Refactor the hdd_vdev_create() API to move device mode
based VDEV config to a new API.
The new API calls required configuration functions
based on the device mode.
Change-Id: I54c5412577b70d92652cb16fcfb10e4d69e6f6fd
CRs-Fixed: 3445149
Currently thermal level can be got from upper layer only
for FW thermal mgmt offload case. Per the requirement,
refine the code to support it for thermal non-offload
case as well.
Similar to offload thermal mitigation, add TX_OFF and
shutdown two states for non-offload case. Host will fully
stop TX traffic in TX_OFF state and target will trigger
shutdown when temperature come to the range of shutdown.
Per above requirement, add below four INI to configure
thermal temperature threshold value as need for TX off
and target shutdown.
gThermalTempMinLevel4
gThermalTempMaxLevel4
gThermalTempMinLevel5
gThermalTempMaxLevel5
Change-Id: I40d097ab8a5801052553ad7adedd38be475c7669
CRs-Fixed: 3413165
Currently smart tx module is not included in gFwDebugModuleLoglevel
ini as default.
Add the smart tx module with log level 1 in gFwDebugModuleLoglevel
ini as default.
CRs-Fixed: 3396120
Change-Id: I09e49745dfc17926d1f59b6bbe7a99ae09e36a16
Currently host sends many pdev/vdev set param
commands separately to firmware from hdd.
Combine multiple pdev/vdev set params and
send to WMI to reduce number of transactions.
Also replace target wmi pdev/vdev params with host wmi
pdev/vdev params to fix existing broken layering
violation.
Change-Id: Ib76f5bd5f582a2c67486f6773ff6fd486b3d84cf
CRs-Fixed: 3333732
Currently host sends tx chain mask and rx chain mask
pdev set params separately to firmware.
Combine these tx_rx chain mask pdev set params,send to WMI
to reduce number of transactions.
Also replace target wmi pdev/vdev params with host wmi
pdev/vdev params to fix existing broken layering
violation.
Change-Id: I6bd27b4bc99cbe44e6bdca2a8d55050a49719673
CRs-Fixed: 3333635
The kernel-doc script identified a multitude of documentation issues
in components/fw_offload, so fix them.
Change-Id: I9c5b3f561d74ac433bd7f8c47cab737af9af3ecb
CRs-Fixed: 3357050
The feature raises a pulses at specified interval in TSF time domain.
The pulses can be used to determine driver level latency between hosts
as they are operating in same TSF time domain.
Add ini "g_tsf_accuracy_configs" to configure parameters for TSF accuracy
feature to customize GPIO pins and interval.
Change-Id: I49609d5beba8043ac2ecc086e97b01d1e0b2d3f6
CRs-Fixed: 3277992
Add ini support to configure traffic shaping for COEX
i.e. coex_tput_shaping_enable.Host sends this INI to
Firmware via WMI_COEX_CONFIG_ENABLE_TPUT_SHAPING.
Based on this enabled value, FW will do power save with AP
when BT page scan is enabled.
The default behaviour is to do a free run without notifying
a power save to the AP during the BT Page scan.
Change-Id: I4934c98911b66c7c834899ad7cdc72063e9c5153
CRs-Fixed: 3066980
Previously when chains of BT and WLAN 2.4 GHz are separated,
hybrid mode will be used for BTC. Now adding fixed FDD mode
to fulfill different BTC scenarios.
Change-Id: I3a4d6919319f0f66e6b816566f24f4ac11b2c669
CRs-Fixed: 3244045
In order to debug HMT SAP, need to enable FW AP PS module logs.
Hence, change the default ini value for gFwDebugModuleLoglevel.
Change-Id: I5fc9f22b751f5e9c6b43592ec298462a0abd489f
CRs-Fixed: 3192480
Initialize struct cm_roam_values_copy to avoid using uninitialized
parameters in wlan_cm_roam_cfg_set_value().
Initialize struct pdev_params to zero to avoid using uninitialized
parameters in wmi_unified_pdev_param_send().
Change-Id: I820db09840431487f1756695a0562f8a794f549f
CRs-Fixed: 3187194
Previously elna_bypass is of type bool, which check for
elna_bypass enabled or disabled with en_dis
Change en_dis to elna_mode of enum extlna_mode
to support extra mode of firmware_default
Change-Id: I12dfe3a07e04b102562b11c8235d56bd3e2a7059
CRs-Fixed: 3169266
Enable pci gen switch feature by default since the ini will not take
effect unless the feature flag is enabled in FW too.
Change-Id: I4170ddc84e994829e1f8144d3a90deddfe71f280
CRs-Fixed: 3162231
Enable source port learning for SAP to add AST entry for the
remote stations with next hop. The SAP should use 4-address
frame format for the remote destinations.
Add support to handle data packets for WDS destination.
Change-Id: I6002e6dd9c9bb2c7b2e4f85bf06156dbb7feebee
CRs-Fixed: 2997812
Currently when get temperature is queried, both
gThermalMitigationEnable ini and WMI_SERVICE_THERM_THROT service caps are
checked in the driver.
gThermalMitigationEnable ini means the thermal throttling will be done
by driver if enabled and will be done by FW if disabled.
So, set this ini as 0 by default in the driver as thermal throttling
is done by FW and check only WMI_SERVICE_THERM_THROT service while
get temperature is queried.
CRs-Fixed: 3139693
Change-Id: I28e2b6cfca6ea7bf60d81045ba267e019143f3a8
Rename files with blacklist/whitelist to denylist/whitelist.
Rename files with blm to dlm.
Change-Id: Ief7ce0a797f74460c9708f8d2dd440412af5b7eb
CRs-Fixed: 3099864
Replace blacklist/whitelist with denylist/allowlist in
qcacld3.0. and replace blm with dlm.
Change-Id: I9ba61dde3b3ea008ca3777448d1f8dab83d33ec1
CRs-Fixed: 3091211
Add "gEnableUpdateScramSeed" ini support to send
WMI_PDEV_PARAM_EN_UPDATE_SCRAM_SEED command to firmware
to enable OFDM scrambler seed.
Change-Id: Ie5c244a7ea418eec0af1f576e8521804ee85a665
CRs-Fixed: 3106348
Enable more WoW logging modules to help with debugging by changing ini
gFwDebugWowModuleLoglevel=1,3,5,3,18,1,19,3,31,1,36,1,57,3.
Change-Id: Ib42e16188c2572d04971be0e28836797286faeac
CRs-Fixed: 3042611
Add support for sending WMI_REQUEST_THERMAL_STATS_CMDID
to request for the thermal stats via vendor cmd:
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS
This vendor cmd can either be used to clear the thermal
stats or to request for the thermal stats.
Added ini gThermalStatsTempOffset, which can
configure thermal temperature offset value for capturing
thermal stats in thermal range such as Thermal STATS
starts capturing from temperature threshold to temperature
threshold + offset.
If this ini is set to 0, then the events are disabled.
Also, add support for the FW event where the requested
thermal stats are sent in FW event
WMI_THERM_THROT_STATS_EVENTID().
The following attributes are sent in the events for every
level:
STATS_MIN_TEMPERATURE
STATS_MAX_TEMPERATURE
STATS_DWELL_TIME
STATS_TEMP_LEVEL_COUNTER
Change-Id: If8acdeec5bde33be346332ccaf39d78d0151203d
CRs-Fixed: 3016818
Enable the firmware module WLAN_MODULE_WPM with error log level
in wow mode by adding default values in the ini gFwDebugWowModuleLoglevel.
Change-Id: I53a729bde6cfb6d8141864472718a2d8da9efead
CRs-Fixed: 3022434
The purpose of the multicast Domain Name System (mDNS) is to resolve
host names to IP addresses within small networks that do not include
a local name server.
It utilizes essentially the same programming interfaces, packet formats
and operating semantics as the unicast DNS, and the advantage is zero
configuration service while no need for central or global server.
Based on mDNS, the DNS-SD (Service Discovery) allows clients to discover
a named list of services by type in a specified domain using standard
DNS queries.
Here, we provide the ability to advertise the available services by
responding to mDNS queries.
Change-Id: Id2a0468d49237c21062cfd1988e34903658cdad9
CRs-Fixed: 3008549
At present, duplicated thermal level change events are reported
on different mac with different pdev id from target. To report
the lowest pdev id's thermal level to avoid confusing the user.
Change-Id: Ia1f497ba1a1e0af946b87924de80b9fd39fe95e8
CRs-Fixed: 2976437
Add gConfigBleScanCoexPolicy which can be used to
control performance of ble scan case.
’0’ to place more emphasis on BLE Scan results
‘1’ to place more emphasis on WLAN performance
Change-Id: I46c735d8695523d14f6372bc5e47d1d1f51589ae
CRs-Fixed: 2935051
As part of WiFi ini clean-up FR, the ini parameter gEnableLPRx,
is identified as it is no longer used. Hence it can be deprecated,
and all instances of the config CFG_LPRx is removed.
Change-Id: I77f8f6839534c9a79cb3c7414582a5f31b87c561
CRs-Fixed: 2896027
Currently, there are two ini option 0/1 to disable/enable ILP
profiles in HW.
Extend this option upto 3 where
0 indicates disable
1 indicates perf settings
2 indicates max power saving
3 indicates balanced settings
Change-Id: Iff41b92b84309a670e2ad301ee72fb3caaba3df3
CRs-Fixed: 2886526
HW assist is a FW feature and it is enabled by default. But there is
no provision to disable/enable this feature based on requirement.
To address this, add INI param to enable/disable HW assist feature
in FW.
Change-Id: Icdc4a842be4d5c6991a785ee270f61ba87fcfe79
CRs-Fixed: 2841346
Add ini to set init chain mode for BTC, default value should
be set to the same as macro WLAN_COEX_BTC_CHAIN_MODE_UNSETTLED
that means no need to send init chain mode for BTC to firmware
in wma_vdev_pre_start() process.
Change-Id: I3051a7f8a0c708c7df40d1b95b46e0bfa6892f6c
CRs-Fixed: 2837173
cds_get_context() function already takes care of logging the
caller function name in case of any error.
Hence there is no need to add the error log again.
Getting rid of these unnecessary logs reduces driver memory footprint.
Change-Id: I5bf676c79e9e12a797dc6792ee8014fb30b0dff3
CRs-Fixed: 2821005
The SHO feature is used to offload beacon/probe response to HW.
So a new vdev param is required to enable/disable this feature.
Change-Id: I83d71d63485dee8d3433bf967a7feb56c1039f93
CRs-Fixed: 2815270
Add an INI to configure the wow-mode logging config.
So that,the fw would use this bitmap for logging when it
is in wow mode.
Change-Id: Ib2fbd0c5c9cc573b2f5b12dcdf06682c16550cb2
CRs-Fixed: 2810372
Handle firmware thermal stats event and populate the thermal
information to upper layer with vendor command event.
Change-Id: I83286367ab542c08a205a7636f3d03189b0500e5
CRs-Fixed: 2786623
gOclCfg is no longer supported and is being overwritten by
FW init config. Thus, remove gOclCfg ini from code.
Change-Id: Idf4d5280043a47650a68dc2159c386d94b0be5e9
CRs-Fixed: 2791392
There is customer requirement that once wifi chip overheat,
we should switch the tx chain mask to 1X1 to cool down the
chip instead of halting the tx completely.
Add new INI gThermalMgmtAction to configure thermal mgmt action
with default 0. The valid thermal mgmt action INI value is defined
as enum thermal_mgmt_action_code. To set it to 3 -
THERMAL_MGMT_ACTION_CHAINSCALING to meet customer requirement.
Change-Id: I88b1237fae1f476ad9ff0e7b5a469ec314a42bf9
CRs-Fixed: 2765289
For older targets thermal mitigation is supported for the apps.
In moselle there a new processor wpps on which firmware runs,
this commit adds the support for the thermal client wpps.
Change-Id: I89896dce808807486ef56b90812369f3d5f4b270
CRs-Fixed: 2757566
ILP is a new hardware block which is used for PCIe powersave but
this can effect the throughput.
So to isolate the throughput issues, add ini param to
enable/disable this ILP hardware block using the ini configuration.
Change-Id: I19825af8598bbc2623542256e873367c2f3d29bd
CRs-Fixed: 2756587
Update default value for gFwDebugModuleLoglevel to get more logs
to debug firmware issues.
Change-Id: I388f7af62b00b6af5d963e2c6f2dec90389cca18
CRs-Fixed: 2722193
Currently these params are sent to fw from hdd. By design, this
should be done by fwol component. Add fwol APIs to achieve this.
Change-Id: Ifcc67fe15e76a32c28819267b0639edae1032093
CRs-Fixed: 2665749
