ol_defines header inclusion is invalid in WMI layer.
Remove the header inclusion by abstracting the dependency
with in WMI layer.
Change-Id: I5eb8624605cde20b516a1d8d0c823996c363e119
CRs-Fixed: 2023821
Add support in WMI layer to configure coex config command for
lithium based chipsets
CRs-Fixed: 2037499
Change-Id: Ib83407524bd3b5cdad28f73a6ccc36d4a0271779
Requirement is to get CCA from frmware when connection fails due to
assoc/auth/probe response timeout. These are common changes to get
CCA from firmware.
Change-Id: I062343ed065d7b0c38b9e3b24ecfa9851b9b1537
CRs-Fixed: 2031843
Host support for Static and Dynamic chain mask selection.
parse new TLVs from ext service ready,copy tables to
wlan_objmgr_soc object.
CRs-Fixed: 2016643.
Change-Id: Ia4735eb4c7774c381df01f56696e8c86fc6c56ab
Make the following TLV WMI layer changes related to 160/80+80 MHz
functionality:
- While forming the VDEV start/restart command, if the request from
the upper layer indicates the dfs_set_cfreq2 flag, then enable the
WMI_CHAN_FLAG_DFS_CFREQ2 channel flag. This is needed in order to
enable radar event reporting for the secondary 80 MHz segment.
Make this change only in the WIN specific implementation of
copy_channel_info(). If required for MCL, to be handled separately.
- Move the 'peer_bw_rxnss_override' member in
'struct peer_assoc_params' to outside the '#ifndef CONFIG_MCL'
section so that it is available both on MCL and WIN. Since
in MCL code peer_assoc_params is initialized to all zeros and
peer_bw_rxnss_override is not set anywhere later, this should
have no side effects.
- While forming the PEER assoc completion command, populate the
peer_bw_rxnss_override field as per the corresponding parameter
sent by the upper layer. This is required for providing override
values of Rx NSS for bandwidths higher than 80 MHz.
Testing:
- Tested on QCA8074 that the WMI_CHAN_FLAG_DFS_CFREQ2 channel flag
is being set in the VDEV start command if the secondary 80 MHz
lies on DFS channels (tried VHT160 and VHT80_80)
- Tested on QCA8074 AP and STA that the peer_bw_rxnss_override
value is being set in the PEER assoc completion command to
indicate Rx NSS value 2, when NSS value 4 is used for <=80 MHz
(tried VHT160 and VHT80_80). Also tested ping.
Change-Id: Ic45d80567eeed3707f76e513f772ce4da71d6ee0
CRs-Fixed: 2022037
WMI RX event processing is very critical for WLAN driver and today
we are using kernel's shared event work queue. Shared event work
queue is used by many drivers and if any work submitted in shared
work queue takes longer time to finish then it directly impacts WLAN
control path processing.
Define a dedicated work queue for WMI RX event processing and use
it for WMI RX event handling.
Change-Id: I8ee6ca5b4b20c3357d46f8b56943078a0a76977f
CRs-Fixed: 2029775
Create output agnostic log print APIs for WMI and Credit History to
enhance the debugging experience.
Change-Id: Ie89a9cb3b54c373ac2610d62003e940da17696d8
CRs-Fixed: 2028762
Converged FW has few left-over WIN specfic WMI CMDs that need to be
implemented in TLV method.
WMI CMDs implemented through this change -
WMI_PDEV_SET_QUIET_MODE_CMDID
WMI_PEER_MCAST_GROUP_CMDID
WMI_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID
WMI_VDEV_SPECTRAL_SCAN_ENABLE_CMDID
WMI_PEER_BWF_REQUEST_CMDID
WMI_PDEV_QVIT_CMDID
WMI_PDEV_SET_WMM_PARAMS_CMDID
Change-Id: Ia2ae3d2e56608fd4c51754ae2c78f2b9912d7172
CRs-Fixed: 1115239
Add new API to unregister event handler to allow
converged components to move to common eventid space.
Change-Id: I97f096ff3e36bc7923718498c535fb6c3c50e7e7
CRs-Fixed: 2023157
Due to different layers, TLV processing is confined to WMI folder.
Therefore, move the TLV layer processing of WMI_REG_CHAN_LIST_EVENTID
to the wmi folder.
Change-Id: I7e7182997a9506035030f33d2f81a403fbe97a2f
CR-Fixed: 2019750
Add changes for peer association by adding support to
include HE capabilities and HE operation information
in vdev start and peer assoc WMI commands.
Change-Id: I50c0241f872219e08ee2d231c907309ee5adceef
CRs-Fixed: 1073481
Defines API and callbacks of os interface for P2P component. At the
same time, defines API of target interface.
Change-Id: Ice1c86ecba1f2410d965d9f84923589f229a1864
CRs-Fixed: 2013763
Include cac duration and regulatory domain in vdev start
command, these fields are used to process phyerrors when
dfs is offloaded to firmware.
Change-Id: I5736354913fafb7776ac71e85dc23e841de94a96
CRs-Fixed: 2017481
Add support to pass delay_start_time to firmware, this delay will be
used before starting the first scan cycle.
Change-Id: I7488fc8da4e22b170e52fb38c8a1d5b49dbf7e2f
CRs-Fixed: 2014142
Remove WMI VDEV param population for HE ofdma_cplen
command. Instead use the same old short_gi command
for HE ofdma cplen.
Change-Id: Id303dab1c7ec47ebc31fc685ad0b50ddfdf4fcac
CRs-Fixed: 2009118
Curretly FW considers minimum time of hysteresis for PER based roam as
constant value which is 25 seconds.
Add changes to make this time configurable using ini.
Change-Id: Iadb5f6a005b069e0d6190df34e382927425ec1af
CRs-Fixed: 2005849
DUT should be able to roam to a better access point if current
AP is having congestion/packet error.
This roam also devise a new selection logic for candidate
selection which considers channel congestion and AP capabilities.
Change-Id: I6cffbf0de059a218e971be32fbdc1a0092ceea9d
CRs-Fixed: 1090934
Active Mode Berkeley Packet Filter (Active BPF) is a new feature that
allows firmware to apply BPF even while the Apps processor is active.
There are 3 modes:
* Disabled: do not apply BPF in active mode
* Enabled: apply BPF to all packets in active mode
* Adaptive: apply BPF up to some threshold to avoid performance impact
Add WMI APIs and related logic to support configuration of Active BPF
Mode.
Change-Id: I8c0778b3fa73d148422aa103b0fc0950433fec95
CRs-Fixed: 1111400
Converged FW has few left-over WIN specfic WMI CMDs that need to be
implemented in TLV method.
WMI CMDs implemented through this change -
WMI_GPIO_CONFIG_CMDID
WMI_GPIO_OUTPUT_CMDID
WMI_PDEV_DFS_DISABLE_CMDID
WMI_PDEV_DFS_ENABLE_CMDID
WMI_PDEV_GET_NFCAL_POWER_CMDID
WMI_PDEV_SET_HT_CAP_IE_CMDID
WMI_PDEV_SET_VHT_CAP_IE_CMDID
Change-Id: Iad5532b305fae12f4eb8265cf9a662578041d06e
CRs-Fixed: 1115239
Converged FW has few left-over WIN specfic WMI CMDs that need to be
implemented in TLV method.
WMI CMDs implemented through this change -
WMI_PDEV_SET_ANTENNA_SWITCH_TABLE_CMDID
WMI_PEER_SMART_ANT_SET_TRAIN_INFO_CMDID
WMI_PEER_SMART_ANT_SET_NODE_CONFIG_OPS_CMDID
WMI_PEER_ATF_REQUEST_CMDID
WMI_FWTEST_CMDID
WMI_QBOOST_CFG_CMDID
Change-Id: Ice617f7adf387d534edaefd24857c253c937de48
CRs-Fixed: 1115239
Converged FW has few left-over WIN specfic WMI CMDs that need to be
implemented in TLV method.
WMI CMDs implemented through this change -
WMI_PDEV_SMART_ANT_ENABLE_CMDID
WMI_PDEV_SMART_ANT_SET_RX_ANTENNA_CMDID
WMI_PDEV_SET_CTL_TABLE_CMDID
WMI_PDEV_SET_MIMOGAIN_TABLE_CMDID
WMI_PDEV_GET_TPC_CMDID
WMI_VDEV_RATEMASK_CMDID
WMI_VDEV_SET_DSCP_TID_MAP_CMDID
WMI_VDEV_FILTER_NEIGHBOR_RX_PACKETS_CMDID
WMI_PEER_UPDATE_WDS_ENTRY_CMDID
WMI_PEER_SMART_ANT_SET_TX_ANTENNA_CMDID
Change-Id: I6e59bcb948a7368729df35d19c3d5a03a0075a15
CRs-Fixed: 1115239
Object manager psoc service ready api provides host (ext)service ready
data structures hence remove duplicate copy from wmi_unified_param.h
and change WMI to use psoc service ready data structures.
Change-Id: Iaec20e9b818077ed1ca58754c4b1bc6deaedd761
CRs-Fixed: 2002016
Currently, Host maintain multiple data structure at different
layers for offload related features like arp/ns/gtk etc.
Instead of using many structure use single data structure across
all layers for offload related feature (arp/ns/gtk) which is now
exposed by PMO. Hence to include PMO header's in WMI, refactor the
WMI code for PMO component by carving out PMO specific functionality
separatley.
Change-Id: I8314d5ece49bf6972fbe706d635385ae22d11b2e
CRs-Fixed: 2004523
Added host WMI VDEV param enumerations for new HE
commands Populated VDEV param TLV with WMI VDEV
commands ids for all the new HE commands.
Change-Id: Id9905176c7565dfa0dd56800b61b7c620136a4e7
CRs-Fixed: 2009118
Add HE Mac, PHY , MCS , OP & PPET in peer_assoc_params
structure. Add HE PHY & PPET in wmi_host_mac_phy_caps
structure. Populate HE params while sending WMI Peer
assoc commands.Parse HE Phy & PPET while parsing Mac
Phy TLV in Service ready extension event.Add required
changes in psoc_service_ready header files.
Change-Id: Ia2fc7f54634a7a0c98996e361e38b11b3b74a7a0
CRs-Fixed: 2009118
Add multiple vdev restart command request WMI command API and
extraction API for CSA count status event to support CSA implementation
for beacon offload.
Change-Id: Ic309f592137dc725e04590dc0093f30b481ebf9b
CRs-Fixed: 2000449
Added support for wmi_pdev_param_mesh_mcast_enable and
WMI_SERVICE_ENTERPRISE_MESH
Change-Id: Ie0ce2b822843d66aa14fe0a46809a78e9143f5d9
CRs-Fixed: 2003389
wmi_host_mgmt_rx_hdr struct cleanup for UMAC covergence as
struct mgmt_rx_event_params is to be used in place of
wmi_host_mgmt_rx_hdr.
Change-Id: I7ad3b641e492ecb469fa69c0025c6537c8a01e65
CRs-Fixed: 1103247
Send beacon frame in wmi_roam_invoke_cmd to firmware
This helps firmware skip scan to connect to requested
BSSID.
Change-Id: I5c6e375309dcb3bdd6430a3d501bade5cfe2e88d
CRs-Fixed: 1116901
Firmware requires WMI commands to be sent on different copy engine for
each MAC. Add support in WMI to use different endpoints for each pdev.
Change-Id: Ie0dfe71043275ac694362f88b625219f089b5303
CRs-Fixed: 2005214
Support to add hw_mode in init command is added by FW
to let host choose the mode to be use. Change init cmd
send API to enable upper layer to send the hw_mode selected.
Since this is new TLV in init command, init cmd send API
needs to be changed to accommodate this parameter.
Change-Id: I172d8d737425599c36666d9fec8a6cdd48085097
CRs-Fixed: 2004652
pdev_id is required to identify the pdev object on which this event is
recieved. Add pdev_id in the event extract API.
Change-Id: Ia910d42af6a9d6099da1b7781601b0320dff80ba
CRs-Fixed: 2003898
pdev_id is used to get the pdev for which the event is recieved. Add this
in extract APIs to fetch the pdev from pdev_ids and use it for further
processing. This is change is part of changes required to support
multi-radio.
Change-Id: Iadda098ccb31be5e8e43083158802abe49ac01b4
CRs-Fixed: 2003898
Converge on common WMI event handling for (ext)service ready
such that common PSOC object can be populated after common parsing.
Legacy (ext)service ready handlers continue to co-exist to support
legacy modules. Legacy service ready handlers can be removed once
legacy modules are also componentized and start using new object
model of PSOC, PDEV, VDEV and PEER.
To support multiple SoCs register for various psoc objects via legacy
callback registration routine during psoc probe and populate common
psoc object once WMI (ext)service ready event is parsed.
CRs-Fixed: 1110768
Change-Id: I966b8f7c775a19ac6e51ad5217a2dd0287acfada
