Add changes to send roam scan mode over RSO start/stop/update_cfg
from connection manager. Update the roaming params and roam scan
params to new structure.
Refine send_roam_scan_offload_mode_cmd_tlv().
Change-Id: I6adce2e8a24ece93a079032d0e66760393fcdccd
CRs-Fixed: 2766023
Add RSO logic to send roam trigger from target if along with
some optimization to move old logic in ROAM_OFFLOAD_V1.
Change-Id: I38e7fb4f8873328097df7e3a25d6c709f8d69b33
CRs-Fixed: 2765155
Add support to send WMI_RSSI_CHANGE_THRESHOLD command to firmware
in connection manager.
Change-Id: I97d4b8f8fc0e938ede0e61d44eb8ffbcbb0fb4ff
CRs-Fixed: 2761043
Add new code to implement below functions for connection manager
roam part:
And below two RSO command related process:
ROAM_SCAN_OFFLOAD_STOP
ROAM_SCAN_OFFLOAD_UPDATE_CFG
Change-Id: I378b969ddae77fff49ad1d4d8ce21764b292e5ac
CRs-Fixed: 2753011
WMI handler is registered for twt_session_stats event.
Upon wmi event twt session parameters are extracted and
cached in peer mc_cp_stats. UMAC APIs are provided to
retrieve TWT session parameters from north bound
interface(hdd) using twt peer's mac_addr/session dialog_id
CRs-Fixed: 2730732
Change-Id: I8ce38ac6be97e844e26e03751c6d6cca981b82b4
With the newly introduced BLM enhancement, APs may get enlisted
and sent to FW for (re)assoc restraint. However, the FW side
AP restraint is only required when LFR3 is enabled.
With LFR2, no FW side AP (re)assoc restraint is required and all
actions will be done within driver code.
Use LFR3 specific conditional macro to enclose all the code
needed for sending reject AP list to FW.
Change-Id: I9a8bc0e25bc4b319bf1841324ef1b711f0659093
CRs-Fixed: 2751791
Add connection manager changes to send roam scan offload init
deinit. Add new enum roam_offload_init_flags to fill the roam
init/deinit flags, 4-way handshake offload, bmiss skip full scan
flags at connection manager instead of getting the ini and filling
at target if.
Change-Id: I558e868efd341b508d3df76c8d6ab90eac512432
CRs-Fixed: 2745585
Add macro ROAM_OFFLOAD_V1 for new code and implement below functions
for connection manager roam part:
csr_handle_roam_state_change() roam offload state related handler.
Filling WMI_ROAM_SCAN_RSSI_THRESHOLD cmd parameters related process.
Change-Id: I0351155ca5a3d68ade6568c7527c5708582ccf1a
CRs-Fixed: 2730826
NAN protocol runs in firmware and controlled by framework.
Framework configures multiple NAN discovery params while enabling
NAN. Framework configurations would be based on the framework
constraints or realtime scenarios like resource(memory/power/..)
consumption. But some of these params might need to be controlled
explicitly based on the usage.
NAN DW is one such parameter, which is configured as 4 seconds
when the device is in sync role and the screen is off. But
for some usecases, this param might have to be 512ms always
irrespective of screen off/on for some targets. Add an ini param
"nan_feature_config" to set a bit to indicate firmware whether to
honor framework configured DW value or the firmware default value.
Send the vdev param on NAN supported vdev by setting the "bit 0"
to indicate firmware to allow framework configured DW value.
If this bit is not set, firmware shall consider its default value.
Change-Id: I0476bca2bbe676beccfff207f5b4ea31e89031e2
CRs-Fixed: 2721970
Enable compilation of the connection manager roam files with
Kbuild changes.
Add new API to store and retrieve the firmware scan channels at
mlme. Also add initial support to post SET_PCL command through
lim, so that it is not sent before ROAM init command.
Add changes to restrict connection of the 2nd STA to
channels on the other band of the 1st STA connected band.
This is done by filling only the allowed band channels in
the scan filters for the 2nd STA connection. If only
1 STA is active, it is allowed to connect on any band.
Add header gaurds for missed header files:
wlan_cm_tgt_if_tx_api.h
target_if_cm_roam_offload.h
Change-Id: Id2bce12b9663ed635ea46164169b088461aab870
CRs-Fixed: 2720341
Add new connection manager API to send vdev pcl command for
sta + sta roaming per vdev. For vdev pcl command, the weight of
the 1st sta connected band will be set to 0.
Add connection manager roam API files for TX ops,
connection manager target if wrapper to send the vdev
pcl command to wmi. Introduce new API to get dual sta
roaming support and save it in cm roam public struct.
Change-Id: I56a7475b0b9865e969917ec05a117f206f198111
CRs-Fixed: 2712346
Update multicast and broadcast rx packet count on
receiving wmi update stats event from firmware by
fetching the peer stats from DP layer.
Change-Id: I0befdbe952aa4e773bbe072affaf698819b3a80f
CRs-Fixed: 2709871
Update return type of target_if_nan_event_flush_cb to return
QDF_STATUS to match scheduler_msg_process_fn_t.
Change-Id: I2f0380edeb21a1c6016358725abab39fdc741466
CRs-fixed: 2698302
Currently there is a check to validate if the station is in
associated state or not in the hdd lost link cp stats info cb,
There is a race condition where if the disconnection happens
from ap in that case the callback gets invoked before the
connection state in the station context gets updated and thus
the rssi on disconnect is not updated.
To address above issue remove the check to validate the station
state and update the rssi on disconnect irrespective of the
state of the connection.
Change-Id: I9cc6a08cdf0a1081adfde7a9423a665bc977cffc
CRs-Fixed: 2678667
gEnablePowerSaveOffload is confusing, so change it to
gAdvancedPowerSaveMode.
Value 0: Disable advanced power save
Value 1: Enable advanced power save
Change-Id: Ib5593ef31eedacdc232ffbad183974e2cd847e83
CRs-Fixed: 2676664
Add ini config required for FTM time sync feature.
"enable_time_sync_ftm"- ini to enable/disable the feature.
"time_sync_ftm_mode" - ini to configure the burst/aggregated mode.
In burst mode the offset derived for each RTT frame is sent by
firmware, in aggregated mode only one offset is sent by firmware.
"time_sync_ftm_role" - ini to configure slave(STA)/master(SAP) role.
Change-Id: I6a06d6fdc4c7556c32ab2d28f1cbaa936b98a85b
CRs-Fixed: 2618654
Register tx and rx ops to send packet capture mode command and
to receive mgmt offload handler for packet capture component.
Change-Id: I70da00feff29399b98c5916eec17e26b62285db3
CRs-Fixed: 2619321
Add support for the following NAN messages in kmsg:-
1. NAN enable status
2. NAN, NDP match events
3. NDP channel info.
etc.
Change-Id: Icbf8f4ed05a7bd181a076d526dd2e01d70be6b05
CRs-Fixed: 2618835
Send vdev param command to FW for STA vdev to set the packet
capture mode. Send the command only if packet capture support
is enabled.
Change-Id: Ifed2431882b1f7d2869771e812daa5bcd5dc17e9
CRs-Fixed: 2619314
Add the function to parse the FTM timesync start/stop and offset
events received from target and populate them in ftm timsync
priv vdev structure.
Change-Id: Ibdcf97bb0a04fc6490c6bd2c26701036df92c5d4
CRs-Fixed: 2618646
This patchset adds the FTM TIME SYNC component in
target_if to register the ftm time sync wmi events/cmds.
Change-Id: I4ea14266a912c9d261a67809556774860b5ddab1
CRs-Fixed: 2617055
Add support to customize DSCP-to-UP map table and send the
customized map values to FW to update its corresponding
map table.
Change-Id: Ibe9704a90468c898dd2e60fdf83a271152f654ce
CRs-Fixed: 2616247
Currently as part of tdls enable link, If the peer is buff
capable or tdls uapsd is enabled in INI. UAPSD is enabled in
FW. Avoid sending this command to FW as it effects the behavior
with AP.
Change-Id: Idc023cb9de3ab63e7643815d473fe0efa98069b9
CRs-Fixed: 2528208
Reject AP list which is maintained by the blacklist manager
has to be sent to the FW for roaming case scenarios, as
the blacklist, and rssi reject APs should not be preferred
in the reassociation.
Change-Id: I58bf90e17653dde2a5042780ba7d57fa3115d63a
CRs-Fixed: 2461230
BLM:- Blacklist Manager
Add the basic infrastructure such as target-if, tgt, init,
deinit, ini files, core and main files for the new component
Blacklist Manager.
Change-Id: I624a779ee0dd6be7cb26a911af0aefd426ca9bff
CRs-Fixed: 2460602
Implement the interface to transfer the info between
host driver and firmware about the ap which has interop
issues with the DUT. It is detected by firmware and
forwarded to user sapce for persistent storage. And
user space configs these APs to firmware when the DUT
starts up next time.
CRs-Fixed: 2425202
Change-Id: I2e828d521f0e04862a01fa1c90626f51b7f65796
WMI_STA_PS_PARAM_INACTIVITY_TIME and
WMI_STA_PS_PARAM_MAX_RESET_ITO_COUNT_ON_TIM_NO_TXRX
need to be sent as WMI_STA_POWERSAVE_PARAM_CMDID param IDs.
Thus use pmo_tgt_send_vdev_sta_ps_param instead of
pmo_tgt_vdev_update_param_req in appropriate locations.
Change-Id: Ie9438cd88540a9bbcaf120b3d0a32d355f85002d
CRs-fixed: 2457998
Any new param_id added to target_if_pmo_send_vdev_update_param_req
should be added to wmi_tag_vdev_set_cmd to be tagged for runtime PM
feature so that it will not invoke runtime PM get which may result
resume right after suspend (WOW_ENABLE).
Change-Id: Ifa154b38ec91599023e30a37b7fcfef88f5f0491
CRs-fixed: 2451994
Send idle roam trigger monitor command to firmware based on
the SET SUSPEND mode command received from the user space.
The set suspend mode value sent will be used by firmware as
one of the parameters in determining if the device is in
idle state. When set suspend mode is 1, device is not in
idle state else the device is considered idle if idle state
data packet count, idle rssi, inactivity time criteria are met.
Add changes to send the suspend mode value over the wmi
command WMI_IDLE_TRIGGER_MONITOR_CMDID.
Change-Id: Ia4531fdab140334dbb830e0d7486db07bbdfc7e8
CRs-Fixed: 2436221
In USB devices even if the driver returns an error from bus_suspend,
still the kernel/platform goes into suspend as any error from USB
bus_suspend is ignored.
During suspend, if WoW or suspend was NACked by FW, we should not
send WMI_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID, WMI_PDEV_RESUME_CMDID to disable
WoW or resume device (in the next system resume)
Add new PMO API to get target suspend state and use it to check if
device should be resumed.
Change-Id: Ic6be05f4f2d36ffe174774b6cd55c6da6b1ea1b8
CRs-Fixed: 2421591
Currently there is no support to configure ito repeat
count when driver enters into wow mode.
Add support to configure ito repeat count with ini
gItoRepeatCount when driver enters into wow mode.
CRs-fixed: 2419137
Change-Id: I62d7e7df12342e9743c26e0147851347214a9ce7
Per the Linux Kernel coding style, as enforced by the kernel
checkpatch script, pointers should not be explicitly compared to
NULL. Therefore within target_if replace any such comparisons with
logical operations performed on the pointer itself.
Change-Id: Id9b5185713b91b67ddf1d965a6c7e52508558d82
CRs-Fixed: 2418397
Currently there is no support to configure the inactivity
timeout when driver goes to wow mode or when driver resumes
from wow mode.
Add support for PMO component to configure the wow mode
inactivity timeout with ini g_wow_data_inactivity_timeout
when driver enters into wow mode and when driver resumes
from wow mode add support to configure the inactivity
timeout for non wow mode with ini gDataInactivityTimeout.
CRs-fixed: 2412866
Change-Id: I0672f22a5dfec870e5e67b23058db2729b9a0848
NAN Datapath implementation allows more than one concurrent
NDI's to be active at the same time. But this isn't supported
if there is a higher priority incoming connection such as
STA. Add modules that check for unsupported NDI concurrency
and initiates termination of all NDP's on it.
Add modules that check and disable unsupported NDI concurrency.
Change-Id: I6ad9afbfc41beda1d1c8f31bf58a8ea70027f5ca
CRs-Fixed: 2407215
