Firmware aborts the ongoing scan upon receiving new scan
channel list (through WMI_SCAN_CHAN_LIST_CMDID). Channel list
might get updated from userspace through commands like
country code change, power level change(SET_FCC_CHANNEL),...
It affects the features that are dependent on that scan,
e.g. ongoing connection, p2p find, etc.. Few frames might
be stuck in firmware as the scan is canceled.
It's recommended to defer the scan channel list update till
the current scan is done. This is already supported and
guarded through the ini param enable_pending_list_req
but disabled by default.
Enable the ini param to make sure above scenarios are not
affected due to channel list update.
Change-Id: I4176bb6a03657cf32f0c099b72254d61207ea6ca
CRs-Fixed: 3250137
Add assoc link bit in mlo_support_link_band to indicate supported band of
assoc link.
bit4: 2 GHz
bit5: 5 GHz
bit6: 6 GHz
Change-Id: I8fa156f43656ba91b8622ce12034ddad0bcf28a2
CRs-Fixed: 3250252
Correct description of ratemask_set ini for VHT mode
to avoid wrong configuration.
Change-Id: I91b887d8268f8faa0d0c32f90da032d00eaa14f2
CRs-Fixed: 3198950
When the STA connects to a peer, max supported ch_width is
calculated and configured to firmware. This is calculated from
self and peer capability in case of STA/SAP. Cache this in
peer object. Currently, data path module isn't aware of the final
ch_width configured.
Fetch the phymode and covert it to the DP expected ch_width
format. Update the ch_width to DP.
phymode of NDI peers is not maintained in host. So, get the NDI
self phymode and update to DP.
Change-Id: I25993053ae1f129c8fc9a352a05c788451060b2d
CRs-Fixed: 3227453
WMI_ROAM_GET_VENDOR_CONTROL_PARAM_CMDID: Add support
for a new roam command to get vendor control parameters
from FW. Host needs to send proper param ID in command
(from enum WMI_ROAM_GET_VENDOR_CONTROL_PARAM_ID)
to get corresponding INI value from FW.
WMI_ROAM_GET_VENDOR_CONTROL_PARAM_EVENTID:
Add support for a new roam event to get param value
from FW. FW sends this event upon receiving
WMI_ROAM_GET_VENDOR_CONTROL_PARAM_CMDID command.
Change-Id: I03679bcf359a0f425aab7b9ea1c3cb6d84fbb0ca
CRs-Fixed: 3225160
Add support to parse a new INI named
"bss_load_trigger_6g_rssi_threshold/RoamCU_6GRSSIRange"
and send its value to FW via WMI_ROAM_BSS_LOAD_CONFIG_CMDID.
Min, Max and default value of this INI:
Min: -120
Max: 0
Default: -70
Change-Id: I9aa99d887553de4022fc0a31dc0644601cd340d6
CRs-Fixed: 3225548
In the current driver implementation, the default ini value of
gSoftApMaxPeers is set to 32, but for mobile devices, FW can
only support 10 SAP peers at max. Hence, change the default
value of gSoftApMaxPeers to 10.
Change-Id: I8c5a2a8422f02bb464a11d823f8528ebb88bb34c
CRs-Fixed: 3227078
When STA receives a connect req (C1) and it requires hw mode
change. Now the hw mode change resp will take the SME global
lock and call connection manager API, which will try to
acquire CM lock.
But if before that one more connect req (C2) is received in
another thread which has acquired CM lock before C1 can
acquire it, and this connect req C2 will also flush the C1
from CM queue. Now if C2 also require hw mode change, which
also require to acquire SME global lock.
So both connect will wait for each other to complete, leading
to deadlock.
To fix this, from hw mode change response, break the context
(by posting to scheduler thread) so that sme global lock is
released and C2 is processed.
As C1 is already flushed by C2, on scheduler thread execution
once it get CM lock it will be dropped silently, and C2 will
proceed with connect.
Change-Id: I14efb0f21442edcae90a4abea20cb0b9e06a0758
CRs-Fixed: 3223786
Currently host sends first, final bmiss count to fw
Add support for bmiss timeout(in seconds)
during wakeup as well as sleep state to fw.
Change-Id: Id748fabdff94f5fa3038bcea1b1cac733ac2dbe1
CRs-Fixed: 3224106
Add vendor handoff service bit capability support
WLAN_SOC_VENDOR_HANDOFF_CONTROL to check whether the FW
supports vendor handoff feature or not.
Change-Id: Ifdf541761716df9ca5b764c05714a8b501642354
CRs-Fixed: 3224573
Add support for new ini param RoamScan_InactiveTimer. This param
is similar to the existing roam_scan_period_after_inactivity but
unit change
Change-Id: I0e803decaba30fa3f2dfcd95dc62dc71aa1cb3cd
CRs-Fixed: 3016893
Add cfg item to enable/disable eMLSR mode for ML STA
under 802.11be op mode. The cfg value 0 corresponds
to default MLMR mode, 1 corresponds to eMLSR mode.
Change-Id: Ib02516aac8ac44aee6b40a572a9f7469b10d0ac2
CRs-Fixed: 3184745
Add support for new ini param RoamCU_MonitorTime. This param
is similar to the existing bss_load_sample_time but unit
change
Change-Id: Iae05a9568aa29a5f6a9cfc771e66184e51963ab6
CRs-Fixed: 3015967
set_primary_vdev usecase in STA+STA concurrency is to use that
interface(e.g. wlan0) over the other interface(i.e. wlan1) for
data transfer.
Non-primary vdev use case is to check the quality of that link
and decide if data can be switched to it and make it primary.
It may get disabled if it's not going to become primary STA after
measuring the link quality for sometime or with few APs.
Enable roaming on non-primary vdev also to find better AP.
Change-Id: I3205f1ee1b7da4aa813955308730949ccc70941f
CRs-Fixed: 3219633
Add support for new ini param RoamScan_SecondTimer. This param
is similar to the existing roam_scan_inactivity_time but unit
change
Change-Id: I65c7f88b95d102d9101d8dd59c662650706b247d
CRs-Fixed: 3015947
Add support for new ini param RoamScan_FirstTimer. This param
is similar to the existing gEmptyScanRefreshPeriod but units
change
Change-Id: If250ba41d71ef20c7365af2c90550b3b575d285c
CRs-Fixed: 3016232
Puncture bitmap is binding with channel bandwidth. If the STA can't
support bandwidth as AP broadcasts, STA need extract puncture bitmap
based on the negotiated bandwidth.
Generate puncture bitmap for STA based on negotiated bandwidth.
Change-Id: Iad303b220fc2e2c5a1b8c125f06300e414bf1fbd
CRs-Fixed: 3207676
Add cfg to configure the max number of links supported for mlo sta
connection.
Add cfg to configure the band bitmap that mlo sta connection supports.
Change-Id: I6b27a7eb13eff026c5123e4bd24ba2424dba781d
CRs-Fixed: 3202029
With this change add support for new ini ConDTIMSkipping_MaxTime
to set max modulated DTIM in ms.
Change-Id: I89ce2b5074ce75a1701365b5d09d8ed0244aeeef
CRs-Fixed: 3038346
SAP is allowed to come up on SCC with a STA operating
in 6GHz only if the STA is on a PSC channel in VLP mode.
Therefore, filter out all 6GHz channels from the PCL if
the STA operates on any non-VLP mode. Also, in case of
VLP mode, filter out non-PSC channels.
Change-Id: I37d9a510db3647fc07858af99eb614ebe824cc78
CRs-Fixed: 3206471
Add API ucfg_mlme_set_vdev_traffic_high_throughput &
ucfg_mlme_set_vdev_traffic_low_latency to configure the
high throughput and low latency to vdev. In MLO STA concurrency
cases, the host or target may disable a certain link
based on the flags.
Change-Id: Iaae7cfdeb55e0086572b071d83520278aa3425ea
CRs-Fixed: 3191501
In new framework the 6 GHz preferred SAP ACS config file will
contain 5 GHz channels, to avoid 6 GHz non-PSC being set to
MAX weight value and 5 GHz channels selected easily, here set
normalize_acs_weight to 90 for non-PSC channel of 6 GHz, 40
for 2 GHz and 5 GHz channels.
Change-Id: I5e89339d0fd4e3c190dd2ead1ec87d12ff197691
CRs-Fixed: 3186587
Add support for new ini param RoamCommon_MinRoamDelta. This param
is similar to the existing min_roam_score_delta param but units
change
Change-Id: If04ff2344a2651e7d8d71c92f05dfebc229f9fe1
CRs-Fixed: 3015930
Add support for new ini param RoamIdle_InactiveTime. This param
is similar to the existing idle_roam_inactive_time but unit
change
Change-Id: I857107a6d0e39f373e39d4fb9b762e7cf4c4a9e4
CRs-Fixed: 3015993
i.) Keep rf test mode ini disabled by default due to which
6G security check will be true.
ii.) while calculating TPC power, check safe mode & RF test
mode enabled or not and set power mode to LPI if
safe mode or Rf test mode is enabled.
iii.) During HE ops IE extarct set power type to VLP, if
6 G Hz info is not present in HE ops IE. So that power
type can be VLP in case ap_ctry is non US.
To get safe mode value, a new member is_safe_mode_enabled
is added in mlme private object and is set whenever
WIFI_TEST_CONFIG_6GHZ_SECURITY_TEST_MODE command is triggered
via userspace.
Change-Id: I4fc2a231f8e7d18e68b92af3f381456113668779
CRs-Fixed: 3192967
Currently we are reading early stop scan min and max
threshold to unsigned int, because of which we are
sending wrong values to FW.
Read early stop scan threshold min and max values
to signed int to send correct values to FW.
Change-Id: I2e96b3c3e9fb48352d8075a4e7a96eae41dacedc
CRs-Fixed: 3191076
Move wlan_mlme_get_wlm_multi_client_ll_caps API to dispatcher
folder so that other components would use this API to get
the multi-client feature capability flag.
Change-Id: Ib247401b9411c40a838b338a60d44cb187884480
CRs-Fixed: 3181381
The current maximum buffer size for an ADDBA response action frame is
256 bytes. This needs to be increased in case of EHT session.
Change-Id: I4e4dbe1dbe5c69954d26f73cf51177358c411083
CRs-Fixed: 3185336
Issue scenario, 1st Addba response tx and set is_mgmt_data_valid false.
2nd TX frame happens for valid frame that needs to be logged and set
wma_handle->is_mgmt_data_valid to true. Then the 1st frame TX completion
tried to access wma_handle->mgmt._data. It may access invalid context if
race condition happened.
Move management frames handling from lim_send API to tx_complete_cnf API
Change-Id: Ib5090dcd274160b3a9d7b9975d0839ec06616b86
CRs-Fixed: 3154710
Add multi-client latency level service bit capability support,
WLAN_SOC_WLM_MULTI_CLIENT_LL_SUPPORT, to check whether the FW
supports multi-client latency level event or not.
Add INI "wlm_multi_client_ll feature" to enable/disable multi
client latency level feature from the host side.
* @min: 0
* @max: 1
* @default: 0
If firmware sends multi-client latency level service
bit capability to host and host enables multi-client latency
level feature via INI, the host waits for an event
WMI_VDEV_LATENCY_LEVEL_EVENTID as a response to a request
command WMI_WLM_CONFIG_CMDID.
Change-Id: I5cbea89e67caabac5db70b7f0a91c18bdd512e9b
CRs-Fixed: 3180928
Add support to dump the full management,eapol,
dhcp, arp frames based on the level of the
debug_packet_log configured through ini gEnableDebugLog.
The dump levels are as follows:
* 0x1 - Enable mgmt pkt logs (except probe req/rsp, beacons).
* 0x2 - Enable EAPOL pkt logs.
* 0x4 - Enable DHCP pkt logs.
* 0x8 - Enable mgmt action frames logs.
* 0x10 - Enable ARP pkt logs.
* 0x0 - Disable all the above connection related logs.
Change-Id: If572cccb327da785dd0d56cff6d37ba170b15cc8
CRs-Fixed: 3173604
Add a new field max_mcs_index in mlme_legacy_priv to save max mcs
index of current vdev.
Add a new field max_real_mcs_idx in hdd_station_info to save max
mcs index of the connected station.
Change-Id: I28908515cbe5c18c79f14f8645defd5c82e3a6f0
CRs-Fixed: 3065838
Since HB failed logic change to send deauth, we don't
need probe logic after HB failed. Clean up timer and
unnecessary code.
Change-Id: I26d9235c157065a21469b01abf31751825a1f277
CRs-Fixed: 3158364
Generate a Level 2 update frame and send it to the bridge in SAP
mode when a new station connects.
It will update the forwarding table of all the bridge devices
through source port learning.
Change-Id: Ia804968453c051e4c8322d3735506a912c0d963d
CRs-Fixed: 2997409
Add new config to ease scan and connection restriction
in 6GHz band when bss is advertising different country.
Change-Id: I13bd0dbd52fad297b995add8fc8a71d7a058c25b
CRs-Fixed: 3135152
Replace blacklist/whitelist with denylist/allowlist in
qcacld3.0. and replace blm with dlm.
Change-Id: I9ba61dde3b3ea008ca3777448d1f8dab83d33ec1
CRs-Fixed: 3091211
During CSA max bw is selected for SAP in STA + SAP concurrency
for non-dfs channel and SAP is tear down after 60 sec of operation
due to STA is in 20Mhz and SAP is in 40Mhz with
IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag disabled.
This change is to select 20Mhz BW during CSA if channel bonding is
disabled.
Change-Id: If4ed3d9a080ed976a0f4be6704848ae4494c7bbc
CRs-Fixed: 3126074
Currently moderate latency level is not used. Rename moderate
latency level to XR latency level to be used in XR applications.
Change-Id: Ia7f65c3565f6704b9571161aabefb3a8b47cce1e
CRs-Fixed: 3116839
Currently regulatory channels are disabled for
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT vendor command
event if ini coex_unsafe_chan_nb_user_prefer is not set and if
STA operates on disabled channels which results in crash for
STA interface in STA + SAP SCC case.
Hence coex_unsafe_chan_reg_disable ini is controlled based
on coex_unsafe_chan_nb_user_prefer.
Ini behavior summary:
|----------------|----------------------|-------------|--------------------------------|
|User prefer ini | Reg chan disable ini | PLs | Expectation |
| | | | |
|----------------|----------------------|-------------|--------------------------------|
| 1 | 1 | LE | accept freq ext command and |
| | | | disable the regulatory channel|
|----------------|----------------------|-------------|--------------------------------|
| 0 | 0 | Non-Pixel SP| reject freq ext cmd driver and |
| | | | returns NOT SUPP |
|----------------|----------------------|-------------|--------------------------------|
| 1 | 0 | Pixel SP | accept freq ext command and |
| | | | Don't disable the reg channels|
|----------------|----------------------|-------------|--------------------------------|
Change-Id: Ia3acbc133cab4865d8ad69992e893be91439f856
CRs-Fixed: 3128908
Currently, for Broadcast TWT setup command, if peer does not
support TWT responder capability and supports broadcast TWT
capability then host rejects broadcast twt setup command
based on TWT responder capability.
Add condition to check the peer broadcast capabilities before
sending broadcast TWT setup request to firmware.
Change-Id: Iaa8941424d948d501655859564669baff4af9e69
CRs-Fixed: 3092276
Update latency flags inis to 64-bit configuration and use
lower 32-bit for firmware configuration and upper 32-bit
as host configuration. Also remove separate inis for host
latency flags.
Change-Id: Iff62b847f40ae7fa5f82948ec37d756144860474
CRs-Fixed: 3115853
