Due to certain write-once registers needing to be set during
bootup, assume that compander on will be the default usecase, unless
haptics SKU is used.
Change-Id: I7903f3a4bf1eae82b4b9302ddc4f1e4c59d2cad3
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update from SOC_ENUM to SOC_SINGLE to match rest of driver
implementation. Also remove remaining dev_mode enum references
in wsa884x driver.
Change-Id: I2a477c4fa8c29373ffa1e8e2eb599a0f1c61653d
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add check to validate bat cfg,
bat cfg register read compared to dts read
Change-Id: Ib62ae3b3535a75dbc7c71b2b2ac3752fb2e61156
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Update settings to match how swr_mstr_ctrl driver is using the
SWR settings to set the registers. Previously, an offset1 of
0xFF would write 0xFF to the register instead of skipping it, unlike
other swr settings. This is similarly true for SWR Slave setting
for bp_mode.
Change-Id: I3c5b2635c5a88a52639cbac9455a544d5cfee154
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add mod % 2 to allow dev_index to work with WSA2 Macro.
Also fix issues associated with incorrect parameter
checking of dev_index leading to potential array index
out-of-bounds issues.
Change WSA MODE mixer control to be SOC_SINGLE_EXT for
extra parameter validation.
Change-Id: I030ee64d87fa60c6b44feebf5ccb1265f4291cc1
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Match datatypes of variables in
lpass_cdc_va_macro_enabl_dmic() with
lpass_cdc_dmic_clk_enable() to prevent CFI issues.
Change-Id: Id378476b1aa6231c8542ca754124716af2b1f50b
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
While handling gpr callback, acquire wake lock with
timeout to avoid apps going to suspend and wake up if apps has
gone to suspend. It is required in order to make sure
SVA detections are handled properly with suspend scenarios.
Change-Id: I05e5792e4fa95cba074e936785357b26f8190865
Signed-off-by: Aditya Bavanari <quic_abavanar@quicinc.com>
Handle VMAX_CLAMP notification which is notified from charger driver
that hBoost is used by the charger firmware and haptics Vmax need to
be clamped to a specific level for the following vibrations.
Change-Id: I3d783467aad71e0d9b31a96120db7e89fd54c5cb
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
replace all dev(pr)_err/info logs
that could potentially flood kernel logs with
ratelimit functions dev_err_ratelimited and
dev_info_ratelimited
Change-Id: I32dc6002dead1a07622978c4de63d541c01982fd
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
idle detect thr is a fixed value, do not need to change
Add debug statements in idle detect control func
Change-Id: I68a049f8560a1a444c019df2dc09f7cf62b37d46
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
the offset between LPASS_CDC_WSA_RX_INP_MUX_RX_INT0_CFG1 and
LPASS_CDC_WSA_RX_INP_MUX_RX_INT1_CFG1 is 8 so updating
0x104 + 8* interp
update ng block register write for NG2 mode in Kundu
Change-Id: I44da894feebb5d25bd467ffd4d54adde111778e6
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Update equation that converts from the PBR table to
the correct register value.
Improve accuracy of truncation by moving the division
into one operation at the end of the formula and adding 1.
Update a few table values that were copied incorrectly.
Change-Id: I685c02778468e910820a90e2de216e0daf2491ac
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Use LEGACY source if any of the below use cases is met:
EAR, PBR OFF, IDLE, NG2 and PA GAIN <= 13.5dB
Use PRE-LA when: All other cases
Change-Id: Iace0c1f6fea367a73cd604b958bd5c8905d29509
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Cast returned u16 value to int in VA/TX macro: clk_div_get
to avoid possible data type warnings seen in function
caller.
Change-Id: I08943a26294ce54a207b739867292c01d090623e
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Interrupt from wsa883x are not handled as slave_irq is not set.
Add slave_irq for wsa883x to address this issue.
(cherry-picked from commit ddfc43e7c48dcbe9bbae45b5caacdd5bca441800)
Change-Id: I6b56aa88cca895e4e0e5871a7478f6859d45b03f
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
regmap_irq_chip->irq_drv_data is shared by all attached wsa
devices and point to last probbed wsa device. This will cause
interrupt handle issue. Update irq_drv_data per wsa deviece to
resolve this issue.
(cherry-picked from commit 1852682fbcebfb9f479c3d09a91c075049b90253)
Change-Id: I6ac0520a4074d74dfb28122e06eed6a86374c0ce
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
PA_ERR can happen during speaker path setup. Log the
error status in the interrupt handler and clear the error
status for next audio playback to resume properly on
the speaker.
Change-Id: I0490d4cdd6379ed779ce7f54ec8b56d5a7af0649
Signed-off-by: Phani Kumar Uppalapati<quic_phaniu@quicinc.com>
Update to 5.15 kernel dapm api.
Pin name no longer needs prefix as it is added in API.
Change-Id: Ibf967dd01a36decdf904eff9d5af2e315aa53f1c
Signed-off-by: Kunlei Zhang <quic_kunleiz@quicinc.com>
Only UVLO_irq, PA_ON_ERR_IRQ and PDM_WD_IRQ are enabled
on wsa883x. Enable all other IRQs to monitor if WSA is in
bad state.
Change-Id: Ia78f12520eda4b26c00776583a78b14b74771e0e
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
With current setting for VBAT_ATTN1/2/3, pop is heard when
battery is low. Update default value for these registers
to resolve pop issue.
Change-Id: Ic4002a4b30ecd04b04001ca5f16bac5745a803d7
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Add dummy PCM backend definition for virtual devices.
This is being added to support echo reference capture.
Change-Id: I7830f9adf963397d06b837add3f9e1c0fe31563c
