There are duplicate macros for the same purpose, hence
replace WLAN_ALL_SESSIONS_DIALOG_ID with TWT_ALL_SESSIONS_DIALOG_ID.
Change-Id: I63130869eed8dffcce85fe6a04586592ab3eaca2
CRs-Fixed: 3047686
Enable more WoW logging modules to help with debugging by changing ini
gFwDebugWowModuleLoglevel=1,3,5,3,18,1,19,3,31,1,36,1,57,3.
Change-Id: Ib42e16188c2572d04971be0e28836797286faeac
CRs-Fixed: 3042611
Provide below APIs for easy mesh.
API to get the current frequency of the given VDEV.
API to get acs status of the given VDEV.
API to get cac status of the given VDEV.
API to get/set bandwidth of the given VDEV.
API to get band information of the given VDEV.
API to get connected STA count of the given VDEV.
API to get BSSID of the given VDEV.
API to get SSID of the given VDEV.
API to set channel of the given VDEV.
API to get/set cac timeout of the given VDEV.
API to get/set country code of the given VDEV.
Change-Id: Ia0bd201ad8155a66a4a8c5517f6fa43f3f358505
CRs-Fixed: 3027192
In open mode, driver sends PCL list to firmware as part of STA
connection completes. To send the PCL list, driver checks whether
active session increases or not. But in current scenario, first
STA connection complete happens and then active session increases
which results no PCL list to firmware.
As part of fix, first increase the active session and then do STA
connection completes so that PCL list will be send to firmware
after successful STA connection in open mode.
Change-Id: Ie920aad7d1d693f04e5b4c13806ec09078ffd8c9
CRs-Fixed: 3042257
gSuspendMode is for system suspend to choose between WoW and pdev
suspend. For RTPM suspend, should always enable WoW.
Change-Id: Ibf95ca79ded73f9c68e14b8dac4ec68d979f9db6
CRs-Fixed: 3047812
Currently, the bitmap of action frames that can wake up the
host during suspend is sent via the wmi command
WMI_WOW_SET_ACTION_WAKE_UP_CMDID. This bitmap doesn't include
DSCP action frames so currently the host doesn't wake up for
DSCP action frames when in suspend mode.
Enable wake up for DSCP action frame for runtime PM as well
as for wow mode.
Change-Id: I51ba3e8ef52755af25ed922161028dfbaccaa250
CRs-Fixed: 3046595
Update operational rates set, extended operational rates set
and MCS based rates set in VDEV MLME legacy priv object on
connect success.
Refine the APIs for fetching these rates.
Change-Id: I7697b3d2e26e2fc565a2e672afe19f255af89d7e
CRs-Fixed: 3044036
Fix few missing attribute in below connectivity events:
QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_EAP_RESPONSE
QCA_WLAN_VENDOR_DIAG_EVENT_TYPE_ROAM_SCORE_CURR_AP
Also send the roam candidate info properly to userspace.
Change-Id: Ia9c4f095316adf8f40294f1e119cad648749bb72
CRs-Fixed: 3037650
Currently in function extract_peer_stats_count_tlv,
num_peers is copied directly to wmi_host_stats_event
structure without any validation which may cause
out of bound issue if num_peers provided in fixed
param becomes greater than actual number of peer
stats info.
Fix is to validate num_peer_stats_info before populating
stats_param->num_peer_stats_info_ext.
Change-Id: Icfb1c4fd34d3ec9120064e14bb65e35f8539f7fd
CRs-Fixed: 3032139
As per new API changes, util_scan_get_ml_partner_info is modified to
pass the output pointer to ml partner info structure. Update caller
accordingly
Change-Id: I4da4a52a857eb147fe74f783136da71252e04444
CRs-Fixed: 3043820
During wma_pdev_hw_mode_transition_evt_handler()
get the freq range from mac_freq_mapping[] present in
wmi_pdev_hw_mode_transition_event_fixed_param and pass
till policy_mgr_hw_mode_transition_cb() and update
cur_mac_freq_range[MAX_MAC] from it. if no freq range
provided (legacy chipsets) then use
freq_range_caps[MODE_HW_MAX][MAX_MAC] to fill the
range depending on the new HW mode.
Change-Id: I145d48052ce37724b0f697c19a1041f5a908cb54
CRs-Fixed: 3044976
With g_sta_sap_scc_on_lte_coex_chan=0, when SAP working on 6Ghz,
STA connects to another 6Ghz unsafe channel, move SAP to 2G safe
channel for DBS. Add unsafe channel check in
policy_mgr_check_6ghz_sap_conc for such condition and select
alternate 2G channel.
Change-Id: If9d7be045835b4faa36b5d123f820032dabc2b64
CRs-Fixed: 3039791
In STA+STA roaming case, when primary interface is changed
and roaming is enabled on other interface rso stop will be sent.
But the roam scan mode is not set to 0.
So add check for primary interface change to reset roam scan mode
before sending RSO stop to FW.
Change-Id: Ia880b58a57b3d9b74f3c4e100d4724aac46b67cd
CRs-Fixed: 3042416
Fill the QCA_NL80211_VENDOR_SUBCMD_DIAG_DATA event data and
send the event to userspace.
Add dispatch table for the connectivity events to lookup
attribute type, id and length.
Change-Id: I1fc8467409852a430874ac1d926b06ec8dafb736
CRs-Fixed: 3030085
Fill the management frame data and enqueue the filled record to the logging
queue.
Frame sequence number, peer rssi, tx_status, authentiation algo,
authentication frame transaction sequence number will be filled to the
log record.
Change-Id: I069b7816fdc52eeed964d6586c52b58d1a5d5cd4
CRs-Fixed: 3030075
rem_len is calculated based on MAX size of the WMI message
(WMI_SVC_MSG_MAX_SIZE) while extracting data from
WMI_ROAM_STATS_EVENTID event data.
Correct this by considering the actual message length
received in the event.
Change-Id: If24f732a8fdc0ad403e9b8a936ff8cfa0b7f7737
CRs-Fixed: 3035196
STA connection with OWE transition mode SSID fails due to join
failure timeout. Since, it is OWE transition mode, STA needs probe
response for join success.
The scan table entry of the candidate BSSID is sent in the join request.
This entry is used to create session and to send probe request to AP.
In case of OWE transition mode, the beacon carries wildcard SSID.
Therefore, the scan table entry also has wildcard ssid. Also,
during the candidate selection, scm_ignore_ssid_check_for_owe check
allows even entries with wildcard SSIDs to be selected as candiates
for OWE transition mode.
The join request with Wildcard SSID in the scan entry is used by LIM
to create session, as well as to send probe request.Therefore,
the AP doesn't respond to the probe request with wildcard ssid
leading to join failure timeout.
This change adds ssid from connect request to the cm_vdev_join_req,
which can be used by LIM to create session and to send probe request
whenever the SSID in scan entry is wildcard.
Change-Id: I02e19e16f2620b5568fbff82ff29d394ab9ee00d
CRs-Fixed: 3041073
By default INI item igmp_version_support has value 0x7. Fix the comment
to match with the correct default value.
Change-Id: Iab0caf41b3f3a57873b8cae1188d475adcfe9cc5
CRs-Fixed: 3042427
Currently, interface change request failure is indicated
whenever qdf_delayed_work_start returns false which may
indicate wrong failure reason as qdf_delayed_work_start
returns false in case any other request is already started.
Fix is to update failure log of qdf_delayed_work_start
to avoid any wrong indication.
Change-Id: Icf75ab5eff5b225bb7a2db1d8327bde6bb4fc9ac
CRs-Fixed: 3042780
Add ini configuration to limit supported TX/RX HE MCS rates.
In case of XR use-case, higher throughput is not needed but
higher reliability is expected. So, this ini provide option to
limit HE MCS rate capability to MCS0-7 to achieve higher reliability.
Change-Id: Id6343f5b28d341e5ee377d11ad8420e3b8ded6ef
CRs-Fixed: 3033342
When SAP starts on 5G, initialize SAP mandatory list with
2G and 5G mandatory list. And also select same band channel
SCC channel firstly in the intersection of PCL and mandatory
channel list.
Change-Id: Iac86b5caf38bf72f143be81122f8378fc61b29e2
CRs-Fixed: 3039268
The 6GHz security check is enabled by default. Disable the check
if RF test mode is enabled.
Change-Id: Id6af514f6a31f6351b1b0d784c2b9f7d301496c0
CRs-Fixed: 3040621
When wifi is turned off, if the connectivity logging queue is
not empty, the wlan logging thread tries to dequeue the record
and send the logging event to the userspace. While performing
dequeue operation, the records from queue are copied to temporary
buffer before read pointer is incremented. There could be a
condition where this buffer is allocated in ini domain after stop
modules is done and freed in active domain if the wlan_logging
thread is preempted during stop modules.
So to avoid this domain mismatch, start the queue only if
start_modules is done and stop the queue after stop modules
to avoid dequeue being done during/after stop modules.
Change-Id: Ied8c36b19bc66474d3c4d8f913f3e3dbf9a574a0
CRs-Fixed: 3035644
Add support to parse roam frame info TLV.
Add changes to send the BTM request logging event.
Change-Id: I24fab5fc0ec204fce74cf822742b5a44b0e7774f
CRs-Fixed: 3013489
Using the HW capability from extended regulatory
capabilities (reg_cap_ext), fill the SMM/DBS/SBS
frequency range in such a way that if the frequency
range these for a particular mode is not at all
present in these reg_cap_ext, then maximum possible
range is selected for that Hw mode.
For SBS mode:
Derive the channel such that 2Ghz is supported only by
Mac0, and if the frequency range of 5Ghz and 6Ghz are
intersecting then derive the the 5Ghz/6Ghz range/
For DBS mode:
Mac0 Supports all the 2Ghz range and Mac1 supports the
maximum range derived from the reg_cap_ext of both Mac.
For SMM mode:
Derive the Freuency range based on supported bands.
With these changes, pure mac freq ranges can be stored
and used easily.
Change-Id: Ied7f81654ef6d135e14b053db9516b4cb591eb76
CRs-Fixed: 3034653
When band is changed from dual-band to single band
(2G only):
1. host need to remove IDLE & BTC trigger bits from
WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID
2. Send WMI_ROAM_IDLE_CONFIG_CMDID with enable=0
When band is changed from single band (2G only) to
dual-band:
1. host need to add IDLE & BTC trigger bits from
WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID
2. Send WMI_ROAM_IDLE_CONFIG_CMDID with enable=1
and with default configurations.
To configure the above value in FW, send an RSO
update to FW whenever host receives set band command
from the upper layer.
Change-Id: I5a78deee713ff8514640d1867098e4045b77a231
CRs-Fixed: 3033081
Currently, reject_ap_info is used at many places and memset is
not done before filling it. memset the buffer to avoid reading
garbage values.
Also, modify the current initialization of ap_info in
cm_add_bssid_to_reject_list to memset.
Change-Id: Ic0fabc1733c4ea63dccb2e45b2a2dc37791e594d
CRs-Fixed: 3040299
OFDM and CCK flags should not be set based on frequency. These
flags are already filled in pkt_capture_rx_get_phy_info based
on preamble.
Change-Id: Ie809ee2e3546ed69bedab12d73d408b379d6b73d
CRs-Fixed: 2965290
Currently, the ROAM event is posted to scheduler thread when it's
received from firmware. This is done to avoid processing the
complete event in IRQ context as the same callback gets called
from IRQ context for WOW events(WOW_REASON_LOW_RSSI and
WOW_REASON_HO_FAIL). Posting the ROAM event to scheduler
thread may introduce some additional delay in processing it back
as there would be a context switch.
If this ROAM event carries ROAM_START which is followed by a
ROAM_SYNC event, there is chance to process the ROAM_SYNC
before ROAM_START as ROAM_SYNC would be processed in the same
context whereas ROAM_START needs a context switch. This results
into an invalid connection manager state after processing
ROAM_START event, which results a connection failure.
Same is applicable for ROAM_PMKID_REQ_EVENT and
ROAM_VDEV_DISCONNECT_EVENT. Avoid reposting the same to scheduler
thread.
Change-Id: Ic4fc1b3baf12e4ceee9a0975ebfee77fb88ab6f0
CRs-Fixed: 3033657
Restrict the dequeue logic to send only 20 logs per second
to userspace. Add check to see if queue is empty before
trying to dequeue.
Change-Id: I778556c649d123718cf76c943c5b2ed7f6c6e8e5
CRs-Fixed: 3014554
Add new files for connect/roam logging. Add changes to
initialize the logging buffer.
Make changes to support enqueue/dequeue log.
Define enums for MAIN_TAG, Sub TAG, category.
Add structure definitions for logging buffer.
Change-Id: I1d283fcf464da90d4f5533214d480ddda156ec27
CRs-Fixed: 3013486
Currently average rssi is filled in rx packets as rssi not
available in rx tlv, but now ucode is providing rssi value
in rx tlv so do not fill average rssi as rssi is already
filled from rx tlv in packet capture component.
Change-Id: I67e5e4cf6f0eade0640012802d79fe92b87de001
CRs-Fixed: 3022166
Add support to allow/disallow three port combinations on
same band based on PCL table
Change-Id: Id2e9ad7d17bab6ea0aff6913b25f0eb330dc6c13
CRs-Fixed: 3028527
INI g_enable_go_force_scc states the force MCC to SCC mode.
Mode 1-strict: Implement force scc strictly as part of start bss
Mode 2-liberal: Turn on p2p go on provided channel and move
first p2p go to the new p2p go channel after set key.
Currently for p2p-GO forceSCC, support is present where no matter
what is the GO negotiated channel in start_bss, driver will force
the other GO/STA/GC channel (on the same band) to the current GO
channel. This is force SCC strict mode where value 1 is used for
g_enable_go_force_scc ini. In this mode GC will have to do full
scan as the GO channel may be different from actual negotiated
channel. DUT may see some issues if GC dosent do full scan in
this mode.
As part of this change, add support for value 2(Liberal mode)
in g_enable_go_force_scc ini. As part of this liberal mode,
driver will allow the GO to start in MCC mode and after set key,
it will check any other concurrent GO and will do forceSCC for
that GO to the newly formed GO channel.
Change-Id: Ifc7beb06335616c51dc064f48a78b825dbdbda25
CRs-Fixed: 2992098
Check fw capability to support p2p + p2p concurrency from
soc_fw_ext_caps and based on fw capability, set policy
mgr concurrency for p2p + p2p.
Change-Id: Ia32f81f37174e9d722911b1fae6d4897d0af9816
CRs-Fixed: 2991300
From the caller, the args comes as pm_ctx but in definition
it's assigned as work_info which causes crash.
Change-Id: I9928a2c3862407b02cb34356ad54895e1d3069c7
CRs-Fixed: 3035090
If flag WMI_SERVICE_HW_MODE_POLICY_OFFLOAD_SUPPORT is
advertised in service capability, host should not set
HW mode explicitly, firmware takes control of managing
HW mode.
Change-Id: I10a8ad5201db375cc21255661b7cf46b9dd6e05f
CRs-Fixed: 3017062
We have fixed using channel number as internal parameter instead of
chan frequency with change I60fe37d7d716eeaceaa00f3fb59c77b629ebacac,
but variables name are still chan which might cause confused to reader.
Rename all places where "chan" to "chan_freq", which actually channel
frequency used. And alter miss APIs which still expect channel number.
Change-Id: I948cbad133a17093f49384b563966d2c53b51707
CRs-Fixed: 3033951
According to 11n CERT case - 4.2.44 AP WAP/WPA2 mixed security mode
test, AP works in HT mode, but driver disallow the 11n when TKIP
cipher present and switch to "A" mode, then no HT IE in Beacon.
Fix by check TKIP only cipher and other ciphter present(CCM)
to disable allow 11n.
Change-Id: Ia915c9aa45bef93a22b5f43004e533cc87978752
CRs-Fixed: 3033301
Fix possible memory leak while updating dual sta connect channel list
in wlan_cm_dual_sta_roam_update_connect_channels.
Change-Id: I39dc05e485a0f00189978a38fa927a6ec4bd0086
CRs-Fixed: 3035192
Print channel list which is allowed for connection for the
second STA when dual sta roaming in is enabled in
wlan_cm_dual_sta_roam_update_connect_channels to enhance
debug log.
Change-Id: I4e16f101b60dc9d34d6193adcfe72ec173c5467a
CRs-Fixed: 3000235
Currently, firmware can roam between owe security SSID's
even though open SSID is different for both of the AP's.
This commit adds support to restrict roaming between the
same OWE profile AP's which means if the device needs to
roam then target AP's open SSID and owe SSID should match
with current AP.
Change-Id: Ib59127a90cab9ee6626b018d581edbf76ad89856
CRs-Fixed: 3025667
Send additional roam trigger TLV for BTC in
WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID
command, to support a new roaming trigger
"WMI_ROAM_TRIGGER_REASON_BTC".
Change-Id: Ib767bd6bcf005c187b0fb58986ad287fe8753c1b
CRs-Fixed: 3009788
To support BTC roaming, add a definition of BTC roam trigger
reason in ini roam_triggers. It goes to fw via roam_enable
trigger command (WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID)
Change-Id: I231a72ed98a74fb1b5ced12da7c3932af12d485d
CRs-Fixed: 3009787
Currently wlan_hdd_mgmt_tx path is still using legacy API to convert
channel frequency to number, it is not applicable for 6Ghz channel if
convert it back from number to frequency.
Fix it by replace all places where using legacy API to convert channel
and use channel frequency from supplicant directly. It can fix mgmt tx
from supplicant on 6Ghz channel.
Change-Id: I60fe37d7d716eeaceaa00f3fb59c77b629ebacac
CRs-Fixed: 3024898
