Add INI parameter for packet capture mode
"packet_capture_mode" - ini to set packet capture mode.
Change-Id: Ie60c142af753c65b44aa0018440e43a215e51a27
CRs-Fixed: 2614578
idle_roam_rssi_delta - This threshold is the criteria to decide whether
DUT is idle or moving. If rssi delta is more than configured thresold
then its considered as not idle. RSSI delta is entered in dBm. Idle
roaming can be triggered if the connected AP rssi change exceeds or
falls below the rssi delta and if other criteria of ini
"enable_idle_roam" is met.
To enhance idle roaming, idle_roam_rssi_delta default value is changed
to 3.
Change-Id: I9a5b06081d59d8502c40df0485c2b997cbcb2b80
CRs-Fixed: 2619436
AP has less keep alive timer than STA, so AP is kicking out the STA and
sending the deauth.
To resolve this change CFG_INFRA_STA_KEEP_ALIVE_PERIOD_DEFAULT value from
60 to 30.
Change-Id: I0522071bc634b029178de6e09c11d237351a334d
CRs-Fixed: 2616279
When application issues NDP end to terminate an NDP connection,
host driver sends a request to the firmware and firmware
terminates the NDP by sending NDP end frame to the peer.
Currently, driver returns immediately after posting request to
the firmware. Application might issue NDI delete immediately
after returning from NDP_END request.
But firmware might take some time to complete the NDP termination
and send NDP_END indication to driver.
When driver tries to delete the NDI before receiving NDP_END
indication from firmware, it causes inconsistency in firmware as
the NDI on which the NDP is parked is freed.
So, wait till the NDP_END indication comes from
firmware(or timeout happens) before returning from ndp_end request
context.
Change-Id: Ied7ed36451ef007e38f67d48c54290b9dd674f54
CRs-Fixed: 2616018
Currently there is no inis for NAN component:
1. To configure the keep alive period for the
NDI interface.
2. To enable/disable discovery of NAN cluster with
Master Preference (MP) as 0 when a new device is
enabling NAN.
Add ini support to configure above mentioned values.
Change-Id: I47b67eb89fb8849960a9f492d2909e45b96308f3
CRs-Fixed: 2617839
This patchset adds the FTM TIME SYNC component in
target_if to register the ftm time sync wmi events/cmds.
Change-Id: I4ea14266a912c9d261a67809556774860b5ddab1
CRs-Fixed: 2617055
Currently there are lot of duplicate logging. Identify and
reduce those logs that are not absolutely necessary.
Change-Id: I649ce3bec8c3c8542fe9edd08907da9ab01fa948
CRs-Fixed: 2617504
Add support to customize DSCP-to-UP map table and send the
customized map values to FW to update its corresponding
map table.
Change-Id: Ibe9704a90468c898dd2e60fdf83a271152f654ce
CRs-Fixed: 2616247
In case of successful wow enable ack from FW for system
suspend call cdp wow ack response process, so that dp
layer will take care of required operations before system
goes to suspend.
Change-Id: Ibc5bf8d62aa055c9c8c7242c00abc3b696bb0051
CRs-Fixed: 2608980
As part of new requirement WLAN subsystem needs to perform thermal
mitigation action as per the thermal state of the device. The
wifi hal sends vendor command QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD
with the thermal level parameter and wlan host performs the required
appropriate action. wlan host driver maps the thermal level to
corresponding duty cycle off percent value and duty cycle value,
send WMI_THERM_THROT_SET_CONF_CMDID cmd to FW.
Make changes to perform vendor command handling, mapping thermal level
to duty cycle value and communicating the thermal information to FW.
change-ID: I77175048c817ab755cdb838018e414ef3ee0b112
CRs-Fixed: 2610395
Add a new INI parameter "nan_separate_iface_support" to
indicate firmware that the host driver supports separate
interface for NAN Discovery.
Change-Id: I6fb313b02c5f3a05638e85494051fb003b2dd867
CRs-Fixed: 2612006
In FTM mode, no peer is created in the host. Currently, since
peer_unmap_conf_support feature is enabled, FW is expecting
WMA_SEND_PEER_UNMAP_CONF from host to remove the peer Id from AST.
But host never send this WMI CMD in FTM mode.
Disable peer_unmap_conf_support in FTM mode which allow FW to
delete the peer Id without any WMI CMD expectation from host.
Change-Id: Idf9082adc81187346563f3aedf1f1657164f03cc
CRs-Fixed: 2608929
arp_ns_offload and gtk offload command are being issued for NaN mode
vdev. NaN mode vdev does not support ARP_NS and GTK off load features,
so disable them when in NaN mode.
Change-Id: Iab11c92bb5da4004b62e642342a386f532832509
CRs-Fixed: 2608618
Add support to make event WMI_ROAM_PMKID_REQUEST_EVENTID as
wakable in FIPS case.
In FIPS Enabled case, for roaming Firmware sends PMKID request
to host as firmware is not supposed to do crypto functionality
with FIPS enabled.
Change-Id: I09b6b68f77ba75f9e5519ff18017c95d16771f52
CRs-Fixed: 2513790
STA considers RSSI delta configured by the user along with other
parameters for roaming.
RoamRssiDiff is the number of units (typically measured in dB) AP2 is
better than AP1. STA roams from connected AP1 to AP2 if the RSSI value
of AP2 is greater than AP1 by configured ROAM delta value.
Max limit of RoamRssiDiff is increased to 100 from 30, so user can set
roam delta from 0 to 100 using command SETROAMDELTA.
Change-Id: I69b783ebe5ec971bb62cbac8a34065d52fc25422
CRs-Fixed: 2609589
Update the mlme_get_roam_fail_reason_str() to return
correct string for new roam failure reason enums added.
Change-Id: I24983149fdcd8a0935eea9670832944638c33179
CRs-Fixed: 2607545
Currently many layers store the datapath handles i.e.
pdev and vdev handles and use them for passing as an
argument to the CDP APIs. This gives way to possible
race conditions, where the datapath handle provided by
the outer layer might be a stale pointer, which in turn
leads to unexpected results.
Remove the storage and usage of all the datapath handles
from the layers currently using them.
- cds_context
- vdev objmgr
- pdev objmgr
Change-Id: Icf24bd3792af203d1a06e153f0badd6e7405559f
CRs-Fixed: 2602199
Currently the driver sets the connection update
flag in case of the hw mode cb when the set
hw mode is done, irrespective of the status
code sent by the FW. This leads to the completion
for wait for event and the caller to the current
connection update would get a wrong expectation
that the hw mode requested by it was set, which
would not be the case when the hw mode is not set
according to the user or the set hw mode was
rejected by the target itself.
Fix is to set the connection mode only when the
status is success or already the HW mode is set.
Change-Id: Ic7257b0be5a4bcdaecffb788cf3394b06ddfd5e5
CRs-Fixed: 2604062
Use newly defined QDF API in CMN qdf_is_driver_unloading() to check
if driver unload is in progress in DSC.
Change-Id: I2958c6cc3ee6f2ac4302e2dbbf1c68d986fea175
CRs-Fixed: 2605706
Currently cdp ops are given pdev/vdev handle
as its arguments, which is directly accessed
in those APIs. This can cause a race-condition
in access of the respective handles, if it has
been deleted in parallel.
Hence as a part of cdp convergence, pass only
the pdev_id/vdev_id which will be used to get the
respective handles and hence avoiding unwanted
access of the handles if it has been deleted.
Also deleting few ops which stores and retrieves
such handles and adding ops to set/get pdev params.
- txrx_set_safemode
- txrx_set_drop_unenc
- txrx_get_pdev_param
- txrx_set_pdev_param
- wdi_event_sub
- wdi_event_unsub
Change-Id: Ib3511cbdead75b30e899dbf00f936ffdae316b71
CRs-Fixed: 2541657
Previously vdev trans will be rejected if psoc in trans. but
it causes issue when __hdd_psoc_idle_shutdown is in psoc trans,
if ifconfig comes here, the ifconfig will fail.
Add checking if psoc trans in driver recovering and unloading,
if yes, it will be safe to reject vdev trans, otherwise, we should
let vdev trans waiting for psoc trans.
At the same time, we also need to make sure driver state has been
set before psoc trans when unloading.
Change-Id: Ic47eebef76b8eadc90780b74f75d4ebef73b822d
CRs-Fixed: 2601435
Enable p2p go gc force scc by adding logic to check the connected
p2p gc when checking concurrent channel interfering and restart p2p
go if needed.
Change-Id: Idd01fbc2a358b463568844a420e1132355c1de4e
CRs-Fixed: 2604955
This reverts commit I1adb8ead32a0d45a34f72590c33309b17d6c80c0.
Nan offload supported is now supported.
Change-Id: Ic99aa886c82dcf4d9c68f658080bd800117cce87
CRs-Fixed: 2600602
6Ghz channels information is not used by legacy OEM apps example
"lowi-server" having no support for 6Ghz channels.
Hence "oem_6g_support_disable" INI is added. By default INI value is
1. 6Ghz supported OEM applications sets INI value to 0 and gets 6Ghz
channel information from driver.
Change-Id: I2650e6ad2976b64e46ab0143b2bafc2df2343e94
CRs-Fixed: 2597651
In wlan_mlme_configure_chain_mask(),mlme_legacy_err is
updated to mlme_legacy_debug,as its not an error condition.
Change-Id: Ibdf33124ee970bcfcc9d57df9f3b3fc6990072fe
CRs-Fixed: 2599510
If the request is SBS action and the HW doesn't support SBS,
return QDF_STATUS_E_NOSUPPORT. The caller will continue to
connect/start_ap instead of failure when
policy_mgr_current_connections_update return
QDF_STATUS_E_NOSUPPORT.
Change-Id: I158f90c13e2685697b82c874a247883f21f013cb
CRs-Fixed: 2602194
Add a check if list count is non-zero before deleting the node
from IPA tx descriptor list.
Change-Id: I9913c636107686755ffc5da2b585028a4be7a1e9
CRs-Fixed: 2601601
In case of STA + SAP ipa pending tx timer is started when last
SAP client disconnects. Again if client connects back timer is not
stopped at pipes enable. Later some time if suspend kicks in and
during bus suspend if there are no ipa tx pending ipa pipes are
disabled. This leads to issues such as data stall, invalid IPA
doorbell register access. So reset the timer during ipa enable pipes.
Change-Id: Id6034596f52f98c793674c9d9e5f7918c5c3d455
CRs-Fixed: 2598559
lim_is_pkt_candidate_for_drop() uses sta_ds to update last assoc
and deauth/disasocc received time without taking any lock for
sta_ds. deletion of sta_ds in pe_delete_session before accessing
sta_ds in dph_lookup_hash_entry can lead lead to Assert.
Similar is the case with sta_ds->last_assoc_received_time and
sta_ds->last_disassoc_deauth_received_time.
Fix is to use peer_priv instead of sta_ds and update
last_assoc_received_time and last_disassoc_deauth_received_time of
peer_mlme_priv_obj. In this case refcount gets increased for valid
peer and peer won't be deleted until lim_is_pkt_candidate_for_drop
releases the ref count of the peer.
Change-Id: I9daf31f9dd7b509eaf38a93078bb7418605b1c74
CRs-Fixed: 2598841
According to FW, DFS phyerr offload should be enabled before vdev start,
otherwise FW can't start DFS phyerr offload function.
Do not send DFS phyerr offload disable wmi command before vdev stop, and
FW will handle all the necessary cleanup in vdev stop wmi command.
Without DFS phyerr offload disable wmi command, DFS phyerr offload is
enabled before vdev start.
Change-Id: Id6275e9716afb34316cf46b69dd0b4f82b73ac5d
CRs-Fixed: 2598263
Set the default software retry limit value to 16 and fix the typo
in configuring the non aggregation software retry limit.
Change-Id: Ia6ef7cc39f47ef91c2c338e48561e0275445750f
CRs-Fixed: 2599467
