Iterate through the opclass table and fetch the opclass
details for the channel widths supported by the current
hardware mode.
CRs-Fixed: 3168892
Change-Id: I9b418999e3745529e3db5bae3a46569e0d1bdc02
&p_range->lowfreq, 'reg_assign_vars_with_range_vals' from incompatible
pointer type.
'low_limit_enum', 'high_limit_enum' may be used uninitialized.
'reg_is_val_within_range' defined but not used.
Change-Id: Id5ff2e0fa18555e4d27e955e6508bd23da280aff
CRs-Fixed: 3153499
WMI op extract_roam_event is also needed to extract roam event
of LFR2, so let it enabled for LFR2/3 both.
Due to struct roam_offload_roam_event is only defined for MCC,
add MCC specific macro CONN_MGR_ADV_FEATURE to protect it.
Change-Id: Ie9724ee578feb60ada30fe75ed3f155a2bbe77a9
CRs-Fixed: 3167557
The Multiple BSSID field (Bit 22) in Extended Capabilities indicates
whether MBSSID is supported or not. Skip MBSSID processing if the
field is NOT set in beacon.
Change-Id: Id18318587cb9d26fa6315202b5bbe98ef8870fdd
CRs-Fixed: 3160715
parsing
HW desc provides 'end_offset' which can be used as delimiter
to identify status buffer boundary
Change-Id: I265ab328b80615fd2386402f0ea3797d124b8f8f
CRs-Fixed: 3157554
When a packet s destined to ML STA from a legacy peer, use
the ML peer id to identify the primary link and redirect the
packet to primary vdev for Intra-BSS.
Change-Id: Id8e6fcc9e2dd638e6d923eef50f55325fa538c49
CRs-Fixed: 3169484
Puncture is one of 11be feature. Even 11be compile macro is defined,
Dut can start AP with non-11be mode. Regulatory component has no idea
whether it should consider puncture or not. Puncture should be a
configurable parameter from caller.
When updating channel state, puncture should be considered for 11BE
AP. is_create_punc_bitmap should be set in struct ch_params and pass
it to reg_get_5g_bonded_channel_state_for_pwrmode.
Change-Id: I96fb131f2df201a827ab7d98ca099a38b008e0d3
CRs-Fixed: 3160259
The maximum WBM2SW rings in whunt for MSL is 5 and
the same could be 4 in wlan code which will result
in wcov failure for MSL. Use a maximum of 5 WBM2SW
rings for HSP based on FW_SIM config flag to address
this failure.
Change-Id: I16770566710efeeea7acbb51f6710e7a996b5cac
CRs-Fixed: 3167050
Copy software image version, chip information,
pktlog json version and pdev id from the event received
from firmware.
Change-Id: I53c2fceee129fa69126ae8214fb652a744bfcbfa
CRs-Fixed: 3165004
For corrupt beacon frame, the memory allocated for
split_prof_start is getting allocated for split
profile case. But since there are no other nonTx
profile or new MBSSID element present afterwards,
Hence, added mem free to handle this scenario.
Change-Id: I6b93ae0be97d72264071d1ce99345f8c0c23f81d
CRs-Fixed: 3156909
Add support for new QCA nested attributes to pass the AFC channel
information as part of the external ACS request command,
EXTERNAL_ACS_EVENT_CHAN_INFO.
Change-Id: I9ab4b8bfce64ea31226dad90f39bee22086b94d9
CRs-Fixed: 3152230
For IGTK/BIGTK keyix, cipher table is not populated. Retrieve
cipher_type from key structure.
Change-Id: Ic61e66854f91317194ee90f64187fd2b787827b0
CRs-Fixed: 3163335
Currently we are sending DHCP and EAPOL connectivity
logs for Tx and Rx packets. but in case of DHCP
we are receiving DHCP DISC and DHCP REQ and
we are sending Tx status as TX_Fail.
So to fix issue ignore sending connectivity log in case
of Rx if packet type is DHCP DISC or DHCP REQ.
Change-Id: I688c375243cff0773bd8290e990d5106ff5b47ae
CRs-Fixed: 3164050
Parse the tqm bypass frames packet count and byte count and consider
them for stats updation in the vdev.
Change-Id: I644eb9819b8a68fbf9da2e2f2588c80dfaa61fa5
CRs-Fixed: 3163215
In ucfg_wlan_mgmt_rx_reo_sim_stop() when mgmt rx reo simulation
is in progress, wlan_mgmt_rx_reo_sim_start() is called
incorrectly instead of calling ucfg_wlan_mgmt_rx_reo_sim_stop().
Fix this by calling ucfg_wlan_mgmt_rx_reo_sim_stop() instead of
wlan_mgmt_rx_reo_sim_start() in ucfg_wlan_mgmt_rx_reo_sim_stop().
Change-Id: I906618fc87448cefae54bdcdf00c7f64217362fd
CRs-Fixed: 3154187
Consider the case where the AFC server response initially,
has only one 20 MHZ channel available for operation and AP is operating
on SP on that channel. In the next response, the AFC server response
advertises support for all UNII-5 and UNII-7 channel. In this case,
the AP VAP does not come up in the new channel chosen by ACS.
The super channel list is not being reset on every AFC response received
from the target. Also, if the current power mode is SP, and the target
power is also SP, reg_set_ap_pwr_and_update_chan_list does not the same
power mode configuration. Due to this, the current channel list and
super channel list are not updated, and therefore the VAP fails to come
up in the new channel chose by ACS.
To fix this issue, reset the super chan list on every AFC response
received and remove the check to prevent the same power mode setting
in reg_set_ap_pwr_and_update_chan_list.
Change-Id: I52f24038ef904e4f8ede6861b7e4a0cdcd9607b0
CRs-Fixed: 3154057
High CAC timeout is seen for weather and non-weather DFS channels.
This is due to the delay in 5.4 Kernel timers. There is 1 second delay
observed for every 60 seconds.
To fix this issue, replace qdf timers with HR timer for CAC timeout.
On CAC expiry, when VDEV UP is sent to FW, serialization timer is
cancelled. Since CAC expiry is processed in H/W interrupt context
(while using HR timers), no other timer cancellation is allowed.
Hence, process the CAC timer completion in work queue context to allow
other timer cancellations by the CAC thread.
Change-Id: I92c4662decbba27261448327abb16708d941d778
CRs-Fixed: 3142394
The regulatory pdev private object is used directly without a NULL pointer
check in the API reg_get_pwrmode_chan_list.
Add a NULL pointer check for the regulatory pdev private object to prevent
NULL pointer dereference.
Change-Id: If6f9daf5d88a8fb9fba1b184721ba10e96ad0e2e
CRs-Fixed: 3159429
Add empty definition for function in the case where the
6G feature is disabled. This fixes a compilation issue.
Change-Id: Idef12549cdfa9b3cb75b06fe04888e7c50356042
CRs-Fixed: 3162125
Add pdev open handler for management Rx reorder module.
This handler stores all the snapshot addresses to the pdev
private object of mgmt Rx REO module.
CRs-Fixed: 3111704
Change-Id: Iaf12b4edb568b2a32ff901ad5d0f0717b190906b
MLO HW link ids need not be continuous. Handle
discontinuous link id values at host.
CRs-Fixed: 3111570
Change-Id: I561cdabed8a6b621dba87c49832f5c1d1b194b9a
Validate the MLO HW link related info obtained from the global shared
memory arena of management Rx reorder feature.
CRs-Fixed: 3111549
Change-Id: I6fd7812dc49bfa8428b2ffbf66ae978592734bc0
Add the following APIs related MLO links in MLO manager.
1. Get number of active MLO links
2. Get valid MLO link bitmap
CRs-Fixed: 3154979
Change-Id: I49c544a5c73a9ce72305bbe83230a4566d909095
The API reg_get_ch_state_based_on_nol_flag() is a common API and in its
definition it calls the API
wlan_reg_get_5g_bonded_channel_state_for_pwrmode() which is defined for
the 6G specific macro CONFIG_REG_6G_PWRMODE. For non-6G callers, this
function is not defined and will lead to implicit declaration compilation
error.
Add a non-6G version of the API
wlan_reg_get_5g_bonded_channel_state_for_pwrmode() so that, it can be
called in reg_get_ch_state_based_on_nol_flag() even for non-6G PFs.
Change-Id: I810af65c7580f9a5dbfb2df25530dd95261e2a80
CRs-Fixed: 3161629
The API reg_get_ch_state_based_on_nol_flag() calls the function
wlan_reg_get_5g_bonded_channel_state_for_pwrmode() which is part of the
header wlan_reg_services_api.h. This header is conditionally included
using the macro CONFIG_AFC_SUPPORT which is not enabled for all the PFs.
Remove the condition header file inclusion as
reg_get_ch_state_based_on_nol_flag() is a common API for all PFs.
Change-Id: I3f6cc301474648fdd6a2937421ee0421a0788856
CRs-Fixed: 3161629
Currently, host supports max 2 number of AKMs in connect req.
Add support for max 5 number of AKMs in connect req from
userspace.
Change-Id: I889124257c374092128e92f0f1eca1e1d0711f49
CRs-Fixed: 3151412
