Add support for all 4LM topologies in new DCE encoder framework.
This change also aligns with the new way of checking topology
information.
Change-Id: I20785c96569fd07cbd8016d244a7e4c929bfa071
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
From Lahaina onwards, widebus is enabled for compressed DSI stream.
This change adjusts interface timing parameters to account for widebus.
Change-Id: Ie6b739ed2cdb515064e3a94404b3e0fe07755d7e
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
This change adds helper to retrieve the kms from
the drm_enc structure and provides additional error
checking which can be avoided in the callers.
Change-Id: Id8ba07a2d48a605dd4ce846e5d61f302e5861b4d
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
Submit a cwb frame event signal to notify the crtc that cwb
is completed. Currently cwb also uses the same frame done
event as primary. When a single cwb commit is completed, because
cwb is on a slower path there is a race condition in which the
subsequent frame done event for primary clears the refcount.
This fix isolates the events and removes this situation.
Change-Id: Ic3e18302eb8a497cbd7a00f271de2ab320576c83
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Reset MDP ctl path and DSI ctl on autorefresh
disable failure. This will enable the hardware
to recover from the hang.
Change-Id: Ia9acc8573c22e0713179ef4f6ef604caacabfadb
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Add support to configure the DPU pipeline to support VDC-m
topologies.
Change-Id: Ib8ce9a0eaeaa838759fb09cb2ee164d4765e4989
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Certain DSC hw blocks only support 444 mode, while others
support both 444 and 422 modes. This change adds support in
resource manager to check the hw resource requirement with
the capability of the block and then reserve the correct
hw resource.
Change-Id: If85beb2f2f25e9eb7f8a8321c94b57878d048369
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
This change moves the DSC implementation into a separate file.
This is required to add support for new compression algorithms.
This cleanup change also, moves struct sde_encoder_virt
declaration to the encoder header file.
Change-Id: Idc3b96e65fcce2a7ee6e17af604cec0cb574f6f7
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
In dual display cases when secondary display is resumed first,
primary CTL and LM is selected for secondary path which leads to
invalid configuration. Changes are made to correct the reservation
to select primary CTL and LM for primary connector and secondary
LM to secondary connector.
Change-Id: I6b2a8bedaf46f18bdb28b45ac765f32b26207304
Signed-off-by: Jayaprakash <jmadiset@codeaurora.org>
During SUI validations and transitions, the encoders
are iterated to find the panel-mode. If concurrent
writeback is enabled, it is assumed as video mode.
Add check to consider only the built-in display
panel mode during sui to avoid wrong interpretation.
Change-Id: I2901eb29a0799571a95f6ab6f9f3f2c6154424c5
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Primary and secondary displays should have first priority
when reserving lms. Static reservation can potentially block
higher resolutions for the required displays. This patch gets
the layer mixer requirement for primary or secondary display
if available. It reserves those layer mixers dynamically
for the respective display when connector is registered.
Change-Id: Id69dac4c72d6b20008049f4aeb71c0f97d0a426b
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
SDE driver triggers the frame and waits for the
ctl_start interrupt for command mode display. This interrupt
provides confirmation that hardware has picked up the
frame. Retire fence signaling is associated with
this interrupt and it is sent at the rd_ptr interrupt
after ctl_start. Due to lut dma delay, ctl_start interrupt
may be trigger before rd_ptr or after rd_ptr. SW manages
this complexity and handle retire fence for different cases
with 500us threshold logic.
This change replaces the ctl_start interrupt with wr_ptr
interrupt by programming it to trigger at 1st write line
count. This is guaranteed to come every time and it is close
to rd_ptr interrupt. That allows retire fence trigger at
wr_ptr interrupt and simplifies the SW logic. CRTC commit
thread would be held slightly longer with this change
as the wr_ptr is always close to rd_ptr and after
ctl_start.
Change-Id: Ic47a8f82c854b4aded0d70c95af853b28a68ffd6
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This snapshot ports changes from 4.14 to 4.19 into
the msm and sde layer. Snapshot was taken as of
commit 0f8fb25421ff ("cnss2: Add device version to
SOC info structure").
Change-Id: I59b799a78319c2db6930a2a10bc38976f8c09898
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Each mode_set call makes sure that previous frame is triggered
and triggers the esd check if there is pp_timeout. This may
lead to deadlock between crtc commit and event threads. Crtc
commit thread acquires the rc_lock and triggers the flush_thread
API on event_thread. Event thread again tries to acquire the
rc_lock to wait for frame. This can be prevented by avoiding the
pre_kickoff call from esd_failure notification if it is generated
through pp_timeout.
Change-Id: I561fef0345976ab0cae61aab6718214c47fa1393
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Log ping-pong current line count during ctl-start
and rd-ptr interrupt. This will help in debugging
ping-pong timeout issues.
Change-Id: I58185330fe9e8a64f48d6da60c974b23a9e68b44
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
DSI display may support video mode and command mode both and it may
support transition between these two modes.
This change adds seamless transition between these two modes for DSI
display by avoiding crtc enable/disable and panel power on/off
during modeset.
Change-Id: Id7ddaef7d1f0f7cc7d52283755bad53a246adec6
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
