Firmware doesn't fill any roam fail reason in roam success case,
which would result in having fail reason value as '0'.
But driver ends up converting the reason '0' to 'unknown'.
So, convert the roam fail reason only in roam fail case.
Change-Id: I0fea2788673e049fd078bcc6200b9612e538ee37
CRs-Fixed: 3632850
In API extract_roam_11kv_stats_tlv(), band info value is
fetched from wmi_roam_scan_info. This results in failure
during active mode when single tlv is sent for each event
as wmi_roam_scan_info tlv is not populated for event
expect for roam specific events.
Extract band info from wmi_roam_neighbor_report_info
tlv for neighbor report and BTM events in order
to overcome the above mentioned issue.
Change-Id: Ie53ec36ea1b788219b33f0956b489d5bbe0bb9b0
CRs-Fixed: 3631719
In the MLO-MBSSID test, STA can request information of
non-Tx BSS through Tx BSS by configuring non-Tx BSS MLD
ID within the ML probe request that is invoked as part
of scan request. Add support to configure MLD ID in
scan start params to FW.
Change-Id: I4a6debf6c3ec830fbe3aee1d3aa60ad7218cbcd6
CRs-Fixed: 3591596
Add NULL check for scan_info pointer to avoid NULL pointer deference
in function extract_roam_trigger_stats_tlv().
Change-Id: I42f957d00b1ad27845782f099865210eb4ba24a0
CRs-Fixed: 3624591
Add support for wmi service tid to link support.
Fw will indicate t2lm support using this bit.
CRs-Fixed: 3605468
Change-Id: I4d5f4e587da1cf362dcfaf2d89e7af176a115dcf
This change is to add wmi interface for sending channel
switch Announcement event status indication from host driver.
Change-Id: I4b22280e4e4c85ebf54394c80d4fefa62eef4b2d
CRs-Fixed: 3616927
Send standby pdev/radio which is expected to be up while
in powersave mode to FW, to switch master control for
timers.
Change-Id: I4b48d93859359d1b6aee0b9993fd1bd3bff863f2
CRs-Fixed: 3621705
In the scenario about MLO 5 GHz + 6 GHz and 6 GHz is non-tx AP in
MBSSID, if DUT tries to connect 5 GHz link as assoc link and uses
the scan entry generated from 5 GHz beacon. Then there is no info
about profile index and count in the scan entry and these info is
necessary for firmware when vdev up.
To resolve this issue, get the info from 6 GHz scan entry if it
exists.
CRs-Fixed: 3616899
Change-Id: Ic9bf9bc107c3486be1e87ea2c19c5d388ca41883
A customer has reported an issue regarding the FW not asserting when it
receives the WMI_FORCE_FW_HANG_CMDID from the host. We need to confirm
whether the FW actually receiving the command or it is stuck in the WMI
command queue because it’s full.
To do this, adding some prints along with the timestamps in the WMI command
path and WMI command Tx completion path.
Change-Id: Ib4d6423365a150f91597a9d83ab8a85a053de777
CRs-Fixed: 3598136
Currently in the driver, we hide 2nd, 3rd and 4th bytes of the
MAC address in GKI builds. Since 2nd and 3rd bytes are needed for
debugging, hide only 4th and 5th bytes of the MAC address.
Change-Id: Ia432bb0d40e0a09b56e581f192a810e727127d3a
CRs-Fixed: 3616774
This reverts Change-Id: I65efe5601e15055c5407f085e1fdcae5b28d6b81.
Its okay to fail send request instead of triggering crash recovery.
Triggering self recovery is only for fatal errors which can’t be
recovered without doing SSR.
Change-Id: I59532074c361bba4412ceb66f3f0e1e99d73bf06
CRs-Fixed: 3617795
Register event handler for WMI_MLO_LINK_STATE_SWITCH_EVENTID.
Add target if event handler for the
WMI_MLO_LINK_STATE_SWITCH_EVENTID event, and register
corresponding mlo manager callbacks.
Add extract API for link state switch event parameters received
Call the diag event API from MLO manager post extracting the
event
Change-Id: Ib588ee87a5c37c6a34c86ce8cbf134a273c6461b
CRs-Fixed: 3610041
Add mlo teardown support for standby active mode in
mlo setup sequences and wmi
Change-Id: Iaa727527c53ff0ad6c7682e039ef23fa537e1ae0
CRs-Fixed: 3613367
Implement handling of mlo sta standby csa beacon
and initiate the transmission of a link bss request
command tlv to the firmware for standby link.
Change-Id: Ibdf903c69757b47f301ab9fa7c563407915532d6
CRs-Fixed: 3605764
Change is made to add debug prints for VDEV start
and peer assoc commands sent to FW.
This change is made to help with debugging logs.
CRs-Fixed: 3611450
Change-Id: I40a0991330edd4ba71b7b71f2f7cf36364f4f365
Extract MLO band data from roam stats event for
BTM query, BTM request and BTM response logging.
MLO Band refers to the band of the link involved
in MLO conenection.
Change-Id: Ia60821f7973fe1d39eb824a3eac7791672503084
CRs-Fixed: 3583688
Modify roam_scan_stats_tlv and roam_scan_ap_stats_tlv
to introduce mlo specific elements for Roam scan start
and Roam candidate ap logging.
Change-Id: I8e72abc3b888614faf533fd8086cf73a29c26f85
CRs-Fixed: 3582433
Firmware sends PEER_OPER_MODE_CHANGE event to host in SAP
mode when a connected client indicates upgrade/downgrade
of its bandwidth.
Host needs this data as any further SAP bandwidth
upgrade/downgrade should honor the indicated bandwidth for
that specific peer.
Change-Id: If15f491fd970486d8e84d1845866688d837ea2b4
CRs-Fixed: 3604865
Add workqueue destroy in the wmi detach for the wmi_rx_diag_work_queue
to avoid the system memory leak.
Change-Id: Ic183ddaa2e53292a50e0b379877a92ddcaf45b02
CRs-Fixed: 3597405
Currently the T2LM timer is maintained by host.
Code change made to add support to run the T2LM timer in FW.
CRs-Fixed: 3594141
Change-Id: I7eee4800f68b07d5492a0336e3fe8e0db17d2020
Added change to handle TxBF standalone sounding CQI data.
1. Define and handle structure to support new TLV for CQI data.
2. API to extract new meta data TLV added for CQI data
3. API to handle processing CQI data.
Change-Id: If6e654fc03cc5c150b85bc9af487c58b77d78e1d
CRs-Fixed: 3594811
Hopping radar happens on whole band, hope all DFS sub channels are put to
NOL, but F/W only reports single radar event on special freq to host.
When DFS puncture enabled, sub channel marking is enabled, host only put
single affected 20M sub channel to NOL instead of all current bonded sub
channel, AP still stays on current freq for valid puncture bitmap
instead of leave DFS freq.
If the radar is a frequency hopping radar that truly hops over entire DFS
band, then the AP and clients are best served by moving out of the DFS
band. But it could well be that only part of the band is used. It is
difficult to find product specifications with info on the total bandwidth.
Mostly military systems use frequency hopping to avoid jamming. So a middle
ground would be to put full bandwidth of current AP to NOL for FCC type 6
frequency hopping radar.
When frequency hopping radar happens, F/W set flag that full bandwidth need
put to NOL in new added tlv radar_flags of event
WMI_PDEV_DFS_RADAR_DETECTION_EVENT, When find the flag is set, host will
put full bandwidth of current AP to NOL even sub channel marking is
enabled.
To avoid compatibility issue between old/new F/W and new/old host, add a
F/W service bit wmi_service_radar_flags_support and host service flag
is_full_bw_nol_supported.
If the wmi_service WMI_SERVICE_RADAR_FLAGS_SUPPORT is enabled by FW, host
shall set/unset a bit in the host service flag is_full_bw_nol_supported
based on host capabilities. This host service flag is then sent to FW via
WMI_INIT_CMDID.
Change-Id: I6e280ca4ab00dce97c5aec90c7a4b4fc7c4a440a
CRs-Fixed: 3595476
Add support to send TWT IE in assoc/probe rsp to fulfill WFA requirement
FW sends TWT IE in mgmt rx event for probe req and assoc req. Send this
IE in probe rsp and assoc rsp. This change takes care of extracting TWT
IE in mgmt rx event.
Change-Id: I1a97eb58c03f76c7ced31349dc0e3b4a908ceda0
CRs-Fixed: 3585625
Add support to parse the Max ML Peer ID's parameter received from target
capabilities and update the parameter in global MLO context.
Change-Id: I4118d288a312dc4a18182caf765b0ded014b985a
CRs-Fixed: 3556542
Update version for vendor request 1 and vendor request 2 as
below:
vendor_req_1_version: WMI_HOST_VENDOR1_REQ1_VERSION_4_00
vendor_req_2_version: WMI_HOST_VENDOR1_REQ2_VERSION_3_50
Change-Id: Ib8ff2596c415453c26de3d7d26dce5dceed30556
CRs-Fixed: 3589711
To support group NDP security, WiFi-HAL and firmware introduces
two new parameters (csid_cap and gtk_required) in NDP initiator
request, responder requestor and NDP indication event.
Host driver will retrieve the CSID capabilities and GTK parameter
and parse it to firmware in NDP Initiator and Responder request
TLV. Also, driver extract these parameters from NDP indication TLV
and will pass to Wifi-HAL in vendor event.
Change-Id: I23483141219e4224bb76ed209aee46e131eaa747
CRs-Fixed: 3583154
When WoW enable cmd has been sent to F/W, but no ack from F/W yet,
UNIFIED_LINK_STATS_GET_STA is sent over WMI, assert will happens.
To fix it, once WoW enable cmd has been sent to F/W, don't allow
UNIFIED_LINK_STATS_GET_STA sent over WMI.
Change-Id: I13271e88310bc510a9c7668d193f6e776554a442
CRs-Fixed: 3585971
Add support to extarct sta stats from WMI_CTRL_PATH_STATS_EVENTID
by extracting wmi_ctrl_path_sta_rrm_stats_struct data
Change-Id: I7235b8cb0237d828b0fe5e5eab0feadc016d9269
CRs-Fixed: 3583920
Modify wmi_nofl_info_high definition to print only if
QDF_TRACE_INFO_HIGH_NO_FL debug level is set.
CRs-Fixed: 3570322
Change-Id: I879a9d917ff698aeb6b3e53a85c765a74a902b36
Includes changes:
1. Save frequency values from EXT and EXT2 events to psoc object
- wireless_modes, low/high 2 GHz chan and low/high 5 GHz chan from EXT event
- wireless_modes_ext, similar frequency range fields with _ext from EXT2
event. Frequency range fields with _ext are non-zero when a radio supports
overlapping frequency. Eg.Radio that supports 5 GHz full and 5 GHz high band will
have low/high 5 GHz fields populated with primary band values in EXT event and
low/high 5 GHz fields are populated in EXT2 event with secondary band
values. These values are stored in tgt info for later use.
2. Modify regulatory APIs to get and set the wireless modes in reg
component
3. Retrieve frequency fields from EXT2 event
Change-Id: I49ebcc7ee7b26bd115f37abc8cb5b6fa5a415eda
CRs-Fixed: 3576551
Add support to handle WMI_ROAM_SYNCH_KEY_EVENTID.
WMI_ROAM_SYNCH_KEY_EVENTID is received after roaming to 3 Link
MLO AP when standby link is supported.
Add changes to register handler function pointers and parse
the event.
Change-Id: Iee17560f9f1f3242ef512a550764a9c64319b67f
CRs-Fixed: 3571673
Prepare and Send WMI command to fw to set the rf path. Also, add module
ID for rf path switch for qdf log prints.
CRs-Fixed: 3568221
Change-Id: I7ef0ffe66eaed837424699641d3e5b8537cd0304
