Change the default connection dot11mode behavior of APs with
following security configuration which can support MLO:
1) WPA2 with PMF
2) WPA3-SAE with HnP (or H2E cap equals false)
Currently User has to force allow connection in MLO via INI or
else driver downgrades such candidates to 11ax.
Change-Id: I4ff232fc920e19e4f158eba3038abd57b045e705
CRs-Fixed: 3779433
Currently, firmware-reported unsafe channels are ignored
and userspace configured channels are honored when
coex_unsafe_chan_nb_user_prefer ini is set. This is supported for
SAP mode only.
But some platforms may want driver to ignore the firmware-
reported coex channels for P2P-GO also.
Enhance the ini to allow user to configure mode specific
bit as mentioned below,
BIT 0: Don't honor fw coex/unsafe channel info for SAP mode
BIT 1: Don't honor fw coex/unsafe channel info for P2P-GO mode
Change-Id: I91a2c6b2da9aba411d081f6ae3b23d374fe53159
CRs-Fixed: 3766393
User/wpa_supplicant disable roaming flag is only effective for current
connection, it will be cleared during new connection.
APP/wpa_supplicant can uses QCA_NL80211_VENDOR_SUBCMD_ROAMING to change
roaming behavior for current connection.
Change-Id: If9f439f51e25e3d67f5db5557c0d8f468b071596
CRs-Fixed: 3737996
Force single link on 2 GHz:
mlo_support_link_num=1, mlo_support_link_band=1
Force single link on 5 GHz:
mlo_support_link_num=1, mlo_support_link_band=2
Force single link on 6 GHz:
mlo_support_link_num=1, mlo_support_link_band=4
Force 2 links on 2+5 GHz, force assoc link 2 GHz:
mlo_support_link_num=2, mlo_support_link_band=0x13
Force 2 links on 2+5 GHz, force assoc link 5 GHz:
mlo_support_link_num=2, mlo_support_link_band=0x23
Force 2 links on 5+6 GHz, force assoc link 6 GHz:
mlo_support_link_num=2, mlo_support_link_band=0x46
Change-Id: Id6f56421528a42aa7059693845fe71a206bded93
CRs-Fixed: 3722009
Some solutions may not have HS-2.0 certification and there is
no need to forward the BTM frame to wpa_supplicant in such
solutions. Let firmware handle the frame in such cases by
enabling btm_offload so that it doesn't wakeup the host.
Firmware may roam to another AP upon BTM reception.
To enable/disable BTM offload add hs20_btm_offload_disable INI.
If this INI is enable BTM offload will be disable and if INI
is disable BTM offload will be enabled.
Change-Id: Id6e18404cc3a12a23b213c0f858c943715285932
CRs-Fixed: 3718776
Introduce INI to allow OEM vendor to configure driver
to connect to various EHT/MLO configuration APs which
are not allowed by default.
The vendor has to specify which APs to be allowed to
connect in EHT/MLO as a bitmap.
The list of configuration allowed are:
1) Connect to WPA2-PSK APs without PMF in EHT only
2) Connect to WPA2-PSK APs without PMF in MLO
3) Connect to WPA2-PSK APs with PMF in EHT only
4) Connect to WPA2-PSK APs with PMF in MLO
5) Connect to WPA2-SAE APs without H2E in EHT only
6) Connect to WPA2-SAE APs without H2E in MLO
Vendors may chose to connect in 802.11be without MLO
and to facilitate such configuration, the following
API is enhanced to take additional argument on whether
the given candidate can allow MLO or only EHT.
API: wlan_cm_is_eht_allowed_for_current_security()
Change-Id: I3ea1cc0b2c7ba96d1b25aba7bc851773edf27bd8
CRs-Fixed: 3693810
Suppose INI gDot11Mode is configured as 1 dot11mode_11a, but
the enum MLME_DOT11_MODE_ABG is defined at the last, which is
causing STA to connect in dot11mode_11ac.
So, lower dot11modes should be defined first. Change the order
of dot11mode_11abg to the initial enum value.
Change MLME dot11mode mapping to CSR dot11mode, passing to
csr_convert_mode_to_nw_type function.
Change-Id: I71972bed1b6ac25f809c980e9fff4829fae7e4ff
CRs-Fixed: 3686458
Add ini to disable mcs 12 13 for SAP operating in
2.4 GHz with 40 MHz bandwidth.
Change-Id: I78ed90bf6bab80a8f81f7a0640b9aca9d2736f4d
CRs-Fixed: 3672437
Add support for QCA_NL80211_VENDOR_SUBCMD_REGULATORY_TPC_INFO vendor
command to return the STA TPC information used within the BSS.
If STA is ML STA, multiple link TPC information will be returned to
userspace.
Change-Id: I6fd30893c057c876e9a01e112595e5cb0c906a70
CRs-Fixed: 3665538
As part of set feature set command, update STA_P2P,
STA_SAP, STA_NAN, STA_TDLS, STA_SAP_P2P, STA_SAP_NAN,
STA_P2P_NAN, STA_P2P_TDLS, STA_SAP_TDLS, STA_NAN_TDLS,
STA_SAP_P2P_TDLS, STA_SAP_NAN_TDLS, STA_P2P_P2P_TDLS,
STA_P2P_NAN_TDLS iface combinations to fw.
Also use WLAN_FEATURE_NO_P2P_CONCURRENCY sta dual p2p
support combination.
Change-Id: I315c219f79995dedb0c2856d326838351d8a3d5e
CRs-Fixed: 3674696
Driver cache all links channel bandwidth config from user space,
when link switch happened, and connect complete, send bandwidth
of the link id to fw.
CRs-Fixed: 3625801
Change-Id: I7d4a13075b62c9c8928d2c33bd309e9c5b085171
Currently, the expected range of sae_auth_failure_timeout
is 500-1000ms. DUT sta retries SAE authentication frame if it
hasn't received response within the configured time. But there
can be APs where there might be a timeout at AP and AP proceeds
with next frame(SAE confirm response) if the previous frame
is not acked by STA or SAE confirm request is not received
within this time.
Custom platforms may want to address this by retrying more
aggressively, e.g. retry within 100ms.
Add provision for the same by making min value as 100 ms.
Change-Id: I09fa57808edc6c00bda2dbe5d988558c7ef48e17
CRs-Fixed: 3662150
Add support for INI update_cw_allowed to enable or
disable update channel width via vendor command
QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH
Change-Id: I1f4ab2c7ca8dacb93442803336d59a4a5ffb1b47
CRs-Fixed: 3659655
Currently the ini "enable_responder_11az_support" is a boolean
value and applicable for enabling all the RSTA operations- 11az
TB and NTB ranging. Change the usage of existing ini
"enable_responder_11az_support" into a bitmap as below:
BIT 0 - 11az NTB
BIT 1 - 11az TB
Change-Id: I744e614eae4d89d9ff5d0e86398c0c94c8160d77
CRs-Fixed: 3651115
Add new dot11mode in MLME and update the utility functions to
derive the dot11mode based on the INI config and AP dot11 mode.
Change-Id: Ic53ab0cdd94dce75d6928270bc8bf4f8539ac96f
CRs-Fixed: 3653767
Use default link info is incorrect for mlo link.
Fetch link info by link id and update the bss rate flag.
Change-Id: I72a6747308b9873e18ea2bcb1b95cb915e668970
CRs-Fixed: 3643925
Add cfg to disable puncture in US LPI mode per FCC requirement,
set to false by default.
Change-Id: Id01f952b2a74ad64216a66d2d292166211440c4b
CRs-Fixed: 3649640
Disable puncture in US LPI mode per FCC request.
If bad FCC AP is detected, send WMI_VDEV_PARAM_CHWIDTH_WITH_NOTIFY with
reduced bw after setkey is done.
Also add the same bad FCC AP detection logic in HDD where bw increase req
from SS framework is handled.
When handle beacon update, also FCC AP detection logic to avoid wrong
channel switch.
If the AP removes or reduces puncturing pattern in new beacon, send
WMI_VDEV_PARAM_CHWIDTH_WITH_NOTIFY with increased bw.
For roaming case, after roaming, host will receive new beacon with new
bpcc, same as beacon update, use the same bad FCC AP detection logic and
send WMI_VDEV_PARAM_CHWIDTH_WITH_NOTIFY with updted bw right away or after
setkey is done (in case of hybrid roaming like OWE).
Change-Id: I6e85de879575d5c0a1960527f9018b4b33bf18d6
CRs-Fixed: 3631634
Currently the roam scan high RSSI delta is configured via INI.
Define an attribute to allow user configure high RSSI roam
trigger threshold. STA is expected to trigger roam if the current
connected AP's RSSI gets above this high RSSI threshold. STA's
roam attempt on high RSSI threshold aims to find candidates from
other better Wi-Fi bands.
This attribute value is given priority over the INI.
Use a new service bit WMI_SERVICE_5GHZ_HI_RSSI_ROAM_SUPPORT to
enable high RSSI roam trigger in 5 GHz as well.
Change-Id: Ide48ad2261b603de36bd1b31114b91c3a9d6606f
CRs-Fixed: 3586170
Userspace can dynamically modify association BW and as part of
disconnect need to reset the BW to original value, if not the
next connection will might happen with downgraded BW.
Currently the restore is happening on deflink VDEV instead of
actual disconnecting VDEV.
Fix this by changing function argument to accept link info
pointer in HDD adapter of that corresponding VDEV.
Additionally, the driver capability for 6 GHz-320 MHz is not
properly restored and further connections to 320 MHz are
happening on 160 MHz.
To fix the 160 MHz downgrade, use original EHT capabilities in
global MAC context instead of using modified EHT cap where
320 MHz support got reset on userspace dynamic BW update.
Change-Id: If2badb0a234f45d57dc186729bc529137d7a5131
CRs-Fixed: 3628940
Add ucfg wrapper API over the existing MLD ID get/set APIs
that will be invoked in HDD/OSIF.
Change-Id: I07d2e661c7e8129e54a0449f958749648c25e4ac
CRs-Fixed: 3621169
Add support for INI twt_disable_info to disable FW initiated
information frame for TWT
Change-Id: I06fe9be364d9def0ccfffc196ae31dcc2ab9a500
CRs-Fixed: 3621241
The host driver now sends a notification to the
firmware when a CSA (Channel Switch Announcement)
is rejected due to no change in channel, bandwidth,
or puncture.
Change-Id: I5d8a424459898d15a7931baf7ca4c3de8308c64e
CRs-Fixed: 3595843
The item "bss_max_idle_period" is not an ini item and we can only
use it's default value 0. It's not convenient to set it a value
that user required. So set it to an ini item.
Change-Id: Ie514992448cde192ffd6f1402a4477fabbbae741
CRs-Fixed: 3591728
Connecting event logs are to be sent after candidate
selection and not immediately after receiving
connect request.
Modify the connecting event logs to be sent after
sta info event logs.
Change-Id: I83b654ba0ef3458368ba7dd6353c5ab67077ec39
CRs-Fixed: 3599703
In the MLO-MBSSID test, STA can request information of
non-Tx BSS through Tx BSS by configuring non-Tx BSS MLD ID
within the ML probe request that is invoked as part of scan
request. Add support to configure MLD ID in scan start
params to FW.
Change-Id: Iec5a144e597a7f6b9b741f279e4424f975c5115c
CRs-Fixed: 3561040
During rrm_initialize () set RRM cap for Channel Load
and statistics to enable by default. Same rrm capabilities
driver sends to AP in association request during connection.
Change-Id: I3a9d87b8bd8b28b84ccc3578fff2ad1c7ebd8a6e
CRs-Fixed: 3609838
Active ini he_max_ampdu_len and change default value from 0 to 3.
Use min(ini, he_max_ampdu_len from F/W band/MAC cap) as final
he_config.
Mdm platform need set different value to pass throughput KPI.
Change-Id: Ib0580a0e68b72b6b7cd02d327ba643cfd1508080
CRs-Fixed: 3609154
For BTM certification cases, FW is unable to roam to
testbed AP BSS due to scoring logic. Reset the BTM
abridge flag that is used to enable FW to select
candidates based on score.
Change-Id: I29b6e1b5dea969263eb263103c6d2c10d5047f20
CRs-Fixed: 3591574
As per customer requirement, to enable or disable t2lm support
configure CFG_T2LM_NEGOTIATION_SUPPORT as INI.
Change-Id: I8eb4c78a04bbaa5ce0c155d04ddb793d31b092ee
CRs-Fixed: 3608649
For certain cert cases, roaming is disabled through
CAPI. Supplicant sends RSO disable to Host and the Host
disables BTM offload as well as part of roam disable.
But, for cases like load balancing, Firmware has the
logic to handle BTM requests with disassociation
imminent bit set to 1, by sending an event to Host to
trigger a T2LM request action frame rather than a BTM
response. Thus, set BTM offload bit even when roaming
is disabled to allow FW to handle BTM request frames
instead of supplicant.
Change-Id: Iaa0cbbce62dbb76518880ef2470d6d0819c501db
CRs-Fixed: 3590733
Firmware sends PEER_OPER_MODE_CHANGE event to host in SAP
mode when a connected client indicates upgrade/downgrade
of its bandwidth.
Host needs this data as any further SAP bandwidth
upgrade/downgrade should honor the indicated bandwidth for
that specific peer.
Change-Id: I50fecf670b47c56e3f33b8519fde1d5eaec7523f
CRs-Fixed: 3604716
Include BW_IND_ELEM IE in beacon and ECSA frames while advertising
CSA. This is needed when upgrading the bandwidth to 320 MHz.
Send the ECSA IE with switch count as 1. Use a timer to reset it
after sending the beacon out.
Change-Id: I6c38ef1ce4629b7a67bcbf803c7dbcced05ade33
CRs-Fixed: 3604422
SAP operating bandwidth may get updated due to concurrencies.
This might be temporary and SAP moves back to its original
bandwidth once concurrency is gone. So, add set and get APIs
to maintain the SAP current operating bandwidth.
These can be used during/after bandwidth update operations.
Change-Id: I386ad20bcbd0902672a890bde510ecc50e58512b
CRs-Fixed: 3600223
1. Upper layer sends QCA_WLAN_VENDOR_ATTR_LINK_STATE_CONTROL_MODE
vendor command to configure control mode in host/fw.
2. Host receives GET_ML_LINK_STATE driver command to return
control mode (configured at step 1) to upper layer.
Host should reply as a response of GET_ML_LINK_STATE with same
value of control mode configured at step 1 to upper layer.
Change-Id: I6ae82c2a1c0e4ff13cea678bf27916a3cda8ad81
CRs-Fixed: 3595730
Currently, if the AP advertises both Local and Regulatory
TPE IEs in the beacons, STA uses an INI to choose one over
the other. Vendor ask is to change this logic and allow STA
to use the minimum of the two TPE power limits. Also,
deprecate the INI that sets the preference between local
and regulatory TPE IEs.
CRs-Fixed: 3574510
Change-Id: Ibf19020d59621efa72cf290ef34c825fdb50e3e7
Move tSapChSelSpectInfo structure from sap component to mlme
component so that it can be use by LL_SAP as well
Change-Id: Ic3c2919054326aca3530071df27d425bb78a699a
CRs-Fixed: 3561182
