In case of aging out wds entries, avoid sending all
the wds delete wmi commands in a huge single burst.
Instead limit the maximum commands to half of the
wmi queue size. Inactivity will continue to be
marked every 120 secs but the inactive entries
will be flushed every 5 secs if there are pending
entries.
Change-Id: I6735704a0750ef466f1df798f0b354f4382098d6
CRs-Fixed: 2952682
Revert "qcacmn: drop duplicated EAP frames from REO exception path",
allow all EAP frame delivering to stack including retried ones.
Change-Id: I73733841c1feb21d5b5fd160856a8fe9c21168fc
CRs-Fixed: 2959701
As part of minidump enhancement feature, incorporate wlan driver
log_msg data structure into the minidump.
Change-Id: Ic68e199c645bf8c8be50e105391b5c6efa90decc
CRs-Fixed: 2946292
Currently IPA tx buffers are fixed at 1007 buffers.
Adding INI support to change number of TX buffers at load time.
Change-Id: Ide0357554f34759198276b9699e0e6f4a3e20051
CRs-Fixed: 2957916
Currently for UK ETSI1 is mapped due
to which reg list may skip some valid
channel list for UK in case of MCC and DSRC.
Fix is to map MCC to ETSI13_WORLD and
DSRC to ETSI10_WORLD.
Change-Id: Ibcc09e2c45506ee5d4d1cbbaf5763d6056a8ff71
CRs-Fixed: 2953624
Currently there are no sufficient debug logs during
AST cleanup of peers, to conclude in which context
the AST got freed up, hence adding more debug logs.
Change-Id: I5603d856aed8cc3860a78d24d51cd8b5386d38bb
CRs-Fixed: 2956910
Refine QDF_STATUS_E_NOSUPPORT to QDF_STATUS_E_ALREADY in
cm_check_for_reassoc_hw_mode_change() as QDF_STATUS_E_NOSUPPORT shows
that no need to do action for hardware mode change, it's not an
error or failure.
Change-Id: I6e977729f3c75cc23b921ea38728ff4c5aae7d75
CRs-Fixed: 2961362
Set the SAE EAPOL offload support in resource config based on
WMI_SERVICE_SAE_EAPOL_OFFLOAD_SUPPORT bit received in service
bitmap from Firmware.
Change-Id: I878736105c070df514dfe8d989541227b3baad11
CRs-Fixed: 2957082
Refactor FISA packet history to not access "struct rx_pkt_tlvs". This is
because this structure may be different for Li and BE chips and should
not be accessed directly and only via hal_soc->ops in common code.
CRs-Fixed: 2888556
Change-Id: I0d9f2785a81c130a2dc506020a02ee5581c0bbd3
Implement core DP rx processing to functions in to corresponding
architecture specific be/li rx files. Keep common utility functions
in DP common files.
Change-Id: I40083e10772fd2b6ce2f1fa9e197f2ad92d0522a
CRs-Fixed: 2891021
Move DP TX target specific functionality to dp/wifi3.0/be
and dp/wifi3.0/li folders. DP Functionality common to both lithium and
beryllium targets stays in dp/wifi3.0.
Change-Id: I3497284153e2ea30a9cb1faf05bd41422329b804
CRs-Fixed: 2891038
Add changes in datapath rx monitor mode APIs
to handle modification in HAL APIs for WCN7850.
Change-Id: Iec7fbf9389033dfa86e71b1081e6a64607125ecc
CRs-Fixed: 2888556
Beryllium targets have more number of HW rings.
Add INI changes to allow increase in number of rings.
Change-Id: I73d779334601d3a1c2aefcade1dcf9dd0f2ef761
CRs-Fixed: 2891021
Add the changes to the generic HAL APIs.
The APIs generic across lithium and beryllium
architecture are kept in common HAL code.
The APIs which are generic across lithium
chipsets are moved to lithium specific files.
The APIs which are generic across beryllium
chipsets are kept in beryllium specific files.
Change-Id: Ie5e28aca5de02aa42f63b4a13fcb1cb32ffa8a28
CRs-Fixed: 2891049
Assign th HAL TX/RX ops in a function instead of assining a structure
directly. This can be later extended to have default ops for a family of
chips and then override that with chip specific ops.
This also helps the case where a new hal_soc->ops needs to be added.
The new 'op' will need to be added to only a default ops initializer
(with assumption that it applies to all chips).
Change-Id: Iefa23d14110fa5252444fad89737a3b2b2fbab6f
CRs-Fixed: 2891049
Host add support to send cfr data via nl events to userspace
applications. Host registers callback when user send vendor
command to set transport mode.
Change-Id: Ieed3b6e09d871639af58336074313120d51762e2
CRs-Fixed: 2952096
If STA country code is US and 6G AP country IE is other than
US, STA would use VLP mode. Since US VLP is not determined
we don't allow connection to go through. Additionally, don't
include such AP to scan result.
Change-Id: I41b0c7dbea681b2ef1bea7c0a572ee1d7248fa6e
CRs-Fixed: 2953248
User sets CFR data transport mode using vendor command
QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. By default
CFR data transport mode is relayfs, user uses vendor command
attr QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE to set
transport mode QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS or
QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS.
If user sets QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_RECEIVER_PID
attr in QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG vendor
command then hosts uses RECEIVER_PID to send unicast NL events
for CFR data.
Change-Id: I40e896fad8af24e761fcbedeba761f4a3815f0b8
CRs-Fixed: 2952095
Currently, wrong address is given to insert session_id in
meta_data.
To fix this, Passing pointer variable instead of address
to the pointer so that meta_data is filled correctly.
Change-Id: I019d73dc728fb214fd7c06a5027f0507ab4822a1
CRs-Fixed: 2959923
Add a QCA vendor attribute to configure the driver to use Data or
Management frames for keep alive data. This attribute is used for
testing purpose.
Change-Id: I03b133f3d61c4d34b79e41ad72cfc24334380658
CRs-Fixed: 2960804
Add QCA vendor attribute to configure the driver to transmit the
Data frames with ER SU PPDU type format. This attribute is used
for testing purpose.
Change-Id: If11523ea3e6316c47181342c3acc8425da85ee1b
CRs-Fixed: 2960794
Add missing change I4ab3c956c3169b50a69c05d9ed1c36e055aeb586
in connection manager to disable OCV in STA RSN capability
if AP doesnt support it.
Change-Id: I84b666a489b8f2e410a4901b908f57edae86b5d4
CRs-Fixed: 2960828
Currently, host sends bw value to upper layer in response
of GET_USABLE_CHAN command. but upper layer requires bw
value in form of nl80211_chan_width enum and considering
bw value as invalid and resulting into 0 bw.
Fix is to populate bw value from ch_params.ch_width instead
of populating from curr channel list and then convert to
nl80211_chan_width from phy_ch_width in hdd.
Change-Id: I1937ac2b3282224861a200a5d956a6e92109328e
CRs-Fixed: 2957055
When handling RXDMA error marked frames that from MAC1,
wrong rx descriptor pool is referenced, so allocated
buffer length is incorrect and lead to skb crash. Make
changes to always uses mac0 rx descriptor pool for MCL
platform.
Change-Id: Ica01c3967d6248a23ea745da63149dae9cd56677
CRs-Fixed: 2945573
Configure the MBSSID info to FW for Tx AP connection to enable
MBSSID functionality in FW.
Change-Id: Ida415a5c8f1dcb66e8890595b5f3038a611d62a5
CRs-Fixed: 2959158
Make the following code changes in the 6G host regulatory database:
1) Fix the multiple compilation errors that are seen when the flag
COMPILE_REGDB_6G is enabled.
2) Change the order of 6G AP type in the structure
sixghz_super_to_subdomains g_6g_reg_dmn_9_tuples and
enum sixghz_super_to_subdomains, from SP-LPI-VLP to LPI-SP-VLP, to keep
it in line with enum reg_6g_ap_type.
3)Rename the members under reg_super_domain_6g to contain the hexcode
in the member names.
Change-Id: Ia28c214b217ae3fb21420d058872cff17e11a5b6
CRs-Fixed: 2857865
