Add change to print file type which is getting
downloaded from cnss2 platform driver to wlan fw.
Change-Id: I737c9c04bc02a3cd320362f230a0862321ec312c
CRs-Fixed: 3401928
Should power off HST/HSP if it only finished pcie
enumeration without WLAN driver load before do
LPM. Otherwise, it will cause the mhi state switch
from INIT to SUSPEND failure that block LPM.
Change-Id: Ia2c5fbf0a2bf9c088be548eb533d7836f45a3cfd
CRs-Fixed: 3283893
cnss driver is supposed to be supported across platforms regardless of
CONFIG_PCI_MSM. Hence using CONFIG_PCI_MSM to decide if cnss2 needs to
be compiled is not correct.
This reverts Change-Id: I9ab82aeca945d29d3608e65ecbe69902f8a5b47b.
Change-Id: I1ab90e80694b0e45270f6b47666781d784f8ab76
CRs-Fixed: 3405347
User may configure such runtime_pm debugfs unexpected during test,
add the log to explicitly show what is configured.
Change-Id: I7d427603bfc7e6bb5d732fa3e29ff66c965e153b
CRs-Fixed: 3399930
Current implementation tries to collect FW dump when cnss shutdown,
and then ASSERT after collection complete.
Do not invoke CNSS_ASSERT if SSR enabled.
Change-Id: I8d427603bfc7e6bb5d732fa3e29ff66c965e153b
CRs-Fixed: 3399930
Add cnss2 code changes to register with thermal framework to support
thermal mitigation.
Change-Id: I9d427603bfc7e6bb5d732fa3e29ff66c965e153b
CRs-Fixed: 3386762
As per Hibernate Entry (i.e. SUBSYS_BEFORE_SHUTDOWN with flag
crashed is not set) and based on low power supports it set the
state to ICNSS_LOW_POWER.
While processing the SUBSYS_AFTER_SHUTDOWN, its reset the
ICNSS_LOW_POWER state based on previous state already set
state and low power supported.
But before system freeze callback triggered,
SUBSYS_AFTER_SHUTDOWN event received to wlan and due to
which ICNSS_LOW_POWER state is clear and freeze callback failed,
thus its leads to prevent Hibernate freeze on WLAN.
This fix is to provides WLAN entered into Hibernate freeze state
by not clearing ICNSS_LOW_POWER state in SUBSYS_AFTER_SHUTDOWN.
Change-Id: I7b34d54c7ce5314e5092dbe2c0bc65ffe13d014d
CRs-Fixed: 3394501
Hibernate is a system wide power mode during which Modem
would be brought down along with DDR and the RAM contents
would be saved on the disk (suspend-to-Disk).
Modem would be do graceful shutdown in Hibernate mode,
so BEFORE_SUBSYS_DOWN notification will be received.
Based on dtsi node "is_low_power", if BEFORE_SUBSYS_DOWN
with notif->crashed bit not set is received, platform
driver will trigger an idle shutdown and set low power mode.
On AFTER_SUBSYS_DOWN notification, low power mode will be
cleared if it was set and ramdump collection will happen
only in case of crash.
Change-Id: I7b618e7c23950e4055079cde237ed75d6861620f
CRs-Fixed: 3394501
Deep Sleep is a system wide low power mode during which
Modem would be brought down and DDR would be in self
refresh mode (suspend-to-RAM) thus platform driver on
receiving deep sleep indication goes to a state similar
to SSR apart from the fact that FW is not crashed but
deliberately brought down.
In msm-5.15, there are no seperate notifications used
for deep sleep, notifications used for hibernate like
BEFORE_SHUTDOWN, AFTER_SHUTDOWN, BEFORE_POWERUP and
AFTER_POWERUP are used for deep sleep also.
In this commit add only low power mode state to
icnss driver state.
Change-Id: I4b12c5a8841e3cfc3e5e44ab6d9dff141e472876
CRs-Fixed: 3394501
Icnss driver receives early crash indication when
fatal error happens in wpss. In few cases rproc
framework didn't receive any notification regarding
wpss fatal crash due to which icnss driver wpss
notfier is not getting called. This prevents wpss ssr
recovery. To recover wpss from this scenerio icnss
driver tries to do self recovery of wpss subystem.
Change-Id: Ie22dfb6a6218aafd1fec84fb14f3efb16c60bf5e
CRs-Fixed: 3265930
Recovery timer is used to detect FW_READY timeout(60 Sec)
during SSR/PDR recovery and assert. Same timer starts
before cold boot calibration also and expires in 40 sec
if FW_READY is not received.
Change-Id: Ie4e2a327aa4f4df49b8684f9c178b9b5f4d4fb15
CRs-Fixed: 3221566
This change shutdown wpss on device shutdown for
adrastea targets. With this change icnss driver unloads
wlan host driver in wpss shutdown callback.
Change-Id: I6d7d2563e694786b8d74725d77dc8c25943198e9
CRs-Fixed: 3392307
Currently, the cnss2 platform driver just can support
one wlan device attached, so do the following changes
to cover dual wlan card attach case. Firstly, delay
the second device go to pcie link suspend and power
off state to make sure it really finished the pcie
enumeration. Then pcie enumeration succeeds with
multi-devices. Secondly, supporting to write the qrtr
node instance id to PCIE register for wlan fw reading,
which can fix qmi message exchange failure if active
two Hastings devices. Thirdly, change the usage of
plat_env to support dual Hastings.
Change-Id: Ica41a23d4e983b91c0ff1b4e76b380803fb877ab
slatecom_interface.h file is moved to include/ in kernel,
update the same in icnss2 also.
Change-Id: Ibd07235636066b48221de9928283bfdf24b90221
CRs-Fixed: 3390989
Connection-roaming INI file and its backup files are optional.
So if these files are not present on a device, then do not log error
indicating files are not found.
Change-Id: I1a8fdaf6db75fff0e867c5454d16c40b72d6fbdb
CRs-Fixed: 3389578
Add support for AUX UC capability and PCIe link control QMI messages
by updating the WLAN Firmware Service QMI file with the latest IDL file.
Change-Id: I3c51bbad8def33a727210ec80cad799fbb72b895
CRs-Fixed: 3385851
Currently CNSS2 is getting compiled by default and it depends
on MHI & PCIE driver code and in Atherton_target MHI & PCIE
code is not enabled.
To avoid CNSS2 driver compilation, add CONFIG_PCI_MSM check
in Makefile.
Change-Id: I9ab82aeca945d29d3608e65ecbe69902f8a5b47b
CRs-Fixed: 3356064
Call collect_driver_dump() driver ops to add the data from the buffer
for the four log types.
Change-Id: Ic06d4520de6f87202d1c3ce24362d61002b85f61
CRs-Fixed: 3352310
When server arrive event is received send wlan boot init command
and when firmware ready indication is received send
wlan boot complete to co-processor subsystem.
Change-Id: I1c75ca772b7b96757f1b060b6c1d5700245b17aa
WLAN RFA is present on another co-processor subsystem.
Any error fatal in co-processor subsystem will result in
WLAN reset.
In order to make sure that rf clock/rails are up
before accessing WLAN hardware, ICNSS platform driver
needs to register with co-processor SSR notification and trigger
PDR once co-processor is down.
Change-Id: I28cdc997646cc15ef0de23c28dfada87972eb465
WLAN RFA is present in another co-processor subsystem.
In order to prevent unclocked access, Wait for SLATE_POWER_UP
event before starting wlan cold boot qmi handshakes.
Change-Id: If24816c270c32c5f0191227ef66bc4a31549c54d
WLAN RFA is present on another co-processor subsystem.
Any error fatal in co-processor subsystem will result in
WLAN reset.
In order to make sure that rf clock/rails are up before
accessing WLAN hardware, ICNSS platform driver needs to
register with co-processor SSR notification and wait for
POWER_UP event before starting QMI handshake.
Change-Id: Idf65e508a09d93e481349afc73de4804c7841111
Keep PCSS recovery config as persistent during the whole
lifetime of cnss driver, and send it to WLAN firmware
service upon receiving firmware ready event.
Change-Id: Iec6c35c82750df3f8fd43723d102bcabfb539874
CRs-Fixed: 3378798
WLAN IOMMU mappings have cached attribute set whereas
ADSP IOMMU mappings do not have cached attribute set.
This is resulting in an inconsistent memory view between
ADSP SS and WLAN SS. ADSP writes to a DDR location and
WLAN HW reads from the same location but since access is
cached from WLAN side, there is a possibility of reading
incorrect values.
Fix is to use IOMMU_CACHE flag for audio smmu mappings.
Change-Id: Ife97bee34bc8224fd2d0d2bb45b606efeea5aa53
CRs-Fixed: 3375521
If device tree doesn't configure any regulators for
device, means this device doesn't need extra regulator.
This case shall not be treated as an error.
Return a positive value for this case to allow caller to
make proper choice.
Change-Id: I7ead81b3915d16f966f94c9d916e0d67bc04fda0
CRs-Fixed: 3355141
Send rf_subtype based on dt node "qcom, rf_subtype" to
firmware using QMI_WLFW_WLAN_HW_INIT_CFG message after
qmi server arrive. Firmware will initialize different
halphy code based on rf_subtype sent by host.
Currently, this change will be applicable only for
adreastea targets which can have either slate RF or Apache
RF attached.
Change-Id: Iba327d0c221104a4ebb55a72d42e1a4b8dcb66c3
Add a data length validation check in fw response message in
qdss_data_send_sync().
Change-Id: I750f46549bc914698baaf4e24f1710536ca8e356
CRs-Fixed: 3366343
Some auto HW can't guarantee wlan_en low state when powerup.
Add a macro to enable initializing wlan_en state.
Change-Id: I6755bcd49c78f7bb9931f80cb385e62177ebe603
CRs-Fixed: 3355148
Added below mentioned changes to support qca6174 in cnss2 driver.
1. While resuming pci link, restore the pci config space before
enabling pci device.
2. Add 10ms delay between wlan_en become active and pcie reset
de-assert.
3. For wlan chipsets which don't support cold boot calibration,
schedule Wlan driver load in cnss_cold_boot_cal_start_hdlr.
Change-Id: I28435896314783353db5dd830051df9467be6585
CRs-Fixed: 3359223
Icnss and cnss2 driver receives and sends memory size
over qmi to and from wlan fw. This change add maximum
memory size check before sending or receiving fw mem size
over qmi. Also, use QMI_WLFW_MAX_NUM_MEM_SEG_V01 enum as
maximum size limit.
Change-Id: I392bfbbf0359e60bce9e93d909a119e8c72f07d5
CRs-Fixed: 3367408
Add NULL check for 'dev' pointer before passing to
cnss_bus_dev_to_plat_priv function.
Change-Id: I8ab93a71219638e4b66d3b9fdcb164e052385129
CRs-Fixed: 3364740
Add NULL check for 'dev' pointer before passing to
cnss_bus_dev_to_plat_priv function.
Change-Id: I319a9859c41d7e8096b3a4457f4a831e0e93f7ab
CRs-Fixed: 3360223
For WIN use case maximum number of memory segments requested
by FW is increased to 52 in QMI layer. Since CNSS2 driver uses
same QMI header files and message structures the same maximum
number of segment is applicable for CNSS2. It means for memory
allocation, FW can request 52 memory segments to CNSS2 via QMI
indication but local CNSS2 variable which get segment info from
indication supports maximum 32 segments.
To fix it, change CNSS2 array variable size to same as number of
maximum segment supported in QMI layer.
Change-Id: I661b55b53cb31327da12f064d0a516884159eb5b
CRs-Fixed: 3355665
Add a data length validation check in fw response message in
qdss_data_send_sync().
Change-Id: I197b8d52c06e35f5fcf0f8fee94429fdcf500fcb
CRs-Fixed: 3359589
When strict-prototypes and format-insufficient-args are
enabled then icnss2 fails to build. Change prototype of
icnss_get_plat_priv() and remove extra arg from error log
in icnss_wlfw_wlan_mac_req_send_sync().
Change-Id: I81c7d90fa24b05d573a9ce47c0301d2798118182
CRs-Fixed: 3359853
Add support for IOMMU map and unmap of WLAN memory
regions into Audio SMMU for direct link usecases.
Change-Id: Ic136b1e5ac22641b6612ab5285452273233fcaea
smcinvoke.h header file is moved to include/linux for pineapple target.
Hence, include smcinvoke.h from include/linux path.
Change-Id: Iec5622b09f8dd6536f5b9c8f81c46320731ba630
CRs-Fixed: 3354727
