FW sends Spectral scan chan info TLV in WMI_PDEV_SSCAN_FW_PARAM_EVENTID
event to indicate the channel information for a spectral scan session.
Add support to process the TLV and update the spectral host data structures
accordingly.
CRs-Fixed: 3044162
Change-Id: Ibbf7f6bbbb267123bbdf44bcfffa2cfb1c2926df
With this change add log with scan channels list dump to print
if NAN is enabled or not for any frequency.
Change-Id: I81f5017c7f146d2c7bd227601ae320d9cc67f82f
CRs-Fixed: 3042903
On Beryllium architecture, PHY DMA applies a 32-bit byte swap to assist
in efficient Host reads when connected to a big-endian Host.
This is done to avoid byte swapping at the Host.
So, if the Host reads this data 32-bit word at a time, the byte order
would be intact. Report headers are not a problem because as they are
composed of 32-bit words. For FFT bins, read each DWORD at a time and
extract FFT bins out of that DWORD. Make this change in a generic way to
keep the design uniform across different chipsets and endian modes.
CRs-Fixed: 3042188
Change-Id: Idff1ac7eb5e18c692c9ee8b19b9ae9e6b962d486
There is a requirement to use REGDMN and wireless modes in UMAC layer of
the cmndev component. As the WMI_HOST_REGDMN modes currently are defined in
WMI layer, we can't use them directly in the UMAC layer. Hence move them
to the reg_services_public_struct.h and rename them as HOST_REGDMN modes.
Replace all WMI_HOST_REGDMN instances with HOST_REGDMN. Wireless modes are
currently defined in WIN component, use them to cmndev component.
CRs-Fixed: 3044590
Change-Id: Iee5fa1745a1a44b834334746b10bdbb6f6563a0a
Add change to handle service_ready for,
1. Ema multi-MBSSID group support
2. Large beacon support greater than 1.5K
CRs-fixed: 3036717
Change-Id: I1c985faf429aacd78ae74fe0ffe18958fd6aa821
In extract_time_sync_ftm_offset_event_tlv there is a possible
OOB write when value of num_qtime received from firmware is
greater than FTM_TIME_SYNC_QTIME_PAIR_MAX.
Fix is to add a sanity check for value of num_qtime received from
firmware to avoid the OOB write.
Change-Id: I6e57b1d716992d1a3c7d2f7ea911fefcbfbeff34
CRs-Fixed: 3033509
Currently WMI_TARGET_CAP_FLAGS_RX_PEER_METADATA_VERSION_SET is used
to the htt peer data version, this looks like is for the firmware
and host should use WMI_RSRC_CFG_FLAGS2_RX_PEER_METADATA_VERSION_SET
macro to send back this infromation back to the firmware.
Correct the macro to se the htt peer data version to the firmware.
Change-Id: I06cb86eaa05eda45fb524c77acce3248c90498d6
CRs-Fixed: 3032308
The flag WMI_SERVICE_HW_MODE_POLICY_OFFLOAD_SUPPORT indicates
whether HW mode selection offload is supported by firmware or
not.
If it's advertised in service capability, host should not set
HW mode explicitly, firmware takes control of managing HW mode.
Change-Id: I8939b44fd7ed3a674c4da91524c5d5622bf67ce7
CRs-Fixed: 3017054
hw_link_id is unique across psoc to identify pdev in multi-soc ML cases.
Exract hw_link_id from mac_phy_cap and provide APIs in target_if to set
and get this for pdev
Change-Id: I9dcc4c1e4b515e83151ca88f5f026c0dd0b04646
CRs-Fixed: 3023496
Add support for AFC specific Host service flags to switch
between LPI only and SP+LPI, disable AFC timer and request ID checks
in target.
Change-Id: I34d6adcad6e4a2cd6383c941ed07b98059daeed0
Add host WMI APIs to send WMI_PEER_ADD_WDS_ENTRY_CMDID,
WMI_PEER_REMOVE_WDS_ENTRY_CMDID, and WMI_PEER_UPDATE_WDS_ENTRY_CMDID
to the Fw.
Change-Id: I32afdac7c366b647ee3196bcb76531295e640b8b
CRs-Fixed: 2997227
Add support for extracting Thermal Stats Events
from thermal event TLV for FW event
WMI_THERM_THROT_STATS_EVENTID.
Also, added support for FW Cmd to request for
Thermal Stats: WMI_REQUEST_THERMAL_STATS_CMDID
Change-Id: I2bc80d082bda45e2255371bcb0c31d35d9806525
CRs-Fixed: 3016845
Add extract_roam_stats_event to wmi_ops to allow cld driver to register
the corresponding callback.
Change-Id: I77ebb05a1a2ce9fa0b2f2f2ffb50c523ab9070e6
CRs-Fixed: 3007690
WMI_MGMT_RX_REO_FILTER_CONFIGURATION_CMD is used to the configure re-order
criterion for incoming management frames. Add WMI layer support for the
same command.
Change-Id: If1498fd4fbccd86e7d54d9eac268868b36523d06
CRs-Fixed: 2960472
When MGMT Rx REO feature is enabled, FW will be sending MGMT Rx REO
parameters TLV as part of WMI_MGMT_RX_EVENTID for the frames that require
reordering. Add APIs to extract the same.
Change-Id: I57b132927cf413384d680b5778bfe6a2e2737adf
CRs-Fixed: 2960471
When MGMT frames are consumed by the FW, FW sends MGMT Rx FW consumed event
to the Host. Add WMI layer functionality for this event handling.
Change-Id: Id95f41a717b88589e861781e1111b17dc90475be
CRs-Fixed: 2959118
In the WMI_MGMT_RX_EVENTID event handling, add a length
check to validate if the buffer length sent by the firmware
is less than or equal to the actual buffer length.
Change-Id: I7db9af48bc525543b972dcaf40aee0a05d8f5023
CRs-Fixed: 3001331
In the WMI_PDEV_FIPS_EVENTID event handling, add a length
check to validate if the buffer length sent by the firmware
in fixed params is less than or equal to the actual buffer
length before processing the data.
Change-Id: I7a952d3e3a2f66060451263b72118a52aa89dd06
CRs-Fixed: 3009887
With latest architecture there are different HTT peer
data versions supported by the firmware, supported htt peer
version will be sent in the service ready and need to feedback
to the firmware in the init command.
Change-Id: Icd0470843198387cd7e0192cbe3821d45ef0534e
CRs-Fixed: 3008706
Add length sanity check for ibf cal value & phase delta
to ensure HOST always align with target defined length.
Also remove the REPORT_AOA_FOR_RCC flag usage.
Change-Id: I06e4a430143df1534849b8ec974e38932cff3ef1
CRs-Fixed: 2997030
Add new field ema_init_config to signal the configured value of
beacon size while using MBSSID feature in 6Ghz.
The current allowed range is 1500-3500 bytes.
CRs-fixed: 3004041
Change-Id: Id8cc1b7e4602b2e52b8eb215337070c6e3c26089
Add P2P_P2P_CONCURRENCY_SUPPORT service capablity to
validate whether fw can support p2p concurrency
support or not. when firmware advertises this flag it
can support MCC,SCC, DBS for p2p-GO/GC + p2p-GO/GC.
Change-Id: Ifec4bf984595b06374be9024601733c8537a9c3e
CRs-Fixed: 2984165
Add a function pointer to a function that converts host vdev param to FW
vdev param.
Change-Id: I01557d8bd87cb82548114626ff726aabba01dd19
CRs-Fixed: 3005160
Add debug prints when parsing the EXT chan list update event to dump the
reg rules received. The regulatory info is often updated and new bugs
are introduced every time so the prints will help narrow down the issue.
Change-Id: I229fa2e1432786c9a530f3a6035926135b2c4e2f
CRs-fixed: 3001297
Add storage for EHT mac and phy capabilities as
per 11be D1.0 and update the EHT mac and phy capability
sizes.
Change-Id: I67224b35b701235374772e9975375e695f3ed959
CRs-Fixed: 3000166
A new TLV is added to send partner link CSA/ECSA count offset to FW as
part of beacon template. Add WMI changes to populate these TLVs in the
beacon template send function.
To fix the compilation issue, added forward declaration of 'struct
vdev_mlme_obj' and removed 'include/wlan_vdev_mlme.h' include file from
wlan_mlo_mgr_public_structs.h.
Change-Id: I6e421b29bb887bec711a23db1458aca4d112ade4
CRs-Fixed: 2983249
In WMI INIT, check whether firmware supports the ack event or
not. If it supports then enable driver support and send it to
firmware during WMI INIT.
Change-Id: Icfdee6bc06e6a393de880b87fdab70665ea7c8b4
CRs-Fixed: 2987898
In case if TWT command (i.e setup, terminate, pause, resume,
nudge) comes from userspace and if the firmware is in below mode
1. scan in progress
2. roam in progress
3. CSA is in progress or
4. Any other error
then the command needs to be rejected in userspace context.
Synchronize the TWT command so that whenever command goes from
driver to firmware, then driver will receive ack event first
followed by respective event (i.e add dialog, delete dialog,
pause, resume, nudge) with below condition
1. If driver receives the ack event as successful then driver
waits for this ack event, respective event with status of the
TWT action frame over the air is expected.
2. If driver receives the ack event as failure then it will
rejects the TWT command in userspace context.
Change-Id: Ie885d98ecf2dad98d34676d889fd70e4c84f0a05
CRs-Fixed: 2987904
Add API to extract AoA phase delta and IbfCalValues from
WMI event. Also Add service bit to support the feature
Change-Id: I6f6514711345dd47c4be3673b8c40501feb763e9
Check the below service bits and set in psoc if the service is supported
by FW.
WMI_SERVICE_RTT_AP_INITIATOR_STAGGERED_MODE_SUPPORTED
WMI_SERVICE_RTT_AP_INITIATOR_BURSTED_MODE_SUPPORTED
Change-Id: I13504958bf31b2d645d915b4db20719bdc9a4133
CRs-Fixed: 2969195
Add WMI support for EHT puncturing by filling puncture
bitmap in vdev start and peer assoc commands.
Change-Id: If1d2541655558f22a96a741999ec4ff7348f695a
CRs-Fixed: 2982498
In the current implementation, csa_event_bitmap for CSA in the beacon
template WMI command is set to 0. Hence, the FW sends CSA complete event
to the host at the end of CSA complete.
Set the below values to csa_event_bitmap to get the current channel switch
count from FW to update the CSA/ECSA IE count in probe response frame.
1. WMI_CSA_EVENT_BMAP_ALL:
To get the CSA switch count event for every update to switch count.
2. WMI_CSA_EVENT_BMAP_SWITCH_COUNT_ZERO:
To get the CSA complete event only when the switch count becomes zero.
3. WMI_CSA_EVENT_BMAP_VALID_MASK:
FW to follow the bitmap for sending the CSA switch count event to the
host. Example,
0X80000000: Send the CSA event when the switch count becomes zero.
0X80000033: Send the CSA switch count to host for the count 0,1,4 and 5.
Change-Id: I8380d6badc3b84c72fde489e59b51b5ac122b97b
CRs-Fixed: 2978799
