In case if TWT command (i.e setup, terminate, pause, resume,
nudge) comes from userspace and if the firmware is in below mode
1. scan in progress
2. roam in progress
3. CSA is in progress or
4. Any other error
then the command needs to be rejected in userspace context.
Synchronize the TWT command so that whenever command goes from
driver to firmware, then driver will receive ack event first
followed by respective event (i.e add dialog, delete dialog,
pause, resume, nudge) with below condition
1. If driver receives the ack event as successful then driver
waits for this ack event, respective event with status of the
TWT action frame over the air is expected.
2. If driver receives the ack event as failure then it will
rejects the TWT command in userspace context.
Change-Id: Ie885d98ecf2dad98d34676d889fd70e4c84f0a05
CRs-Fixed: 2987904
In MISSION mode, MSI address and data are still
configured for monitor status rings even though MCC
uses only polling mode for this ring.
Fix is to skip MSI configuration for monitor sts
ring in MISSION mode for MCC.
Change-Id: If295a5afc6731bbec1ad7182590e0015f3a911ba
CRs-Fixed: 2992167
Currently host is populating secondary channel list from master
channel list based on ap power type. In case fw doesn't support
extd cc event then secondary channel list will not have 6g freq,
which may break legacy 6g handling.
Fix is to add validation check for ext cc event support, copy
secondary channel list from ap power type in case ext cc event
is supported by fw else copy secondary channel list from reg
current channel list.
Change-Id: I2e13be2936b624ccbee5e8e426987355076a0062
CRs-Fixed: 2987951
skb_set_len and skb_pull operations are done in both
dp_rx_deliver_to_pkt_capture_no_peer and
dp_rx_deliver_to_stack_no_peer. Due to this, in the
issue scenario, EAPOL frame gets dropped in roaming
scenario since qdf_nbuf_is_ipv4_eapol_pkt returns
false.
Fix is to do a skb_push_head operation in
dp_rx_deliver_to_pkt_capture_no_peer API before
exiting.
Change-Id: I071a5248f9f8577c8a21547f67ec53d707dee0be
CRs-Fixed: 2982188
Add TWT service bit capability support to check whether firmware
supports ack event or not. If firmware doesn't support ack event
then service bit capability will become 0 and whenever TWT
command comes, host will not wait for ack event and sends command
in a legacy way.
This support is mainly added to handle new host and old firmware
combination.
Change-Id: I55d373c2e017130b58a4b332da16f0eda8f34eba
CRs-Fixed: 2987749
Add TSF cmd to enable and disable automatic TSF report from the target
to the host.
Change-Id: I17b255299f55b8e78968d951824726d533a7c6e9
CRs-Fixed: 2991909
Allow all raw frames to the upper layer without checking
for port authorisation. All checks in raw mode has to be performed
by the controller in case of raw mode.
Change-Id: Ica6df24b359790fcadc9bb7bbb4d7b5084930170
Add #ifdef around the body of the header file so that multiple
inclusions from the same translation unit does not fail compilation.
Change the type of the frequency variables (lowfreq, highfreq) from
signed to unsigned.
Changed the positions of the 16-bit variables (version_minor,
version_major) to avoid alignment error (8 Byte alignement).
Change-Id: I72b8f7acbf21a249e2380301b41739cbe06345d6
CRs-Fixed: 2988464
Include afc common service header file to fix compilation error for
spectral module files.
Change-Id: I14d6bdb6437cb3eea3b85a72dcb3a9760186cc4b
CRs-Fixed: 2988464
Add API to extract AoA phase delta and IbfCalValues from
WMI event. Also Add service bit to support the feature
Change-Id: I6f6514711345dd47c4be3673b8c40501feb763e9
Currently, excess logging is causing a crash when there is no
data to reap.
Rate limiting the log messages to avoid the crash due to excessive
logging in case of no data to reap.
Change-Id: I175f3f1b3c0b0173f171e971494f6ffda694b4a5
CRs-Fixed: 2988147
Changes to extract AoA phase delta values from WMI event.
The AoA phase delta values along with ibf calibration value
is shared to derive the phase values which is to be used in
CFR.
Change-Id: I70f50656db4194025a0b6b37c8b4a27048968e0f
Changes to derive chain phase values out of Hardware
reported agc gain and target reported AoA phase calibration
values. AoA for RCC to be supported based on target shared
capability. AoA phase delta & ibf cal values are shared by
target upon every channel change via WMI event.
Change-Id: Ic4fca3731b795e07a511388f6dbb15a46d676a77
Spur or leakage transmissions is observed in Spruce HW in
frequencies from 5260MHz to 5320MHz when one of the following
conditions is true,
i) The AP is transmitting in 52/56/60/64 in 80MHz mode and then the AP
moves to the adjacent channel 36/44/48 in 80MHz mode and starts
transmitting.
ii) The AP is transmitting in 36/44/48/52/56/60/64 in 160MHz mode and then
the AP moves to the adjacent channel 36/44/48 in 80MHz mode and starts
transmitting.
In order to prevent random channel selection to cause spur restrict the
above given channel movements for Spruce target alone.
Change-Id: I27b558ec5544076430f66c84b056ab65f9e43c8c
CRs-Fixed: 2975473
In function wlan_dcs_cmd_send(), pointer dcs_tx_ops returned from
function call target_if_dcs_get_tx_ops() may be null and will be
dereferenced, it's an issue to dereference dcs_tx_ops without null
check.
Fix is to add null check for dcs_tx_ops pointer before use in
function wlan_dcs_cmd_send().
Change-Id: If82f31bd8f5096a4e6562131426510907555140d
CRs-Fixed: 2989520
On 5.10 kernel need idle” functionality is moved from
<linux/sched.h> to walt (<Linux/sched/walt.h>), Replace
“PF_WAKE_UP_IDLE” checks with “IS_ENABLED(CONFIG_SCHED_WALT)”.
Change-Id: Icb89b0e6e9862ed5b82680379a1d2630c9b2b4d9
CRs-Fixed: 2990760
Add number of page desc check for TX/RX desc_pool de-initialization,
avoid unexpected assert in case SPT page_desc_list is not
initialized like SSR case.
Change-Id: I970f0e09a0631260e1cb0d1de23a1de3e8d13f24
CRs-Fixed: 2991334
Currently, partner info array in scan entry is contains self link
information in first index. to avoid confusion, update partner info
with only partner links information and store self link id in ml_info
of scan entry
Change-Id: I53992fee355613b8521409da412254c05fb63fbf
CRs-fixed: 2991229
Add QCA vendor attribute QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS
to configure FT over DS to the driver/firmware.
Change-Id: I0745c27c6bc0a8d1075d753f1d898870479105f8
CRs-Fixed: 2968681
Add a separate module ID for Multi Link Operation (MLO) Information
Element protocol processing related QDF trace prints. These are for
use in processing of any IEs related to MLO. This would help separate
the tracing of MLO IE operations which are expected to be substantial,
and avoid confusion that might arise from reuse of MLO manager
tracing.
Change-Id: If55532a89452b6432101be07fcc6aff45045e822
CRs-Fixed: 2985731
Define a new cdp interface structure and API for soc stats for use
by upper layers to fetch dp soc stats.
Change-Id: I314e952546551003da2ca7f69b2e1aa23c126e66
Replace util_scan_scm_chan_to_band with util_scan_scm_freq_to_band
to work for 6G channels.
Change-Id: I5f8843599cbea194a57cc7fc3b20163a7205f4e7
CRs-Fixed: 2987153
-Add validation check for MLD address as part of ML dev context
creation.
-Modify some function descriptions to clearly state the purpose.
Change-Id: Id049145351bdd790126e0ab522d24e4c399c0ad2
CRs-Fixed: 2976130
Changes to derive AoA phase values in RCC mode.
Add AoA phase calibration parameters to pdev_cfr. These
gets filled upon FW WMI event for every channel change.
HW reported AGC gain & these values are used to derive per
chain phase values.
FW to advertise support of this via service flag.
Change-Id: Ie239b939e50c60c5658ed0a82bae3243e5028e77
Check the below service bits and set in psoc if the service is supported
by FW.
WMI_SERVICE_RTT_AP_INITIATOR_STAGGERED_MODE_SUPPORTED
WMI_SERVICE_RTT_AP_INITIATOR_BURSTED_MODE_SUPPORTED
Change-Id: I13504958bf31b2d645d915b4db20719bdc9a4133
CRs-Fixed: 2969195
Add puncturing bitmap along with channel parameters
in vdev structures for filling during vdev start.
Change-Id: I5e5afd6e118ed9933e4d9c30e2ad65cd4259bca0
CRs-Fixed: 2958389
Add scan support for puncturing by extracting the puncturing
bitmap field in the EHT operation IE.
Change-Id: I221464f52bfce40b55344f995945836f80553579
CRs-Fixed: 2982502
Add WMI support for EHT puncturing by filling puncture
bitmap in vdev start and peer assoc commands.
Change-Id: If1d2541655558f22a96a741999ec4ff7348f695a
CRs-Fixed: 2982498
In the current implementation, csa_event_bitmap for CSA in the beacon
template WMI command is set to 0. Hence, the FW sends CSA complete event
to the host at the end of CSA complete.
Set the below values to csa_event_bitmap to get the current channel switch
count from FW to update the CSA/ECSA IE count in probe response frame.
1. WMI_CSA_EVENT_BMAP_ALL:
To get the CSA switch count event for every update to switch count.
2. WMI_CSA_EVENT_BMAP_SWITCH_COUNT_ZERO:
To get the CSA complete event only when the switch count becomes zero.
3. WMI_CSA_EVENT_BMAP_VALID_MASK:
FW to follow the bitmap for sending the CSA switch count event to the
host. Example,
0X80000000: Send the CSA event when the switch count becomes zero.
0X80000033: Send the CSA switch count to host for the count 0,1,4 and 5.
Change-Id: I8380d6badc3b84c72fde489e59b51b5ac122b97b
CRs-Fixed: 2978799
Currently there is no synchronization for flush log completion
between fw and userspace. When host driver receives command to
flush logs, it sends the command to fw and releases the control
of the userspace thread, it does not wait for the flush log
completion event from the fw and because of which user space
does not know when the host and fw completes the log flush.
To address above issue add a logic to wait for fw event of
flush log completion before host returns control to userspace.
Change-Id: I04fa0aead146d2b7b8627e4101c6dcd99d3947e9
CRs-Fixed: 2983387
In the case of Roam Start sub-state, if a new connect/disconnect
is received, an internal disconnect/actual disconnect is queued
in serialization and then the state is changed to connecting
or disconnecting, but if the disconnect command becomes active
directly the EV_DISCONNECT_ACTIVE is received in roam substates
but is not handled.
As EV_DISCONNECT_ACTIVE is not handled the disconnect is not
processed and VDEV can remain in UP state while CM assuming that
the disconnect is completed will allow a new connection which
cause 2nd BSS peer creation.
Fix is to handle EV_DISCONNECT_ACTIVE event in Roam sub-states.
Change-Id: I30180db2e15af9b793e52e891f86d54c55b7b5e0
CRs-Fixed: 2986468
Initialize the last_desc_cleared pointer to -1 not 0, and
also fix the check it should always behind tp.
Change-Id: I281e066d45a99ac99d4f3c4e0bcc3f65f14bb589
CRs-Fixed: 2987029
In Tx monitor code, BSS color needs to be retrieved
from the PPDU TLV so that it matches the value in
transmitted packet.
Change-Id: I6e1dce3992264ebea2db37b2d9c8f156a23df028
Cleanup reg_cache_channel_state and the
related code with it.
Also, changed the logic so as to compare
channel freq instead of channel number in
reg_modify_chan_list_for_cached_channels()
Change-Id: I424b6886ed18f73bae0d2b36e36a9ddc1819688b
CRs-Fixed: 2908016
Modify APIs target_if_dbg_print_samp_msg() and
target_if_dbg_print_samp_param() to use the
new formats for spectral_samp_msg and
target_if_samp_msg_params, respectively.
CRs-Fixed: 2961953
Change-Id: Ib0776c2189e9ca1dc33d38f2a7609aa6d15959ee
