Enable direct buffer rx component in Kbuild since spectral scan gen3
based on this feature.
Change-Id: I8d44b35ca0d334917b3c052cc8ab4e47db34e4a1
CRs-Fixed: 2505676
Add support for WMI over QMI to reduce power consumption for
periodic stats report.
Change-Id: Iec725b357d9bcfa33029aedf7c568814499bc130
CRs-fixed: 2521826
Since CONFIG_ROME_IF is defined as "PCI" for lithium, PKTLOG_LEGACY is
getting enabled for lithium product as well. Disable PKTLOG_LEGACY for
lithium chipsets.
Change-Id: Ida237cd03e7006514120f9b2e37c7ad5c3897294
CRs-Fixed: 2532170
Enable configurable dfs_pri_multiplier. The ETSI typ2 type3 radar
detection ratio is lower than expected(>80%) while channel loading is
high(>30%). The host improvement for this are:
1. Add configurable dfs_pri_multiplier, controlled by
DFS_PRI_MULTIPLIER. Default value 2, min 1, max 10.
2. Lower adrastea ETSI type 2/3/4 radar filter rssi_threshold,
controlled by DFS_OVERRIDE_RF_THRESHOLD, dfs log shows that
QCS405 target report RSSI range [18, 45] while radar power
is 3 dbm. By using default rssi_threshold 24 will reject
many radar pulses, which leads to low detection ratio.
3. Calculate deltapri for each searchpri based on dfs_pri_multiplier
in dfs_count_the_other_delay_elements(), check deltapri
between [1, dfs_pri_multiplier] * refpri and searchpri, if
the primargin is desired, mark it as matched pulse.
4. Pick lowpri as refpri for the radar filter with
rf_ignore_pri_window equals to 0 while DFS_PRI_MULTIPLIER is
enabled. Observed original findref logic has some problems
which selects refpri is bigger than lowpri, which leads to
the lowpri pulses pri_match are set to 0, and in this case,
radar was not detected. Example for the issue, assume
rf->rf_pulseid 34 (ETSI type 2) has 7 pulses with pri:
1489, 2978, 2978, 2978, 1489, 2978, 1489 us in this case,
highscore is 4 (2978), scoreindex is 5, refpri is 2978, which
leads to: index 0, 4, 6 pulses with pri_match 0 in
dfs_count_the_other_delay_elements(). The fix is to select
lowpri as refpri(1489 in this case).
Change-Id: I1f3ca3298c9ab1f1e2651ad6b4a0a4810f83f8a1
CRs-Fixed: 2522506
This is a propagation of qcacld-2.0 commit 98821c7dcf49d ("qcacld-2.0:
Add CONFIG_MULTI_IF_LOG to support multi if log"). Add CONFIG_MULTI_IF_LOG
to support multi if log by assigning the specific netlink protocol
when dual wlan cards are loaded.
Change-Id: I3ea9574899c23a8d2ebbdea5b958cc3ad7947fe5
CRs-Fixed: 2525483
Some target chipset support fw stats version 2, but we didn't enable
it in some configure file. Enable it in these configure files which
depend on chipset.
Change-Id: Ief8b87bdb466a1838e6a61928f0154868f0ff220
CRs-Fixed: 2524266
6 GHZ has introduced new set of frequency based APIs. Also there is
conditional usage of 6 GHZ band. Add configuration items for these.
Change-Id: I22703989ec7e6711af640f1f9d0afded46026b8a
CRs-Fixed: 2513098
The pktlog will fail with ROME module due to the change IDs:
I24776caa3b78ec38d94421f243ec72d81ee3102d
Ifb70ac0993f2402201f88758845f730cf677b1a0
Define new macro PKTLOG_LEGACY for HELIUM/ROME to avoid the ROME PKTLOG
failure.
Change-Id: Ibaa20b7af208a261e0fd8682de45ad8eb4a69212
CRs-Fixed: 2520696
The member of type_specific_data is not valid for ROME module. Add macro
protection for type_specific_data in the ath_pktlog_hdr to avoid offset
error when getting the msdu id info during processing pktlog TX info.
Change-Id: Icb8b95cef9a32732116522e4fc3b39067ff36037
CRs-Fixed: 2522277
Use QCS40X instead of QCS405 in config files. Kernel defconfig files for
QCS405 and QCS403 has been separated recently, and the arch has been
changed between these two chips. But all QCS related features and changes
in cld should all be included, so use CONFIG_ARCH_QCS40X to replace
CONFIG_ARCH_QCS405.
Change-Id: I6f0837bb3d3f1530aea5b2d4912741beb8c313bd
CRs-Fixed: 2519267
Disable fw log parsing feature config flag for Lithium
targets as firmware will no longer use WMI events for
sending logs.
With Lithium config flag disabled:
text data bss dec hex wlan.ko size
6767311 251817 2424616 9443744 9019a0 17096KB
With Lithium config flag enabled:
text data bss dec hex wlan.ko size
6699206 81613 2423872 9204691 8c73d3 16768KB
Change-Id: I536a20a0c0d7c4abcee775e3007d1749a21b648b
CRs-Fixed: 2504803
Featurize DHCP indication for SAP and disable it
for QCN7605 as this feature is broken for HL
Data Path.
Change-Id: If1db649131d887a2aab18461187403b4b9a2c5b4
CRs-Fixed: 2496032
Do not enable unit-test framework by default for all Lithium
targets. Unit-test framework should only be enabled in debug builds.
Change-Id: I709d13ebb35302787377c8f36a8db0f04c2e794e
CRs-Fixed: 2498069
Currently ext scan is enabled by default in driver which
is increasing driver size significantly and ext scan
is not getting used anymore.
Disable ext scan with feature flag CONFIG_FEATURE_WLAN_EXTSCAN
to reduce driver size.
Change-Id: Id0fdeae6e6b71f53d3b73322aca659254d52cec8
CRs-Fixed: 2491452
Check if host is reaping a descriptor which is already
reaped then drop RX desc processing instead of asserting.
Macro DUP_RX_DESC_WAR added before dp_rx_dump_info_and_assert function
which does not assert for the case WAR is enabled.
Change-Id: I8a095d33e4f7e868340d9a76618c064af764386d
CRs-Fixed: 2487793
This command is used to send OEM data binary blobs
from application/service to firmware.
Change-Id: I0b5d7dd5a030b70e59c8581fb51d99079b38385f
CRs-Fixed: 2477332
Currently there is no ini support to configure frequencies
which needs to be avoided for the acs channel list which
may allow SAP to come up on a channel which is not preferred.
For Example there are many legacy clients which supports
2.4GHz but don't support channel 12 and 13 (or does not have
the capability to detect country change where channel 12 and
13 is valid).
In that case, if SAP comes up on channel 12/13, those legacy
clients won't be able to connect to AP.
Hence, Add a feature flag and ini to configure the frequency
list which can be avoided during acs.
Change-Id: Id106b38228f837ba056eb916004dc012e919ddd2
CRs-Fixed: 2472004
CONFIG_CHNL_MATRIX_RESTRICTION should not be defined by default.
CONFIG_CHNL_MATRIX_RESTRICTION should not be defined by HST.
Change-Id: I36154976c4e106d9910977b5990f796b889eaf82
CRs-Fixed: 2476488
Disable LFR2 in cld-3.2 mainline as roaming is offloaded
to firmware in LFR3. Also fix linker issues with lfr2 disabled.
Featurize LFR2 properly with adding correct header files
and bringing LFR2 only functions under WLAN_FEATURE_HOST_ROAM
compile time flag.
Change-Id: Iac81b693feaab503d371753a4d16cc3e70df2a87
CRs-Fixed: 2459786
Add feature flags DP_FLOW_CTL to featurize DP flowctl ops,
DP_PEER_MGMT to featurize peer handling in DP,
DP_POWER_SAVE to featurize power saving ops in DP.
Change-Id: I02f487fec846e9dd9ffcaf53a10e49e7a3365fff
Add a feature flag enabling support in defconfig
for the datapath event history logging feature.
CRs-Fixed: 2466616
Change-Id: I8fc2c76a927aea3e2e723cde87c69e59e03a9848
Propagation from qcacld2.0 to qcacld3.0.
The WMI CMD and EVENT of "get antenna isolation" are already defined,
but not used before in qcacld3.0.
Now, The host driver uses vendor command to get this information
instead of iwpriv command in qcacld-2.0.
The attribution of this feature is already defined in file
"qca_vendor.h". The name is "QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION".
So host driver will use vendor command
"QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY" to get the information
from lower layer.
Change-Id: I915768f622ddc9a70a95ce4fe952f19917a8f901
CRs-Fixed: 2447360
Add QCA_LL_PDEV_TX_FLOW_CONTROL for both
QCA_LL_LEGACY_TX_FLOW_CONTROL and QCA_LL_TX_FLOW_CONTROL_V2
disabled platform, avoid frame drop in driver which leads to bad TCP
TX throughput. Change NUM_TX_QUEUES to 5 for this case to avoid invalid
memory access in wlan_hdd_netif_queue_control().
Change-Id: Ifa649e31a41d1bf89eadc8cc7e9520f0e27b9fe4
CRs-Fixed: 2466996
Currently the export symbols are enabled in the driver
which is increasing the text section of driver.
Since driver does not need export symbols, disable it.
Change-Id: I463835107fc2a86ee6b4ab36edc75571f644499f
CRs-Fixed: 2462388
Link BLM exposed APIs to the following:-
1. csr_get_scan_result:- Link this API with filter bssids in
the reject ap list maintained by the blacklist mgr.
2. lim_assoc_rej_add_to_rssi_based_reject_list:- Link this API
with the the blacklist mgr add bssid to reject list to add the
OCE and BTM related assoc rejects.
3. Userspace avoid list parsing logic for the userspace to set
the BSSID as avoided.
Change-Id: Id51ffb80cea3f845fefe14db25d0f7acda6ea0f3
CRs-Fixed: 2461281
WiFi chip in SDXPRAIRIE supports DBS, and it is OK to start AP+AP in
DFS channel in DBS mode.
If CONFIG_FEATURE_WLAN_STA_AP_MODE_DFS_DISABLE is defined, AP+AP in
DFS channel in DBS mode fails to start.
Remove CONFIG_FEATURE_WLAN_STA_AP_MODE_DFS_DISABLE definition to make
AP+AP in DFS channel in DBS mode work for SDXPRAIRIE.
Change-Id: I1947b480aca2acb3245350c73935f6a4f9af964f
CRs-Fixed: 2459215
Implement the interface to transfer the info between
host driver and firmware about the ap which has interop
issues with the DUT. It is detected by firmware and
forwarded to user sapce for persistent storage. And
user space configs these APs to firmware when the DUT
starts up next time.
CRs-Fixed: 2425202
Change-Id: I2e828d521f0e04862a01fa1c90626f51b7f65796
Add a compile time feature flag by name RX_DESC_MULTI_PAGE_ALLOC
which will enable the memory allocation of RX descriptors using
multiple pages instead of large contiguous memory.
Change-Id: Ia3803a3685c605c79a34a0c2c000d7ed4adb7d97
CRs-Fixed: 2456267
Add new vendor cmd : QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING.
This subcommand is used to implement asynchronous beacon
reporting feature. Userspace can request driver/firmware to
report details of each beacon received whose bssid is same as
currently connected BSS's mac address. The driver will encapsulate
the details of these beacons as an asynchronous event within this
command id until userspace requests to stop sending beacons.
Change-Id: I9a32fe5431767b077983c7db90a2f825709f368c
CRs-Fixed: 2431351
Adaptive 11r feature that enables the AP to support FT-AKM
without configuring the FT-AKM in the network. The AP will
advertise non-FT akm with a vendor specific IE having Adaptive
11r bit set to 1 in the IE data. The AP also advertises the
MDE in beacon/probe response.
The STA should check the adaptive 11r capability if the AP
advertises MDE in beacon/probe and adaptive 11r capability in
vendor specific IE. If adaptive 11r capability is found,
STA should advertise the FT equivalent of the non-FT AKM.
Introdue a compile time flag WLAN_ADAPTIVE_11R_ENABLED to
enable/disable adaptive 11r support.
If the AP is adaptive 11r capable, set the is_adaptive_11r_ap
flag in bss descrtiptor. This flag will be sent in join request
and populated to pe_session. Also mark the CSR session as
adaptive 11r session based on this flag.
Add changes to check for the adaptive 11r service capability
advertised by firmware. If the host driver connects to adaptive
11r AP, enable RSO only if the firmware advertises adaptive
11r capability, else RSO should be disabled.
If the connection is adaptive 11r connection and if the adaptive
11r ini is enabled, set the adaptive_11r flag in
wmi_roam_11r_offload_tlv_param sent over the wmi command
WMI_ROAM_SCAN_MODE to the firmware. This will enable firmware to
filter the adaptive 11r AP from roam scan results.
Change-Id: If27a2393e3f4bb68942f5ebcec0135f57627f16b
CRs-Fixed: 2437988
Use WLAN_FEATURE_DP_BUS_BANDWIDTH to instead of MSM_PLATFORM for better
reading.
Change-Id: Iaed4f77b09b80ca8872a69c832491598db021232
CRs-Fixed: 2423299
