Add doppler and spatial reuse in ppdu descriptor to be able to use it on
HE information for tx capture
Change-Id: Id87a692a89d00c64929624c22c2efc27bc873e43
This attribute enables/disables the host driver to send roam reason
information in the reassoc request to the AP in the same ESS.
Change-Id: Ie2606012c0487936dd0b436f0d6a75d2e115f4b4
CRs-Fixed: 2627261
If cds_dp_open fails during driver load time, cds_close is
called in clean up path. During cds_close, HTC cleanup happens
which makes target->hif_dev = NULL and in send_packet_completion
target->hif_dev is dereferenced without NULL check.
Add NULL check before dereferencing target->hif_dev during
send_packet_completion.
Change-Id: I236a083e194bf1f16d261e6334ac512c4f6bcd94
CRs-Fixed: 2625690
Add HIF changes for supporting the newly added USB bus type
for Genova.
FW team need athdiag tool to operate FW information. Host
driver need to pass the command and result between athdiag
tool and FW.
Change-Id: I6158a9f8c723a797d39beca09a913c7cb9e10025
CRs-Fixed: 2595515
Add change to increase vdev id bitmap size to the number of vdev ids
bitmap as sent by the FW to avoid memory overflow on host.
Change-Id: I92a2ae31cf0079c989b1788afc61e7f3153dc426
CRs-Fixed: 2626887
Maintain a history of the register writes which
have failed. The failure of register write is
determined by reading back the register after
writing a value to that register. If the read
value does not match the value which was written
then it is termed as a failed register write.
Change-Id: Ic3423c2cbd74bf498c0d3dd8ee7ce4231054541a
CRs-Fixed: 2624475
Fix compilation error in reg_country_opclass_freq_check
return false when HOST_OPCLASS is disabled.
Change-Id: Ib03e544311ae0a6c3496711f303ad17d490900ba
CRs-Fixed: 2624546
We are seeing a invalid memory access crash
in the dp_get_pdev_for_mac_id call from
dp_rx_process_invalid_peer, due to invalid mac id passed,
probably due to some stack correction.
We should instead use dp_get_pdev_for_lmac_id from
dp_rx_process_invalid_peer, where for invalid
mac id, we assert.
Change-Id: I0737132b5bbdd2fcbdb714d4643a69184ae3821e
CRs-Fixed: 2618432
There is possibility that DUT receives non-aggr frames
with non-aggr SN during BA setup during BA session
setup. SSN updates when ADDBA req is processed, should
also update REO SSN one more time when ADDBA resp sends
This will let REO to be able to receive frames in BA
session with new SN.
Change-Id: I4791bcd6f1ede90615c883d31426fcdecd50a631
CRs-Fixed: 2623505
Add new attributes for getting the Beacon frame IEs and the
disconnection reason codes through get_sta_info vendor command.
Host driver provides this information in STA mode.
Add new attribute to get assoc request IEs of the disconnected
peer. Host driver provides this information in SAP mode.
The host driver shall give these attributes as a response to the
vendor command QCA_NL80211_VENDOR_SUBCMD_GET_STATION.
Add the below attributes in to be in sync with userspace,
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_FAILURE
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_AVG_RSSI_PER_CHAIN
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY_SUCCEED
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_LAST_PKT_RSSI
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY_EXHAUST
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_TOTAL_FW
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY_FW
QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_RETRY_EXHAUST_FW
Change-Id: If2727ea4ecbb157035c0f4a989a1a936a5bca64c
CRs-Fixed: 2624843
This acts as an event from the host driver to the user space to notify
the driver specific reason for a disconnection. The host driver
initiates the disconnection for various scenarios (beacon miss, Tx
Failures, gateway unreachability, etc.) and the reason codes from
cfg80211_disconnected() do not carry these driver specific reason codes.
Host drivers should trigger this event immediately prior to triggering
cfg80211_disconnected() to allow the user space to correlate the driver
specific reason code with the disconnect indication.
Change-Id: I6337c02a3508c7ce282f0e3e947d7592e8550308
CRs-Fixed: 2624841
Allocate a buffer of size 4096 bytes for each buffer
posted to CE2 source/destination ring.
Change-Id: I0beb1e4e87c19508917e8564b441819031be2065
CRs-Fixed: 2619899
When radar is detected on a channel and the radar parameters are sent to
FW, the Host Wait Timer expires even though the action status is
received from FW. At this point, the VAP state machine sends a
multivdev restart on the target channel, and is in restart progress
substate.
Since the Host Timer expires due to some reason, radar detect event is
posted to vdev state machine, that is currently in restart progress
state and, this causes a target assert and leads to kernel panic.
This issue is solved by the following 2 ways:
1) Start the host wait timer first, and then send the radar found
params to the target.
2) Check if dfs_is_host_wait_running is true, in the Host Wait Timer's
timeout, and only then call the radar_found_action_generic API.
Change-Id: I9b93c7c1822966f7d6bc00c00229849fdb5627d9
CRs-Fixed: 2604173
QCN7605 has 2 set of shadow registers, WCSS block and PCIe block.
As PCIe shadow register are at power domain boundary, enabling
PCIe shadow register for QCN7605.
Also PCIe shadow register falls below 512KB, no need to use register
windowing which is required to get it access from IPA FW
Change-Id: If18d2d0a3f16f492b3c32449695e70c2b9942375
CRs-Fixed: 2623853
"WPA3-SAE Single PMK" is a feature by which STA can
complete SAE roaming to specific group of AP(s) using
single PMK. This is done with the help of advertising
vendor specific SAE single PMK IE in the beacon/probe.
When vendor specific sae single pmk IE (oui 0x00 40 96,
type 0x03) is present in the beacon/probe of AP then the
BSS supports WPA3-SAE roaming using Single PMK.
Add changes in scan module to parse the Vendor specific
SAE single PMK IE and copy it to the scan_entry ie_list.
Change-Id: I5b7096d1360c624ce1c47e56e8cad37adbdda1e3
CRs-Fixed: 2616099
Do not deinit timer if it has expired since expired timers are
automatically removed from timer list. Only deiniit and delete timer
if it is still running and FW response has been received
Change-Id: I0eb839ba152a20d9da37e1249aa0e4c0543eb494
This attribute aims the STA to send the Beacon Report response
with failure reason for the scenarios where the Beacon Report
Request cannot be handled.
Change-Id: I1b57d1c810deee4545c9a3b84b45ab5bd539d9bb
Crs-Fixed: 2622023
For the 6G band, the only valid opclass_table is the global_op_class
as per the current specification. Therefore, if the band is 6G set the
opclass to global_op_class instead of the default us_op_class.
As per specification for chan width 40 MHz, there is no behav limit
for both Low Primary and High Primary channels. Hence, set behav limit
as BIT(BEHAV_NONE) if channel width is 40 MHz.
Change-Id: I534f5b898e10cf21042a117aa71e824a85d73fb3
CRs-Fixed: 2608059
Add code to move enum _ol_ath_param_t out from common DP code
and move it into OL layer
Change-Id: I92fa5f52c581a18449ab42da41ff5f6f1a2bc595
Crs-Fixed: 2560866
Currently the conversion APIs used doesn't take into account
the overloading of channel numbers between 6GHz, 5GHz and 2.4GHz
bands.
Add support to obtain the correct channel number (and auxiliary
information like band and frequency) through the new APIs that
support all three bands.
Change-Id: Ic2c8dfa4cc845d701dfd07df61c9ae1ee3d8bdef
CRs-Fixed: 2610378
Currently the conversion APIs used doesn't take into account
the overloading of channel numbers between 6GHz, 5GHz and 2.4GHz
bands.
Add support to obtain the correct channel number (and auxiliary
information like band and frequency) through the new APIs that
support all three bands.
Change-Id: Ief417f14620bc2fc02d76fea3642b6fbb9615916
CRs-Fixed: 2610378
Currently mesh mode uses channel numbering which is derived
from APIs that don't support 6GHz channels numbering due to the
overloading of 6GHz channels with 2.4GHz and 5GHz.
Add support to obtain the correct channel number (and auxiliary
information like band and frequency) through the new APIs that
support 6GHz.
Change-Id: Ib0b39ebae2a22bd6b2b5d17b9058c3c2100e0d59
CRs-Fixed: 2605229
Packets delivered to FISA via exception err path doesnot have TLVs.
FISA handling requires additional TLVs. dp rx core handling
skips TLVs, save TLV length info in nbuf->cb so that TLVs
are recovered back in FISA.
Change-Id: I53fab2e19abcbf82697ea6f53a4ddf3ea0dd0699
CRs-Fixed: 2620844
Sometimes the register write in windowed region
are not going through, thereby retaining the
previous value, which can be incorrect for a
certain mode of operation for the driver.
This kind of incorrect register values, due to
a register write not succeeding, can lead to
unwanted issues. Also the simple logging of
any such occcurence can be over-written in the
logs, thereby going unnoticed.
Add a HAL level statistics to maintain the
count of such failed register writes.
Change-Id: Ib5e98705c23f0c916cb85f518576663710eb30e0
CRs-Fixed: 2611839
Add support for the following NAN messages in kmsg:-
1. NAN enable status
2. NAN, NDP match events
3. NDP channel info.
etc.
Change-Id: I7f67b67153904b7efe8a708e3f93d069e399395c
CRs-Fixed: 2618433
Currently if peer reference is reused valid flag is not set.
In peer delete function if valid flag is not set, function
returns with out decrementing the ref count and also not
releasing the local id. This leads to local id exhaustion if
back to back peer reuse happens which is common in case of back
to back roaming to same AP. As a result connection to AP fails
due to unavailability of local id. In this change set valid flag
if peer reference is reused.
Change-Id: Ibeccbc4d33aac9e4285b48a4b8abdd2276fd7ede
CRs-Fixed: 2624798
For Disassoc frame, fw send ppdu stats to host with peer_id
of the previous associated client. peer id is valid and peer
structure is NULL making framectrl as zero for disassoc frame.
with the fix frame ctrl are populated before checking for invalid peer.
Change-Id: I5960685a4c90f00a850f4f1fa2b3d883117fb443
There might be a race condition between htc_kick_queues which is sheduled
by RPM resume and hdd_wlan_stop_modules.
Here are detail info:
1. Run time resume is called, which will schedule a work to do the
htc_kick_queues later.
2. hdd_wlan_stop_modules is called at the same time, which will call
htc_destroy to free the HTC_TARGET.
3. the htc_kick_queues will access the HTC_TARGET, but it has been
freed.
Change-Id: I7211a8eef2a2f1924fe91eafec5a4496eea5a507
CRs-Fixed: 2622317
WMI_WLAN_PROFILE commands support for tlv path.
Add WMI profile enable and trigger commands in tlv path
Change-Id: I10f867b181b559b82c097d6a61236f2145549238
Check the max value for max desc extracted from cfg
before using it for actual allocation of tx descs.
Change-Id: I9bd6c88f136870a42596afbf25328965fce959be
CRs-fixed: 2614329
In the current implementaion, if multivdev restart req is not sent
due to error cases, then the multivdev restart timer gets restarted
after every timeout and the vdev sm is stuck in same state.
Add multivdev restart timeout wait counter and assert after the wait
timeout expires.
Change-Id: I12b10fb7d880e7fcf3dd02d1e38397aa2e3aebe7
CRs-Fixed: 2621231
Query the external radar source and if external radars are
available use the external radars in addition to the internal
radars.
Change-Id: I9fe42ecaaf949f8e504c35ecb8cffb3e9e809fd0
CRs-Fixed: 2615278
Break up the 2MB descriptor bank memory allocations for WBM
idle link ring. Use multiple page allocation and populate the
WBM idle link descriptor ring with physical addresses of each
DMA page allocated in the descriptor bank.
This is to ensure that no requests for contiguous memory
allocations are made that might result in allocation failures.
For MCL set the page size to 4KB and leave it to max_alloc_size
cfg ini param for WIN specific code.
Change-Id: Iec30321044827c0174366cc02df25a42d38309e0
CRs-Fixed: 2565817
Add change to reduce log level for the serialization deinit
debug string as part of bootlog cleanup.
Change-Id: Ibf1cf8352df053df0dba6239f503b868a870a04d
CRs-Fixed: 2623638
Currently, wlan driver prints id in hex mode and
fw prints in decimal mode. Unnecessary hex to dec conversion
conversion is required while comparing with fw logs.
Fix is to change driver timestamp log from hex to decimal.
Change-Id: I78f9b7fe0ba590c53ea3e90b982691d91b7453e4
CRs-Fixed: 2620935
This acts as a vendor event and is used to update the information
of a station from the driver to userspace.
Add an attribute for the driver to update the channels scanned in
the last connect/roam attempt.
Change-Id: I3e87292d6ef00c0242cb583183de2b441352c8a5
CRs-Fixed: 2622092
