Per flag detect_enable to enable/disable detecting
interop issues ap function in firmware.
Change-Id: I52617e3700a3c79fc5b72c53af6d4b8db5e97879
CRs-Fixed: 2602001
From upper layers the vendor specific control roam bitmap is
converted to unified enum roam_trigger reason. From this bitmap,
deriver the fw trigger reason bitmap at
convert_control_roam_trigger_reason_bitmap.
Depreciate the roam_control_trigger_reason enum.
Change-Id: I64ac273d88b696c32c5b72462454a8983774ef90
CRs-Fixed: 2631968
Extend radiotap header to append ACK status and tx retry count
for packets sent to virtual mon interface.
Change-Id: I51037ffd11dfdee49278d43643fb7861a514ee18
CRs-Fixed: 2627710
Send new flag WMI_ROAM_OFFLOAD_FLAG_SAE_SAME_PMKID through
11i offload param to indicate fw whether WLAN_SAE_SINGLE_PMK
feature is enable or not.
If flag is set, fw should use single PMKID for SAE roaming
between VSIE AP(s), else fw should complete roaming by
doing full SAE authentication.
Change-Id: I9c88772c9571230c38e2cfa41c8a0c79663572ab
CRs-Fixed: 2616046
In a few scenarios, the number of reg rules can be 0. For example,
for a 2Ghz-only radio there are no 5Ghz reg rules. In such cases,
if we try to allocate memory (0 bytes) the allocation function prints
an error message. Also, the allocation is not required. Therefore, avoid
the allocation when the number of rules is zero.
Change-Id: Ic9caf578541970e9cf12cdde181f23762f137db8
CRs-Fixed: 2622109
Add support for the following NAN messages in kmsg:-
1. NAN enable status
2. NAN, NDP match events
3. NDP channel info.
etc.
Change-Id: I7f67b67153904b7efe8a708e3f93d069e399395c
CRs-Fixed: 2618433
WMI_WLAN_PROFILE commands support for tlv path.
Add WMI profile enable and trigger commands in tlv path
Change-Id: I10f867b181b559b82c097d6a61236f2145549238
For restricted 80+80 MHz FR, target team initially added
wmi_service_bw_165mhz_support to indicate the target is capable of
supporting restricted 80+80 MHz.
Later, they have added wmi_service_bw_restricted_80p80_support to indicate
the same. Therefore rename wmi_service_bw_165mhz_support as
wmi_service_bw_restricted_80p80_support.
Change-Id: I12229b5d35911d4c34e63902c09592187d902bed
CRs-Fixed: 2621249
Firmware advertises WMI_SERVICE_ROAM_SCAN_CHANNEL_LIST_TO_HOST_SUPPORT
at the time of initialization, that means host can querry for roam scan
channels list to firmware.
Host driver sends WMI_ROAM_GET_SCAN_CHANNEL_LIST_CMDID to firmware to
querry roam scan channels list and firmware responds with an event
WMI_ROAM_SCAN_CHANNEL_LIST_EVENTID.
Change-Id: I419a0206d7b06b6186d0c333c951bca5206f342f
CRs-Fixed: 2620607
1)Configurable number of bytes to log
2)Add support to record only specific WMI command/events
Separate buffers are added to save user specified WMI commands and events
1.To record specific wmi cmd, e.g. WMI_VDEV_START_REQUEST_CMDID
echo 0x5003 > /sys/kernel/debug/WMI_SOC0_PDEV0/filtered_wmi_cmds
2.To record specific wmi evt, e.g. WMI_MGMT_RX_EVENTID
echo 0x7001 > /sys/kernel/debug/WMI_SOC0_PDEV0/filtered_wmi_evts
Results of recorded specific WMI command/events:
1. WMI commands, e.g.:
cat /sys/kernel/debug/WMI_SOC0_PDEV0/wmi_filtered_command_log
2. WMI events, e.g.:
cat /sys/kernel/debug/WMI_SOC0_PDEV0/wmi_filtered_event_log
CRs-Fixed: 2597854
Change-Id: I1e90a13ac0717f1f37ba998fb1d06a990d3f4fa2
Currently while printing commnad information new
line is added which needs to be removed.
Change-Id: I639508a9a14db173f8d61d7a55c4ec99db4f1a1f
CRs-Fixed: 2618863
Currently there are unnecessary/duplicate logging. Identify and
reduce those logs that are not necessary.
Change-Id: If47a4fc0762a7a11666771e76a56d4fa1013647b
CRs-Fixed: 2615419
The candidate_min_roam_score_delta in struct
wmi_roam_cnd_scoring_param at the interface definition and this causes
compilation issues with older host.
Rename candidate_min_roam_score to fix compilation error.
Change-Id: Ie214b386ef4c14be2cdcaec9be0d8b6c7f1e7f33
CRs-Fixed: 2617981
This patch adds the function to extract and parse the wmi events
WMI_VDEV_AUDIO_SYNC_START_STOP_EVENTID and
WMI_VDEV_AUDIO_SYNC_Q_MASTER_SLAVE_OFFSET_EVENTID. These events are
required for ftm time sync feature.
Change-Id: Ib17da82b7a8abfcff5d18125a0ba0e5249d6bf54
CRs-Fixed: 2615452
A service bit is added to indicate Firmware supports sending NSS ratio
information to Host and Host receives the NSS ratio information from
Firmware as part of service ready ext event. Save this service bit in
soc's extcap feature bit. Extract the NSS ratio info from service ready
ext event and save the results in wlan_psoc_host_mac_phy_caps structure
to calculate NSS value.
Change-Id: I8fbee48d872b0724bbb629ad38b3c959736a3c39
CRs-Fixed: 2612959
Add support to send DSCP-to-UP map table values to
FW over WMI cmd to update its corresponding map table.
Change-Id: I92c1464881282ead00714d0b115cffd34dc9ba1f
CRs-Fixed: 2617045
During CU and low rssi based roam triggers, consider AP as roam candidate
only if its roam score is better than connected AP score by at least
candidate min roam score delta.
Hence, driver adds support to set candidate min roam score delta in
firmware.
Change-Id: I98d2c4ed5599e5d6d52941c46a236e0e5ccd8ba8
CRs-Fixed: 2614118
Firmware advertises service capability bit
WMI_SERVICE_PEER_DELETE_NO_PEER_FLUSH_TIDS_CMD
when peer delete command takes care of flush
all tids functionality.
If this service bit is set advertised by FW
then host does not need to send the flush tid
command before sending the peer delete command.
Change-Id: Ic6632772eeebc7f1494f1dd5e9d533b2bc22e533
CRs-Fixed: 2609962
Update value of new ini for separate iface support for NAN
"nan_separate_iface_support" to fw through a command
WMI_INIT_CMDID.
Change-Id: I55830e0d16d86ee5a0bfa7d3e44c6309c0d3d54b
CRs-Fixed: 2612010
Currently, the driver rejects the roam stats event if any of the
roam trigger or roam scan or roam results tlv is not present.
Now the firmware will send neighbor report immediately after the
neighbor report response is received from AP instead of buffering
it as done before.
So do not parse the roam trigger, roam scan, roam result tlv if
the tlv is not present. Add new flag in the tlv parsing structure
if the TLV is not present.
Change-Id: I366d8853f7f45dcdac6d4aa5c3a8a12a8b602a4f
CRs-Fixed: 2610377
As part of new requirement WLAN subsystem needs to perform thermal
mitigation action as per the thermal state of the device. The
wifi hal sends vendor command QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD
with the thermal level parameter and wlan host performs the required
appropriate action. wlan host driver maps the thermal level to
corresponding duty cycle off percent value and duty cycle value,
send WMI_THERM_THROT_SET_CONF_CMDID cmd to FW.
Make changes to perform vendor command handling, mapping thermal level
to duty cycle value and communicating the thermal information to FW.
Change-Id: I5b455ae6483f3d5bf2fe708f40c32a55eb8b9bdb
CRs-Fixed: 2610404
This patch adds the support for forming tlv commands
WMI_AUDIO_SYNC_TRIGGER_CMDID and WMI_AUDIO_SYNC_QTIMER_CMDID.
CRs-Fixed: 2607605
Change-Id: Ifaf2b43b60cf604d79d5649b27632422850a0d61
Clear console log boot up error prints by removing unnecessary
prints, modifying prints to appropriate info or debug and
by fixing the errors
Change-Id: Ica3f126280399eef59b894236849e2079a62565f
CRs-Fixed: 2597026
Add support to fallback the PMKID generation from firmware to
wpa_supplicant.
Firmware fallbacks PMKID generation to host when FIPS enabled
due to the crypto library availability limitation.
Once the roam candidate selection is done in the firmware, it
sends the WMI_ROAM_PMKID_REQUEST_EVENTID. Once this event is
received, the host driver triggers an event to wpa_supplicant
for PMKID generation.
Change-Id: Ica00d27ce3f9f4a8f966261b38e238c389fcf05c
CRs-Fixed: 2507617
Avoid direct fw headers usage in init_deinit component since
can have functional impacts. The inclusion is done at wmi level
to fix the inconsistency of code.
Change-Id: I73cc1aac500cec041de81750b9c7654d21344e6c
CRs-Fixed: 2505399
Add WMI support for broadcast twt sta invitation and
sta kickoff. Additionally, update the current WMI twt
fields to include btwt recommendation and btwt persistence.
Change-Id: I88dee854557bbb8c3263f42041e0b90a07cdd27e
For Genoa, the WLAN FW enables IPA by default, if the
IPA is disabled by kernel config, the IPA status is
not same between wlanhost driver and WLAN FW. So add
such info in the first WMI command to let WLAN FW knows
the IPA state from host, and do the according copy engine
initialization, otherwise, the mismatch IPA copy engine
configuration will casue the Genoa FW assert.
Change-Id: Iec2f86ffb40b296c51bee41adc0d895beb200e5c
SAP not advertising 20TU probe response when
FILS Discovery is disbaled through ini.
Updated WMI fields to enable 20TU probe response
when 6Ghz SAP is operating.
Change-Id: Idc4b95047d2149f68a68a434afda4d325a5d0547
CRs-Fixed: 2600485
