One of the parameters to the ucfg_dp_config_direct_link() stub
implementation does not match the associated parameter in the
prototype. The stub and the prototype should match, so modify the
stub to align with the prototype, which matches the non-stub
implementation.
Change-Id: If9dda7db2bfbbce94c0356a73b33ae7569337955
CRs-Fixed: 3424788
If roaming is triggered by source CM_ROAMING_NUD_FAILURE,
then per the INI gEnableNUDTracking to check whether
disconnect current connection or not.
gEnableNUDTracking=2, keeping the connection
gEnableNUDTracking=3, disconnect the connection
Change-Id: I0f321dcf5f3fc1bf7d0c93fa0d70bf4770ccaf35
CRs-Fixed: 3412213
Previously, IPA had its default vote which will bump up the SNOC
frequency to 200 MHz. Now IPA has removed its vote which is
causing throughput drop in HE cases for SAP and P2P GO mode.
To fix this, add new throughput level TPUT_LEVEL_HIGH_HE_CASE and
provide ini to set its threshold to increase SNOC frequency to
200 MHz. To enable, set ini BandwidthMidHighThreshold to 7000.
Change-Id: Ica8c640597c37602aea2f5e4ff6b0646c49ff548
CRs-Fixed: 3297833
Create sysfs file for direct link unit test command to
generate traffic from LPASS.
Add ini to enable direct link unit testing.
Change-Id: I5b143bc6751eedb1a65cd836ea738744b72cc2cc
CRs-Fixed: 3365576
The kernel-doc script identified some documentation issues in
components/dp, so fix them.
Change-Id: Ic6297d80cda845287e7a472add244c489afd253b
CRs-Fixed: 3362039
When Vdev for direct link is up, set packets for this vdev to
route to firmware and only enter d0 WOW.
If the AP profile is HOST_CONCURRENT_AP_POLICY_GAMING_AUDIO,
prevent link to go to low power states to reduce latency.
Change-Id: I9fa2ab06983db8767d8b48b74e30602e07294fe2
CRs-Fixed: 3330207
Add ucfg APIs to set/get feature status and dscp
values and structure to store values
Change-Id: I839c89696581b8aefd873a120d938a5cbbc32899
CRs-Fixed: 3255692
To avoid unmeaningful roaming, when low RSSI trigger,
only roam when rx linkspeed is also bad.
Steps:
1. F/W indicates feature supported by:
wmi_service_linkspeed_roam_trigger_support
2. App sets vdev rx link speed threshold by vendor cmd.
3. Bus_bw_work gets rx link speed from data path periodically.
4. If found rx link speed change from good to poor, or poor to good, send
to F/W.
5. F/W low rssi roaming is triggered only when both RSSI and link speed are
poor.
Change-Id: I2c2a22c1f24a730783ee09455f4d70b099d9bff1
CRs-Fixed: 3255036
Currently there is compilation issue in case of IPA
offload enable case due to code changes done as
part of DP componentization.
Fix compilation issue by adding calls to DP component APIs
Change-Id: Id545f67bff75682ceccba5725f956a89c6b9b9f8
CRs-Fixed: 3259293
Currently while attaching vdev to DP interface
we are searching DP interface based on the Adapter
MAC address, but if STA MLD and Link address is
same, we were getting the Link Interface instead of
MLD interface, which was causing the EAPOL packet to drop.
To Fix the issue, instead of searching for DP interface
based on MAC address, use netdev to search DP interface.
Change-Id: I50c7974c053717b496fab0eeb89774af382b4313
CRs-Fixed: 3258684
Currently we are getting current vote level and bus bandwidth
high threshold from hdd context. But these are moved to dp
context under dp component.
So to fix issue add and call ucfg api to get and set values.
Change-Id: I2c36b2df76c5932dc0d1bdbdec21ce2da5f537bc
CRs-Fixed: 3252743
While requesting sta stats, tx/rx netdev stats update are
happening from adapter. But as part of latest code change
these stats are moved from adapter to dp interface, because
of which some of stats values are displayed as 0.
To Fix the issue get tx/rx netdev stats from dp interface,
Also add calls to clear netdev stats
Change-Id: I64523b035c1d902ccc4a45d82f7508751e518150
CRs-Fixed: 3247540
Currently, while we request netdev stats
we use the MAC address to find the DP interface.
There is a possibility that while we are
passing mac address to find DP interface
in parallel dynamic MAC update can happen
which will cause MAC address mismatch,
which will result in the DP interface not found
issue.
To fix the issue, instead of MAC address use
netdev name to search DP interface from
the list of available DP interface.
Change-Id: Ib04ce2fc7193be4733b16707600a10d3d729813c
CRs-Fixed: 3247725
Combined dp process mic error support for both SAP
and STA interfaces into one API for DP component
Change-Id: Ic78675d4bfdd5b5cc995505bcbf9862711c5ba24
CRs-Fixed: 3226471
Added new threshold corresponding to SUPER_HIGH
throughput and maxed out vote level to PLD_BUS_WIDTH_MAX.
Change-Id: I3d249fde7101d780bcfb6fba830ae2b255f02063
CRs-Fixed: 3194303
Implement per packet TX/RX support in DP componentization model.
This change will help to process per packet TX/RX path in STA interface.
Change-Id: I3fbd8dbe26ccd24fc50c6e67cd1213c72837cf9b
CRs-Fixed: 3173449
Add target_if API to send ARP request, LRO config and
DHCP indiacation to firmware.
Change-Id: I2d4af7a5da6c29398ab00205654df9be3d90b665
CRs-Fixed: 3165155
Implement DP component infra support, So that
DP component gets allocated and initialiazed.
Change-Id: Icdcbf92956dcf0984dd14262f3c7f29554b4eba8
CRs-Fixed: 3164965
