In function extract_roam_11kv_stats_tlv, the 11kv channels
tlv is read from the roam_neighbor_report_chan_info tlv if the
neighbor_report_channel_count in roam_neighbor_report_info tlv
is greater than 0. But in some cases, firmware sends value
in the roam_neighbor_report_info->neighbor_report_channel_count
but the roam_neighbor_report_chan_info tlv is not present.
Log error and return if
roam_neighbor_report_info->neighbor_report_channel_count is not
0 and roam_neighbor_report_chan_info tlv is null.
Change-Id: I7fa17d3afaf9d7e6736ad96c60bc5013197480f3
CRs-Fixed: 2644308
The FW has updated the wmi command wmi_vdev_adfs_ch_cfg_cmd_fixed_param to
configure the Agile channel to enable the 165MHz channel as an Agile
channel by enabling 2 center frequencies.
For a 160MHz and 80MHz channel, the parameter center_freq1 will be the
center of the respective channels. For the 165MHz channel(restricted 80p80)
the parameter center_freq1 will be the center of the left 80MHz channel
(5690MHz) and the parameter center_freq2 will be the center of the right
80MHz channel (5775MHz)..
Update the ADFS parameters across UMAC, TARGET_IF and WMI layes to
update the Agile channel configuration command.
Change-Id: Ie480af9a6bb8dad87dd783ab06e17b449605b1c9
CRs-Fixed: 2642555
Enhance logs for PNO scan to remove duplicate
or unwanted prints and keep only useful logs to debug.
Change-Id: Ibe24714e925a00933911c801685528849e160480
CRs-Fixed: 2636641
Add support for WMI event to host to process
dynamically selected Muedca values and update
the mgmt frames with the new set of values.
Extract the params and store in Muedca_param
struct from control path, to be used for
updating mgmt frames.
Change-Id: I6cc7756d1a246ff994edef195f6191d280bc5c47
Currently information is printed in multiple lines that
can be represented in single line.
Change-Id: I7f53acaa4cabd1c970b06cdd82e0c462ffcdffe1
CRs-Fixed: 2617812
In the current implementation the wmi cmd flags to enable bcn rate
code n start req are not getting updated as the flag param is passed
to the API by value and not by reference.
Update the API argumets to pass the wmi cmd flag param by reference.
Change-Id: I8bca4ce78ce68f7b0d05af871641a86bf6622607
CRs-Fixed: 2633704
Extend radiotap header to append ACK status and tx retry count
for packets sent to virtual mon interface.
Change-Id: I51037ffd11dfdee49278d43643fb7861a514ee18
CRs-Fixed: 2627710
In a few scenarios, the number of reg rules can be 0. For example,
for a 2Ghz-only radio there are no 5Ghz reg rules. In such cases,
if we try to allocate memory (0 bytes) the allocation function prints
an error message. Also, the allocation is not required. Therefore, avoid
the allocation when the number of rules is zero.
Change-Id: Ic9caf578541970e9cf12cdde181f23762f137db8
CRs-Fixed: 2622109
Add support for the following NAN messages in kmsg:-
1. NAN enable status
2. NAN, NDP match events
3. NDP channel info.
etc.
Change-Id: I7f67b67153904b7efe8a708e3f93d069e399395c
CRs-Fixed: 2618433
WMI_WLAN_PROFILE commands support for tlv path.
Add WMI profile enable and trigger commands in tlv path
Change-Id: I10f867b181b559b82c097d6a61236f2145549238
For restricted 80+80 MHz FR, target team initially added
wmi_service_bw_165mhz_support to indicate the target is capable of
supporting restricted 80+80 MHz.
Later, they have added wmi_service_bw_restricted_80p80_support to indicate
the same. Therefore rename wmi_service_bw_165mhz_support as
wmi_service_bw_restricted_80p80_support.
Change-Id: I12229b5d35911d4c34e63902c09592187d902bed
CRs-Fixed: 2621249
Firmware advertises WMI_SERVICE_ROAM_SCAN_CHANNEL_LIST_TO_HOST_SUPPORT
at the time of initialization, that means host can querry for roam scan
channels list to firmware.
Host driver sends WMI_ROAM_GET_SCAN_CHANNEL_LIST_CMDID to firmware to
querry roam scan channels list and firmware responds with an event
WMI_ROAM_SCAN_CHANNEL_LIST_EVENTID.
Change-Id: I419a0206d7b06b6186d0c333c951bca5206f342f
CRs-Fixed: 2620607
This patch adds the function to extract and parse the wmi events
WMI_VDEV_AUDIO_SYNC_START_STOP_EVENTID and
WMI_VDEV_AUDIO_SYNC_Q_MASTER_SLAVE_OFFSET_EVENTID. These events are
required for ftm time sync feature.
Change-Id: Ib17da82b7a8abfcff5d18125a0ba0e5249d6bf54
CRs-Fixed: 2615452
A service bit is added to indicate Firmware supports sending NSS ratio
information to Host and Host receives the NSS ratio information from
Firmware as part of service ready ext event. Save this service bit in
soc's extcap feature bit. Extract the NSS ratio info from service ready
ext event and save the results in wlan_psoc_host_mac_phy_caps structure
to calculate NSS value.
Change-Id: I8fbee48d872b0724bbb629ad38b3c959736a3c39
CRs-Fixed: 2612959
Firmware advertises service capability bit
WMI_SERVICE_PEER_DELETE_NO_PEER_FLUSH_TIDS_CMD
when peer delete command takes care of flush
all tids functionality.
If this service bit is set advertised by FW
then host does not need to send the flush tid
command before sending the peer delete command.
Change-Id: Ic6632772eeebc7f1494f1dd5e9d533b2bc22e533
CRs-Fixed: 2609962
Update value of new ini for separate iface support for NAN
"nan_separate_iface_support" to fw through a command
WMI_INIT_CMDID.
Change-Id: I55830e0d16d86ee5a0bfa7d3e44c6309c0d3d54b
CRs-Fixed: 2612010
Currently, the driver rejects the roam stats event if any of the
roam trigger or roam scan or roam results tlv is not present.
Now the firmware will send neighbor report immediately after the
neighbor report response is received from AP instead of buffering
it as done before.
So do not parse the roam trigger, roam scan, roam result tlv if
the tlv is not present. Add new flag in the tlv parsing structure
if the TLV is not present.
Change-Id: I366d8853f7f45dcdac6d4aa5c3a8a12a8b602a4f
CRs-Fixed: 2610377
As part of new requirement WLAN subsystem needs to perform thermal
mitigation action as per the thermal state of the device. The
wifi hal sends vendor command QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD
with the thermal level parameter and wlan host performs the required
appropriate action. wlan host driver maps the thermal level to
corresponding duty cycle off percent value and duty cycle value,
send WMI_THERM_THROT_SET_CONF_CMDID cmd to FW.
Make changes to perform vendor command handling, mapping thermal level
to duty cycle value and communicating the thermal information to FW.
Change-Id: I5b455ae6483f3d5bf2fe708f40c32a55eb8b9bdb
CRs-Fixed: 2610404
This patch adds the support for forming tlv commands
WMI_AUDIO_SYNC_TRIGGER_CMDID and WMI_AUDIO_SYNC_QTIMER_CMDID.
CRs-Fixed: 2607605
Change-Id: Ifaf2b43b60cf604d79d5649b27632422850a0d61
Add support to fallback the PMKID generation from firmware to
wpa_supplicant.
Firmware fallbacks PMKID generation to host when FIPS enabled
due to the crypto library availability limitation.
Once the roam candidate selection is done in the firmware, it
sends the WMI_ROAM_PMKID_REQUEST_EVENTID. Once this event is
received, the host driver triggers an event to wpa_supplicant
for PMKID generation.
Change-Id: Ica00d27ce3f9f4a8f966261b38e238c389fcf05c
CRs-Fixed: 2507617
Avoid direct fw headers usage in init_deinit component since
can have functional impacts. The inclusion is done at wmi level
to fix the inconsistency of code.
Change-Id: I73cc1aac500cec041de81750b9c7654d21344e6c
CRs-Fixed: 2505399
For Genoa, the WLAN FW enables IPA by default, if the
IPA is disabled by kernel config, the IPA status is
not same between wlanhost driver and WLAN FW. So add
such info in the first WMI command to let WLAN FW knows
the IPA state from host, and do the according copy engine
initialization, otherwise, the mismatch IPA copy engine
configuration will casue the Genoa FW assert.
Change-Id: Iec2f86ffb40b296c51bee41adc0d895beb200e5c
SAP not advertising 20TU probe response when
FILS Discovery is disbaled through ini.
Updated WMI fields to enable 20TU probe response
when 6Ghz SAP is operating.
Change-Id: Idc4b95047d2149f68a68a434afda4d325a5d0547
CRs-Fixed: 2600485
Add WMI change to support extraction of consolidated multi vdev
response handling from TLV.
Change-Id: Ida4c346870c99cf5df17b664c4233963585e36cd
CRs-Fixed: 2600388
Firmware advertises service capability bit NAN_VDEV_SUPPORT for
separate NAN vdev creation. This capability can be used to create
separate interface for NAN discovery and process corresponding
commands from userspace.
Change-Id: I4f81b354433c34e8bfe264f69e4eeaf6670f2fac
CRs-Fixed: 2592016
CFR config is passed on to FW through WMI
CFR feature code is moved into feature specific WMI file.
Change-Id: I00b57ea2ef4ec5520eb565910ac2c0a6478170e3
CRs-Fixed: 2582846
In regulatory non-offloads feature, send conformance_test_limit_2G,
conformance_test_limit_5G, reg_domain, reg_domain_2G and reg_domain_5G
information to firmware using WMI_PDEV_SET_REGDOMAIN_CMDID.
If all these attributes are not populated then CTL power limit is
not applied by the firmware.
Change-Id: I1523ab447aec64ec0af42da32318136f90fd17ca
CRs-Fixed: 2518246
Add peer assoc parameter for 6GHz Band Capabilities information
for the corresponding FW peer assoc parameter.
Change-Id: I3bc4361e449843cf73db8426d3bd97dbcd9903ed
