Extract agc gain information, CFO & rx_start_ts from
rx status and cfr peer capture event to CFR host metadata
Change-Id: Id896554f1da6920bd3eeced1298b07857d41a68b
Return type of "target_if_is_spectral_active" and
"target_if_is_spectral_enabled" is bool. Wrong return values
are send for this APIs in case of errors.
CRs-Fixed: 2845250
Change-Id: I2344676a1ada51e041bb5f7acac8aa22847bee5c
If Spectral scan is disabled(agile and normal mode disabled)
skip init/deinit of Spectral module. Also avoid user requests
to configure/start/stop scan. If either agile or normal mode
is disabled block user requests for that mode alone.
CRs-Fixed: 2840335
Change-Id: I81148e5580fe4bf991b97cd086c8e3a9ca78e77d
Add utility APIs to check Spectral scan is disabled for
a given pdev/psoc/mode.
CRs-Fixed: 2840317
Change-Id: I6820cfc056c697434a138ddf9d8d93b5796a4722
Add APIs to init Spectral feature caps in the upper layer of the
Spectral module.
CRs-Fixed: 2840249
Change-Id: Idfb34a9eec3a66c6d193be7bb828eeec30548ae7
Add target if APIs to initialize normal and agile Spectral
feature caps for a pdev.
CRs-Fixed: 2840247
Change-Id: I6c5385c2050007a5ff3f668ab3d6176328294549
Add APIs to check the agile and normal Spectral scan
capability of the target. This information is derived from
the advertisements from halphy via WMI events.
CRs-Fixed: 2840227
Change-Id: I2aae79b3342d8d74a1f4c00e813cae843a71106a
Use the hal_srng APIs that handle byte-order conversion of ring pointers
for big-endian platforms.
Change-Id: I2664636d5d2a1abfd7b643ea4c4d63d328a9880f
CRs-Fixed: 2845047
Swap each word of key_data before sending key install command.
This is needed since copy engine swap is enabled for big endian platform
and key needs to be plumbed in network byte order for decoding to happen
correctly.
Handle the swap in wmi layer since all other big endian conversions are
handled in this layer.
Change-Id: Ia6f0d579f3edaf32193c353ea2fe35cc40f55399
Direct Buf Rx has a source ring to communicate with the target.
The target updates its tail pointer in little-endian format and this update
doesn't go through any byte-order conversion at the target. On a big-endian
Host platform, this tail pointer will be read in reverse order of bytes.
To fix this, convert the tail pointer to the Host order before using it.
Change-Id: Ibcaf3d7507910ea81eeb895772241ab9861ee45a
CRs-Fixed: 2843259
WLAN chip components are little-endian based. When such a chip is attached
to a big-endian Host platform, there will be a mismatch in the order of
bytes for the data that is transferred between the Host and target.
Spectral HW module transfers the Spectral report directly to the Host DDR.
This transfer doesn't go through any byte-order conversion at the HW side.
So, to avoid invalid reads at the Host side on a big-endian platform,
convert the Spectral report to the Host byte-order before using it.
Change-Id: I742537f3a95ffca2e12b83535e83e2870ad06b10
CRs-Fixed: 2838371
If module is not registered for dbr in any platform it
results into Null pointer dereference.
Added Sanity check to avoid Null pointer dereference for
cfg80211tool wifi0 g_dbr_ring_status.
Change-Id: I9e68dfc9d58d70693184f53913cd7f2324d788c1
FFT bin is 10-bit wide in Spectral pack-modes 0 and 1. However, HW packs
just one FFT bin in a 32-bit DWORD by adding extra padding bits in
pack-mode 0. Currently, the Host reads the entire 32-bit DWORD to figure
out the FFT bin value. Instead, read the only useful bytes i.e.,
least significant 2 bytes of a DWORD. This approach is efficient,
especially on a Host that implements a byte-swap mechanism on FFT bins on
a big-endian Host.
Also, while dumping FFT bins for debug purpose, print the first 2 bytes of
an FFT bin in pack-modes 0 and 1.
Change-Id: I20ca8c4905671e80251dca07f80ce17801b98f5c
CRs-Fixed: 2831530
Currently, host decrements beacon switch count and sends
channel switch frame every time until count becomes 0 this
may introduce sync issue between fw and host.
To avoid sync issue csa switch count is offloaded to fw. fw
will send CSA_SWITCH_COUNT_STATUS_EVENTID once beacon count
becomes 0 and host will send vdev restart once it recives
CSA_SWITCH_COUNT_STATUS_EVENTID.
Change-Id: I60238e8e83b56ca4c6490f9516d673d14ef9c323
CRs-Fixed: 2831356
WLAN chip components are little-endian based. When such a chip is attached
to a big-endian Host platform, there will be a mismatch in the order of
bytes for the data that is transferred between the Host and target.
Direct DMA framework writes 64-bit values to its DMA ring entries.
These DMA ring entries are present in the shared memory between the Host
and the FW and the data transfer doesn't go through any copy engine.
So, to avoid invalid reads at the FW side on a big-endian platform, write
ring entries in little-endian format so that the FW reads them correctly.
Change-Id: I9c9189f914fdda335723c25fc05484487985447c
CRs-Fixed: 2828746
check csa_beacon_template service and set
WLAN_SOC_CEXT_CSA_OFFLOAD/25th bit of
soc_fw_ext_caps in psoc if service is
supported by fw.
Change-Id: I8dca74c805cc8696f261e0f791818bca579c80c8
CRs-Fixed: 2826451
In function target_if_crypto_set_key(), array pn's size is 16,
while params.key_rsc_ctr's length is 8, so the length of src
buffer(params.key_rsc_ctr in this case) should be used when
copying data to dest buffer(pn).
Change-Id: Ifa9156963c3da0234dbf8755a4d1f7bf3b96d0ff
CRs-Fixed: 2822715
FFT bin values can span 10 bits for HKv1, HKv2 and Pine.
This change is to cap the values to 8 bits for such case
on these platforms.
Change-Id: I144b00b1ed21a3281f79050bb1ab63bd857e47b1
CRs-Fixed: 2804192
In Pine 160/165 MHz following are the expected sequence of events.
1. Start scan WMI command
2. FW param WMI event
3. Direct DMA completion WMI events
If 3 and 2 happens in the reverse order (i.e., host receives a direct
DMA completion event before receiving a FW param WMI event), host assert
will be triggered.
This change removes the assert and drops the Spectral reports till
FW param WMI event is received.
CRs-Fixed: 2812403
Change-Id: I537d0077737baab8d3a8e90bdc4f9138690010bc
Firmware advertises the service capability bit
WMI_SERVICE_SCAN_CONFIG_PER_CHANNEL when it supports per channel
scan config flags. Get this and cache in psoc.
If firmware supports WMI_SERVICE_SCAN_CONFIG_PER_CHANNEL, it uses
the upper-12 bits(bit-20 to bit 32) of channel_list for flags and
lower 20-bits(bit-0 to bit-19) for frequency. If firmware doesn't
support it, then channel_list holds the frequency value only.
Fill the flags and frequency accordingly.
Change-Id: I88a6f29f61e1ecea75bc5574cadcbbfbb7f8b188
CRs-Fixed: 2806405
Add API to get/set the target global mode when the driver
is loaded (or) dynamically switched between modes
Change-Id: I65857ef57a17645da94301e26c0daddc30c5ad79
CRs-Fixed: 2809955
Move the resource configuration command after initializing
pdev wmi handle and just before wmi init command.
CRs-Fixed: 2801602
Change-Id: I3a476cbbccd5874c79cfa08f1252c728ebc9a5c6
fft bin size adjust parameter is no longer applicable for
QCN9100. Remove QCN9100 in the check for setting this paramenter.
Change-Id: Ibff3d2d618e20563add79e65e31a442d8d36ba61
CRs-Fixed: 2804120
Host gets spectral scan data after stopped spectral scan, then it
can't find out current vdev since vdev id is reset when stopping
spectral scan.
Change-Id: I082b784e998a7600c7f8ef14bf67b790942f3a5f
CRs-Fixed: 2779397
QCA6490 expects twt_ap_pdev_count 2, to bring up twt sap on 2g.
Currently twt_ap_pdev_count is derived from num of radios and is
1 in case of MCC.
Configure twt_ap_pdev_count value equal to number of phy
advertised by firmware in wmi service ready ext event, configure
under flag WLAN_TWT_AP_PDEV_COUNT_NUM_PHY if defined in kbuild
Change-Id: Ib3fa81d140b473daa253e32cde2e11aad1b78b4d
CRs-Fixed: 2786512
Spectral parameter state information is accessed in both
process context and tasklet context. Currently
qdf_spin_lock/qdf_spin_unlock is used to protect these data structures.
This can lead to deadlock in the scenario where the process holding the
lock gets preempted by the tasklet. To avoid this use
qdf_spin_lock_bh/qdf_spin_unlock_bh.
CRs-Fixed: 2776902
Change-Id: I6d188e55d5066241b5f38a655f4a587c9edb0b8b
wmi_unified_register_event has a return type of QDF_STATUS.
Handle the same return type in the following callers:
1. target_if_dfs_reg_ocac_event
2. target_if_dfs_reg_offload_events
3. target_if_reg_phyerr_events_dfs2
Change-Id: I622f6f6c4ff3b428a6407b6526e823083cc1fd8a
CRs-Fixed: 2767507
Firmware advertizes its support to place FST in CMEM,
export this capability to DP.
Change-Id: I265246bcfd38a36e34c4ede66e117a92bb185032
CRs-Fixed: 2772238
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: I29fd5e645c7b43c74e28494c83a6f7d460165e2e
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: If77efc6a5b451bf2cf4acb59d5a2126ce486f02f
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: Ia6d1781f2bf1eea85d4af357e37a00b1f78e264e
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: I18c687ad0564ec70e28cf1f33f26501dda6ee5c5
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: I1dc098793e1df658666343d4293fe3f1c02daf34
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: Icfa7946a447f3cfe8c6ce933a618e8dbb67bd6a0
wmi_unified_register_event return QDF_STATUS
Handle same return type in caller function
CRs-Fixed: 2764185
Change-Id: I87b1e6ee5e06e4e6af81395d977595335fe0bc5c
When user programs a non-zero scan count(say N), after receiving N
samples Spectral scan is supposed to be stopped. This change keeps track
of number of Spectral reports received from target and stops the
Spectral scan when programmed number of samples arrives at host.
CRS-Fixed: 2764935
Change-Id: Ibea0eeece4577fd6e0da302716869b05c900f917
The 2nd argument passed to the function is_primaryseg_expected
is used to index the array spectral->rparams.fragmentation_160 which
is of size 2.If the value of the argument is greater than or equal
to 2, the indexing will lead to array-out-of-bounds access.
The fix is adding the relevant validation check.
Change-Id: Iccf98b06c0546ad11ec67e93e14183214100107f
This change allow Tx VDEV of MBSS mode to configured
dynamically by reset the VDEVs.
This change includes FW service bit parsing, checking
VDEV state of all VDEVs, sending MBSS information in
VDEV start command
Change-Id: I46b13629bd1c07be86b408d72c2967642ce8542e
CRs-Fixed: 2759229
