Currently, for Dual DSI Broadcast command, Overflow error
is masked only for master controller. This changes add
support to mask overflow error for slave controller as well.
Change-Id: Ida73c4166e996fcf2c8c936d0c76d0a89a220d89
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
The change adds register mapping of MDP_INTF_[1/2]_TEAR_INT_COUNT_VAL
register to DSI controller. This allows for the controller to read the
line count and frame count of the read pointer during trigger and
successful transfer of DMA command.
To enable the debug feature:
echo 1 > /d/<panel_name>/dsi-ctrl-0/enable_cmd_dma_stats.
To disable the debug feature
echo 0 > /d/<panel_name>/dsi-ctrl-0/enable_cmd_dma_stats.
To read line count value:
cat /d/<panel_name>/dsi-ctrl-0/cmd_dma_stats.
Change-Id: I5cdeb54ca941af05b226a9d7ab332b899ecc5797
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add support to read register ranges and IRQ lines that needs
isolation during VM switch in dsi ctrl and dsi phy.
Register for VM resource collection event providing the
callback function.
Change-Id: I5eae4699b0a97ffed438627ccea855c401b3fbeb
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Display in trusted VM works in a handover mode i.e, all
display components need to be initialized by the primary VM
before switching to trusted VM on the usecase boundary.
That makes it a hard requirement for the trusted VM not to
re-program any of the display configuration registers before
it could hand the HW back to the primary VM.
Also, most of the linux framework drivers including pintrl, clocks
are not enabled in the trusted VM.
In order to address the above two limitations and to control the
probe/commit sequences, this change adapts the same path as that
of continuous splash to bypass some of the critical functions
which are identified to be HW intrusive. Based on the DT property
read from SDE handle, dsi drivers will choose to bypass
enable/disable HW state updates when executing in the vm environment.
Change-Id: Ica71c924d189ab65fe3be5b0ac870633e3b749e1
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change fixes the usecase where dsi msg flags validated only
during command transfer. This fix maintains the flags between
transfer and trigger calls. It also adds a new async override
flag to be used to bypass validate function.
Change-Id: Ie12acd3d7b01099bba65ca37cec61091408b81c5
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
If DPU hardware supports demura feature, install the connector
properties related to demura feature.
Change-Id: Ieaddfc695e9f57e3c45e2bc0bd2c2e103f895ba8
Signed-off-by: Gopikrishnaiah Anandan <agopik@codeaurora.org>
DSI driver did not use msm bus scaling setting,
remove the code.
Change-Id: I71675c8f4e3e97f1ded72ecac3fa87bdc7fb3774
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
The current solution triggers the DMA command and waits till
the command dma done and ISR signals completion. This change
introduces asynchronous wait after a DCS command has been
triggered. Enable this mode only during pre kickoff, so as to not
block commit thread.
Change-Id: Iead7b6328883e844147d47ff68dc878943879553
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change is a snapshot of dsi files taken of 4.14
as of commit 764f7c2 (Merge remote-tracking branch
'quic/dev/msm-4.14-display' into msm-4.14)
Change-Id: I8361a844c35a4450f7800964a8da2741676fd6c7
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Change updates frame transfer time calculations. Frame threshold
is provided as input to decide on the final transfer time.
Panel dsi clock node followed by mdp transfer time node
will take priority in selecting final transfer time than frame
threshold time.
Change-Id: I40c3abfc635cd9b338b705535612ac32e047ce6e
Signed-off-by: Vara Reddy <varar@codeaurora.org>
This change adds support for dynamic switching of dsi clocks
to avoid RF interference issues. Also with dynamic dsi clock
switch feature coming into picture, now populate the supported
refresh rate as list instead of providing a range. Modify the
logic to enumerate all the modes in dsi driver, taking dynamic
bit clocks, resolutions and refresh rates into account.
Change-Id: I5b6e62bc935cf2234bdd96fcb3c7537b4e735fff
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Yujun Zhang <yujunzhang@codeaurora.org>
Change updates dsi clock calculations for command mode
as per recommendation. Now dsi clocks are tied to
frame transer time. Propagate correct frame transfer
time to hal to update mdp clocks and bandwidth needed
accordingly.
Change-Id: I46f9038622ddd47cc53c5f3d54229f69a7008c8a
Signed-off-by: Vara Reddy <varar@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
