post condition of calling this function will be that the DUT will
* be in SCANNINING mode if no failures occur
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
* ebid - enumerated block ID
******************************************************************************/
static int pt_get_ic_crc_(struct pt_core_data *cd, u8 ebid)
{
struct pt_sysinfo *si = &cd->sysinfo;
int rc = 0;
u8 status;
u16 calculated_crc = 0;
u16 stored_crc = 0;
rc = pt_pip_suspend_scanning_(cd);
if (rc)
goto error;
rc = pt_pip_verify_config_block_crc_(cd, ebid, &status,
&calculated_crc, &stored_crc);
if (rc)
goto exit;
if (status) {
rc = -EINVAL;
goto exit;
}
si->ttconfig.crc = stored_crc;
exit:
pt_pip_resume_scanning_(cd);
error:
pt_debug(cd->dev, DL_INFO,
"%s: CRC: ebid:%d, calc:0x%04X, stored:0x%04X, rc=%d\n",
__func__, ebid, calculated_crc, stored_crc, rc);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_read_gpio
*
* SUMMARY: Sends a PIP2 READ_GPIO command to the DUT and stores the 32 gpio
* bits into the passed in variable
*
* NOTE: PIP2 READ_GPIO command is only supported in bootloader
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *status - pointer to where the command response status is stored
* *gpio - pointer to device attributes structure
******************************************************************************/
static int pt_pip2_read_gpio(struct device *dev, u8 *status, u32 *gpio)
{
int rc = 0;
u16 actual_read_len;
u8 read_buf[12];
u8 tmp_status = 0;
u8 index = PIP2_RESP_STATUS_OFFSET;
memset(read_buf, 0, ARRAY_SIZE(read_buf));
rc = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_READ_GPIO,
NULL, 0, read_buf, &actual_read_len);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: Failed to send PIP2 READ_GPIO cmd\n", __func__);
rc = -ECOMM;
} else {
tmp_status = read_buf[index];
}
if (status)
*status = tmp_status;
if (!rc && gpio && (tmp_status == 0)) {
*gpio = ((read_buf[index + 4] << 24) |
(read_buf[index + 3] << 16) |
(read_buf[index + 2] << 8) |
(read_buf[index + 1]));
}
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_get_panel_id_by_gpio
*
* SUMMARY: Wrapper function to call pt_pip2_read_gpio() to get panel ID
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
* *pid - pointer to store panel ID
******************************************************************************/
static int _pt_pip2_get_panel_id_by_gpio(struct pt_core_data *cd, u8 *pid)
{
u32 gpio_value = 0;
u8 status = 0;
u8 panel_id = PANEL_ID_NOT_ENABLED;
int rc = 0;
if (!pid)
return -ENOMEM;
rc = pt_pip2_read_gpio(cd->dev, &status, &gpio_value);
if (!rc) {
if (status == 0) {
panel_id = (gpio_value & PT_PANEL_ID_BITMASK) >>
PT_PANEL_ID_SHIFT;
pt_debug(cd->dev, DL_INFO, "%s: %s=0x%02X %s=0x%08X\n",
__func__,
"BL mode PID", panel_id, "gpio", gpio_value);
*pid = panel_id;
} else {
pt_debug(cd->dev, DL_ERROR, "%s: %s=%d\n",
__func__,
"BL read gpio failed status", status);
}
} else {
pt_debug(cd->dev, DL_ERROR, "%s: %s=%d\n",
__func__,
"BL read gpio failed status", status);
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_enum_with_dut_
*
* SUMMARY: This function does the full enumeration of the DUT with TTDL.
* The core data (cd) startup_status will store, as a bitmask, each
* state of the enumeration process. The startup will be attempted
* PT_CORE_STARTUP_RETRY_COUNT times before giving up.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
* reset - Flag to reset the DUT before attempting to enumerate
* *status - poionter to store the enum status bitmask flags
******************************************************************************/
static int pt_enum_with_dut_(struct pt_core_data *cd, bool reset,
u32 *enum_status)
{
int try = 1;
int rc = 0;
int wait_time = 0;
bool detected = false;
u8 return_data[8];
u8 mode = PT_MODE_UNKNOWN;
u8 pid = PANEL_ID_NOT_ENABLED;
u8 sys_mode = FW_SYS_MODE_UNDEFINED;
struct pt_hid_desc hid_desc;
memset(&hid_desc, 0, sizeof(hid_desc));
#ifdef TTHE_TUNER_SUPPORT
tthe_print(cd, NULL, 0, "enter startup");
#endif
pt_debug(cd->dev, DL_INFO, "%s: Start enum... 0x%04X, reset=%d\n",
__func__, cd->startup_status, reset);
pt_stop_wd_timer(cd);
reset:
if (try > 1)
pt_debug(cd->dev, DL_WARN, "%s: DUT Enum Attempt %d\n",
__func__, try);
pt_flush_bus_if_irq_asserted(cd, PT_FLUSH_BUS_BASED_ON_LEN);
if (cd->active_dut_generation == DUT_PIP1_ONLY) {
pt_debug(cd->dev, DL_INFO,
"%s: PIP1 Enumeration start\n", __func__);
/* Only reset the DUT after the first try */
if (reset || (try > 1)) {
/*
* Reset hardware only for Legacy parts. Skip for TT/TC
* parts because if the FW image was loaded directly
* to SRAM issueing a reset ill wipe out what was just
* loaded.
*/
rc = pt_dut_reset_and_wait(cd);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on h/w reset r=%d\n",
__func__, rc);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
/* sleep to allow FW to be launched if available */
msleep(120);
}
rc = pt_get_hid_descriptor_(cd, &hid_desc);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error getting HID Descriptor r=%d\n",
__func__, rc);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
rc = -EIO;
goto exit;
}
detected = true;
cd->mode = pt_get_mode(cd, &hid_desc);
/*
* Most systems do not use an XY pin as the panel_id and so
* the BL is used to retrieve the panel_id, however for
* systems that do use an XY pin, the panel_id MUST be
* retrieved from the system information when running FW
* (done below) and so this section of code is skipped.
* Entering the BL here is only needed on XY_PIN systems.
*/
if (cd->panel_id_support & PT_PANEL_ID_BY_BL) {
if (cd->mode == PT_MODE_OPERATIONAL) {
rc = pt_pip_start_bootloader_(cd);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on start bootloader r=%d\n",
__func__, rc);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
cd->mode = PT_MODE_BOOTLOADER;
pt_debug(cd->dev, DL_INFO, "%s: Bootloader mode\n",
__func__);
}
rc = pt_hid_output_bl_get_information_(cd, return_data);
if (!rc) {
cd->bl_info.ready = true;
cd->bl_info.chip_id =
get_unaligned_le16(&return_data[2]);
pt_debug(cd->dev, DL_INFO, "%s: chip ID %04X\n",
__func__, cd->bl_info.chip_id);
} else {
pt_debug(cd->dev, DL_ERROR,
"%s: failed to get chip ID, r=%d\n",
__func__, rc);
}
rc = pt_hid_output_bl_get_panel_id_(cd, &pid);
mutex_lock(&cd->system_lock);
if (!rc) {
cd->pid_for_loader = pid;
pt_debug(cd->dev, DL_INFO, "%s: Panel ID: 0x%02X\n",
__func__, cd->pid_for_loader);
} else {
cd->pid_for_loader = PANEL_ID_NOT_ENABLED;
pt_debug(cd->dev, DL_WARN,
"%s: Read Failed, disable Panel ID: 0x%02X\n",
__func__, cd->pid_for_loader);
}
mutex_unlock(&cd->system_lock);
}
/* Exit BL due to XY_PIN case or any other cause to be in BL */
if (cd->mode == PT_MODE_BOOTLOADER) {
rc = pt_hid_output_bl_launch_app_(cd);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on launch app r=%d\n",
__func__, rc);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
rc = -ENODEV;
goto exit;
}
/* sleep to allow FW to be launched if available */
msleep(120);
/* Ensure the DUT is now in Application mode */
rc = pt_get_hid_descriptor_(cd, &hid_desc);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error getting HID Desc r=%d\n",
__func__, rc);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
rc = -EIO;
goto exit;
}
cd->mode = pt_get_mode(cd, &hid_desc);
if (cd->mode == PT_MODE_BOOTLOADER) {
pt_debug(cd->dev, DL_WARN,
"%s: Error confiming exit BL\n",
__func__);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
rc = -ENODEV;
goto exit;
}
}
pt_debug(cd->dev, DL_INFO, "%s: Operational mode\n", __func__);
cd->mode = PT_MODE_OPERATIONAL;
*enum_status |= STARTUP_STATUS_GET_DESC;
*enum_status |= STARTUP_STATUS_FW_OUT_OF_BOOT;
} else {
/* Generation is PIP2 Capable */
pt_debug(cd->dev, DL_INFO,
"%s: PIP2 Enumeration start\n", __func__);
rc = pt_pip2_get_mode_sysmode_(cd, &mode, NULL);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Get mode failed, mode unknown\n",
__func__);
mode = PT_MODE_UNKNOWN;
} else
detected = true;
cd->mode = mode;
switch (cd->mode) {
case PT_MODE_OPERATIONAL:
pt_debug(cd->dev, DL_INFO,
"%s: Operational mode\n", __func__);
if (cd->app_pip_ver_ready == false) {
rc = pt_pip2_get_version_(cd);
if (!rc)
cd->app_pip_ver_ready = true;
else {
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
}
break;
case PT_MODE_BOOTLOADER:
pt_debug(cd->dev, DL_INFO,
"%s: Bootloader mode\n", __func__);
if (cd->panel_id_support & PT_PANEL_ID_BY_BL) {
rc = _pt_pip2_get_panel_id_by_gpio(cd, &pid);
mutex_lock(&cd->system_lock);
if (!rc) {
cd->pid_for_loader = pid;
pt_debug(cd->dev, DL_INFO,
"%s: Panel ID: 0x%02X\n",
__func__, cd->pid_for_loader);
} else {
cd->pid_for_loader =
PANEL_ID_NOT_ENABLED;
pt_debug(cd->dev, DL_WARN,
"%s: Read Failed, disable Panel ID: 0x%02X\n",
__func__, cd->pid_for_loader);
}
mutex_unlock(&cd->system_lock);
}
if (cd->bl_pip_ver_ready == false) {
rc = pt_pip2_get_version_(cd);
if (!rc)
cd->bl_pip_ver_ready = true;
else {
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
}
/*
* Launch app command will fail in flashless mode.
* Skip launch app command here to save time for
* enumeration flow.
*/
if (cd->flashless_dut)
goto exit;
/*
* pt_pip2_launch_app() is needed here instead of
* pt_pip2_exit_bl() because exit_bl will cause several
* hw_resets to occur and the auto BL on a flashless
* DUT will fail.
*/
rc = pt_pip2_launch_app(cd->dev,
PT_CORE_CMD_UNPROTECTED);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on launch app r=%d\n",
__func__, rc);
msleep(50);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
/*
* IRQ thread can be delayed if the serial log print is
* enabled. It causes next command to get wrong response
* Here the delay is to ensure pt_parse_input() to be
* finished.
*/
msleep(60);
/* Check and update the mode */
rc = pt_pip2_get_mode_sysmode_(cd, &mode, NULL);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Get mode failed, mode unknown\n",
__func__);
mode = PT_MODE_UNKNOWN;
}
cd->mode = mode;
if (cd->mode == PT_MODE_OPERATIONAL) {
pt_debug(cd->dev, DL_INFO,
"%s: Launched to Operational mode\n",
__func__);
} else if (cd->mode == PT_MODE_BOOTLOADER) {
pt_debug(cd->dev, DL_ERROR,
"%s: Launch failed, Bootloader mode\n",
__func__);
goto exit;
} else if (cd->mode == PT_MODE_UNKNOWN) {
pt_debug(cd->dev, DL_ERROR,
"%s: Launch failed, Unknown mode\n",
__func__);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
if (cd->app_pip_ver_ready == false) {
rc = pt_pip2_get_version_(cd);
if (!rc)
cd->app_pip_ver_ready = true;
else {
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
}
break;
default:
pt_debug(cd->dev, DL_ERROR,
"%s: Unknown mode\n", __func__);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
*enum_status |= STARTUP_STATUS_GET_DESC;
}
pt_init_pip_report_fields(cd);
*enum_status |= STARTUP_STATUS_GET_RPT_DESC;
if (!cd->features.easywake)
cd->easy_wakeup_gesture = PT_CORE_EWG_NONE;
pt_debug(cd->dev, DL_INFO, "%s: Reading sysinfo\n", __func__);
rc = pt_hid_output_get_sysinfo_(cd);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on getting sysinfo r=%d\n", __func__, rc);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
goto exit;
}
*enum_status |= STARTUP_STATUS_GET_SYS_INFO;
/* FW cannot handle most PIP cmds when it is still in BOOT mode */
rc = _pt_poll_for_fw_exit_boot_mode(cd, 10000, &wait_time);
if (!rc) {
*enum_status |= STARTUP_STATUS_FW_OUT_OF_BOOT;
pt_debug(cd->dev, DL_WARN,
"%s: Exit FW BOOT Mode after %dms\n",
__func__, wait_time);
} else {
pt_debug(cd->dev, DL_WARN,
"%s: FW stuck in BOOT Mode after %dms\n",
__func__, wait_time);
goto exit;
}
pt_debug(cd->dev, DL_INFO, "%s pt Prot Version: %d.%d\n",
__func__,
cd->sysinfo.ttdata.pip_ver_major,
cd->sysinfo.ttdata.pip_ver_minor);
rc = pt_get_ic_crc_(cd, PT_TCH_PARM_EBID);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: DUT Config block CRC failure rc=%d\n",
__func__, rc);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
} else {
_pt_get_fw_sys_mode(cd, &sys_mode, NULL);
if (sys_mode != FW_SYS_MODE_SCANNING) {
pt_debug(cd->dev, DL_ERROR,
"%s: scan state: %d, retry: %d\n",
__func__, sys_mode, try);
if (try++ < PT_CORE_STARTUP_RETRY_COUNT)
goto reset;
} else
*enum_status |= STARTUP_STATUS_GET_CFG_CRC;
}
rc = pt_restore_parameters_(cd);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: Failed to restore parameters rc=%d\n",
__func__, rc);
} else
*enum_status |= STARTUP_STATUS_RESTORE_PARM;
call_atten_cb(cd, PT_ATTEN_STARTUP, 0);
cd->watchdog_interval = PT_WATCHDOG_TIMEOUT;
cd->startup_retry_count = 0;
exit:
/* Generate the HW Version of the connected DUT and store in cd */
pt_generate_hw_version(cd, cd->hw_version);
pt_debug(cd->dev, DL_WARN, "%s: HW Version: %s\n", __func__,
cd->hw_version);
pt_start_wd_timer(cd);
if (!detected)
rc = -ENODEV;
#ifdef TTHE_TUNER_SUPPORT
tthe_print(cd, NULL, 0, "exit startup");
#endif
pt_debug(cd->dev, DL_WARN,
"%s: Completed Enumeration rc=%d On Attempt %d\n",
__func__, rc, try);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_enum_with_dut
*
* SUMMARY: This is the safe function wrapper for pt_enum_with_dut_() by
* requesting exclusive access around the call.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer the core data structure
* reset - Flag to reset the DUT before attempting to enumerate
* *status - pointer to store the enum status bitmask flags
******************************************************************************/
static int pt_enum_with_dut(struct pt_core_data *cd, bool reset, u32 *status)
{
int rc = 0;
mutex_lock(&cd->system_lock);
cd->startup_state = STARTUP_RUNNING;
mutex_unlock(&cd->system_lock);
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
goto exit;
}
rc = pt_enum_with_dut_(cd, reset, status);
if (release_exclusive(cd, cd->dev) < 0)
/* Don't return fail code, mode is already changed. */
pt_debug(cd->dev, DL_ERROR, "%s: fail to release exclusive\n",
__func__);
else
pt_debug(cd->dev, DL_DEBUG, "%s: pass release exclusive\n",
__func__);
exit:
mutex_lock(&cd->system_lock);
/* Clear startup state for any tasks waiting for startup completion */
cd->startup_state = STARTUP_NONE;
mutex_unlock(&cd->system_lock);
/* Set STATUS_COMPLETE bit to indicate the status is ready to be read */
*status |= STARTUP_STATUS_COMPLETE;
/* Wake the waiters for end of startup */
wake_up(&cd->wait_q);
return rc;
}
static int add_sysfs_interfaces(struct device *dev);
static void remove_sysfs_interfaces(struct device *dev);
static void remove_sysfs_and_modules(struct device *dev);
static void pt_release_modules(struct pt_core_data *cd);
static void pt_probe_modules(struct pt_core_data *cd);
/*******************************************************************************
* FUNCTION: _pt_ttdl_restart
*
* SUMMARY: Restarts TTDL enumeration with the DUT and re-probes all modules
*
* NOTE: The function DOSE NOT remove sysfs and modules. Trying to create
* existing sysfs nodes will produce an error.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static int _pt_ttdl_restart(struct device *dev)
{
int rc = 0;
struct pt_core_data *cd = dev_get_drvdata(dev);
#ifdef CONFIG_TOUCHSCREEN_PARADE_I2C
struct i2c_client *client =
(struct i2c_client *)container_of(dev, struct i2c_client, dev);
#endif
/*
* Make sure the device is awake, pt_mt_release function will
* cause pm sleep function and lead to deadlock.
*/
pm_runtime_get_sync(dev);
/* Use ttdl_restart_lock to avoid reentry */
mutex_lock(&cd->ttdl_restart_lock);
remove_sysfs_and_modules(cd->dev);
#ifdef CONFIG_TOUCHSCREEN_PARADE_I2C
if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
pt_debug(dev, DL_ERROR,
"%s I2C functionality not Supported\n", __func__);
rc = -EIO;
goto ttdl_no_error;
}
#endif
if (cd->active_dut_generation == DUT_UNKNOWN) {
rc = _pt_detect_dut_generation(cd->dev,
&cd->startup_status, &cd->active_dut_generation,
&cd->mode);
if ((cd->active_dut_generation == DUT_UNKNOWN) || (rc)) {
pt_debug(dev, DL_ERROR,
"%s: Error, Unknown DUT Generation rc=%d\n",
__func__, rc);
}
}
rc = add_sysfs_interfaces(cd->dev);
if (rc < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: Error, failed sysfs nodes rc=%d\n",
__func__, rc);
if (!(cd->startup_status & STARTUP_STATUS_BL_RESET_SENTINEL)) {
pt_debug(dev, DL_INFO, "%s: Call pt_enum_with_dut\n", __func__);
rc = pt_enum_with_dut(cd, true, &cd->startup_status);
if (rc < 0)
pt_debug(dev, DL_ERROR,
"%s: Error, Failed to Enumerate\n", __func__);
}
rc = pt_mt_probe(dev);
if (rc < 0) {
pt_debug(dev, DL_ERROR,
"%s: Error, fail mt probe\n", __func__);
}
rc = pt_btn_probe(dev);
if (rc < 0) {
pt_debug(dev, DL_ERROR,
"%s: Error, fail btn probe\n", __func__);
}
pt_probe_modules(cd);
pt_debug(cd->dev, DL_WARN,
"%s: Well Done! TTDL Restart Completed\n", __func__);
rc = 0;
#ifdef CONFIG_TOUCHSCREEN_PARADE_I2C
ttdl_no_error:
#endif
mutex_unlock(&cd->ttdl_restart_lock);
mutex_lock(&cd->system_lock);
cd->startup_status |= STARTUP_STATUS_COMPLETE;
cd->startup_state = STARTUP_NONE;
mutex_unlock(&cd->system_lock);
pm_runtime_put(dev);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_restart_work_function
*
* SUMMARY: This is the wrapper function placed in a work queue to call
* _pt_ttdl_restart()
*
* RETURN: none
*
* PARAMETERS:
* *work - pointer to the work_struct
******************************************************************************/
static void pt_restart_work_function(struct work_struct *work)
{
struct pt_core_data *cd = container_of(work,
struct pt_core_data, ttdl_restart_work);
int rc = 0;
rc = _pt_ttdl_restart(cd->dev);
if (rc < 0)
pt_debug(cd->dev, DL_ERROR, "%s: Fail queued startup r=%d\n",
__func__, rc);
}
/*******************************************************************************
* FUNCTION: pt_enum_work_function
*
* SUMMARY: This is the wrapper function placed in a work queue to call
* pt_enum_with_dut()
*
* RETURN: none
*
* PARAMETERS:
* *work - pointer to the work_struct
******************************************************************************/
static void pt_enum_work_function(struct work_struct *work)
{
struct pt_core_data *cd = container_of(work,
struct pt_core_data, enum_work);
int rc;
rc = pt_enum_with_dut(cd, false, &cd->startup_status);
if (rc < 0)
pt_debug(cd->dev, DL_ERROR, "%s: Fail queued startup r=%d\n",
__func__, rc);
}
static int pt_get_regulator(struct pt_core_data *cd, bool get)
{
int rc;
if (!get) {
rc = 0;
goto regulator_put;
}
cd->vdd = regulator_get(cd->dev, "vdd");
if (IS_ERR(cd->vdd)) {
rc = PTR_ERR(cd->vdd);
dev_err(cd->dev,
"Regulator get failed vdd rc=%d\n", rc);
goto regulator_put;
}
cd->vcc_i2c = regulator_get(cd->dev, "vcc_i2c");
if (IS_ERR(cd->vcc_i2c)) {
rc = PTR_ERR(cd->vcc_i2c);
dev_err(cd->dev,
"Regulator get failed vcc_i2c rc=%d\n", rc);
goto regulator_put;
}
return 0;
regulator_put:
if (cd->vdd) {
regulator_put(cd->vdd);
cd->vdd = NULL;
}
if (cd->vcc_i2c) {
regulator_put(cd->vcc_i2c);
cd->vcc_i2c = NULL;
}
return rc;
}
#ifdef ENABLE_I2C_REG_ONLY
static int pt_enable_i2c_regulator(struct pt_core_data *cd, bool en)
{
int rc = 0;
pt_debug(cd->dev, DL_INFO, "%s: Enter flag = %d\n", __func__, en);
if (!en) {
rc = 0;
goto disable_vcc_i2c_reg_only;
}
if (cd->vcc_i2c) {
rc = regulator_set_load(cd->vcc_i2c, I2C_ACTIVE_LOAD_MA);
if (rc < 0)
pt_debug(cd->dev, DL_INFO,
"%s: I2c unable to set active current rc = %d\n", __func__, rc);
pt_debug(cd->dev, DL_INFO, "%s: i2c set I2C_ACTIVE_LOAD_MA rc = %d\n",
__func__, rc);
}
return 0;
disable_vcc_i2c_reg_only:
if (cd->vcc_i2c) {
rc = regulator_set_load(cd->vcc_i2c, I2C_SUSPEND_LOAD_UA);
if (rc < 0)
pt_debug(cd->dev, DL_INFO, "%s: i2c unable to set 0 uAm rc = %d\n",
__func__, rc);
}
pt_debug(cd->dev, DL_INFO, "%s: Exit rc = %d I2C_SUSPEND_LOAD_UA\n", __func__, rc);
return rc;
}
#endif
static int pt_enable_regulator(struct pt_core_data *cd, bool en)
{
int rc;
if (!en) {
rc = 0;
goto disable_vcc_i2c_reg;
}
if (cd->vdd) {
if (regulator_count_voltages(cd->vdd) > 0) {
rc = regulator_set_voltage(cd->vdd, FT_VTG_MIN_UV,
FT_VTG_MAX_UV);
if (rc) {
dev_err(cd->dev,
"Regulator set_vtg failed vdd rc=%d\n", rc);
goto exit;
}
}
rc = regulator_enable(cd->vdd);
if (rc) {
dev_err(cd->dev,
"Regulator vdd enable failed rc=%d\n", rc);
goto exit;
}
dev_info(cd->dev, "%s: VDD regulator enabled:\n", __func__);
}
if (cd->vcc_i2c) {
if (regulator_count_voltages(cd->vcc_i2c) > 0) {
rc = regulator_set_voltage(cd->vcc_i2c, FT_I2C_VTG_MIN_UV,
FT_I2C_VTG_MAX_UV);
if (rc) {
dev_err(cd->dev,
"Regulator set_vtg failed vcc_i2c rc=%d\n", rc);
goto disable_vdd_reg;
}
}
rc = regulator_enable(cd->vcc_i2c);
if (rc) {
dev_err(cd->dev,
"Regulator vcc_i2c enable failed rc=%d\n", rc);
goto disable_vdd_reg;
}
dev_info(cd->dev, "%s: VCC I2C regulator enabled:\n", __func__);
}
return 0;
disable_vcc_i2c_reg:
if (cd->vcc_i2c) {
if (regulator_count_voltages(cd->vcc_i2c) > 0)
regulator_set_voltage(cd->vcc_i2c, FT_I2C_VTG_MIN_UV,
FT_I2C_VTG_MAX_UV);
regulator_disable(cd->vcc_i2c);
dev_info(cd->dev, "%s: VCC I2C regulator disabled:\n", __func__);
}
disable_vdd_reg:
if (cd->vdd) {
if (regulator_count_voltages(cd->vdd) > 0)
regulator_set_voltage(cd->vdd, FT_VTG_MIN_UV,
FT_VTG_MAX_UV);
regulator_disable(cd->vdd);
dev_info(cd->dev, "%s: VDD regulator disabled:\n", __func__);
}
exit:
return rc;
}
#if (KERNEL_VERSION(3, 19, 0) <= LINUX_VERSION_CODE)
#define KERNEL_VER_GT_3_19
#endif
#if defined(CONFIG_PM_RUNTIME) || defined(KERNEL_VER_GT_3_19)
/* CONFIG_PM_RUNTIME option is removed in 3.19.0 */
#if defined(CONFIG_PM_SLEEP)
/*******************************************************************************
* FUNCTION: pt_core_rt_suspend
*
* SUMMARY: Wrapper function with PM Runtime stratergy to call pt_core_sleep.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static int pt_core_rt_suspend(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
pt_debug(dev, DL_DEBUG, "%s Skip - probe state %d\n",
__func__, cd->core_probe_complete);
return 0;
}
/*******************************************************************************
* FUNCTION: pt_core_rt_resume
*
* SUMMARY: Wrapper function with PM Runtime stratergy to call pt_core_wake.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static int pt_core_rt_resume(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
pt_debug(dev, DL_DEBUG, "%s Skip - probe state %d\n",
__func__, cd->core_probe_complete);
return 0;
}
#endif /* CONFIG_PM_SLEEP */
#endif /* CONFIG_PM_RUNTIME || LINUX_VERSION_CODE */
#if defined(CONFIG_PM_SLEEP)
/*******************************************************************************
* FUNCTION: pt_core_suspend_
*
* SUMMARY: Wrapper function with device suspend/resume stratergy to call
* pt_core_sleep. This function may disable IRQ during sleep state.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static int pt_core_suspend_(struct device *dev)
{
int rc;
struct pt_core_data *cd = dev_get_drvdata(dev);
pt_debug(dev, DL_INFO, "%s: Enter\n", __func__);
rc = pt_core_sleep(cd);
if (rc) {
pt_debug(dev, DL_ERROR, "%s: Error on sleep rc =%d\n",
__func__, rc);
return -EAGAIN;
}
rc = pt_enable_regulator(cd, false);
if (!IS_EASY_WAKE_CONFIGURED(cd->easy_wakeup_gesture))
return 0;
/* Required to prevent interrupts before bus awake */
disable_irq(cd->irq);
cd->irq_disabled = 1;
if (device_may_wakeup(dev)) {
pt_debug(dev, DL_WARN, "%s Device MAY wakeup\n",
__func__);
if (!enable_irq_wake(cd->irq))
cd->irq_wake = 1;
} else {
pt_debug(dev, DL_WARN, "%s Device MAY NOT wakeup\n",
__func__);
}
pt_debug(dev, DL_INFO, "%s: Exit :\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_suspend
*
* SUMMARY: Wrapper function of pt_core_suspend_() to help avoid TP from being
* woke up or put to sleep based on Kernel power state even when the display
* is off based on the check of TTDL core platform flag.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static int pt_core_suspend(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int rc = 0;
if (cd->drv_debug_suspend || (cd->cpdata->flags & PT_CORE_FLAG_SKIP_SYS_SLEEP))
return 0;
if (pt_core_state == STATE_SUSPEND)
{
pt_debug(cd->dev, DL_INFO, "%s Already in Suspend state\n", __func__);
return 0;
}
pt_debug(cd->dev, DL_INFO, "%s Suspend start\n", __func__);
cancel_work_sync(&cd->resume_work);
cancel_work_sync(&cd->suspend_work);
mutex_lock(&cd->system_lock);
cd->wait_until_wake = 0;
mutex_unlock(&cd->system_lock);
if (pm_suspend_via_firmware() || cd->touch_offload) {
rc = pt_core_suspend_(cd->dev);
cd->quick_boot = true;
} else {
rc = pt_enable_i2c_regulator(cd, false);
if (rc < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: Error on disabling i2c regulator\n", __func__);
}
pt_debug(cd->dev, DL_INFO, "%s Suspend exit - rc = %d\n", __func__, rc);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_resume_
*
* SUMMARY: Wrapper function with device suspend/resume stratergy to call
* pt_core_wake. This function may enable IRQ before wake up.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static int pt_core_resume_(struct device *dev)
{
int rc = 0;
struct pt_core_data *cd = dev_get_drvdata(dev);
dev_info(dev, "%s: Entering into resume mode:\n",
__func__);
rc = pt_enable_regulator(cd, true);
dev_info(dev, "%s: Voltage regulator enabled: rc=%d\n",
__func__, rc);
if (!IS_EASY_WAKE_CONFIGURED(cd->easy_wakeup_gesture))
goto exit;
/*
* Bus pm does not call suspend if device runtime suspended
* This flag is covers that case
*/
if (cd->irq_disabled) {
enable_irq(cd->irq);
cd->irq_disabled = 0;
}
if (device_may_wakeup(dev)) {
pt_debug(dev, DL_WARN, "%s Device MAY wakeup\n",
__func__);
if (cd->irq_wake) {
disable_irq_wake(cd->irq);
cd->irq_wake = 0;
}
} else {
pt_debug(dev, DL_WARN, "%s Device MAY NOT wakeup\n",
__func__);
}
exit:
rc = pt_core_wake(cd);
if (rc) {
dev_err(dev, "%s: Failed to wake up: rc=%d\n",
__func__, rc);
return -EAGAIN;
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_core_restore
*
* SUMMARY: Wrapper function with device suspend/resume stratergy to call
* pt_core_wake. This function may enable IRQ before wake up.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static int pt_core_restore(struct device *dev)
{
int rc = 0;
struct pt_core_data *cd = dev_get_drvdata(dev);
dev_info(dev, "%s: Entering into resume mode:\n",
__func__);
queue_work(cd->pt_workqueue, &cd->resume_offload_work);
return rc;
}
/*******************************************************************************
* FUNCTION: suspend_offload_work
*
* SUMMARY: Wrapper function of pt_core_suspend() to avoid TP to be waken/slept
* along with kernel power state even the display is off based on the check of
* TTDL core platform flag.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static void pt_suspend_offload_work(struct work_struct *work)
{
int rc = 0;
struct pt_core_data *cd = container_of(work, struct pt_core_data,
suspend_offload_work);
pt_debug(cd->dev, DL_INFO, "%s start\n", __func__);
if (cd->cpdata->flags & PT_CORE_FLAG_SKIP_SYS_SLEEP)
return;
rc = pt_core_suspend_(cd->dev);
pt_debug(cd->dev, DL_WARN, "%s Exit - rc = %d\n", __func__, rc);
}
/*******************************************************************************
* FUNCTION: resume_offload_work
*
* SUMMARY: Wrapper function of pt_core_resume_() to avoid TP to be waken/slept
* along with kernel power state even the display is off based on the check of
* TTDL core platform flag.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static void pt_resume_offload_work(struct work_struct *work)
{
int rc = 0;
int retry_count = 1000;
struct pt_core_data *pt_data = container_of(work, struct pt_core_data,
resume_offload_work);
pt_debug(pt_data->dev, DL_INFO, "%s start\n", __func__);
do {
retry_count--;
rc = pt_core_resume_(pt_data->dev);
if (rc < 0)
pt_debug(pt_data->dev, DL_ERROR,
"%s: Error on wake\n", __func__);
} while (retry_count && rc < 0);
if (rc < 0){
pt_debug(pt_data->dev, DL_ERROR, "%s: Error on wake\n", __func__);
return;
}
#ifdef TOUCH_TO_WAKE_POWER_FEATURE_WORK_AROUND
rc = pt_core_easywake_on(pt_data);
if (rc < 0) {
pt_debug(pt_data->dev, DL_ERROR,
"%s: Error on enable touch to wake key\n",
__func__);
return;
}
pt_data->fb_state = FB_OFF;
pt_debug(pt_data->dev, DL_INFO, "%s End\n", __func__);
#endif
pt_data->quick_boot = false;
pt_debug(pt_data->dev, DL_INFO, "%s Exit\n", __func__);
}
/*******************************************************************************
* FUNCTION: pt_core_resume
*
* SUMMARY: Wrapper function of pt_core_resume_() to avoid TP to be waken/slept
* along with kernel power state even the display is off based on the check of
* TTDL core platform flag.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
static int pt_core_resume(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int rc = 0;
if (cd->drv_debug_suspend || (cd->cpdata->flags & PT_CORE_FLAG_SKIP_SYS_SLEEP))
return 0;
if (pm_suspend_via_firmware() || cd->touch_offload) {
rc = pt_core_restore(cd->dev);
} else {
pt_debug(cd->dev, DL_INFO, "%s start\n", __func__);
rc = pt_enable_i2c_regulator(cd, true);
pt_debug(cd->dev, DL_INFO, "%s i2c regulator rc %d\n", __func__, rc);
}
mutex_lock(&cd->system_lock);
cd->wait_until_wake = 1;
mutex_unlock(&cd->system_lock);
wake_up(&cd->wait_q);
pt_debug(cd->dev, DL_INFO, "%s End rc = %d\n", __func__, rc);
return rc;
}
#endif
#ifdef NEED_SUSPEND_NOTIFIER
/*******************************************************************************
* FUNCTION: pt_pm_notifier
*
* SUMMARY: This function is registered to notifier chain and will perform
* suspend operation if match event PM_SUSPEND_PREPARE.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *nb - pointer to notifier_block structure
* action - notifier event type
* *data - void pointer
******************************************************************************/
static int pt_pm_notifier(struct notifier_block *nb,
unsigned long action, void *data)
{
struct pt_core_data *cd = container_of(nb,
struct pt_core_data, pm_notifier);
if (action == PM_SUSPEND_PREPARE) {
pt_debug(cd->dev, DL_INFO, "%s: Suspend prepare\n",
__func__);
/*
* If PM runtime is not suspended, either call runtime
* PM suspend callback or wait until it finishes
*/
if (!pm_runtime_suspended(cd->dev))
pm_runtime_suspend(cd->dev);
(void) pt_core_suspend(cd->dev);
}
return NOTIFY_DONE;
}
#endif
const struct dev_pm_ops pt_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(pt_core_suspend, pt_core_resume)
.freeze = pt_core_suspend,
.restore = pt_core_restore,
SET_RUNTIME_PM_OPS(pt_core_rt_suspend, pt_core_rt_resume,
NULL)
};
EXPORT_SYMBOL_GPL(pt_pm_ops);
/*******************************************************************************
* FUNCTION: _pt_request_pip2_enter_bl
*
* SUMMARY: Force the DUT to enter the BL by resetting the DUT by use of the
* XRES pin or a soft reset.
*
* NOTE: The WD MUST be stopped/restarted by the calling Function. Having
* the WD active could cause this function to fail!
* NOTE: If start_mode is passed in as PT_MODE_IGNORE, this function
* will not try to determine the current mode but will proceed with
* resetting the DUT and entering the BL.
*
* NOTE: The definition of result code:
* PT_ENTER_BL_PASS (0)
* PT_ENTER_BL_ERROR (1)
* PT_ENTER_BL_RESET_FAIL (2)
* PT_ENTER_BL_HID_START_BL_FAIL (3)
* PT_ENTER_BL_CONFIRM_FAIL (4)
* PT_ENTER_BL_GET_FLASH_INFO_FAIL (5)
*
* RETURNS:
* 0 = success
* !0 = failure
*
*
* PARAMETERS:
* *dev - pointer to device structure
* *start_mode - pointer to the mode the DUT was in when this function
* starts
* *result - pointer to store the result when to enter BL
******************************************************************************/
int _pt_request_pip2_enter_bl(struct device *dev, u8 *start_mode, int *result)
{
int rc = 0;
int t;
int tmp_result = PT_ENTER_BL_ERROR;
int flash_info_retry = 2;
u8 mode = PT_MODE_UNKNOWN;
u8 sys_mode = FW_SYS_MODE_UNDEFINED;
u8 read_buf[32];
u16 actual_read_len;
struct pt_core_data *cd = dev_get_drvdata(dev);
u8 host_mode_cmd[4] = {0xA5, 0xA5, 0xA5, 0xA5};
u8 time = 0;
u8 saved_flashless_auto_bl_mode = cd->flashless_auto_bl;
if (cd->watchdog_enabled) {
pt_debug(dev, DL_WARN,
"%s: Watchdog must be stopped before entering BL\n",
__func__);
goto exit;
}
cancel_work_sync(&cd->enum_work);
cancel_work_sync(&cd->watchdog_work);
/* if undefined assume operational/test to bypass all checks */
if (*start_mode == PT_MODE_IGNORE) {
mode = PT_MODE_OPERATIONAL;
sys_mode = FW_SYS_MODE_TEST;
pt_debug(dev, DL_INFO, "%s: Assume Mode = %d", __func__, mode);
} else if (*start_mode == PT_MODE_UNKNOWN) {
rc = pt_pip2_get_mode_sysmode_(cd, &mode, &sys_mode);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: Get mode failed, mode unknown\n",
__func__);
}
*start_mode = mode;
pt_debug(dev, DL_INFO, "%s: Get Mode = %d", __func__, mode);
} else if (*start_mode == PT_MODE_OPERATIONAL) {
/* Assume SCANNIING mode to avoid doing an extra get_mode */
sys_mode = FW_SYS_MODE_SCANNING;
}
_retry:
/* For Flashless DUTs - Suppress auto BL on next BL sentinel */
pt_debug(dev, DL_INFO, "%s: Flashless Auto_BL - SUPPRESS\n", __func__);
cd->flashless_auto_bl = PT_SUPPRESS_AUTO_BL;
switch (mode) {
case PT_MODE_UNKNOWN:
/*
* When the mode could not be determined the DUT could be
* in App mode running corrupted FW or FW that is not
* responding to the mode request, assume no communication
* and do a hard reset
*/
mutex_lock(&cd->system_lock);
cd->startup_status = STARTUP_STATUS_START;
pt_debug(dev, DL_DEBUG, "%s: Startup Status Reset\n", __func__);
mutex_unlock(&cd->system_lock);
rc = pt_dut_reset(cd, PT_CORE_CMD_UNPROTECTED);
if (rc) {
tmp_result = PT_ENTER_BL_RESET_FAIL;
goto exit;
}
break;
case PT_MODE_OPERATIONAL:
if (sys_mode == FW_SYS_MODE_SCANNING) {
pt_debug(dev, DL_INFO, "%s: Suspend Scanning\n",
__func__);
rc = pt_pip_suspend_scanning_(cd);
if (rc) {
/*
* Print to log but don't exit, the FW could be
* running but be hung or fail to respond to
* this request
*/
pt_debug(dev, DL_ERROR,
"%s Suspend Scan Failed\n", __func__);
}
/* sleep to allow the suspend scan to be processed */
usleep_range(1000, 2000);
}
mutex_lock(&cd->system_lock);
cd->startup_status = STARTUP_STATUS_START;
pt_debug(dev, DL_DEBUG, "%s: Startup Status Reset\n", __func__);
mutex_unlock(&cd->system_lock);
/* Reset device to enter the BL */
rc = pt_dut_reset(cd, PT_CORE_CMD_UNPROTECTED);
if (rc) {
tmp_result = PT_ENTER_BL_RESET_FAIL;
goto exit;
}
break;
case PT_MODE_BOOTLOADER:
/* Do nothing as we are already in the BL */
tmp_result = PT_ENTER_BL_PASS;
goto exit;
default:
/* Should NEVER get here */
tmp_result = PT_ENTER_BL_ERROR;
pt_debug(dev, DL_ERROR, "%s: Unknown mode code\n", __func__);
goto exit;
}
if (!cd->flashless_dut &&
(mode == PT_MODE_UNKNOWN || mode == PT_MODE_OPERATIONAL)) {
/*
* Sending the special "Host Mode" command will instruct the
* BL to not execute the FW it has loaded into RAM.
* The command must be sent within a 40ms window from releasing
* the XRES pin. If the messages is sent too early it will NAK,
* so keep sending it every 2ms until it is accepted by the BL.
* A no-flash DUT does not require this command as there is no
* FW for the BL to load and execute.
*/
usleep_range(4000, 6000);
pt_debug(cd->dev, DL_INFO,
">>> %s: Write Buffer Size[%d] Stay in BL\n",
__func__, (int)sizeof(host_mode_cmd));
pt_pr_buf(cd->dev, DL_DEBUG, host_mode_cmd,
(int)sizeof(host_mode_cmd), ">>> User CMD");
rc = 1;
while (rc && time < 34) {
rc = pt_adap_write_read_specific(cd, 4,
host_mode_cmd, NULL);
usleep_range(1800, 2000);
time += 2;
}
/* Sleep to allow the BL to come up */
usleep_range(1000, 2000);
}
/*
* To avoid the case that next PIP command can be confused by BL/FW
* sentinel's "wakeup" event, chekcing hid_reset_cmd_state which is
* followed by "wakeup event" function can lower the failure rate.
*/
t = wait_event_timeout(cd->wait_q,
((cd->startup_status != STARTUP_STATUS_START)
&& (cd->hid_reset_cmd_state == 0)),
msecs_to_jiffies(300));
if (IS_TMO(t)) {
pt_debug(cd->dev, DL_ERROR,
"%s: TMO waiting for BL sentinel\n", __func__);
}
/* Check if device is now in BL mode */
rc = pt_pip2_get_mode_sysmode_(cd, &mode, NULL);
pt_debug(dev, DL_INFO, "%s: Mode=%d, Status=0x%04X\n", __func__, mode,
cd->startup_status);
if (!rc && mode == PT_MODE_BOOTLOADER) {
pt_debug(dev, DL_INFO, "%s In bootloader mode now\n", __func__);
mutex_lock(&cd->system_lock);
cd->pip2_prot_active = true;
cd->mode = PT_MODE_BOOTLOADER;
mutex_unlock(&cd->system_lock);
tmp_result = PT_ENTER_BL_PASS;
} else {
/*
* If the device doesn't enter BL mode as expected and rc is
* tested pass by above function pt_pip2_get_mode_sysmode_(),
* the function should return an error code to indicate this
* failure PT_ENTER_BL_CONFIRM_FAIL.
*/
if (!rc)
rc = -EINVAL;
tmp_result = PT_ENTER_BL_CONFIRM_FAIL;
mutex_lock(&cd->system_lock);
cd->mode = mode;
mutex_unlock(&cd->system_lock);
pt_debug(dev, DL_ERROR,
"%s ERROR: Not in BL as expected", __func__);
}
exit:
if (!cd->flashless_dut && (tmp_result == PT_ENTER_BL_PASS)) {
/* Check to get (buffered) flash information */
rc = _pt_request_pip2_send_cmd(dev, PT_CORE_CMD_UNPROTECTED,
PIP2_CMD_ID_FLASH_INFO, NULL, 0,
read_buf, &actual_read_len);
if (!rc) {
if (read_buf[PIP2_RESP_BODY_OFFSET] == 0) {
pt_debug(
dev, DL_WARN,
"%s Unavailable Manufacturer ID: 0x%02x\n",
__func__,
read_buf[PIP2_RESP_BODY_OFFSET]);
/*
* If the BL was unable to cache the correct
* values when entering the first time due to
* the Flash part not having been powered up
* long enough, re-enter the BL to trigger the
* BL to re-attempt to cache the values.
*/
if (flash_info_retry-- > 0) {
mode = PT_MODE_UNKNOWN;
pt_debug(dev, DL_WARN,
"%s Assume mode to UNKNOWN to enter BL again, retry=%d\n",
__func__, flash_info_retry);
goto _retry;
} else {
pt_debug(dev, DL_WARN,
"%s Manufacturer ID Unknown\n",
__func__);
tmp_result = PT_ENTER_BL_PASS;
}
}
} else {
tmp_result = PT_ENTER_BL_GET_FLASH_INFO_FAIL;
pt_debug(
dev, DL_ERROR,
"%s: Failed to send PIP2 READ_FLASH_INFO cmd\n",
__func__);
}
}
pt_debug(dev, DL_INFO, "%s Flashless Auto_BL - %s\n", __func__,
saved_flashless_auto_bl_mode == PT_ALLOW_AUTO_BL ? "ALLOW" :
"SUPPRESS");
cd->flashless_auto_bl = saved_flashless_auto_bl_mode;
if (result)
*result = tmp_result;
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_file_open
*
* SUMMARY: Using the BL PIP2 commands open a file and return the file handle
*
* NOTE: The DUT must be in BL mode for this command to work
*
* RETURNS:
* <0 = Error
* >0 = file handle opened
*
* PARAMETERS:
* *dev - pointer to device structure
* file_no - PIP2 file number to open
******************************************************************************/
int _pt_pip2_file_open(struct device *dev, u8 file_no)
{
int ret = 0;
u16 status;
u16 actual_read_len;
u8 file_handle;
u8 data[2];
u8 read_buf[10];
pt_debug(dev, DL_DEBUG, "%s: OPEN file %d\n", __func__, file_no);
data[0] = file_no;
ret = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_FILE_OPEN,
data, 1, read_buf, &actual_read_len);
if (ret) {
pt_debug(dev, DL_ERROR,
"%s ROM BL FILE_OPEN timeout for file = %d\n",
__func__, file_no);
return -PIP2_RSP_ERR_NOT_OPEN;
}
status = read_buf[PIP2_RESP_STATUS_OFFSET];
file_handle = read_buf[PIP2_RESP_BODY_OFFSET];
if (ret || ((status != 0x00) && (status != 0x03)) ||
(file_handle != file_no)) {
pt_debug(dev, DL_ERROR,
"%s ROM BL FILE_OPEN failure: 0x%02X for file = %d\n",
__func__, status, file_handle);
return -status;
}
return file_handle;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_file_close
*
* SUMMARY: Using the BL PIP2 commands close a file
*
* NOTE: The DUT must be in BL mode for this command to work
*
* RETURNS:
* <0 = Error
* >0 = file handle closed
*
* PARAMETERS:
* *dev - pointer to device structure
* file_handle - handle to the file to be closed
******************************************************************************/
int _pt_pip2_file_close(struct device *dev, u8 file_handle)
{
int ret = 0;
u16 status;
u16 actual_read_len;
u8 data[2];
u8 read_buf[32];
pt_debug(dev, DL_DEBUG, "%s: CLOSE file %d\n", __func__, file_handle);
data[0] = file_handle;
ret = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_FILE_CLOSE,
data, 1, read_buf, &actual_read_len);
if (ret) {
pt_debug(dev, DL_ERROR,
"%s ROM BL FILE_CLOSE timeout for file = %d\n",
__func__, file_handle);
return -ETIME;
}
status = read_buf[PIP2_RESP_STATUS_OFFSET];
if (status != 0x00) {
pt_debug(dev, DL_ERROR,
"%s ROM BL FILE_CLOSE failure: 0x%02X for file = %d\n",
__func__, status, file_handle);
return -status;
}
return file_handle;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_file_erase
*
* SUMMARY: Using the BL PIP2 commands erase a file
*
* NOTE: The DUT must be in BL mode for this command to work
* NOTE: Some FLASH parts can time out while erasing one or more sectors,
* one retry is attempted for each sector in a file.
*
* RETURNS:
* <0 = Error
* >0 = file handle closed
*
* PARAMETERS:
* *dev - pointer to device structure
* file_handle - handle to the file to be erased
* *status - PIP2 erase status code
******************************************************************************/
static int _pt_pip2_file_erase(struct device *dev, u8 file_handle, int *status)
{
int ret = 0;
int max_retry = PT_PIP2_MAX_FILE_SIZE/PT_PIP2_FILE_SECTOR_SIZE;
int retry = 1;
u16 actual_read_len;
u8 data[2];
u8 read_buf[10];
struct pt_core_data *cd = dev_get_drvdata(dev);
pt_debug(dev, DL_DEBUG, "%s: ERASE file %d\n", __func__, file_handle);
data[0] = file_handle;
data[1] = PIP2_FILE_IOCTL_CODE_ERASE_FILE;
*status = PIP2_RSP_ERR_TIMEOUT;
/* Increase waiting time for large file erase */
mutex_lock(&cd->system_lock);
cd->pip_cmd_timeout = PT_PIP2_CMD_FILE_ERASE_TIMEOUT;
mutex_unlock(&cd->system_lock);
while (*status == PIP2_RSP_ERR_TIMEOUT && retry < max_retry) {
ret = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_FILE_IOCTL,
data, 2, read_buf, &actual_read_len);
if (ret)
break;
*status = read_buf[PIP2_RESP_STATUS_OFFSET];
if (*status == PIP2_RSP_ERR_TIMEOUT) {
#ifdef TTDL_DIAGNOSTICS
cd->file_erase_timeout_count++;
#endif
pt_debug(dev, DL_WARN,
"%s: ERASE timeout %d for file = %d\n",
__func__, retry, file_handle);
}
retry++;
}
mutex_lock(&cd->system_lock);
cd->pip_cmd_timeout = cd->pip_cmd_timeout_default;
mutex_unlock(&cd->system_lock);
if (ret) {
pt_debug(dev, DL_ERROR,
"%s ROM FILE_ERASE cmd failure: %d for file = %d\n",
__func__, ret, file_handle);
return -EIO;
}
if (*status != 0x00) {
pt_debug(dev, DL_ERROR,
"%s ROM FILE_ERASE failure: 0x%02X for file = %d\n",
__func__, *status, file_handle);
return -EIO;
}
return file_handle;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_file_read
*
* SUMMARY: Using the BL PIP2 commands read n bytes from a already opened file
*
* NOTE: The DUT must be in BL mode for this command to work
*
* RETURNS:
* <0 = Error
* >0 = number of bytes read
*
* PARAMETERS:
* *dev - pointer to device structure
* file_handle - File handle to read from
* num_bytes - number of bytes to read
******************************************************************************/
int _pt_pip2_file_read(struct device *dev, u8 file_handle, u16 num_bytes,
u8 *read_buf)
{
int ret = 0;
u16 status;
u16 actual_read_len;
u8 data[3];
data[0] = file_handle;
data[1] = (num_bytes & 0x00FF);
data[2] = (num_bytes & 0xFF00) >> 8;
ret = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_FILE_READ,
data, 3, read_buf, &actual_read_len);
status = read_buf[PIP2_RESP_STATUS_OFFSET];
if (ret || ((status != 0x00) && (status != 0x03))) {
pt_debug(dev, DL_ERROR,
"%s File open failure with error code = %d\n",
__func__, status);
return -EPERM;
}
ret = num_bytes;
return ret;
}
/*******************************************************************************
* FUNCTION: _pt_read_us_file
*
* SUMMARY: Open a user space file and read 'size' bytes into buf. If size = 0
* then read the entire file.
* NOTE: The file size must be less than PT_PIP2_MAX_FILE_SIZE
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *file_path - pointer to the file path
* *buf - pointer to the buffer to store the file contents
* *size - pointer to the size of the file
******************************************************************************/
int _pt_read_us_file(struct device *dev, u8 *file_path, u8 *buf, int *size)
{
struct file *filp = NULL;
struct inode *inode = NULL;
unsigned int file_len = 0;
unsigned int read_len = 0;
mm_segment_t oldfs;
int rc = 0;
if (file_path == NULL || buf == NULL) {
pt_debug(dev, DL_ERROR, "%s: path || buf is NULL.\n", __func__);
return -EINVAL;
}
pt_debug(dev, DL_WARN, "%s: path = %s\n", __func__, file_path);
oldfs = force_uaccess_begin();
filp = filp_open_block(file_path, O_RDONLY, 0400);
if (IS_ERR(filp)) {
pt_debug(dev, DL_ERROR, "%s: Failed to open %s\n", __func__,
file_path);
rc = -ENOENT;
goto err;
}
if (filp->f_op == NULL) {
pt_debug(dev, DL_ERROR, "%s: File Operation Method Error\n",
__func__);
rc = -EINVAL;
goto exit;
}
inode = filp->f_path.dentry->d_inode;
if (inode == NULL) {
pt_debug(dev, DL_ERROR, "%s: Get inode from filp failed\n",
__func__);
rc = -EINVAL;
goto exit;
}
file_len = i_size_read(inode->i_mapping->host);
if (file_len == 0) {
pt_debug(dev, DL_ERROR, "%s: file size error,file_len = %d\n",
__func__, file_len);
rc = -EINVAL;
goto exit;
}
if (*size == 0)
read_len = file_len;
else
read_len = *size;
if (read_len > PT_PIP2_MAX_FILE_SIZE) {
pt_debug(dev, DL_ERROR, "%s: file size ( %d ) exception.\n",
__func__, read_len);
rc = -EINVAL;
goto exit;
}
filp->private_data = inode->i_private;
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(5, 0, 0))
if (filp->f_op->read(filp, buf, read_len, &(filp->f_pos)) != read_len) {
#else
if (vfs_read(filp, buf, read_len, &(filp->f_pos)) != read_len) {
#endif
pt_debug(dev, DL_ERROR, "%s: file read error.\n", __func__);
rc = -EINVAL;
goto exit;
}
*size = read_len;
exit:
if (filp_close(filp, NULL) != 0)
pt_debug(dev, DL_ERROR, "%s: file close error.\n", __func__);
err:
force_uaccess_end(oldfs);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_request_pip2_bin_hdr
*
* SUMMARY: Read the stored bin file header from Flash or the User Space file
* in the case of a flashless DUT, and parse the contents
*
* RETURNS:
* 0 = Success
* !0 = Error condition
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
int _pt_request_pip2_bin_hdr(struct device *dev, struct pt_bin_file_hdr *hdr)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u8 file_handle;
u8 read_buf[255];
u8 hdr_len = 0;
u8 i;
int bytes_read;
int read_size;
int ret = 0;
int rc = 0;
bool load_hdr_struct = false;
if (cd->flashless_dut) {
read_size = sizeof(read_buf);
rc = _pt_read_us_file(dev, cd->pip2_us_file_path,
read_buf, &read_size);
if (rc) {
ret = rc;
pt_debug(dev, DL_ERROR,
"%s Failed to read fw image from US, rc=%d\n",
__func__, rc);
goto exit;
}
load_hdr_struct = true;
hdr_len = read_buf[0];
i = 0;
} else {
if (cd->mode != PT_MODE_BOOTLOADER) {
ret = -EPERM;
goto exit;
}
/* Open the bin file in Flash */
pt_debug(dev, DL_INFO, "%s Open File 1\n", __func__);
file_handle = _pt_pip2_file_open(dev, PIP2_FW_FILE);
if (file_handle != PIP2_FW_FILE) {
ret = -ENOENT;
pt_debug(dev, DL_ERROR,
"%s Failed to open bin file\n", __func__);
goto exit;
}
/* Read the header length from the file */
pt_debug(dev, DL_INFO, "%s Read length of header\n", __func__);
read_size = 1;
bytes_read = _pt_pip2_file_read(dev, file_handle, read_size,
read_buf);
if (bytes_read != read_size) {
ret = -EX_ERR_FREAD;
pt_debug(dev, DL_ERROR,
"%s Failed to bin file header len\n", __func__);
goto exit_close_file;
}
hdr_len = read_buf[PIP2_RESP_BODY_OFFSET];
if (hdr_len == 0xFF) {
ret = -EX_ERR_FLEN;
pt_debug(dev, DL_ERROR,
"%s Bin header len is invalid\n", __func__);
goto exit_close_file;
}
/* Read the rest of the header from the bin file */
pt_debug(dev, DL_INFO, "%s Read bin file header\n", __func__);
memset(read_buf, 0, sizeof(read_buf));
bytes_read = _pt_pip2_file_read(dev, file_handle, hdr_len,
read_buf);
if (bytes_read != hdr_len) {
ret = -EX_ERR_FREAD;
pt_debug(dev, DL_ERROR,
"%s Failed to read bin file\n", __func__);
goto exit_close_file;
}
load_hdr_struct = true;
exit_close_file:
/* Close the file */
if (file_handle != _pt_pip2_file_close(dev, file_handle)) {
ret = -EX_ERR_FCLOSE;
pt_debug(dev, DL_ERROR,
"%s Failed to close bin file\n", __func__);
}
/*
* The length was already read so subtract 1 to make the rest of
* the offsets match the spec
*/
i = PIP2_RESP_BODY_OFFSET - 1;
}
if (load_hdr_struct) {
hdr->length = hdr_len;
hdr->ttpid = (read_buf[i+1] << 8) | read_buf[i+2];
hdr->fw_major = (read_buf[i+3]);
hdr->fw_minor = (read_buf[i+4]);
hdr->fw_crc = (read_buf[i+5] << 24) |
(read_buf[i+6] << 16) |
(read_buf[i+7] << 8) |
(read_buf[i+8]);
hdr->fw_rev_ctrl = (read_buf[i+9] << 24) |
(read_buf[i+10] << 16) |
(read_buf[i+11] << 8) |
(read_buf[i+12]);
hdr->si_rev = (read_buf[i+14] << 8) | (read_buf[i+13]);
hdr->si_id = (read_buf[i+16] << 8) | (read_buf[i+15]);
hdr->config_ver = (read_buf[i+17] << 8) | (read_buf[i+18]);
if (hdr_len >= 22) {
hdr->hex_file_size = (read_buf[i+19] << 24) |
(read_buf[i+20] << 16) |
(read_buf[i+21] << 8) |
(read_buf[i+22]);
} else {
hdr->hex_file_size = 0;
}
}
exit:
return ret;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_file_get_stats
*
* SUMMARY: Using the BL PIP2 commands get file information from an already
* opened file
*
* NOTE: The DUT must be in BL mode for this command to work
*
* RETURNS:
* !0 = Error
* 0 = Success
*
* PARAMETERS:
* *dev - pointer to device structure
* file_handle - File handle to read from
* *address - pointer to store address of file
* *file_size _ pointer to store size of file
******************************************************************************/
int _pt_pip2_file_get_stats(struct device *dev, u8 file_handle, u32 *address,
u32 *file_size)
{
int ret = 1;
u16 status;
u16 actual_read_len;
u8 data[2];
u8 read_buf[16];
data[0] = file_handle;
data[1] = PIP2_FILE_IOCTL_CODE_FILE_STATS;
ret = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_FILE_IOCTL,
data, 2, read_buf, &actual_read_len);
status = read_buf[PIP2_RESP_STATUS_OFFSET];
if (ret || (status != 0x00)) {
pt_debug(dev, DL_ERROR,
"%s ROM FILE_STATS failure: 0x%02X for file = %d, ret = %d\n",
__func__, status, file_handle, ret);
ret = -EIO;
goto exit;
}
pt_debug(dev, DL_DEBUG,
"%s --- FILE %d Information ---\n", __func__, file_handle);
if (address) {
*address = read_buf[PIP2_RESP_BODY_OFFSET] +
(read_buf[PIP2_RESP_BODY_OFFSET + 1] << 8) +
(read_buf[PIP2_RESP_BODY_OFFSET + 2] << 16) +
(read_buf[PIP2_RESP_BODY_OFFSET + 3] << 24);
pt_debug(dev, DL_DEBUG, "%s Address: 0x%08x\n",
__func__, *address);
}
if (file_size) {
*file_size = read_buf[PIP2_RESP_BODY_OFFSET + 4] +
(read_buf[PIP2_RESP_BODY_OFFSET + 5] << 8) +
(read_buf[PIP2_RESP_BODY_OFFSET + 6] << 16) +
(read_buf[PIP2_RESP_BODY_OFFSET + 7] << 24);
pt_debug(dev, DL_DEBUG, "%s Size : 0x%08x\n",
__func__, *file_size);
}
exit:
return ret;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_file_seek_offset
*
* SUMMARY: Using the BL PIP2 commands seek read/write offset for an already
* opened file
*
* NOTE: The DUT must be in BL mode for this command to work
* NOTE: File open/erase command can reset the offset
*
* RETURNS:
* !0 = Error
* 0 = Success
*
* PARAMETERS:
* *dev - pointer to device structure
* file_handle - File handle to read from
* read_offset - read offset of file
* write_offset - write offset of file
******************************************************************************/
int _pt_pip2_file_seek_offset(struct device *dev, u8 file_handle,
u32 read_offset, u32 write_offset)
{
int ret = 1;
u16 status;
u16 actual_read_len;
u8 data[10];
u8 read_buf[16];
data[0] = file_handle;
data[1] = PIP2_FILE_IOCTL_CODE_SEEK_POINTER;
data[2] = 0xff & read_offset;
data[3] = 0xff & (read_offset >> 8);
data[4] = 0xff & (read_offset >> 16);
data[5] = 0xff & (read_offset >> 24);
data[6] = 0xff & write_offset;
data[7] = 0xff & (write_offset >> 8);
data[8] = 0xff & (write_offset >> 16);
data[9] = 0xff & (write_offset >> 24);
ret = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_FILE_IOCTL,
data, 10, read_buf, &actual_read_len);
status = read_buf[PIP2_RESP_STATUS_OFFSET];
if (ret || (status != 0x00)) {
pt_debug(dev, DL_ERROR,
"%s ROM FILE_SEEK failure: 0x%02X for file = %d, ret = %d\n",
__func__, status, ret, file_handle);
ret = -EIO;
}
return ret;
}
/*******************************************************************************
* FUNCTION: _pt_pip2_file_crc
*
* SUMMARY: Using the BL PIP2 commands to calculate CRC for a file or portion of
* the file.
*
* NOTE: The DUT must be in BL mode for this command to work
* NOTE: This command only can be used for BL version 1.8 or greater.
* BL version 1.8 added this change according to PGV-173.
*
* RETURNS:
* !0 = Error
* 0 = Success
*
* PARAMETERS:
* *dev - pointer to device structure
* file_handle - File handle to read from
* offset - start offset for CRC calculation
* length - number of bytes to calculate CRC over
* read_buf - pointer to the read buffer
******************************************************************************/
int _pt_pip2_file_crc(struct device *dev, u8 file_handle,
u32 offset, u32 length, u8 *read_buf)
{
int rc = 1;
u16 actual_read_len;
u8 data[10];
data[0] = file_handle;
data[1] = PIP2_FILE_IOCTL_CODE_FILE_CRC;
data[2] = 0xff & offset;
data[3] = 0xff & (offset >> 8);
data[4] = 0xff & (offset >> 16);
data[5] = 0xff & (offset >> 24);
data[6] = 0xff & length;
data[7] = 0xff & (length >> 8);
data[8] = 0xff & (length >> 16);
data[9] = 0xff & (length >> 24);
rc = _pt_request_pip2_send_cmd(dev,
PT_CORE_CMD_UNPROTECTED, PIP2_CMD_ID_FILE_IOCTL,
data, 10, read_buf, &actual_read_len);
if (rc)
pt_debug(dev, DL_ERROR,
"%s Return FILE_CRC failure, rc = %d\n",
__func__, rc);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_pip2_ping_test
*
* SUMMARY: BIST type test that uses the PIP2 PING command and ramps up the
* optional payload from 0 bytes to max_bytes and ensures the PIP2
* response payload matches what was sent.
* The max payload size is 247:
* (255 - 2 byte reg address - 4 byte header - 2 byte CRC)
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
int pt_pip2_ping_test(struct device *dev, int max_bytes, int *last_packet_size)
{
u16 actual_read_len;
u8 *read_buf = NULL;
u8 *data = NULL;
int data_offset = PIP2_RESP_STATUS_OFFSET;
int i = 1;
int j = 0;
int rc = 0;
read_buf = kzalloc(PT_MAX_PIP2_MSG_SIZE, GFP_KERNEL);
if (!read_buf)
goto ping_test_exit;
data = kzalloc(PT_MAX_PIP2_MSG_SIZE, GFP_KERNEL);
if (!data)
goto ping_test_exit;
/* Load data payload with an array of walking 1's */
for (i = 0; i < 255; i++)
data[i] = 0x01 << (i % 8);
/* Send 'max_bytes' PING cmds using 'i' bytes as payload for each */
for (i = 0; i <= max_bytes; i++) {
rc = _pt_request_pip2_send_cmd(dev, PT_CORE_CMD_UNPROTECTED,
PIP2_CMD_ID_PING, data, i, read_buf,
&actual_read_len);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: PING failed with %d byte payload\n",
__func__, i);
break;
}
/* Verify data returned matches data sent */
for (j = 0; j < i; j++) {
if (read_buf[data_offset + j] != data[j]) {
pt_debug(dev, DL_DEBUG,
"%s: PING packet size %d: sent[%d]=0x%02X recv[%d]=0x%02X\n",
__func__, i, j, data[j], j,
read_buf[data_offset + j]);
goto ping_test_exit;
}
}
}
ping_test_exit:
*last_packet_size = i - 1;
kfree(read_buf);
kfree(data);
return rc;
}
/*******************************************************************************
* FUNCTION: _pt_ic_parse_input_hex
*
* SUMMARY: Parse a char data array as space delimited hex values into
* an int array.
*
* NOTE: _pt_ic_parse_input() function may have similar work while the type of
* buffer to store data is "u32". This function is still needed by the
* "command" sysfs node because the buffer type to store data is "u8".
*
* RETURN: Length of parsed data
*
* PARAMETERS:
* *dev - pointer to device structure
* *buf - pointer to buffer that holds the input array to parse
* buf_size - size of buf
* *ic_buf - pointer to array to store parsed data
* ic_buf_size - max size of ic_buf
******************************************************************************/
static int _pt_ic_parse_input_hex(struct device *dev, const char *buf,
size_t buf_size, u8 *ic_buf, size_t ic_buf_size)
{
const char *pbuf = buf;
unsigned long value;
char scan_buf[PT_MAX_PIP2_MSG_SIZE + 1];
u32 i = 0;
u32 j;
int last = 0;
int ret;
pt_debug(dev, DL_DEBUG,
"%s: pbuf=%p buf=%p size=%zu %s=%d buf=%s\n",
__func__, pbuf, buf, buf_size, "scan buf size",
PT_MAX_PIP2_MSG_SIZE, buf);
while (pbuf <= (buf + buf_size)) {
if (i >= PT_MAX_PIP2_MSG_SIZE) {
pt_debug(dev, DL_ERROR, "%s: %s size=%d max=%d\n",
__func__, "Max cmd size exceeded", i,
PT_MAX_PIP2_MSG_SIZE);
return -EINVAL;
}
if (i >= ic_buf_size) {
pt_debug(dev, DL_ERROR, "%s: %s size=%d buf_size=%zu\n",
__func__, "Buffer size exceeded", i,
ic_buf_size);
return -EINVAL;
}
while (((*pbuf == ' ') || (*pbuf == ','))
&& (pbuf < (buf + buf_size))) {
last = *pbuf;
pbuf++;
}
if (pbuf >= (buf + buf_size))
break;
memset(scan_buf, 0, PT_MAX_PIP2_MSG_SIZE);
if ((last == ',') && (*pbuf == ',')) {
pt_debug(dev, DL_ERROR, "%s: %s \",,\" not allowed.\n",
__func__, "Invalid data format.");
return -EINVAL;
}
for (j = 0; j < (PT_MAX_PIP2_MSG_SIZE - 1)
&& (pbuf < (buf + buf_size))
&& (*pbuf != ' ')
&& (*pbuf != ','); j++) {
last = *pbuf;
scan_buf[j] = *pbuf++;
}
ret = kstrtoul(scan_buf, 16, &value);
if (ret < 0) {
pt_debug(dev, DL_ERROR,
"%s: %s '%s' %s%s i=%d r=%d\n", __func__,
"Invalid data format. ", scan_buf,
"Use \"0xHH,...,0xHH\"", " instead.",
i, ret);
return ret;
}
ic_buf[i] = value;
pt_debug(dev, DL_DEBUG, "%s: item = %d, value = 0x%02lx",
__func__, i, value);
i++;
}
return i;
}
/*******************************************************************************
* FUNCTION: _pt_ic_parse_input
*
* SUMMARY: Parse user sysfs input data as a space or comma delimited list of
* hex values or dec values into an int array with the following rules:
* 1) Hex values must have a "0x" prefix for each element or the first element
* only
* 2) Dec values do not have any prefix
* 3) It is not allowed to have a mix of dec and hex values in the user input
* string
*
* RETURN: Number of values parsed
*
* PARAMETERS:
* *dev - pointer to device structure
* *buf - pointer to buffer that holds the input array to parse
* buf_size - size of buf
* *out_buf - pointer to array to store parsed data
* out_buf_size - max size of buffer to be stored
******************************************************************************/
static int _pt_ic_parse_input(struct device *dev,
const char *buf, size_t buf_size,
u32 *out_buf, size_t out_buf_size)
{
const char *pbuf = buf;
unsigned long value;
char scan_buf[PT_MAX_PIP2_MSG_SIZE + 1];
u32 i = 0;
u32 j;
int last = 0;
int ret = 0;
u8 str_base = 0;
pt_debug(dev, DL_DEBUG,
"%s: in_buf_size=%zu out_buf_size=%zu %s=%d buf=%s\n",
__func__, buf_size, out_buf_size, "scan buf size",
PT_MAX_PIP2_MSG_SIZE, buf);
while (pbuf <= (buf + buf_size)) {
if (i >= PT_MAX_PIP2_MSG_SIZE) {
pt_debug(dev, DL_ERROR, "%s: %s size=%d max=%d\n",
__func__, "Max cmd size exceeded", i,
PT_MAX_PIP2_MSG_SIZE);
ret = -EINVAL;
goto error;
}
if (i >= out_buf_size) {
pt_debug(dev, DL_ERROR, "%s: %s size=%d buf_size=%zu\n",
__func__, "Buffer size exceeded", i,
out_buf_size);
ret = -EINVAL;
goto error;
}
while (((*pbuf == ' ') || (*pbuf == ','))
&& (pbuf < (buf + buf_size))) {
last = *pbuf;
pbuf++;
}
if (pbuf >= (buf + buf_size))
break;
memset(scan_buf, 0, PT_MAX_PIP2_MSG_SIZE);
if ((last == ',') && (*pbuf == ',')) {
pt_debug(dev, DL_ERROR, "%s: %s \",,\" not allowed.\n",
__func__, "Invalid data format.");
ret = -EINVAL;
goto error;
}
for (j = 0; j < (PT_MAX_PIP2_MSG_SIZE - 1)
&& (pbuf < (buf + buf_size))
&& (*pbuf != ' ')
&& (*pbuf != ','); j++) {
last = *pbuf;
scan_buf[j] = *pbuf++;
}
if (i == 0) {
if ((strncmp(scan_buf, "0x", 2) == 0) ||
(strncmp(scan_buf, "0X", 2) == 0))
str_base = 16;
else
str_base = 10;
} else {
if (((strncmp(scan_buf, "0x", 2) == 0) ||
(strncmp(scan_buf, "0X", 2) == 0)) &&
(str_base == 10)) {
pt_debug(dev, DL_ERROR,
"%s: Decimal and Heximal data mixed\n",
__func__);
ret = -EINVAL;
goto error;
}
}
ret = kstrtoul(scan_buf, str_base, &value);
if (ret < 0) {
pt_debug(dev, DL_ERROR,
"%s: %s '%s' %s%s i=%d r=%d\n", __func__,
"Invalid data format. ", scan_buf,
"Use \"0xHH,...,0xHH\" or \"DD DD DD ... DD\"",
" instead.", i, ret);
goto error;
}
out_buf[i] = value;
pt_debug(dev, DL_DEBUG, "%s: item = %d, value = 0x%02lx(%lu)",
__func__, i, value, value);
i++;
}
ret = i;
error:
return ret;
}
#ifdef TTHE_TUNER_SUPPORT
/*******************************************************************************
* FUNCTION: tthe_debugfs_open
*
* SUMMARY: Open method for tthe_tuner debugfs node. On some hosts the size of
* PT_MAX_PRBUF_SIZE (equal to PAGE_SIZE) is not large enough to handle
* printing a large number of fingers and sensor data without overflowing
* the buffer. tthe_tuner needs ~4K and so the buffer is sized to some
* even multiple of PAGE_SIZE
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *inode - file inode number
* *filp - file pointer to debugfs file
******************************************************************************/
static int tthe_debugfs_open(struct inode *inode, struct file *filp)
{
struct pt_core_data *cd = inode->i_private;
u32 buf_size = PT_MAX_PRBUF_SIZE;
filp->private_data = inode->i_private;
if (cd->tthe_buf)
return -EBUSY;
while (buf_size < 4096)
buf_size = buf_size << 1;
pt_debug(cd->dev, DL_INFO, "%s:PT_MAX_BRBUF_SIZE=%d buf_size=%d\n",
__func__, (int)PT_MAX_PRBUF_SIZE, (int)buf_size);
cd->tthe_buf_size = buf_size;
cd->tthe_buf = kzalloc(cd->tthe_buf_size, GFP_KERNEL);
if (!cd->tthe_buf)
return -ENOMEM;
return 0;
}
/*******************************************************************************
* FUNCTION: tthe_debugfs_close
*
* SUMMARY: Close method for tthe_tuner debugfs node.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *inode - file inode number
* *filp - file pointer to debugfs file
******************************************************************************/
static int tthe_debugfs_close(struct inode *inode, struct file *filp)
{
struct pt_core_data *cd = filp->private_data;
filp->private_data = NULL;
kfree(cd->tthe_buf);
cd->tthe_buf = NULL;
return 0;
}
/*******************************************************************************
* FUNCTION: tthe_debugfs_read
*
* SUMMARY: Read method for tthe_tuner debugfs node. This function prints
* tthe_buf to user buffer.
*
* RETURN: Size of debugfs data print
*
* PARAMETERS:
* *filp - file pointer to debugfs file
* *buf - the user space buffer to read to
* count - the maximum number of bytes to read
* *ppos - the current position in the buffer
******************************************************************************/
static ssize_t tthe_debugfs_read(struct file *filp, char __user *buf,
size_t count, loff_t *ppos)
{
struct pt_core_data *cd = filp->private_data;
int size;
int ret;
static int partial_read;
wait_event_interruptible(cd->wait_q,
cd->tthe_buf_len != 0 || cd->tthe_exit);
mutex_lock(&cd->tthe_lock);
if (cd->tthe_exit) {
mutex_unlock(&cd->tthe_lock);
return 0;
}
if (count > cd->tthe_buf_len)
size = cd->tthe_buf_len;
else
size = count;
if (!size) {
mutex_unlock(&cd->tthe_lock);
return 0;
}
if (partial_read) {
ret = copy_to_user(buf, cd->tthe_buf + partial_read, size);
partial_read = 0;
} else {
ret = copy_to_user(buf, cd->tthe_buf, size);
}
if (size == count)
partial_read = count;
if (ret == size)
return -EFAULT;
size -= ret;
cd->tthe_buf_len -= size;
mutex_unlock(&cd->tthe_lock);
*ppos += size;
return size;
}
static const struct file_operations tthe_debugfs_fops = {
.open = tthe_debugfs_open,
.release = tthe_debugfs_close,
.read = tthe_debugfs_read,
};
#endif
static struct pt_core_nonhid_cmd _pt_core_nonhid_cmd = {
.start_bl = _pt_request_pip_start_bl,
.suspend_scanning = _pt_request_pip_suspend_scanning,
.resume_scanning = _pt_request_pip_resume_scanning,
.get_param = _pt_request_pip_get_param,
.set_param = _pt_request_pip_set_param,
.verify_cfg_block_crc = _pt_request_pip_verify_config_block_crc,
.get_config_row_size = _pt_request_pip_get_config_row_size,
.get_data_structure = _pt_request_pip_get_data_structure,
.run_selftest = _pt_request_pip_run_selftest,
.get_selftest_result = _pt_request_pip_get_selftest_result,
.load_self_test_param = _pt_request_pip_load_self_test_param,
.calibrate_idacs = _pt_request_pip_calibrate_idacs,
.calibrate_ext = _pt_request_pip_calibrate_ext,
.initialize_baselines = _pt_request_pip_initialize_baselines,
.exec_panel_scan = _pt_request_pip_exec_panel_scan,
.retrieve_panel_scan = _pt_request_pip_retrieve_panel_scan,
.read_data_block = _pt_request_pip_read_data_block,
.write_data_block = _pt_request_pip_write_data_block,
.user_cmd = _pt_request_pip_user_cmd,
.get_bl_info = _pt_request_pip_bl_get_information,
.initiate_bl = _pt_request_pip_bl_initiate_bl,
.launch_app = _pt_request_pip_launch_app,
.prog_and_verify = _pt_request_pip_bl_program_and_verify,
.verify_app_integrity = _pt_request_pip_bl_verify_app_integrity,
.get_panel_id = _pt_request_pip_bl_get_panel_id,
.pip2_send_cmd = _pt_request_pip2_send_cmd,
.pip2_send_cmd_no_int = _pt_pip2_send_cmd_no_int,
.pip2_file_open = _pt_pip2_file_open,
.pip2_file_close = _pt_pip2_file_close,
.pip2_file_erase = _pt_pip2_file_erase,
.read_us_file = _pt_read_us_file,
.manage_cal_data = _pt_manage_local_cal_data,
.calc_crc = crc_ccitt_calculate,
#ifdef TTDL_DIAGNOSTICS
.pip2_file_read = _pt_pip2_file_read,
.pip2_file_seek_offset = _pt_pip2_file_seek_offset,
.pip2_file_get_stats = _pt_pip2_file_get_stats,
.pip2_file_crc = _pt_pip2_file_crc,
#endif
};
static struct pt_core_commands _pt_core_commands = {
.subscribe_attention = _pt_subscribe_attention,
.unsubscribe_attention = _pt_unsubscribe_attention,
.request_exclusive = _pt_request_exclusive,
.release_exclusive = _pt_release_exclusive,
.request_reset = _pt_request_reset,
.request_pip2_launch_app = _pt_request_pip2_launch_app,
.request_enum = _pt_request_enum,
.request_sysinfo = _pt_request_sysinfo,
.request_loader_pdata = _pt_request_loader_pdata,
.request_stop_wd = _pt_request_stop_wd,
.request_start_wd = _pt_request_start_wd,
.request_get_mode = _pt_request_get_mode,
.request_active_pip_prot = _pt_request_active_pip_protocol,
.request_pip2_get_mode_sysmode = _pt_request_pip2_get_mode_sysmode,
.request_pip2_enter_bl = _pt_request_pip2_enter_bl,
.request_pip2_bin_hdr = _pt_request_pip2_bin_hdr,
.request_dut_generation = _pt_request_dut_generation,
.request_hw_version = _pt_request_hw_version,
.parse_sysfs_input = _pt_ic_parse_input,
#ifdef TTHE_TUNER_SUPPORT
.request_tthe_print = _pt_request_tthe_print,
#endif
#ifdef TTDL_DIAGNOSTICS
.request_toggle_err_gpio = _pt_request_toggle_err_gpio,
#endif
.nonhid_cmd = &_pt_core_nonhid_cmd,
.request_get_fw_mode = _pt_request_get_fw_sys_mode,
};
struct pt_core_commands *pt_get_commands(void)
{
return &_pt_core_commands;
}
EXPORT_SYMBOL_GPL(pt_get_commands);
static DEFINE_MUTEX(core_list_lock);
static LIST_HEAD(core_list);
static DEFINE_MUTEX(module_list_lock);
static LIST_HEAD(module_list);
static int core_number;
/*******************************************************************************
* FUNCTION: pt_probe_module
*
* SUMMARY: Add the module pointer to module_node and call the probe pointer.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to core data
* *module - pointer to module structure
******************************************************************************/
static int pt_probe_module(struct pt_core_data *cd,
struct pt_module *module)
{
struct module_node *module_node;
int rc = 0;
module_node = kzalloc(sizeof(*module_node), GFP_KERNEL);
if (!module_node)
return -ENOMEM;
module_node->module = module;
mutex_lock(&cd->module_list_lock);
list_add(&module_node->node, &cd->module_list);
mutex_unlock(&cd->module_list_lock);
rc = module->probe(cd->dev, &module_node->data);
if (rc) {
/*
* Remove from the list when probe fails
* in order not to call release
*/
mutex_lock(&cd->module_list_lock);
list_del(&module_node->node);
mutex_unlock(&cd->module_list_lock);
kfree(module_node);
goto exit;
}
exit:
return rc;
}
/*******************************************************************************
* FUNCTION: pt_release_module
*
* SUMMARY: Call the release pointer and remove the module pointer from
* module_list.
*
* PARAMETERS:
* *cd - pointer to core data
* *module - pointer to module structure
******************************************************************************/
static void pt_release_module(struct pt_core_data *cd,
struct pt_module *module)
{
struct module_node *m, *m_n;
mutex_lock(&cd->module_list_lock);
list_for_each_entry_safe(m, m_n, &cd->module_list, node)
if (m->module == module) {
module->release(cd->dev, m->data);
list_del(&m->node);
kfree(m);
break;
}
mutex_unlock(&cd->module_list_lock);
}
/*******************************************************************************
* FUNCTION: pt_probe_modules
*
* SUMMARY: Iterate module_list and probe each module.
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_probe_modules(struct pt_core_data *cd)
{
struct pt_module *m;
int rc = 0;
mutex_lock(&module_list_lock);
list_for_each_entry(m, &module_list, node) {
pt_debug(cd->dev, DL_ERROR, "%s: Probe module %s\n",
__func__, m->name);
rc = pt_probe_module(cd, m);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: Probe fails for module %s\n",
__func__, m->name);
}
mutex_unlock(&module_list_lock);
}
/*******************************************************************************
* FUNCTION: pt_release_modules
*
* SUMMARY: Iterate module_list and remove each module.
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_release_modules(struct pt_core_data *cd)
{
struct pt_module *m;
mutex_lock(&module_list_lock);
list_for_each_entry(m, &module_list, node)
pt_release_module(cd, m);
mutex_unlock(&module_list_lock);
}
/*******************************************************************************
* FUNCTION: pt_get_core_data
*
* SUMMARY: Iterate core_list and get core data.
*
* RETURN:
* pointer to core data or null pointer if fail
*
* PARAMETERS:
* *id - pointer to core id
******************************************************************************/
struct pt_core_data *pt_get_core_data(char *id)
{
struct pt_core_data *d;
list_for_each_entry(d, &core_list, node)
if (!strncmp(d->core_id, id, 20))
return d;
return NULL;
}
EXPORT_SYMBOL_GPL(pt_get_core_data);
/*******************************************************************************
* FUNCTION: pt_add_core
*
* SUMMARY: Add core data to the core_list.
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static void pt_add_core(struct device *dev)
{
struct pt_core_data *d;
struct pt_core_data *cd = dev_get_drvdata(dev);
mutex_lock(&core_list_lock);
list_for_each_entry(d, &core_list, node)
if (d->dev == dev)
goto unlock;
list_add(&cd->node, &core_list);
unlock:
mutex_unlock(&core_list_lock);
}
/*******************************************************************************
* FUNCTION: pt_del_core
*
* SUMMARY: Remove core data from the core_list.
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static void pt_del_core(struct device *dev)
{
struct pt_core_data *d, *d_n;
mutex_lock(&core_list_lock);
list_for_each_entry_safe(d, d_n, &core_list, node)
if (d->dev == dev) {
list_del(&d->node);
goto unlock;
}
unlock:
mutex_unlock(&core_list_lock);
}
/*******************************************************************************
* FUNCTION: pt_register_module
*
* SUMMARY: Register the module to module_list and probe the module for each
* core.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *module - pointer to module structure
******************************************************************************/
int pt_register_module(struct pt_module *module)
{
struct pt_module *m;
struct pt_core_data *cd;
int rc = 0;
if (!module || !module->probe || !module->release)
return -EINVAL;
mutex_lock(&module_list_lock);
list_for_each_entry(m, &module_list, node)
if (m == module) {
rc = -EEXIST;
goto unlock;
}
list_add(&module->node, &module_list);
/* Probe the module for each core */
mutex_lock(&core_list_lock);
list_for_each_entry(cd, &core_list, node)
pt_probe_module(cd, module);
mutex_unlock(&core_list_lock);
unlock:
mutex_unlock(&module_list_lock);
return rc;
}
EXPORT_SYMBOL_GPL(pt_register_module);
/*******************************************************************************
* FUNCTION: pt_unregister_module
*
* SUMMARY: Release the module for each core and remove the module from
* module_list.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *module - pointer to module structure
******************************************************************************/
void pt_unregister_module(struct pt_module *module)
{
struct pt_module *m, *m_n;
struct pt_core_data *cd;
if (!module)
return;
mutex_lock(&module_list_lock);
/* Release the module for each core */
mutex_lock(&core_list_lock);
list_for_each_entry(cd, &core_list, node)
pt_release_module(cd, module);
mutex_unlock(&core_list_lock);
list_for_each_entry_safe(m, m_n, &module_list, node)
if (m == module) {
list_del(&m->node);
break;
}
mutex_unlock(&module_list_lock);
}
EXPORT_SYMBOL_GPL(pt_unregister_module);
/*******************************************************************************
* FUNCTION: pt_get_module_data
*
* SUMMARY: Get module data from module_node by module_list.
*
* RETURN:
* pointer to module data
*
* PARAMETERS:
* *dev - pointer to device structure
* *module - pointer to module structure
******************************************************************************/
void *pt_get_module_data(struct device *dev, struct pt_module *module)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct module_node *m;
void *data = NULL;
mutex_lock(&cd->module_list_lock);
list_for_each_entry(m, &cd->module_list, node)
if (m->module == module) {
data = m->data;
break;
}
mutex_unlock(&cd->module_list_lock);
return data;
}
EXPORT_SYMBOL(pt_get_module_data);
#ifdef CONFIG_HAS_EARLYSUSPEND
/*******************************************************************************
* FUNCTION: pt_early_suspend
*
* SUMMARY: Android PM architecture function that will call "PT_ATTEN_SUSPEND"
* attention list.
*
* PARAMETERS:
* *h - pointer to early_suspend structure
******************************************************************************/
static void pt_early_suspend(struct early_suspend *h)
{
struct pt_core_data *cd =
container_of(h, struct pt_core_data, es);
call_atten_cb(cd, PT_ATTEN_SUSPEND, 0);
}
/*******************************************************************************
* FUNCTION: pt_late_resume
*
* SUMMARY: Android PM architecture function that will call "PT_ATTEN_RESUME"
* attention list.
*
* PARAMETERS:
* *h - pointer to early_suspend structure
******************************************************************************/
static void pt_late_resume(struct early_suspend *h)
{
struct pt_core_data *cd =
container_of(h, struct pt_core_data, es);
call_atten_cb(cd, PT_ATTEN_RESUME, 0);
}
/*******************************************************************************
* FUNCTION: pt_setup_early_suspend
*
* SUMMARY: Register early/suspend function to the system.
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_setup_early_suspend(struct pt_core_data *cd)
{
cd->es.level = EARLY_SUSPEND_LEVEL_BLANK_SCREEN + 1;
cd->es.suspend = pt_early_suspend;
cd->es.resume = pt_late_resume;
register_early_suspend(&cd->es);
}
#elif defined(CONFIG_DRM)
static void pt_resume_work(struct work_struct *work)
{
struct pt_core_data *pt_data = container_of(work, struct pt_core_data,
resume_work);
int rc = 0;
pt_debug(pt_data->dev, DL_INFO, "%s start ", __func__);
if (pt_data->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
return;
rc = pt_core_easywake_off(pt_data);
if (rc < 0) {
pt_debug(pt_data->dev, DL_ERROR,
"%s: Error on wake\n", __func__);
}
pt_debug(pt_data->dev, DL_INFO, "%s touch to wake disabled ", __func__);
return;
}
static void pt_suspend_work(struct work_struct *work)
{
struct pt_core_data *pt_data = container_of(work, struct pt_core_data,
suspend_work);
int rc = 0;
pt_debug(pt_data->dev, DL_INFO, "%s start\n", __func__);
if (pt_data->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
return;
rc = pt_core_easywake_on(pt_data);
if (rc < 0) {
pt_debug(pt_data->dev, DL_ERROR, "%s: Error on sleep\n", __func__);
return;
}
pt_debug(pt_data->dev, DL_INFO, "%s Exit touch to wake enabled\n", __func__);
return;
}
#if defined(CONFIG_PANEL_NOTIFIER)
/*******************************************************************************
* FUNCTION: panel_event_notifier_callback
*
* SUMMARY: Call back function for Panel Event notifier to allow to call
* resume/suspend attention list.
*
* PARAMETERS:
* tag - type of input panel.
* *notification - pointer to notification details.
* *client_data - pointer to core data
******************************************************************************/
static void panel_event_notifier_callback(enum panel_event_notifier_tag tag,
struct panel_event_notification *notification, void *client_data)
{
struct pt_core_data *cd = client_data;
if(!notification)
{
pt_debug(cd->dev,DL_INFO, "%s: Invalid notification\n", __func__);
return;
}
pt_debug(cd->dev, DL_INFO, "%s: DRM notifier called!\n", __func__);
if (cd->quick_boot || cd->drv_debug_suspend)
goto exit;
pt_debug(cd->dev, DL_INFO, "%s: DRM event:%d,fb_state %d",
__func__, notification->notif_type, cd->fb_state);
pt_debug(cd->dev, DL_INFO, "%s: DRM Power - %s - FB state %d ",
__func__, (notification->notif_type == DRM_PANEL_EVENT_UNBLANK)?"UP":"DOWN", cd->fb_state);
if (notification->notif_type == DRM_PANEL_EVENT_UNBLANK) {
pt_debug(cd->dev, DL_INFO, "%s: UNBLANK!\n", __func__);
if (notification->notif_data.early_trigger) {
pr_err("%s: resume: event = %d, not care\n", __func__, notification->notif_type);
pt_debug(cd->dev, DL_INFO, "%s: resume: event = %d, not care\n",
__func__, notification->notif_type);
} else {
pt_debug(cd->dev, DL_INFO, "%s: Resume notifier called!\n",
__func__);
cancel_work_sync(&cd->resume_offload_work);
cancel_work_sync(&cd->suspend_offload_work);
cancel_work_sync(&cd->resume_work);
cancel_work_sync(&cd->suspend_work);
queue_work(cd->pt_workqueue, &cd->resume_work);
#if defined(CONFIG_PM_SLEEP)
pt_debug(cd->dev, DL_INFO, "%s: Resume notifier called!\n",
__func__);
if (cd->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
pt_core_resume_(cd->dev);
#endif
cd->fb_state = FB_ON;
pt_debug(cd->dev, DL_INFO, "%s: Resume notified!\n", __func__);
}
} else if (notification->notif_type == DRM_PANEL_EVENT_BLANK) {
pt_debug(cd->dev, DL_INFO, "%s: BLANK!\n", __func__);
if (notification->notif_data.early_trigger) {
#if defined(CONFIG_PM_SLEEP)
pt_debug(cd->dev, DL_INFO, "%s: Suspend notifier called!\n",
__func__);
if (cd->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
pt_core_suspend_(cd->dev);
#endif
cancel_work_sync(&cd->resume_offload_work);
cancel_work_sync(&cd->suspend_offload_work);
cancel_work_sync(&cd->resume_work);
cancel_work_sync(&cd->suspend_work);
queue_work(cd->pt_workqueue, &cd->suspend_work);
cd->fb_state = FB_OFF;
pt_debug(cd->dev, DL_INFO, "%s: Suspend notified!\n", __func__);
} else {
pt_debug(cd->dev, DL_INFO, "%s: suspend: event = %d, not care\n",
__func__, notification->notif_type);
}
} else if (notification->notif_type == DRM_PANEL_EVENT_BLANK_LP) {
pt_debug(cd->dev, DL_INFO, "%s: LOWPOWER!\n", __func__);
if (notification->notif_data.early_trigger) {
#if defined(CONFIG_PM_SLEEP)
pt_debug(cd->dev, DL_INFO, "%s: Suspend notifier called!\n", __func__);
if (cd->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
pt_core_suspend_(cd->dev);
#endif
cancel_work_sync(&cd->resume_offload_work);
cancel_work_sync(&cd->suspend_offload_work);
cancel_work_sync(&cd->resume_work);
cancel_work_sync(&cd->suspend_work);
queue_work(cd->pt_workqueue, &cd->suspend_work);
cd->fb_state = FB_OFF;
pt_debug(cd->dev, DL_INFO, "%s: Suspend notified!\n", __func__);
} else {
pt_debug(cd->dev, DL_INFO, "%s: suspend: event = %d, not care\n",
__func__, notification->notif_type);
}
} else {
pt_debug(cd->dev, DL_INFO, "%s: DRM BLANK(%d) do not need process\n",
__func__, notification->notif_type);
}
exit:
return;
}
/*******************************************************************************
* FUNCTION: pt_setup_panel_event_notifier
*
* SUMMARY: Set up call back function into drm notifier.
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_setup_panel_event_notifier(struct pt_core_data *cd)
{
void *cookie = NULL;
if (!active_panel)
pt_debug(cd->dev, DL_ERROR,
"%s: Active panel not registered!\n", __func__);
cd->pt_workqueue = create_singlethread_workqueue("ts_wq");
if (!cd->pt_workqueue) {
pt_debug(cd->dev, DL_ERROR,
"%s: worker thread creation failed !\n", __func__);
}
if (cd->pt_workqueue) {
INIT_WORK(&cd->resume_work, pt_resume_work);
INIT_WORK(&cd->suspend_work, pt_suspend_work);
}
cookie = panel_event_notifier_register(PANEL_EVENT_NOTIFICATION_PRIMARY,
PANEL_EVENT_NOTIFIER_CLIENT_PRIMARY_TOUCH,
active_panel,&panel_event_notifier_callback, cd);
if (active_panel && !cookie)
{
pt_debug(cd->dev, DL_ERROR,
"%s: Register notifier failed!\n", __func__);
}
cd->entry = cookie;
}
#else
/*******************************************************************************
* FUNCTION: drm_notifier_callback
*
* SUMMARY: Call back function for DRM notifier to allow to call
* resume/suspend attention list.
*
* RETURN:
* 0 = success
*
* PARAMETERS:
* *self - pointer to notifier_block structure
* event - event type of fb notifier
* *data - pointer to fb_event structure
******************************************************************************/
static int drm_notifier_callback(struct notifier_block *self,
unsigned long event, void *data)
{
struct pt_core_data *cd =
container_of(self, struct pt_core_data, fb_notifier);
struct drm_panel_notifier *evdata = data;
int *blank;
pt_debug(cd->dev, DL_INFO, "%s: DRM notifier called!\n", __func__);
if (!evdata)
goto exit;
if (!(event == DRM_PANEL_EARLY_EVENT_BLANK ||
event == DRM_PANEL_EVENT_BLANK)) {
pt_debug(cd->dev, DL_INFO, "%s: Event(%lu) do not need process\n",
__func__, event);
goto exit;
}
if (cd->quick_boot || cd->drv_debug_suspend)
goto exit;
blank = evdata->data;
pt_debug(cd->dev, DL_INFO, "%s: DRM event:%lu,blank:%d fb_state %d sleep state %d ",
__func__, event, *blank, cd->fb_state, cd->sleep_state);
pt_debug(cd->dev, DL_INFO, "%s: DRM Power - %s - FB state %d ",
__func__, (*blank == DRM_PANEL_BLANK_UNBLANK)?"UP":"DOWN", cd->fb_state);
if (*blank == DRM_PANEL_BLANK_UNBLANK) {
pt_debug(cd->dev, DL_INFO, "%s: UNBLANK!\n", __func__);
if (event == DRM_PANEL_EARLY_EVENT_BLANK) {
pt_debug(cd->dev, DL_INFO, "%s: resume: event = %lu, not care\n",
__func__, event);
} else if (event == DRM_PANEL_EVENT_BLANK) {
if (cd->fb_state != FB_ON) {
pt_debug(cd->dev, DL_INFO, "%s: Resume notifier called!\n",
__func__);
cancel_work_sync(&cd->resume_offload_work);
cancel_work_sync(&cd->suspend_offload_work);
cancel_work_sync(&cd->resume_work);
cancel_work_sync(&cd->suspend_work);
queue_work(cd->pt_workqueue, &cd->resume_work);
#if defined(CONFIG_PM_SLEEP)
pt_debug(cd->dev, DL_INFO, "%s: Resume notifier called!\n",
__func__);
if (cd->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
pt_core_resume_(cd->dev);
#endif
cd->fb_state = FB_ON;
pt_debug(cd->dev, DL_INFO, "%s: Resume notified!\n", __func__);
}
}
} else if (*blank == DRM_PANEL_BLANK_LP || *blank == DRM_PANEL_BLANK_POWERDOWN) {
pt_debug(cd->dev, DL_INFO, "%s: LOWPOWER!\n", __func__);
if (event == DRM_PANEL_EARLY_EVENT_BLANK) {
if (cd->fb_state != FB_OFF) {
#if defined(CONFIG_PM_SLEEP)
pt_debug(cd->dev, DL_INFO, "%s: Suspend notifier called!\n",
__func__);
if (cd->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
pt_core_suspend_(cd->dev);
#endif
cancel_work_sync(&cd->resume_offload_work);
cancel_work_sync(&cd->suspend_offload_work);
cancel_work_sync(&cd->resume_work);
cancel_work_sync(&cd->suspend_work);
queue_work(cd->pt_workqueue, &cd->suspend_work);
cd->fb_state = FB_OFF;
pt_debug(cd->dev, DL_INFO, "%s: Suspend notified!\n", __func__);
}
} else if (event == DRM_PANEL_EVENT_BLANK) {
pt_debug(cd->dev, DL_INFO, "%s: suspend: event = %lu, not care\n",
__func__, event);
}
} else {
pt_debug(cd->dev, DL_INFO, "%s: DRM BLANK(%d) do not need process\n",
__func__, *blank);
}
exit:
return 0;
}
/*******************************************************************************
* FUNCTION: pt_setup_drm_notifier
*
* SUMMARY: Set up call back function into drm notifier.
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_setup_drm_notifier(struct pt_core_data *cd)
{
cd->fb_state = FB_NONE;
cd->fb_notifier.notifier_call = drm_notifier_callback;
pt_debug(cd->dev, DL_INFO, "%s: Setting up drm notifier\n", __func__);
if (!active_panel)
pt_debug(cd->dev, DL_ERROR,
"%s: Active panel not registered!\n", __func__);
cd->pt_workqueue = create_singlethread_workqueue("ts_wq");
if (!cd->pt_workqueue) {
pt_debug(cd->dev, DL_ERROR,
"%s: worker thread creation failed !\n", __func__);
}
if (cd->pt_workqueue) {
INIT_WORK(&cd->resume_work, pt_resume_work);
INIT_WORK(&cd->suspend_work, pt_suspend_work);
}
if (active_panel &&
drm_panel_notifier_register(active_panel,
&cd->fb_notifier) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: Register notifier failed!\n", __func__);
}
#endif
#elif defined(CONFIG_FB)
/*******************************************************************************
* FUNCTION: fb_notifier_callback
*
* SUMMARY: Call back function for FrameBuffer notifier to allow to call
* resume/suspend attention list.
*
* RETURN:
* 0 = success
*
* PARAMETERS:
* *self - pointer to notifier_block structure
* event - event type of fb notifier
* *data - pointer to fb_event structure
******************************************************************************/
static int fb_notifier_callback(struct notifier_block *self,
unsigned long event, void *data)
{
struct pt_core_data *cd =
container_of(self, struct pt_core_data, fb_notifier);
struct fb_event *evdata = data;
int *blank;
if (event != FB_EVENT_BLANK || !evdata)
goto exit;
blank = evdata->data;
if (*blank == FB_BLANK_UNBLANK) {
pt_debug(cd->dev, DL_INFO, "%s: UNBLANK!\n", __func__);
if (cd->fb_state != FB_ON) {
call_atten_cb(cd, PT_ATTEN_RESUME, 0);
#if defined(CONFIG_PM_SLEEP)
if (cd->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
pt_core_resume_(cd->dev);
#endif
cd->fb_state = FB_ON;
}
} else if (*blank == FB_BLANK_POWERDOWN) {
pt_debug(cd->dev, DL_INFO, "%s: POWERDOWN!\n", __func__);
if (cd->fb_state != FB_OFF) {
#if defined(CONFIG_PM_SLEEP)
if (cd->cpdata->flags & PT_CORE_FLAG_SKIP_RUNTIME)
pt_core_suspend_(cd->dev);
#endif
call_atten_cb(cd, PT_ATTEN_SUSPEND, 0);
cd->fb_state = FB_OFF;
}
}
exit:
return 0;
}
/*******************************************************************************
* FUNCTION: pt_setup_fb_notifier
*
* SUMMARY: Set up call back function into fb notifier.
*
* PARAMETERS:
* *cd - pointer to core data
******************************************************************************/
static void pt_setup_fb_notifier(struct pt_core_data *cd)
{
int rc = 0;
cd->fb_state = FB_ON;
cd->fb_notifier.notifier_call = fb_notifier_callback;
rc = fb_register_client(&cd->fb_notifier);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"Unable to register fb_notifier: %d\n", rc);
}
#endif
/*******************************************************************************
* FUNCTION: pt_watchdog_work
*
* SUMMARY: This is where the watchdog work is done except if the DUT is
* sleeping then this function simply returns. If the DUT is awake the
* first thing is to ensure the IRQ is not stuck asserted meaning that
* somehow a response is waiting on the DUT that has not been read. If
* this occurs the message is simply consumed. If or once the IRQ is
* cleared, a PIP PING message is sent to the DUT and if the response
* is received the watchdog succeeds and exits, if no response is seen
* a startup is queued unless the maximum number of startups have already
* been attempted, in that case a BL is attempted.
*
* NOTE: pt_stop_wd_timer() cannot be called within the context of this
* work thread
*
* RETURN: void
*
* PARAMETERS:
* *work - pointer to a work structure for the watchdog work queue
******************************************************************************/
static void pt_watchdog_work(struct work_struct *work)
{
int rc = 0;
struct pt_core_data *cd = container_of(work,
struct pt_core_data, watchdog_work);
/*
* if found the current sleep_state is SS_SLEEPING
* then no need to request_exclusive, directly return
*/
if (cd->sleep_state == SS_SLEEPING)
return;
#ifdef TTDL_DIAGNOSTICS
cd->watchdog_count++;
#endif /* TTDL_DIAGNOSTICS */
/*
* The first WD interval was extended to allow DDI to come up.
* If the WD interval is not the default then adjust timer to the
* current setting. The user can override value with drv_debug sysfs.
*/
if (cd->watchdog_interval != PT_WATCHDOG_TIMEOUT) {
mod_timer_pending(&cd->watchdog_timer, jiffies +
msecs_to_jiffies(cd->watchdog_interval));
}
if (pt_check_irq_asserted(cd)) {
#ifdef TTDL_DIAGNOSTICS
cd->watchdog_irq_stuck_count++;
pt_toggle_err_gpio(cd, PT_ERR_GPIO_IRQ_STUCK);
#endif /* TTDL_DIAGNOSTICS */
pt_debug(cd->dev, DL_ERROR,
"%s: TTDL WD found IRQ asserted, attempt to clear\n",
__func__);
pt_flush_bus(cd, PT_FLUSH_BUS_BASED_ON_LEN, NULL);
}
rc = request_exclusive(cd, cd->dev, PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
goto queue_startup;
}
rc = pt_pip_null_(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n", __func__);
queue_startup:
if (rc) {
#ifdef TTDL_DIAGNOSTICS
cd->watchdog_failed_access_count++;
pt_toggle_err_gpio(cd, PT_ERR_GPIO_EXCLUSIVE_ACCESS);
#endif /* TTDL_DIAGNOSTICS */
pt_debug(cd->dev, DL_ERROR,
"%s: failed to access device in WD, retry count=%d\n",
__func__, cd->startup_retry_count);
/* Already tried FW upgrade because of watchdog but failed */
if (cd->startup_retry_count > PT_WATCHDOG_RETRY_COUNT)
return;
if (cd->startup_retry_count++ < PT_WATCHDOG_RETRY_COUNT) {
/*
* Any wrapper function that trys to disable the
* WD killing this worker cannot be called here.
*/
rc = request_exclusive(cd, cd->dev,
PT_REQUEST_EXCLUSIVE_TIMEOUT);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: fail get exclusive ex=%p own=%p\n",
__func__, cd->exclusive_dev, cd->dev);
goto exit;
}
cd->hw_detected = false;
cd->startup_status = STARTUP_STATUS_START;
pt_debug(cd->dev, DL_DEBUG,
"%s: Startup Status Reset\n", __func__);
rc = pt_dut_reset_and_wait(cd);
if (release_exclusive(cd, cd->dev) < 0)
pt_debug(cd->dev, DL_ERROR,
"%s: fail to release exclusive\n",
__func__);
if (!rc) {
cd->hw_detected = true;
if (!cd->flashless_dut)
pt_queue_enum(cd);
}
#ifdef TTDL_DIAGNOSTICS
cd->wd_xres_count++;
pt_debug(cd->dev, DL_ERROR,
"%s: Comm Failed - DUT reset [#%d]\n",
__func__, cd->wd_xres_count);
#endif /* TTDL_DIAGNOSTICS */
} else {
/*
* After trying PT_WATCHDOG_RETRY_COUNT times to
* reset the part to regain communications, try to BL
*/
pt_debug(cd->dev, DL_ERROR,
"%s: WD DUT access failure, Start FW Upgrade\n",
__func__);
#ifdef TTDL_DIAGNOSTICS
/*
* When diagnostics is enabled allow TTDL to keep
* trying to find the DUT. This allows the DUT to be
* hot swap-able while the host stays running. In
* production this may not be wanted as a customer
* may have several touch drivers and any driver
* that doesn't match the current DUT should give
* up trying and give up using the bus.
*/
pt_debug(cd->dev, DL_INFO,
"%s: Resetting startup_retry_count\n",
__func__);
cd->startup_retry_count = 0;
#endif /* TTDL_DIAGNOSTICS */
/*
* Since fw may be broken,reset sysinfo ready flag
* to let upgrade function work.
*/
mutex_lock(&cd->system_lock);
cd->sysinfo.ready = false;
mutex_unlock(&cd->system_lock);
if (cd->active_dut_generation == DUT_UNKNOWN) {
pt_debug(cd->dev, DL_ERROR,
"%s: Queue Restart\n", __func__);
pt_queue_restart(cd);
} else
kthread_run(start_fw_upgrade, cd, "pt_loader");
}
} else {
cd->hw_detected = true;
if (cd->startup_status <= (STARTUP_STATUS_FW_RESET_SENTINEL |
STARTUP_STATUS_BL_RESET_SENTINEL)) {
pt_debug(cd->dev, DL_ERROR,
"%s: HW detected but not enumerated\n",
__func__);
pt_queue_enum(cd);
}
}
exit:
pt_start_wd_timer(cd);
}
#if (KERNEL_VERSION(4, 14, 0) > LINUX_VERSION_CODE)
/*******************************************************************************
* FUNCTION: pt_watchdog_timer
*
* SUMMARY: The function that is called when the WD timer expires. If the
* watchdog work is not already busy schedule the watchdog work queue.
*
* RETURN: void
*
* PARAMETERS:
* handle - Handle to the watchdog timer
******************************************************************************/
static void pt_watchdog_timer(unsigned long handle)
{
struct pt_core_data *cd = (struct pt_core_data *)handle;
if (!cd)
return;
pt_debug(cd->dev, DL_DEBUG, "%s: Watchdog timer triggered\n",
__func__);
if (!work_pending(&cd->watchdog_work))
schedule_work(&cd->watchdog_work);
}
#else
/*******************************************************************************
* FUNCTION: pt_watchdog_timer
*
* SUMMARY: The function that is called when the WD timer expires. If the
* watchdog work is not already busy schedule the watchdog work queue.
*
* RETURN: void
*
* PARAMETERS:
* *t - Pointer to timer list
******************************************************************************/
static void pt_watchdog_timer(struct timer_list *t)
{
struct pt_core_data *cd = from_timer(cd, t, watchdog_timer);
if (!cd)
return;
pt_debug(cd->dev, DL_DEBUG, "%s: Watchdog timer triggered\n",
__func__);
if (!work_pending(&cd->watchdog_work))
schedule_work(&cd->watchdog_work);
}
#endif
/*******************************************************************************
* Core sysfs show and store functions
******************************************************************************/
/*******************************************************************************
* FUNCTION: pt_hw_version_show
*
* SUMMARY: Gets the HW version for either PIP1.x or PIP2.x DUTS
* Output data format: [SiliconID].[RevID FamilyID].[PanelID]
*
* RETURN: size of data written to sysfs node
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes structure
* *buf - pointer to print output buffer
******************************************************************************/
static ssize_t pt_hw_version_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
_pt_request_hw_version(dev, cd->hw_version);
return scnprintf(buf, PT_MAX_PRBUF_SIZE, "%s\n", cd->hw_version);
}
static DEVICE_ATTR(hw_version, 0444, pt_hw_version_show, NULL);
/*******************************************************************************
* FUNCTION: pt_drv_version_show
*
* SUMMARY: Show method for the drv_version sysfs node that will show the
* TTDL version information
*
* RETURN: Char buffer with printed TTDL version information
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_drv_version_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
return scnprintf(buf, PT_MAX_PRBUF_SIZE,
"Driver: %s\nVersion: %s\nDate: %s\n",
pt_driver_core_name, pt_driver_core_version,
pt_driver_core_date);
}
static DEVICE_ATTR(drv_version, 0444, pt_drv_version_show, NULL);
static DEVICE_ATTR(drv_ver, 0444, pt_drv_version_show, NULL);
/*******************************************************************************
* FUNCTION: pt_fw_version_show
*
* SUMMARY: Show method for the fw_version sysfs node that will
* show the firmware, bootloader and PIP version information
*
* RETURN: Size of printed buffer
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_fw_version_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_ttdata *ttdata;
int rc = 0;
if (cd->mode == PT_MODE_OPERATIONAL)
rc = pt_hid_output_get_sysinfo_(cd);
pt_debug(cd->dev, DL_INFO, "%s: mode = %d sysinfo.ready = %d\n",
__func__, cd->mode, cd->sysinfo.ready);
if (cd->sysinfo.ready)
ttdata = &cd->sysinfo.ttdata;
else
rc = -ENODATA;
if (!rc) {
return scnprintf(buf, strlen(buf),
"Status: %d\n"
"FW : %d.%d.%d\n"
"Config: %d\n"
"BL : %d.%d\n"
"PIP : %d.%d\n",
rc,
ttdata->fw_ver_major, ttdata->fw_ver_minor,
ttdata->revctrl,
ttdata->fw_ver_conf,
ttdata->bl_ver_major, ttdata->bl_ver_minor,
ttdata->pip_ver_major, ttdata->pip_ver_minor);
} else {
return scnprintf(buf, strlen(buf),
"Status: %d\n"
"FW : n/a\n"
"Config: n/a\n"
"BL : n/a\n"
"PIP : n/a\n",
rc);
}
}
static DEVICE_ATTR(fw_version, 0444, pt_fw_version_show, NULL);
/*******************************************************************************
* FUNCTION: pt_sysinfo_show
*
* SUMMARY: Show method for the sysinfo sysfs node that will
* show all the information from get system information command.
*
* RETURN: Size of printed buffer
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_sysinfo_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_sysinfo *si;
struct pt_ttdata *ttdata = NULL;
struct pt_sensing_conf_data *scd = NULL;
int rc = 0;
if (cd->mode == PT_MODE_OPERATIONAL) {
rc = pt_hid_output_get_sysinfo_(cd);
if (cd->sysinfo.ready) {
si = &cd->sysinfo;
ttdata = &si->ttdata;
scd = &si->sensing_conf_data;
} else
rc = -ENODATA;
} else
rc = -EPERM;
pt_debug(cd->dev, DL_INFO, "%s: mode = %d sysinfo.ready = %d\n",
__func__, cd->mode, cd->sysinfo.ready);
if (!rc && ttdata && scd) {
return scnprintf(buf, strlen(buf),
"Status: %d\n"
"pip_ver_major: 0x%02X\n"
"pip_ver_minor: 0x%02X\n"
"fw_pid : 0x%04X\n"
"fw_ver_major : 0x%02X\n"
"fw_ver_minor : 0x%02X\n"
"revctrl : 0x%08X\n"
"fw_ver_conf : 0x%04X\n"
"bl_ver_major : 0x%02X\n"
"bl_ver_minor : 0x%02X\n"
"jtag_id_h : 0x%04X\n"
"jtag_id_l : 0x%04X\n"
"mfg_id[0] : 0x%02X\n"
"mfg_id[1] : 0x%02X\n"
"mfg_id[2] : 0x%02X\n"
"mfg_id[3] : 0x%02X\n"
"mfg_id[4] : 0x%02X\n"
"mfg_id[5] : 0x%02X\n"
"mfg_id[6] : 0x%02X\n"
"mfg_id[7] : 0x%02X\n"
"post_code : 0x%04X\n"
"electrodes_x : 0x%02X\n"
"electrodes_y : 0x%02X\n"
"len_x : 0x%04X\n"
"len_y : 0x%04X\n"
"res_x : 0x%04X\n"
"res_y : 0x%04X\n"
"max_z : 0x%04X\n"
"origin_x : 0x%02X\n"
"origin_y : 0x%02X\n"
"panel_id : 0x%02X\n"
"btn : 0x%02X\n"
"scan_mode : 0x%02X\n"
"max_num_of_tch_per_refresh_cycle: 0x%02X\n",
rc,
ttdata->pip_ver_major,
ttdata->pip_ver_minor,
ttdata->fw_pid,
ttdata->fw_ver_major,
ttdata->fw_ver_minor,
ttdata->revctrl,
ttdata->fw_ver_conf,
ttdata->bl_ver_major,
ttdata->bl_ver_minor,
ttdata->jtag_id_h,
ttdata->jtag_id_l,
ttdata->mfg_id[0],
ttdata->mfg_id[1],
ttdata->mfg_id[2],
ttdata->mfg_id[3],
ttdata->mfg_id[4],
ttdata->mfg_id[5],
ttdata->mfg_id[6],
ttdata->mfg_id[7],
ttdata->post_code,
scd->electrodes_x,
scd->electrodes_y,
scd->len_x,
scd->len_y,
scd->res_x,
scd->res_y,
scd->max_z,
scd->origin_x,
scd->origin_y,
scd->panel_id,
scd->btn,
scd->scan_mode,
scd->max_tch);
} else {
return scnprintf(buf, strlen(buf),
"Status: %d\n",
rc);
}
}
static DEVICE_ATTR(sysinfo, 0444, pt_sysinfo_show, NULL);
/*******************************************************************************
* FUNCTION: pt_hw_reset_show
*
* SUMMARY: The show method for the hw_reset sysfs node that does a hw reset
* by toggling the XRES line and then calls the startup function to
* allow TTDL to re-enumerate the DUT.
* The printed value reflects the status of the full reset/enum.
*
* PARAMETERS:
* *dev - pointer to Device structure
* *attr - pointer to the device attribute structure
* *buf - pointer to buffer to print
******************************************************************************/
static ssize_t pt_hw_reset_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int rc = 0;
int time = 0;
u8 reset_status = 0;
int t;
struct pt_hid_desc hid_desc;
memset(&hid_desc, 0, sizeof(hid_desc));
/* Only allow DUT reset if no active BL in progress */
mutex_lock(&cd->firmware_class_lock);
mutex_lock(&cd->system_lock);
cd->startup_state = STARTUP_NONE;
mutex_unlock(&(cd->system_lock));
pt_stop_wd_timer(cd);
/* ensure no left over exclusive access is still locked */
release_exclusive(cd, cd->dev);
rc = pt_dut_reset(cd, PT_CORE_CMD_PROTECTED);
if (rc) {
mutex_unlock(&cd->firmware_class_lock);
pt_debug(cd->dev, DL_ERROR,
"%s: HW reset failed rc = %d\n", __func__, rc);
goto exit_hw_reset;
}
reset_status |= 0x01 << 0;
if (cd->flashless_dut) {
mutex_unlock(&cd->firmware_class_lock);
t = wait_event_timeout(cd->wait_q, (cd->fw_updating == true),
msecs_to_jiffies(200));
if (IS_TMO(t)) {
pt_debug(dev, DL_ERROR,
"%s: Timeout waiting for FW update",
__func__);
rc = -ETIME;
goto exit_hw_reset;
} else {
pt_debug(dev, DL_INFO,
"%s: ----- Wait FW Loading ----",
__func__);
rc = _pt_request_wait_for_enum_state(
dev, 4000, STARTUP_STATUS_FW_RESET_SENTINEL);
if (rc) {
pt_debug(cd->dev, DL_ERROR,
"%s: No FW Sentinel detected rc = %d\n",
__func__, rc);
goto exit_hw_reset;
}
reset_status |= 0x01 << 1;
}
} else {
/* Wait for any sentinel */
rc = _pt_request_wait_for_enum_state(dev, 150,
STARTUP_STATUS_BL_RESET_SENTINEL |
STARTUP_STATUS_FW_RESET_SENTINEL);
if (rc) {
mutex_unlock(&cd->firmware_class_lock);
pt_debug(cd->dev, DL_ERROR,
"%s: No Sentinel detected rc = %d\n",
__func__, rc);
goto exit_hw_reset;
}
/* sleep needed to ensure no cmd is sent while DUT will NAK */
msleep(30);
if (cd->active_dut_generation == DUT_PIP1_ONLY) {
rc = pt_get_hid_descriptor_(cd, &hid_desc);
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR,
"%s: Error on getting HID descriptor r=%d\n",
__func__, rc);
goto exit_hw_reset;
}
cd->mode = pt_get_mode(cd, &hid_desc);
if (cd->mode == PT_MODE_BOOTLOADER)
rc = pt_hid_output_bl_launch_app_(cd);
} else {
if (cd->mode == PT_MODE_BOOTLOADER)
rc = pt_pip2_launch_app(dev,
PT_CORE_CMD_UNPROTECTED);
}
if (rc) {
mutex_unlock(&cd->firmware_class_lock);
pt_debug(cd->dev, DL_ERROR,
"%s: PIP launch app failed rc = %d\n",
__func__, rc);
goto exit_hw_reset;
}
mutex_unlock(&cd->firmware_class_lock);
reset_status |= 0x01 << 1;
msleep(20);
if ((cd->active_dut_generation == DUT_UNKNOWN) ||
(cd->mode != PT_MODE_OPERATIONAL))
pt_queue_restart(cd);
else
pt_queue_enum(cd);
}
while (!(cd->startup_status & STARTUP_STATUS_COMPLETE) && time < 2000) {
msleep(50);
pt_debug(cd->dev, DL_INFO,
"%s: wait %dms for 0x%04X, current enum=0x%04X\n",
__func__, time, STARTUP_STATUS_COMPLETE,
cd->startup_status);
time += 50;
}
if (!(cd->startup_status & STARTUP_STATUS_COMPLETE)) {
rc = -ETIME;
goto exit_hw_reset;
}
pt_debug(cd->dev, DL_INFO, "%s: HW Reset complete. enum=0x%04X\n",
__func__, cd->startup_status);
reset_status |= 0x01 << 2;
pt_start_wd_timer(cd);
exit_hw_reset:
return scnprintf(buf, strlen(buf),
"Status: %d\n"
"Reset Status: 0x%02X\n", rc, reset_status);
}
static DEVICE_ATTR(hw_reset, 0444, pt_hw_reset_show, NULL);
/*******************************************************************************
* FUNCTION: pt_pip2_cmd_rsp_store
*
* SUMMARY: This is the store method for the raw PIP2 cmd/rsp sysfs node. Any
* raw PIP2 command echo'd to this node will be sent directly to the DUT.
* Command byte order:
* Byte [0] - PIP2 command ID
* Byte [1-n] - PIP2 command payload
*
* RETURN: Size of passed in buffer
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to buffer that hold the command parameters
* size - size of buf
******************************************************************************/
static ssize_t pt_pip2_cmd_rsp_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u16 actual_read_len;
u8 input_data[PT_MAX_PIP2_MSG_SIZE + 1];
u8 read_buf[PT_MAX_PIP2_MSG_SIZE + 1];
u8 pip2_cmd_id = 0x00;
u8 *pip2_cmd_data = NULL;
int data_len = 0;
int length;
int rc = 0;
/* clear shared data */
mutex_lock(&cd->sysfs_lock);
cd->raw_cmd_status = 0;
cd->cmd_rsp_buf_len = 0;
memset(cd->cmd_rsp_buf, 0, sizeof(cd->cmd_rsp_buf));
mutex_unlock(&cd->sysfs_lock);
length = _pt_ic_parse_input_hex(dev, buf, size,
input_data, PT_MAX_PIP2_MSG_SIZE);
if (length <= 0 || length > (PT_MAX_PIP2_MSG_SIZE - 2)) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
}
/* Send PIP2 command if enough data was provided */
if (length >= 1) {
pip2_cmd_id = input_data[0];
pip2_cmd_data = &input_data[1];
data_len = length - 1;
rc = _pt_request_pip2_send_cmd(dev, PT_CORE_CMD_PROTECTED,
pip2_cmd_id, pip2_cmd_data, data_len,
read_buf, &actual_read_len);
cd->raw_cmd_status = rc;
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: PIP2 cmd 0x%02x failed rc = %d\n",
__func__, pip2_cmd_id, rc);
goto exit;
} else {
cd->cmd_rsp_buf_len = actual_read_len;
memcpy(cd->cmd_rsp_buf, read_buf, actual_read_len);
pt_debug(dev, DL_ERROR,
"%s: PIP2 actual_read_len = %d\n",
__func__, actual_read_len);
}
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR,
"%s: Insufficient data provided for PIP2 cmd\n",
__func__);
}
exit:
if (rc)
return rc;
return size;
}
/*******************************************************************************
* FUNCTION: pt_pip2_cmd_rsp_show
*
* SUMMARY: The show method for the raw pip2_cmd_rsp sysfs node. Any PIP2
* response generated after using the store method of the pip2_cmd_rsp
* sysfs node, are available to be read here.
*
* PARAMETERS:
* *dev - pointer to Device structure
* *attr - pointer to the device attribute structure
* *buf - pointer to buffer to print
******************************************************************************/
static ssize_t pt_pip2_cmd_rsp_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int i;
ssize_t data_len;
int index;
mutex_lock(&cd->sysfs_lock);
index = scnprintf(buf, PT_MAX_PRBUF_SIZE,
"Status: %d\n", cd->raw_cmd_status);
if (cd->raw_cmd_status)
goto error;
/* Remove the CRC from the length of the response */
data_len = cd->cmd_rsp_buf_len - 2;
/* Start printing from the data payload */
for (i = PIP1_RESP_COMMAND_ID_OFFSET; i < data_len; i++)
index += scnprintf(buf + index, PT_MAX_PRBUF_SIZE - index,
"%02X ", cd->cmd_rsp_buf[i]);
if (data_len >= PIP1_RESP_COMMAND_ID_OFFSET) {
index += scnprintf(buf + index, PT_MAX_PRBUF_SIZE - index,
"\n(%zd bytes)\n",
data_len - PIP1_RESP_COMMAND_ID_OFFSET);
} else {
index += scnprintf(buf + index, PT_MAX_PRBUF_SIZE - index,
"\n(%zd bytes)\n", 0);
}
error:
mutex_unlock(&cd->sysfs_lock);
return index;
}
static DEVICE_ATTR(pip2_cmd_rsp, 0644, pt_pip2_cmd_rsp_show,
pt_pip2_cmd_rsp_store);
/*******************************************************************************
* FUNCTION: pt_command_store
*
* SUMMARY: This is the store method for the raw PIP command sysfs node. Any
* raw PIP command echo'd to this node will be sent directly to the DUT.
* TTDL will not parse the command.
*
* RETURN: Size of passed in buffer
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to buffer that hold the command parameters
* size - size of buf
******************************************************************************/
static ssize_t pt_command_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
unsigned short crc;
u16 actual_read_len;
u8 input_data[PT_MAX_PIP2_MSG_SIZE + 1];
int length;
int len_field;
int rc = 0;
mutex_lock(&cd->sysfs_lock);
cd->cmd_rsp_buf_len = 0;
memset(cd->cmd_rsp_buf, 0, sizeof(cd->cmd_rsp_buf));
mutex_unlock(&cd->sysfs_lock);
length = _pt_ic_parse_input_hex(dev, buf, size,
input_data, PT_MAX_PIP2_MSG_SIZE);
if (length <= 0 || length > PT_MAX_PIP2_MSG_SIZE) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto pt_command_store_exit;
}
/* PIP2 messages begin with 01 01 */
if (length >= 2 && input_data[0] == 0x01 && input_data[1] == 0x01) {
cd->pip2_prot_active = 1;
/* Override next seq tag with what was sent */
cd->pip2_cmd_tag_seq = input_data[4] & 0x0F;
/* For PIP2 cmd if length does not include crc, add it */
len_field = (input_data[3] << 8) | input_data[2];
if (len_field == length && length <= 254) {
crc = crc_ccitt_calculate(&input_data[2],
length - 2);
pt_debug(dev, DL_ERROR, "%s: len=%d crc=0x%02X\n",
__func__, length, crc);
input_data[length] = (crc & 0xFF00) >> 8;
input_data[length + 1] = crc & 0x00FF;
length = length + 2;
}
}
/* write PIP command to log */
pt_pr_buf(dev, DL_INFO, input_data, length, "command_buf");
pm_runtime_get_sync(dev);
rc = pt_hid_output_user_cmd(cd, PT_MAX_INPUT, cd->cmd_rsp_buf,
length, input_data, &actual_read_len);
pm_runtime_put(dev);
mutex_lock(&cd->sysfs_lock);
cd->raw_cmd_status = rc;
if (rc) {
cd->cmd_rsp_buf_len = 0;
pt_debug(dev, DL_ERROR, "%s: Failed to send command: %s\n",
__func__, buf);
} else {
cd->cmd_rsp_buf_len = actual_read_len;
}
cd->pip2_prot_active = 0;
mutex_unlock(&cd->sysfs_lock);
pt_command_store_exit:
if (rc)
return rc;
return size;
}
static DEVICE_ATTR(command, 0220, NULL, pt_command_store);
/*******************************************************************************
* FUNCTION: pt_response_show
*
* SUMMARY: The show method for the raw PIP response sysfs node. Any PIP
* response generated after using the pt_command_store sysfs node, are
* available to be read here.
*
* PARAMETERS:
* *dev - pointer to Device structure
* *attr - pointer to the device attribute structure
* *buf - pointer to buffer to print
******************************************************************************/
static ssize_t pt_response_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int i;
ssize_t num_read;
int index;
mutex_lock(&cd->sysfs_lock);
index = scnprintf(buf, PT_MAX_PRBUF_SIZE,
"Status: %d\n", cd->raw_cmd_status);
if (cd->raw_cmd_status)
goto error;
num_read = cd->cmd_rsp_buf_len;
for (i = 0; i < num_read; i++)
index += scnprintf(buf + index, PT_MAX_PRBUF_SIZE - index,
"0x%02X\n", cd->cmd_rsp_buf[i]);
index += scnprintf(buf + index, PT_MAX_PRBUF_SIZE - index,
"(%zd bytes)\n", num_read);
error:
mutex_unlock(&cd->sysfs_lock);
return index;
}
static DEVICE_ATTR(response, 0444, pt_response_show, NULL);
/*******************************************************************************
* FUNCTION: pt_dut_debug_show
*
* SUMMARY: Show method for the dut_debug sysfs node. Shows what parameters
* are available for the store method.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_dut_debug_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
ssize_t ret;
ret = scnprintf(buf, strlen(buf),
"Status: 0\n"
"dut_debug sends the following commands to the DUT:\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
,
PIP1_BL_CMD_ID_VERIFY_APP_INTEGRITY, "", "BL Verify APP",
PT_DUT_DBG_HID_RESET, "", "HID Reset",
PT_DUT_DBG_HID_SET_POWER_ON, "", "HID SET_POWER ON",
PT_DUT_DBG_HID_SET_POWER_SLEEP, "", "HID SET_POWER SLEEP",
PT_DUT_DBG_HID_SET_POWER_STANDBY, "", "HID SET_POWER STANDBY",
PIP1_BL_CMD_ID_GET_INFO, "", "BL Get Info",
PIP1_BL_CMD_ID_PROGRAM_AND_VERIFY, "", "BL Program & Verify",
PIP1_BL_CMD_ID_LAUNCH_APP, "", "BL Launch APP",
PIP1_BL_CMD_ID_INITIATE_BL, "", "BL Initiate BL",
PT_DUT_DBG_PIP_SOFT_RESET, "", "PIP Soft Reset",
PT_DUT_DBG_RESET, "", "Toggle the TP_XRES GPIO",
PT_DUT_DBG_PIP_NULL, "", "PIP NULL (PING)",
PT_DUT_DBG_PIP_ENTER_BL, "", "PIP enter BL",
PT_DUT_DBG_HID_SYSINFO, "", "HID system info",
PT_DUT_DBG_PIP_SUSPEND_SCAN, "", "Suspend Scan",
PT_DUT_DBG_PIP_RESUME_SCAN, "", "Resume Scan",
PT_DUT_DBG_HID_DESC, "", "Get HID Desc"
);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_drv_debug_show
*
* SUMMARY: Show method for the drv_debug sysfs node. Shows what parameters
* are available for the store method.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_drv_debug_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
ssize_t ret;
ret = scnprintf(buf, strlen(buf),
"Status: 0\n"
"drv_debug supports the following values:\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s - %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
#ifdef TTDL_DIAGNOSTICS
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
#endif /* TTDL_DIAGNOSTICS */
"%d %s \t- %s\n"
#ifdef TTDL_DIAGNOSTICS
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
"%d %s \t- %s\n"
#endif /* TTDL_DIAGNOSTICS */
,
PT_DRV_DBG_SUSPEND, " ", "Suspend TTDL responding to INT",
PT_DRV_DBG_RESUME, " ", "Resume TTDL responding to INT",
PT_DRV_DBG_STOP_WD, " ", "Stop TTDL WD",
PT_DRV_DBG_START_WD, " ", "Start TTDL WD",
PT_DRV_DBG_TTHE_TUNER_EXIT, " ", "Exit TTHE Tuner Logging",
PT_DRV_DBG_TTHE_BUF_CLEAN, " ", "Clear TTHE Tuner buffer",
PT_DRV_DBG_CLEAR_PARM_LIST, " ", "Clear RAM Param list",
PT_DRV_DBG_FORCE_BUS_READ, " ", "Force bus read",
PT_DRV_DBG_CLEAR_CAL_DATA, " ", "Clear CAL Cache",
PT_DRV_DBG_REPORT_LEVEL, "[0|1|2|3|4]", "Set TTDL Debug Level",
PT_DRV_DBG_WATCHDOG_INTERVAL, "[n] ", "TTDL WD Interval in ms",
PT_DRV_DBG_SHOW_TIMESTAMP, "[0|1]", "Show Timestamps"
#ifdef TTDL_DIAGNOSTICS
, PT_DRV_DBG_SETUP_PWR, "[0|1]", "Power DUT up/down",
PT_DRV_DBG_GET_PUT_SYNC, "[0|1]", "Get/Put Linux Sleep",
PT_DRV_DBG_SET_TT_DATA, "[0|1]", "Display TT_DATA"
#endif /* TTDL_DIAGNOSTICS */
, PT_DRV_DBG_SET_GENERATION, "[0|1|2]", "Set DUT generation"
#ifdef TTDL_DIAGNOSTICS
, PT_DRV_DBG_SET_BRIDGE_MODE, "[0|1]", "On/Off Bridge Mode",
PT_DRV_DBG_SET_I2C_ADDRESS, "[0-127]", "I2C DUT Address",
PT_DRV_DBG_SET_FLASHLESS_DUT, "[0|1]", "Flashless DUT yes/no",
PT_DRV_DBG_SET_FORCE_SEQ, "[8-15]", "Force PIP2 Sequence #",
PT_DRV_DBG_BL_WITH_NO_INT, "[0|1]", "BL with no INT",
PT_DRV_DBG_CAL_CACHE_IN_HOST, "[0|1]", "CAL Cache in host",
PT_DRV_DBG_MULTI_CHIP, "[0|1]", "Multi Chip Support",
PT_DRV_DBG_PIP_TIMEOUT, "[100-7000]", "PIP Resp Timeout (ms)",
PT_DRV_DBG_TTHE_HID_USB_FORMAT, "[0|1]",
"TTHE_TUNER HID USB Format"
#endif /* TTDL_DIAGNOSTICS */
);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_drv_debug_store
*
* SUMMARY: Currently the store method for both sysfs nodes: drv_debug and
* dut_debug. Drv_debug will contain all functionality that can be run
* without a DUT preset and is available anytime TTDL is running.
* Dut_debug requires a DUT to be available and will only be created after
* a DUT has been detected.
* This function will eventually be split into two but until the overlap
* has been depricated this function contains all commands that can be
* used for TTDL/DUT debugging status and control.
* All commands require at least one value to be passed in *buf with some
* requiring two.
*
* RETURN: Size of passed in buffer
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to buffer that hold the command parameters
* size - size of buf
******************************************************************************/
static ssize_t pt_drv_debug_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
unsigned long value;
int rc = 0;
u8 return_data[8];
static u8 wd_disabled;
u32 input_data[3];
int length;
#ifdef TTDL_DIAGNOSTICS
struct i2c_client *client = to_i2c_client(dev);
unsigned short crc = 0;
u16 cal_size;
#endif
input_data[0] = 0;
input_data[1] = 0;
/* Maximmum input is two elements */
length = _pt_ic_parse_input(dev, buf, size,
input_data, ARRAY_SIZE(input_data));
if (length < 1 || length > 2) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto pt_drv_debug_store_exit;
}
value = input_data[0];
if (length == 1) {
pt_debug(dev, DL_DEBUG,
"%s: Debug Cmd Received (id=%d)\n",
__func__, input_data[0]);
} else if (length == 2) {
pt_debug(dev, DL_DEBUG,
"%s: Debug Cmd Received (id=%d, data=%d)\n",
__func__, input_data[0], input_data[1]);
} else {
pt_debug(dev, DL_DEBUG,
"%s: Invalid arguments received\n", __func__);
rc = -EINVAL;
goto pt_drv_debug_store_exit;
}
/* Start watchdog timer command */
if (value == PT_DRV_DBG_START_WD) {
pt_debug(dev, DL_INFO, "%s: Cmd: Start Watchdog\n", __func__);
wd_disabled = 0;
cd->watchdog_force_stop = false;
pt_start_wd_timer(cd);
goto pt_drv_debug_store_exit;
}
/* Stop watchdog timer temporarily */
pt_stop_wd_timer(cd);
if (value == PT_DRV_DBG_STOP_WD) {
pt_debug(dev, DL_INFO, "%s: Cmd: Stop Watchdog\n", __func__);
wd_disabled = 1;
cd->watchdog_force_stop = true;
goto pt_drv_debug_store_exit;
}
switch (value) {
case PT_DRV_DBG_SUSPEND: /* 4 */
pt_debug(dev, DL_INFO, "%s: TTDL: Core Sleep\n", __func__);
wd_disabled = 1;
rc = pt_core_suspend_(cd->dev);
if (rc)
pt_debug(dev, DL_ERROR, "%s: Suspend failed rc=%d\n",
__func__, rc);
else {
pt_debug(dev, DL_INFO, "%s: Suspend succeeded\n",
__func__);
cd->drv_debug_suspend = true;
pt_debug(dev, DL_INFO, "%s: Debugfs flag set:\n", __func__);
}
break;
case PT_DRV_DBG_RESUME: /* 5 */
pt_debug(dev, DL_INFO, "%s: TTDL: Wake\n", __func__);
rc = pt_core_resume_(cd->dev);
if (rc)
pt_debug(dev, DL_ERROR, "%s: Resume failed rc=%d\n",
__func__, rc);
else {
pt_debug(dev, DL_INFO, "%s: Resume succeeded\n",
__func__);
cd->drv_debug_suspend = false;
pt_debug(dev, DL_INFO, "%s: Debugfs flag reset:\n", __func__);
}
break;
case PIP1_BL_CMD_ID_VERIFY_APP_INTEGRITY: /* BL - 49 */
pt_debug(dev, DL_INFO, "%s: Cmd: verify app integ\n", __func__);
pt_hid_output_bl_verify_app_integrity(cd, &return_data[0]);
break;
case PT_DUT_DBG_HID_RESET: /* 50 */
pt_debug(dev, DL_INFO, "%s: Cmd: hid_reset\n", __func__);
pt_hid_cmd_reset(cd);
break;
case PT_DUT_DBG_HID_SET_POWER_ON: /* 53 */
pt_debug(dev, DL_INFO, "%s: Cmd: hid_set_power_on\n", __func__);
pt_hid_cmd_set_power(cd, HID_POWER_ON);
wd_disabled = 0;
break;
case PT_DUT_DBG_HID_SET_POWER_SLEEP: /* 54 */
pt_debug(dev, DL_INFO, "%s: Cmd: hid_set_power_off\n",
__func__);
wd_disabled = 1;
pt_hid_cmd_set_power(cd, HID_POWER_SLEEP);
break;
case PT_DUT_DBG_HID_SET_POWER_STANDBY: /* 55 */
pt_debug(dev, DL_INFO, "%s: Cmd: hid_set_power_standby\n",
__func__);
wd_disabled = 1;
pt_hid_cmd_set_power(cd, HID_POWER_STANDBY);
break;
case PIP1_BL_CMD_ID_GET_INFO: /* BL - 56 */
pt_debug(dev, DL_INFO, "%s: Cmd: bl get info\n", __func__);
pt_hid_output_bl_get_information(cd, return_data);
break;
case PIP1_BL_CMD_ID_PROGRAM_AND_VERIFY: /* BL - 57 */
pt_debug(dev, DL_INFO, "%s: Cmd: program and verify\n",
__func__);
pt_hid_output_bl_program_and_verify(cd, 0, NULL);
break;
case PIP1_BL_CMD_ID_LAUNCH_APP: /* BL - 59 */
pt_debug(dev, DL_INFO, "%s: Cmd: launch app\n", __func__);
pt_hid_output_bl_launch_app(cd);
break;
case PIP1_BL_CMD_ID_INITIATE_BL: /* BL - 72 */
pt_debug(dev, DL_INFO, "%s: Cmd: initiate bl\n", __func__);
pt_hid_output_bl_initiate_bl(cd, 0, NULL, 0, NULL);
break;
case PT_DUT_DBG_PIP_SOFT_RESET: /* 97 */
pt_debug(dev, DL_INFO, "%s: Cmd: Soft Reset\n", __func__);
rc = pt_hw_soft_reset(cd, PT_CORE_CMD_PROTECTED);
break;
case PT_DUT_DBG_RESET: /* 98 */
pt_debug(dev, DL_INFO, "%s: Cmd: Hard Reset\n", __func__);
rc = pt_hw_hard_reset(cd);
break;
case PT_DUT_DBG_PIP_NULL: /* 100 */
pt_debug(dev, DL_INFO, "%s: Cmd: Ping (null)\n", __func__);
pt_pip_null(cd);
break;
case PT_DUT_DBG_PIP_ENTER_BL: /* 101 */
pt_debug(dev, DL_INFO, "%s: Cmd: start_bootloader\n", __func__);
rc = pt_pip_start_bootloader(cd);
if (!rc) {
cd->startup_status = STARTUP_STATUS_BL_RESET_SENTINEL;
cd->mode = PT_MODE_BOOTLOADER;
}
break;
case PT_DUT_DBG_HID_SYSINFO: /* 102 */
pt_debug(dev, DL_INFO, "%s: Cmd: get_sysinfo\n", __func__);
pt_hid_output_get_sysinfo(cd);
break;
case PT_DUT_DBG_PIP_SUSPEND_SCAN: /* 103 */
pt_debug(dev, DL_INFO, "%s: Cmd: suspend_scanning\n", __func__);
pt_pip_suspend_scanning(cd);
break;
case PT_DUT_DBG_PIP_RESUME_SCAN: /* 104 */
pt_debug(dev, DL_INFO, "%s: Cmd: resume_scanning\n", __func__);
pt_pip_resume_scanning(cd);
break;
#ifdef TTHE_TUNER_SUPPORT
case PT_DRV_DBG_TTHE_TUNER_EXIT: /* 107 */
cd->tthe_exit = 1;
wake_up(&cd->wait_q);
kfree(cd->tthe_buf);
cd->tthe_buf = NULL;
cd->tthe_exit = 0;
break;
case PT_DRV_DBG_TTHE_BUF_CLEAN: /* 108 */
if (cd->tthe_buf)
memset(cd->tthe_buf, 0, PT_MAX_PRBUF_SIZE);
else
pt_debug(dev, DL_INFO, "%s : tthe_buf not existed\n",
__func__);
break;
#endif
#ifdef TTDL_DIAGNOSTICS
case PT_DUT_DBG_HID_DESC: /* 109 */
pt_debug(dev, DL_INFO, "%s: Cmd: get_hid_desc\n", __func__);
pt_get_hid_descriptor(cd, &cd->hid_desc);
break;
case PT_DRV_DBG_CLEAR_PARM_LIST: /* 110 */
pt_debug(dev, DL_INFO, "%s: TTDL: Clear Parameter List\n",
__func__);
pt_erase_parameter_list(cd);
break;
case PT_DRV_DBG_FORCE_BUS_READ: /* 111 */
rc = pt_read_input(cd);
if (!rc)
pt_parse_input(cd);
break;
case PT_DRV_DBG_CLEAR_CAL_DATA: /* 112 */
rc = _pt_manage_local_cal_data(dev, PT_CAL_DATA_CLEAR,
&cal_size, &crc);
if (rc)
pt_debug(dev, DL_ERROR,
"%s: CAL Data clear failed rc=%d\n",
__func__, rc);
else
pt_debug(dev, DL_INFO,
"%s: CAL Cleared, Chip ID=0x%04X size=%d\n",
__func__, crc, size);
break;
case PT_DRV_DBG_REPORT_LEVEL: /* 200 */
mutex_lock(&cd->system_lock);
if (input_data[1] >= 0 && input_data[1] < DL_MAX) {
cd->debug_level = input_data[1];
pt_debug(dev, DL_INFO, "%s: Set debug_level: %d\n",
__func__, cd->debug_level);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid debug_level: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
#endif
case PT_DRV_DBG_WATCHDOG_INTERVAL: /* 201 */
mutex_lock(&cd->system_lock);
if (input_data[1] > 100) {
cd->watchdog_interval = input_data[1];
pt_debug(dev, DL_INFO,
"%s: Set watchdog_ interval to: %d\n",
__func__, cd->watchdog_interval);
pt_start_wd_timer(cd);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR,
"%s: Invalid watchdog interval: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
#ifdef TTDL_DIAGNOSTICS
case PT_DRV_DBG_SHOW_TIMESTAMP: /* 202 */
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->show_timestamp = 0;
pt_debug(dev, DL_INFO, "%s: Disable show_timestamp\n",
__func__);
} else if (input_data[1] == 1) {
cd->show_timestamp = 1;
pt_debug(dev, DL_INFO, "%s: Enable show_timestamp\n",
__func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR,
"%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_SETUP_PWR: /* 205 */
if (input_data[1] == 0) {
cd->cpdata->setup_power(cd->cpdata,
PT_MT_POWER_OFF, cd->dev);
pt_debug(dev, DL_INFO,
"%s: Initiate Power Off\n", __func__);
} else if (input_data[1] == 1) {
cd->cpdata->setup_power(cd->cpdata,
PT_MT_POWER_ON, cd->dev);
pt_debug(dev, DL_INFO,
"%s: Initiate Power On\n", __func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR,
"%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
break;
case PT_DRV_DBG_GET_PUT_SYNC: /* 206 */
if (input_data[1] == 0) {
pm_runtime_put(dev);
pt_debug(dev, DL_ERROR,
"%s: Force call pm_runtime_put()\n", __func__);
} else if (input_data[1] == 1) {
pm_runtime_get_sync(dev);
pt_debug(dev, DL_ERROR,
"%s: Force call pm_runtime_get_sync()\n",
__func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR,
"%s: WARNING: Invalid parameter: %d\n",
__func__, input_data[1]);
}
break;
case PT_DRV_DBG_SET_TT_DATA: /* 208 */
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->show_tt_data = false;
pt_debug(dev, DL_INFO,
"%s: Disable TT_DATA\n", __func__);
} else if (input_data[1] == 1) {
cd->show_tt_data = true;
pt_debug(dev, DL_INFO,
"%s: Enable TT_DATA\n", __func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR,
"%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_SET_GENERATION: /* 210 */
if (input_data[1] == cd->active_dut_generation) {
mutex_lock(&cd->system_lock);
cd->set_dut_generation = true;
mutex_unlock(&(cd->system_lock));
} else {
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->active_dut_generation = DUT_UNKNOWN;
cd->set_dut_generation = false;
} else if (input_data[1] == 1) {
cd->active_dut_generation = DUT_PIP1_ONLY;
cd->set_dut_generation = true;
} else if (input_data[1] == 2) {
cd->active_dut_generation = DUT_PIP2_CAPABLE;
cd->set_dut_generation = true;
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR,
"%s: Invalid parameter: %d\n",
__func__, input_data[1]);
break;
}
cd->startup_status = STARTUP_STATUS_START;
pt_debug(cd->dev, DL_DEBUG,
"%s: Startup Status Reset\n", __func__);
mutex_unlock(&(cd->system_lock));
pt_debug(dev, DL_INFO,
"%s: Active DUT Generation Set to: %d\n",
__func__, cd->active_dut_generation);
/* Changing DUT generations full restart needed */
pt_queue_restart(cd);
}
break;
case PT_DRV_DBG_SET_BRIDGE_MODE: /* 211 */
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->bridge_mode = false;
pt_debug(dev, DL_INFO,
"%s: Disable Bridge Mode\n", __func__);
} else if (input_data[1] == 1) {
cd->bridge_mode = true;
pt_debug(dev, DL_INFO,
"%s: Enable Bridge Mode\n", __func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_SET_I2C_ADDRESS: /* 212 */
mutex_lock(&cd->system_lock);
/* Only a 7bit address is valid */
if (input_data[1] >= 0 && input_data[1] <= 0x7F) {
client->addr = input_data[1];
pt_debug(dev, DL_INFO,
"%s: Set I2C Address: 0x%2X\n",
__func__, client->addr);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid I2C Address %d\n",
__func__, input_data[1]);
client->addr = 0x24;
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_SET_FLASHLESS_DUT: /* 213 */
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->flashless_dut = 0;
cd->flashless_auto_bl = PT_SUPPRESS_AUTO_BL;
pt_debug(dev, DL_INFO, "%s: Disable FLAHLESS DUT\n",
__func__);
} else if (input_data[1] == 1) {
cd->flashless_dut = 1;
cd->flashless_auto_bl = PT_ALLOW_AUTO_BL;
pt_debug(dev, DL_INFO, "%s: Enable FLAHLESS DUT\n",
__func__);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_SET_FORCE_SEQ: /* 214 */
mutex_lock(&cd->system_lock);
if (input_data[1] >= 0x8 && input_data[1] <= 0xF) {
cd->force_pip2_seq = input_data[1];
cd->pip2_cmd_tag_seq = input_data[1];
pt_debug(dev, DL_INFO,
"%s: Force PIP2 Seq to: 0x%02X\n",
__func__, input_data[1]);
} else {
cd->force_pip2_seq = 0;
pt_debug(dev, DL_INFO,
"%s: Clear Forced PIP2 Seq\n", __func__);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_BL_WITH_NO_INT: /* 215 */
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->bl_with_no_int = 0;
pt_debug(dev, DL_INFO, "%s: BL using IRQ\n", __func__);
} else if (input_data[1] == 1) {
cd->bl_with_no_int = 1;
pt_debug(dev, DL_INFO, "%s: BL using Polling\n",
__func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_CAL_CACHE_IN_HOST: /* 216 */
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->cal_cache_in_host = PT_FEATURE_DISABLE;
pt_debug(dev, DL_INFO,
"%s: Disable Calibration cache in host\n",
__func__);
} else if (input_data[1] == 1) {
cd->cal_cache_in_host = PT_FEATURE_ENABLE;
pt_debug(dev, DL_INFO,
"%s: Enable Calibration cache in host\n",
__func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_MULTI_CHIP: /* 217 */
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->multi_chip = PT_FEATURE_DISABLE;
cd->ttdl_bist_select = 0x07;
pt_debug(dev, DL_INFO,
"%s: Disable Multi-chip support\n", __func__);
} else if (input_data[1] == 1) {
cd->multi_chip = PT_FEATURE_ENABLE;
cd->ttdl_bist_select = 0x3F;
pt_debug(dev, DL_INFO,
"%s: Enable Multi-chip support\n", __func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_SET_PANEL_ID_TYPE: /* 218 */
mutex_lock(&cd->system_lock);
if (input_data[1] <= 0x07) {
cd->panel_id_support = input_data[1];
pt_debug(dev, DL_INFO,
"%s: Set panel_id_support to %d\n",
__func__, cd->panel_id_support);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_PIP_TIMEOUT: /* 219 */
mutex_lock(&cd->system_lock);
if (input_data[1] >= 100 && input_data[1] <= 7000) {
/*
* The timeout is changed for some cases so the
* pip_cmd_timeout_default is used to retore back to
* what the user requested as the new timeout.
*/
cd->pip_cmd_timeout_default = input_data[1];
cd->pip_cmd_timeout = input_data[1];
pt_debug(dev, DL_INFO,
"%s: PIP Timeout = %d\n", __func__,
cd->pip_cmd_timeout_default);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
case PT_DRV_DBG_TTHE_HID_USB_FORMAT: /* 220 */
mutex_lock(&cd->system_lock);
if (input_data[1] == 0) {
cd->tthe_hid_usb_format = PT_FEATURE_DISABLE;
pt_debug(dev, DL_INFO,
"%s: Disable tthe_tuner HID-USB format\n",
__func__);
} else if (input_data[1] == 1) {
cd->tthe_hid_usb_format = PT_FEATURE_ENABLE;
pt_debug(dev, DL_INFO,
"%s: Enable tthe_tuner HID-USB format\n",
__func__);
} else {
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid parameter: %d\n",
__func__, input_data[1]);
}
mutex_unlock(&(cd->system_lock));
break;
#endif /* TTDL_DIAGNOSTICS */
default:
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid value\n", __func__);
}
/* Enable watchdog timer */
if (!wd_disabled)
pt_start_wd_timer(cd);
pt_drv_debug_store_exit:
if (rc)
return rc;
return size;
}
static DEVICE_ATTR(drv_debug, 0644, pt_drv_debug_show,
pt_drv_debug_store);
/*******************************************************************************
* FUNCTION: pt_sleep_status_show
*
* SUMMARY: Show method for the sleep_status sysfs node that will show the
* sleep status as either ON or OFF
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_sleep_status_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret;
mutex_lock(&cd->system_lock);
if (cd->sleep_state == SS_SLEEP_ON)
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "off\n");
else
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "on\n");
mutex_unlock(&cd->system_lock);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_panel_id_show
*
* SUMMARY: Show method for the panel_id sysfs node that will show the
* detected panel ID from the DUT
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_panel_id_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret;
u8 pid = PANEL_ID_NOT_ENABLED;
int rc = 0;
if (cd->active_dut_generation == DUT_PIP1_ONLY) {
/*
* The DUT should report the same panel ID from both the BL and
* the FW unless the panel_id feature is set to only
* PT_PANEL_ID_BY_SYS_INFO, in which case the BL is not able
* to retrieve the panel_id.
*/
if (cd->mode == PT_MODE_BOOTLOADER) {
/*
* Return the stored value if PT_PANEL_ID_BY_BL
* is not supported while other feature exits.
*/
if (cd->panel_id_support & PT_PANEL_ID_BY_BL) {
rc = pt_hid_output_bl_get_panel_id_(cd, &pid);
if (rc) {
pt_debug(dev, DL_ERROR, "%s: %s %s\n",
"Failed to retrieve Panel ID. ",
"Using cached value\n",
__func__);
}
}
} else if (cd->mode == PT_MODE_OPERATIONAL) {
if (cd->panel_id_support &
(PT_PANEL_ID_BY_BL | PT_PANEL_ID_BY_SYS_INFO)) {
/* For all systems sysinfo has the panel_id */
rc = pt_hid_output_get_sysinfo(cd);
if (!rc)
pid =
cd->sysinfo.sensing_conf_data.panel_id;
pt_debug(dev, DL_ERROR,
"%s: Gen6 FW mode rc=%d PID=0x%02X\n",
__func__, rc, pid);
}
} else {
pt_debug(dev, DL_ERROR, "%s: Active mode unknown\n",
__func__);
rc = -EPERM;
}
} else if (cd->active_dut_generation == DUT_PIP2_CAPABLE) {
if (cd->mode == PT_MODE_BOOTLOADER) {
if (cd->panel_id_support & PT_PANEL_ID_BY_BL) {
rc = _pt_pip2_get_panel_id_by_gpio(cd, &pid);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: BL get panel ID failed rc=%d\n",
__func__, rc);
}
}
} else if (cd->mode == PT_MODE_OPERATIONAL) {
if (cd->panel_id_support &
(PT_PANEL_ID_BY_BL | PT_PANEL_ID_BY_SYS_INFO)) {
rc = pt_hid_output_get_sysinfo(cd);
if (!rc)
pid =
cd->sysinfo.sensing_conf_data.panel_id;
pt_debug(dev, DL_ERROR,
"%s: TT/TC FW mode rc=%d PID=0x%02X\n",
__func__, rc, pid);
}
} else {
pt_debug(dev, DL_ERROR, "%s: Active mode unknown\n",
__func__);
rc = -EPERM;
}
} else {
pt_debug(dev, DL_ERROR, "%s: Dut generation is unknown\n",
__func__);
rc = -EPERM;
}
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: %d\n0x%02X\n",
rc, pid);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_get_param_store
*
* SUMMARY: Store method for the get_param sysfs node. Stores what parameter
* ID to retrieve with the show method.
*
* NOTE: This sysfs node is only available after a DUT has been enumerated
*
* RETURN: Size of passed in buffer if successful
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
* size - size of buf
******************************************************************************/
static ssize_t pt_get_param_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u32 input_data[2];
int length;
int rc = 0;
/* Maximum input of one value */
length = _pt_ic_parse_input(dev, buf, size, input_data,
ARRAY_SIZE(input_data));
if (length != 1) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
}
mutex_lock(&cd->system_lock);
cd->get_param_id = input_data[0];
mutex_unlock(&(cd->system_lock));
exit:
if (rc)
return rc;
return size;
}
/*******************************************************************************
* FUNCTION: pt_get_param_show
*
* SUMMARY: Show method for the get_param sysfs node. Retrieves the
* parameter data from the DUT based on the ID stored in the core
* data variable "get_param_id". If the ID is invalid, the DUT cannot
* communicate or some other error occures, an error status is returned
* with no value following.
* Output is in the form:
* Status: x
* 0xyyyyyyyy
* The 32bit data will only follow the status code if the status == 0
*
* NOTE: This sysfs node is only available after a DUT has been enumerated
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_get_param_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret = 0;
int status;
u32 value = 0;
status = pt_pip_get_param(cd, cd->get_param_id, &value);
if (status) {
pt_debug(dev, DL_ERROR, "%s: %s Failed, status = %d\n",
__func__, "pt_get_param", status);
ret = scnprintf(buf, strlen(buf),
"%s %d\n",
"Status:", status);
} else {
pt_debug(dev, DL_DEBUG, "%s: Param [%d] = 0x%04X\n",
__func__, cd->get_param_id, value);
ret = scnprintf(buf, strlen(buf),
"Status: %d\n"
"0x%04X\n",
status, value);
}
return ret;
}
/*******************************************************************************
* FUNCTION: pt_ttdl_restart_show
*
* SUMMARY: Show method for ttdl_restart sysfs node. This node releases all
* probed modules, calls startup() and then re-probes modules.
*
* RETURN: size of data written to sysfs node
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes structure
* *buf - pointer to print output buffer
******************************************************************************/
static ssize_t pt_ttdl_restart_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
int t;
int rc = 0;
mutex_lock(&cd->system_lock);
cd->startup_state = STARTUP_NONE;
mutex_unlock(&(cd->system_lock));
/* ensure no left over exclusive access is still locked */
release_exclusive(cd, cd->dev);
pt_queue_restart(cd);
t = wait_event_timeout(cd->wait_q,
(cd->startup_status >= STARTUP_STATUS_COMPLETE),
msecs_to_jiffies(PT_REQUEST_ENUM_TIMEOUT));
if (IS_TMO(t)) {
pt_debug(cd->dev, DL_ERROR,
"%s: TMO waiting for FW sentinel\n", __func__);
rc = -ETIME;
}
return scnprintf(buf, strlen(buf),
"Status: %d\n"
"Enum Status: 0x%04X\n", rc, cd->startup_status);
}
static DEVICE_ATTR(ttdl_restart, 0444, pt_ttdl_restart_show, NULL);
/*******************************************************************************
* FUNCTION: pt_pip2_gpio_read_show
*
* SUMMARY: Sends a PIP2 READ_GPIO command to the DUT and prints the
* contents of the response to the passed in output buffer.
*
* RETURN: size of data written to sysfs node
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes structure
* *buf - pointer to print output buffer
******************************************************************************/
static ssize_t pt_pip2_gpio_read_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u8 status = 0;
u32 gpio_value = 0;
int rc = 0;
/* This functionality is only available in the BL */
if (cd->mode == PT_MODE_BOOTLOADER)
rc = pt_pip2_read_gpio(dev, &status, &gpio_value);
else
rc = -EPERM;
if (!rc) {
if (status == 0)
return scnprintf(buf, PT_MAX_PRBUF_SIZE,
"Status: %d\n"
"DUT GPIO Reg: 0x%08X\n",
rc, gpio_value);
else
return scnprintf(buf, PT_MAX_PRBUF_SIZE,
"Status: %d\n"
"DUT GPIO Reg: n/a\n",
status);
} else
return scnprintf(buf, PT_MAX_PRBUF_SIZE,
"Status: %d\n"
"DUT GPIO Reg: n/a\n",
rc);
}
/*******************************************************************************
* FUNCTION: pt_device_exit
*
* SUMMARY: Remove functon for the I2C module
*
* PARAMETERS:
* *client - pointer to i2c client structure
******************************************************************************/
#ifdef PT_AMBIENT_MODE
static int pt_device_exit(struct i2c_client *client)
{
struct pt_core_data *cd = i2c_get_clientdata(client);
struct device *dev = cd->dev;
void *glink_pt_send_msg;
int glink_touch_enter = TOUCH_ENTER;
pt_debug(dev, DL_INFO,"%s: Start pt_device_exit\n", __func__);
glink_pt_send_msg = &glink_touch_enter;
pt_debug(dev, DL_INFO, "[touch]glink_pt_send_msg = %0x\n", glink_pt_send_msg);
glink_touch_tx_msg(glink_pt_send_msg, TOUCH_MSG_SIZE);
if (active_panel)
panel_event_notifier_unregister(cd->entry);
pt_core_state = STATE_SUSPEND;
pm_runtime_suspend(dev);
pm_runtime_disable(dev);
pt_stop_wd_timer(cd);
call_atten_cb(cd, PT_ATTEN_CANCEL_LOADER, 0);
cancel_work_sync(&cd->ttdl_restart_work);
cancel_work_sync(&cd->enum_work);
cancel_work_sync(&cd->resume_offload_work);
cancel_work_sync(&cd->suspend_offload_work);
cancel_work_sync(&cd->resume_work);
cancel_work_sync(&cd->suspend_work);
pt_stop_wd_timer(cd);
device_init_wakeup(dev, 0);
disable_irq_nosync(cd->irq);
if (cd->cpdata->setup_irq)
cd->cpdata->setup_irq(cd->cpdata, PT_MT_IRQ_FREE, dev);
if (cd->cpdata->init)
cd->cpdata->init(cd->cpdata, PT_MT_POWER_OFF, dev);
if (cd->cpdata->setup_power)
cd->cpdata->setup_power(cd->cpdata, PT_MT_POWER_OFF, dev);
pt_debug(dev, DL_INFO,"%s: End pt_device_exit \n", __func__);
return 0;
}
#endif
/*******************************************************************************
* FUNCTION: pt_touch_offload_store
*
* SUMMARY: The store method for the touch_offload sysfs node that allows the TTDL
* to be enabled/disabled.
*
* RETURN: Size of passed in buffer
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to buffer that hold the command parameters
* size - size of buf
******************************************************************************/
static ssize_t pt_touch_offload_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct i2c_client *client = to_i2c_client(dev);
u32 input_data[2];
int length;
int rc = 0;
/* Maximum input of one value */
length = _pt_ic_parse_input(dev, buf, size, input_data, ARRAY_SIZE(input_data));
if (length != 1) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n", __func__);
rc = -EINVAL;
goto exit;
}
switch (input_data[0]) {
case 0:
pt_debug(dev, DL_ERROR, "%s: TTDL: Core Touch Offload OFF\n", __func__);
cd->touch_offload = true;
rc = pt_device_exit(client);
if (rc)
pt_debug(dev, DL_ERROR, "%s: Power off error detected rc=%d\n",
__func__, rc);
else {
cd->touch_offload = true;
pt_debug(dev, DL_ERROR, "%s: Debugfs PT DEVICE EXIT flag set:\n",
__func__);
}
break;
case 1:
pt_debug(dev, DL_ERROR, "%s: TTDL: Core Touch Offload ON\n", __func__);
rc = pt_device_entry(&client->dev, client->irq, PT_DATA_SIZE);
if (rc)
pt_debug(dev, DL_ERROR, "%s: Power on error detected rc=%d\n",
__func__, rc);
else {
cd->touch_offload = false;
pt_debug(dev, DL_ERROR, "%s: Debugfs PT DEVICE ENTRY flag set:\n",
__func__);
}
break;
default:
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid value\n", __func__);
}
exit:
if (rc)
return rc;
return size;
}
/*******************************************************************************
* FUNCTION: pt_touch_offload_show
*
* SUMMARY: The show method for the touch_offload sysfs node that allows the TTDL
* to verify touch offload enable or disabled.
*
* RETURN: size of data written to sysfs node
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to print output buffer
******************************************************************************/
static ssize_t pt_touch_offload_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return scnprintf(buf, PT_MAX_PRBUF_SIZE,
"Touch offload : %s\n",
(cd->touch_offload)? "Enabled" : "Disabled");
}
/*******************************************************************************
* FUNCTION: pt_pip2_version_show
*
* SUMMARY: Sends a PIP2 VERSION command to the DUT and prints the
* contents of the response to the passed in output buffer.
*
* RETURN: size of data written to sysfs node
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes structure
* *buf - pointer to print output buffer
******************************************************************************/
static ssize_t pt_pip2_version_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
int rc = 0;
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_ttdata *ttdata = &cd->sysinfo.ttdata;
rc = pt_pip2_get_version(cd);
if (!rc) {
return scnprintf(buf, PT_MAX_PRBUF_SIZE,
"PIP VERSION : %02X.%02X\n"
"BL VERSION : %02X.%02X\n"
"FW VERSION : %02X.%02X\n"
"SILICON ID : %04X.%04X\n"
"UID : 0x%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X\n",
ttdata->pip_ver_major, ttdata->pip_ver_minor,
ttdata->bl_ver_major, ttdata->bl_ver_minor,
ttdata->fw_ver_major, ttdata->fw_ver_minor,
ttdata->chip_id, ttdata->chip_rev,
ttdata->uid[0], ttdata->uid[1],
ttdata->uid[2], ttdata->uid[3],
ttdata->uid[4], ttdata->uid[5],
ttdata->uid[6], ttdata->uid[7],
ttdata->uid[8], ttdata->uid[9],
ttdata->uid[10], ttdata->uid[11]);
} else {
pt_debug(dev, DL_ERROR,
"%s: Failed to retriev PIP2 VERSION data\n", __func__);
return scnprintf(buf, PT_MAX_PRBUF_SIZE,
"PIP VERSION : -\n"
"BL VERSION : -\n"
"FW VERSION : -\n"
"SILICON ID : -\n"
"UID : -\n");
}
}
#ifdef TTDL_DIAGNOSTICS
/*******************************************************************************
* FUNCTION: pt_ttdl_status_show
*
* SUMMARY: Show method for the ttdl_status sysfs node. Displays TTDL internal
* variable states and GPIO levels. Additional information printed when
* TTDL_DIAGNOSTICS is enabled.
*
* NOTE: All counters will be reset to 0 when this function is called.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_ttdl_status_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_platform_data *pdata = dev_get_platdata(dev);
struct i2c_client *client = to_i2c_client(dev);
ssize_t ret;
u16 cal_size = 0;
unsigned short crc = 0;
if (cd->cal_cache_in_host)
_pt_manage_local_cal_data(dev,
PT_CAL_DATA_INFO, &cal_size, &crc);
ret = scnprintf(buf, strlen(buf),
"%s: 0x%04X\n"
"%s: %d\n"
"%s: %s\n"
"%s: %s %s\n"
"%s: %s\n"
"%s: 0x%02X\n"
"%s: %s\n"
"%s: %s\n"
"%s: %s\n"
"%s: %s\n"
"%s: %d\n"
"%s: %d\n"
"%s: %s\n"
"%s: %s\n"
"%s: %d\n"
#ifdef TTDL_DIAGNOSTICS
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %s\n"
"%s: %s\n"
"%s: %s\n"
"%s: %d\n"
"%s: 0x%04X\n"
"%s: %s\n"
#endif /* TTDL_DIAGNOSTICS */
,
"Startup Status ", cd->startup_status,
"TTDL Debug Level ", cd->debug_level,
"Mode ",
cd->mode ? (cd->mode == PT_MODE_OPERATIONAL ?
"Operational" : "BL") : "Unknown",
"DUT Generation ",
cd->active_dut_generation ?
(cd->active_dut_generation == DUT_PIP2_CAPABLE ?
"PT TC/TT" : "Gen5/6") : "Unknown",
cd->active_dut_generation ?
(cd->set_dut_generation == true ?
"(Set)" : "(Detected)") : "",
"HW Detected ",
cd->hw_detected ? "True" : "False",
"I2C Address ",
cd->bus_ops->bustype == BUS_I2C ? client->addr : 0,
"Active Bus Module ",
cd->bus_ops->bustype == BUS_I2C ? "I2C" : "SPI",
"Flashless Mode ",
cd->flashless_dut == 1 ? "Yes" : "No",
"GPIO state - IRQ ",
cd->cpdata->irq_stat ?
(cd->cpdata->irq_stat(cd->cpdata, dev) ?
"High" : "Low") : "not defined",
"GPIO state - TP_XRES ",
pdata->core_pdata->rst_gpio ?
(gpio_get_value(pdata->core_pdata->rst_gpio) ?
"High" : "Low") : "not defined",
"RAM Parm restore list ", pt_count_parameter_list(cd),
"Startup Retry Count ", cd->startup_retry_count,
"WD - Manual Force Stop ",
cd->watchdog_force_stop ? "True" : "False",
"WD - Enabled ",
cd->watchdog_enabled ? "True" : "False",
"WD - Interval (ms) ", cd->watchdog_interval
#ifdef TTDL_DIAGNOSTICS
, "WD - Triggered Count ", cd->watchdog_count,
"WD - IRQ Stuck low count ", cd->watchdog_irq_stuck_count,
"WD - Device Access Errors ", cd->watchdog_failed_access_count,
"WD - XRES Count ", cd->wd_xres_count,
"IRQ Triggered Count ", cd->irq_count,
"BL Packet Retry Count ", cd->bl_retry_packet_count,
"PIP2 CRC Error Count ", cd->pip2_crc_error_count,
"Bus Transmit Error Count ", cd->bus_transmit_error_count,
"File Erase Timeout Count ", cd->file_erase_timeout_count,
"Error GPIO trigger type ", cd->err_gpio_type,
"Exclusive Access Lock ", cd->exclusive_dev ? "Set":"Free",
"Suppress No-Flash Auto BL ",
cd->flashless_auto_bl == PT_SUPPRESS_AUTO_BL ?
"Yes" : "No",
"Calibration Cache on host ",
cd->cal_cache_in_host == PT_FEATURE_ENABLE ?
"Yes" : "No",
"Calibration Cache size ", cal_size,
"Calibration Cache chip ID ", crc,
"Multi-Chip Support ",
cd->multi_chip == PT_FEATURE_ENABLE ? "Yes" : "No"
#endif /* TTDL_DIAGNOSTICS */
);
#ifdef TTDL_DIAGNOSTICS
/* Reset all diagnostic counters */
cd->watchdog_count = 0;
cd->watchdog_irq_stuck_count = 0;
cd->watchdog_failed_access_count = 0;
cd->wd_xres_count = 0;
cd->irq_count = 0;
cd->bl_retry_packet_count = 0;
cd->pip2_crc_error_count = 0;
cd->bus_transmit_error_count = 0;
#endif
return ret;
}
static DEVICE_ATTR(ttdl_status, 0444, pt_ttdl_status_show, NULL);
/*******************************************************************************
* FUNCTION: pt_pip2_enter_bl_show
*
* SUMMARY: Show method for the pip2_enter_bl sysfs node that will force
* the DUT into the BL and show the success or failure of entering the BL
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_pip2_enter_bl_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
ssize_t ret = 0;
int rc = 0;
int result = 0;
u8 mode = PT_MODE_UNKNOWN;
struct pt_core_data *cd = dev_get_drvdata(dev);
/* Turn off the TTDL WD before enter bootloader */
pt_stop_wd_timer(cd);
/* Ensure NO enumeration work is queued or will be queued */
cancel_work_sync(&cd->enum_work);
mutex_lock(&cd->system_lock);
cd->bridge_mode = true;
mutex_unlock(&cd->system_lock);
/* set mode to operational to avoid any extra PIP traffic */
rc = _pt_request_pip2_enter_bl(dev, &mode, &result);
switch (result) {
case PT_ENTER_BL_PASS:
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE,
"Status: %d\nEntered BL\n", PT_ENTER_BL_PASS);
break;
case PT_ENTER_BL_ERROR:
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: %d\n%s\n",
rc,
" Unknown Error");
break;
case PT_ENTER_BL_RESET_FAIL:
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: %d\n%s\n",
rc,
" Soft Reset Failed");
break;
case PT_ENTER_BL_HID_START_BL_FAIL:
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: %d\n%s\n",
rc,
" PIP Start BL Cmd Failed");
break;
case PT_ENTER_BL_CONFIRM_FAIL:
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: %d\n%s\n",
rc,
" Error confirming DUT entered BL");
break;
default:
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: %d\n%s\n",
rc, " Unknown Error");
break;
};
/* Allow enumeration work to be queued again */
cd->bridge_mode = false;
return ret;
}
static DEVICE_ATTR(pip2_enter_bl, 0444, pt_pip2_enter_bl_show, NULL);
/*******************************************************************************
* FUNCTION: pt_pip2_exit_bl_show
*
* SUMMARY: Show method for the pip2_exit_bl sysfs node that will attempt to
* launch the APP and put the DUT Application mode
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_pip2_exit_bl_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret = 0;
int rc = 0;
u8 status_str[PT_STATUS_STR_LEN];
rc = pt_pip2_exit_bl_(cd, status_str, PT_STATUS_STR_LEN);
/*
* Perform enum if startup_status doesn't reach to
* STARTUP_STATUS_FW_OUT_OF_BOOT.
*/
if (!rc && (!(cd->startup_status & STARTUP_STATUS_FW_OUT_OF_BOOT))) {
rc = pt_enum_with_dut(cd, false, &cd->startup_status);
if (!(cd->startup_status & STARTUP_STATUS_FW_OUT_OF_BOOT)) {
strlcpy(status_str,
"Already in APP mode - FW stuck in Boot mode", sizeof(status_str));
}
}
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: %d\n%s\n",
rc, status_str);
return ret;
}
static DEVICE_ATTR(pip2_exit_bl, 0444, pt_pip2_exit_bl_show, NULL);
#endif
#ifdef EASYWAKE_TSG6
/*******************************************************************************
* FUNCTION: pt_easy_wakeup_gesture_show
*
* SUMMARY: Show method for the easy_wakeup_gesture sysfs node that will show
* current easy wakeup gesture
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_easy_wakeup_gesture_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret;
mutex_lock(&cd->system_lock);
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "0x%02X\n",
cd->easy_wakeup_gesture);
mutex_unlock(&cd->system_lock);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_easy_wakeup_gesture_store
*
* SUMMARY: The store method for the easy_wakeup_gesture sysfs node that
* allows the wake gesture to be set to a custom value.
*
* RETURN: Size of passed in buffer is success
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to buffer that hold the command parameters
* size - size of buf
******************************************************************************/
static ssize_t pt_easy_wakeup_gesture_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u32 input_data[2];
int length;
int rc = 0;
/* Maximum input of one value */
length = _pt_ic_parse_input(dev, buf, size, input_data,
ARRAY_SIZE(input_data));
if (length != 1) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
}
pt_debug(dev, DL_INFO, "%s: features.easywake = 0x%02X\n",
__func__, cd->features.easywake);
if (!cd->features.easywake || input_data[0] > 0xFF) {
rc = -EINVAL;
goto exit;
}
pm_runtime_get_sync(dev);
mutex_lock(&cd->system_lock);
if (cd->sysinfo.ready && IS_PIP_VER_GE(&cd->sysinfo, 1, 2)) {
cd->easy_wakeup_gesture = (u8)input_data[0];
pt_debug(dev, DL_INFO,
"%s: Updated easy_wakeup_gesture = 0x%02X\n",
__func__, cd->easy_wakeup_gesture);
} else
rc = -ENODEV;
mutex_unlock(&cd->system_lock);
pm_runtime_put(dev);
exit:
if (rc)
return rc;
return size;
}
/*******************************************************************************
* FUNCTION: pt_easy_wakeup_gesture_id_show
*
* SUMMARY: Show method for the easy_wakeup_gesture_id sysfs node that will
* show the TSG6 easywake gesture ID
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_easy_wakeup_gesture_id_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret;
mutex_lock(&cd->system_lock);
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: 0\n0x%02X\n",
cd->gesture_id);
mutex_unlock(&cd->system_lock);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_easy_wakeup_gesture_data_show
*
* SUMMARY: Show method for the easy_wakeup_gesture_data sysfs node that will
* show the TSG6 easywake gesture data in the following format:
* x1(LSB),x1(MSB), y1(LSB),y1(MSB), x2(LSB),x2(MSB), y2(LSB),y2(MSB),...
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_easy_wakeup_gesture_data_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret = 0;
int i;
mutex_lock(&cd->system_lock);
ret += scnprintf(buf + ret, PT_MAX_PRBUF_SIZE - ret, "Status: %d\n", 0);
for (i = 0; i < cd->gesture_data_length; i++)
ret += scnprintf(buf + ret, PT_MAX_PRBUF_SIZE - ret,
"0x%02X\n", cd->gesture_data[i]);
ret += scnprintf(buf + ret, PT_MAX_PRBUF_SIZE - ret,
"(%d bytes)\n", cd->gesture_data_length);
mutex_unlock(&cd->system_lock);
return ret;
}
#endif /* EASYWAKE_TSG6 */
#ifdef TTDL_DIAGNOSTICS
/*******************************************************************************
* FUNCTION: pt_err_gpio_show
*
* SUMMARY: Show method for the err_gpio sysfs node that will show if
* setting up the gpio was successful
*
* RETURN: Char buffer with printed GPIO creation state
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_err_gpio_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
return scnprintf(buf, strlen(buf), "Status: 0\n"
"Err GPIO (%d) : %s\n"
"Err GPIO trig type: %d\n",
cd->err_gpio,
(cd->err_gpio ? (gpio_get_value(cd->err_gpio) ?
"HIGH" : "low") : "not defined"),
cd->err_gpio_type);
}
/*******************************************************************************
* FUNCTION: pt_err_gpio_store
*
* SUMMARY: The store method for the err_gpio sysfs node that allows any
* available host GPIO to be used to trigger when TTDL detects a PIP
* command/response timeout.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to buffer that hold the command parameters
* size - size of buf
******************************************************************************/
static ssize_t pt_err_gpio_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
unsigned long gpio;
int rc = 0;
u32 input_data[3];
int length;
u8 err_type;
input_data[0] = 0;
input_data[1] = 0;
/* Maximmum input is two elements */
length = _pt_ic_parse_input(dev, buf, size,
input_data, ARRAY_SIZE(input_data));
if (length < 1 || length > 2) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
}
gpio = input_data[0];
err_type = (u8)input_data[1];
if (err_type < 0 || err_type > PT_ERR_GPIO_MAX_TYPE) {
rc = -EINVAL;
goto exit;
}
mutex_lock(&cd->system_lock);
gpio_free(gpio);
rc = gpio_request(gpio, NULL);
if (rc) {
pt_debug(dev, DL_ERROR, "error requesting gpio %lu\n", gpio);
rc = -ENODEV;
} else {
cd->err_gpio = gpio;
cd->err_gpio_type = err_type;
gpio_direction_output(gpio, 0);
}
mutex_unlock(&cd->system_lock);
exit:
if (rc)
return rc;
return size;
}
static DEVICE_ATTR(err_gpio, 0644, pt_err_gpio_show,
pt_err_gpio_store);
/*******************************************************************************
* FUNCTION: pt_drv_irq_show
*
* SUMMARY: Show method for the drv_irq sysfs node that will show if the
* TTDL interrupt is enabled/disabled
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_drv_irq_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret = 0;
mutex_lock(&cd->system_lock);
ret += scnprintf(buf, PT_MAX_PRBUF_SIZE, "Status: %d\n", 0);
if (cd->irq_enabled)
ret += scnprintf(buf + ret, PT_MAX_PRBUF_SIZE - ret,
"Driver interrupt: ENABLED\n");
else
ret += scnprintf(buf + ret, PT_MAX_PRBUF_SIZE - ret,
"Driver interrupt: DISABLED\n");
mutex_unlock(&cd->system_lock);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_drv_irq_store
*
* SUMMARY: The store method for the drv_irq sysfs node that allows the TTDL
* IRQ to be enabled/disabled.
*
* RETURN: Size of passed in buffer
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to buffer that hold the command parameters
* size - size of buf
******************************************************************************/
static ssize_t pt_drv_irq_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u32 input_data[2];
int length;
int rc = 0;
/* Maximum input of one value */
length = _pt_ic_parse_input(dev, buf, size, input_data,
ARRAY_SIZE(input_data));
if (length != 1) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
}
mutex_lock(&cd->system_lock);
switch (input_data[0]) {
case 0:
if (cd->irq_enabled) {
cd->irq_enabled = false;
/* Disable IRQ has no return value to check */
disable_irq_nosync(cd->irq);
pt_debug(dev, DL_INFO,
"%s: Driver IRQ now disabled\n",
__func__);
} else
pt_debug(dev, DL_INFO,
"%s: Driver IRQ already disabled\n",
__func__);
break;
case 1:
if (cd->irq_enabled == false) {
cd->irq_enabled = true;
enable_irq(cd->irq);
pt_debug(dev, DL_INFO,
"%s: Driver IRQ now enabled\n",
__func__);
} else
pt_debug(dev, DL_INFO,
"%s: Driver IRQ already enabled\n",
__func__);
break;
default:
rc = -EINVAL;
pt_debug(dev, DL_ERROR, "%s: Invalid value\n", __func__);
}
mutex_unlock(&(cd->system_lock));
exit:
if (rc)
return rc;
return size;
}
/*******************************************************************************
* FUNCTION: pt_pip2_bin_hdr_show
*
* SUMMARY: Show method for the pip2_bin_hdr sysfs node that will read
* the bin file header from flash and show each field
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_pip2_bin_hdr_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
ssize_t ret = 0;
struct pt_bin_file_hdr hdr = {0};
int rc;
rc = _pt_request_pip2_bin_hdr(dev, &hdr);
ret = scnprintf(buf, strlen(buf),
"%s: %d\n"
"%s: %d\n"
"%s: 0x%04X\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: 0x%08X\n"
"%s: 0x%04X\n"
"%s: 0x%04X\n"
"%s: %d\n"
"%s: %d\n",
"Status", rc,
"Header Length ", hdr.length,
"TTPID ", hdr.ttpid,
"FW Major Ver ", hdr.fw_major,
"FW Minor Ver ", hdr.fw_minor,
"FW Rev Control ", hdr.fw_rev_ctrl,
"FW CRC ", hdr.fw_crc,
"Silicon Rev ", hdr.si_rev,
"Silicon ID ", hdr.si_id,
"Config Ver ", hdr.config_ver,
"HEX File Size ", hdr.hex_file_size
);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_platform_data_show
*
* SUMMARY: Show method for the platform_data sysfs node that will show the
* active platform data including: GPIOs, Vendor and Product IDs,
* Virtual Key coordinates, Core/MT/Loader flags, Level trigger delay,
* HID registers, and Easy wake gesture
*
* RETURN: Size of printed data
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_platform_data_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_platform_data *pdata = dev_get_platdata(dev);
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret;
ret = scnprintf(buf, strlen(buf),
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %s\n"
"%s: %s\n"
"%s: %d\n",
"Status", 0,
"Interrupt GPIO ", pdata->core_pdata->irq_gpio,
"Interrupt GPIO Value ",
pdata->core_pdata->irq_gpio ?
gpio_get_value(pdata->core_pdata->irq_gpio) : 0,
"Reset GPIO ", pdata->core_pdata->rst_gpio,
"Reset GPIO Value ",
pdata->core_pdata->rst_gpio ?
gpio_get_value(pdata->core_pdata->rst_gpio) : 0,
"DDI Reset GPIO ", pdata->core_pdata->ddi_rst_gpio,
"DDI Reset GPIO Value ",
pdata->core_pdata->ddi_rst_gpio ?
gpio_get_value(pdata->core_pdata->ddi_rst_gpio) : 0,
"VDDI GPIO ", pdata->core_pdata->vddi_gpio,
"VDDI GPIO Value ",
pdata->core_pdata->vddi_gpio ?
gpio_get_value(pdata->core_pdata->vddi_gpio) : 0,
"VCC GPIO ", pdata->core_pdata->vcc_gpio,
"VCC GPIO Value ",
pdata->core_pdata->vcc_gpio ?
gpio_get_value(pdata->core_pdata->vcc_gpio) : 0,
"AVDD GPIO ", pdata->core_pdata->avdd_gpio,
"AVDD GPIO Value ",
pdata->core_pdata->avdd_gpio ?
gpio_get_value(pdata->core_pdata->avdd_gpio) : 0,
"AVEE GPIO ", pdata->core_pdata->avee_gpio,
"AVEE GPIO Value ",
pdata->core_pdata->avee_gpio ?
gpio_get_value(pdata->core_pdata->avee_gpio) : 0,
"Vendor ID ", pdata->core_pdata->vendor_id,
"Product ID ", pdata->core_pdata->product_id,
"Vkeys x ", pdata->mt_pdata->vkeys_x,
"Vkeys y ", pdata->mt_pdata->vkeys_y,
"Core data flags ", pdata->core_pdata->flags,
"MT data flags ", pdata->mt_pdata->flags,
"Loader data flags ", pdata->loader_pdata->flags,
"Level trigger delay (us) ",
pdata->core_pdata->level_irq_udelay,
"HID Descriptor Register ",
pdata->core_pdata->hid_desc_register,
"HID Output Register ",
cd->hid_desc.output_register,
"HID Command Register ",
cd->hid_desc.command_register,
"Easy wakeup gesture ",
pdata->core_pdata->easy_wakeup_gesture,
"Config DUT generation ",
pdata->core_pdata->config_dut_generation ?
(pdata->core_pdata->config_dut_generation ==
CONFIG_DUT_PIP2_CAPABLE ?
"PT TC/TT" : "Gen5/6") : "Auto",
"Watchdog Force Stop ",
pdata->core_pdata->watchdog_force_stop ?
"True" : "False",
"Panel ID Support ",
pdata->core_pdata->panel_id_support);
return ret;
}
#define PT_ERR_STR_SIZE 64
/*******************************************************************************
* FUNCTION: pt_bist_bus_test
*
* SUMMARY: Tests the connectivity of the active bus pins:
* I2C - SDA and SCL
* SPI - MOSI, MISO, CLK
*
* Disable TTDL interrupts, send a PIP cmd and then manually read the
* bus. If any data is read we know the I2C/SPI pins are connected
*
* RETURN:
* 0 = Success
* !0 = Failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *net_toggled - pointer to where to store if bus toggled
* *err_str - pointer to error string buffer
******************************************************************************/
static int pt_bist_bus_test(struct device *dev, u8 *net_toggled, u8 *err_str)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u8 ver_cmd[8] = {0x01, 0x01, 0x06, 0x00, 0x0E, 0x07, 0xF0, 0xB1};
u8 *read_buf = NULL;
int bytes_read = 0;
int rc = 0;
read_buf = kzalloc(PT_MAX_PIP1_MSG_SIZE, GFP_KERNEL);
if (read_buf == NULL) {
rc = -ENOMEM;
goto exit;
}
bytes_read = pt_flush_bus(cd, PT_FLUSH_BUS_BASED_ON_LEN, NULL);
pt_debug(dev, DL_INFO, "%s: TTDL Core Suspend\n", __func__);
disable_irq(cd->irq);
mutex_lock(&cd->system_lock);
cd->irq_disabled = true;
mutex_unlock(&cd->system_lock);
/*
* Sleep >4ms to allow any pending TTDL IRQ to finish. Without this
* the disable_irq_nosync() could cause the IRQ to get stuck asserted
*/
usleep_range(5000, 6000);
pt_debug(cd->dev, DL_INFO, ">>> %s: Write Buffer Size[%d] VERSION\n",
__func__, (int)sizeof(ver_cmd));
pt_pr_buf(cd->dev, DL_DEBUG, ver_cmd, (int)sizeof(ver_cmd),
">>> User CMD");
rc = pt_adap_write_read_specific(cd, sizeof(ver_cmd), ver_cmd, NULL);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: BUS Test - Failed to send VER cmd\n", __func__);
*net_toggled = 0;
strlcpy(err_str,
"- Write failed, bus open or shorted or DUT in reset", PT_ERR_STR_SIZE);
goto exit_enable_irq;
}
usleep_range(4000, 5000);
bytes_read = pt_flush_bus(cd, PT_FLUSH_BUS_BASED_ON_LEN, read_buf);
pt_debug(dev, DL_INFO, "%s: BUS Test - %d bytes forced read\n",
__func__, bytes_read);
if (bytes_read == 0) {
*net_toggled = 0;
pt_debug(dev, DL_INFO, "%s: BUS Read Failed, 0 bytes read\n",
__func__);
strlcpy(err_str,
"- Bus open, shorted or DUT in reset", PT_ERR_STR_SIZE);
rc = -EIO;
goto exit_enable_irq;
} else {
if (cd->bus_ops->bustype == BUS_I2C)
*net_toggled = 1;
else {
if ((bytes_read > 3) &&
(read_buf[3] & PIP2_CMD_COMMAND_ID_MASK) ==
PIP2_CMD_ID_VERSION)
*net_toggled = 1;
else {
*net_toggled = 0;
pt_debug(dev, DL_INFO,
"%s: BUS Read Failed, %d bytes read\n",
__func__, bytes_read);
strlcpy(err_str,
"- Bus open, shorted or DUT in reset", PT_ERR_STR_SIZE);
}
}
}
exit_enable_irq:
enable_irq(cd->irq);
usleep_range(5000, 6000);
mutex_lock(&cd->system_lock);
cd->irq_disabled = false;
mutex_unlock(&cd->system_lock);
pt_debug(dev, DL_INFO, "%s: TTDL Core Resumed\n", __func__);
exit:
kfree(read_buf);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_bist_irq_test
*
* SUMMARY: Tests the connectivity of the IRQ net
*
* This test will ensure there is a good connection between the host
* and the DUT on the irq pin. First determine if the IRQ is stuck
* asserted and if so keep reading messages off of the bus until
* it de-asserts. Possible outcomes:
* - IRQ was already de-asserted: Send a PIP command and if an
* interrupt is generated the test passes.
* - IRQ was asserted: Reading off the bus de-assertes the IRQ,
* test passes.
* - IRQ stays asserted: After reading the bus multiple times
* the IRQ stays asserted. Likely open or shorted to GND
*
* RETURN:
* 0 = Success
* !0 = Failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *bus_toggled - pointer to where to store if bus toggled
* *irq_toggled - pointer to where to store if IRQ toggled
* *xres_toggled - pointer to where to store if XRES toggled
* *err_str - pointer to error string buffer
******************************************************************************/
static int pt_bist_irq_test(struct device *dev,
u8 *bus_toggled, u8 *irq_toggled, u8 *xres_toggled, u8 *err_str)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u8 *read_buf = NULL;
u8 mode = PT_MODE_UNKNOWN;
u16 actual_read_len;
int bytes_read = 0;
int count = 0;
int rc = 0;
read_buf = kzalloc(PT_MAX_PIP1_MSG_SIZE, GFP_KERNEL);
if (read_buf == NULL) {
rc = -ENOMEM;
goto exit;
}
/* Clear IRQ triggered count, and re-evaluate at the end of test */
cd->irq_count = 0;
/*
* Check if IRQ is stuck asserted, if so try a non forced flush of
* the bus based on the 2 byte initial length read. Try up to 5x.
*/
while (pt_check_irq_asserted(cd) && count < 5) {
count++;
bytes_read += pt_flush_bus(cd, PT_FLUSH_BUS_BASED_ON_LEN, NULL);
}
if (count > 1 && count < 5 && bytes_read > 0) {
/*
* IRQ was stuck but data was successfully read from the
* bus releasing the IRQ line.
*/
pt_debug(dev, DL_INFO, "%s: count=%d bytes_read=%d\n",
__func__, count, bytes_read);
*bus_toggled = 1;
*irq_toggled = 1;
goto exit;
}
if (count == 5 && bytes_read == 0) {
/*
* Looped 5x and read nothing off the bus yet the IRQ is still
* asserted. Possible conditions:
* - IRQ open circuit
* - IRQ shorted to GND
* - I2C/SPI bus is disconnected
* - FW holding the pin low
* Try entering the BL to see if communication works there.
*/
mode = PT_MODE_IGNORE;
rc = _pt_request_pip2_enter_bl(dev, &mode, NULL);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s Failed to enter BL\n", __func__);
strlcpy(err_str,
"- likely shorted to GND or FW holding it.", PT_ERR_STR_SIZE);
*irq_toggled = 0;
goto exit;
}
/*
* If original mode was operational and we successfully
* entered the BL, then the XRES net must have toggled
*/
if (mode == PT_MODE_OPERATIONAL)
*xres_toggled = 1;
rc = _pt_request_pip2_send_cmd(dev, PT_CORE_CMD_PROTECTED,
PIP2_CMD_ID_VERSION, NULL, 0, read_buf,
&actual_read_len);
if (rc) {
/*
* Could not communicate to DUT in BL mode. Save the
* error string, slim chance but the XRES test below may
* show the IRQ is actually working.
*/
strlcpy(err_str, "- likely shorted to GND.", PT_ERR_STR_SIZE);
pt_debug(dev, DL_ERROR,
"%s: %s, count=%d bytes_read=%d\n",
__func__, err_str, count, bytes_read);
*irq_toggled = 0;
rc = pt_pip2_exit_bl_(cd, NULL, 0);
goto exit;
} else {
*bus_toggled = 1;
*irq_toggled = 1;
goto exit;
}
}
if (pt_check_irq_asserted(cd)) {
strlcpy(err_str, "- likely shorted to GND", PT_ERR_STR_SIZE);
rc = -EIO;
*irq_toggled = 0;
goto exit;
}
/* Try sending a PIP command to see if we get a response */
rc = _pt_request_pip2_send_cmd(dev, PT_CORE_CMD_PROTECTED,
PIP2_CMD_ID_VERSION, NULL, 0, read_buf, &actual_read_len);
if (rc) {
/*
* Potential IRQ issue, no communication in App mode, attempt
* the same command in the BL
*/
mode = PT_MODE_IGNORE;
rc = _pt_request_pip2_enter_bl(dev, &mode, NULL);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s Failed to enter BL\n", __func__);
*irq_toggled = 0;
strlcpy(err_str, "- likely open or shorted to VDDI.", PT_ERR_STR_SIZE);
goto exit;
}
/*
* If original mode was operational and we successfully
* entered the BL, this will be useful info for the tp_xres
* test below.
*/
if (mode == PT_MODE_OPERATIONAL)
*xres_toggled = 1;
rc = _pt_request_pip2_send_cmd(dev, PT_CORE_CMD_PROTECTED,
PIP2_CMD_ID_VERSION, NULL, 0, read_buf,
&actual_read_len);
if (rc) {
/*
* Could not communicate in FW mode or BL mode. Save the
* error string, slim chance but the XRES test below may
* show the IRQ is actually working.
*/
strlcpy(err_str, "- likely open or shorted to VDDI.", PT_ERR_STR_SIZE);
pt_debug(dev, DL_ERROR,
"%s: request_active_pip_prot failed\n",
__func__);
*irq_toggled = 0;
goto exit;
}
}
if (cd->irq_count > 0) {
pt_debug(dev, DL_INFO, "%s: irq_count=%d\n", __func__,
cd->irq_count);
*bus_toggled = 1;
*irq_toggled = 1;
goto exit;
}
exit:
kfree(read_buf);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_bist_xres_test
*
* SUMMARY: Tests the connectivity of the TP_XRES net
*
* This test will ensure there is a good connection between the host
* and the DUT on the tp_xres pin. The pin will be toggled to
* generate a TP reset which will cause the DUT to output a reset
* sentinel. If the reset sentinel is seen the test passes. If it is
* not seen the test will attempt to send a soft reset to simply gain
* some additional information on the failure:
* - soft reset fails to send: XRES and IRQ likely open
* - soft reset passes: XRES likely open or stuck de-asserted
* - soft reset fails: XRES likely stuck asserted
*
* RETURN:
* 0 = Success
* !0 = Failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *bus_toggled - pointer to where to store if bus toggled
* *irq_toggled - pointer to where to store if IRQ toggled
* *xres_toggled - pointer to where to store if XRES toggled
* *err_str - pointer to error string buffer
******************************************************************************/
static int pt_bist_xres_test(struct device *dev,
u8 *bus_toggled, u8 *irq_toggled, u8 *xres_toggled, u8 *err_str)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_platform_data *pdata = dev_get_platdata(dev);
u8 *read_buf = NULL;
u8 mode = PT_MODE_UNKNOWN;
int rc = 0;
int t = 0;
int timeout = 300;
read_buf = kzalloc(PT_MAX_PIP1_MSG_SIZE, GFP_KERNEL);
if (read_buf == NULL) {
rc = -ENOMEM;
goto exit;
}
/* Clear the startup bit mask, reset and enum will re-populate it */
cd->startup_status = STARTUP_STATUS_START;
pt_debug(dev, DL_DEBUG, "%s: Startup Status Reset\n", __func__);
if ((!pdata->core_pdata->rst_gpio) || (!pdata->core_pdata->xres)) {
strlcpy(err_str, "- Net not configured or available", PT_ERR_STR_SIZE);
rc = -ENODEV;
goto exit;
}
/* Ensure we have nothing pending on active bus */
pt_flush_bus_if_irq_asserted(cd, PT_FLUSH_BUS_BASED_ON_LEN);
/* Perform a hard XRES toggle and wait for reset sentinel */
mutex_lock(&cd->system_lock);
cd->hid_reset_cmd_state = 1;
mutex_unlock(&cd->system_lock);
pt_debug(dev, DL_INFO, "%s: Perform a hard reset\n", __func__);
rc = pt_hw_hard_reset(cd);
/* Set timeout to 1s for the flashless case where a BL could be done */
if (cd->flashless_dut)
timeout = 1000;
/*
* To avoid the case that next PIP command can be confused by BL/FW
* sentinel's "wakeup" event, chekcing hid_reset_cmd_state which is
* followed by "wakeup event" function can lower the failure rate.
*/
t = wait_event_timeout(cd->wait_q,
((cd->startup_status != STARTUP_STATUS_START)
&& (cd->hid_reset_cmd_state == 0)),
msecs_to_jiffies(timeout));
if (IS_TMO(t)) {
pt_debug(cd->dev, DL_ERROR,
"%s: TMO waiting for sentinel\n", __func__);
*xres_toggled = 0;
strlcpy(err_str, "- likely open. (No Reset Sentinel)", PT_ERR_STR_SIZE);
/*
* Possibly bad FW, Try entering BL and wait for reset sentinel.
* To enter the BL we need to generate an XRES so first try to
* launch the applicaiton
*/
if (cd->mode == PT_MODE_BOOTLOADER)
pt_pip2_launch_app(dev, PT_CORE_CMD_PROTECTED);
pt_debug(dev, DL_INFO, "%s: Enter BL with a hard reset\n",
__func__);
mode = PT_MODE_IGNORE;
rc = _pt_request_pip2_enter_bl(dev, &mode, NULL);
if (rc) {
pt_debug(dev, DL_ERROR, "%s Failed to enter BL\n",
__func__);
*xres_toggled = 0;
strlcpy(err_str, "- likely open or shorted to VDDI.", PT_ERR_STR_SIZE);
goto exit;
} else {
/* Wait for the BL sentinel */
t = wait_event_timeout(cd->wait_q,
(cd->startup_status != STARTUP_STATUS_START),
msecs_to_jiffies(500));
if (IS_TMO(t)) {
pt_debug(cd->dev, DL_ERROR,
"%s: TMO waiting for BL sentinel\n",
__func__);
*xres_toggled = 0;
strlcpy(err_str,
"- likely open or shorted to VDDI.", PT_ERR_STR_SIZE);
rc = -ETIME;
goto exit;
}
}
}
mutex_lock(&cd->system_lock);
cd->hid_reset_cmd_state = 0;
mutex_unlock(&cd->system_lock);
/* Look for BL or FW reset sentinels */
if (!rc && ((cd->startup_status & STARTUP_STATUS_BL_RESET_SENTINEL) ||
(cd->startup_status & STARTUP_STATUS_FW_RESET_SENTINEL))) {
pt_debug(dev, DL_INFO, "%s: hard XRES pass\n", __func__);
/* If a sentinel was seen, all nets are working */
*xres_toggled = 1;
*irq_toggled = 1;
/*
* For SPI test, bus read result can be confused as FW sentinel
* if MISO(slave) is connected to MISO(host).
*/
if (cd->bus_ops->bustype == BUS_I2C)
*bus_toggled = 1;
} else {
/*
* Hard reset failed, however some additional information
* could be determined. Try a soft reset to see if DUT resets
* with the possible outcomes:
* - if it resets the line is not stuck asserted
* - if it does not reset the line could be stuck asserted
*/
*xres_toggled = 0;
rc = pt_hw_soft_reset(cd, PT_CORE_CMD_PROTECTED);
msleep(30);
pt_debug(dev, DL_INFO, "%s: TP_XRES BIST soft reset rc=%d",
__func__, rc);
if (rc) {
strlcpy(err_str, "- likely open.", PT_ERR_STR_SIZE);
pt_debug(dev, DL_ERROR,
"%s: Hard reset failed, soft reset failed %s\n",
__func__, err_str);
goto exit;
}
if (cd->startup_status & STARTUP_STATUS_BL_RESET_SENTINEL ||
cd->startup_status & STARTUP_STATUS_FW_RESET_SENTINEL) {
strlcpy(err_str,
"- likely open or stuck high, soft reset OK", PT_ERR_STR_SIZE);
pt_debug(dev, DL_ERROR,
"%s: Hard reset failed, soft reset passed-%s\n",
__func__, err_str);
} else if (cd->startup_status == 0) {
strlcpy(err_str, "- likely stuck high.", PT_ERR_STR_SIZE);
pt_debug(dev, DL_ERROR,
"%s: Hard reset failed, soft reset failed-%s\n",
__func__, err_str);
} else {
strlcpy(err_str, "- open or stuck.", PT_ERR_STR_SIZE);
pt_debug(dev, DL_ERROR,
"%s: Hard and Soft reset failed - %s\n",
__func__, err_str);
}
}
exit:
kfree(read_buf);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_bist_slave_irq_test
*
* SUMMARY: Tests the connectivity of the Master/Slave IRQ net
*
* This test will ensure there is a good IRQ connection between the master
* DUT and the slave DUT(s). After power up the STATUS command is sent
* and the 'Slave Detect' bits are verified to ensure the master DUT
* saw each slave trigger the IRQ with it's reset sentinel.
*
* RETURN:
* 0 = Success
* !0 = Failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *slave_irq_toggled - pointer to where to store if slave IRQ toggled
* *slave_bus_toggled - pointer to where to store if slave Bus toggled
* *err_str - pointer to error string buffer
* *slave_detect - pointer to slave detect buffer
* *boot_err - pointer to boot_err buffer
******************************************************************************/
static int pt_bist_slave_irq_test(struct device *dev,
u8 *slave_irq_toggled, u8 *slave_bus_toggled, u8 *err_str,
u8 *slave_detect, u8 *boot_err)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u8 mode = PT_MODE_UNKNOWN;
u8 status;
u8 boot;
u8 read_buf[12];
u8 detected = 0;
u8 last_err = -1;
u16 actual_read_len;
int result = 0;
int rc = 0;
/*
* Ensure DUT is in the BL where the STATUS cmd will report the slave
* detect bits. If the DUT was in FW, entering the BL will cause an
* XRES signal which will inadvertently test the XRES net as well
*/
rc = _pt_request_pip2_enter_bl(dev, &mode, &result);
if (rc) {
pt_debug(cd->dev, DL_ERROR, "%s: Error entering BL rc=%d\n",
__func__, rc);
strlcpy(err_str, "- State could not be determined.", PT_ERR_STR_SIZE);
goto exit;
}
/* Use the STATUS command to retrieve the slave detect bit(s) */
rc = _pt_request_pip2_send_cmd(cd->dev, PT_CORE_CMD_UNPROTECTED,
PIP2_CMD_ID_STATUS, NULL, 0, read_buf,
&actual_read_len);
if (!rc) {
pt_pr_buf(cd->dev, DL_INFO, read_buf, actual_read_len,
"PIP2 STATUS");
status = read_buf[PIP2_RESP_STATUS_OFFSET];
boot = read_buf[PIP2_RESP_BODY_OFFSET] & 0x01;
/* Slave detect is only valid if status ok and in boot exec */
if (status == PIP2_RSP_ERR_NONE &&
boot == PIP2_STATUS_BOOT_EXEC) {
detected = read_buf[PIP2_RESP_BODY_OFFSET + 2] &
SLAVE_DETECT_MASK;
} else {
strlcpy(err_str, "- State could not be determined", PT_ERR_STR_SIZE);
rc = -EPERM;
}
} else {
pt_debug(cd->dev, DL_ERROR, "%s: STATUS cmd failure\n",
__func__);
strlcpy(err_str, "- State could not be determined.", PT_ERR_STR_SIZE);
goto exit;
}
/*
* Retrieve boot error regardless of the state of the slave detect
* bit because the IRQ could have been stuck high or low.
*/
rc = _pt_request_pip2_send_cmd(cd->dev, PT_CORE_CMD_UNPROTECTED,
PIP2_CMD_ID_GET_LAST_ERRNO, NULL, 0,
read_buf, &actual_read_len);
if (!rc) {
pt_pr_buf(cd->dev, DL_INFO, read_buf, actual_read_len,
"PIP2 GET_LAST_ERRNO");
status = read_buf[PIP2_RESP_STATUS_OFFSET];
last_err = read_buf[PIP2_RESP_BODY_OFFSET];
if (last_err) {
pt_debug(cd->dev, DL_ERROR,
"%s: Master Boot Last Err = 0x%02X\n",
__func__, last_err);
}
} else {
pt_debug(cd->dev, DL_ERROR,
"%s: GET_LAST_ERRNO cmd failure\n", __func__);
strlcpy(err_str, "- stuck, likely shorted to GND.", PT_ERR_STR_SIZE);
}
exit:
pt_debug(cd->dev, DL_INFO,
"%s: rc=%d detected=0x%02X boot_err=0x%02X\n",
__func__, rc, detected, last_err);
if (err_str && last_err) {
if (detected)
scnprintf(err_str, PT_ERR_STR_SIZE, "%s 0x%02X",
"- Likely stuck low. Boot Error:",
last_err);
else
scnprintf(err_str, PT_ERR_STR_SIZE, "%s 0x%02X",
"- Likely stuck high. Boot Error:",
last_err);
}
/* Ignore an invalid image error as BIST doesn't need valid FW */
if (last_err == PIP2_RSP_ERR_INVALID_IMAGE)
last_err = PIP2_RSP_ERR_NONE;
if (slave_irq_toggled)
*slave_irq_toggled = (detected && !last_err) ? true : false;
if (slave_bus_toggled) {
/* Leave as UNTEST if slave not detected */
if (detected)
*slave_bus_toggled = !last_err ? true : false;
}
if (slave_detect)
*slave_detect = detected;
if (boot_err)
*boot_err = last_err;
if (slave_irq_toggled && slave_bus_toggled)
pt_debug(cd->dev, DL_INFO, "%s: %s=0x%02X, %s=0x%02X, %s=0x%02X\n",
__func__,
"Detected", detected,
"slave_irq_toggled", *slave_irq_toggled,
"slave_bus_toggled", *slave_bus_toggled);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_bist_slave_xres_test
*
* SUMMARY: Tests the connectivity of the Master/Slave TP_XRES net
*
* This test will ensure there is a good TP_XRES connection between the
* master DUT and the slave DUT(s). After toggling the XRES pin to the
* master, the STATUS command is sent and the 'Slave Detect' bits are
* verified to ensure the master DUT saw each slave trigger the IRQ with
* it's reset sentinel.
*
* RETURN:
* 0 = Success
* !0 = Failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *slave_irq_toggled - pointer to where to store if slave IRQ toggled
* *slave_bus_toggled - pointer to where to store if slave Bus toggled
* *slave_xres_toggled - pointer to where to store if slave XRES toggled
* *err_str - pointer to error string buffer
******************************************************************************/
static int pt_bist_slave_xres_test(struct device *dev,
u8 *slave_irq_toggled, u8 *slave_bus_toggled, u8 *slave_xres_toggled,
u8 *err_str)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u8 slave_detect = 0;
u8 boot_err = 0;
int rc = 0;
/* Force a reset to force the 'slave detect' bits to be re-acquired */
mutex_lock(&cd->system_lock);
cd->hid_reset_cmd_state = 1;
mutex_unlock(&cd->system_lock);
pt_debug(dev, DL_INFO, "%s: Perform a hard reset\n", __func__);
pt_hw_hard_reset(cd);
msleep(100);
rc = pt_bist_slave_irq_test(dev, slave_irq_toggled,
slave_bus_toggled, err_str, &slave_detect, &boot_err);
pt_debug(dev, DL_INFO, "%s: IRQ test rc = %d\n", __func__, rc);
if (!rc && *slave_irq_toggled == false) {
/*
* If the slave IRQ did not toggle, either the slave_detect
* bit was not set or we had a boot error. If the slave
* detect was not set the slave did not reset causing a boot
* error.
*/
if (!slave_detect)
strlcpy(err_str, "- likely open.", PT_ERR_STR_SIZE);
else
scnprintf(err_str, PT_ERR_STR_SIZE, "%s 0x%02X",
"- likely open or an IRQ issue. Boot Error:",
boot_err);
}
if (slave_xres_toggled) {
if (!rc)
*slave_xres_toggled = *slave_irq_toggled ? true : false;
else
*slave_xres_toggled = false;
}
return rc;
}
/*******************************************************************************
* FUNCTION: pt_bist_slave_bus_test
*
* SUMMARY: Tests the connectivity of the Master/Slave SPI bus net
*
* This test will ensure a good SPI bus connection between the
* master DUT and the slave DUT(s). This bus connection is ensured by
* opening file 0 (SRAM loader). If there is a slave and the open fails
* then there is a master/slave communication issue. Opening file 0 on
* the master will open it on the slave as well if the slave was detected.
*
* RETURN:
* 0 = Success
* !0 = Failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *slave_irq_toggled - pointer to where to store if slave IRQ toggled
* *slave_bus_toggled - pointer to where to store if slave Bus toggled
* *err_str - pointer to error string buffer
******************************************************************************/
static int pt_bist_slave_bus_test(struct device *dev,
u8 *slave_irq_toggled, u8 *slave_bus_toggled, u8 *err_str)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u8 mode = PT_MODE_UNKNOWN;
u8 bus_toggled = false;
u8 file_handle;
int result = 0;
int rc = 0;
rc = _pt_request_pip2_enter_bl(dev, &mode, &result);
if (rc) {
pt_debug(cd->dev, DL_ERROR, "%s: Error entering BL rc=%d\n",
__func__, rc);
strlcpy(err_str, "- State could not be determined.", PT_ERR_STR_SIZE);
goto exit;
}
pt_debug(dev, DL_INFO, "%s Attempt open file 0\n", __func__);
file_handle = _pt_pip2_file_open(dev, PIP2_RAM_FILE);
if (file_handle != PIP2_RAM_FILE) {
rc = -ENOENT;
bus_toggled = false;
pt_debug(dev, DL_ERROR,
"%s Failed to open bin file\n", __func__);
strlcpy(err_str, "- Bus open, shorted or DUT in reset", PT_ERR_STR_SIZE);
goto exit;
} else {
bus_toggled = true;
if (file_handle != _pt_pip2_file_close(dev, file_handle)) {
pt_debug(dev, DL_ERROR,
"%s: File Close failed, file_handle=%d\n",
__func__, file_handle);
}
}
exit:
/* If the master was able to send/recv a PIP msg, the IRQ must be ok */
if (slave_irq_toggled)
*slave_irq_toggled = bus_toggled;
if (slave_bus_toggled)
*slave_bus_toggled = bus_toggled;
return rc;
}
/*******************************************************************************
* FUNCTION: pt_ttdl_bist_show
*
* SUMMARY: Show method for the ttdl_bist sysfs node. This built in self test
* will test that I2C/SPI, IRQ and TP_XRES pins are operational.
*
* NOTE: This function will reset the DUT and the startup_status bit
* mask. A pt_enum will be queued after completion.
*
* NOTE: The order of the net tests is done to optimize the time it takes
* to run. The first test is capable of verifying all nets, each subsequent
* test is only run if the previous was not able to see all nets toggle.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_ttdl_bist_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret;
char *bus_err_str = NULL;
char *irq_err_str = NULL;
char *xres_err_str = NULL;
char *slave_bus_err_str = NULL;
char *slave_irq_err_str = NULL;
char *slave_xres_err_str = NULL;
u8 tests;
int rc = 0;
int num_tests = 0;
int status = 1; /* 0 = Pass, !0 = fail */
u8 bus_toggled = 0x0F; /* default to untested */
u8 i2c_toggled = 0x0F; /* default to untested */
u8 spi_toggled = 0x0F; /* default to untested */
u8 irq_toggled = 0x0F; /* default to untested */
u8 xres_toggled = 0x0F; /* default to untested */
u8 slave_bus_toggled = 0x0F; /* default to untested */
u8 slave_irq_toggled = 0x0F; /* default to untested */
u8 slave_xres_toggled = 0x0F; /* default to untested */
bus_err_str = kzalloc(PT_ERR_STR_SIZE, GFP_KERNEL);
irq_err_str = kzalloc(PT_ERR_STR_SIZE, GFP_KERNEL);
xres_err_str = kzalloc(PT_ERR_STR_SIZE, GFP_KERNEL);
if (!bus_err_str || !irq_err_str || !xres_err_str)
goto print_results;
memset(xres_err_str, 0, PT_ERR_STR_SIZE);
memset(irq_err_str, 0, PT_ERR_STR_SIZE);
memset(bus_err_str, 0, PT_ERR_STR_SIZE);
if (cd->multi_chip) {
slave_bus_err_str = kzalloc(PT_ERR_STR_SIZE, GFP_KERNEL);
slave_irq_err_str = kzalloc(PT_ERR_STR_SIZE, GFP_KERNEL);
slave_xres_err_str = kzalloc(PT_ERR_STR_SIZE, GFP_KERNEL);
if (!slave_bus_err_str ||
!slave_irq_err_str ||
!slave_xres_err_str)
goto print_results;
memset(slave_bus_err_str, 0, PT_ERR_STR_SIZE);
memset(slave_irq_err_str, 0, PT_ERR_STR_SIZE);
memset(slave_xres_err_str, 0, PT_ERR_STR_SIZE);
}
/* Turn off the TTDL WD during the test */
pt_stop_wd_timer(cd);
/* Shorten default PIP cmd timeout while running BIST */
cd->pip_cmd_timeout = 200;
/* Count the number of tests to run */
tests = cd->ttdl_bist_select;
while (tests) {
num_tests += tests & 1;
tests >>= 1;
}
pt_debug(dev, DL_ERROR, "%s: BIST select = 0x%02X, run %d tests\n",
__func__, cd->ttdl_bist_select, num_tests);
/* Suppress auto BL to avoid loader thread sending PIP during xres */
if (cd->flashless_dut) {
pt_debug(dev, DL_INFO, "%s Flashless Auto_BL - SUPPRESS\n",
__func__);
mutex_lock(&cd->system_lock);
cd->flashless_auto_bl = PT_SUPPRESS_AUTO_BL;
mutex_unlock(&cd->system_lock);
}
/* --------------- TP_XRES BIST TEST --------------- */
if ((cd->ttdl_bist_select & PT_TTDL_BIST_TP_XRES_TEST) != 0) {
pt_debug(dev, DL_INFO,
"%s: ----- Start TP_XRES BIST -----", __func__);
rc = pt_bist_xres_test(dev, &bus_toggled, &irq_toggled,
&xres_toggled, xres_err_str);
/* Done if the rest of all nets toggled */
if (bus_toggled == 1 && irq_toggled == 1 && xres_toggled == 1)
goto host_nets_complete;
}
/* Flush bus in case a PIP response is waiting from previous test */
pt_flush_bus(cd, PT_FLUSH_BUS_BASED_ON_LEN, NULL);
/* --------------- IRQ BIST TEST --------------- */
if ((cd->ttdl_bist_select & PT_TTDL_BIST_IRQ_TEST) != 0) {
pt_debug(dev, DL_INFO,
"%s: ----- Start IRQ BIST -----", __func__);
bus_toggled = 0xFF;
irq_toggled = 0xFF;
rc = pt_bist_irq_test(dev, &bus_toggled, &irq_toggled,
&xres_toggled, irq_err_str);
/* If this net failed clear results from previous net */
if (irq_toggled != 1) {
xres_toggled = 0x0F;
memset(xres_err_str, 0, PT_ERR_STR_SIZE);
}
if (bus_toggled == 1 && irq_toggled == 1)
goto host_nets_complete;
}
/* Flush bus in case a PIP response is waiting from previous test */
pt_flush_bus(cd, PT_FLUSH_BUS_BASED_ON_LEN, NULL);
/* --------------- BUS BIST TEST --------------- */
if ((cd->ttdl_bist_select & PT_TTDL_BIST_BUS_TEST) != 0) {
pt_debug(dev, DL_INFO,
"%s: ----- Start BUS BIST -----", __func__);
bus_toggled = 0xFF;
rc = pt_bist_bus_test(dev, &bus_toggled, bus_err_str);
/* If this net failed clear results from previous net */
if (bus_toggled == 0) {
irq_toggled = 0x0F;
memset(irq_err_str, 0, PT_ERR_STR_SIZE);
}
}
host_nets_complete:
/* --------------- SLAVE XRES BIST TEST --------------- */
if (cd->multi_chip &&
(cd->ttdl_bist_select & PT_TTDL_BIST_SLAVE_XRES_TEST) != 0) {
pt_debug(dev, DL_INFO,
"%s: ----- Start Slave XRES BIST -----", __func__);
slave_xres_toggled = 0xFF;
rc = pt_bist_slave_xres_test(dev, &slave_irq_toggled,
&slave_bus_toggled, &slave_xres_toggled,
slave_xres_err_str);
if ((slave_bus_toggled == 1 && slave_irq_toggled == 1 &&
slave_xres_toggled == 1) || slave_xres_toggled == 0)
goto print_results;
}
/* --------------- SLAVE IRQ BIST TEST --------------- */
if (cd->multi_chip &&
(cd->ttdl_bist_select & PT_TTDL_BIST_SLAVE_IRQ_TEST) != 0) {
pt_debug(dev, DL_INFO,
"%s: ----- Start Slave IRQ BIST -----", __func__);
slave_irq_toggled = 0xFF;
rc = pt_bist_slave_irq_test(dev, &slave_irq_toggled,
&slave_bus_toggled, slave_irq_err_str, NULL, NULL);
pt_debug(dev, DL_INFO, "%s: slave_irq_toggled = 0x%02X\n",
__func__, slave_irq_toggled);
if (slave_irq_toggled == 1) {
slave_bus_toggled = 1;
goto print_results;
}
}
/* --------------- SLAVE BUS BIST TEST --------------- */
if (cd->multi_chip &&
(cd->ttdl_bist_select & PT_TTDL_BIST_SLAVE_BUS_TEST) != 0) {
pt_debug(dev, DL_INFO,
"%s: ----- Start Slave BUS BIST -----", __func__);
slave_bus_toggled = 0xFF;
rc = pt_bist_slave_bus_test(dev, &slave_irq_toggled,
&slave_bus_toggled, slave_bus_err_str);
}
print_results:
/* Restore PIP command timeout */
cd->pip_cmd_timeout = cd->pip_cmd_timeout_default;
/*
* We're done! - Perform a hard XRES toggle, allowing BL
* to load FW if there is any in Flash
*/
mutex_lock(&cd->system_lock);
cd->hid_reset_cmd_state = 0;
mutex_unlock(&cd->system_lock);
pt_debug(dev, DL_INFO,
"%s: TTDL BIST Complete - Final reset\n", __func__);
if (cd->flashless_dut) {
/*
* For Flashless solution, FW update is triggered after BL is
* seen that several miliseconds delay is needed.
*/
pt_debug(dev, DL_INFO, "%s Flashless Auto_BL - ALLOW\n",
__func__);
mutex_lock(&cd->system_lock);
cd->flashless_auto_bl = PT_ALLOW_AUTO_BL;
mutex_unlock(&cd->system_lock);
/* Reset DUT and wait 100ms to see if loader started */
pt_hw_hard_reset(cd);
msleep(100);
if (cd->fw_updating) {
pt_debug(dev, DL_INFO,
"%s: ----- BIST Wait FW Loading ----",
__func__);
rc = _pt_request_wait_for_enum_state(
dev, 4000, STARTUP_STATUS_COMPLETE);
}
} else {
if (cd->mode == PT_MODE_BOOTLOADER) {
rc = pt_pip2_launch_app(dev, PT_CORE_CMD_PROTECTED);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s Failed to launch app\n", __func__);
rc = pt_hw_hard_reset(cd);
}
}
/*
* If FW exists the BL may have just started or will start soon,
* so the FW sentinel may be on it's way but with no FW it will
* not arrive, wait for it before deciding if we need to queue
* an enum.
*/
rc = _pt_request_wait_for_enum_state(
dev, 400, STARTUP_STATUS_FW_RESET_SENTINEL);
if ((cd->startup_status & STARTUP_STATUS_FW_RESET_SENTINEL) &&
(cd->startup_status & STARTUP_STATUS_COMPLETE) == 0) {
pt_debug(dev, DL_INFO, "%s: ----- BIST Enum ----",
__func__);
pt_queue_enum(cd);
rc = _pt_request_wait_for_enum_state(
dev, 2000, STARTUP_STATUS_COMPLETE);
}
}
msleep(20);
/* --------------- PRINT OUT BIST RESULTS ---------------*/
pt_debug(dev, DL_INFO, "%s: ----- BIST Print Results ----", __func__);
pt_start_wd_timer(cd);
/* Canned print if any memory allocation issues */
if (!bus_err_str || !irq_err_str || !xres_err_str) {
ret = scnprintf(buf, strlen(buf),
"Status: %d\n"
"I2C (SDA,SCL): [UNTEST]\n"
"SPI (MISO,MOSI,CS,CLK): [UNTEST]\n"
"IRQ connection: [UNTEST]\n"
"TP_XRES connection: [UNTEST]\n", -ENOMEM);
if (cd->multi_chip) {
ret += scnprintf(buf + ret, strlen(buf),
"I/P SPI (MISO,MOSI,CS,CLK): [UNTEST]\n"
"I/P IRQ connection: [UNTEST]\n"
"I/P TP_XRES connection: [UNTEST]\n");
}
} else {
status = 0;
if (bus_toggled == 1)
memset(bus_err_str, 0, PT_ERR_STR_SIZE);
if (irq_toggled == 1)
memset(irq_err_str, 0, PT_ERR_STR_SIZE);
if (xres_toggled == 1)
memset(xres_err_str, 0, PT_ERR_STR_SIZE);
if (cd->ttdl_bist_select & PT_TTDL_BIST_BUS_TEST)
status += bus_toggled;
if (cd->ttdl_bist_select & PT_TTDL_BIST_IRQ_TEST)
status += irq_toggled;
if (cd->ttdl_bist_select & PT_TTDL_BIST_TP_XRES_TEST)
status += xres_toggled;
pt_debug(dev, DL_ERROR, "%s: status = %d (%d,%d,%d)\n",
__func__, status, bus_toggled, irq_toggled,
xres_toggled);
if (cd->multi_chip) {
if (slave_irq_toggled == 1)
memset(slave_irq_err_str, 0, PT_ERR_STR_SIZE);
if (slave_xres_toggled == 1)
memset(slave_xres_err_str, 0, PT_ERR_STR_SIZE);
if (slave_bus_toggled == 1)
memset(slave_bus_err_str, 0, PT_ERR_STR_SIZE);
if (cd->ttdl_bist_select & PT_TTDL_BIST_SLAVE_BUS_TEST)
status += slave_bus_toggled;
if (cd->ttdl_bist_select & PT_TTDL_BIST_SLAVE_IRQ_TEST)
status += slave_irq_toggled;
if (cd->ttdl_bist_select & PT_TTDL_BIST_SLAVE_XRES_TEST)
status += slave_xres_toggled;
pt_debug(dev, DL_ERROR,
"%s: status = %d (%d,%d,%d,%d,%d,%d)\n",
__func__, status, bus_toggled, irq_toggled,
xres_toggled, slave_bus_toggled,
slave_irq_toggled, slave_xres_toggled);
}
if (cd->bus_ops->bustype == BUS_I2C)
i2c_toggled = bus_toggled;
else
spi_toggled = bus_toggled;
ret = scnprintf(buf, strlen(buf),
"Status: %d\n"
"I2C (SDA,SCL): %s %s\n"
"SPI (MISO,MOSI,CS,CLK): %s %s\n"
"IRQ connection: %s %s\n"
"TP_XRES connection: %s %s\n",
status == num_tests ? 0 : 1,
i2c_toggled == 0x0F ? "[UNTEST]" :
i2c_toggled == 1 ? "[ OK ]" : "[FAILED]",
i2c_toggled == 0x0F ? "" : bus_err_str,
spi_toggled == 0x0F ? "[UNTEST]" :
spi_toggled == 1 ? "[ OK ]" : "[FAILED]",
spi_toggled == 0x0F ? "" : bus_err_str,
irq_toggled == 0x0F ? "[UNTEST]" :
irq_toggled == 1 ? "[ OK ]" : "[FAILED]",
irq_err_str,
xres_toggled == 0x0F ? "[UNTEST]" :
xres_toggled == 1 ? "[ OK ]" : "[FAILED]",
xres_err_str);
if (cd->multi_chip) {
ret += scnprintf(buf + ret, strlen(buf),
"I/P SPI (MISO,MOSI,CS,CLK): %s %s\n"
"I/P IRQ connection: %s %s\n"
"I/P TP_XRES connection: %s %s\n",
slave_bus_toggled == 0x0F ? "[UNTEST]" :
slave_bus_toggled == 1 ? "[ OK ]" :
"[FAILED]", slave_bus_err_str,
slave_irq_toggled == 0x0F ? "[UNTEST]" :
slave_irq_toggled == 1 ? "[ OK ]" :
"[FAILED]", slave_irq_err_str,
slave_xres_toggled == 0x0F ? "[UNTEST]" :
slave_xres_toggled == 1 ? "[ OK ]" :
"[FAILED]", slave_xres_err_str);
}
}
/* Put TTDL back into a known state, issue a ttdl enum if needed */
pt_debug(dev, DL_INFO, "%s: Startup_status = 0x%04X\n",
__func__, cd->startup_status);
kfree(bus_err_str);
kfree(irq_err_str);
kfree(xres_err_str);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_ttdl_bist_store
*
* SUMMARY: Store method for the ttdl_bist sysfs node.
*
* RETURN: Size of passed in buffer if successful
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to command buffer
* size - size of buf
******************************************************************************/
static ssize_t pt_ttdl_bist_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u32 input_data[2] = {0};
int length;
int rc = 0;
/* Maximum input of one value */
length = _pt_ic_parse_input(dev, buf, size, input_data,
ARRAY_SIZE(input_data));
if (length != 1) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
} else {
mutex_lock(&cd->system_lock);
cd->ttdl_bist_select = input_data[0];
mutex_unlock(&cd->system_lock);
}
exit:
if (rc)
return rc;
return size;
}
static DEVICE_ATTR(ttdl_bist, 0644, pt_ttdl_bist_show,
pt_ttdl_bist_store);
/*******************************************************************************
* FUNCTION: pt_flush_bus_store
*
* SUMMARY: Store method for the flush_bus sysfs node.
*
* RETURN: Size of passed in buffer if successful
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to command buffer
* size - size of buf
******************************************************************************/
static ssize_t pt_flush_bus_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u32 input_data[2] = {0};
int length;
int rc = 0;
/* Maximum input of one value */
length = _pt_ic_parse_input(dev, buf, size, input_data,
ARRAY_SIZE(input_data));
if (length != 1) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
}
mutex_lock(&cd->system_lock);
if (input_data[0] == 0)
cd->flush_bus_type = PT_FLUSH_BUS_BASED_ON_LEN;
else if (input_data[0] == 1)
cd->flush_bus_type = PT_FLUSH_BUS_FULL_256_READ;
else
rc = -EINVAL;
mutex_unlock(&cd->system_lock);
exit:
if (rc)
return rc;
return size;
}
/*******************************************************************************
* FUNCTION: pt_flush_bus_show
*
* SUMMARY: Show method for the flush_bus sysfs node that flushes the active bus
* based on either the size of the first two bytes or a blind 256 bytes.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_flush_bus_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
ssize_t ret = 0;
ssize_t bytes = 0;
struct pt_core_data *cd = dev_get_drvdata(dev);
mutex_lock(&cd->system_lock);
bytes = pt_flush_bus(cd, cd->flush_bus_type, NULL);
ret = scnprintf(buf, strlen(buf),
"Status: 0\n"
"%s: %zd\n",
"Bytes flushed", bytes);
mutex_unlock(&cd->system_lock);
return ret;
}
static DEVICE_ATTR(flush_bus, 0644, pt_flush_bus_show,
pt_flush_bus_store);
/*******************************************************************************
* FUNCTION: pt_pip2_ping_test_store
*
* SUMMARY: Store method for the pip2_ping_test sysfs node.
*
* NOTE: The max PIP2 packet size is 255 (payload for PING 247) however
* someone may want to test sending invalid packet lengths so any values
* up to 255 are allowed.
*
* RETURN: Size of passed in buffer if successful
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to command buffer
* size - size of buf
******************************************************************************/
static ssize_t pt_pip2_ping_test_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u32 input_data[2];
int length;
int rc = 0;
/* Maximum input of one value */
length = _pt_ic_parse_input(dev, buf, size, input_data,
ARRAY_SIZE(input_data));
if (length != 1) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
}
mutex_lock(&cd->system_lock);
if (input_data[1] >= 0 && input_data[0] <= PT_MAX_PIP2_MSG_SIZE)
cd->ping_test_size = input_data[0];
else
rc = -EINVAL;
mutex_unlock(&cd->system_lock);
exit:
if (rc)
return rc;
return size;
}
/*******************************************************************************
* FUNCTION: pt_ping_test_show
*
* SUMMARY: Show method for the ping_test_show sysfs node that sends the PIP2
* PING command and ramps up the optional payload from 0 to
* ping_test_size.
* The max payload size is 247:
* (255 - 2 byte reg address - 4 byte header - 2 byte CRC)
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_pip2_ping_test_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret;
int last_packet_size;
int rc = 0;
rc = pt_pip2_ping_test(dev, cd->ping_test_size, &last_packet_size);
if (rc) {
ret = scnprintf(buf, strlen(buf), "Status: %d\n", rc);
return ret;
}
ret = scnprintf(buf, strlen(buf),
"Status: %d\n"
"PING payload test passed with packet sizes 0 - %d\n",
(last_packet_size == cd->ping_test_size ? 0 : 1),
last_packet_size);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_t_refresh_store
*
* SUMMARY: Store method for the t-refresh sysfs node that will takes a passed
* in integer as the number of interrupts to count. A timer is started to
* calculate the total time it takes to see that number of interrupts.
*
* RETURN: Size of passed in buffer if successful
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to buffer that hold the command parameters
* size - size of buf
******************************************************************************/
static ssize_t pt_t_refresh_store(struct device *dev,
struct device_attribute *attr, const char *buf, size_t size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
u32 input_data[2];
int length;
int rc = 0;
/* Maximum input of one value */
length = _pt_ic_parse_input(dev, buf, size, input_data,
ARRAY_SIZE(input_data));
if (length != 1) {
pt_debug(dev, DL_ERROR, "%s: Invalid number of arguments\n",
__func__);
rc = -EINVAL;
goto exit;
}
mutex_lock(&cd->system_lock);
pt_debug(dev, DL_INFO, "%s: Input value: %d\n", __func__,
input_data[0]);
if (input_data[0] >= 0 && input_data[0] <= 1000) {
cd->t_refresh_total = input_data[0];
cd->t_refresh_count = 0;
cd->t_refresh_active = 1;
} else {
pt_debug(dev, DL_ERROR, "%s: Invalid value\n", __func__);
rc = -EINVAL;
}
mutex_unlock(&cd->system_lock);
exit:
pt_debug(dev, DL_ERROR, "%s: rc = %d\n", __func__, rc);
if (rc)
return rc;
return size;
}
/*******************************************************************************
* FUNCTION: pt_t_refresh_show
*
* SUMMARY: Show method for the t-refresh sysfs node that will show the results
* of the T-Refresh timer counting the time it takes to see a user defined
* number of interrupts.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_t_refresh_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
ssize_t ret = 0;
struct pt_core_data *cd = dev_get_drvdata(dev);
u32 whole;
u16 fraction;
mutex_lock(&cd->system_lock);
/* Check if we have counted the number requested */
if (cd->t_refresh_count != cd->t_refresh_total) {
ret = scnprintf(buf, strlen(buf),
"Status: 0\n"
"%s: %d\n",
"Still counting... current IRQ count",
cd->t_refresh_count);
} else {
/* Ensure T-Refresh is de-activated */
cd->t_refresh_active = 0;
whole = cd->t_refresh_time / cd->t_refresh_count;
fraction = cd->t_refresh_time % cd->t_refresh_count;
fraction = fraction * 1000 / cd->t_refresh_count;
ret = scnprintf(buf, strlen(buf),
"Status: 0\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d\n"
"%s: %d.%02d\n",
"Requested IRQ Count ", cd->t_refresh_total,
"IRQ Counted ", cd->t_refresh_count,
"Total Time Elapsed (ms) ", (int)cd->t_refresh_time,
"Average T-Refresh (ms) ", whole, fraction);
}
mutex_unlock(&cd->system_lock);
return ret;
}
/*******************************************************************************
* FUNCTION: pt_dut_status_show
*
* SUMMARY: Show method for DUT status sysfs node. Display DUT's scan state, and
* more items such as operation mode,easywake state are added in the future.
*
* RETURN: Char buffer with printed scan status information
*
* PARAMETERS:
* *dev - pointer to device structure
* *attr - pointer to device attributes
* *buf - pointer to output buffer
******************************************************************************/
static ssize_t pt_dut_status_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
u8 sys_mode = FW_SYS_MODE_UNDEFINED;
u8 mode = PT_MODE_UNKNOWN;
char *outputstring[7] = {"BOOT", "SCANNING", "DEEP_SLEEP",
"TEST", "DEEP_STANDBY", "UNDEFINED", "n/a"};
struct pt_core_data *cd = dev_get_drvdata(dev);
ssize_t ret;
u16 calculated_crc = 0;
u16 stored_crc = 0;
u8 status;
int rc = 0;
/* In STANDBY the DUT will not repond to any PIP cmd */
if (cd->fw_sys_mode_in_standby_state) {
mode = PT_MODE_OPERATIONAL;
sys_mode = FW_SYS_MODE_DEEP_STANDBY;
goto print_limited_results;
}
/* Retrieve mode and FW system mode which can only be 0-4 */
rc = pt_get_fw_sys_mode(cd, &sys_mode, &mode);
if (rc || mode == PT_MODE_UNKNOWN) {
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE,
"%s: %d\n"
"%s: n/a\n"
"%s: n/a\n"
"%s: n/a\n"
"%s: n/a\n",
"Status", rc,
"Active Exec ",
"FW System Mode ",
"Stored CRC ",
"Calculated CRC ");
return ret;
} else {
if (mode == PT_MODE_OPERATIONAL) {
if (sys_mode > FW_SYS_MODE_MAX)
sys_mode = FW_SYS_MODE_UNDEFINED;
if (sys_mode != FW_SYS_MODE_TEST)
goto print_limited_results;
rc = pt_pip_verify_config_block_crc_(cd,
PT_TCH_PARM_EBID, &status,
&calculated_crc, &stored_crc);
if (rc)
goto print_limited_results;
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE,
"%s: %d\n"
"%s: %s\n"
"%s: %s\n"
"%s: 0x%04X\n"
"%s: 0x%04X\n",
"Status", rc,
"Active Exec ", "FW",
"FW System Mode ", outputstring[sys_mode],
"Stored CRC ", stored_crc,
"Calculated CRC ", calculated_crc);
return ret;
} else {
/* When in BL or unknon mode Active Exec is "n/a" */
sys_mode = FW_SYS_MODE_UNDEFINED + 1;
}
}
print_limited_results:
ret = scnprintf(buf, PT_MAX_PRBUF_SIZE,
"%s: %d\n"
"%s: %s\n"
"%s: %s\n"
"%s: n/a\n"
"%s: n/a\n",
"Status", rc,
"Active Exec ",
mode == PT_MODE_OPERATIONAL ? "FW" : "BL",
"FW System Mode ", outputstring[sys_mode],
"Stored CRC ",
"Calculated CRC ");
return ret;
}
#endif /* TTDL_DIAGNOSTICS */
/*******************************************************************************
* Structures of sysfs attributes for all DUT dependent sysfs node
******************************************************************************/
static struct attribute *early_attrs[] = {
&dev_attr_hw_version.attr,
&dev_attr_drv_version.attr,
&dev_attr_drv_ver.attr,
&dev_attr_fw_version.attr,
&dev_attr_sysinfo.attr,
&dev_attr_pip2_cmd_rsp.attr,
&dev_attr_command.attr,
&dev_attr_drv_debug.attr,
&dev_attr_hw_reset.attr,
&dev_attr_response.attr,
&dev_attr_ttdl_restart.attr,
#ifdef TTDL_DIAGNOSTICS
&dev_attr_ttdl_status.attr,
&dev_attr_pip2_enter_bl.attr,
&dev_attr_pip2_exit_bl.attr,
&dev_attr_err_gpio.attr,
&dev_attr_flush_bus.attr,
&dev_attr_ttdl_bist.attr,
#endif /* TTDL_DIAGNOSTICS */
NULL,
};
static struct attribute_group early_attr_group = {
.attrs = early_attrs,
};
static struct device_attribute pip2_attributes[] = {
__ATTR(pip2_version, 0444, pt_pip2_version_show, NULL),
__ATTR(pip2_gpio_read, 0444, pt_pip2_gpio_read_show, NULL),
#ifdef TTDL_DIAGNOSTICS
__ATTR(pip2_bin_hdr, 0444, pt_pip2_bin_hdr_show, NULL),
__ATTR(pip2_ping_test, 0644, pt_pip2_ping_test_show,
pt_pip2_ping_test_store),
#endif
};
static struct device_attribute attributes[] = {
__ATTR(dut_debug, 0644,
pt_dut_debug_show, pt_drv_debug_store),
__ATTR(sleep_status, 0444, pt_sleep_status_show, NULL),
__ATTR(panel_id, 0444, pt_panel_id_show, NULL),
__ATTR(get_param, 0644,
pt_get_param_show, pt_get_param_store),
__ATTR(pt_touch_offload, 0644,
pt_touch_offload_show, pt_touch_offload_store),
#ifdef EASYWAKE_TSG6
__ATTR(easy_wakeup_gesture, 0644, pt_easy_wakeup_gesture_show,
pt_easy_wakeup_gesture_store),
__ATTR(easy_wakeup_gesture_id, 0444,
pt_easy_wakeup_gesture_id_show, NULL),
__ATTR(easy_wakeup_gesture_data, 0444,
pt_easy_wakeup_gesture_data_show, NULL),
#endif
#ifdef TTDL_DIAGNOSTICS
__ATTR(platform_data, 0444, pt_platform_data_show, NULL),
__ATTR(drv_irq, 0644, pt_drv_irq_show, pt_drv_irq_store),
__ATTR(dut_status, 0444, pt_dut_status_show, NULL),
__ATTR(t_refresh, 0644, pt_t_refresh_show, pt_t_refresh_store),
#endif /* TTDL_DIAGNOSTICS */
};
/*******************************************************************************
* FUNCTION: add_sysfs_interfaces
*
* SUMMARY: Creates all DUT dependent sysfs nodes owned by the core
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static int add_sysfs_interfaces(struct device *dev)
{
int i;
int j = 0;
struct pt_core_data *cd = dev_get_drvdata(dev);
for (i = 0; i < ARRAY_SIZE(attributes); i++) {
if (device_create_file(dev, attributes + i))
goto undo;
}
pt_debug(dev, DL_INFO, "%s: Active DUT Generation: %d",
__func__, cd->active_dut_generation);
if (cd->active_dut_generation == DUT_PIP2_CAPABLE) {
for (j = 0; j < ARRAY_SIZE(pip2_attributes); j++) {
if (device_create_file(dev, pip2_attributes + j))
goto undo;
}
}
return 0;
undo:
for (i--; i >= 0; i--)
device_remove_file(dev, attributes + i);
for (j--; j >= 0; j--)
device_remove_file(dev, pip2_attributes + j);
pt_debug(dev, DL_ERROR, "%s: failed to create sysfs interface\n",
__func__);
return -ENODEV;
}
/*******************************************************************************
* FUNCTION: remove_sysfs_interfaces
*
* SUMMARY: Removes all DUT dependent sysfs nodes owned by the core
*
* RETURN: void
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static void remove_sysfs_interfaces(struct device *dev)
{
int i;
for (i = 0; i < ARRAY_SIZE(attributes); i++)
device_remove_file(dev, attributes + i);
for (i = 0; i < ARRAY_SIZE(pip2_attributes); i++)
device_remove_file(dev, pip2_attributes + i);
}
/*******************************************************************************
* FUNCTION: remove_sysfs_and_modules
*
* SUMMARY: Removes all DUT dependent sysfs nodes and modules
*
* RETURN: void
*
* PARAMETERS:
* *dev - pointer to device structure
******************************************************************************/
static void remove_sysfs_and_modules(struct device *dev)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
/* Queued work should be removed before to release loader module */
call_atten_cb(cd, PT_ATTEN_CANCEL_LOADER, 0);
pt_release_modules(cd);
pt_btn_release(dev);
pt_mt_release(dev);
remove_sysfs_interfaces(dev);
}
static int pt_ts_pinctrl_init(struct pt_core_data *cd)
{
int retval;
/* Get pinctrl if target uses pinctrl */
cd->ts_pinctrl = devm_pinctrl_get(cd->dev);
if (IS_ERR_OR_NULL(cd->ts_pinctrl)) {
retval = PTR_ERR(cd->ts_pinctrl);
dev_dbg(cd->dev,
"Target does not use pinctrl %d\n", retval);
goto err_pinctrl_get;
}
cd->pinctrl_state_active
= pinctrl_lookup_state(cd->ts_pinctrl,
PINCTRL_STATE_ACTIVE);
if (IS_ERR_OR_NULL(cd->pinctrl_state_active)) {
retval = PTR_ERR(cd->pinctrl_state_active);
dev_err(cd->dev,
"Can not lookup %s pinstate %d\n",
PINCTRL_STATE_ACTIVE, retval);
goto err_pinctrl_lookup;
}
cd->pinctrl_state_suspend
= pinctrl_lookup_state(cd->ts_pinctrl,
PINCTRL_STATE_SUSPEND);
if (IS_ERR_OR_NULL(cd->pinctrl_state_suspend)) {
retval = PTR_ERR(cd->pinctrl_state_suspend);
dev_err(cd->dev,
"Can not lookup %s pinstate %d\n",
PINCTRL_STATE_SUSPEND, retval);
goto err_pinctrl_lookup;
}
cd->pinctrl_state_release
= pinctrl_lookup_state(cd->ts_pinctrl,
PINCTRL_STATE_RELEASE);
if (IS_ERR_OR_NULL(cd->pinctrl_state_release)) {
retval = PTR_ERR(cd->pinctrl_state_release);
dev_dbg(cd->dev,
"Can not lookup %s pinstate %d\n",
PINCTRL_STATE_RELEASE, retval);
}
return 0;
err_pinctrl_lookup:
devm_pinctrl_put(cd->ts_pinctrl);
err_pinctrl_get:
cd->ts_pinctrl = NULL;
return retval;
}
void touch_notify_glink_pt_channel_state(bool state)
{
pr_info("%s:[touch] touch_notify_glink\n", __func__);
}
void glink_touch_pt_rx_msg(void *data, int len)
{
int rc = 0;
pr_info("%s: TOUCH_RX_MSG Start:\n", __func__);
if (len > TOUCH_GLINK_INTENT_SIZE) {
pr_err("Invalid TOUCH glink intent size\n");
return;
}
/* check SLATE response */
pt_slate_resp_ack = *(uint32_t *)&data[8];
if (pt_slate_resp_ack == 0x01) {
pr_err("Bad SLATE response\n");
rc = -EINVAL;
goto err_ret;
}
pr_info("%s: TOUCH_RX_MSG End:\n", __func__);
err_ret:
return;
}
/*******************************************************************************
*******************************************************************************
* FUNCTION: pt_probe
*
* SUMMARY: Probe of the core module.
*
* NOTE: For the Parade Technologies development platform (PtSBC) the
* probe functionality is split into two functions; pt_probe() and
* pt_probe_complete(). the initial setup is done in this function which
* then creates a WORK task which runs after the probe timer expires. This
* ensures the I2C/SPI is up on the PtSBC in time for TTDL.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *ops - pointer to the bus
* *dev - pointer to the device structure
* irq - IRQ
* xfer_buf_size - size of the buffer
******************************************************************************/
int pt_probe(const struct pt_bus_ops *ops, struct device *dev,
u16 irq, size_t xfer_buf_size)
{
struct pt_core_data *cd;
struct pt_platform_data *pdata = dev_get_platdata(dev);
enum pt_atten_type type;
struct i2c_client *client = to_i2c_client(dev);
int rc = 0;
u8 pip_ver_major;
u8 pip_ver_minor;
u32 status = STARTUP_STATUS_START;
if (!pdata || !pdata->core_pdata || !pdata->mt_pdata) {
pt_debug(dev, DL_ERROR, "%s: Missing platform data\n",
__func__);
rc = -ENODEV;
goto error_no_pdata;
}
if (pdata->core_pdata->flags & PT_CORE_FLAG_POWEROFF_ON_SLEEP) {
if (!pdata->core_pdata->power) {
pt_debug(dev, DL_ERROR,
"%s: Missing platform data function\n",
__func__);
rc = -ENODEV;
goto error_no_pdata;
}
}
/* get context and debug print buffers */
cd = kzalloc(sizeof(*cd), GFP_KERNEL);
if (!cd) {
rc = -ENOMEM;
goto error_no_pdata;
}
/* Initialize device info */
cd->dev = dev;
cd->pdata = pdata;
cd->cpdata = pdata->core_pdata;
cd->bus_ops = ops;
cd->debug_level = PT_INITIAL_DEBUG_LEVEL;
cd->show_timestamp = PT_INITIAL_SHOW_TIME_STAMP;
scnprintf(cd->core_id, 20, "%s%d", PT_CORE_NAME, core_number++);
cd->hw_detected = false;
cd->pip2_prot_active = false;
cd->pip2_send_user_cmd = false;
cd->bl_pip_ver_ready = false;
cd->app_pip_ver_ready = false;
cd->pip2_cmd_tag_seq = 0x08; /* PIP2 TAG=1 and 3 bit SEQ=0 */
cd->get_param_id = 0;
cd->watchdog_enabled = 0;
cd->startup_retry_count = 0;
cd->core_probe_complete = 0;
cd->fw_system_mode = FW_SYS_MODE_BOOT;
cd->pip_cmd_timeout = PT_PIP_CMD_DEFAULT_TIMEOUT;
cd->pip_cmd_timeout_default = PT_PIP_CMD_DEFAULT_TIMEOUT;
cd->flashless_dut = 0;
cd->flashless_auto_bl = PT_SUPPRESS_AUTO_BL;
cd->bl_with_no_int = 0;
cd->cal_cache_in_host = PT_FEATURE_DISABLE;
cd->multi_chip = PT_FEATURE_DISABLE;
cd->tthe_hid_usb_format = PT_FEATURE_DISABLE;
cd->sleep_state = SS_SLEEP_NONE;
cd->quick_boot = false;
cd->drv_debug_suspend = false;
cd->touch_offload = false;
if (cd->cpdata->config_dut_generation == CONFIG_DUT_PIP2_CAPABLE) {
cd->set_dut_generation = true;
cd->active_dut_generation = DUT_PIP2_CAPABLE;
} else if (cd->cpdata->config_dut_generation == CONFIG_DUT_PIP1_ONLY) {
cd->set_dut_generation = true;
cd->active_dut_generation = DUT_PIP1_ONLY;
} else {
cd->set_dut_generation = false;
cd->active_dut_generation = DUT_UNKNOWN;
}
/* Initialize with platform data */
cd->watchdog_force_stop = cd->cpdata->watchdog_force_stop;
cd->watchdog_interval = PT_WATCHDOG_TIMEOUT;
cd->hid_cmd_state = 1;
cd->fw_updating = false;
cd->multi_chip = 0;
#ifdef TTDL_DIAGNOSTICS
cd->t_refresh_active = 0;
cd->t_refresh_count = 0;
cd->pip2_crc_error_count = 0;
cd->wd_xres_count = 0;
cd->bl_retry_packet_count = 0;
cd->file_erase_timeout_count = 0;
cd->show_tt_data = false;
cd->flush_bus_type = PT_FLUSH_BUS_BASED_ON_LEN;
cd->err_gpio = 0;
cd->err_gpio_type = PT_ERR_GPIO_NONE;
cd->ttdl_bist_select = 0x07;
cd->force_pip2_seq = 0;
#endif /* TTDL_DIAGNOSTICS */
memset(cd->pip2_us_file_path, 0, PT_MAX_PATH_SIZE);
memcpy(cd->pip2_us_file_path, PT_PIP2_BIN_FILE_PATH,
sizeof(PT_PIP2_BIN_FILE_PATH));
pt_init_hid_descriptor(&cd->hid_desc);
/* Read and store the descriptor lengths */
cd->hid_core.hid_report_desc_len =
le16_to_cpu(cd->hid_desc.report_desc_len);
cd->hid_core.hid_max_input_len =
le16_to_cpu(cd->hid_desc.max_input_len);
cd->hid_core.hid_max_output_len =
le16_to_cpu(cd->hid_desc.max_output_len);
/* Initialize mutexes and spinlocks */
mutex_init(&cd->module_list_lock);
mutex_init(&cd->system_lock);
mutex_init(&cd->sysfs_lock);
mutex_init(&cd->ttdl_restart_lock);
mutex_init(&cd->firmware_class_lock);
spin_lock_init(&cd->spinlock);
/* Initialize module list */
INIT_LIST_HEAD(&cd->module_list);
/* Initialize attention lists */
for (type = 0; type < PT_ATTEN_NUM_ATTEN; type++)
INIT_LIST_HEAD(&cd->atten_list[type]);
/* Initialize parameter list */
INIT_LIST_HEAD(&cd->param_list);
/* Initialize wait queue */
init_waitqueue_head(&cd->wait_q);
rc = pt_ts_pinctrl_init(cd);
if (!rc && cd->ts_pinctrl) {
/*
* Pinctrl handle is optional. If pinctrl handle is found
* let pins to be configured in active state. If not
* found continue further without error.
*/
rc = pinctrl_select_state(cd->ts_pinctrl,
cd->pinctrl_state_active);
if (rc < 0)
dev_err(&client->dev, "failed to select pin to active state\n");
}
rc = pt_get_regulator(cd, true);
if (rc) {
dev_err(&client->dev, "Failed to get voltage regulators\n");
goto error_alloc_data;
}
rc = pt_enable_regulator(cd, true);
if (rc) {
dev_err(dev, "Failed to enable regulators: rc=%d\n", rc);
goto error_get_regulator;
}
/* Initialize works */
INIT_WORK(&cd->enum_work, pt_enum_work_function);
INIT_WORK(&cd->ttdl_restart_work, pt_restart_work_function);
INIT_WORK(&cd->watchdog_work, pt_watchdog_work);
/* Initialize HID specific data */
cd->hid_core.hid_vendor_id = (cd->cpdata->vendor_id) ?
cd->cpdata->vendor_id : HID_VENDOR_ID;
cd->hid_core.hid_product_id = (cd->cpdata->product_id) ?
cd->cpdata->product_id : HID_APP_PRODUCT_ID;
cd->hid_core.hid_desc_register =
cpu_to_le16(cd->cpdata->hid_desc_register);
/* Set platform easywake value */
cd->easy_wakeup_gesture = cd->cpdata->easy_wakeup_gesture;
#if defined(CONFIG_DRM) || defined(CONFIG_PANEL_NOTIFIER)
/* Setup active dsi panel */
active_panel = cd->cpdata->active_panel;
#endif
/* Set platform panel_id value */
cd->panel_id_support = cd->cpdata->panel_id_support;
if (cd->panel_id_support & PT_PANEL_ID_BY_SYS_INFO)
/* Set Panel ID to default to 0 */
cd->pid_for_loader = PT_PANEL_ID_DEFAULT;
else
/* Set Panel ID to Not Enabled */
cd->pid_for_loader = PANEL_ID_NOT_ENABLED;
/* Initialize hw_version default to FFFF.FFFF.FF */
snprintf(cd->hw_version, HW_VERSION_LEN_MAX, "FFFF.FFFF.FF");
dev_set_drvdata(dev, cd);
/* PtSBC builds will call this function in pt_probe_complete() */
pt_add_core(dev);
rc = sysfs_create_group(&dev->kobj, &early_attr_group);
if (rc) {
pt_debug(cd->dev, DL_ERROR, "%s:create early attrs failed\n",
__func__);
goto error_enable_regulator;
}
/*
* Save the pointer to a global value, which will be used
* in ttdl_restart function
*/
cd->bus_ops = ops;
glink_touch_channel_init(&touch_notify_glink_pt_channel_state, &glink_touch_pt_rx_msg);
/*
* When the IRQ GPIO is not direclty accessible and no function is
* defined to get the IRQ status, the IRQ passed in must be assigned
* directly as the gpio_to_irq will not work. e.g. CHROMEOS
*/
if (!cd->cpdata->irq_stat) {
cd->irq = irq;
pt_debug(cd->dev, DL_ERROR, "%s:No irq_stat, Set cd->irq = %d\n",
__func__, cd->irq);
}
/* Call platform init function before setting up the GPIO's */
if (cd->cpdata->init) {
pt_debug(cd->dev, DL_INFO, "%s: Init HW\n", __func__);
rc = cd->cpdata->init(cd->cpdata, PT_MT_POWER_ON, cd->dev);
} else {
pt_debug(cd->dev, DL_ERROR, "%s: No HW INIT function\n",
__func__);
rc = 0;
}
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR, "%s: HW Init fail r=%d\n",
__func__, rc);
}
/* Power on any needed regulator(s) */
if (cd->cpdata->setup_power) {
pt_debug(cd->dev, DL_INFO, "%s: Device power on!\n", __func__);
rc = cd->cpdata->setup_power(cd->cpdata,
PT_MT_POWER_ON, cd->dev);
} else {
pt_debug(cd->dev, DL_ERROR, "%s: No setup power function\n",
__func__);
rc = 0;
}
if (rc < 0)
pt_debug(cd->dev, DL_ERROR, "%s: Setup power on fail r=%d\n",
__func__, rc);
#ifdef TTDL_DIAGNOSTICS
cd->watchdog_irq_stuck_count = 0;
cd->bus_transmit_error_count = 0;
#endif /* TTDL_DIAGNOSTICS */
if (cd->cpdata->detect) {
pt_debug(cd->dev, DL_INFO, "%s: Detect HW\n", __func__);
rc = cd->cpdata->detect(cd->cpdata, cd->dev,
pt_platform_detect_read);
if (!rc) {
cd->hw_detected = true;
pt_debug(cd->dev, DL_INFO,
"%s: HW detected\n", __func__);
} else {
cd->hw_detected = false;
pt_debug(cd->dev, DL_INFO,
"%s: No HW detected\n", __func__);
rc = -ENODEV;
goto error_detect;
}
} else {
pt_debug(dev, DL_ERROR,
"%s: PARADE No HW detect function pointer\n",
__func__);
/*
* "hw_reset" is not needed in the "if" statement,
* because "hw_reset" is already included in "hw_detect"
* function.
*/
rc = pt_hw_hard_reset(cd);
if (rc)
pt_debug(cd->dev, DL_ERROR,
"%s: FAILED to execute HARD reset\n",
__func__);
}
if (cd->cpdata->setup_irq) {
pt_debug(cd->dev, DL_INFO, "%s: setup IRQ\n", __func__);
rc = cd->cpdata->setup_irq(cd->cpdata, PT_MT_IRQ_REG, cd->dev);
if (rc) {
pt_debug(dev, DL_ERROR,
"%s: Error, couldn't setup IRQ\n", __func__);
goto error_setup_irq;
}
} else {
pt_debug(dev, DL_ERROR,
"%s: IRQ function pointer not setup\n",
__func__);
goto error_setup_irq;
}
#if (KERNEL_VERSION(4, 14, 0) > LINUX_VERSION_CODE)
setup_timer(&cd->watchdog_timer, pt_watchdog_timer,
(unsigned long)cd);
#else
timer_setup(&cd->watchdog_timer, pt_watchdog_timer, 0);
#endif
pt_stop_wd_timer(cd);
#ifdef TTHE_TUNER_SUPPORT
mutex_init(&cd->tthe_lock);
cd->tthe_debugfs = debugfs_create_file(PT_TTHE_TUNER_FILE_NAME,
0644, NULL, cd, &tthe_debugfs_fops);
#endif
rc = device_init_wakeup(dev, 1);
if (rc < 0)
pt_debug(dev, DL_ERROR, "%s: Error, device_init_wakeup rc:%d\n",
__func__, rc);
if (!enable_irq_wake(cd->irq)) {
cd->irq_wake = 1;
pt_debug(cd->dev, DL_WARN, "%s Device MAY wakeup\n", __func__);
}
pm_runtime_get_noresume(dev);
pm_runtime_set_active(dev);
pm_runtime_enable(dev);
/* If IRQ asserted, read out all from buffer to release INT pin */
if (cd->cpdata->irq_stat) {
pt_flush_bus_if_irq_asserted(cd, PT_FLUSH_BUS_BASED_ON_LEN);
} else {
/* Force a read in case the reset sentinel already arrived */
rc = pt_read_input(cd);
if (!rc)
pt_parse_input(cd);
}
/* Without sleep DUT is not ready and will NAK the first write */
msleep(150);
/* Attempt to set the DUT generation if not yet set */
if (cd->active_dut_generation == DUT_UNKNOWN) {
if (cd->bl_pip_ver_ready ||
(cd->app_pip_ver_ready &&
IS_PIP_VER_GE(&cd->sysinfo, 1, 12))) {
cd->active_dut_generation = DUT_PIP2_CAPABLE;
pt_debug(dev, DL_INFO, "%s: dut generation is %d\n",
__func__, cd->active_dut_generation);
} else {
rc = _pt_detect_dut_generation(cd->dev,
&status, &cd->active_dut_generation,
&cd->mode);
if ((cd->active_dut_generation == DUT_UNKNOWN)
|| rc) {
pt_debug(cd->dev, DL_ERROR,
" === DUT Gen unknown, Skip Enum ===\n");
goto skip_enum;
}
}
}
_pt_request_active_pip_protocol(cd->dev, PT_CORE_CMD_PROTECTED,
&pip_ver_major, &pip_ver_minor);
if (pip_ver_major == 2) {
cd->bl_pip_ver_ready = true;
pt_debug(dev, DL_ERROR,
" === PIP2.%d Detected, Attempt to launch APP ===\n",
pip_ver_minor);
cd->hw_detected = true;
} else if (pip_ver_major == 1) {
cd->app_pip_ver_ready = true;
pt_debug(dev, DL_ERROR,
" === PIP1.%d Detected ===\n", pip_ver_minor);
cd->hw_detected = true;
} else {
cd->sysinfo.ttdata.pip_ver_major = 0;
cd->sysinfo.ttdata.pip_ver_minor = 0;
cd->app_pip_ver_ready = false;
cd->hw_detected = false;
pt_debug(dev, DL_ERROR,
" === PIP Version Not Detected, Skip Enum ===\n");
/* For legacy DUTS proceed, enum will attempt to launch app */
if (cd->active_dut_generation != DUT_PIP1_ONLY)
goto skip_enum;
}
rc = pt_enum_with_dut(cd, false, &status);
pt_debug(dev, DL_ERROR, "%s: cd->startup_status=0x%04X status=0x%04X\n",
__func__, cd->startup_status, status);
if (rc == -ENODEV) {
pt_debug(cd->dev, DL_ERROR,
"%s: Enumeration Failed r=%d\n", __func__, rc);
/* For PtSBC don't error out, allow TTDL to stay up */
rc = -EPROBE_DEFER;
goto error_after_startup;
}
/* Suspend scanning until probe is complete to avoid asyc touches */
pt_pip_suspend_scanning_(cd);
if (cd->hw_detected) {
pt_debug(dev, DL_INFO, "%s: Add sysfs interfaces\n",
__func__);
rc = add_sysfs_interfaces(dev);
if (rc < 0) {
pt_debug(dev, DL_ERROR,
"%s: Error, fail sysfs init\n", __func__);
goto error_after_startup;
}
} else {
pt_debug(dev, DL_ERROR,
"%s: No HW detected, sysfs interfaces not added\n",
__func__);
}
skip_enum:
pm_runtime_put_sync(dev);
pt_debug(dev, DL_INFO, "%s: Probe: MT, BTN\n", __func__);
rc = pt_mt_probe(dev);
if (rc < 0) {
pt_debug(dev, DL_ERROR, "%s: Error, fail mt probe\n",
__func__);
goto error_after_sysfs_create;
}
rc = pt_btn_probe(dev);
if (rc < 0) {
pt_debug(dev, DL_ERROR, "%s: Error, fail btn probe\n",
__func__);
goto error_after_startup_mt;
}
pt_probe_modules(cd);
#ifdef CONFIG_HAS_EARLYSUSPEND
pt_setup_early_suspend(cd);
#elif defined(CONFIG_PANEL_NOTIFIER)
pt_debug(dev, DL_ERROR, "%s: Probe: Setup Panel Event notifier\n", __func__);
pt_setup_panel_event_notifier(cd);
INIT_WORK(&cd->resume_offload_work, pt_resume_offload_work);
INIT_WORK(&cd->suspend_offload_work, pt_suspend_offload_work);
#elif defined(CONFIG_DRM)
pt_debug(dev, DL_ERROR, "%s: Probe: Setup drm notifier\n", __func__);
pt_setup_drm_notifier(cd);
INIT_WORK(&cd->resume_offload_work, pt_resume_offload_work);
INIT_WORK(&cd->suspend_offload_work, pt_suspend_offload_work);
#elif defined(CONFIG_FB)
pt_setup_fb_notifier(cd);
#endif
#ifdef NEED_SUSPEND_NOTIFIER
cd->pm_notifier.notifier_call = pt_pm_notifier;
register_pm_notifier(&cd->pm_notifier);
#endif
pt_pip_resume_scanning_(cd);
mutex_lock(&cd->system_lock);
cd->startup_status |= status;
cd->core_probe_complete = 1;
mutex_unlock(&cd->system_lock);
pt_core_state = STATE_RESUME;
pt_debug(dev, DL_ERROR, "%s: TTDL Core Probe Completed Successfully\n",
__func__);
return 0;
error_after_startup_mt:
pr_err("%s PARADE error_after_startup_mt\n", __func__);
pt_mt_release(dev);
error_after_sysfs_create:
pr_err("%s PARADE error_after_sysfs_create\n", __func__);
pm_runtime_disable(dev);
#if (KERNEL_VERSION(3, 16, 0) > LINUX_VERSION_CODE)
device_wakeup_disable(dev);
#endif
device_init_wakeup(dev, 0);
cancel_work_sync(&cd->enum_work);
pt_stop_wd_timer(cd);
pt_free_si_ptrs(cd);
remove_sysfs_interfaces(dev);
error_after_startup:
pr_err("%s PARADE error_after_startup\n", __func__);
del_timer(&cd->watchdog_timer);
if (cd->cpdata->setup_irq)
cd->cpdata->setup_irq(cd->cpdata, PT_MT_IRQ_FREE, dev);
error_setup_irq:
error_detect:
if (cd->cpdata->init)
cd->cpdata->init(cd->cpdata, PT_MT_POWER_OFF, dev);
if (cd->cpdata->setup_power)
cd->cpdata->setup_power(cd->cpdata, PT_MT_POWER_OFF, dev);
sysfs_remove_group(&dev->kobj, &early_attr_group);
error_enable_regulator:
pt_del_core(dev);
dev_set_drvdata(dev, NULL);
pt_enable_regulator(cd, false);
error_get_regulator:
pt_get_regulator(cd, false);
error_alloc_data:
kfree(cd);
error_no_pdata:
pr_err("%s failed.\n", __func__);
return rc;
}
/*******************************************************************************
* FUNCTION: pt_device_entry
*
* SUMMARY: Wrapper function of pt_core_suspend_() to help avoid TP from being
* woke up or put to sleep based on Kernel power state even when the display
* is off based on the check of TTDL core platform flag.
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *dev - pointer to core device
******************************************************************************/
#ifdef PT_AMBIENT_MODE
int pt_device_entry(struct device *dev,
u16 irq, size_t xfer_buf_size)
{
struct pt_core_data *cd = dev_get_drvdata(dev);
struct pt_platform_data *pdata = dev_get_platdata(dev);
struct i2c_client *client = to_i2c_client(dev);
int rc = 0;
void *glink_pt_send_msg;
int glink_touch_exit = TOUCH_EXIT;
pt_debug(dev, DL_INFO, "%s: Start pt_device_entry\n", __func__);
cd->dev = dev;
cd->pdata = pdata;
cd->cpdata = pdata->core_pdata;
glink_pt_send_msg = &glink_touch_exit;
pt_debug(dev, DL_INFO, "[touch]glink_pt_send_msg = %d\n", glink_pt_send_msg);
glink_touch_tx_msg(glink_pt_send_msg, TOUCH_MSG_SIZE);
msleep(150);
if (!rc && cd->ts_pinctrl) {
/*
* Pinctrl handle is optional. If pinctrl handle is found
* let pins to be configured in active state. If not
* found continue further without error.
*/
rc = pinctrl_select_state(cd->ts_pinctrl, cd->pinctrl_state_active);
if (rc < 0)
dev_err(&client->dev, "failed to select pin to active state\n");
}
/* Set platform easywake value */
cd->easy_wakeup_gesture = cd->cpdata->easy_wakeup_gesture;
/*
* When the IRQ GPIO is not direclty accessible and no function is
* defined to get the IRQ status, the IRQ passed in must be assigned
* directly as the gpio_to_irq will not work. e.g. CHROMEOS
*/
if (!cd->cpdata->irq_stat) {
cd->irq = irq;
pt_debug(cd->dev, DL_ERROR, "%s:No irq_stat, Set cd->irq = %d\n", __func__, cd->irq);
}
/* Call platform init function before setting up the GPIO's */
if (cd->cpdata->init) {
pt_debug(cd->dev, DL_INFO, "%s: Init HW\n", __func__);
rc = cd->cpdata->init(cd->cpdata, PT_MT_POWER_ON, cd->dev);
} else {
pt_debug(cd->dev, DL_ERROR, "%s: No HW INIT function\n", __func__);
rc = 0;
}
if (rc < 0) {
pt_debug(cd->dev, DL_ERROR, "%s: HW Init fail r=%d\n", __func__, rc);
}
/* Power on any needed regulator(s) */
if (cd->cpdata->setup_power) {
pt_debug(cd->dev, DL_INFO, "%s: Device power on!\n", __func__);
rc = cd->cpdata->setup_power(cd->cpdata, PT_MT_POWER_ON, cd->dev);
} else {
pt_debug(cd->dev, DL_ERROR, "%s: No setup power function\n", __func__);
rc = 0;
}
if (rc < 0)
pt_debug(cd->dev, DL_ERROR, "%s: Setup power on fail r=%d\n", __func__, rc);
if (cd->cpdata->detect) {
pt_debug(cd->dev, DL_INFO, "%s: Detect HW\n", __func__);
rc = cd->cpdata->detect(cd->cpdata, cd->dev, pt_platform_detect_read);
if (!rc) {
cd->hw_detected = true;
pt_debug(cd->dev, DL_INFO, "%s: HW detected\n", __func__);
} else {
cd->hw_detected = false;
pt_debug(cd->dev, DL_INFO, "%s: No HW detected\n", __func__);
rc = -ENODEV;
goto pt_error_detect;
}
} else {
pt_debug(dev, DL_ERROR, "%s: PARADE No HW detect function pointer\n", __func__);
/*
* "hw_reset" is not needed in the "if" statement,
* because "hw_reset" is already included in "hw_detect"
* function.
*/
rc = pt_hw_hard_reset(cd);
if (rc)
pt_debug(cd->dev, DL_ERROR, "%s: FAILED to execute HARD reset\n", __func__);
}
if (cd->cpdata->setup_irq) {
pt_debug(cd->dev, DL_INFO, "%s: setup IRQ\n", __func__);
rc = cd->cpdata->setup_irq(cd->cpdata, PT_MT_IRQ_REG, cd->dev);
if (rc) {
pt_debug(dev, DL_ERROR, "%s: Error, couldn't setup IRQ\n", __func__);
goto pt_error_setup_irq;
}
} else {
pt_debug(dev, DL_ERROR, "%s: IRQ function pointer not setup\n", __func__);
goto pt_error_setup_irq;
}
rc = device_init_wakeup(dev, 1);
if (rc < 0)
pt_debug(dev, DL_ERROR, "%s: Error, device_init_wakeup rc:%d\n", __func__, rc);
if (!enable_irq_wake(cd->irq)) {
cd->irq_wake = 1;
pt_debug(cd->dev, DL_WARN, "%s Device MAY wakeup\n", __func__);
}
pm_runtime_get_noresume(dev);
pm_runtime_set_active(dev);
pm_runtime_enable(dev);
/* Without sleep DUT is not ready and will NAK the first write */
msleep(150);
pm_runtime_put_sync(dev);
#if defined(CONFIG_PANEL_NOTIFIER)
/* Setup active dsi panel */
active_panel = cd->cpdata->active_panel;
pt_debug(dev, DL_ERROR, "%s: Probe: Setup Panel Event notifier\n", __func__);
pt_setup_panel_event_notifier(cd);
#endif
mutex_lock(&cd->system_lock);
cd->core_probe_complete = 1;
mutex_unlock(&cd->system_lock);
pt_debug(dev, DL_INFO, "%s: ####TTDL Core Device Probe Completed Successfully\n", __func__);
pt_core_state = STATE_RESUME;
return 0;
pt_error_setup_irq:
device_init_wakeup(dev, 0);
pt_error_detect:
if (cd->cpdata->init)
cd->cpdata->init(cd->cpdata, PT_MT_POWER_OFF, dev);
if (cd->cpdata->setup_power)
cd->cpdata->setup_power(cd->cpdata, PT_MT_POWER_OFF, dev);
return rc;
}
#endif
EXPORT_SYMBOL_GPL(pt_probe);
/*******************************************************************************
* FUNCTION: pt_release
*
* SUMMARY: This function does the following cleanup:
* - Releases all probed modules
* - Stops the watchdog
* - Cancels all pending work tasks
* - Removes all created sysfs nodes
* - Removes all created debugfs nodes
* - Frees the IRQ
* - Deletes the core
* - Frees all pointers and HID reports
*
* RETURN:
* 0 = success
* !0 = failure
*
* PARAMETERS:
* *cd - pointer to the core data structure
******************************************************************************/
int pt_release(struct pt_core_data *cd)
{
struct device *dev = cd->dev;
/*
* Suspend the device before freeing the startup_work and stopping
* the watchdog since sleep function restarts watchdog on failure
*/
pm_runtime_suspend(dev);
pm_runtime_disable(dev);
/*
* Any 'work' that can trigger a new thread should be canceled first.
* The watchdog is also stopped again because another thread could have
* restarted it. The irq_work is cancelled last because it is used for
* all I2C/SPI communication.
*/
pt_stop_wd_timer(cd);
call_atten_cb(cd, PT_ATTEN_CANCEL_LOADER, 0);
cancel_work_sync(&cd->ttdl_restart_work);
cancel_work_sync(&cd->enum_work);
cancel_work_sync(&cd->resume_offload_work);
cancel_work_sync(&cd->suspend_offload_work);
cancel_work_sync(&cd->resume_work);
cancel_work_sync(&cd->suspend_work);
destroy_workqueue(cd->pt_workqueue);
pt_stop_wd_timer(cd);
pt_release_modules(cd);
pt_proximity_release(dev);
pt_btn_release(dev);
pt_mt_release(dev);
#ifdef CONFIG_HAS_EARLYSUSPEND
unregister_early_suspend(&cd->es);
#elif defined(CONFIG_PANEL_NOTIFIER)
if (active_panel)
panel_event_notifier_unregister(cd->entry);
#elif defined(CONFIG_DRM)
if (active_panel)
drm_panel_notifier_unregister(active_panel, &cd->fb_notifier);
#elif defined(CONFIG_FB)
fb_unregister_client(&cd->fb_notifier);
#endif
#ifdef NEED_SUSPEND_NOTIFIER
unregister_pm_notifier(&cd->pm_notifier);
#endif
#if (KERNEL_VERSION(3, 16, 0) > LINUX_VERSION_CODE)
device_wakeup_disable(dev);
#endif
device_init_wakeup(dev, 0);
#ifdef TTHE_TUNER_SUPPORT
mutex_lock(&cd->tthe_lock);
cd->tthe_exit = 1;
wake_up(&cd->wait_q);
mutex_unlock(&cd->tthe_lock);
debugfs_remove(cd->tthe_debugfs);
#endif
sysfs_remove_group(&dev->kobj, &early_attr_group);
remove_sysfs_interfaces(dev);
disable_irq_nosync(cd->irq);
if (cd->cpdata->setup_irq)
cd->cpdata->setup_irq(cd->cpdata, PT_MT_IRQ_FREE, dev);
if (cd->cpdata->init)
cd->cpdata->init(cd->cpdata, PT_MT_POWER_OFF, dev);
if (cd->cpdata->setup_power)
cd->cpdata->setup_power(cd->cpdata, PT_MT_POWER_OFF, dev);
dev_set_drvdata(dev, NULL);
pt_del_core(dev);
if (cd->vcc_i2c)
regulator_set_load(cd->vcc_i2c, 0);
if (cd->vdd)
regulator_set_load(cd->vdd, 0);
pt_enable_regulator(cd, false);
pt_get_regulator(cd, false);
pt_free_si_ptrs(cd);
kfree(cd);
return 0;
}
EXPORT_SYMBOL_GPL(pt_release);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Parade TrueTouch(R) Standard Product Core Driver");
MODULE_AUTHOR("Parade Technologies <ttdrivers@paradetech.com>");