As per current design, dp_mlo_ctxt is allocated during the
initialization of module while the MLO grouping information is
understood after WMI_READY_EVENT. The same is deinitialized while
unregistering the module.
To ensure dp_mlo_ctxt exists per MLO group, bring the dp_handle
a layer below in the hierarchy into the mlo_setup_info and allocate
dp_mlo_ctxt after the WMI_READY_EVENT is received from all the SOCs
for a given group. Deallocate it after the WMI_MLO_TEARDOWN_COMPLETE
event is received.
CRs-Fixed: 3355405
Change-Id: Ic3102a34a8d44877827e2ff1f7da2e414b2b463f
To handle dp_mlo_ctxt assignments from the UMAC module,
moving the callers for attach and detach to the list of
MLO operations for multi chip.
CRs-Fixed: 3355400
Change-Id: Id743ec1086cf1b3ba0a3ec42212dc21c5a9ccc6b
rx user status pointer is not valid
memzero ppdu_info before ppdu TLV processing and
Assign valid user status pointer from ppdu_info
user status before rtap update.
Change-Id: Ib9f8bf356a8d4710d295716cf88b8cf6a37158cb
CRs-Fixed: 3341380
Currently the datapath stats do not print the
packet count for 320 MHz bandwidth.
Add support to print BW counters for 320 MHz.
Change-Id: Ic9579a1860e6aca442f7bc4a3b92930e8506e9bd
CRs-Fixed: 3359372
1. Change the names of parameters and functions related
to direct switch feature from ppe to ppeds
2. Remove the unused ppe_release_ring
Change-Id: I5a95b1273e338f354903af98158578ac65758a8a
CRs-Fixed: 3345097
Issue:
When DS mode is configured for a VAP
in both AP and STA (RDP 433), the tput reduces.
For instance, for an ingress of 7G
in standalone case, the egress rate is
1) 6887 Mbps when DS is enabled only in AP
2) 1900 Mbps when DS is enabled in both AP and STA
RCA:
With the help of debugs & proc/interrupts, identified
that we are not setting up the peer when the
device in STA mode due to AP mode check in
dp_soc_txrx_peer_setup.
Hence, the traffic is not flowing via DS
and so, tput reduces.
Fix:
Added changes to invoke txrx_peer_setup in
STA mode and DS mode will configured in that mode.
With the fix, traffic flows via DS, which
in turn improves the increased
Change-Id: Ib51e9a27e5078ed99160f213ddffed801c2e4ecf
CRs-Fixed: 3355603
Check size of the frag before passing
to trim function, which can lead to memory
corruption.
Change-Id: Icea102f9fef8c7333591337a93d32bc449704202
CRs-Fixed: 3354458
Program service code bypass to avoid
L2 new mac address learning exception
when fdb learning is disabled
Change-Id: I588a885aac1755cdf2ded5176b25d5ae9f533091
CRs-Fixed: 3354407
Requirement:
As part of serviceability for DS, display the number
of Tx descriptors currently in use by DS module
via “cfg80211tool athXX txrx_stats 260” like non-DS.
Snippet of log/code of Non-DS:
DP_PRINT_STATS("Tx Descriptors In Use = %u",
soc->stats.tx.desc_in_use);
Fix:
Introduced a new ops (dp_tx_ppe_ds_inuse_desc)
to display the current Tx desc in use.
dp_ppe_ds_inuse_desc API will be registered
to dp_tx_ppe_ds_inuse_desc in initialization
and it will be invoked from dp_print_soc_tx_stats API
to display the in_use desc via 260 command
Change-Id: I18971fc5d4cb5eb5437b012e3b89db7c9c2446b4
CRs-Fixed: 3352686
In the PPE-DS UL path, the PPE-DS flag is getting set in the buffer
in the EDMA Tx complete path.
This flag is getting checked in the WLAN Rx replenish path and the
data invalidate is being skipped, if the flag is set.
CRs-Fixed: 3344458
Change-Id: I4e10deec5b373ccc93b59432576eb70d49a9304d
Change interrupt timer threshold for ppe2tcl ring to 30 us
from existing default timer threshold.
Change-Id: Id6a2625c086af6c4c49188c0abdc8d24fb8bdfe5
CRs-Fixed: 3355208
1.Add check in Tx completion path to handle
mcast packets from all ML partner vdevs
2.Handle cases where a ML mcast vdev can be
deleted and started as NON-ML vdev and
viceversa by adding reset ML mcast conf.
3.Optimized Register configurations for Mcast
at Init/Delete and Start/Stop AP
Change-Id: Iab8a5a081e2e0377509574d362754d32c5b83df2
CRs-Fixed: 3350350
Suspect HW update WBM2SW ring HP, but the ring entry contents are
not updated accordingly which then host will fetch one stale ring entry,
this makes other TX packet are freed unexpectedlly.
Add change to detect this situation earlier, if HW cookie conversion is
done, then invalidate 2nd dword for upper 32bits of VA, so next time when
reap this ring entry contents to know if this desc is updated by
HW or not. if HW cookie conversion is not done, then compare the PA in
buff_addr_info with PA in current TX desc to check.
Change-Id: I351eb4f860216fc618ff28736d4832fcec45dcc5
CRs-Fixed: 3345935
Adjust low watermark refill for RxMON Source ring based on
ring_fill_level.
ring_fill_level varies based on use case of monitor like
enhanced_stats, full monitor.
CRs-Fixed: 3353181
Change-Id: I4e17eecbbd7f74071283d2c5615904310a3d7c77
Currently HP update can skip for few packets if the system suspend
is happening in parallel with tx. This could lead to SMMU fault if
the skipped HP update goes after tx desc force free.
Remove the tx pause check in HP updates and have the check before
calling dp_tx_send in case of intra-bss forward case. No special
handling is needed for non intra-bss case as we don't expect packets
from network stack after suspend.
Change-Id: Id4f2cefcc0a14e7c16438b9bda5cb1d55eb05050
CRs-Fixed: 3327818
Handle mlo case for ppe ds peer setup by
making sure the src_info is always extracted from
primary vdev.
Change-Id: Ie4b0d8f475966e8c4264cea5cf32f0dc95e76c4a
CRs-Fixed: 3346074
set rx_reo_queue_desc_addr_31_0 and rx_reo_queue_desc_addr_39_32 to 0
in hal_reo_shared_qaddr_write_be
Change-Id: Ib92775e0883b68f49c27e606e762384239bae955
CRs-Fixed: 3339043
Only 8 RX data TIDs are used, so HW stats query only needs to update
these TIDs info to save command executing time.
Change-Id: I04b65d19ddb3a9e43cb96b266708272769f7dcf2
CRs-Fixed: 3348771
Enable and register PPE2TCL and REO2PPE ring interrupts
for direct switch
Set interrupt timer threshold for ppe2tcl ring as 30 us.
Change-Id: Ida1ff6c3c2000f16f07960f7eae0d10edc337dc0
CRs-Fixed: 3341790
Add support for GET MLO Multicast API to check
if the vdev is primary multicast vdev.
Enhanced SET MLO Multicast API to reset primary
multicast flag for all partner vdevs.
Change-Id: Ic88949ce922bb1d0fd34349058d254de0d1f563c
CRs-Fixed: 3322523
Vlan Header is not initialize before passing it
to IPA driver, due to this some Vlan header fields
are junk and causing issue in IPA driver.
Fix is to initialize the header with 0
CRs-Fixed: 3342771
Change-Id: Ic29e0822f32bec5ea71702ceea75b7354caeda65
In the dp_tx_desc_set_ktimestamp() return false case,
tx_desc->timestamp will not be updated, instead,
tx_desc->timestamp_tick used. So it will cause
dp_tx_comp_delay_check() always return false when
timestamp equal zero. Need to move the tx desc
timestamp check to correct place.
Change-Id: Ic1d5f1035784dcc3f240d832ac1e8820bc24f782
CRs-Fixed: 3331251
nbuf could be freed when some error conditions are hit so
always validate nbuf while processing MPDU/MSDU level TLVs.
Change-Id: I5e0756bc8ba0a8c68c6ce8d2886b5b63068626a0
CRs-Fixed: 3318966
If IPA tx alt doorbell address is not returned from IPA, wlan
should not touch the tx alt paddr and vaddr either. Therefore
add the NULL check before handling the tx alt ring resources.
Change-Id: I6b98fe5c003f3e796441513515190ea592d14d01
CRs-Fixed: 3339322
buffer_timestamp in wbm2sw ring descriptor is 19 bits only with
unit 1024 us, so it can only accommodate 0x7FFF * 1024 us same as
29 bits value with unit us. but if the timestamp value is >
0x7FFF * 1024 us, then the value stored in buffer_timestamp is not
right as other higher bits bit29 ~ bit31 is lost.
restore bit29 ~bit31 value for buffer_timestamp to fix current issue.
Change-Id: Ie929f560365cc822883711133541772348775357
CRs-Fixed: 3336241
Currently, in case of station+monitor mode on KIWI target,
we are not attempting to drop the entries received in the
monitor destination ring, when no channel has been
configured for the monitor interface. This leads to the
monitor destination ring full condition and an eventual
backpressure on the ring.
Fix this issue, by dropping the entries in the monitor
destination ring, which have been received before the
monitor channel has been configured.
Change-Id: Ic9c432b438d0a5dce2d2bb38053c31ce508c27f5
CRs-Fixed: 3332327
Only 8 RX data TIDs are used, so HW stats query only needs to update
these TIDs info to save command executing time. Change is aimed to
reduce the TID number and use only one REO flush command for overall
REO cache flush.
Change-Id: Ib642451b9f07f62198126c45644742e1908280cd
CRs-Fixed: 3325964
Change module id to QDF_MODULE_ID_DP_HTT for hexdump printing
of hw vdev stats.
Change-Id: Ie9db76aa04241680236aa6b23a4ee65b5fd89d23
CRs-Fixed: 3343177
When high throughput is running between AP and STA,
due to u8 variable overflow, host is not replenishing
required buffers.
More than 255 buffers can be requested for replenish,
so fixed size of the variable.
Change-Id: Ia810fed29058ec527cd8e6f77e6f9c333c5c6f88
CRs-Fixed: 3306616
Retain ds ring indices across wifi restart to avoid
edma hang. Fetch the indices from ds module and set
the corresponding ds ring indices.
Change-Id: Ia299a7006166aef096c7d2c1f65f6bef65415a37
CRs-Fixed: 3332152
