Use AST override feature to send out multicast packet in
4 address format. Pass per packet peer_id from osif layer.
Change-Id: Ic86120169c89e7972caa3cc8c967de72670314d0
CRs-Fixed: 2775051
- Added data structure for wds ext peer
- Enhanced DP peer structure to maintain
wds ext peer data structure, which inturn
maintain pointer to osif device.
- Enhanced DP vdev structure to maintain feature
configuration, which will be updated during vdev
creation when feature is flag is set at control
psoc.
- Enhanced cdp_vdev_param_type and cdp_config_param_t
to set wds ext configuration into DP vdev
- Enhanced cdp_cmn_ops structure and corresponding
call back definitons to get peer id, which will
be saved in osif private structure and to set
wds ext peer rx.
- Enhanced cdp_ctrl_ops to send event to control
path when 1st 4 address frame is received from
backhaul.
Change-Id: Ide0ea54e7b2d480ad646fb84b6e4e3108930f986
CRs-Fixed: 2773492
1. Add flag to support hlos id override feature in dp vdev
2. Update tid from nbuf->priority in dp_tx_send
3. Update tid to nbuf->priority in dp_rx_process
Change-Id: I66e8d77733a667f3f60b77e0d7bb444f7c5ad93d
As part of the VoW IGMP improvements, which deals with
conversion of igmp packets to unicast packets, the
following changes are done when the new feature is enabled:
1. IGMP/MLD packets with special addresses (addresses not
part of any multicast group) will be converted to all
existing clients of the AP. These packets will be
directly fed to igmp multicast to unicast conversion
module.
2. The IGMP/MLD packets with group specific addresses will
first go to multicast enhancement module, where they
will be allowed to pass and will be converted to unicast.
3. The new feature will be enabled only when multicast
enhancement feature is enabled, which will be ensured
at the configuration level.
FR : 61063
Change-Id: I2fd5a67766c806432fbe1a12cb9654a3600100f5
Add support to update the count of number of Punctured Preamble
PPDU's transmitted by the AP.
Change-Id: Id85a490e9e80566e639f48190a96d3107c6e5c61
CRs-fixed: 2755288
This change will add a build flag support to MSCS wherein
the functions will be called based on the status of the flag
created. This flag will be enabled by default.
Change-Id: I1c234c710d3b37f534ed2df7b37343cbd65ab930
CRs-Fixed: 2757257
Add INI to modify the HW checksum capability advertisement.
Add hook to update enable/disable of HW checksum for vdev.
Change-Id: Idd0bad1d39c8411c7b4ef19483aa2c75a756791b
CRs-Fixed: 2732099
This change will acquire MSCS parameters from the
MSCS request sent by the STA and provide it to the
data path which will later use it for building flow
database.
Change-Id: I972154792c682527f8df04de693077188726e8da
CRs-Fixed: 2669386
Peer wlanstats context was accessed directly from
PPDU cookie, with this approach the cookie pointer
may become stale if peer goes for deletion
Hence access the wlanstats context using CDP API
with stats context protection
CRs-Fixed: 2740261
Change-Id: I54c785325f8852ad422f05527b98ebca6e4d6cf0
Add support to retrieve per PPDU phy tx duration without response time.
Add support to retrieve per User phy tx duration for MU-MIMO and OFDMA.
These metrics are useful for ATF stats feature. Stats processing done
only if atf stats flag is set.
CRs-Fixed: 2709102
Change-Id: I90db41aa45843808e07343a80750c154abbde9cd
Add WMI support for WMI_TWT_SESSION_STATS_EVENTID. This event
contains stats for a given TWT session.
Change-Id: I01d5f7b30da803ee713a14c1d1124b8af7161bca
CRs-Fixed: 2609951
copying mu data info is done inside schedule command status tlv
and handling based on completion status is added.
Change-Id: I2792d754a4fa3e2992d68f569c9ce40be8ff02e2
New flag is added in PPDU user, this flag gets updated
on processing the user of a PPDU desc
Change-Id: Ib778b08833392bfd5651a83c2c1131f1d1ce3ea8
CRs-Fixed: 2738431
Currently, per-user information in Tx PPDU completion is allocated for
37 users though FW may send information for fewer number of users. In
new scheme, FW provides number of users in USERS_INFO TLV and host can
allocate the per-user struct based on this number. This can save memory
while processing each completion message.
CRs-Fixed: 2730923
Change-Id: If04fd664a1ef6e77e8eb44c5d2bd1fa89fcaba72
Currently there is a single INI item tcp_udp_checksumoffload to enable
or disable this feature for all the adapters. In some cases, we want to
be able to enable this feature selectively for NAN mode.
Add nan_tcp_udp_checksumoffload ini item to enable or disable checksum
offload feature specifically for NAN mode. If
nan_tcp_udp_checksumoffload is 'true' and tcp_udp_checksumoffload is
false, hardware checksum offload will be enabled only for the NAN
adapter and not for other adapters.
CRs-Fixed: 2693638
Change-Id: I6e255ce68ddc7b01ebdefe4e5e8d2c985388fefe
Configure the client as isolated peer if part of isolation
list while creating/associating the node or adding the peer
to the isolation list.
Do not forward the packets to and from clients in isolation
list instead accelerate to upper stack.
CRs-Fixed: 2689868
Change-Id: I67fd4dee0fb76c993746cdd66c70c241d407239a
Set OL_TXRX_NUM_LOCAL_PEER_IDS to WLAN_MAX_CLIENTS_ALLOWED
if WLAN_MAX_CLIENTS_ALLOWED is defined.
Change-Id: Ifb5c6ab15e791f92aa8503537e624195cf3fad6d
CRs-Fixed: 2694492
This mode is supported through hw_mode_id 7. A special mode for
IPQ8074 platform alone to bring up single pdev alone on 2G mode.
FW would advertise the mode 7 support through the WMI service
ready message and this mode will be the default mode for AP-HK10 alone.
Added preferred_hw_mode and target_pdev_id into dp structures so that
they can be used to configure the dp rings for this particular mode.
Also changed the lmac_id to target_pdev_id mapping for mode 7.
Change-Id: I3aae46fea13132eebaf7d37cff68ef517253d229
In case the bus is in low power mode, the register writes (followed by a
memory barrier) may take a long time (~4ms). This can cause the caller
to block till the PCIe write is completed. Thus, even though PCI
writes are posted, it can still block the caller.
Hence, in case the bus is in low power mode (not in M0), or not in high
throughput scenarios, queue the register write in a workqueue. The
register write will happen in the delayed work context. In other cases,
i.e ,when the bus is not in low power mode or in high thoughput
scenarios, do the register writes in caller context.
Change-Id: Idf218e4581545bc6ac67b91d0f70d495387ca90e
CRs-Fixed: 2602029
Add doppler and spatial reuse in ppdu descriptor to be able to use it on
HE information for tx capture
Change-Id: Id87a692a89d00c64929624c22c2efc27bc873e43
Change set 2 of ctrl_ops APIs to replace pdev, vdev and peer
dp handles with pdev_id, vdev_id and peer mac address
along with dp soc handle
Change-Id: I3f180c9c360d564f0b229b447074ad23b7c0a737
Add new parameters for converging multiple set/get
APIs into common psoc/pdev/vdev/peer set/get APIs.
Change-Id: I0802dea028c9e935ef899169cf7d86f2dc7632bc
Change set 1 of the ctrl_ops APIs to replace pdev, vdev and peer
dp handles with pdev_id, vdev_id and peer mac address
along with dp soc handle
Change-Id: Iedf6dea2215d3d04b2212c71c8ec8c7328c559e8
CFR information extracted from PPDU status TLVs is already stored in
HAL ppdu structure. Extract the same and copy it to CDP ppdu structure.
This is delivered to subscribers through a WDI event, similar to PPDU
stats.
Change-Id: I4315626c7f79f85b75b8d1b9e1e5caf8d65abed9
CRs-Fixed: 2593416
Change cmn_ops APIs to replace pdev, vdev and peer
dp handles with pdev_id, vdev_id and peer mac address
along with dp soc handle
Change-Id: I5716a87cad56b1dfe8dd56f193bbb6ff923a6af1
as we are overriding bar ppdu information, we need bar start/end
timestamp and duration.
added resp_type, mprot_type, rts_success and rts_failure in
cdp completion user.
Change-Id: I53c215e948fad8d079e1d4c40ec07d34aff1fefe
Remove pdev and vdev control path handles from data path.
Instead send pdev_id and vdev_id along with opaque soc
handle in ol_if_ops.
Change-Id: I6ee083f07e464f283da0d70ada70a4e10e18e1b2
Currently the cdp apis are given pdev/vdev/peer
handle as its arguments, which is directly
accessed in those APIs. This can cause a
race-condition in access of the respective
handles, if it has been deleted in parallel.
Hence as a part of cdp convergence, pass only
the pdev/vdev id or peer mac address, which will be
used to get the respective handles, and hence
avoiding the unwanted access of the handles, if
it has been deleted.
Converged misc_ops
- tx_non_std
- get_opmode
- get_tx_ack_stats
- set_ibss_vdev_heart_beat_timer
- hl_tdls_flag_reset
- set_wisa_mode
- txrx_post_data_stall_event
- update_mac_id
- pkt_log_init
- pkt_log_con_service
- get_num_rx_contexts
- set_wmm_param
- flush_rx_frames
- bad_peer_txctl_set_setting
- bad_peer_txctl_update_threshold
- txrx_data_stall_cb_register
- txrx_data_stall_cb_deregister
- vdev_set_driver_del_ack_enable
- get_intra_bss_fwd_pkts_count
- mark_first_wakeup_packet
- register_pktdump_cb
- unregister_pktdump_cb
- pdev_reset_driver_del_ack
- runtime_suspend
- runtime_resume
CRs-Fixed: 2539811
Change-Id: I3080df033d6411d7078a322224b914bda2fddc0e
When a particular vdev is deleted, the corresponding rx
packets which have been queued to the rx thread are not
flushed. Hence when such packets are submitted to the
network stack, the dev for this skb will be invalid,
since we have already freed the adapter.
Flush out the packets in the rx thread queues, before
deleting the vdev.
CRs-Fixed: 2543392
Change-Id: I2490d0f5ce965f62152613a17a59232521ca058f
Add the soc context for ol_txrx,
The soc layer is used to hold the ol_pdev context.
CRs-Fixed: 2539807
Change-Id: I751ad61de55db9d86624b8b5e18b0981ffb0338d
In cases where one of the interfaces is a P2P-GO and
IPA has been enabled, the P2P connection establishment
fails.
When IPA is enabled, the REO destination is changed to REO4
which can be reaped only by IPA module. But in case of P2P-GO
interface in operation, this change in configuration causes
all the RX packets to be stalled due to incorrect REO configuration.
Hence, to avoid this case, do not change the REO dest config
when the interface subtype is P2P.
CRs-Fixed: 2498315
Change-Id: Ie9f01c3b353c7c0503e1541d6c79c2f47c9782f3
Process smart antenna fields from tlv
HTT_PPDU_STATS_USR_COMPLTN_COMMON_TLV in tx
completion path and export it to tx_completion.
Change-Id: If14e711b0aee8e583fd329f3c3915904649ffe47
CRs-Fixed: 2491429
Since tx_monitor mode and rx_monitor mode consume signficant MIPS
when enabled on a per-peer basis, new requirement is to enable such
functionality on a per-peer basis. New CDP APIs are added to set these
per-peer parameters.
CRs-Fixed: 2494471
Change-Id: Ib44845ec98481cc4df36c30f47335522e5274568
