This mode is supported through hw_mode_id 7. A special mode for
IPQ8074 platform alone to bring up single pdev alone on 2G mode.
FW would advertise the mode 7 support through the WMI service
ready message and this mode will be the default mode for AP-HK10 alone.
Added preferred_hw_mode and target_pdev_id into dp structures so that
they can be used to configure the dp rings for this particular mode.
Also changed the lmac_id to target_pdev_id mapping for mode 7.
Change-Id: I3aae46fea13132eebaf7d37cff68ef517253d229
In case the bus is in low power mode, the register writes (followed by a
memory barrier) may take a long time (~4ms). This can cause the caller
to block till the PCIe write is completed. Thus, even though PCI
writes are posted, it can still block the caller.
Hence, in case the bus is in low power mode (not in M0), or not in high
throughput scenarios, queue the register write in a workqueue. The
register write will happen in the delayed work context. In other cases,
i.e ,when the bus is not in low power mode or in high thoughput
scenarios, do the register writes in caller context.
Change-Id: Idf218e4581545bc6ac67b91d0f70d495387ca90e
CRs-Fixed: 2602029
Add doppler and spatial reuse in ppdu descriptor to be able to use it on
HE information for tx capture
Change-Id: Id87a692a89d00c64929624c22c2efc27bc873e43
Change set 2 of ctrl_ops APIs to replace pdev, vdev and peer
dp handles with pdev_id, vdev_id and peer mac address
along with dp soc handle
Change-Id: I3f180c9c360d564f0b229b447074ad23b7c0a737
Add new parameters for converging multiple set/get
APIs into common psoc/pdev/vdev/peer set/get APIs.
Change-Id: I0802dea028c9e935ef899169cf7d86f2dc7632bc
Change set 1 of the ctrl_ops APIs to replace pdev, vdev and peer
dp handles with pdev_id, vdev_id and peer mac address
along with dp soc handle
Change-Id: Iedf6dea2215d3d04b2212c71c8ec8c7328c559e8
CFR information extracted from PPDU status TLVs is already stored in
HAL ppdu structure. Extract the same and copy it to CDP ppdu structure.
This is delivered to subscribers through a WDI event, similar to PPDU
stats.
Change-Id: I4315626c7f79f85b75b8d1b9e1e5caf8d65abed9
CRs-Fixed: 2593416
Change cmn_ops APIs to replace pdev, vdev and peer
dp handles with pdev_id, vdev_id and peer mac address
along with dp soc handle
Change-Id: I5716a87cad56b1dfe8dd56f193bbb6ff923a6af1
as we are overriding bar ppdu information, we need bar start/end
timestamp and duration.
added resp_type, mprot_type, rts_success and rts_failure in
cdp completion user.
Change-Id: I53c215e948fad8d079e1d4c40ec07d34aff1fefe
Remove pdev and vdev control path handles from data path.
Instead send pdev_id and vdev_id along with opaque soc
handle in ol_if_ops.
Change-Id: I6ee083f07e464f283da0d70ada70a4e10e18e1b2
Currently the cdp apis are given pdev/vdev/peer
handle as its arguments, which is directly
accessed in those APIs. This can cause a
race-condition in access of the respective
handles, if it has been deleted in parallel.
Hence as a part of cdp convergence, pass only
the pdev/vdev id or peer mac address, which will be
used to get the respective handles, and hence
avoiding the unwanted access of the handles, if
it has been deleted.
Converged misc_ops
- tx_non_std
- get_opmode
- get_tx_ack_stats
- set_ibss_vdev_heart_beat_timer
- hl_tdls_flag_reset
- set_wisa_mode
- txrx_post_data_stall_event
- update_mac_id
- pkt_log_init
- pkt_log_con_service
- get_num_rx_contexts
- set_wmm_param
- flush_rx_frames
- bad_peer_txctl_set_setting
- bad_peer_txctl_update_threshold
- txrx_data_stall_cb_register
- txrx_data_stall_cb_deregister
- vdev_set_driver_del_ack_enable
- get_intra_bss_fwd_pkts_count
- mark_first_wakeup_packet
- register_pktdump_cb
- unregister_pktdump_cb
- pdev_reset_driver_del_ack
- runtime_suspend
- runtime_resume
CRs-Fixed: 2539811
Change-Id: I3080df033d6411d7078a322224b914bda2fddc0e
When a particular vdev is deleted, the corresponding rx
packets which have been queued to the rx thread are not
flushed. Hence when such packets are submitted to the
network stack, the dev for this skb will be invalid,
since we have already freed the adapter.
Flush out the packets in the rx thread queues, before
deleting the vdev.
CRs-Fixed: 2543392
Change-Id: I2490d0f5ce965f62152613a17a59232521ca058f
Add the soc context for ol_txrx,
The soc layer is used to hold the ol_pdev context.
CRs-Fixed: 2539807
Change-Id: I751ad61de55db9d86624b8b5e18b0981ffb0338d
In cases where one of the interfaces is a P2P-GO and
IPA has been enabled, the P2P connection establishment
fails.
When IPA is enabled, the REO destination is changed to REO4
which can be reaped only by IPA module. But in case of P2P-GO
interface in operation, this change in configuration causes
all the RX packets to be stalled due to incorrect REO configuration.
Hence, to avoid this case, do not change the REO dest config
when the interface subtype is P2P.
CRs-Fixed: 2498315
Change-Id: Ie9f01c3b353c7c0503e1541d6c79c2f47c9782f3
Process smart antenna fields from tlv
HTT_PPDU_STATS_USR_COMPLTN_COMMON_TLV in tx
completion path and export it to tx_completion.
Change-Id: If14e711b0aee8e583fd329f3c3915904649ffe47
CRs-Fixed: 2491429
Since tx_monitor mode and rx_monitor mode consume signficant MIPS
when enabled on a per-peer basis, new requirement is to enable such
functionality on a per-peer basis. New CDP APIs are added to set these
per-peer parameters.
CRs-Fixed: 2494471
Change-Id: Ib44845ec98481cc4df36c30f47335522e5274568
In case of TCP packets being processed by dp_rx_process, send out GRO
flush indication to the thread.
CRs-Fixed: 2500152
Change-Id: I4f464456d423e4680955992c0acf0ed5f4e618b8
Read extra bits of fcs okay bit map from
RX_PPDU_END_USER_STATS_EXT TLV and use the same
to send first fcs okay packet in case of M COPY
CRs-Fixed: 2499150
Change-Id: I1a25971ea789dd7fddddb312af8a18a4cccdc178
Tags are programmed using wlanconfig commands. Rx IPv4/v6
TCP/UDP packets matching a 5-tuple are tagged using HawkeyeV2 hardware.
Tags are populated in the skb->cb in the REO/exception/monitor data
path and sent to upper stack
CRs-Fixed: 2502311
Change-Id: I7c999e75fab43b6ecb6f9d9fd4b0351f0b9cfda8
1. Remove vlan tag in tx and enqueue to hardware.
2. Add vlan tag in rx after peer-vlan_id lookup.
Change-Id: I932202540ac03cabdd20ffd4849fe759ea8a7abb
Update rx error stats. It is a summation of below failures:
- desc_alloc_failure [No free desc available]
- csum error [IP/TCP_UDP]
These failure stats are updated at pdev level and no need
to aggregate this.Directly add at pdev level and export.
Change-Id: I0a5fa8f972babf092163f3cb2d0093547ded4877
CRs-Fixed: 2496037
Add code to remove void pointer usage for hif_handle
and use opaque pointer hif_opaque_softc and also use
cdp_soc for opaque DP soc handle
Change-Id: I2896f7704ffb809214c5b08756c4b8673307fd9e
CRs-Fixed: 2487247
Make change to remove usage of void pointers for
ctrl psoc in DP and instead use a opaque pointer
struct cdp_ctrl_objmgr_psoc.
Change-Id: I9fac21db1156378fc10b95cf10517afa4364da00
CRs-Fixed: 2484411
Add code to use cdp_vdev instead of void pointer for
API dp_tx_send_exception and dp_tx_send_mesh
Change-Id: I63ca5a62c2a8cd6feb906181702888814650dfce
CRs-Fixed: 2480836
Add new CDP API cdp_register_rx_mic_error_ind_handler to
register rx mic error callback. Also, define new structure
cdp_rx_mic_err_info for holding MIC error information.
Change-Id: I4d5d6426b1d5f04848afd48f6dbf51edba291a20
CRs-Fixed: 2488424
fix memory leak issue in tx mgmt ctrl payload tlv.
if any of the mgmt or pkt capture feature is turned on.
htt_t2h_msg is hold in mgmt_buf and not set to NULL on free.
which cause leaking next target to host nbuf.
Change-Id: I0d9e0194e51a21b348aadf747b8c9def5c245eda
Add feature flags DP_FLOW_CTL for DP flowctl ops,
DP_PEER_SUPPORT_OPS to support peer handling in DP,
DP_POWER_SAVE for power saving ops in DP, DP_CON_MON DP_MOB_DEFS
DP_INVALID_PEER_ASSERT DP_PRINT_NO_CONSOLE and DP_INTR_POLL_BOTH.
Change-Id: I01dafadf6578c0b5f36ab3ef56624912fb66b100
CRs-Fixed: 2467170
Read rssi_chain per nss per bw and from rx status TLVs
and update to host data structures.
CRs-Fixed: 2445933
Change-Id: I275e9e502a0a724410fc189ac293cadc8f2981e0
Identify the WIN/MCC specific features. Move the features under feature
specific flags. Get rid of WIN/MCC specific code.
Change-Id: Iaf4e5befd7d574a20bea5c078201adbeac3b762c
The following changes are made
-Yield dp_rx_process if poll time exceeds
-Yield dp_tx_comp_handler if poll time exceeds
-Interrupt statistics to track various interrupt contexts and
corresponding interrupt masks
-Add poll times histogram buckets to NAPI stats
Change-Id: I8c7a6bbbb97c7b3dd1dde6ac3a97113c433086a2
CRs-Fixed: 2423879
Currently there is no support to update tx stats for
non-qos frame. Update tx stats for non-qos data frames
Change-Id: Ib61dd6e3b0c676b5af806c4b1e5cca22ea6ffaa5
CRs-Fixed: 2421925
