PATCH[7/7]:
This patch consists following changes:
-Conditionally compile all monitor destination ring related code
Macro used QCA_MONITOR_PKT_SUPPORT
-Add QCA_ENHANCED_STATS_SUPPORT macro to conditionally compile
enhanced stats support
-Use QCA_MCOPY_SUPPORT and QCA_TX_CAPTURE_SUPPORT macros
to conditionally compile MCOPY and Tx capture features
respectively
-Use QCN_IE macro to conditionally compile BPR
feature
-Use QCA_ADVANCE_MON_FILTER_SUPPORT macro to conditionally
compile advance monitor filter feature
-Fix vdev attach issue for special and smart monitor vap
-Fix status ring initialization issue.
Change-Id: I0deaa28a9a54bf34b0f41e6dd510fdd8d4992db2
CRs-Fixed: 2983780
PATCH[6/7]:
This patch consists following changes:
-Move monitor related pdev variables to struct dp_mon_pdev
-Move monitor relted soc variables to struct dp_mon_soc
-Move cookie to monitor link desc va to monitor file
-Add APIs to access monitor related variables
-Add dummy APIs to build without monitor support.
Change-Id: I032a480b1383d061f984cee3ba6b10ac7a0ff350
CRs-Fixed: 2983781
Same WDI subscribe event can be added multiple times to event list
since this is triggered by user control this will result to undefined
behaviour during events handling.
To avoid this add check to detect duplicate entry before adding
to list and reset list elements once removed from list.
Change-Id: Iaf23927f8439d4ac503776b915a8fe8cb6abfec5
CRs-Fixed: 2931068
Fix issue on enabling packet log.
Fix issue on logging CBF pkt in AP/STA mode.
Fix issue on setting data length 4 bytes aligned in pktlog header
, htt stats indication message header and Rx management TLV header.
Add CBF support for pktlog WMI enable command for firmware to enable
CBF receive.
Change-Id: Ib0067f32d7414be96503c4c67846c1312a59586e
Currently cdp ops are given pdev/vdev handle
as its arguments, which is directly accessed
in those APIs. This can cause a race-condition
in access of the respective handles if it has
been deleted in parallel.
Hence as a part of cdp convergence, pass only
the pdev_id/vdev_id which will be used to get the
respective handles, and hence avoiding unwanted
access of the handles if it has been deleted.
Also deleting few ops which stores and retrieves
such handles and adding ops to set/get pdev params.
- txrx_get_psoc_param
- wdi_event_sub
- wdi_event_unsub
Change-Id: Id089d9b6b4737d700d2436e2081291a3741affb5
CRs-Fixed: 2541658
Change set 1 of the ctrl_ops APIs to replace pdev, vdev and peer
dp handles with pdev_id, vdev_id and peer mac address
along with dp soc handle
Change-Id: Iedf6dea2215d3d04b2212c71c8ec8c7328c559e8
1. Enable CE5 and allow it to service
pktlog messages from the firmware.
2. Register full pktlog callback handlers
for handling sw_events and full tx pktlog.
Change-Id: Ifb70ac0993f2402201f88758845f730cf677b1a0
CRs-Fixed: 2388906
Clean up datapath component prints by correcting trace levels for
regularly occurring prints and removing newlines from converged
print APIs since qdf_trace_msh appends them by default.
Change-Id: Ie8fe319fcb737720f7400a165e134b6a18bd15b5
CRs-Fixed: 2243843
Initialize MAC1 along with MAC0. 2.4GHz monitor mode operates on
MAC1 so initialize MAC1 and reap both MAC0 and MAC1.
Change-Id: Id281def37d460b224f5f571893266f193846fd0c
CRs-Fixed: 2176848
Add polling timer to reap monitor status rings
until PPDU end interrupts are enabled.
Change-Id: I742b0df6fd5a369d9664b5c2e09a70916585174b
CRs-Fixed: 2117063
