Ensure the grp_id is not greater than MAX_TA_RA_ENTRIES to avoid
potential out of array illegal memory access.
Change-Id: I343fffe6078b33d0ec618ea7b4abbfd17c4bb814
CRs-Fixed: 3340482
Host stops cfr without vdev id check. In MLO case, the other link
stops firstly and it will get mac id base on wrong vdev id. Finallly,
it cause FW assert. This change adds vdev id check when getting cfr
rcc enabled params and trying to stop cfr.
Change-Id: I745ff5398b3f00fdb84b62b0835c1dd2ab75fae1
CRs-Fixed: 3296067
Changes to derive AoA phase values in RCC mode.
Add AoA phase calibration parameters to pdev_cfr. These
gets filled upon FW WMI event for every channel change.
HW reported AGC gain & these values are used to derive per
chain phase values.
FW to advertise support of this via service flag.
Change-Id: Ie239b939e50c60c5658ed0a82bae3243e5028e77
There is potential risk when starting CFR and resume happens at same
time, so this change adds wake lock for enhanced CFR.
Change-Id: Ifbde12cb73092b7fc4ef517e57051af4ffe7a79f
CRs-Fixed: 2974733
Host add support to send cfr data via nl events to userspace
applications. Host registers callback when user send vendor
command to set transport mode.
Change-Id: Ieed3b6e09d871639af58336074313120d51762e2
CRs-Fixed: 2952096
Separate the common fields of csi_cfr_header and update
the logic of calculating the cfr_metadata_len.
Move cmn header update code to single place.
CRs-Fixed: 2916901
Change-Id: I97d99df45f667f4ed3b80264b12d3d09a3bcae95
Allow cfr period to be multiples of 1ms for targets like
qcn9000, qca6018, qca8074v2 and qca5018.
For other targets, restrict it to be multiples of 10ms.
CRs-Fixed: 2878062
Change-Id: I7f5638adf8ef39f7b8b681ae6693f5f032217e88
Change the minimum CFR periodicity from 0 / 10ms to 0 / 2ms,
and ensure that the period value is multiples of 2ms.
Change-Id: I9112e47d21cbb40c83852e404bac3ce1b48897a4
CRs-Fixed: 2862591
The logging macros implicitly takes care of embedding function name
in the log, hence there is no need to include __func__ again.
Getting rid of redundant __func__ reduces driver memory footprint.
Change-Id: Ife4d1dbb9bfafa4381f1017e331ddef247c649c2
CRs-Fixed: 2774457
For kernel and driver logs, replace %pM and QDF_MAC_ADDR_STR/ARRAY
with QDF_MAC_ADDR_FMT.
For tx/rx mask, use QDF_FULL_MAC_FMT.
CRs-Fixed: 2763028
Change-Id: I6c56c2040967b279dd31100c4f376f2452146742
Repetitive channel capture configurations usually support
16 groups to be confugured. To check if a particular group
is enabled by user, qdf_test_bit is being used here.
qdf_test_bit usually operates with uint32_t and it takes
the argument as unsigned long type. Since,
modified_in_curr_session is declared as uint16_t, and then
typecasted into unsigned long.
Change the data type of modified_in_curr_session
from uint16_t to 'unsigned long' to avoid compiler
issues.
Change-Id: Iec778dc36d5671f2cfb643c9ced1bd2a6104de2b
CRs-Fixed: 2753267
Support a new capture_interval_mode: capture_count, where after
capture_count+1 number of frames, MAC stops channel capture and
waits for capture_interval duration before enabling again.
Add nob(capture_intervalmode_sel) to switch to capture_count or
capture_duration mode in wlanconfig application, where
capture_intervalmode_sel=0 indicates the old capture_durarion
mode where MAC stops channel capture after capture_duration
instead of capture_count. capture_intervalmode_sel=1 indicates
the capture_count mode.
Support MO marking: Current ENH CFR uses the existing MD/MO,
type/subtype filters to filterin the packets with programmed
type/subtype as either MD/MO. But for m_TARA it is also required
to consider the bw/nss/ta/ra setting. Therefore, it is possible
that not all the filtered-in PPDUs have channel capture and lead
to processing of packets which does not have captured data.
To overcome this issue, from QCN9000 onwards, MAC has MO marking
feature added for M_TARA filter mode, where MAC will consider
all TARA group configuration as filterin criteria & provides
an option to HOST to choose either filterin mode as FP or MO.
en_ta_ra_filter_in_as_fp is added to support MO marking.
Based on the discussion between HOST, FW & MAC teams, 0 is the
recommended & default setting for en_ta_ra_filter_in_as_fp.
Add nob to configure en_ta_ra_filter_in_as_fp but do not expose
to user.
Change-Id: I75cd3218fa4308afad21052e4535ef9b8e5a5869
When a one-shot capture is triggered with CFR, the state is not
reset to DISABLED after capture has completed. This affects HW mode
switch behavior because if CFR capture is ongoing (ENABLED), mode
switch is not allowed. This change checks for period to return DISABLED
or ENABLED. Period is 0 in case of one-shot capture.
Change-Id: Iae8727959a1becd3b5f4da166e868c1592910b84
CRs-Fixed: 2735166
For adrastea targets, enhanced CFR is not supported. When only
CONFIG_WLAN_CFR_ENABLE is set, some compilation errors are
observed as CONFIG_WLAN_ENH_CFR_ENABLE is not set true.
Fix these compilation errors when only CONFIG_WLAN_CFR_ENABLE
is set for targets which do not support enhanced CFR.
Change-Id: I96a769d8f10144033e48e123bb68d48a54cdf8ab
CRs-Fixed: 2706904
This API is used to parse the cfr capture metadata received in HTT msg
HTT_T2H_MSG_TYPE_CFR_DUMP_COMPL_IND from firmware. It reads the cfr dumps
from host allocated mem chunks for CFR using offset index received in
HTT msg, populates the CFR dumps into streamfs and updates the read
index of memory chunks allocated for CFR during init.
Change-Id: I2f49e308c3659779b8da7ae1baaceb5bfa968b4e
CRs-Fixed: 2687062
Retrieve the INI option to disable CFR and store the
same in pdev feature ext caps.
When CFR feature is disabled -
1. Skip pdev/peer cfr object allocations
2. Skip CFR SRNG allocations
3. Skip WMI registration for DBR and TX completion events
Change-Id: I5a7a6ae67d2c3a863b952e00e317c44a71e9fbc1
CRs-Fixed: 2671620
Add a interface to write string of CFR stopping, and indicate to
userspace that CFR has stopped.
Change-Id: Ib1d63cb75cd311b367d5d8100c5c4eb92980392d
CRs-Fixed: 2659373
FW requires to receive WMI_CFR_CAPTURE_FILTER_CMDID with the pdev id
which is based on the working band. It requires srng id when looking
up or releasing DMA address. So add this change to check working band
and set mac id. This is MCL only change.
Change-Id: I763a25b4989607128b2b4c75186eb5bdcd204077
CRs-Fixed: 2641268
1. Remove absolute paths to cfr header file.
2. Exclusion of CFR header file is handled in Kbuild,
remove compile flag within file.
Change-Id: I6abdce56716ba17481ccc2e1942754203063e3ad
CRs-Fixed: 2649714
FW may limit the interval and duration during which HW may
use user provided values and attempt to capture.
These values range from 1 us to roughly 16.8 sec.
Max value is 0xFFFFFF which is 16.777215 sec.
Add check to make sure that capture duration cannot exceed
capture interval.
Change-Id: I7aff00a1024d6d8ba9885cda3e1c36dd08c95f9e
CRs-Fixed: 2649714
This is part of moving CFR component to hostcmn. Fix compilation
issues in this change.
Change-Id: Ia0a40da1e7e9201ffc5d1700cccea4181b358842
CRs-Fixed: 2637129
