Support mld self roam between DBS(2 GHz+5/6 GHz) and HBS(5 GHz+6 GHz).
Change high rssi config.
Change-Id: Icb65f26509848a09fe46bf01154a0f42efa073f2
CRs-Fixed: 3416549
Extend WMI_ROAM_STATS_EVENTID event information for
requirement of:
1.Roam trigger related information, include timestamp,
trigger reason, trigger condition, abort reason,
scan type, roam status and fail reason.
2.Roam scan related information, include scan channel
number, dwell type, max dwell time of each channel
and total scan time.
3.all types of roam related frame information, include
timestamp and successful or failed status for Preauth,
Reassoc, EAPOL-M1/M2/M3/M4.
Cache roam information in wlan driver, when qca vendor
cmd of QCA_NL80211_VENDOR_SUBCMD_ROAM_STATS get roam
information, driver send all the cached information to
user space.
change-Id: Ic5e1120b51c20c103100833b4296002c5939b021
CRs-Fixed: 3389269
Componentized code should be adhering to the coding standard.
However struct roam_offload_synch_ind has a large number of
camelcase members.
To fix this replace camel case members with snake_case.
Change-Id: If866379d8f01cc0e932ea391d586575de4af9163
CRs-Fixed: 3383579
Even primary interface is configured, if dual STA policy is
STA_POLICY_UNBIASED, MCC is disallowed for both roaming and connect.
Change-Id: I6e26fdcdc930eb116771abfe310811c6534be09f
CRs-Fixed: 3396425
In case of 1x MLO roaming, 4 way handshake is offloaded to supplicant
and link vdev is down in FW. Host has to bring up link vdev post
set key installation.
Add handling in host for following:
- During roam sync indication handle only assoc link.
- Save reassoc response and link information.
- After keys are installed bring up link vdev by
queueing connect req on link vdev.
- Enable roaming after all links are up.
Change-Id: I9c0722f88e950ba05ec3dd7f44883bedf568f97d
CRs-Fixed: 3287316
Firmware sends the roam scan info tlv to driver during roaming.
Currently, in this tlv, firmware fills scan type as (0-3) and
driver log this as "PARTIAL", "FULL", "NO SCAN" and "Higher Band"
But with new requirement, idle roaming shall only roam to higher band
(2.4 GHz < 5 GHz < 6 GHz) than current band.
1. If current band is 2.4 GHz, it cannot roam to 2.4 GHz.
It can roam to 5 GHz and 6 GHz.
2. If current band is 5 GHz, it cannot roam to 2.4 GHz and 5 GHz.
It can roam to 6 GHz.
So, to add this requirement, firmware introduces new scan type 4 for
which driver need to log.
Change-Id: I80d1c47a434da5009aed4cab08c6eae91bda5b0e
CRs-Fixed: 3379468
In api cm_roam_stats_print_11kv_info(), neighbor report
logging was not supported.
Add support for Neighbor report connectivity logging
through api cm_roam_neigh_rpt_req_event() for Neighbor
report request event and api cm_roam_neigh_rpt_resp_event()
for Neighbor report response event.
Change-Id: If9d93584d4030f76b5175d361dfd34fce3b5b5b1
CRs-Fixed: 3370797
The kernel-doc script identified a multitude of documentation issues
in components/umac, so fix them.
Change-Id: If30358cb83e90348e410cfea163353f2dd26b3fa
CRs-Fixed: 3360814
The wpa_supplicant disables the BTM cap in extcap IE whenever
the MBO AP is not PMF capable, or if the btm_disable conf is set.
In current host driver design, the BTM offload is disabled only for
the MBO+non-PMF case. Therefore, add change to disable the btm offload
config if the BTM CAP is not present in the (re)assoc request as this
is determined based on intersection of peer and self cap.
Change-Id: I2fdc1010bccf5ce23f4ab2177aed6c374f7a510f
CRs-Fixed: 3369096
Currently host sends two ndp inactivity timeout
params to firmware one after the other.
Combine these two ndp inactivity timeout vdev
set params and send to WMI to reduce number of
transactions.
Also replace target wmi pdev/vdev params with host wmi
pdev/vdev params to fix existing broken layering
violation.
Change-Id: Icaeca85f2aa074f04d268b819fe86f4b7879c25b
CRs-Fixed: 3333749
While scheduler thread init and enable RSO after MLO connected,
wpa_supplicant deinit RSO for MLO disconnect.
At last, RSO is enabled on host, RSO is deinited on F/W side,
no event for RSO stop cmd, vdev0 disconnect not finished for
cm_disconnect_continue_after_rso_stop isn't called.
To fix it, hold cm_rso_lock in cm_roam_state_change to make sure RSO
operation atomic. RSO operation of one thread not preemptied by RSO
operation of another thread. RSO init and enable process of connect thread
isn't preemptied by RSO deinit of another thread, no host F/W RSO out of
sync issue will happen.
Remove ucfg_user_space_enable_disable_rso from hdd_init_station_mode since
cm_rso_lock is held before created.
Change-Id: I3010895d26a622c2a14960847089a63736598b7c
CRs-Fixed: 3365417
Pass the akm explicitly in the external auth
request to the userspace since there are many
SAE AKM suites.
Change-Id: Ifef8657f7ef75b402aa670813eba6adc5ab9853a
CRs-Fixed: 3355395
This is applicable only when the roaming happens from 2.4 GHz/5 GHz
to 6 GHz AP.
The value is used to check if the 6 GHz AP to which we are roaming
(from 2.4 GHz/ 5 GHz) is better than current AP in terms of RSSI.
This checking is disabled if the value is set to zero.
Change-Id: I77f1183e1fd704dfa153841e669a20c9e75d0fe7
CRs-Fixed: 3353346
In WoW mode, roam auth event may comes before roam start event, so CM
isn't in ROAMING state at that time, can't assume ROAMING state.
Change-Id: Ibf868db1ca0f9863d4beae4c83227cf04fe55adb
CRs-Fixed: 3357115
For SAE-EXT-KEY AKM with group-21 pwe, the PMK
length is 64bytes. Therefore, increase the max
size of the PMK to 64bytes in host to facilitate
PMK storage and PMK offloads.
Change-Id: I777a31acd56073d6a0312c47d95fe7d155b06fc6
CRs-Fixed: 3353102
During the roam scan, if there are no desired APs found in the partial
frequency list, an immediate full scan on all the supported frequencies
is initiated as a fallback. This would include the 6 GHz PSC
frequencies by default.
This attribute allow that behavior to be modified to include PSCs only
if 6 GHz use has been detected in the environment.
Change-Id: I6dc380419f14b920737fd87cd9a487c28364563b
CRs-Fixed: 3351697
User can include/exclude the frequencies in roam full scan that
were already scanned by the previous partial scan, using the new
vendor attribute introduced as part of roam vendor command.
Host sends the configured value to firmware.
As per current implementation of roam scan, if there are no APs
found during partial scan, immediately a full scan will be
initiated as a fallback. This includes all channels that were
already scanned as part of partial scan.
This attribute controls the optimization, to exclude all channels
which are already scanned as part of partial scan.
Change-Id: Icd6381b4daadcfe32dabda131ae92e2e32f07f1d
CRs-Fixed: 3343657
Clean up code for sme_get_empty_scan_refresh_period_global() and
sme_get_neighbor_scan_refresh_period() apis
and replace it with ucfg api.
Change-Id: Iaa511024467f45dc408da3db202b25f9b5276453
CRs-Fixed: 3335898
Clean up code for sme_get_roam_opportunistic_scan_threshold_diff() and
sme_get_roam_scan_home_away_time() apis and replace it with ucfg api.
Change-Id: I7de3bf3faff990cbf667cb8106044a33f16f3a46
CRs-Fixed: 3335898
Clean up code for sme_get_wes_mode(), sme_get_is_lfr_feature_enabled()
and sme_get_is_ft_feature_enabled() apis and
replace it with ucfg api.
Change-Id: I7715ba361264fcb2c0c93d8d073813538347dd31
CRs-Fixed: 3335898
Clean up code for sme_get_neighbor_scan_max_chan_time() and
sme_get_neighbor_scan_max_chan_time() apis and replace it with ucfg api.
Change-Id: I8a9de18f22e352ed8c64f415fd0455f64227a857
CRs-Fixed: 3335898
Clean up code for sme_get_roam_rssi_diff() and
sme_get_is_ese_feature_enabled() apis and replace it with ucfg api.
Change-Id: I226efbcf8ecd44b08684a3e17e2db987c169946d
CRs-Fixed: 3335898
Clean up code for sme_get_empty_scan_refresh_period() and
sme_get_neighbor_scan_min_chan_time() apis and
replace it with ucfg api.
Change-Id: I372fcbcf4f96af2c642a5fe93c0f8e2ce98174ea
CRs-Fixed: 3335898
Clean up the code for sme_get_neighbor_lookup_rssi_threshold() and
sme_get_roam_rescan_rssi_diff() apis and
replace it with ucfg api.
Change-Id: Idc7503eaa316d68dc05aba8345970ace7bc8ad45
CRs-Fixed: 3335898
Clean up code for sme_get_valid_channels() and
sme_get_roam_intra_band() apis and
replace it with ucfg api.
Change-Id: Ic2f07e2193186d1e1ac81f6e5909417c10ab9c89
CRs-Fixed: 3335898
When dual sta connected as SBS mode instead of dbs mode, driver didn't set
pcl per vdev, so dual sta had same PCL in firmware, MCC may happened after
roaming.
Fix:
1. Host pass roaming MCC disallow flag to F/W by checking primary vdev id.
2. For platform SBS supported, when doing dbs or sbs, send PCL from table
to F/W directly, allow SCC and SBS<->DBS roaming, don't limit to intra
band, only avoid mcc case if no primary vdev.
3. Use policy_mgr_concurrent_sta_on_different_mac to replace
policy_mgr_concurrent_sta_doing_dbs, add logic to consider SBS when set
PCL to F/W.
4. Change dual sta PCL table to remove mcc channels.
5. When STA channel switch, also update PCL to F/W.
6. For roaming case, do vdev level PCL update for all sta after connection
update in policy mgr, or wrong PCL is got.
Change-Id: I631c84c96da2bba4011b69e4c076db174205c874
CRs-Fixed: 3336768
User can configure roam hand-off delay value using the new vendor
attribute introduced as part roam vendor command.
This change gets the configured value and sends it to firmware.
And firmware delays the roam Hand-off (in msec) by the specified
duration to receive pending RX frames from the current BSS.
Change-Id: Ic328c077cba06532ee8ffed12cde072c816b92e0
CRs-Fixed: 3329964
When firmware attempts roaming to an MLO AP, it tries to find
the complete ML info(all links info) either through ML probe
response or beacons from all the links. It forwards all link
beacons(or ML probe response) to host as part of roam sync
indication through roam sync frame event.
Add support to fetch both link beacons and add them to scan db.
If firmware sends ML probe response, generate link probe response
as well and add it to the scan db.
The link scan result can be used in link connect in case of
hybrid roaming like OWE, 1x,..
Change-Id: Ic8457a5630441d6fd3faeb4791c79422db787f94
CRs-Fixed: 3335225
Add changes to enhance the debugs in the RSO path,
to identify the current pmk stored in the rso config.
Also, restrict the PMK dumps to a minimum size of 2.
Change-Id: I6e89afed45f5d43b45508ae43b59400a6e24e5ef
CRs-Fixed: 3312677
Host driver sends ROAM enable to firmware by setting the
vdev param WMI_VDEV_PARAM_ROAM_FW_OFFLOAD and the internal
state is moved from WLAN_ROAM_DEINIT to WLAN_ROAM_INIT.
Then host driver can send ROAM SCAN OFFLOAD enable and firmware
honors it. Firmware drops the RSO enable command if ROAM enable
vdev param is not sent. Host tracks RSO enable through the states
WLAN_ROAM_RSO_ENABLED/WLAN_ROAMING_IN_PROG/
WLAN_ROAM_SYNCH_IN_PROG/WLAN_MLO_ROAM_SYNCH_IN_PROG.
Have different APIs to track ROAM enable and RSO enable which can
help to cleanup the corresponding params/states.
It's observed that ROAM enable/disable vdev param is not sent
to firmware properly when RSO is stopped in some other path
than disconnect (e.g. SAP concurrency, fast_roaming_disable
through wpa_supplicant). Check if the roam state is INIT and
send ROAM DISABLE to firmware while disconnect.
Change-Id: I1074c8f93e21f02086dfbcfae61fa6deb91c7d9d
CRs-Fixed: 3305563
Replace all occurrences of
wlan_reg_get_channel_state_for_freq with
wlan_reg_get_channel_state_for_pwrmode and use extra
parameter as REG_CURRENT_PWR_MODE.
Change-Id: I7f7e4e700091918eeebc87ccbbc85ececdd9bf52
CRs-Fixed: 3145011
Roam trigger bitmap is configured to enable few specific
triggers when SETNCHOMODE command is issued. But if disconnect
happens without NCHO disable, then the roam_trigger_bitmap
per vdev doesn't reflect the ini configuration. This causes
some roam triggers not getting triggered.
Reset per vdev roam trigger configuration.
Change-Id: I3dc008a58a2a20c4f0820fe43aa4b6406ba8dd2a
CRs-Fixed: 3300488
When roam from SAE legacy to SAE MLO, pre-auth TA is MLD address,
while peer AP expects link address, pre-auth fails.
Parse transmit address field from firmware roam_preauth_start_event and
include it when send NL80211_EXTERNAL_AUTH_START to wpa supplicant for
SAE roaming cases.
If transmit address is all zeros, wpa_supplicant will not do ML sae
auth, use MLD address as TA.
If transmit address is not zeros, wpa_supplicant will do ML sae auth,
use 'transmit address' as TA.
Since self peer is created with mld address, when roam from legacy to
MLO, try to get peer by mld address during pre-auth tx since bss peer
absent, or TX fails for no peer.
Change-Id: I99ed846e94165bfe01e1d1e8c620f035751c7056
CRs-Fixed: 3289987
Rename wlan_cm_ese_populate_addtional_ies() to fix misspelling in the
name: addtional ==> additional
Change-Id: I3a5528d09804628cc665ee882ced3af2581b0f34
CRs-Fixed: 3281750
Send MLO Roam config to target, including:
support_link_num: Configure max number of link mlo connection supports.
support_link_band: Configure the band bitmap of mlo connection supports
Bit 0: 2.4 GHz band support if 1
Bit 1: 5 GHz band support if 1
Bit 2: 6 GHz band support if 1
Change-Id: Id59fc93cc271266ff794702d997ffc5113de5bc1
CRs-Fixed: 3273012
After roam sync is recevied the phymode will be updated for bss peer.
For MLO roaming use link address and channel to find the bss peer and
update the phymode.
Change-Id: Ic181fdb73ceeb8dfb980a4121a7569b12d3361dd
CRs-Fixed: 3280059
SAE authentication frames during roaming should be cached and
printed after roam scan done print. This support is not present
in diag logging.
Enable SAE auth frame caching for diag logging.
Change-Id: I205bd2fd1c91253d1e6aaf3361857baf67ccd6fd
CRs-Fixed: 3254216
Add a flag to indicate assoc req is used for this roaming,
don't treat assoc req as reassoc req.
Change-Id: I3a13985b6b173892fbe281668d07f7179d1c364c
CRs-Fixed: 3274314
On some projects, LFR3 roaming is not supported due to
limitation of FW memory, thus, add support for WPA3 LFR2
roaming.
Change-Id: I80888049a243c0d37e08377d89a6aa44e75a8850
CRs-Fixed: 2973554
In whitelist roaming, the roam offload event is sent
for an BSSID with different SSID, however host driver
copies the connected bssid in the external auth event
to the userspace. This leads to preauth failure.
Cache the ssid from the beacon received as part of the
roam frame event before every roam auth offload event
and use that ssid for external auth events to userspace.
Change-Id: I634992baf0c98054897707aaf3b1265e17d46f04
CRs-Fixed: 3262859
Reorder the BTM logging according to the below
scenarios:
Scenario 1: Roaming to AP2 and BTM query is sent to AP2.
1. Connected to AP1.
2. <Low RSSI> triggered roam to AP2. Successful roam to AP2.
==== Roam stats event 1 with full TLV case with AP1
(scan_type == partial, roam_trigger = low rssi) ====
3. BTM query to AP2 after 1sec.
4. BTM req from AP2
5. BTM resp to AP2
==== Roam stats event 2 with full TLV case having AP2 BTM info
(scan_type ==NO_SCAN, roam_trigger = BTM) ====
Scenario 2: Connected to AP1, send BTM query to AP1
==== Roam stats event 1 with full TLV case having AP1 BTM info
(scan_type ==NO_SCAN, roam_trigger = BTM) ====
Scenario 3: BTM request initiated by the AP
1. Connected to AP1.
2. AP1 sends BTM request with disassoc imminent set.
3. Roam scan is triggered.
4. BTM response to AP1
5. Roam to AP2.
==== Roam stats event 1 with full TLV case having AP1 BTM info
(scan_type = full or partial, roam_trigger = BTM) ====
6. Send BTM query to roamed AP2.
7. AP2 sends BTM req.
8. Send BTM resp to AP2
==== Roam stats event 2 with full TLV case having AP2 BTM info
(scan_type=NO_SCAN, roam_trigger = BTM) ====
Change-Id: I4571cbe75397fb795046abe8711571264ed98a65
CRs-Fixed: 3260060
In the api cm_roam_mgmt_frame_event(), TX status is sent
without conversion to the userspace resulting in
wrong value of tx status during logging.
Correct this by converting the tx status value before
sending to userspace in order for userspace to properly
evaluate the tx status.
Change-Id: Ie4b6b8bff5e8b9c88edfaf303ce6a4ae370edd67
CRs-Fixed: 3250473
To avoid unmeaningful roaming, when low RSSI trigger,
only roam when rx linkspeed is also bad.
Steps:
1. F/W indicates feature supported by:
wmi_service_linkspeed_roam_trigger_support
2. App sets vdev rx link speed threshold by vendor cmd.
3. Bus_bw_work gets rx link speed from data path periodically.
4. If found rx link speed change from good to poor, or poor to good, send
to F/W.
5. F/W low rssi roaming is triggered only when both RSSI and link speed are
poor.
Change-Id: I56829e42b26e407dd8e989a870aee2b3ea406232
CRs-Fixed: 3261996
WMI_ROAM_GET_VENDOR_CONTROL_PARAM_CMDID: Add support
for a new roam command to get vendor control parameters
from FW. Host needs to send proper param ID in command
(from enum WMI_ROAM_GET_VENDOR_CONTROL_PARAM_ID)
to get corresponding INI value from FW.
WMI_ROAM_GET_VENDOR_CONTROL_PARAM_EVENTID:
Add support for a new roam event to get param value
from FW. FW sends this event upon receiving
WMI_ROAM_GET_VENDOR_CONTROL_PARAM_CMDID command.
Change-Id: I03679bcf359a0f425aab7b9ea1c3cb6d84fbb0ca
CRs-Fixed: 3225160
Add new tags for reassociation request and reassociation
response. Parse the association id from roam stats event
and send it over the connectivity logging event
Add support to print AID and BT-COEX field.
Change-Id: I7926b5c69a84404b666acfd5e2db30426d085881
CRs-Fixed: 3221624
Add support to parse a new INI named
"bss_load_trigger_6g_rssi_threshold/RoamCU_6GRSSIRange"
and send its value to FW via WMI_ROAM_BSS_LOAD_CONFIG_CMDID.
Min, Max and default value of this INI:
Min: -120
Max: 0
Default: -70
Change-Id: I9aa99d887553de4022fc0a31dc0644601cd340d6
CRs-Fixed: 3225548
Currently host sends first, final bmiss count to fw
Add support for bmiss timeout(in seconds)
during wakeup as well as sleep state to fw.
Change-Id: Id748fabdff94f5fa3038bcea1b1cac733ac2dbe1
CRs-Fixed: 3224106
