Assign default channel mapping to three channel voice Tx
devices when the topology specific info cal data is NULL.
Change-Id: Ic9d572edc1d7de07a2bd5e11d82f875368c35854
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Switch to DLKM for all audio kernel modules.
Change-Id: I6a96023a21f655f873531af9ace81f2b01eb0f58
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Add support to set number of channels and channel mapping to DSP
as per the info received from ACDB files along with topology
for a device in voice usecases instead of reading from
backend configuration. When topology specific channel info is
not supported, send the default no of channels and
channel mapping as per backend to support backward compatibility.
CRs-Fixed: 2110934
Change-Id: Iad512474fc25c906d97513f6648cd8ba6244eda1
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Allocate contiguous memory for version information instead of splitting
it across the stack and heap to centralize memory and improve
readability.
CRs-Fixed: 2104576
Signed-off-by: Siena Richard <sienar@codeaurora.org>
Change-Id: Id7b5942522da6312da57bfef3d3c0b55934fe1d7
In Stereo EC reference, mute is observed in VPRx output
of 2nd channel when only speaker device uses custom MFC topology.
When handset and speaker use the same custom topology, issue is not
observed. Because when DSP VPRx module creates the
custom topology with handset configuration (1 channel and
center channel mapping) and device switch to speaker occurs
MFC conversion from center to left and right channels is successful.
But in case where handset uses default topology, when device
switch to speaker occurs, VPRx creates the custom topology
with speaker configuration(2 channels and left mapping). So,
when MFC config is received, only left->left mapping is done which
leads to mute in right channel.
Fix is to send the channel mixer configuration to MFC module
so that both left->left and left->right mapping is done.
CRs-Fixed: 2102374
Change-Id: If9be09866615e6623e78f48b9841eb068c825992
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Assign channel mapping for Quad Mic voice use case
in channel info command during voice setup
as DSP requires channel mapping to be sent with
default values.
CRs-Fixed: 2097341
Change-Id: I661f845c26f8639e5e8dffa430ecc8cb3b3e8780
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Propagate the changes based on latest snapshot
for audio kernel source tree at below cutoff of
kernel msm-4.9 -
(040750bfa78 -
"Revert "ARM: dts: msm: Add DT node for aop-qmp
clock controller on SDM845 v2"")
CRs-Fixed: 2104096
Change-Id: I0927c40b3a188dbf892e7ec4c1c7810953724929
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Propagate the changes based on latest snapshot
for audio kernel source tree at below cutoff of
kernel msm-4.9 -
(aed56b2df75 - "drm/msm/sde: update te vsync enable sequence change")
Change-Id: I7ed5102146986b81e5cb9ca55432360b3549b60c
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
