On kailua onwards USB3 DP SSPHY power is control using GDSC.
This change adds support to vote for GDSC when displayport
driver is active.
Change-Id: I2e741f2091018f5dae9a1e7e886179bc6b982d40
Signed-off-by: Vara Reddy <quic_varar@quicinc.com>
Decouple the configuration and parsing of aux switches with the
parsing and configuration of HPD sources. HPD notification can come from
either GPIO based approach or a PD module through a SW interface. The
presence of AUX switch on the board should have no bearing in deciding
which configuration for HPD detection is used. Update the implementation
to allow for flexibility in selecting any combination of the HPD source
and aux switches.
Change-Id: I96d558f1d88a359d523fae6dc746045393884d5a
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
Signed-off-by: Rajkumar Subbiah <quic_rsubbia@quicinc.com>
Signed-off-by: Sandeep Gangadharaiah <quic_sandgang@quicinc.com>
pm_runtime_get_sync increases the usage_count refcount immaterial of
success/failure of the call, leading to invalid refcount on failures.
Use pm_runtime_resume_and_get instead, which takes care of reducing the
refcount on failure cases before returning from the function.
Change-Id: Ib96050d5d7ecbd717e58b8a0dde2d03312444e15
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
When switching between 2 dongles/adapters it is possible
to have the same resolution with different link configuration.
Even though the pixel clock could be the same on replug, the
vco clock could be different depending on the link
configuration. Since the dp driver only exposes limited clocks
to the clock framework, in this specific scenario, the clock
driver is unable to recognize the change in source clock rate
and ends up skipping the clock reconfiguration.
This change adds support to park the pixel clocks on disable,
thereby forcing a reconfiguration on subsequent replug even
if the pixel clocks are the same.
Change-Id: If90b37d6285f6cad23cf1c11a7d6ccd6b4cf850c
Signed-off-by: Rajkumar Subbiah <quic_rsubbia@quicinc.com>
Add safety checks to check for dp link and core clocks before accessing
the main control registers during dp teardown or dp setup.
Change-Id: Ic80050b7c1cec59d7fc27a1c5f12fa1b244f86fb
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Check for pixel1 rcg only for mst supported platforms. On sst only
devices bind gets failed.
Change-Id: I73cc4a572d4d0791205c342f57618b226eb91fef
Signed-off-by: Rajat Gupta <rajatgu@codeaurora.org>
Fix dlkm compilation errors that are due to the use of -Werror
flags used by the build system.
Change-Id: I5e1e9bc63c1361d73e4930aab123212717872ecb
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
This change adds the support to request the dp link clk rate
through the mmrm driver. In the case the system can not
support the rate, user space is notified of the failure and
dp is diconnected.
Change-Id: I4a074054ce42425ca940d4aec505723724736b44
Signed-off-by: Christina Oliveira <coliveir@codeaurora.org>
This change sets the regulator voltage to zero for all
those regulators which support voltage scaling before
disabling the regulator. Failing to do so causes the regulator
vote to set to the last min value specified in the previous
set voltage call.
Additionally modified the config regulator api and renamed to
get regulator because of the above change.
Change-Id: Ie4c4842db0c08a4d98926ed79503cf84e4d5762a
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
Add support for PLL programming in the DisplayPort driver.
Change-Id: I4f08a621dcae5d1f54d67bb5c34409249012cc7b
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Adding prefixes for error, debug and info
messages in dp files. To enable debug logs
run "echo 0x100 > /sys/module/drm/parameters/debug"
CRs-Fixed: 2493739
Change-Id: Ibf509e837f527be6bff6b7a1c34b0cde2921b388
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add runtime_pm ops support in drm driver instead
of direct sde_power_resource_enable/disable call.
It allows drm driver to use runtime pm refcount logic
to track the resources instead of custom implementation.
The change also removes the NRT_CLIENT support from
sde_power_handle code to simplify it further.
Change-Id: Ib14692dca5876703d0a230da2512d731b69b8ebb
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
