Add function to parse pll_codes from dfps_data_region, and the
pll_codes are used as trim_codes for RFI.
Change-Id: Ic81529cd685f17012809fb68cefc4b36cb1172ca
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Primary and secondary dsi displays are built-in displays
and they are supported during all concurrency usecases
without resource allocation failure. DP mode filter
logic should provide supported mode information based
on free mdp resources after dsi resource assignment.
Change-Id: I3a9637a91ea1ffcc31997e25caff7f13605283ac
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Lots of dsi FIFO error logs were printed into serial in
dsi ISR. It will make device stuck or deadlock. Remove
these logs from dsi ISR, and enable the log in FIFO error
workqueue handler.
Change-Id: I0e9b2312cb76d345ec5a9b9628c52b47d5163fde
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
This is a common case that seamless transition was rejected
when active/connectors changed, so just print an info log here.
Change-Id: Iada9ad84af1c072ccdbc97f5bf438de6a032f45f
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
Use lower frame threshold time for high refresh rates. For resfreh rates
greater than 120 FPS the threshold time is 500us.
Change-Id: Ie5a37c0eec6c2c2cbf90e039eb6b15bc7edd2492
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add function to parse pll_codes from dfps_data_region, and the
pll_codes are used as trim_codes for RFI.
Change-Id: I5b16be94a9e47dff515dea036839f74c2ddd8824
Signed-off-by: Bruce Hoo <bingchua@codeaurora.org>
Since some property of panel dtsi were not a must.
Do not report errors for panel bindings that are
not mandatory.
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
Change-Id: Ie899081e2ca93740ceb854457b61e5fc5d2083fa
Panels supporting Cphy use a specific divider
blocks. Add additional divider blocks for byte
and pixel clock output to support DSI CPHY.
Change-Id: I74b3ee2bdd22ae8fa20567fe837e03915537c4fb
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
If the command line timing is given, select corresponding
drm display mode as preferred mode. Select first sub mode of
that timing as preferred mode if dynamic clock or dynamic fps
is enabled.
Change-Id: I688b3bc07f79f4d014b8a7797204d3d6a873222d
Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org>
Add support to read cphy boolean flag from panel dtsi
and configure DSI PHY registers accordingly. Update the
bit/byte clock calculation according to cphy specifications.
Update clock parents so that the relevant divider blocks
are configured to support cphy.
Change-Id: Iaca61eec01a488657b086f59910c52f8c79e26a4
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
In order to make dsi panel and dsi2hdmi panel compatible,
delete "qcom,panel-force-clock-lane-hs" property in phy and
use display panel's force_clk_lane_hs property.
Change-Id: I490e08b2ee859797c2b3aeddf109a3a4286fb922
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add DSI api to control the connection status of the
DSI interface. This would be used in the VM usecase,
where the connection would be enabled/disabled during
device assign/unassign while switching to the VM.
Change-Id: Ifff41244824ade7a6b8dca77651d82fd5207f8e0
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
In general the brightness value, the first parameter is low byte and
the second is high byte, but some DDIC invert, so add inverted display
brightness value property.
Change-Id: I8bf5631bb66096bd28529c53643e358afffce18e
Signed-off-by: Wenjun Zhang <wjzhan@codeaurora.org>
Change removes scaling for porches while calculating h_total, as
it is not necessary. Using scaling for porches results in lower
clocks which in turn can lead to low FPS.
Change-Id: Idbad83e1c56f079e60fe5ac342f8dd977db54f8f
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change updates resource topology mapping tables and includes
logic to compare compression types for dsc vs vdc.
Change-Id: I1735edeb07aec8ed0065f84ac0824c58158412f3
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
This change sets the regulator voltage to zero for all
those regulators which support voltage scaling before
disabling the regulator. Failing to do so causes the regulator
vote to set to the last min value specified in the previous
set voltage call.
Additionally modified the config regulator api and renamed to
get regulator because of the above change.
Change-Id: Ie4c4842db0c08a4d98926ed79503cf84e4d5762a
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
Make msm_drm into single module and all child driver
registers and unregisters are handled from parent's
register and unregister respectively.
Change-Id: I017513d1de3b6b25dd5543d7fa7741c0bac1740d
Signed-off-by: Shashank Babu Chinta Venkata <sbchin@codeaurora.org>
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Add vote for panel regulators in dsi probe to make sure
panel regulators are ON until dsi bind is completed
for cont-splash enabled usecase. Remove this panel regulator
vote when dsi component bind is done.
Change-Id: I0b1d43fa1b16385712abc1d8aaa0e778f31ba634
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Update the VDC-m hardware version in the display driver as per
the latest programming guidelines.
Change-Id: I0073cb7b713599de43f2a675202390df3b4a1d58
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
VFP or HFP is adjusted to achieve constant fps during dynamic
DSI clock switch. This feature is not supported for command
mode. So, add check to skip porch calculation for command mode.
Change-Id: I5fa76d6536a55b2a19f24c0e14b6861e1f4c8f25
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change updates the parsing of timing nodes to check
the mode of operation as video or command. In command mode,
for each timing node, num of supported dfps rate is always
one. Accordingly, update the num_dfps_rate to 1 for
command mode.
Change-Id: I5098c7e0d4d2320609d6e10031eaef78c1d8b3c1
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Panel's physical width/height larger than 255mm is getting
truncated due to type conversion into smaller type.
Change-Id: I826fb2db542146c07d8379951563430b7da8288c
Signed-off-by: Rajeev Nandan <rajeevny@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Add support to allow creation of debugfs node only if
CONFIG_DEBUG_FS is enabled.
Change-Id: I1ae2c4188a99e3ed88f59fc021efc01407bf942d
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
There are some scenarios where a dfps request
during cwb session will result in cwb
encoder not getting disabled once the cwb
session is over. Add support to fail the
commit if any VRR or dynamic clock change
request is received during CWB transitions
to handle this.
Change-Id: Id3f192f79eac4ad0d7301bd34f7151fec243d685
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
DSI interrupt may be destroyed before it is disabled, it will cause to
the interrupt count can't be cleared, so subtrace DSI interrupt count
in disable function even it was destroyed.
Change-Id: I430b0281957db588c7405d5775d0c10f2f498b36
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Optimize pre mode switch panel command by transferring async. This
removes the time waited until subsequent dma_done irq.
Change-Id: I2e2516fdd641e85d1f1b221a6ea7999c868edf00
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change fixes the usecase where dsi msg flags validated only
during command transfer. This fix maintains the flags between
transfer and trigger calls. It also adds a new async override
flag to be used to bypass validate function.
Change-Id: Ie12acd3d7b01099bba65ca37cec61091408b81c5
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
While running the panel in simulation mode using sim-swte, ESD check is
invalid. The change doesn't set the ESD capabilities if watchdog timer
is being used for TE.
Change-Id: I375f369ad4602f21da6151e526e7b6e78fcea524
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
From Lahaina onwards, for compressed DSI output, widebus should be enabled.
In widebus mode, 6 bytes of data are transmitted per pclk.
For uncompressed output, widebus must be disabled to transmit 3 bytes
of uncompressed data per pclk.
Change-Id: I7fc0bdb2e1678152d57b4cbb8295063a2ba8ae73
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Move DSI debugbus dumping logic from DSI driver to sde_dbg
in order to utilize the framework in place for debugbuses.
This allows for more control over the dumping logic, such
as where the dump data is stored(memory/console), via nodes
populated in debugfs.
Change-Id: Iff507fdaa02d26af26743e81f6048aec57c09a76
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
If DPU hardware supports demura feature, install the connector
properties related to demura feature.
Change-Id: Ieaddfc695e9f57e3c45e2bc0bd2c2e103f895ba8
Signed-off-by: Gopikrishnaiah Anandan <agopik@codeaurora.org>
