Retain ds ring indices across wifi restart to avoid
edma hang. Fetch the indices from ds module and set
the corresponding ds ring indices.
Change-Id: Ia299a7006166aef096c7d2c1f65f6bef65415a37
CRs-Fixed: 3332152
The MSI address and data information for Direct Link
copy engines will be available once the WiFi driver
on LPASS is initialized. Add support to configure the
IPCC address and data values into Direct Link copy
engines at runtime.
Change-Id: I5e7dff90c2f1ff764462c235deb5795ed019a16b
CRs-Fixed: 3316679
Add support and ops for initialization and
deinitialization of Direct Link refill ring.
Change-Id: I2c7018c4f8411fb7a590cfbb8b991f9152b22397
CRs-Fixed: 3316656
Add support to read TSF2 and TQM scratch regitser in the HAL layer
for WKK v1 and v2 board.
Change-Id: I0ef5e8cf4e06c0b5c98169252a81f70989285d2d
CRs-Fixed: 3321782
Currently the monitor mode filter settings are set
for both the PMAC. Hence it is possible that the
non-monitor PMAC (the PMAC on which monitor vdev
is not running), can receive packets and forward them
to the monitor destination ring.
The above scenario will lead to a ppdu_id mismatch
when reaping the monitor status ring and comparing
the ppdu_id in status ring with the one in monitor
destination ring, since monitor status ring will
have ppdu_id from the PMAC on which monitor vdev is
running, whereas monitor destination ring will have
packets from both the PMAC.
In order to mitigate the above issue, detect the
packets in the monitor destination ring, which are
not from the PMAC where monitor vdev is running, and
drop them.
Change-Id: I32392ceeadffd9cb7a4dd76336004a9dcbb99404
CRs-Fixed: 3318036
certain BE specific HAL APIs were only initialized for
KIWI chipset but not for WKK. Now moved all these APIs
under beryllium generic initialization.
These APIs are mainly used in de-frag pkt handling.
CRs-Fixed: 3294784
Change-Id: I6611f1b7ef80b432d24a490ba65880dd55539137
1. Changes to get correct write address in hal_get_window_address_5332.
2. Fix for monitor init crash - Added dummy entries to match the
ring_id.
Change-Id: If59b1c231d4595a95e7c1f02de1dbe0ce27a8805
CRs-Fixed: 3268933
When FW was enabling WOW, a ring HP update interrupt is seen
which led to fw crash.
This change records any PCI writes that went through during
runtime suspend from host.
Change-Id: I3c44760ebaf49a131b483813522fe3e451957215
CRs-Fixed: 3280166
For Beryllium LMAC rings, hal_get_srng_ring_id() provides the ring IDs
separately per each LMAC only if that LMAC ring is a destination ring
(This is done to use a common source ring for the DMAC rings).
But the ring IDs for LMAC source rings like DIR_BUF_RX_SRC_DMA_RING are not
being provided separately per LMAC. As a result, these ring IDs in
split-PHY mode are colliding for the 2 LMACs.
Fix this by doing the following.
- Mark the DMAC common rings within the LMAC rings.
- Provide ring ID separately per each LMAC if the ring is an LMAC ring
but not a DMAC common ring.
Change-Id: Ifdae085b5784a03763abfc4edb42d94593e3ea21
CRs-Fixed: 3282702
set register WCSS_UMAC_REO_R0_MISC_CTL 6th bit to 1
to enable reo wref from fw side.
Change-Id: Ib8d4a2f6e7f598d45ba2b2c628ed6f3929fc3337
CRs-Fixed: 3273558
Hal layer changes to handle Umac post reset
and post reset complete events from firmware.
Change-Id: Ib25427930aab25650731c87b38e2ef7e47ae98d9
CRs-Fixed: 3267222
In QCN9224 fetch the peer meta data from the msdu end tlv
instead of MPDU start
Change-Id: Icd9420cd83e06abe5e54e9e05cc8cbf8d8312ae1
CRs-Fixed: 3245626
Add support and handle tx monitor full buffer payload and
other minior fix include change of name for uniformity.
Change-Id: If401ecd5e1c6263584fa7013df672459c883ca8b
CRs-Fixed: 3215244
Change macro IPA_WDI3_RX_TWO_PIPES to IPA_WDI3_VLAN_SUPPORT to represent
the feature supported under this macro
Change-Id: Ie1e387d641052cd5690c63f0c1216f4852544605
CRs-Fixed: 3250264
1. Changes to move hal_tx_config_rbm_mapping_be function from common to
device specific as it has ppe related snippets.
2. Changes to remove all PPE related codes in QCA5332 hal code.
3. Changes to correct macros according to fw_hrs.
4. Changes to move functions with device specific Macros to header files
so that it gets compiled with respective device's FW headers and gets
correct Macros
Change-Id: I479b406f318aa42d2b1032349aaf42d95b8c18e5
CRs-Fixed: 3235966
In IPA offload, both tagged and untagged traffic cannot be handled with
a single rx pipe. Hence, add support for 2nd RX pipe for tagged and
untagged traffic respectively.
Change-Id: I77ff633327696f66df42fb592492321c1591646b
CRs-Fixed: 3226021
Add support to track the high watermark for the number
of entries which are used at any given instant. This helps
in identifying if the ring size is sufficient or is being
full for certain use-cases.
Change-Id: Id3ffa52c653696699fbcfbb556a815d5f7908863
CRs-Fixed: 3235115
In some cases we need to classify frames accordinging
to l3 type. This change mainly focus on this issue.
Change-Id: I4bc49a808a02b4bc8c65f920690922045d65e739
CRs-Fixed: 3198481
Currently 11be msdu rate statistic is not supported yet.
Another issue is: HW reported pkt type value 6, while host
SW defined 11be type DOT11_BE (value 5), they are not matching.
DOT11_BE value 5 is referred in monitor mode and otherwhere,
so do map and conversion in host sw side.
Change-Id: Ic5c2dd2a35cbe0ecd6430f007b6e7e02ece40998
CRs-Fixed: 3230900
Direct DMA source ring type has two rings where ring0 is
used for Spectral and ring1 is used for CFR. The current
hal_srng_ring_id do not have the ring_id defined for CFR,
which leads to wrong ring_id populated for TX MON feature,
which collides with CFR ring.
Fix the same by defining ring_id for CFR.
CRs-Fixed: 3220401
Change-Id: I778cea533a1907ae6cd94f63734ca6c967891b9d
For QCN9224 target, All the MIC failures are reported
as decrypt error from FW.
So, added changes to handle MIC failures for QCN9224
target .
Change-Id: I32e616e01e3cd6e76ef105d73fd8a87ce2c81cb9
CRs-Fixed: 3192749
The original BA window size given from CP might > max DP supported,
add sanity check based on HAL target allowed.
Change-Id: Ibadaddeffe65165a89d580d8a5cbf5f7c724c809
CRs-Fixed: 3193852
Shadow config v2 can support max of 36 shadow
registers only. For KIWI target, there are 40
shadow registers supported.
Hence add support to send shadow config v3
for KIWI.
Change-Id: If57e6597397da3e239f25a6c0cc24f8fd37dcdf1
CRs-Fixed: 3167758
1. Since peer id is reused for reconnection in MLO case,
old entries for queue desc addr is cleared. Clear the reo
internal storage and reset it back on client connection.
2. Send Qref feature WMI cmd to FW to enable the feature.
Change-Id: I6705ce121c8c25d9a2ace039dab21312fa5ea4b1
CRs-Fixed: 3156642
Add support for tx monitor flush/drop/truncated handling
and few minor fixes from txmon
CRs-Fixed: 3158502
Change-Id: Ic13476984cd591a381941cfa1501307e9cca2b5a
Currently in some case we are receiving non error packets on REO2TCL
ring, which is causing issue.
Fix is to set DEST_RING_MAPPING_0 to SW1 for REO dest ctrl
register, So that non error packets with reo_destination_indication
with 0x0 in the reo entrance ring will be routed to SW1 ring.
Change-Id: I67f78f35e7dba899943307902d99d0325a60498f
CRs-Fixed: 3150186
Add a separate APIs to configure RxDMA and RXOLE
configuration to enable the PPE based routing.
Change-Id: I95b8fbb361402bc04fc1f38aa8b0dbc6f99f4f06
CRs-Fixed: 3147720
Add feature support to tag first packet that wakes up HOST from WoW.
rx_pkt_tlv.rx_msdu_end.reserved_1a field is used by TARGET to meet
such request.
Change-Id: I3d37e13e8cff49bc4f622d3070a19e4c4be56417
CRs-Fixed: 3137621
Added HAL specific api to support tx monitor,
1. to get buffer address
2. get number of users
3. get corresponding structure to handle tx monitor and
4. parse limited TLV tag.
Change-Id: Ic354c76b3bcf5fa454db973c2aa4ee5f9c1b4208
In WIN BE chipsets, replace the REO tid
queue programming in FW via WMI with writing to a
Host managed table shared by HW and SW. REO HW will
pick the tid queue address from the table indexed by
peer id and tid number.
Change-Id: I8107ca5116425538329b11ae3519f02b32573bac
Add function pointers to free buffer address stored in status buffer
and support tx monitor in legacy and Waikiki flow.
Change-Id: I28612d388009292ff751fe514183fb801909f485
- Fixes for compilation issues after enabling
monitor 2.0 support.
- change copyright year for all files in the chain.
Change-Id: I885e257bd8ca83850656d8a1f408c1bc34920d7a
CRs-Fixed: 3086483
Add 2 hal soc ops, hal_msdu_desc_info_set and
hal_mpdu_desc_info_se for berilliyum datapath.
Attach hal_rx_msdu_ext_desc_info_get_ptr_be to its function
pointer.
Get reo queue descriptor address as a 5 byte value as in
beryllium datapath it is being obtained from rx packet tlv.
Change-Id: Ia58597384e1a3d5eec493b865a88bab4f209502d
CRs-Fixed: 3084532
In BE architecture, HW provides basic vdev stats support for upto
48 vdevs. For each vdev, there is vdev_stats_id which represents the
id of this vdev on HW. This vdev_stats_id is assigned by host and
is conveyed to HW at the time of REO TID Queue setup for the peer.
Add logic for allocation and deallocation of vdev_stats_id and
convey this id to HW.
Change-Id: If5611bf54d057ccf71c6444b5c79a26eb28df87e
CRs-Fixed: 3067843
Rx patch changes for multichip MLO
1. Create ini for rx ring mask for each chip
2. Configure hash based routing for each chip based
on lmac_peer_id_msb
3. Peer setup changes to configure lmac_peer_id_msb
to enable hash based routing
4. Rx Replenish changes to provide buffers back to owner
SOC of reo ring
Change-Id: Ibbe6e81f9e62d88d9bb289a082dd14b4362252c4
Changes needed for MLO soc attach to pass chip_id,
dp_ml_context from upper layer.
This change also takes care of assigning appropriate
RBM id for IDLE link descriptors based on chip_id.
Change-Id: I8f5f08c524d91942e6e458f048700b7bdd900107
Added an API to do a batch invalidation of REO descs
saw an improvement of 40 to 45 Mbps.
Note: this change is applicable only for cached
descriptors
PINE with Default driver: 3189 @ 100% core-3
PINE with skb prefetch: 3469 @ 100% core-3
PINE with skb pre + batch inv: 3506 @ 100% core-3
Change-Id: Ic2cf294972acfe5765448a18bed7e903562836c3
