Add multi-client latency level service bit capability support,
WLAN_SOC_WLM_MULTI_CLIENT_LL_SUPPORT, to check whether the FW
supports multi-client latency level event or not.
Add INI "wlm_multi_client_ll feature" to enable/disable multi
client latency level feature from the host side.
* @min: 0
* @max: 1
* @default: 0
If firmware sends multi-client latency level service
bit capability to host and host enables multi-client latency
level feature via INI, the host waits for an event
WMI_VDEV_LATENCY_LEVEL_EVENTID as a response to a request
command WMI_WLM_CONFIG_CMDID.
Change-Id: I5cbea89e67caabac5db70b7f0a91c18bdd512e9b
CRs-Fixed: 3180928
Currently, for Thermal Throttle service, Multi-Client feature is enabled
for QCA6750 only but now it is enabled for all the targets.
Change-Id: I0afd48c481193d02c473bc7daa2226c9225968ed
CRs-Fixed: 3174679
Add new sysfs entry to enable or disable capture of
datapath tx delay stats per vdev.
Enable HW_TX_DELAY_STATS config flag for Lithium targets
to support capture of tx delay stats at runtime.
Change-Id: I838961daf27e08c4b6e693852c62f9f894f499a5
CRs-Fixed: 2981004
Enable feature DP_RX_DELIVER_ALL_OOR_FRAMES for lithium DP
which will allow all OOR frames to stack.
Change-Id: I3ad59fc3b3fc8e70b2f05a7cfa23e2646c1e03a4
CRs-Fixed: 3152334
Remove CONFIG_WLAN_FEATURE_REDUCE_RX_THREADS compile flag.
Keep num rx_thread dependent on rx REO rings, 1 rx_thread for
each rx REO ring. It is controlled via INI dp_reo_rings_map.
Change-Id: I701e5cec79a8968b540c9437fe297ca1db8cd5d3
CRs-Fixed: 3048265
Add feature flag to support marking first packet after wow wakeup
and enable it for QCA6490.
Change-Id: Icbda6dabe61a113a8aaa87f7a8fd1d95555226a1
CRs-Fixed: 3137627
Currently refill thread is not getting chance to update
refill buffer pool, which is causing the increase in
rx thread time.
To fix issue move refill thread to performace cluster.
Change-Id: I839352ff09da692f801e97f7938a67ab8f09742b
CRs-Fixed: 3138081
Disable monitor mode on sdx65, it will save 5MB buf,
and improve iperf performance.
Disable WIFI_MONITOR_SUPPORT for pdev/vdev/peer do
nothing of monitor mode.
Enable MONITOR_MODULARIZED_ENABLE for monitor_soc
attach do nothing.
Disable QCA_MONITOR_PKT_SUPPORT for monitor ring
which are not initialized in dp_queue_mon_ring_stats.
Change-Id: I9865ad38dbbee56abee567fded17f39ee299ac42
CRs-Fixed: 3069269
Enable the support to parse the common user info from
the tlv in monitor status ring for KIWI.
Change-Id: Id54817efb65c005578c7cc28286feabde1bea652
CRs-Fixed: 3129126
Add support to update tsf timestamp on driver entry and
exit in data packet. This helps debug latency issue in
XR usecases.
Change-Id: I49d190a55b7ab3081225b7a226f1bbe4f717a20f
CRs-Fixed: 3090104
Add "gEnableUpdateScramSeed" ini support to send
WMI_PDEV_PARAM_EN_UPDATE_SCRAM_SEED command to firmware
to enable OFDM scrambler seed.
Change-Id: Ie5c244a7ea418eec0af1f576e8521804ee85a665
CRs-Fixed: 3106348
Always enable ce debug history feature, but there
is difference for perf&debug build.
On perf build, only ce2/ce3 histroy is enabled.
And for ce debug history memory init/deinit happens
when driver is loading&unloading, even it use when start
module, this will help to check some cases when
stop_module happens.
Change-Id: I4b825f91bc9ede8372291f9d94cb7fae23942a49
CRs-Fixed: 3058735
CONFIG_WLAN_TWT_SAP_STA_COUNT and CONFIG_WLAN_TWT_SAP_PDEV_COUNT
are missing for HMT config.
Add this two macro in HMT config
Change-Id: Ib72c91e720711e72761f0a5526fd48c1e6e2ea1b
CRs-Fixed: 3099486
The flags, CONFIG_TX_MULTI_TCL for multi SW2TCL and DFEATURE_IRQ_AFFINITY
for Tx completion IRQ affinity, were turned on for KIWI.
Change-Id: I44a7b1c889d7113f078a75c549a632809dbebad0
CRs-Fixed: 3110299
Enable compile macro to include extended avoid frequency update
for sub vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT.
Change-Id: Ibdec18b9b749f18b1e9d704974f4cbaabbc4e612
CRs-Fixed: 3098824
Replace blacklist/whitelist with denylist/allowlist for
blacklist manager component. and replace blm with dlm.
Change-Id: I8dec146d8cb3b61dc891b72bea44704b8ab733fe
CRs-Fixed: 3087575
Currently there is no support to read bmiss stats from fw.
With this change, add support to read bmiss stats from fw.
Change-Id: I77594d05fbcd295aff4c625ba5f4f33cbc491063
CRs-Fixed: 3097304
Enable CONFIG_DBR_HOLD_LARGE_MEM for QCA6490, to avoid
large memory allocation failure during idle restart.
Change-Id: I8f504f278bab6f4d974e8cf6b778e6c5ab9ec838
CRs-Fixed: 3101976
For Kiwi, forcing UMAC out of power collapse mechanism is not
enabled yet, this might result in UMAC register writing failure.
Enable forcing UMAC out of power collapse for Kiwi
Change-Id: I2d474bbb6b5d2b8c5a9e9621a4f65a5728be74ea
CRs-Fixed: 3086182
Make CFG_TGT_DEFAULT_BEACON_TX_OFFLOAD_MAX_VDEV configurable in code.
Add configure file to support 4SAP concurrency and maximum 4 IPA
interface for sdxlemur.
Change-Id: I18e86aa0eac2902d831d1fb8a4f0fc03666fb6f2
CRs-Fixed: 3092382
Enable monitor mode for WCN7850.
Enable the interrupt based processing in monitor
mode for WCN7850.
Change-Id: I6f8c6951794d0754977fa0d45086a95df25a13e6
CRs-Fixed: 3095456
Currently there is no provision to get the calibration failure
information from the driver. Because of this it is getting difficult
to debug the calibration failure issues.
To simplify the calibration failure issue debugging, add support to
parse calibration failures events in the driver.
Change-Id: I6d831804cca259862fea3e8bb4af33d556138d43
CRs-Fixed: 3078926
Enable TX AST index search for HMT STA which is more efficient
compared with older source address search.
Change-Id: Ie5ebf4199ada959ebd33351929cf642c21657c51
CRs-Fixed: 3084026
Kbuild change to
- Disable timer irq for CE in WCN7850
- Disable status ring timer WAR in WCN7850
Change-Id: I59a247bf14450c5e1ec194c505f3a00eb5f3619f
CRs-Fixed: 3075871
Use CONFIG_SLUB_DEBUG_On to enable certain flags. This ensures that
these flags are not enabled for PERF builds.
Change-Id: I8c8e032ca1a0344f12fbad4dca543e333d601916
CRs-Fixed: 3045963
Enable config flag to use multiple tx and tx completion
ring pairs for qca6750 when IPA is disabled.
Change-Id: Ide99b2f4d912b3bca551438cba522c2f9366b5d2
CRs-Fixed: 3075385
Enable config flag to use multiple tx and tx completion
ring pairs for qca6490 when IPA is disabled.
Change-Id: Iafa6df504d7be55cbc5a233d6975963f0e118df5
CRs-Fixed: 3059736
Enable the below datapath MLO features in Kbuild
- DP_USE_REDUCED_PEER_ID_FIELD_WIDTH
The above feature reduces the width of peer_id from
peer_metadata, thereby reducing the size of the peer
object array.
Change-Id: I58533c241a40184129786f11a47f3722cf005a61
CRs-Fixed: 3059637
Add a sysfs to display DP stats on console. Sysfs file
displays requested stats on console and wlan logs.
Change-Id: Ifd56d1bf6f578a4ce3f1d963040e6d3cd138c64a
CRs-Fixed: 3035860
Fix few missing attribute in below connectivity events:
QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_RESPONSE
QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCORE_CURR_AP
Also send the roam candidate info properly to userspace.
Change-Id: Ia9c4f095316adf8f40294f1e119cad648749bb72
CRs-Fixed: 3037650
Remove the comma between the text of filter key word. So
the macro CONFIG_MOBILE_ROUTER will be enabled.
Change-Id: Ie69aae479470017eee7a266abf3b7456ac38ef26
CRs-Fixed: 3038353
