Add support display emulation targets on RUMI
This change does the following:
-parse dt node to enable display emulation mode.
-use sde_reg_read for pool timeout ops and debug fs dump.
-increases the kickoff timeout when emulation is enabled.
-bypass AXI halt operation when emulation is enabled.
Change-Id: Idc493964c0b8fc89f5d85fcc5755e0874a12d211
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
sde_vbif_get_xin_status is expected to return true if client is idle
and false otherwise. Update the final return status based on this
expectation.
Change-Id: I3a9ff7c83cb5966ff5573b27e5c2e88423448199
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Avoid various possible nullptr dereferences
and check validity of index before accessing
arrays. Addresses issues highlighted by
static analysis.
Change-Id: I5abfbc8c4cacb56e9decc3a6339ab0fa3a63b606
Signed-off-by: Nisarg Bhavsar <quic_bhavsar@quicinc.com>
Use #if IS_ENABLED() instead of #ifdef for configurations as vendor module
guidelines.
Use #if IS_ENABLED(CONFIG_XXX) instead of #ifdef CONFIG_XXX to ensure that
the code inside the #if block continues to compile if the config changes
to a tristate config in the future.
The differences are as follows:
1.#if IS_ENABLED(CONFIG_XXX) evaluates to true when CONFIG_XXX is set to
module (=m) or built-in (=y).
2.#ifdef CONFIG_XXX evaluates to true when CONFIG_XXX is set to
built-in(=y) , but doesn't when CONFIG_XXX is set to module(=m).
Use this only when you're certain you want to do the same thing
when the config is set to module or is disabled.
Change-Id: Ia806b9b01ad8414d0e4de027a382cb68e7fb4a6a
Signed-off-by: GG Hou <quic_renjhou@quicinc.com>
Update the sde HW catalog parsing to get separate values for rp_remap
and lvl_remap for each qos level. Previously, only rp_remap were provided
and the same was applied for lvl_remap. As part of the change, add cnoc
remap level which is added as part of MDSS 9.x.
Change-Id: I112a715f8b33cd4b028886d8074e35fef75b8aab
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
From Kalama onwards, the VBIF CLK_CTRL register has been moved from TOP block
to individual hardware block memory range.
This change is adding a backward compatible solution to support
per block VBIF CLK_CTRL access by allowing each HW block to register
set of callback ops. Additionally, it adds DMA and IPCC/MSI VBIF CLK_CTRL
block type.
Change-Id: Ia82ced34cfa1636b57cd1c03b327faf923be482a
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
CWB may trigger frame missed message if interrupts
are disabled on specific CPU. WB2 will only find single
interrupt status for two posted start triggered frame.
SDE driver will start checking the xin client clock
status for wb2 timeout case to trigger the valid
frame done status.
Change-Id: I16a99667116732002e6dec8a18330f8b45199387
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Add vbif axi port halt request support before
MDSS core GDSC power collapse state. It is needed
for targets without MDSS RSC support.
Change-Id: I1fbf281c4206ecd4ad1c2d1348a95e002740e2f1
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
This snapshot includes updates to offline rotator and supporting
files. Snapshot was taken from msm-4.14 as of commit 0f8fb25421ff
("cnss2: Add device version to SOC info structure").
Change-Id: I58674ba880de3d8722ed9119bfc2bee34b444917
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
