Add kernel timestamp attribute in enum qca_wlan_vendor_attr_diag
for subcmd QCA_NL80211_VENDOR_SUBCMD_DIAG_DATA to send it from
driver to userspace. Also, QCA_WLAN_VENDOR_ATTR_DIAG_HOST_TIMESTAMP
attribute indicates the system timestamp but is documented as kernel
timestamp wrongly. So correct the documentation of this attribute to
reflect the correct behavior.
Change-Id: I9559345185cb75ae6adc6792126fc6679b089e5d
CRs-Fixed: 3150783
Add QCA_WLAN_TWT_NOTIFY command type to send event to userspace when AP
changes TWT required bit field in its capabilities.
Change-Id: I6333213f4e8ca4fe9ca637db287759fd6c6622f4
CRs-Fixed: 3143525
Add support to receive the fft_recapture arg value
from spectraltool, handle the FFT recapture config and
pass this to FW. The recapture feature must be
enabled only for spectral scan period > 52 us and
Normal Spectral scans.
Change-Id: Ied637704d25bb15bff2139a215da7481d4f80e4f
CRs-Fixed: 3140890
Currently driver is doing unlink BSS when there is a connect failure.
This will cause an issue, for 2G+5G ML connection.
1) Connect on 5G link failed due to Auth failure
2) Connect on next candidate (2G) is success and FW is in SMM
3) Partner link(5G) connect will fail due to 5G scan entry won't
be found in SMM mode.
To avoid this, don't unlink the BSS for ML VDEV connect failure.
Change-Id: Icaa8c736d9038c971b5c3d459fd4af5a833bdc80
CRs-Fixed: 3129726
Add a new wrapper wlan_cfg80211_register_netdevice() that calls
cfg80211_register_netdevice for Kernel 5.12+.
Change-Id: I17655f1e3123d663d25b9dfc82e7c6f737486391
CRs-Fixed: 3133310
Introduce a new vendor command QCA_NL80211_VENDOR_SUBCMD_RATEMASK_CONFIG.
This is used to set the rate mask config to be used in mcs rate selection
per PHY type.
Change-Id: I013a547be89dac187bc48531a674f3dde8a3f6e9
CRs-Fixed: 3137604
Add support for the QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT
and QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_ID vendor attributes
in the driver.
Change-Id: I8835f363f8327315c9ec91acfb3770cd3313f572
CRs-Fixed: 3128863
While notifying the ML connection status to the supplicant, partner vdev
information will be filled in the connect response. This partner vdev info
is populated using partner link IDs. This may cause issues since it is
not guaranteed that link id information in the partner vdev is valid while
notifying the connection status to the supplicant.
To address this, get partner vdev information using vdev ID instead of
link ID.
Change-Id: I5e45b038b1fe5b6ab9c6bbb514eefb0ad4c39e66
CRs-Fixed: 3117702
Add QCA_NL80211_VENDOR_SUBCMD_MCC_QUOTA. When two or more interfaces are
active on the same band and two different home channels (MCC), the
target may allocate quota of "on channel" time for each home channel.
The target will indicate the quota information to application layer with
this event. Application may do TX bitrate control based on the
information. The user may also set the MCC quota for an interface by
using this command.
Change-Id: Ic8d8c5a5f2a6f0c55fd46394fa8e2062a37abefc
CRs-Fixed: 3101791
Currently the moderate latency level is not used. Rename the moderate
latency level to XR latency level to be used in XR (extended reality)
applications.
Change-Id: Ie5ca8983c17800131bb554dbb14f5cf94023aa1c
CRs-Fixed: 3128109
Add a QCA vendor netlink interface to start/stop periodic TSF sync
feature and also support configuration of interval value as part of TSF
sync start command. In addition, improve documentation for the related
attributes and values.
Change-Id: Ia39609a3cc72c0194fe4685e43f08f1c49f8b412
CRs-Fixed: 3108416
Currently wlan_cfg80211_mc_cp_stats.h file is present at
qca-wifi-host-cmn/cmn/os_if/linux/cp_stats/inc.
With this change, move file to qcacld-3.0/os_if/cp_stats/inc
as this file contain MCC specific code.
Change-Id: I6017e1f2b136da3a1de2965a37c56c9477941d79
CRs-Fixed: 3108258
First host checks below two things in PNO scan request:
1. Userspace sets NL80211_SCAN_FLAG_COLOCATED_6GHZ flag
in pno scan request.
2. At least one 6G channel is present in the pno scan req.
If any of above conditions satisfy, Host fills all remaining
(other than channel(s) present in pno scan req) valid 6 GHz
channel(s) to pno scan requests and set the flag
FLAG_SCAN_ONLY_IF_RNR_FOUND for each remaining channel(s).
Host sends this updated channel list via WMI command
WMI_START_SCAN_CMDID_param_tlvs->channel_list for pno scan
to firmware.
By this driver allows Firmware to scan 6G channels based on
RNR IEs only (for colocated APs reported by 2.4/5 GHz APs).
Change-Id: Ib6118c4525e9fbe233eb6a7e07a4a3345d486e8a
CRs-Fixed: 3103923
Currently driver just cancels the scan request and does not free
scan request memory if netdev is NULL or get vdev ref fails,
which leads to memleak.
To address abobve issue, free the scan request if netdev is NULL
or if get vdev ref fails.
Change-Id: Id6605e76a8c0977df93428f2aeb73c0bdfb84685
CRs-Fixed: 3107784
Add additional attributes in QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT
vendor sub command to avoid usage of unsafe frequencies on wifi
interfaces sent from userspace to the driver/firmware.
The driver/firmware shall use restrictions and power cap accordingly
to restrict the usage of these frequencies on operating interface(s).
Change-Id: Ib2234137e436f1ddfe1163aed6e1d4b291f19aa8
CRs-Fixed: 3098836
Add QCA_WLAN_VENDOR_ATTR_ACS_EHT_ENABLED flag attribute to conduct ACS
for EHT mode. The driver can consider EHT specific parameters such as
puncture pattern for ACS when this flag attribute is indicated by
userspace.
Change-Id: I9cb0b7a6bc830a5f4f01a7a7fa5212cc6b2c3a95
CRs-Fixed: 3108987
First host checks below two things in host scan request:
1. Userspace sets NL80211_SCAN_FLAG_COLOCATED_6GHZ flag
in host scan request.
2. At least one 6G channel is present in the host scan req.
If any of the above conditions satisfies, Host fills all
remaining (other than channel(s) present in host scan req)
valid 6 GHz channel(s) to scan requests and set the flag
FLAG_SCAN_ONLY_IF_RNR_FOUND for each remaining channel(s).
Host sends this updated channel list via WMI command
WMI_START_SCAN_CMDID_param_tlvs->channel_list for host scan
to firmware.
With this change, driver allows Firmware to scan 6G channels
based on RNR IEs only (for colocated APs reported by 2.4/5
GHz APs).
Change-Id: I2d9d2aac58bbc521b2476756d5919647bdc265cc
CRs-Fixed: 3103873
Add support for a new QCA attribute to pass the puncturing
bitmap as part of the DO_ACS vendor command.
CRs-Fixed: 3102366
Change-Id: Ic0e54d82e48bae695baf3be4fd388ec15f81a416
Currently, VDEV manager responses are using legacy path instead of
target_if, vdev_mgr and os_if components. As the driver implementation
is planned for converged model, legacy implementation will be moved to
the respective components.
To avoid rework, Use target_if, vdev_mgr and os_if components to process
the FW responses corresponding to the vdev manager.
Change-Id: I778f6de93481fc730383e8f8e1c604f173947d69
CRs-Fixed: 3093776
Add LOW_SPAN_ACTIVE_DWELL_TIME and LOW_SPAN_PASSIVE_DWELL_TIME
macro support to keep all 2.4g/5g active/passive dwell time
same for low span scan mode.
Disable adaptive dwell to firmware so that firmware cannot
modify dwell time.
Change-Id: Iff05dd7b37a40226c61b28a1e59ea8aa8c57cb52
CRs-Fixed: 3076163
Add support to extract the freq, cfreq1, cfreq2, PHY mode, Destination
macaddr, and channel BW values from the RTT measurement request buffer
received from the LOWI application. Pass these values to a registered
callback. Users can use these values to make some decisions on the RTT
scan.
Change-Id: Idb2232c07bbfa2946dc01e75908b9a6036597ecf
CRs-Fixed: 3060685
In case the vdev is already disconnected, the indication to
the upper layer, would have been sent as part of previous
disconnect/connect failure.
If the upper layer is in process of connecting, sending
the disconnect indication back again may cause it to incorrectly
think it as connect failure. So sending a disconnect indication
again is not advisable.
So if a new disconnect is received in INIT state, drop the
disconnect and return failure.
Also remove osif_cm_reset_id_and_src() from osif disconnect
to avoid race between disconnect complete of old disconnect
and new disconnect request. With osif_cm_reset_id_and_src()
old disconnect might also get dropped in osif and with this
fix new disconnect will also get dropped, so make sure that
last/old disconnect indication is sent to upper layer.
Change-Id: Icf7352d8904473329edff9ec124c6197f214f88b
CRs-Fixed: 3074093
Along with 11BE feature macro, check for Kernel 11be macro to avoid
compilation issues when kernel doesn't support 11be.
Change-Id: I11c8287725a25b6b4e3234a38ae61d50f293cc96
CRs-Fixed: 3066178
Modify MLO disconnect handling to issue disconnect on all links in
parallel
Also modify connect resp to accommodate ml info in connect resp
Change-Id: I57575c6ce7c8ebff7770f862dc81e7dfd20aa42d
Fill ML partners info in connect response structure of the connect
notification to the supplicant.
Change-Id: I3b972254138d0f00ef63f2b4d336d142e6d5e2ae
CRs-Fixed: 3036325
In the new wifi specification 11be mode support is added, add a new
11be dot11 mode to qca_wlan_802_11_mode.
Change-Id: I9c5238ffaac96fcdf83e7c342a053dda7fc1f205
CRs-Fixed: 3050936
Add the attribute QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY to configure the
priority of vendor scan relative to other scan requests.
Add the valid values that this attribute can take.
Also, add an API to convert NL80211-based scan priority value to internal
scan priority value.
Change-Id: I6c62166c2dd6ea0880b332496b1e4bb0b41840c6
CRs-Fixed: 3044332
This change introduces the new roam set param WMI command to set
the roam params from host to FW.
Also added a fail_bssid param in wmi_roam_result TLV to know the
roam failed AP BSSID from the FW.
Added a new vendor command event for sending roam events stats
attributes to userspace.
Change-Id: I7a08635a7912cbd940d90a2d62433296740ad913
CRs-Fixed: 3050799
Introduce a new vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS
that aims to configure/trigger the roam events from the driver.
Change-Id: Ifd9464cc8cb485890c8d171dc136d377f7a59fa1
CRs-Fixed: 3028404
From 5.11 kernel, nla_strlcpy() is renamed to nla_strscpy() since
it works more like strscpy() than strlcpy() after the enhancement.
Hence handle it accordingly in WLAN driver by creating wrapper API
wlan_cfg80211_nla_strscpy().
Change-Id: I4c5ca1738048605c842c827d1706353bc012fed8
CRs-fixed: 3060060
Populate and expose the following 320MHz spectral capabilities.
- Agile spectral scan support for 320MHz mode.
- Number of detectors used for spectral scan in 320MHz mode.
Change-Id: Ibea77d4ec8b1d9322ef82d1d48236836ffad24ec
CRs-Fixed: 3053059
Add a QCA vendor attribute to indicate agile spectral scan support for
320MHz mode. Add another attribute to indicate the number of
detectors used for spectral scan in 320MHz mode.
CRs-Fixed: 3045445
Change-Id: I4667e93e8074af122bfe9e08bededc439811afbf
Spectral scan bandwidth value that is received over NL80211 socket will be
in NL80211_CHAN_WIDTH format. Convert it into phy_ch_width format before
using it in the driver. Similarly, convert the spectral scan bandwidth to
NL80211_CHAN_WIDTH format before sending over NL80211 socket.
Change-Id: Ic3b464bff6ac62a9d0c1f915118a4ca6db416252
CRs-Fixed: 3048195
Add Spectral APIs to convert channel width values
from enum phy_ch_width to nl80211_chan_width and
vice-versa.
CRs-Fixed: 3029184
Change-Id: I60fb7fb04b943b0d70c569ff6587e5e8efd7722b
Add new vendor command to configure monitor mode packet filter
parameters which includes data/mgmt/ctrl frame types.
Change-Id: Ie5e5d35b725e3d1b617edc1c889dc269b22a3673
CRs-Fixed: 3025489
Add support to configure spectral scan bandwidth as provided by the user.
Validate the user configured value before applying it. As the spectral scan
bandwidth is an optional parameter, when the user doesn't configure it, use
configure the spectral scan bandwidth to the maximum value supported by the
target for the current operating bandwidth.
Also, populate the spectral scan bandwidths supported for different
operating bandwidths on different targets.
CRs-Fixed: 3042424
Change-Id: I266aa5489b0ce5c149968067a06e1cc65bb4e3b7
