Add NULL pointer checks, before accessing the controller node.
Change-Id: If24c4fd4352ef5ab7642c817ddaa61a80b725c99
Signed-off-by: Vara Reddy <varar@codeaurora.org>
This change allows dynamic refresh trigger to sw trigger
and mdp intf flush. With this we can make sure that DSI
timing/clock update and mdp intf timings are updated in
one vsync.
Change-Id: Ic807f498e2e47be6dd0f1e11ff1fc0896a8ec758
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Add parsing code for getting the TLMM base address and size
of each GPIO pin register space along with the GPIO pins
used for the specific panel. This list is used to lend
these IO ranges to trusted vm during the trusted UI usecase.
Change-Id: I10429cfa14265d52e898815c6cf94be27daa5677
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
DCS brightness settng can only use HS mode. Add a new
DT property for LP mode choose for DCS brightness setting.
Change-Id: Ibe5867fe344776871eb3a410a8d79d347775f3d4
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
The change allows for configuring a command DMA window during which
the command is triggered. The DMA window must not intersect with the
MDP tear check window. Once the command transfer is successful, the
trigger control needs to reset to the default DMA trigger specified
by the panel.
Change-Id: I5485ca1f8e141ed92dc8c77c2daf579634271022
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
During a dynamic mode switch if the DSI clocks need to be changed,
it would result in a sequence of clock off and on operations. If
this happens after a partial update even though the commands are
sent with an asynchronous wait flag, the clock off forces the commit
thread to wait till the DSI command wait_for_done thread is
scheduled and completed. The change ensures that the clock change is
the first operation that occurs during pre kickoff.
Change-Id: I1b4e765cd0281f1539fc4af309247f3bc0867c1b
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Creates a deep copy of a struct which previously was shallow.
Also adds null checks which prevent segmentation faults.
Change-Id: I9155f632736fdb30e31f28f55ebe92954956a82d
Signed-off-by: Orion Brody <obrody@codeaurora.org>
Add support to read register ranges and IRQ lines that needs
isolation during VM switch in dsi ctrl and dsi phy.
Register for VM resource collection event providing the
callback function.
Change-Id: I5eae4699b0a97ffed438627ccea855c401b3fbeb
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Display in trusted VM works in a handover mode i.e, all
display components need to be initialized by the primary VM
before switching to trusted VM on the usecase boundary.
That makes it a hard requirement for the trusted VM not to
re-program any of the display configuration registers before
it could hand the HW back to the primary VM.
Also, most of the linux framework drivers including pintrl, clocks
are not enabled in the trusted VM.
In order to address the above two limitations and to control the
probe/commit sequences, this change adapts the same path as that
of continuous splash to bypass some of the critical functions
which are identified to be HW intrusive. Based on the DT property
read from SDE handle, dsi drivers will choose to bypass
enable/disable HW state updates when executing in the vm environment.
Change-Id: Ica71c924d189ab65fe3be5b0ac870633e3b749e1
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change implements a new feature to read the cmds response
of the panel from sde connector interface. Sde connector opens
debugfs interface for all the connectors those have support for
cmd receive operation.
Sde connector init module creates rx_cmd debugfs file at
/<debugfs-root>/dri/0/DSI-1/ for DSI-1 connector.
Format for DSI command transfer:
echo "command bytes" > /<debugfs-root/dri/0/DSI-1/rx_cmd
byte-0: the length of received buffer
byte-1: data-type
byte-2: last command. always 0x01
byte-3: channel number
byte-4: flags. MIPI_DSI_MSG_*, must be set to 0xa
byte-5: 0x00
byte-6 and byte-7: command payload length
byte-8 to byte-[8+payload length]: command payload
Example:
echo "0x01 0x06 0x01 0x00 0x0a 0x00 0x00 0x01 0x0a" > rx_cmd
The command receive operations are allowed only if controller
(ex. DSI controller) is in active state.
Read the value of panel response:
cat /<debugfs-root>/dri/0/DSI-1/rx_cmd
returns the value of this command.
nothing - failure, xx xx - success.
Change-Id: I912b65d606e248c7a886d219f4363bf7766ee7b6
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
The change allows for multiple TE checks during a pp done timeout.
With this change, when a timeout occurs the panel status is checked
using the default ESD check status method followed by multiple TE checks.
Change-Id: If813964bab55c5e8113721060aa5b279f30fa5e0
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Allocate DSI/LUTDMA buffers from VRAM when IOMMU is not
available. Add checks in msm_gem to avoid few operations
when aspace is not available due to no IOMMU. Parse the
VRAM size from device tree, when available.
Change-Id: Iedf5749b71c2e772ac5434048520a34705c54b45
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Add debug capability to dump clocks before entering pm suspend.
This will help debug invalid register access when clocks are off
during adversarial test cases.
Change-Id: I80d19b751a3b9a1de0cc64699a21a1852d614ced
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
Primary and secondary dsi displays are built-in displays
and they are supported during all concurrency usecases
without resource allocation failure. DP mode filter
logic should provide supported mode information based
on free mdp resources after dsi resource assignment.
Change-Id: I3a9637a91ea1ffcc31997e25caff7f13605283ac
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Lots of dsi FIFO error logs were printed into serial in
dsi ISR. It will make device stuck or deadlock. Remove
these logs from dsi ISR, and enable the log in FIFO error
workqueue handler.
Change-Id: I0e9b2312cb76d345ec5a9b9628c52b47d5163fde
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
If the command line timing is given, select corresponding
drm display mode as preferred mode. Select first sub mode of
that timing as preferred mode if dynamic clock or dynamic fps
is enabled.
Change-Id: I688b3bc07f79f4d014b8a7797204d3d6a873222d
Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org>
Add support to read cphy boolean flag from panel dtsi
and configure DSI PHY registers accordingly. Update the
bit/byte clock calculation according to cphy specifications.
Update clock parents so that the relevant divider blocks
are configured to support cphy.
Change-Id: Iaca61eec01a488657b086f59910c52f8c79e26a4
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
In order to make dsi panel and dsi2hdmi panel compatible,
delete "qcom,panel-force-clock-lane-hs" property in phy and
use display panel's force_clk_lane_hs property.
Change-Id: I490e08b2ee859797c2b3aeddf109a3a4286fb922
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add DSI api to control the connection status of the
DSI interface. This would be used in the VM usecase,
where the connection would be enabled/disabled during
device assign/unassign while switching to the VM.
Change-Id: Ifff41244824ade7a6b8dca77651d82fd5207f8e0
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Make msm_drm into single module and all child driver
registers and unregisters are handled from parent's
register and unregister respectively.
Change-Id: I017513d1de3b6b25dd5543d7fa7741c0bac1740d
Signed-off-by: Shashank Babu Chinta Venkata <sbchin@codeaurora.org>
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Add vote for panel regulators in dsi probe to make sure
panel regulators are ON until dsi bind is completed
for cont-splash enabled usecase. Remove this panel regulator
vote when dsi component bind is done.
Change-Id: I0b1d43fa1b16385712abc1d8aaa0e778f31ba634
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
VFP or HFP is adjusted to achieve constant fps during dynamic
DSI clock switch. This feature is not supported for command
mode. So, add check to skip porch calculation for command mode.
Change-Id: I5fa76d6536a55b2a19f24c0e14b6861e1f4c8f25
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change updates the parsing of timing nodes to check
the mode of operation as video or command. In command mode,
for each timing node, num of supported dfps rate is always
one. Accordingly, update the num_dfps_rate to 1 for
command mode.
Change-Id: I5098c7e0d4d2320609d6e10031eaef78c1d8b3c1
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add support to allow creation of debugfs node only if
CONFIG_DEBUG_FS is enabled.
Change-Id: I1ae2c4188a99e3ed88f59fc021efc01407bf942d
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Optimize pre mode switch panel command by transferring async. This
removes the time waited until subsequent dma_done irq.
Change-Id: I2e2516fdd641e85d1f1b221a6ea7999c868edf00
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change fixes the usecase where dsi msg flags validated only
during command transfer. This fix maintains the flags between
transfer and trigger calls. It also adds a new async override
flag to be used to bypass validate function.
Change-Id: Ie12acd3d7b01099bba65ca37cec61091408b81c5
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
While running the panel in simulation mode using sim-swte, ESD check is
invalid. The change doesn't set the ESD capabilities if watchdog timer
is being used for TE.
Change-Id: I375f369ad4602f21da6151e526e7b6e78fcea524
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
From Lahaina onwards, for compressed DSI output, widebus should be enabled.
In widebus mode, 6 bytes of data are transmitted per pclk.
For uncompressed output, widebus must be disabled to transmit 3 bytes
of uncompressed data per pclk.
Change-Id: I7fc0bdb2e1678152d57b4cbb8295063a2ba8ae73
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
If DPU hardware supports demura feature, install the connector
properties related to demura feature.
Change-Id: Ieaddfc695e9f57e3c45e2bc0bd2c2e103f895ba8
Signed-off-by: Gopikrishnaiah Anandan <agopik@codeaurora.org>
For command mode panels, if a dynamic mode switch occurs on
the first frame, the current code skips DSI controller initialization
and registering for error handlers. This causes the software state
to be uninitialized for DSI CTRL, resulting in command transfer
failures and eventual crash. The change ensures that initialization
is complete even if the DMS occurs on first frame.
Change-Id: I83e3336f7c09424b6c7b95826c30b37974ec29ab
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add this change to ensure that DFPS and RFI happen in the
same panel mode for avoiding unexpected panel mode switch.
Change-Id: I6783b320e73a88e8f75cb83bcce85e50f798b6ab
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Avoid esd check during pm_suspend state because core
clock enable will fail. This change adds additional
check and also adds the clock enable failure check.
Change-Id: Ie8bfa4f74d323ff15a07fb037675f07ab942f016
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
For constant fps feature, porch is calculated based on supported
clk rates. Currently, data type of local variables used for porch
calculation is u32 which leads to incorrect porch calculation for
higher clk rates. So, update the data type to u64.
Change-Id: I8eb04487d1dcce05989448c0b063e56752af412b
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
There is lag or lead in the FPS during dynamic clock change,
along with the increment or decrement in clock. So, HFP or
VFP are adjusted to ensure a constant FPS.
Change-Id: I87ba7a185104a0f5f1d13734a7e487e728d6b2c0
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
DSI host vsync is expected to align with panel internal vsync
during transition from command mode to video mode operation.
In order to facilitate this, keep panel TE enabled in video mode
operation until it is aligned with vysnc.
Change-Id: I3fc59b01336b30cd436be332af6953c5a01be7fd
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
Change fixes parsing of software TE tag added to the display
name from bootloader.
Change-Id: I4747cc6eff43d681477150d6cad7a737963bf11c
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change fixes issues which causes corruption for dual dsi
dsc panel. It fixes the number of slices configured on
dsc hw block and handles deriving correct picture width from
mode timings. Additionally it fixes the core max buffer sizes
used by the hw block.
Change-Id: Iec0ef80528425ffcb5f29d469bd181eb7040de16
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
