Before sending vdev delete command to target_if layer, attach vdev
delete params to wma_txrx_node's del_staself_req member in wma layer.
This helps while responding to vdev delete command in case wmi service
"wmi_service_sync_delete_cmds" is disabled.
VDEV delete command response is sent to upper layer even vdev_mlme
object is not found.
Change-Id: Idfd8b036ff1ea676dd3ad8be703512ff84f299b7
CRs-Fixed: 2510460
Configuration for Issue:-
DUT configuration:-
1. Configure DUT's country as US where channel 165 does
not support channel bandwidth of 40 mhz.
AP Configuration:-
1 Configure the AP in a country where channel 165
supports channel bandwidth 40MHZ.
Scenario of the issue:-
1.Connect to a diff AP on some channel x with same SSID,
and then roam to this AP.
Observation:-
The DUT would connect in 40 mhz to this AP instead of 20Mhz,
which violates the DUT's country reg rules.
Expectation:-
The DUT should re-connect only in 20Mhz on channel 165, or
only in max BW supported by reg in that country.
Issue:-
The DUT does not consider the max bandwidth allowed for the channel
in the country configured, and allow the re-association only
in the respective bandwidth.
Fix:-
Send the max BW supported by the channels in the current
reg domain to the FW so that it considers the max BW of the
channel and AP capability and then roam in the respective BW
only.
Change-Id: I1730d6c65d3dd305dcf2ebe340c3d5ad950761d7
CRs-Fixed: 2504900
Reduce the log level from err or info to debug so that logs
are not printed on console.
Change-Id: I0d33c2a8f5b4bb4974656ac0d1eb6713a74cb5f4
CRs-Fixed: 2516281
As part of RSO update config, roam scan mode is set to 4 before
the WMI_ROAM_SCAN_RSSI_THRESHOLD command is sent to the firmware.
And after WMI_ROAM_SCAN_RSSI_THRESHOLD is sent, the roam scan
mode value is again set back to 7(value 7 enables RSSI scan and
periodic scan). There is a very small window between these two
commands where BMISS event is received and firmware forwards it
to the host which causes a disconnection.
Fix is to disable sending roam scan mode to 4 before sending the
WMI_ROAM_SCAN_RSSI_THRESHOLD command.
Change-Id: I2c22308d711e71e67d132a0bd121aed66497998b
CRs-Fixed: 2508762
Currently Host issue a disconnect and cleanup for current AP,
even if the offloaded roaming feature has started, but has not
completed for some reason. This results in connection loss with
the current AP.
Fix is to call abort event SIR_ROAMING_ABORT in case of roaming
offload timeout in order to maintain the connection with the
current AP.
Change-Id: I4168f8aeb7a759896a5d93e1918ce6542e61b37e
CRs-Fixed: 2508449
WMA interface PMF capability is vdev configuration hence do not
update the capability in WMA interface based on peer capability.
Change-Id: I08b39b9bc631321aa77aa1ab3bcbf1841bb3dda1
CRs-Fixed: 2504060
As part of vdev target if convergence the new vdev command
resp time are defined in target if layer.
So use the vdev timer values from target if.
Change-Id: Ib74f91331e4cb470233e678ded9159e17045467e
CRs-fixed: 2513794
Topic: 6ghz_chan_to_freq
Convert channel to freq in tpAddBssParams and wma_vdev_start_req
structure to avoid duplicate channel numbers in 6ghz, and 2.4ghz
operation.
Change-Id: I8f657a566d1555efa07bf9155b84c37431c57f86
Crs-Fixed: 2511312
Userspace can configure different roam triggers as defined
in qca_vendor_roam_triggers through the roam subcmd
QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET and the
attribute QCA_ATTR_ROAM_CONTROL_TRIGGERS. Send the roam trigger
bitmap to firmware
Change-Id: I692110a2ae1ee5a35bb248b9138080a7dfb02cf6
CRs-Fixed: 2508776
Userspace can update the full scan period through the roam subcmd
QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET and the attribute
QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD. Send the same to firmware
as part of roam scan offload command
Change-Id: I7c1046763d693faa3340b655848d3306ef92e06c
CRs-Fixed: 2508775
Force set peer's phymode to the phymode of current interface if first
one big then second one, then TDLS link can't select more better
phymode when DUT support VHT mode and connect to 11A mode AP.
Change-Id: Idc72e04dcdf7ead3b52effc2c06862bc9dddd732
CRs-Fixed: 2512622
Set hidden_ssid when restart sap on another channel, currently tested 2
methods to restart sap on another channel: 1, force-scc switch to station
channel; 2, iwpriv wlan1 setChanChange x. Both of them run into error
state: with hidden_ssid set in hostapd.conf: ignore_broadcast_ssid=1,
after channel switch, APUT reply broadcast probe request with it's SSID.
Copy pe session parameter: ssidHidden which stored user setting to next
channel vdev start.
Change-Id: I56580529e2b0db673c6b28c75094a7fd225cba77
CRs-Fixed: 2506214
Unused members of delete bss params structure are removed
and structure is re-framed.
Change-Id: Ib2e7c72e0636765341792a79aa12968a84ed4879
CRs-Fixed: 2512877
Legacy code releases vdev start wakelock after vdev down
command sent to firmware to overcome race condition. Target_if
common code takes care for wakelocks.
Hence, do not release start wakelock in legacy code.
Change-Id: I550ffb17e2e29f3b0bad618dc9ef9463a94800aa
CRs-Fixed: 2512151
Refactor vdev stop and down code to target_if common code.
Remove legacy code for vdev stop and down.
Change-Id: I4ab0743d39a3b37816ab9f18e8850cadf1335c15
CRs-Fixed: 2506649
In "Change-Id: I2896f7704ffb809214c5b08756c4b8673307fd9e", parameter
type of hif_get_hal_handle changed from void to hif_opaque_softc,
which cause compilation failure in wma_init_dbr_params.
Change-Id: Idbb591bb1ea1507661882fe48b18eaaffcac164d
CRs-Fixed: 2504894
There is only vdev start, stop, and set-key wakelocks for system suspend
as of now. Add vdev start, stop, and set-key wakelocks for runtime PM
also.
Change-Id: Ic071bcfb112ae8861a446298677d190484f0c01b
CRs-Fixed: 2507852
Convert channel to freq in vdev start structure to
avoid duplicate channel numbers in 6ghz, and 2.4ghz
operation.
Change-Id: Ie78d93a34d1d558b9c94fc8a54aa95ee07bda55e
CRs-Fixed: 2508040
Currently the host driver blocks roam scan offload command to
the target if the connected akm is OWE or SAE.
Add changes to read the WMI_SERVICE_WPA3_SAE_ROAM_SUPPORT and
WMI_SERVICE_WPA3_OWE_ROAM_SUPPORT service capability advertised
by the target and set it to the mlme fw_akm_bitmap. Read this
bitmap in csr_roam_offload_scan() to allow RSO command.
Also the connected akm is sent to the target via the
WMI_AP_PROFILE command. Translate the CSR akm type for OWE and
SAE akm also.
Change-Id: I68527722ab099e0c8e1681ed64ea416b9a6e9936
CRs-Fixed: 2491021
For WPA3 SAE LFR-3.0 roaming, authentication is offloaded to the
wpa_supplicant via the host driver due to the target crypto
inavailability limitations. The target does candidate selection
and sends the WMI_ROAM_PREAUTH_START_CMDID to the driver.
Once the SAE authentication is done, the supplicant sends the
external auth NL command with the authentication status, PMKID
derived. On receiving this event, send the PMKID, bssid, auth
status to the target over WMI_ROAM_PREAUTH_STATUS_CMDID command.
The host driver decides if the external authentication event is
received for preauth candidate or for initial connection by
checking the connected state information of the csr session.
When the authentication fails with the first candidate, the
target triggers the preauth start for the next candidate. This
happens till there are no candidates available to roam.
There could be a situation where the firmware sends preauth
event for candidate1 and before the supplicant could send the
external auth command to the host driver, the candidate1 preauth
timer could have expired and firmware sends the preauth start for
second candidate. After SAE is done with second candidate also,
the supplicant sends external auth event for second candidate. So
in this situation the firmware should decide to choose the
latest candidate. The host driver here is a mere passthrough and
doesn't maintain timer for the preauth event for each BSSID to
drop the expired candidate preauth events.
Change-Id: I799a05e55a59677dfc2ddf5b55ebc888ccfea03e
CRs-Fixed: 2507003
The Linux Coding Style frowns upon mixed-case names so rename
identifier tpAddBssParams to be compliant.
The Linux Coding Style enumerates a few special cases where typedefs
are useful, but stresses "NEVER EVER use a typedef unless you can
clearly match one of those rules." The tAddBssParams typedef does
not meet any of those criteria, so replace it (and the "tp" variant)
with a properly named struct.
Change-Id: Icf7fe19cfe6eb6fbac5689e3b5474d38c520b311
CRs-Fixed: 2506539
Firmware offloads WPA3 SAE authentication to host due to the
crypto library availability limitation. Once the roam candidate
selection is done in the firmware, firmware sends the
WMI_ROAM_PREAUTH_START_EVENTID. Once this event is received, the
host driver triggers the SAE.
Add support to offload the SAE authentication from firmware to
wpa_supplicant.
Change-Id: Ie3a9e731194e1edfcd9f33ef0d601767b9485d46
CRs-Fixed: 2490201
Create bss peer in lim_process_mlm_post_join_suspend_link
when sta connect, don't need pose message to wma queue.
Change-Id: I23325c9d41b68f67ea9903008521f026e46395c4
CRs-Fixed: 2505558
Currently driver passes sta_id through out the call for getting the TSM
stats. Although passed, the sta_id is not used anywhere in the call
stack. As part of removing the sta_id usage, this sta_id can also be
removed safely.
Remove the usage of sta_id in get TSM stats path.
Change-Id: I1efbb1bfdc8df84e9b6a71dcd5bd39ea93ced21a
CRs-Fixed: 2484701
Currently driver passes sta_id through out the call for getting the SNR
stats. Although passed, the sta_id is not used anywhere in the call
stack. As part of removing the sta_id usage, this sta_id can also be
removed safely.
Remove the usage of sta_id in get SNR stats path.
Change-Id: I39482d8f6d8e3bd32e940a85d5592dada8f0460b
CRs-Fixed: 2503956
Fix the compilation issues passing proper parameter to the function
wmi_unified_thermal_mitigation_param_cmd_send.
CRs-Fixed: 2501080
Change-Id: I9ce0038ef2844536612f0bf71314dbc214f354d9
Associating peer's phymode is not allowed to be highter
then sap's. If it is, set the peer phymode equal to sap
phymode.
Change-Id: Ia8152ce27fb8ddf2bbff5139d3b8d89c811d7ed0
CRs-Fixed: 2500383
In case bss peer add failure vdev state machine is in
substate WLAN_VDEV_SS_START_START_PROGRESS and thus
WLAN_VDEV_SM_EV_CONNECTION_FAIL will not be handled and thus vdev
SM will not move to init state and pe session is not deleted.
This lead to vdev ref leak for the ref taken by pe create session.
Fix this by sending WLAN_VDEV_SM_EV_START_REQ_FAIL event when
vdev SM is in WLAN_VDEV_SS_START_START_PROGRESS state and continue
cleanup.
Change-Id: I4c559333a6bd018e3382f9781883acf314434cf2
CRs-Fixed: 2502817
Because newest firmware codes already been changed, the previous
coex configure command are invalid. Firmware need host driver
to enable WMI_SERVICE_THREE_WAY_COEX_CONFIG_LEGACY service during
wlan init. Add a new parameter "gThreeWayCoexConfigLegacyEnable" to
initial config file. If this parameter value is zero,set coex
priorities command will return error.
Change-Id: Ief1617e2ba5363e276c55135198613a0e54b71d5
CRs-Fixed: 2482734
In case of failure in vdev stop response from FW, Along with
triggering SSR call the del_bss_response so that FW can clear
the bss peer.
Change-Id: Ibbf43f15796a9a13f922091d49fa6a22838aeaaf
CRs-Fixed: 2498497
Issue is : In case of STA + STA, Host sends BTM config enable on
both STA. This results assert in FW as at a time FW supports BTM
only on one vdev.
Following are the fix:
1. Send 11k offload and BTM config enable to fw irrespective of
roam reason. Enable of both while RSO start and disable of both
while RSO stop should be symmetric.
2. Currently, Host sends RSO_UPDATE_CONFIG for blacklisting case
if the vdev is in connected state irrespective of RSO start is
sent or not. Added check to make sure RSO_UPDATE_CONFIG should
not go if driver_disabled_roaming flag set.
Change-Id: Ib92089906a2e1690ec6181ac184bc008ccfbc928
CRs-Fixed: 2497813
rx mic error information is now posted to new HDD mic
error callback(hdd_rx_mic_error_ind) via .rx_mic_error
member in dp_ol_if_ops.
Cleanup the dead code left behind.
Change-Id: I32fd135506382c085755e25cab5af86824cea511
CRs-Fixed: 2488464
Currently btm offload command is sent to FW as part of RSO Start
for all type of roam req reason and btm offload disable command is
sent to the FW as part of RSO STOP. In case of STA+STA concurrency
case, while btm offload is enabled for the 2nd
STA after UPDATE_CFG sent for STA1, the FW asserts because it has btm
offload enabled for STA 1 while UPDATE_CFG and has not deconfigured
it yet. Send btm offload enable command as part of RSO Start in case
of roam_req->reason == REASON_CTX_INIT only to the FW so that it
configures btm for the currently enabled STA only in case of INIT
and re-configures for the second STA without assertion.
Change-Id: Ib146072c7cd0543ea82122702d6585d1d2a2e2d1
CRs-Fixed: 2493122
Currently, QDF_STATUS_SUCCESS is always sent for MGMT
Tx frames to packetdump.
Send the proper Tx status for MGMT Tx frames which is
mapped to packetdump tx status.
Change-Id: I7a780777910a5b9220ebb77cda1e0c4acd9f45b2
CRs-Fixed: 2490243
wma_roam_event_callback can get called in atomic context from
wma_wake_event_piggybacked for reason WMI_ROAM_REASON_HO_FAILED
which lead to acquiring of pm_ctx->qdf_conc_list_lock mutex lock
in atomic context.
To fix this post msg to scheduler thread to call the policy mgr
API in scheduler thread context
Change-Id: I6b75de64a33559b73a7edc73e1100cfb3a1f507d
CRs-Fixed: 2491147
This command is used to send OEM data binary blobs
from application/service to firmware.
Change-Id: I0b5d7dd5a030b70e59c8581fb51d99079b38385f
CRs-Fixed: 2477332
Driver has a stats infrastructure and all the stats related
commands are using this infrastructure and for this
target_if_mc_cp_stats_stats_event_handler is getting used.
Remove legacy implementation of stats event handler
wma_stats_event_handler and related APIs.
With this change remove unused structures also.
Change-Id: I9a892b5f7486a406654256fc2cc8177f2fafe790
CRs-Fixed: 2481937
Firmware sends roam event with reason WMI_ROAM_REASON_DEAUTH when
it receives deauth/disassoc from the peer and fails to roam.
The event also carries deauth/disassoc frame.
A new param "notif_params1" is defined to carry length of the
frame and a new TLV element "deauth_disassoc_frame" to carry
the frame.
Extract IEs from the frame when the event is received and
send them to kernel through cfg80211_disconnected().
Change-Id: I14610136e5e9758403e48264d04d1655e4466d3c
CRs-Fixed: 2481915
Driver has a stats infrastructure and all the stats related
commands are using this infrastructure.
Remove legacy implementation for wow stats related apis
as part of cleanup.
Change-Id: Ib06d5bf0e11c8340f459185d18c076c295f39df5
CRs-Fixed: 2481927
Driver has a stats infrastructure and all the stats related
commands are using this infrastructure.
Remove legacy implementation for get station stats api
as part of cleanup.
Change-Id: Iadc7fceccec32e7a27c29872fb13c03f79208965
CRs-Fixed: 2480770
