This commit enables support for SuiteB roaming for SHA384.
Based on the WPA3 SuiteB roam service capability advertisement
received from Firmware, we enable the support in Host.
Change-Id: Iab4e6bfc9c8ba7d604c2720c8cb848fce40dd6b4
CRs-Fixed: 2685975
With specific AP(s), FW needs to perform FT initial mobility
association instead of FT roaming for deauth roam trigger.
This ini is used to configure "FT roaming for deauth roam trigger"
behavior from the HOST.
Change-Id: Id754a21f7ac2c330019055646f79c79db3e0c52c
CRs-Fixed: 2665882
Remove instances of CFG_COUNTRY_CODE and country_code from
wlan_mlme_reg struct.
Remove redundant country code APIs.
This change is needed because the country code is no longer
stored in CFG file, and subsequently, there is no need for
CFG_COUNTRY_CODE.
Change-Id: Ia4b3b40d0dccfde696352967f2902dfba344a445
CRs-Fixed: 2634079
Add support to provide the channel weightage of
DFS channels so that the weight can be configured
and the user can control whether they are allowed
to be selected for the SAP.
Change-Id: I53a22a0059d56aa8fca66215fed1ed0588db7db5
CRs-Fixed: 2676919
The roam sequence in LFR-3.0 is roam scan start notification
from firmware followed by roam start indication and then
roam synch,roam synch frame events. Roam start is sent
after candidate selection and host driver will disable
queues when roam start is received.
But for emergency roam trigger, firmware sends roam start
indication directly without notifying roam scan start to disable
data path queues immediately after deauth received from the AP.
So roam start is received before roam scan is started at firmware
and before candidate selection is done.
After roam start notification, host sends scan abort for all scan
on vdev by setting scan command request type to
WMI_SCN_STOP_VAP_ALL. This results in roam scan getting aborted at
firmare in emergency deauth roaming case and roaming fails.
Define new vdev id value based on which the scan module will
abort only host triggered scans setting the request type to
WMI_SCN_STOP_HOST_VAP_ALL in the scan request.
Change-Id: Ie8b005285973461f654329e1b2dc1a45205331f5
CRs-Fixed: 2644323
Add sanity check for mlme_obj in wlan_mlme_update_oce_flags to avoid
illegal memory access when mlme_obj is not valid.
Change-Id: I7dfd72cc704d3f9c11241fb2217f0b2ab7eda3d3
CRs-Fixed: 2669262
Currently there is no ini to control the rrm support on
SAP.
Add a new ini to enable/disable rrm on SAP.
Change-Id: Idef8da807bc5f8e2b4a1d61997824006e78b0cf6
CRs-Fixed: 2658926
Currently, the driver trims the channel list with
the PCL if external acs policy ini is set, and
if the channels are unsafe then that can lead
to 0 channels and the SAP can fail.
Fix is to check whether the force SAP start ini
is set and override the channel.
Change-Id: If245bf27deda0f6022343d7a175520fdd92d106b
CRs-Fixed: 2667742
Currently, only broadcast disassociation is supported
and deauth is sent in a unicast manner.
With peer delete all support, HDD sends a single call
to PE for broadcast deauth request. PE module sends a
single broadcast deauth frame and on TX completion,
calls vdev_mgr_peer_delete_all_send. This issues the
new WMI_VDEV_DELETE_ALL_PEER_CMDID to FW to cleanup
peers entries corresponding to VDEV ID and also flush
TIDS internally.
On receiving the peer delete all response, target_if
cleans object manager entries and datapath cleans up.
But PEER unmap is done iterating through all peer entries
individually. After this a single eSAP_STA_DISASSOC_EVENT
is received in HDD signalling the completion of broadcast
deauth procedure.
Change-Id: I928461606154380eef21a02cc7306921ceb9e16e
CRs-Fixed: 2585005
Made the default value to advertise trigger frame padding
duration as 16 us so as to honor HE MAC capabilities sent by FW
Change-Id: I1bf75965f1b9b46d61c94997273621a6e9de46c1
CRs-Fixed: 2667623
With Change-Id: I02f207cdde9d8fb68cd91fab07572baa9e7ac50d,
Ini roam_trigger_bitmap is only initialized when LFR3 enabled.
In LFR2 case, without disconnect, roam_trigger_bitmap is set as
0, vdev roame state is stuck in ROAM_DEINIT for 0 bitmap, can't
switch to ROAM_INIT and ROAM_RSO_STARTED any more, can't enable
roam scan offload in F/W, so no roam scan and better AP event
is reported to host from F/W even RSSI low or beacon miss
happens.
change-Id: I95cb6c892a67816cf47c8dada9b542ae6aefe7f3
CRs-Fixed: 2662880
When set_pmksa command is received from userspace, the internal
pmk table is updated with the new bssid entry and the pmk is saved
to the session. Additionally this update triggers an RSO update
command to the firmware which causes the use of stale pmk for
single pmkid case, in which the BSS capability of SAE single pmk
will be known only after parsing the beacon/probe received in the
roam synch indication.
So donot send RSO update on receiving set pmksa command.
Change-Id: I25419fbc3061ab963ccf3228b3681c83773a7963
CRs-Fixed: 2659055
Add INI - gActionOUIReconnAssocTimeout to configure driver
to do:
1. Driver will not send deauth to the AP after association timeout.
2. Reconnect to same BSS again if the last association failure
is association response timeout.
Default="00E04C 00 01"
The change fixes IOT issue with certain AP which doesn't
response first association request frame sometime. But the AP
would response second association request.
Change-Id: I9f7b8d14aaaaa97f08856c8b62e49b145db3ac91
CRs-Fixed: 2653877
Control path use the data path variables to detect PN replay
and also modify the same.
Thus move the PN replay detect logic in objmgr peer in control path.
Change-Id: I8d1cd4b86eac3f6a7343c4616e398579bc4932ae
CRs-Fixed: 2658077
Currently the driver fails the ACS process
if no channel is found suitable for SAP by
ACS and thus hotspot cannot be enabled.
Fix is to force SAP to come up on some
default channel, this behaviour would
be controlled via an ini to that customers
can choose whether to opt for this behaviour
or not.
Change-Id: I8a63cf0c5d42802e33f4ad67a33d148a4da54d2a
CRs-Fixed: 2658297
Currently the driver allows roaming to the BSSID
which it is already connected, which can lead to
many unexpected behaviour, for eg. if the SAP
to which the DUT is connected turns off, then the
DUT would try to roam to other BSSID of the same
SSID, and in case the SAP turns on back in time,
then the DUT would re-associate to the same BSSID.
Now if the subnet may change, and since the DHCP
does not happen again in roaming, it would then
lead to NUD failure.
Fix is to introduce an ini to allow/disallow
roaming to the same BSSID.
Change-Id: Ibd04fcd7384c0987db5bb6dae1a26ee077456290
CRs-Fixed: 2634860
Channel congestion score is not well bucketized, as we only have 0-25,
26-50, 51-75, 76-100, so small change will not give different score.
while channel congestion weight is high: 25.
Increase channel congestion slots num from 4 to 8 as following.
0-12% 13-25% 26-38% 39-50% 51-63% 64-75% 76-88% 87-100%
100% 90% 80% 70% 50% 25% 10% 5%
2500 2250 2000 1750 1250 625 250 125
Change-Id: I4fc2d8a5f0f64c5fce9fe5ec8f16c3e8e9665a60
CRs-Fixed: 2655110
Remove max_tx_power from wlan_mlme_power struct
and ini_tx_power from lim_max_tx_pwr_attr struct
and all their instances.
Change-Id: I982a15b71b64d368b623128e04f09a8f3bf4f5ec
CRs-Fixed: 2645922
Increase the roam failure reason string buffer size to
60 from 50.
Also add reason string for roam failure reason.
Change-Id: I42f4332463e4063aa0dee39631ca31965db12b62
CRs-Fixed: 2647260
Introduce an INI "ap_tx_pwr_scoring" to indicate firmware about ap tx
power weightage so that firmware can use ap tx power weightage to
calculate candidate AP's score.
Change-Id: I8831c571162f044f4ae204ef0edfc59942f36837
CRs-Fixed: 2647115
Add pointer str1 NULL check before use in mlme_acs_parse_weight_list()
in case user side has wrong configuration.
Change-Id: I7a1552e417a7571d138a2c1c526aa2f9d0015529
CRs-Fixed: 2642567
Currently QDF_MAX_NUM_CHAN/POLICY_MGR_MAX_CHANNEL_LIST aren't aligned with
NUM_CHANNELS, these unalignment may cause some potential OOB access.
So replace QDF_MAX_NUM_CHAN/POLICY_MGR_MAX_CHANNEL_LIST with NUM_CHANNELS
to keep unified.
Change-Id: Ib6c81a3979f2fd29ba1ec678f018a6704b599385
CRs-Fixed: 2644066
Add host driver support for MCS 12/13, a Q-Q PHY feature.
The following changes are being introduced as a part of this
- Advertisement of the MCS 12/13 using the QCN IE
- Interaction between the Host and the FW regarding the target and
peer capabilities for the new features introduced.
- The new data structures and variables to populate and use the feature
capability
- Routines to add and parse the IE.
Change-Id: I2b91a271d30b1230ef7bb14ee08d0b9da2706db4
CRs-Fixed: 2610277
As each bit of INI "sta_disable_roam" represents an interface on which
if the connection is present, disable station roaming.
Hence to use all the bits of "sta_disable_roam" INI, change type to
UINT.
Change-Id: Ife4bb31acf89ddbe744bdad376a8a6f5a733b92c
CRs-Fixed: 2647036
In wlan_mlme_clear_sae_single_pmk_info, driver clears sae_single_pmk
locally while processing del/flush pmk command from supplicant.
Driver should clear entry for sae_single_pmk mlme priv objects.
Fix is to clear entry for sae_single_pmk in mlme priv objects.
Change-Id: Iee71a1a86e293a1028e9b4003d5a48c72d19a8f4
CRs-Fixed: 2636662
The max ini params for mws_coex_pcc_channel_avoid_delay and
mws_coex_scc_channel_avoid_delay are set to be at 0xFF. This max value
doesnot correspond with the actual max value needed by the firmware.
Change the max value to include upto 0xFFFFFFFF
Change-Id: If88d7866c584abf43a41b0c6b9f63b21a0a4a2f2
CRs-Fixed: 2632517
Use INI "sta_disable_roam" to disable roaming on STA interface if
connection on other interfaces ex. p2p, ndp comes up. Each bit of
the INI "sta_disable_roam" represents an interface.
ex. LFR3_STA_ROAM_DISABLE_BY_P2P BIT(0)
LFR3_STA_ROAM_DISABLE_BY_NAN BIT(1)
As INI "sta_disable_roam" is generic for all the interfaces, cleanup
for INI "p2p_disable_roam" done.
Change-Id: Icd05a97c640ca07978d9960a33de036ed6fe38df
CRs-Fixed: 2637555
Currently MCS parameters are not getting correctly in
wiphy which results in incorrect capabilities for iw list
command output.
To resolve above issue, update MCS parameters correctly in
wiphy band capabilities.
CRs-Fixed: 2633314
Change-Id: I830ad50aa4842bd2a79c97ed7b11b82c35148ff0
Currently the roam failure reason string size is 40 bytes.
Change this to 50 bytes to avoid truncation in some failure
cases.
Change-Id: I6c90e31fc792078354e98c7a5c61ffd5583469c3
CRs-Fixed: 2637901
Presently vdev delete is sent to firmware 1st and the object manager
vdev delete is deleted after all the references are released.
With this change the vdev delete is sent to firmware when all the
references are released and the vdev delete is sent to firmware via
the object manager vdev delete notification.
Change-Id: I67bea0d2b2a0d2d9eb4602e5d0b8bbdcafdd4d26
CRs-Fixed: 2618278
Add ini support for DFS Channel Ageout Time, the time upto which
DFS channel information such as beacon found is remembered.
This ini is used to set the ageout timer value from host to FW.
If not set, FW will disable ageout time.
This value is sent as a WMI_PDEV_PARAM_SET_DFS_CHAN_AGEOUT_TIME
as part of WMI_PDEV_SET_PARAM_CMDID.
Change-Id: I99553fa87a4025f03c52b4b387a414ba06c2c457
CRs-Fixed: 2625996
ignore_fw_reg_offload_ind is used to ignore regdb offload
indication from FW and regulatory is treated as non offload.
Change-Id: Ic9a47fe3ec49cf1fa9cbf7ab166decdc4ece0511
CRs-Fixed: 2630994
Introduce ini for roaming_triggers to enable/disable specific
roaming triggers. This will be the master ini to control roaming
triggers. If this ini is set to zero, roaming will not be enabled
on the sta interface unless its enabled via vendor command.
A new roaming trigger - Sta kickout roaming is introduced in
firmware, include this bit support also in the ini.
The value of this ini will be sent over the wmi command
WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID during RSO start.
Reset this value to 0 during RSO stop if RSO stop is due to
disconnect or roam synch failure.
Change-Id: I02f207cdde9d8fb68cd91fab07572baa9e7ac50d
CRs-Fixed: 2631712
Introduce an INI "enable_roam_reason_vsie" to inidicate fw to
include/exculde roam reason vsie in reassoc frame
Change-Id: I4d2a44812d8b11a19b0d7d31eb31c826aaeda79d
CRs-Fixed: 2627472
Currently, if roaming happens roam reason is not sent to AP. AP will
not able to know why roaming happened. As roaming is offloaded to
firmware, firmware will include roam reason vsie based on driver
indication by vdev param
WMI_VDEV_PARAM_ENABLE_DISABLE_ROAM_REASON_VSIE based on
below conditions:
Parse the QCA attribute CONFIG_ROAM_REASON to control
inclusion/exculsion of roam reason vsie dynamically. Vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION can control roam
reason vsie inclusion using QCA atrribute CONFIG_ROAM_REASON.
Different operations required to implement this feature can be
specified in QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON, so driver parses
CONFIG_ROAM_REASON, updates enable_roam_reason_vsie and indicates to
firmware by updating vdev param.
a.) If Userspace wants the firmware to include roam reason in reassoc
frame, it can send QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON with
value 1 and driver will update enable_roam_reason_vsie to 1.
Driver will update vdev parameter
WMI_VDEV_PARAM_ENABLE_DISABLE_ROAM_REASON_VSIE, so that firmware
can include roam reason vsie in reassoc frame during roaming.
b.) If this command is not issued, the default behavior of the
firmware is not to include err reason code in beacon report
response. Driver will send default value of
enable_roam_reason_vsie to firmware which is 0.
c.) The userspace requests the firmware to stop roam reason vsie
reporting when roam reason is not required for AP anymore. If
userspace doesn't want the roam reason inclusion, userspace can
send QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON with value 0 and
driver will update enable_roam_reason_vsie and notify firmware to
exclude roam reason.
If userspace requests the driver to get the status of
enable_roam_reason_vsie , to check whether firmware includes roam
reason vsie or not, driver will fill CONFIG_ROAM_REASON attribute and
will update to userspace.
Change-Id: I063c822e99fd6908bd4188b429ffa6a2031cee5d
CRs-Fixed: 2624713
Clear sae_single_pmk info while processing del/flush pmk command
from supplicant, if required.
Change-Id: Idd974822ef0426461cd9971e54d8244d64b246b5
CRs-Fixed: 2616036
Requirement is to allow station to just keeps only one
PMK1 and PMKID1 which gets derived while first connection
and re-use it for roaming to other AP which has some
specific VSIE.
To support this feature, STA should Set new flag in 11i
params during RSO start/update when initial connection is
completed based on the VSIE in AP beacon/probe response
frame. This flag will allow fw to roam to AP(s) which has
VSIE with single PMK.
Update PMK info in RSO start command with
sae_single_pmk info if initial connection is completed
with AP contains VSIE.
Change-Id: I839b48da48f92f24444e69405d87560186d7f986
CRs-Fixed: 2616029
Requirement is to allow station to just keeps only one
PMK1 and PMKID1 which gets derived while first connection
and re-use it for roaming to other AP which has some
specific VSIE.
To support this feature, STA should:
1. Set new flag in 11i params during RSO start/update when
initial connection is completed based on the VSIE in AP
beacon/probe response frame. This flag will allow fw to roam
to AP(s) which has VSIE with single PMK.
2. STA should dynamically enable this feature if below
vendor specific IE on AP’s Beacon or Probe Response at
the first connection:
Category Data
Type 0xDD
Length 0x05
OUI 0x00 40 96
Type 0x03
Data Don’t care
(EX, 0x05)
Maintain a separate pmk information structure to support sae
roaming using single pmk.
Change-Id: I0aac7659cecd4d8aaff86c9715e512cf46f22615
CRs-Fixed: 2616035
Optimize logs after connect complete i.e roam offload params
and tdls state etc.
Change-Id: I5df7eb236ef1c7369f4d996c4f0eda7225652f12
CRs-Fixed: 2627694
Userspace expects the assoc request IEs of a disconnected station
to derive 11kv capabilities. Send the same in STA_INFO as part
of remote station info.
Change-Id: Iab5f39de833cd06e814e83f0149a0d21caf59b9f
CRs-Fixed: 2624922
Introduce a compile time flag SAE_SINGLE_PMK and new INI
"sae_same_pmk_feature_enabled" to enable/disable SAE
Roaming with same PMK/PMKID feature.
Change-Id: Ifca8ec8bcf6e9a2f1d8409b35390bfee0033bd30
CRs-Fixed: 2616025
During CU and low rssi based roam triggers, consider AP as roam candidate
only if its roam score is better than connected AP score by at least
min_roam_score_delta.
User configures this candidate minimum roam score delta value using
"min_roam_score_delta" INI. User can set candidate minimum score delta
value between 0 to 10000 and default value is 1850.
Firmware will trigger roaming only if roam score of candidate AP is
greater than "min_roam_score_delta" & "roam_score_delta" values of
connected AP.
Change-Id: I180e769b5629aa405dbd89ed73e39e228adf92db
CRS-Fixed: 2614117
Currently, host driver sends disconnect reason code as UNSPECIFIED
to kernel in most of the disconnection scenarios. Correct the same
to send proper reason code received from peer in case of peer
initiated disconnections.
Introduce new reason codes for internal disconnections and assign
proper reason code for each possible disconnect scenario.
Change-Id: I99bf4573b59dc810e0a1529fcd48061d10acae4e
CRs-Fixed: 2622310
