* quic/display-kernel.lnx.5.10:
disp: msm: sde: avoid error during fal10_veto override enablement
disp: msm: update copyright description
disp: msm: sde: configure dest_scaler op_mode for two independent displays
disp: msm: dp: updated copyright set for 4nm target
Revert "disp: msm: sde: consider max of actual and default prefill lines"
disp: msm: sde: Reset backlight scale when HWC is stopped
disp: msm: dp: avoid duplicate read of link status
disp: msm: dsi: update vreg_ctrl settings for cape
disp: msm: fail commit if drm_gem_obj was found attached to a sec CB
disp: msm: dp: updated register values for 4nm target
disp: msm: sde: update framedata event handling
disp: msm: dsi: Add new phy comaptible string for cape
disp: msm: sde: software override for fal10 in cwb enable
disp: msm: update cleanup during bind failure in msm_drm_component_init
disp: msm: sde: dump user input_fence info on spec fence timeout
disp: msm: sde: add null pointer check for encoder current master
disp: msm: dsi: enable DMA start window scheduling for broadcast commands
disp: msm: sde: avoid alignment checks for linear formats
disp: msm: reset thread priority work on every new run
disp: msm: sde: send power on event for cont. splash
disp: msm: sde: always set CTL_x_UIDLE_ACTIVE register to "1"
disp: msm: use vzalloc for large allocations
disp: msm: sde: Add support to limit DSC size to 10k
disp: msm: sde: add tx wait during DMS for sim panel
disp: msm: dsi: add check for any queued DSI CMDs before clock force update
disp: msm: sde: correct pp block allocation during dcwb dither programming
disp: msm: sde: avoid setting of max vblank count
disp: msm: sde: add cached lut flag in sde plane
disp: msm: sde: avoid use after free in msm_lastclose
disp: msm: sde: update TEAR_SYNC_WRCOUNT register before vsync counter
disp: msm: dsi: Support uncompressed rgb101010 format
disp: msm: sde: update idle_pc_enabled flag for all encoders
disp: msm: sde: flush esd work before disabling the encoder
disp: msm: sde: allow qsync update along with modeset
disp: msm: dp: avoid dp sw reset on disconnect path
disp: msm: sde: consider max of actual and default prefill lines
disp: msm: ensure vbif debugbus not in use is disabled
disp: msm: sde: update cached encoder mask if required
disp: msm: sde: while timing engine enabling poll for active region
disp: msm: enable cache flag for dumb buffer
disp: msm: sde: disable ot limit for cwb
disp: msm: sde: avoid race condition at vm release
disp: msm: dsi: set qsync min fps list length to zero
disp: msm: sde: reset mixers in crtc when ctl datapath switches
disp: msm: sde: update vm state atomic check for non-primary usecases
disp: msm: sde: reset CTL_UIDLE_ACTIVE register only if uidle is disabled
Change-Id: If480e7f33743eb4788549f853ba05e744ecb38d3
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
Cape uses phy version 4.3 but requires programming of
different values for vreg_ctrl_0 and vreg_ctrl_1 to
configure LDO setting. Add new phy compatible string
to distinguish cape from other chipsets and program
the registers accordingly.
Change-Id: I68b266cc6e179d211ee0fd05584a605f39b4d31d
Signed-off-by: Srihitha Tangudu <quic_tangudu@quicinc.com>
Add dsi ctrl version 2.7 and dsi phy version 5.2 support for
Kalama hardware.
Change-Id: Ia7b4c8a2e1579458f114e466de8b24855e9251ce
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
In split link usecase with single DSI and dual sublink, the
pixel clock rate should be calculated based on effective lanes
rather than cumulative lanes on that DSI PHY. This effective lanes
can be expressed as number of lanes being used per sublink.
Change-Id: Ia534e816cc64b62c5fe0b9fcaabb9ba52d05bab0
Signed-off-by: Shashank Babu Chinta Venkata <sbchin@codeaurora.org>
Clock lane can enter ino ULPS mode only in DPHY mode. For
CPHY, did not need to check the clock lane status for ULPS.
Change-Id: Iceddd8064ec75ce26613469cfb1bde36e883f865
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
Removes files and version checks for unsupported DSI PHY versions.
Change-Id: I47223a3860e3bcf48eb3b74e405064d8eb375f16
Signed-off-by: Michael Ru <mru@codeaurora.org>
In dumping display registers, physical address will be appended after
each block name. This is to support register compare between kernel
and UEFI.
Change-Id: Ic20d3e2bd4c95aa7c71c4b646a149f7e83ad731a
Signed-off-by: Yu Wu <zwy@codeaurora.org>
The change adds a check for DSI controller and PHY resources during the
DSI display probe. The validation now only checks for the availabilty
of the resources without increasing the refcount of the controller or
PHY till an exact match is found after the device tree is parsed.
Change-Id: I96a5022a8ab5f55271e0df36675037b597e1ec85
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Currently, SDE_DBG_DUMP takes any number of hw block names along with
few defined strings as arguments. This set of arguments is used to
determine which HW block registers needs to be dumped. Move to a
blk bitmask to avoid passing a large set of arguments. The bitmask is
split based on the clks required to access the HW block for ease of use.
The lower 0-23 bits are used for HW blocks which can be accessed by just
enabling the MDP clks. DP is kept separate as it needs DP specific
clks to be enabled. Add a debugfs node through which the mask can be
modified, which can be useful while using the debugfs dump option to
force a panic.
As part of the change, remove in-log/in-mem enable mask debugfs node
for every debugbus and use a single node to control the logging
mechanism for all the HW blocks debugbus.
Change-Id: Ibb6354b3e3265c9911104bb0f964616eb8a898c9
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
PLL codes from devicetree are only required if dynamic clock is enabled
for video mode panels. This change ensures that unnecessary error logs are
not seen for all other panels, by parsing the data only if the panel property
is set.
Change-Id: I206520aab65b7a5613909c8ff527e88303533617
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Change adds the new compatible version strings for DSI PHY and DSI CTRL
for waipio.
Change-Id: I1073034e608cace9d41cc04a9854f15f56828dfe
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Change avoids clock framework APIs to configure the DSI PHY
PLL. It follows HW recommendation to set the byte and pclk
dividers.
Change-Id: I8c110f3997e4ec4c2eaa28778b70091855725ab8
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change allows dynamic refresh trigger to sw trigger
and mdp intf flush. With this we can make sure that DSI
timing/clock update and mdp intf timings are updated in
one vsync.
Change-Id: Ic807f498e2e47be6dd0f1e11ff1fc0896a8ec758
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Add support to read register ranges and IRQ lines that needs
isolation during VM switch in dsi ctrl and dsi phy.
Register for VM resource collection event providing the
callback function.
Change-Id: I5eae4699b0a97ffed438627ccea855c401b3fbeb
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Display in trusted VM works in a handover mode i.e, all
display components need to be initialized by the primary VM
before switching to trusted VM on the usecase boundary.
That makes it a hard requirement for the trusted VM not to
re-program any of the display configuration registers before
it could hand the HW back to the primary VM.
Also, most of the linux framework drivers including pintrl, clocks
are not enabled in the trusted VM.
In order to address the above two limitations and to control the
probe/commit sequences, this change adapts the same path as that
of continuous splash to bypass some of the critical functions
which are identified to be HW intrusive. Based on the DT property
read from SDE handle, dsi drivers will choose to bypass
enable/disable HW state updates when executing in the vm environment.
Change-Id: Ica71c924d189ab65fe3be5b0ac870633e3b749e1
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
In order to make dsi panel and dsi2hdmi panel compatible,
delete "qcom,panel-force-clock-lane-hs" property in phy and
use display panel's force_clk_lane_hs property.
Change-Id: I490e08b2ee859797c2b3aeddf109a3a4286fb922
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
DSI PLL is tightly coupled with DSI PHY. This change removes
separate DSI pll driver and makes DSI pll as a subnode to DSI
PHY which is an accurate way of representation. In addition, this
change adds support for 5nm DSI ctrl and PHY revisions and adds
DSI pll support for 5nm. Remove support for older DSI pll revisions
such as 7nm, 10nm, 14nm, 20nm, 28nm.
Change-Id: Ic8b886a9fe24b906e4ec5130720600efa1e59b68
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
DSI driver did not use msm bus scaling setting,
remove the code.
Change-Id: I71675c8f4e3e97f1ded72ecac3fa87bdc7fb3774
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
DSI PHY timings must be committed every time the values
are updated after a dynamic mode switch.
Change-Id: Id605c76dfe75ec41ceb89000f24baccda189e82f
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Adding debug, info and error prefix for log messages
in dsi files. To enable debug logs
run "echo 0x1 > /sys/module/drm/parameters/debug"
Change-Id: I438ac16954bd1d39450f8adeb7fb17f9ea6f8140
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change is a snapshot of dsi files taken of 4.14
as of commit 764f7c2 (Merge remote-tracking branch
'quic/dev/msm-4.14-display' into msm-4.14)
Change-Id: I8361a844c35a4450f7800964a8da2741676fd6c7
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change adds support for dynamic switching of dsi clocks
to avoid RF interference issues. Also with dynamic dsi clock
switch feature coming into picture, now populate the supported
refresh rate as list instead of providing a range. Modify the
logic to enumerate all the modes in dsi driver, taking dynamic
bit clocks, resolutions and refresh rates into account.
Change-Id: I5b6e62bc935cf2234bdd96fcb3c7537b4e735fff
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Yujun Zhang <yujunzhang@codeaurora.org>
Remove the redundant register dump sub range
registration for DSI ctl/phy as it needs only
the base registration, since it is considered
as a single block.
Change-Id: I11546bfcde05d02849c53577c4546dcfa9203539
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
