Currently wifi positioning api to update channel bandwidth
info is invoking regulatory component api to set the channel
params with BW as CH_WIDTH_MAX, because of which regulatory
component is returning the maximum BW supported for the current
regdomain which is 160MHz. If target does not support 160MHz in
that case it may lead to undefined behavior.
To address this issue, pass max supported BW by target as
argument to regulatory component so that regulatory component
does not return the BW greater then the target supported BW.
CRs-Fixed: 2730665
Change-Id: I6051336ab2f3ea902a70ed80290e5a5f060de5b9
For SAP on DFS channel, the PCIe link down should be prevented
so that HalPhy can access DDR memory to report Radar found event.
Change-Id: I5eb1076196c509f0279781dbe3269d62132aeabc
CRs-Fixed: 2712800
Introduce APIs to perform postNOL channel switch to user
configured channel after the NOL expiry of said channel.
This channel change will involve regular CAC after vdev start.
Change-Id: I426b0c4b51c84789870841dd4c3af942be185f20
Following are a part of this change:-
1. Add an API to check if PreCAC/RCAC is enabled. This API is used before
delivering an external event to Agile SM.
2. Post an event to the Agile PreCAC SM if Radar is found on
agile channel. Radar on primary channel is taken care of by the
ensuing channel change.
3. Move all Agile PreCAC changes under macro QCA_SUPPORT_AGILE_DFS,
only RCAC specific changes remain under QCA_SUPPORT_ADFS_RCAC.
Change-Id: I45d4b9f826d36e9e4093879b394165a15a52f324
Both (ETSI) PreCAC and RCAC are going to use use the same state
machine. The state machine drives the Agile engine and not very specific
to RCAC or PreCAC, therefore let the state machine be called agile state
machine and change the names of all the associated variables accordingly.
In this preparatory change, modify names of all APIs, states and events
to make them common to Agile RCAC and Agile PreCAC
Change-Id: I67858839589145bf4377a7eafec7c21ca4823141
CRs-Fixed: 2711104
Support a new capture_interval_mode: capture_count, where after
capture_count+1 number of frames, MAC stops channel capture and
waits for capture_interval duration before enabling again.
Add nob(capture_intervalmode_sel) to switch to capture_count or
capture_duration mode in wlanconfig application, where
capture_intervalmode_sel=0 indicates the old capture_durarion
mode where MAC stops channel capture after capture_duration
instead of capture_count. capture_intervalmode_sel=1 indicates
the capture_count mode.
Support MO marking: Current ENH CFR uses the existing MD/MO,
type/subtype filters to filterin the packets with programmed
type/subtype as either MD/MO. But for m_TARA it is also required
to consider the bw/nss/ta/ra setting. Therefore, it is possible
that not all the filtered-in PPDUs have channel capture and lead
to processing of packets which does not have captured data.
To overcome this issue, from QCN9000 onwards, MAC has MO marking
feature added for M_TARA filter mode, where MAC will consider
all TARA group configuration as filterin criteria & provides
an option to HOST to choose either filterin mode as FP or MO.
en_ta_ra_filter_in_as_fp is added to support MO marking.
Based on the discussion between HOST, FW & MAC teams, 0 is the
recommended & default setting for en_ta_ra_filter_in_as_fp.
Add nob to configure en_ta_ra_filter_in_as_fp but do not expose
to user.
Change-Id: I75cd3218fa4308afad21052e4535ef9b8e5a5869
It starts spectral scan without vdev object, and uses the first vdev
as current vdev. which cause vdev mismatch in some platforms. So pass
vdev object or id when finding current vdev.
Change-Id: Iab55afbe2c98906021a008918f186d3d2dce5871
CRS-Fixed: 2716460
CONFIG_CHAN_NUM_API macro will be disabled. Remove all the references to
any function defined/declared under the macro. The function
reg_get_channel_list_with_power was placed under CHAN_NUM_API by mistake.
This API does not have any CHAN_FREQ_API counterpart. Therefore, move
this function out of CHAN_NUM_API macro.
The function dfs_send_radar_ind_for_freq is redundant as its counterpart
dfs_send_radar_ind has the same arguments and same functionality,
removing the function dfs_send_radar_ind_for_freq. The function
dfs_send_radar_ind is moved out of CHAN_NUM_API macro.
The function wlan_reg_chan_to_freq, wlan_reg_legacy_chan_to_freq is
moved out of CONFIG_CHAN_NUM_API macro. Since it is applicable for legacy
bands.
CRs-Fixed: 2711600
Change-Id: Ib29be638c17ce51f928c865e362ac5b2b8954b42
Add new channel bonding pairs as well as frequency
pairs for 40, 80 and 160 MHz with the support of
three new 5.9 GHz channels 169, 173 and 177.
Add new API reg_modify_chan_list_for_5dot9_ghz_channels
to enable/disable these new channels based on
INI value and service bit.
Change-Id: I8598e705ba4047e96e7167661ba70d4236cde251
CRs-Fixed: 2696211
LOWI application provides the interface name as part of lowi message to
host driver. Add support in the driver code to get the corresponding
pdev_id and pdev from interface name using dev_get_by_name().
Change-Id: I267b95c843a9bb1dd0c58ff45767f31999500b1c
CRs-Fixed: 2711423
Adding support for iot_sim drop operation.
Drop operation will be handled in Rx direction.
Change-Id: If2e1c9663a69fcd16715cdd1d28639a388ea1c0c
CRs-Fixed: 2686309
Add support for processing the start scan response
WMI event. FW provides the necessary information to
segregate FFT bins to pri80, 5 MHz and sec80 in
160/165 MHz. Also, cfreq2 and the channel width is
provided to FW via WMI command.
CRs-Fixed: 2672081
Change-Id: I666b6c18a63d5d01117aa9cbd611691c6f8b2793
Add a dispatcher API ucfg_dfs_is_agile_rcac_enabled() to determine
if RCAC is supported for the given pdev.
Change the prototype of dfs_get_rcac_enable() to store rcac
config in a bool datatype.
Also, do a structure copy of ch_params of RCAC channel in
utils_dfs_get_rcac_channel().
CRs-Fixed: 2679975
Change-Id: I4b033463fc8111144bfffd3bb7e7d2bef6568c46
The range given/provided by the FW (low_5g, hi_5g), may contain both
5Ghz IEEE channels and 6Ghz IEEE channels.
Add an API wlan_reg_is_range_only6g to check if the input low and
high channel frequencies are only in the 6Ghz frequency range, and also,
place the API changes under a macro CONFIG_6G_FREQ_OVERLAP. First find
out if 5Ghz and/or 6Ghz range are available. Then, by applying the
method of exclusion find out if the range provided by the FW is only a
6G range.
Change-Id: I29675a6520a27257f3d1c7424b7f0c94797244cc
CRs-Fixed: 2676307
Trigger Rolling CAC SM events from
- NOL expiry (EV_RCAC_START) to trigger RCAC START with a
new channel if possible and not already running.
- Agile radar (EV_ADFS_RADAR_FOUND) to restart RCAC with a
new random channel.
- vdev restart (EV_RCAC_STOP) to stop the running RCAC when
the primary channel changes. Start will be based on the
availability of the new channel.
In case of the rolling CAC feature, a channel is programmed to
the agile detector on which CAC is running continuously.
Introduce an API that finds an RCAC completed channel and return
the channel params which will be used for the next channel
change.
Also add a boolean argument in dfs_set_current_channel api to
indicate if the dfs current channel is updated in the API
"dfs_set_current_channel".
CRs-Fixed: 2674621
Change-Id: Ica54a57f131cd54e47138f1cbeef2dd0023390ed
Some targets have a single synthesizer and it allows
a single Spectral detector to scan in 160 MHz /165 MHz.
Enable Agile Spectral scanning in 160 MHz / 165 MHz for
such targets. Agile creq2 will be populated in the WMI
command after WMI interface changes are merged.
CRs-Fixed: 2648480
Change-Id: I8522cbeeab29ac41479e3041eea376b081c0758a
As part of the Rolling CAC State Machine, introduce three state
enums (INIT, RUNNING and COMPLETE) and the corresponding state
events.
Introduce generic APIs such as dfs_rcac_sm_create,
dfs_rcac_sm_destroy and dfs_rcac_sm_deliver_evt for rolling
CAC State machine operations.
CRs-Fixed: 2659666
Change-Id: I528db71aa7d21dced7e47ff4f9cccfbfe94c8c21
Add an API wlan_reg_update_pdev_wireless_modes to update the wireless
modes in regulatory pdev_priv_obj with the wireless modes given as
input to it.
Change-Id: I2388b26da0d4c485b1b73b3ffb8f4b30767c31ee
CRs-Fixed: 2661579
Provide global function pointers for accessing DFS APIs that
1. Configures (enable/disable) rolling CAC feature.
2. Retrieves the current configuration of rolling CAC feature.
3. Programs a rolling CAC frequency.
4. Retrieves the current rolling CAC frequency.
CRs-Fixed: 2659495
Change-Id: I7fc63d150f4dc1cb5db4d671ff21c01caaf38aaf
This mode is supported through hw_mode_id 7. A special mode for
IPQ8074 platform alone to bring up single pdev alone on 2G mode.
FW would advertise the mode 7 support through the WMI service
ready message and this mode will be the default mode for AP-HK10 alone.
Added new APIs in tgt_reg to get pdev_id from phy_id and vice versa.
Fixed all places where pdev_id is used to acces psoc regulatory params
and converted them into use phy_id
Change-Id: I14920627f5e4ddafcc37440fa3281150b65ff04f
CRs-fixed: 2653042
Add RX Op function to update the FD template in case of
any updates to the FD frame parameters.
CRs-fixed: 2637082
Change-Id: I1d7b488d177a32ddc57129f227df26d5774aa9e1
In a future product, 160MHz mode of operation is acheived through
a single detector, unlike Hawkeye and its variants where 160MHz mode
is acheived using two 80MHz detectors.
Because of this change, the maximum segment ID is 0 in the new chipset,
whereas 1 in Hawkeye and its variants. Also the Agile detector ID
is 1 in the new chipset, 2 in Hawkeye and its variants.
In light of these changes, to identify the true 160MHz capability,
add a new API that checks the target type and returns true 160MHz
capability based on the target type. Also introduce a new dfs
variable that maintains the agile detector ID (based on the
true 160MHz capability).
In the future product, there is a support of restricted-80p80MHz
(a.k.a 165Mhz) where channels 132,136,140,144,149,153,157,161 are
available for operation as an 80p80Mhz channel.
Add a DFS API to check if this support is enabled.
CRs-Fixed: 2623964
Change-Id: If813e9d6fc649ce99c7780c04fbcb61acbd1af86
Current NOL conversion for dynamic mode switch is in such a way
that the NOL data is copied to the pdev ID entry for the targeted
mode. That is, the NOL data is split/merged before mode switch and
copied to a temporary structure before mode switch command is
sent to FW.
At this point, the target pdev's frequency range are still the old
values because of which, certain entries of the NOL data are missed.
Also in case of FW failures, the NOL entry cannot be added back
because they have been merged/split already.
To avoid the above, rearchitecture deinit and reinit NOL for
mode switch in such a way that the NOL data, as-it-is, is copied
before mode switch and is only split/merged after the frequency range
of the pdevs are properly mapped and the FW response is a success.
Change-Id: I4a073d1327ba182c40ced6089aa46d8f5f241d33
CRs-Fixed: 2632582
Supported dynamic HW mode switches:
DBS (full band 5G and 2G) <-> DBS_SBS (low band 5G, high band 5G and 2G)
Description of the changes:
1. NOL conversion:
a. Introduce a temporary NOL list copy structure in DFS psoc obj.
b. When mode switch is triggered:
i. Stop the NOL timers and clear the data, to avoid processing NOL
expiry during mode switch.
ii. Allocate the psoc NOL copy for the target num_radios.
iii. Store the NOL data of each radio to the target pdev ID
(pdev ID after mode switch) in the psoc NOL copy,
using a unified mux/demux API.
c. After mode switch is completed:
i. Resume NOL by re-initializing the list from the temporary psoc
copy.
ii. Free the psoc copy after mode switch is complete.
iii. Note: changes are made to support pause and resume of NOL,
increasing NOL timeout by a few milliseconds.
2. PreCAC list conversion:
a. When mode switch is triggered:
i. Stop the existing preCAC timer and send ADFS abort command to FW.
b. When mode switch is completed:
i. Unify/separate the preCAC list if the target mode is DBS/DBS_SBS
respectively, using a single API.
ii. Start ADFS again.
3. Radar detection lock:
a. While detecting radar, acquire a lock to avoid handling user triggered
mode_switch during this process. Release the lock once radar
processing is completed and CSA start is triggered.
4. Radar detection/CAC completion defer during mode switch:
a. While detecting radar or CAC completion, check if mode switch is
in progress. If yes, defer the processing and wait for mode switch to
complete before handling the events.
b. Note: Precedence is Radar over CAC, i.e., if CAC processing is waiting
and radar is received, CAC completion is no longer handled.
CRs-Fixed: 2580403
Change-Id: I506f3b569bad2e351c6f336e50f203cf5fa8b223
Add initial set of coex files, implement the basic functions.
Coex component is used to process coex related configurations.
CRs-Fixed: 2565088
Change-Id: I8b9600809691b808f97c621cb329a6ab9941814c
CFR config is passed on to FW through WMI
CFR feature code is moved into feature specific WMI file.
Change-Id: I00b57ea2ef4ec5520eb565910ac2c0a6478170e3
CRs-Fixed: 2582846
In regulatory non-offloads feature, send conformance_test_limit_2G,
conformance_test_limit_5G, reg_domain, reg_domain_2G and reg_domain_5G
information to firmware using WMI_PDEV_SET_REGDOMAIN_CMDID.
If all these attributes are not populated then CTL power limit is
not applied by the firmware.
Change-Id: I1523ab447aec64ec0af42da32318136f90fd17ca
CRs-Fixed: 2518246
Depending on the requirement, a bigger size or a smaller size for
the frequency variable can be chosen. The advantages of each size
are described below:
Advantage of a bigger size:
When two technologies (e.g. 802.11AX and 802.11AD) are controlled
by the same driver software, the frequency range may be very large
and a bigger size (e.g. 32bit integer) is more appropriate.
Advantage of a smaller size:
When the frequency range is not very large, a smaller size
(e.g. 16bit integer) can be used. It saves a large amount of space
especially when many large arrays containing elements of this type/size
are defined in the driver.
Also, change the size of the IEEE channel variables to unsigned
8-bit integer.
Change-Id: I6349c0665bf0a7329627427913f9eebba2821043
CRs-Fixed: 2586177
Add code to change the vdev_mlme timers to psoc_mlme timers
and also change code to send vdev_delete to FW while physical
destruction of vdev obj.
Change-Id: Ie041182155c75d0cc3825dc97b26abc6be38d76c
CRs-Fixed: 2563931
Wakelock is system level lock not required to be taken
for every vdev, Hence move the wakelock to the psoc
hierarchy.
Change-Id: I525baf5f4b5dcadb493d84900dbd0a2e7c6407f6
CRs-Fixed: 2563406
Move the vdev response timer from the vdev object manager structure
to the psoc mlme structure.
Change-Id: Ieb87ac6549aa23e0beb61441fea459d3db78c2f3
CRs-Fixed: 2563410
All gen III chipsets use Direct-DMA mechanism to copy Spectral reports to
the Host for further processing. This mechanism involves ring and buffer
management in the Host, FW, and uCode, where improper/incomplete DMA and
improper tail update issues are seen. DBR framework provides support to
debug such issues. Add Spectral control path support to facilitate the
configuration of these debug options.
CRs-Fixed: 2478596 2478595
Change-Id: I094616c4137145389b6984ccab933e5ebd0aa1ab
To enhance visibility of 6GHz AP, 6G only AP shall send
Fils Discovery frame periodically in one beacon interval.
Change-Id: I51487380fca10418d2260dc2612e2adcf6cbb93b
CRs-Fixed: 2562434
